BFC21103 Chapter5
BFC21103 Chapter5
BFC21103 Chapter5
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Hydraulic structures are artificial or natural structures that can be used
to divert, restrict, stop, or manage the flow of fluid. The structures can
be made from a range of materials such as large rocks, concrete, wooden
timbers or even tree trunks.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Examples of hydraulic structures are:
a. Sluice gate,
b. Spillway,
c. Weir,
d. Energy dissipator structures, and
e. Constrictor
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Sluice gates
Spillways
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Weirs
Energy dissipators
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.1 Sluice Gate
Sluice gates are used to control and measure rate of flow in open
channels (in hydropower plants, and irrigation channel).
Sluice gate
Hydraulic jump
Eo yo
Q y2
a y1
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Flow under Sluice Gate
Rate of flow under the sluice gate can be derived from the Bernoulli's
theorem, i.e.
po Vo2 p1 V12
yo y1
g 2g g 2g
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.1
A sluice gate is built in a rectangular channel with bottom width b
of 2.5 m. The flow and gate characteristics are yo = 2 m, = 0.625,
Cd = 0.610, and a = 0.5 m. Calculate the discharge under the sluice
gate if y2 = 1.8 m.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Given b = 2.5 m, yo = 2 m, = 0.625, Cd = 0.610, a = 0.5 m, y2 = 1.8 m
Since yo y1 y2
Q Cd ab 2gyo y2
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.2 Spillway
Spillway is built in a reservoir to allow the flow of water to safely
move downstream when the reservoir is full.
A spillway is shaped as a rectangular concrete channel that connects
the upstream and downstream regions of a weir.
The best design of a spillway is following the lower nappe of free fall
of flow (e.g. ogee spillway) and the best shape of the spillway surface
is parabolic with inverted curve at downstream.
Crest
Q H
Falling water nappe
Inverted curve
Spillway
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Sembrong dam spillway
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Ogee spillway is also known as the overflow spillway and is widely used
on gravity, arch and buttress dams. It is the most extensively used
spillway to safely pass the flood flow out of reservoir.
Ogee is shaped based on the underside curve of the nappe over a sharp-
crested weir
In high overflow spillway (H1 >
Hd), the discharge corresponds
to the maximum designed
capacity of the spillway, and H1 Hd
0.115H1
the crest of ogee spillway rises
up from point A (sharp-crested A
crest) to maximum rise of
0.115H1 then falls in parabolic
form.
Discharge coefficient Cd for
ogee spillway is about 20%
higher than Cd for weir.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.3 Weir
A weir is an overflow structure built across an open channel to
measure the rate of flow.
The weir offers a simple and reliable method of measuring the stream
flow.
Nappe
H1
Q
P
Sharp-crested weir
Weir has broad crest when the thickness of the crest is more than 60% of
nappe's thickness.
Weirs can also be categorised into submerged and non-submerged weirs.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.3.1 Rectangular Weir
Rectangular weirs are divided into suppressed weirs and contracted
weirs.
A weir is suppressed when the weir opening spans the full width of a
channel.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
The discharge coefficient is
H1 H1
C d 0.611 0.075 for 5 (Rehbock formula)
P P
H1
C d 1.10 1.15 for 5 20
P
3
P 2 H1
20
C d 1.06 1 for
H1 P
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.2
A suppressed rectangular weir 0.75 m high and 1.5 m long is used
to discharge water from a tank under a head of 0.5 m. Estimate the
discharge of the weir.
0.5 m
0.75 m
1.5 m
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Suppressed rectangular weir, P = 0.75 m, L = 1.5 m, H1 = 0.5 m
H1 0.5
0.6667
P 0.75
H1 H1
Since 5, C d 0.611 0.075
P P
C d 0.611 0.0750.6667
C d 0.661
3
2
Q C d 2g LH12
3
3
2
Q 0.661 2 9.81 1.5 0.52
3
Q 1.035 m3 /s
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Contracted weir has weir length that is smaller than the width of the
channel. Due to the presence of the end contractions, the effective
length of weir Le is smaller than the actual length of weir L.
H1
Le P
L
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Contracted weir can be contracted at both ends (number of
contraction n = 2) or only one end (n = 1). For suppressed weir, n = 0.
23
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
The discharge of a free-flowing rectangular contracted weir is given as
3
2
Q C d 2gLe H12
3
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.3
A rectangular weir 0.75 m high and 1.5 m long is contracted at both
ends (n = 2). Estimate the discharge if the weir is discharging water
from a tank under a head of 0.5 m.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Given P = 0.75 m, L = 1.5 m, H1 = 0.5 m, and n = 2
0.00451 H1
2
C d 0.607 1 0.55
H1 H1 P
0.00451 0 .5
2
C d 0.607 1 0.55 0.6702
0.5 0.5 0.75
3
2
Q C d 2gLe H12
3
3
2
Q 0.6702 2 9.81 1.4 0.52
3
Q 0.9796 m3 /s
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.3.2 Triangular Weir
Discharge over a triangular weir with vertex angle , under a head H1 is
given as
8
5
Q C d 2g H12 tan
15 2
where, Cd = coefficient of discharge (= 0.58)
H1
B
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.4
Calculate the discharge of flow through a triangular notch with
vertex angle of 60 and a head H1 of 0.5 m. Assume coefficient of
discharge to be 0.58.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Given = 60, H1 = 0.5 m, and Cd = 0.58
8
Q C d 2g H1 tan
52
15 2
5
8 60
Q 0.58 2 9.81 0.52 tan
15 2
Q 0.1398 m3 /s
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.3.3 Trapezoidal Weir
Discharge through a trapezoidal weir with side slope m : 1, is a
combination of flow through a suppressed rectangular weir with length
L, and a triangular weir with vertex angle of 2, where m = tan , i.e.
3
2 4
Q C d 2g H12 (L H1 tan )
3 5
H1
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
The trapezoidal weir with side slope 1(H) : 4(V) is known as Cippoletti
weir. The discharge through a Cippoletti weir is given as
3
2
Q C d 2g LH12
3
where, Cd = 0.63
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.5
A Cippoletti weir with width 0.5 cm is installed at a section of a
channel. Calculate the discharge when the head over the crest is
0.25 cm. Use Cd = 0.63.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Cippoletti weir with sides 1(H) : 4(V), L = 0.5 cm, H1 = 0.25 cm, Cd = 0.63
tan1 14.04
H1 1
4
L
3
2
Q C d 2g LH12
3
3
2
Q 0.63 2 9.81 0.005 0.00252
3
Q 1.163 10 6 m3 /s
Q 1.163 cm3 /s
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
5.4 Energy Dissipator Structure
Energy dissipator structures are commonly built at the lower end of a
spillway to reduce the kinetic energy of flow. These structures are built
to reduce damages caused by high kinetic energy flows.
When designing an energy dissipator for a specific location, one must
considers factors such as the site location, the dissipator structures, and
the discharge through the dissipator. An example of energy dissipator is
USBR stilling basin type III.
Stilling basin type III is very stable with a steep jump front and less wave
action downstream than stilling basin type II or free hydraulic jump. It is
recommended for discharges up to 18.58 m2/s per basin width with Fr =
4.5 to 17, and velocity of flow V1 = 15.2 m/s to 18.3 m/s.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Type of stilling basin (US Dept of the Interior, Bureau of Reclamation - USBR, 1984)
Flow
Stilling basin type I
Flow
Stilling basin type II
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Flow
Stilling basin type III
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Flow
Stilling basin type V
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Flow
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Flow
Flow
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
USBR stilling basin type III
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
USBR Stilling basin type III
There are 3 sets of blocks, i.e. A. chute blocks, B. baffle piers, and C. end sill.
s1
w1
h1 w3
s3
h3 1 1 h4
z3 z4
L2
L
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Sizing for USBR stilling basin type III
h4 1 1 y1
Fr
h1 = y 1 h3 = (0.168Fr1 + 0.63) y1
18
s1 = y 1 s3 = 0.75h3
z4 = 2.0
w 1 = y1 w3 = 0.75h3
t3 = 0.2h3
z3 = 1.0
L2 = 0.8y2
L = refer to the chart of length of jump on horizontal floor
Q
where, y1
BV1
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Ho
H1
V1
y1
y2
V1 2g H1 o
H
2
y2 1
1 1 8Fr12
y1 2
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
4.0
3.0
L 2.0
y2
1.0
0.0
0 2 4 6 8 10 12 14 16 18 20
V1
Fr1
gy1
Length of jump on horizontal floor
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Steps in sizing for USBR stilling basin type III
Step 1. Find V1, y1, Fr1, y2
Step 4. Determine L2, h3, s3, w3, t3 and quantity of baffle piers (block B)
B
No. of block B
s3 w3
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Activity 5.6
An 8 m-wide weir of a dam is discharging 80 m3/s of flow with H1 = 30 m,
and Ho = 5m. Design an USBR stilling basin type III downstream of the
spillway.
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Step 1. Find V1, y1, Fr1 and y2
Ho 5
V1 2g H1 2 9.81 30 23.23 m/s
2 2
Q 80
y1 0.4305 m
BV1 8 23.23
V1 23.23
Fr1 11.30
gy1 9.81 0.4305
y2
y1
2
1 1 8Fr12
0.4305
2
1 1 8 11.32 6.668 m
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Step 2. Determine length of basin L
From the figure of length of jump on horizontal floor,
L 2.75y2 2.75 6.668 18.34 m
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Step 4. Determine L2, h3, s3, w3, t3 and quantity of baffle piers (block B)
L2 = 0.8y2 = 0.8 6.668 = 5.334 m
h3 = (0.168Fr1 + 0.63) y1= (0.168 11.3 + 0.63) 0.4305 = 1.088 m
s3 = 0.75h3 = 0.75 1.088 = 0.8160 m
w3 = 0.75h3 = 0.75 1.088 = 0.8160 m
t3 = 0.2h3 = 0.2 1.088 = 0.2176 m
z3 = 1.0
B 8
No. of block B 4.902 5 blocks
s3 w3 0.816 0.816
h4 1 1 y1
Fr 11.3
1 0.4305 0.7008 m
18 18
z4 = 2.0
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
Assignment #5
Q1. Explain the functions of the following hydraulic structures:
(a) sluice gate
(b) weir
(c) spillway
(d) energy dissipator structures
Q3. A trapezoidal weir with side slope 1:4 and width of opening 0.5 m is
used to measure flow rate of a river. Calculate the discharge if the
head above the weir is 25 cm and Cd = 0.675.
- End of Question -
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)
THANK YOU
BFC21103 Hydraulics
Tan et al. (laiwai@uthm.edu.my)