PRESSURE

PRESSURE
PRESSURE CHANGES
1
Pressure
PRESSURE
Define the term pressure in terms of force and
area, and do calculations using the equation
pressure = force/area. 2
Pressure
• Pressure is the force per unit area

Force
Pressure Area

F
p A
• The SI unit of pressure is Newton per square
metre (N/m2). This unit is also called the Pascal (Pa).

Pressure 3
Pressure
• For a solid block resting on the floor, the pressure acting
on the floor is highest when the block is resting on its
smaller surface.

4
Pressure
1. Diagram below shows a cuboid of 2 kg on a table.
Calculate the pressure exerted on the table by the
cuboid.

Problem Solving 5
Pressure
2. A 6000 kg elephant standing on one of its feet exerts a
pressure of 600 000 Pa on the ground.
a) What is the area of its foot?
b) If its feet are the same size, what pressure would it exert
standing on all four feet?
3. A weight of a brick is 30 N. If its dimension is 20 cm by 30
cm by 30 cm, find the maximum and minimum pressure its
exerted?
4. A boy and a sled have a combined mass of 38 kg. The
runners of the sled are 1.60 m long and 1.2 m wide. Find the
pressure exerted on the snow.

6
Pressure
5. A block of metal of dimensions 0.5 m  0.6 m  1.0 m has a
mass of 300 kg. Calculate the maximum and minimum
pressure acting on the ground.
6. A force of 200 N acts on an area of 4 m2.
a) What pressure is produced?
b) What would the pressure be if the same force acted on half the
area?
7. A rectangular block of mass 30 kg measure 0.1 m by 0.4 m
by 1.5 m.
a) Calculate the weight of the block.
b) Calculate the maximum and minimum pressure exerted by the
block.

7
Pressure
8. What pressure is exerted on the snow by a 180 N skier
if his skis are 183 cm long and 13 cm wide?
9. Soft snow can be compressed by about 3000 Pascals of
pressure. What is the smallest area that a pair of
snowshoes must have if they will enable a 70 kg person
to walk over the snow without sinking in? Take g = 10
m/s2.

8
Pressure
10. A student pressing a thumbtack into a piece of wood
with a force of 20 N. The surface area of the head of
the thumbtack is 1 m2 and the cross-sectional area of
the tip of the thumbtack is 0.01 m2.
Calculate:
a) the pressure exerted by the student’s thumb on the head of the
thumbtack
b) the pressure of the tip of the thumbtack on the wood.
c) What conclusion can be drawn from your answers to (a) and
(b)?

9
Pressure
PRESSURE
Explain how pressure varies with force
and area in the context of everyday examples.
10
Pressure
Intensity of pressures exerted by a thumb and a drawing pin into a piece of
wood

Pressure Example 11
Pressure
A sharp knife has a very small surface area on its cutting edge so that high
pressure can be exerted to cut the onion.

Increasing the pressure

by reducing the area 12
Pressure
The high pressure on surface of the ice so that the ice melts and allowing the
ice skater to glide smoothly

Increasing the pressure

by reducing the area 13
Pressure
When a force is applied to the head of a nail, the pressure will drive its sharp
end into a piece of wood easily

Increasing the pressure

by reducing the area 14
Pressure
The pressure under the studs is high enough for them to sink into the ground,
which gives extra grip

Increasing the pressure

by reducing the area 15
Pressure
Rally need very high air pressure inside the tyres, because the narrow tyres
have a very small contact area with the icy road.

Increasing the pressure

by reducing the area 16
Pressure
Skis have a large area to reduce the pressure on the snow so that they do not
sink in too far.

Reducing the pressure by

increasing the area 17
Pressure
Wall foundations have a large horizontal area. This reduces the pressure
underneath so that the walls do not sink further into the ground.

Reducing the pressure by

increasing the area 18
Pressure
A load-spreading washer ensures that the nut is not pulled into the wood when
tightened up.

Reducing the pressure by

increasing the area 19
Pressure
A tractor moving on soft ground has wide tires to reduce the pressure on the
ground so that they will not sink into the ground.

Reducing the pressure by

increasing the area 20
Pressure
A wide shoulder pad of a heavy bag will reduce the pressure exerted on the
shoulder of the person carrying the bag.

Reducing the pressure by

increasing the area 21
Pressure
1. The diagram shows a thick sheet of
glass.
2. Which edge must it stand on to
cause the greatest pressure?

B 22
Pressure
 2. Which diagram shows the child exerting least pressure
on the ground?

23
B Pressure
 3. Four blocks, each weighing 10 N, rest on a horizontal
table.
4. Which block applies the greatest pressure on the
table?

A
24
Pressure
4. Which would be the least likely to sink into
soft ground?
A. a loaded lorry with four wheels
B. a loaded lorry with six wheels
C. an empty lorry with four wheels
D. an empty lorry with six wheels

25
Pressure
5. To prevent a cement mixer sinking into soft ground, the
mixer is placed on a large flat board.

26
Pressure
Why does this prevent the mixer sinking?
A. the large area decreases the pressure on the ground.
B. The large area increases the pressure on the ground.
C. The large area decreases the weight on the ground.
D. The large area increases the weight on the ground.

27
Pressure
6. A pin is squeezed between finger and
thumb.

28
Pressure
Which statement is correct?
A. The force of the pin is larger on the finger than on the
thumb.
B. The force of the pin is larger on the thumb than on the
finger.
C. The pressure of the pin is larger on the finger than on the
thumb.
D. The pressure of the pin is larger on the thumb than on the
finger.

29
Pressure
7. A farmer has two carts. The carts have the same weight,
but one has four narrow wheels and the other has four
wide wheels.

30
Pressure
1. In rainy weather, which cart sinks less into soft ground
and why?

D 31
Pressure
8. Two boys X and Y each have the same total weight and
are standing on soft ground.

32
Pressure
1. Which boy is more likely to sink into the soft
ground and why?

A
33
Pressure
9. A brick with rectangular sides rests on a
table.

34
Pressure
1. The brick is now turned so that it rests on the table
on its smallest face.

35
Pressure
1. How has this change affected the force and the pressure
exerted by the brick on the table?

C 36
Pressure
10. A builder leaves two identical, heavy, stone tiles resting
on soft earth. One is vertical and the other is
horizontal.

37
Pressure
1. After a few hours, the vertical tile has started to
sink into the soft earth, but the horizontal one has
2. not.
Which row correctly compares the forces and
the
pressures that the tiles exert on the earth?

C
38
Pressure
11. The diagram shows a glass block resting on a table
top.

39
Pressure
1. The area of the block in contact with the table is X and
the area of the table top is Y.
2. The weight of the block is P and the weight of the table
is Q.
3. Which expression gives the pressure
exertedon the table by the block?

40
Pressure
12. A brick of weight 80 N stands upright on the ground as
shown

41
Pressure
1. What is the pressure it exerts on the
ground?

C
42
Pressure
13. A small table weighing 40 N stands on four legs, each
having an area of 0.001 m2.
14. What is the pressure of the table on the
floor?
A. 400 N/m2
B. 1000 N/m2
C. 10 000 N/m2
D. 40 000 N/m2

43
Pressure
PRESSURE
Describe how the height of a liquid column may
be used to measure the atmospheric pressure.
44
Pressure
 • Water can is heated

Crushing Can 45
Pressure
  When the air inside the
can is cooled, its pressure
decreases.
 The high atmospheric
pressure outside exerts a
great force on the can and
causes it crashes.

Crushing Can 46
Pressure
The atmosphere is the layer of air enveloping the Earth. It
extends up to 1000 km above the surface and has a total
mass of 4.5 × 1018 kg.
The weight of air exerts a pressure on the surface of the
Earth called the atmospheric pressure. At sea level it is
about 105 Pa (100 000 Pa).
The pressure inside our bodies is almost the same as the
external pressure and so balances it.

Atmospheric Pressure 47
Pressure
  When the piston is pulled
up, the atmospheric
pressure inside the cylinder
will decrease.
 The atmospheric pressure
outside pushes the liquid up
into the syringe.

Syringe 48
Pressure
  When a person suck through the
straw, the pressure in the straw
become low.
 The atmospheric pressure outside
which is higher will force the
water into the straw and
consequently into the mouth.

Straw 49
Pressure
 When a vacuum cleaner is switched on, it sucks out the air
inside the cleaner, causes the pressure inside the cleaner
become low.
 The atmospheric pressure which is higher in magnitude, forces
the air and duct particles into the cleaner.

Vacuum Cleaner 50
Pressure
Atmospheric pressure can be measure using a simple mercury
barometer.
The atmospheric pressure act on the surface of the mercury in
the trough and support the vertical mercury column.
The atmospheric pressure is 760 mm Hg (millimetres
of
mercury) at sea level (equivalent to 105 Pa or 100000 Pa).
Simple Mercury Barometer 51
Pressure
• Mercury is more dense than water

Mercury Vs Water 52
Pressure
At High Altitude At Sea Level At Low Altitude

Low Pressure 760 mmHg High Pressure

53
Pressure
1. The diagram shows a simple mercury barometer.
2. Which height is a measure of the
atmospheric pressure?

C
54
Pressure
2. The diagrams show a simple mercury barometer.
3. Which diagram shows the distance to be measured to
find atmospheric pressure?

55
Pressure
3. The diagram shows a simple mercury barometer.

The atmospheric pressure increases.

Which distance increases?
A. VW
B. WY
C. XY
D. XZ

56
Pressure
4. A long tube full of mercury is inverted in a small dish
of mercury.

57
Pressure
1. The mercury level in the tube falls, leaving a vacuum at
the top.
2. When the atmospheric pressure falls,
which length decreases?

58
Pressure
5. The diagram shows a simple mercury barometer, used to
measure atmospheric pressure.

59
Pressure
1. Atmospheric pressure
increases.
2. What happens to the level L and to the pressure at
P?

60
Pressure
6. The diagram shows a simple mercury barometer.

61
Pressure
1. If atmospheric pressure increases, what happens to
level X and to level Y?

62
Pressure
7. The diagram shows a mercury barometer.
Which distance is used to
calculate the pressure of the
atmosphere?

A. 25 cm
B. 75 cm
C. 80 cm
D. 100 cm

63
Pressure
8. The diagram shows a simple mercury barometer.
The
barometer reading is hcm of mercury.

What is the pressure at S?

A. approximately zero
B. atmospheric pressure
C. atmospheric pressure + h cm of mercury
D. h cm of mercury

64
Pressure
9. The diagram shows a simple mercury barometer used to
measure atmospheric pressure.

Which statement is correct?

A. The pressure
at P
is
atmospheric pressure.
B. The pressure at P is nearly zero.
C. The pressure
at Q is
lower than the
pressure at P.
D. The pressure at Q is nearly zero. 65
Pressure
10. The diagrams show two mercury barometers standing
side by side. The right-hand diagram shows a tube of
bigger diameter, but the diagram is incomplete. There is
a vacuum above the mercury in both tubes.
11. Which labelled position on the right-hand tube could
show the mercury level in that tube?

B 66
Pressure
PRESSURE
Explain quantitatively how the pressure beneath a
liquid surface changes with depth and density of
the liquid in appropriate examples. 67
Pressure
• A liquid exerts pressure because of its weight.

Liquid Pressure 68
Pressure
• The liquid pushes on every surface in contact with it, no
matter which way the surface is facing.

Pressure acts in all

direction 69
Pressure
• The deeper into a liquid you go, the greater the weight of
liquid above and the higher pressure.

Pressure increase with

depth 70
Pressure
• The more dense the liquid, the higher the pressure at any
particular depth.

Pressure depends on the

density of the liquid 71
Pressure
• Whatever the shape width, the pressure at any
particular
or depth is the same.

Pressure doesn’t depend

of the shape of 72

container Pressure
• The pressure below the surface of a fluid can be calculated by
the following equation:

pressure = height × density × gravitational field strength

p=h××g

• where p is pressure difference in pascals

h = height in metres
 = density in kilogram per cubic metre
g = gravitational field strength in N/kg

Pressure Below Liquid 73

Pressure
 The wall of a dam is much thicker at the bottom than at the top
because it must withstand the increased lateral pressure in depths
of the water.
74
Pressure
Submarine is built with thick wall so as to withstand enormous
pressure at greater depth. 75
Pressure
Normally a water tank is placed at higher level so as to supply water
at greater pressure.
76
Pressure
A patient receiving intravenous drips of a
certain fluid from a bottle. In order for the
fluid to flow into the vein, the bottle must
be placed at a height above the injection
site, so it has sufficient pressure to flow
into the veins of the patient.

77
Pressure
Given that density of water is 1000 kg/m3, 1 atmosphere =
105 Pa and g = 10 N/kg.
1. What is the pressure at a depth of 23 m in
water?
2. Through what vertical distance does a diver mover to
increase the pressure of herself by 1 atmosphere.
3. A large tank holds a salad oil, density 0.9 × 103 kg/m3,
to a depth of 6 m. What is the pressure at the bottom of
the tank?
4. A dam is to be made to hold back an artificial lake 110
m deep. Find the pressure that the bottom of the dam
must withstand.

Examples 78
Pressure
5. If the density of sea water is 1150 kg/m3, calculate the
pressure below 40 m of sea water due to the water
alone.
6. The figure shows a cylinder containing liquid mercury.

What is the pressure caused by the

liquid mercury at the point P? [Density
of liquid mercury is 1.36 x 105 kg/m3]

79
Pressure
7. Calculate the increase in pressure as you dive from the
surface of a lake to a depth of 8 m
8. What is the pressure difference at 100 m below sea
level? (Density of sea water = 1030 kg/m3)
9. What is the total pressure at the bottom of a column of
mercury of height 15 cm? (Density of mercury = 13600
kg/m3)

80
Pressure
10. In the diagram
below;

81
Pressure
a) How does the pressure at A compare with the pressure at
B?
b) How does the pressure at B compare with the pressure at
D?
c) How does the pressure at A compare with the pressure at
C?
d) Calculate the pressure at B due to the water.
e) If thewater system were replace with paraffin,
how would this affect the pressure at B?

82
Pressure
1. What does not affect the pressure at a point beneath the
surface of a liquid?
A. area of the liquid surface
B. density of the liquid
C. depth of the point below the
surface
D. strength of the gravitational field

83
Pressure
2. Which statement about the pressure in
a column of liquid is correct?
A. It acts only vertically downwards.
B. It increases if the column width
increases.
C. It increases with depth in the column.
D. It is uniform throughout the column.

84
Pressure
3. Liquid X has a density of 1010 kg/m3. Liquid Y has a
density of 950 kg/m3.
The liquids are poured into tubes as shown. Which
tube has the greatest pressure on its base?

A 85
Pressure
4. Four different liquids are poured into
measuring cylinders. The diagrams show the depths of
identical
the liquids and their densities.
5. Which liquid causes the largest pressure on the base of
its measuring cylinder?

C 86
Pressure
5. Four flower vases have circular bases. They are
filled with water so that they all have the same
6. weight.
Which vase exerts the greatest pressure on its
base?

C
87
Pressure
6. The diagrams show two divers swimming in the sea and
two divers swimming in fresh water. Sea water is more
dense than fresh water.
7. On which diver is there the greatest
pressure?

88
Pressure
7. The diagrams show, to the same scale, the vertical
sections of a set of circular vessels, each containing the
same depth of water.

89
Pressure
Which one of the following statements is correct?
A. The water exerts the greatest pressure on the base of
vessel P.
B. The water exerts the greatest pressure on the base of
vessel S.
C. The water exerts the same force on the base of each
vessel.
D. The water exerts the same pressure on the base of each
vessel.

90
Pressure
8. Bubbles of gas, escaping from the mud at the bottom of
a deep lake, rise to the surface.

91
Pressure
As the bubbles rise they get larger.
Why is this?
A. Atmospheric pressure on the bubbles decreases.
B. Atmospheric pressure on the bubbles increases.
C. Water pressure on the bubbles decreases.
D. Water pressure on the bubbles increases.

92
Pressure
9. Four glass tanks contain water.
10. In which tank is the pressure of the water on the
base greatest?

A
93
Pressure
10. A student fills two containers with water (density 1.0
g/cm3) and two with oil (density 0.8 g/cm3), as shown in
the diagrams.
11. In which container is the pressure
on the base the greatest?

A
94
Pressure
11. The diagrams show two swimming pools. One contains
fresh water and the other contains salt water. Salt water
is more dense than fresh water.
12. At which labelled point is the pressure the
greatest?

95
Pressure
PRESSURE CHANGES
Describe the use of a manometer in the
measurement of pressure difference.
96
Pressure
A manometer consists of a U-
tube containing a liquid (either
mercury or water).
It is used to
measure gas pressure.
When one arm is connected to a
gas supply, the level of two
surfaces of the liquid will
indicate the strength of the
pressure

Manometer 97
Pressure
CASE 1

Pgas = PO + h
98
Pressure
CASE 2

Pgas = PO
99
Pressure
CASE 3

Pgas = PO - h
100
Pressure
1. The diagram shows an instrument used to measure gas
pressure.

What is the instrument called?

A. ammeter
B. barometer
C. manometer
D. thermometer

101
Pressure
2. A manometer is used to indicate the pressure in a steel
vessel, as shown in the diagram.

102
Pressure
1. What value does the liquid manometer give for
the pressure in the vessel?
A. It is zero.
B. It is between zero and atmospheric pressure.
C. It is equal to atmospheric pressure.
D. It is greater than atmospheric pressure.

103
Pressure
3. A manometer is being used to measure the pressure of
the gas inside a tank. A, B, C and D show the
manometer at different times.
4. At which time is the gas pressure inside the
tank
greatest?

D
104
Pressure
4. A water manometer is used to measure the pressure of a
gas supply to a house. It gives a reading of h cm of
water.

105
Pressure
1. Why is it better to use water rather than mercury in this
manometer?
A. h would be too large if mercury were used.
B. h would be too small if mercury were used.
C. The tube would need to be narrower if mercury were
used.
D. The tube would need to be wider if mercury were used.

106
Pressure
5. A water manometer is connected to a gas supply. The
diagram shows the water levels.

107
Pressure
1. The water is replaced by mercury, which is more dense
than water.
2. Which diagram shows the mercury levels when the
manometer is connected to the same gas supply?

108
Pressure
6. A pressure is measured using a manometer as shown in
the diagram.

109
Pressure
1. The water in the manometer is replaced with a
liquid which is more dense.
2. How does the value of h change?
A. It becomes zero.
B. It decreases, but not to zero.
C. It stays the same.
D. It increases.

110
Pressure
7. A manometer is connected to a gas supply.

111
Pressure
Pressure can be measured in cm of water.
What is the pressure of the gas?
A. 8 cm of water more than atmospheric pressure
B. 12 cm of water more than atmospheric pressure
C. 8 cm of water less than atmospheric pressure
D. 12 cm of water less than atmospheric pressure

112
Pressure
8. The diagram shows the levels X and
Y in a liquid manometer when
the gas tap is opened.

113
Pressure
What is the pressure of the gas in the cylinder?
A. 18 cm of liquid below atmospheric pressure
B. 9 cm of liquid below atmospheric pressure
C. 9 cm of liquid above atmospheric pressure
D. 18 cm of liquid above atmospheric pressure

114
Pressure
9. The diagram shows a simple manometer.

115
Pressure
1. Side X is connected to a gas supply. Side Y is open to
the atmosphere.
2. What pressure is the length h used to measure?
A. the atmospheric pressure S
B. the difference between the gas pressure R
and the atmospheric pressure S
C. the gas pressure R
D. the sum of the gas pressure R and the
atmospheric pressure S

116
Pressure
10. A water manometer is connected to a gas supply. One
end of the manometer is open to the atmosphere.

117
Pressure
1. Which statement about the pressure of the gas supply is
true?
A. The pressure is h cm of water.
B. The pressure is h cm of water below atmospheric pressure.
C. The pressure is the same as atmospheric pressure.
D. The pressure is h cm of water above atmospheric pressure.

118
Pressure
PRESSURE CHANGES
Describe and explain the transmission of pressure in
hydraulic systems with particular reference to the hydraulic
press and hydraulic brakes on vehicles.
119
Pressure
• Hydraulic systems work by using liquids under pressure.
They make use of two properties of liquids:
• Liquids are incompressible.
• If pressure is applied to an enclosed, the pressure is transmitted to all
parts of the liquid.
• In hydraulic press, a small force applied to the small piston can lift
a greater load on the large piston.

Hydraulic system 120

Pressure
 121
Pressure
Hydraulic brakes 122
Pressure
Hydraulic brakes 123
Pressure
• When the driver presses on the brake pedal of the car, pressure is
exerted on the brake fluid in the main cylinder.
• This pressure is transmitted along the brake pipes to wider cylinder
at the wheels.
• The oil pressure forces the piston in each wheel cylinder to push
the brake disc pads on to the wheel disc.
124
Pressure
Hydraulic jack 125
Pressure
• When the handle is pressed down, the piston in the narrow
cylinder is forced into the oil-filled cylinder.
• Oil is forced out of this cylinder, through the pipe and into a
wider cylinder.
• The pressure of the oil on the piston in the wider cylinder
forces this piston outwards which forces the pivoted
lever
to raise the car. 126
Pressure
1. Figure below shows a simple hydraulic jack. The load is just
being lifted using an effort of 20 N.

Calculate;
a) pressure at A,
b) pressure at B,
c) thrust acting on the piston C,
d) the load lifted?

example 127
Pressure
2. The hydraulic lift below is used to raise a vehicle so its
underside can be inspected.

128
Pressure
The lift has four pistons, each of area 0.01 m2 to lift the platform.
The pressure in the system must not be greater than 5.0 × 105 Pa.
The platform weight is 2000 N. Calculate the maximum load that
can be lifted on the platform.

129
Pressure
3. A jack is projected to lift a bus which has a mass of 4
000 kg. If the large piston has an area of 1 m2, and the
small piston on the other end of the circuit has an area
of 0.05 m2, what is the minimum force that must be
applied (to the little piston) in order to lift the bus?

130
Pressure
4. In a hydraulic machine force of 40 N is applied to piston of area
0.40 m2. The area of the other piston is 4.0 m2.

a) Calculate the pressure transmitted through the liquid.

b) Calculate the force on the other piston.
131
Pressure
5. In figure below, the force L is
200 N and the large piston on the right
rises 1.0 cm.

132
Pressure
a) Calculate the force F.
b) Calculate the volume of oil that enters the cylinder on the
right.
c) Use your answer to b to calculate the distance that the
piston on the left falls.
d) Explain why the effort force is less than the force F

133
Pressure
a) F = P.A = (200/100) × 20 = 40 N
b) Volume = length × area = 1 × 100 = 100 cm3
c) Length = V/A = 100/20 = 5 cm
d) The effort force produces a pressure in the liquid.
e) This pressure is transferred through the oil to the
right-hand piston.
f) The same pressure exerts a larger force
because
larger area of the piston.

Solution 134
Pressure
PRESSURE CHANGES
Describe how a change in volume of a fixed mass of gas at constant
temperature is caused by a change in pressure applied to the gas.
Do calculations using p1V1= p2V2
135
Pressure
 • Consider a gas is trapped in a cylinder by a
piston.
• If the piston is pushed in, the gas particles
will have less room to move as the volume
the gas occupies has been decreased.

Pressure & volume of gas 136

Pressure
• Because there has been a decrease in volume the
particles will collide more frequently with the
walls of the container.
• Each time they collide with the walls, they exert a
force on them.
• More collisions mean more force, so the pressure
will increase.

137
Pressure
• When the volume decreases the
pressure increases.
• This shows that the pressure of a gas is inversely
proportional to its volume.

138
Pressure
 139
Pressure
• From this we can derive the equation:

p 1V 1 = p 2V 2
p1 is the starting pressure
V1 is the starting volume
p2 is the finishing pressure
V2 is the finishing volume

140
Pressure
1. Calculate the unknown quantity in each of
the following changes involving a fixed mass of gas
at
constant temperature.
initial initial final final
pressure / Pa volume / m3 pressure / Pa volume / m3
(a) 100 0.20 50 ?

(b) 100 0.30 ? 0.15

(c) 120 ? 100 0.60

(d) ? 0.15 60 0.45

EXAMPLE 141
Pressure
2. If a given mass of gas has a volume of 4.5 × 10-5 m3 at a
pressure of 30.0 kPa, what will be the volume of the
gas if the pressure is increased to 50.0 kPa while the
temperature is kept constant.
3. The volume of a gas at 760 mmHg is 1250 ml. What is
its volume at 950 mmHg? Assume that there is no
change in temperature.
4. A 600 cm3 sample of gas is in a cylinder under a gauge
pressure of 1.8 atm. What will the pressure gauge read
if the sample is compressed to 180 cm3 at constant
temperature?

142
Pressure
5. To compress nitrogen at 1 atm from 750 ml to 500 ml,
what must the new pressure be if the temperature is
kept constant?
6. The pressure on 6.0 L of a gas is 200 kPa. What will be
the volume if the pressure is doubled, keeping the
temperature constant?
7. A gas measuring 525 ml is collected at 104.66 kPa.
What volume would this gas occupy at 99.33 kPa?

143
Pressure
8. A container holds 600 litres of air at a pressure of 2
atmospheres. If the pressure on the gas is increased to 5
atmospheres, what will its volume become?
9. A gas cylinder has a volume of 0.4 m3. It contains
butane at a pressure of 100 kPa and a temperature of 20
ᵒC. What pressure is needed to compress the gas to a
volume of 0.05 m3 at the same temperature

144
Pressure
10. A bicycle pump contains 400 cm3 of air at atmospheric
pressure. The air is compressed slowly. What is the
pressure when the volume of the air is compressed to
125 cm3. (Atmospheric pressure = 100 kPa)

145
Pressure
1. The system shown in the diagram contains a
liquid.

146
Pressure
1. A downward force of 80 N is exerted on piston K.
2. What will be the upward force exerted by the liquid
on piston L?
A. 1 N
B. 4 N
C. 80 N
D. 1600 N

147
Pressure
2. The diagram shows the principle of an hydraulic
system.

148
Pressure
1. The cross-sectional area of the master cylinder is 12.0
cm2 and the cross-sectional area of the slave cylinder is
8.0 cm2. The force applied to the master piston is 60 N,
producing a pressure of 5.0 N/cm2.
2. Which line in the table is correct?

149
Pressure
3. A student places his thumb firmly on the outlet of
a bicycle pump, to stop the air coming out.

150
Pressure
1. What happens to the pressure and to the volume of the
trapped air as the pump handle is pushed in?

151
Pressure
 4. Which graph shows the relationship between the
pressure and volume of a fixed mass of gas at constant
temperature?

152
Pressure
5. A measured mass of gas is
placed in a cylinder at atmospheric
pressure and is then slowly compressed.

153
Pressure
If the temperature of the gas does not change, what happens
to the pressure of the gas?
A. It drops to zero.
B. It decreases, but not to zero.
C. It stays the same.
D. It increases.

154
Pressure
6. Diagram 1 shows some air trapped in a cylinder.
7. Diagram 2 shows the same air after the piston has been
pushed in slowly.
8. The air in diagram 1 is at atmospheric pressure PA.

155
Pressure
1. What is the pressure of the air in diagram
2?

156
Pressure
7. A gas is trapped inside a cylinder by a movable piston.
The length of the gas column is 50 cm and the pressure
inside the cylinder is p.

157
Pressure
The piston is pushed in a distance of 30 cm, so that the
length of the gas column is now 20 cm.
The temperature of the gas does not change.
What is the new pressure of the gas?
A. 0.4 p
B. 0.6 p
C. 1.5 p
D. 2.5 p

158
Pressure
8. An airtight container holds a fixed quantity of gas. Its
pressure and volume are measured on four occasions
when the temperature is 20 ᵒC.
1. The results are shown in the
table.
2. Which set of readings is
incorrect?

159
Pressure
9. The pressure of a fixed mass of gas in a cylinder is
measured. The volume of the gas in the cylinder is then
slowly decreased.
10. Which graph could show the change of pressure of the
gas during this process?

160
Pressure
 C
161
Pressure
10. A piston traps a certain mass of gas inside a cylinder.
Initially the piston is halfway along the length of the
cylinder.
11. The piston is now moved towards the open end of the
cylinder. The temperature of the gas remains constant.

162
Pressure
1. How are the density and the pressure of the gas affected
by moving the piston?

163
Pressure
11. Some gas is trapped in a large syringe by a piston. The
atmospheric pressure is 100 kPa.

164
Pressure
1. The pressure gauge indicates that the gas pressure is 200
kPa above atmospheric pressure. The piston moves
outwards and the volume of the trapped gas doubles.
The temperature remains constant.
2. What is the new gas pressure?

165
Pressure