Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 15 views

    Wave Propagation Simulation in Abaqus PPT 123

    Uploaded by

    Palash Dongre
    Wave propagation Simulation for 2d plate in Abaqus

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd

    Wave Propagation Simulation in Abaqus PPT 123

    Uploaded by

    Palash Dongre
    15 views9 pages
    Wave propagation Simulation for 2d plate in Abaqus

    Original Title

    Wave Propagation Simulation in Abaqus ppt 123

    Copyright

    © © All Rights Reserved

    Available Formats

    PPTX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Wave propagation Simulation for 2d plate in Abaqus

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    15 views9 pages

    Wave Propagation Simulation in Abaqus PPT 123

    Uploaded by

    Palash Dongre
    Wave propagation Simulation for 2d plate in Abaqus

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    of 9

    Wave Propagation Simulation in

    Abaqus
    Lamb Wave Analysis using ABAQUS

    Elastic Wave

    • Elastic wave propagation is dependent on


    the density and elastic modulus of a
    medium

    • Longitudinal and Transverse wave speed is


    depends on Young’s and Shear Modulus,
    respectively

    Plate Geometry

    • 1meter long X 0.5 meter wide X 0.01m


    thick
    Lamb Wave Analysis using ABAQUS

    Symmetric vs Anti-symmetric mode

    • Typically, Symmetric and Anti-symmetric


    wave generated simultaneously for general
    elastic medium. Since, existence of many
    modes in the response makes analysis
    difficult., isolating So and Ao from other
    modes(S1, A1, S2…..) is recommended. To-do
    is frequency-thickness product(fd) needs to
    be less 2.0MHz.

    • S0 mode is the fastest wave as shown in


    velocity dispersion curve, it typically used as
    signal for health monitoring
    Lamb Wave Analysis using ABAQUS
    Determining element edge length

    • In order to capture propagating wave, at For isotropic,


    least 5~10 element per wavelength is G=
    adequate

    • To decide proper element size, 1st step is to


    calculate transverse wave speed
    • We used 10mm thick sheet, fd=2MHz,
     Ct = 3052m/s therefore, max frequency is 0.2Hz

    • Minimum smallest wavelength is calculated;

    Material STS321

    Min wavelength =
    15 mm
    * therefore, typical min element size would be
    1.5~3 mm
    Lamb Wave Analysis using ABAQUS
    Determining step size
    · If you want make lower
    • adequate integration time step is important for accuracy. frequency which can
    travel longer, it needs
    • typically 20 points / cycle of the highest frequency results is reasonable. high magnitude to avoid
    elastic wave
    • Deciding time step needs two criteria 1] Courant, Fredrichs, Lewy criterion
    attenuation. If media is
    2] Moser criterion embedded in soil, the
    various materials in soil
    which contacted
    to steel sheet could
    interfere the wave
    propagation, resulted in
    more signal attenuation.
     Select 10kHz excitation for following Therefore, frequency
    Analysis - element size is around 10mm
    and magnitude for
    - increment step size is 1e-6 sec* Too small element size give an error
    excitation signal needs to
    be carefully considered.
    Lamb Wave Analysis using ABAQUS

    Application of Lamb Wave in SHM(structural health monitoring)

    • SHM system involving Lamb wave can be differentiated into two type, Passive/Active system

    • In Active system, Lamb wave are excited into structures using actuators and then sensed back by sensors with
    damage information
    * exciter: Ultrasonic transducers, Laser Transducers, Piezoelectric transducers, Optical fiber trd
    Lamb Wave Analysis using ABAQUS

    Simulation of Lamb Wave

    • Application of Lamb wave in real world have severe complexity.

    • Thus, Numerical simulation is one of the best way to understand Lamb wave behaviour.

    • Check the elastic wave propagation pattern with


    excitation frequency and step time.

    • Experiment with the step size and frequency in the


    Abaqus model and review the wave propagation
    pattern.
    Lamb Wave Analysis using ABAQUS

    Lamb Wave Signal Analysis - Plate


    Lamb Wave Analysis using ABAQUS

    Future Work

    • Collect Data on for different Frequencies and Different Form of Defects like for
    different point loads applied, different locations, etc.

    • Use Machine Learning methods to train collected Data to make prediction for
    Structural health.

    You might also like