Steel Members Design

CE 405: Design of Steel Structures Prof. Dr. A.
Varma
1.0 INTRODUCTION TO STRUCTURAL ENGINEERING
1.1 GENERAL INTRODUCTION Structural design is a systematic and iterative process that involves: 1) Identification of intended use and occupancy of a structure by owner 2) Development of architectural plans and layout by architect 3) Identification of structural framework by engineer 4) Estimation of structural loads depending on use and occupancy 5) Analysis of the structure to determine member and connection design forces 6) Design of structural members and connections 7) Verification of design 8) Fabrication & Erection by steel fabricator and contractor 9) Inspection and Approval by state building official
Ideally, the owner and the architect, the architect and the engineer, and the engineer and the fabricator/contractor will collaborate and interact on a regular basis to conceive, develop, design, and build the structure in an efficient manner. The primary responsibilities of all these players are as follows: Owner - primary responsibility is deciding the use and occupancy, and approving the architectural plans of the building. Architect - primary responsibility is ensuring that the architectural plan of the building interior is appropriate for the intended use and the overall building is aesthetically pleasing. Engineer primary responsibility is ensuring the safety and serviceability of the structure, i.e., designing the building to carry the loads safely and ___________. Fabricator primary responsibility is ensuring that the designed members and connections are fabricated economically in the shop or field as required.
CE 405: Design of Steel Structures Prof. Dr. A. Varma
Contractor/Erector - primary responsibility is ensuring that the members and connections are economically assembled in the field to build the structure.
State Building Official primary responsibility is ensuring that the built structure satisfies the appropriate building codes accepted by the Govt.
1.2 STRUCTURAL DESIGN Conceptually, from an engineering standpoint, the parameters that can be varied (somewhat) are: (1) the material of construction, and (2) the structural framing plan. The choices for material include: (a) steel, (b) reinforced concrete, and (c) steel-concrete composite construction. The choices for structural framing plan include moment resisting frames, braced frames, dual frames, shear wall frames, and so on. The engineer can also innovate a new structural framing plan for a particular structure if required. All viable material + framing plan alternatives must be considered and designed to compare the individual material + fabrication / erection costs to identify the most efficient and economical design for the structure. For each material + framing plan alternative considered, designing the structure consists of designing the individual structural components, i.e., the members and the connections, of the framing plan. This course CE405 focuses on the design of individual structural components. The material of construction will limited be steel, and the structural framing plans will be limited to braced frames and moment resisting frames.
1.3 STRUCTURAL FRAMEWORK Figure 1 shows the structural plan and layout of a four-story office building to be located in Lansing. Figure 2 and 3 show the structural elevations of frames A-A and B-B, respectively, which are identified in Figure 1.
25 ft.
25 ft.
35 ft. Pin/hinge connection Fix/moment connection
35 ft. Frame A -A Frame B-B
35 ft.
Figure 1. Structural floor plan and layout

R 10 ft. E 12 ft. D 12 ft. C 12 ft. B 15 ft. A F K H M I N S T J P Q O
25 ft.
25 ft.
Figure 2. Structural elevation of frame A-A
g 10 ft. f e 12 ft. d 12 ft. c 12 ft. b 15 ft. a
n m l
u t s
b1 a1 z
35 ft.
35 ft.
35 ft.
Figure 3. Structural elevation of frame B-B As shown in Figure 1, the building has two 25-ft. bays in the north-south direction and three 35 ft. bays in the east-west direction. There are four structural frames in the north-south direction. These frames have structural elevations similar to frame A-A shown in Figure 2. There are three structural frames in the east-west directions. These frames have structural elevations similar to frame B-B shown in Figure 3. The building has a roof truss, which is shown in Figures 2 and 3. Frame A-A is a braced frame, where all members are connected using pin/hinge connections. Diagonal bracing members are needed for stability. Frame B-B is a moment frame, where all members are connected using fix/moment connections. There is no need for diagonal bracing members. The north-south and east-west frames resist the vertical gravity loads together. The three moment frames in the east-west direction resist the horizontal lateral loads in the east-west direction.
Z Y X
Z Y
Z Y X
Y X
Z X
ELEVATION OF BRACED FRAME
Z Y
ELEVATION OF MOMENT FRAME
Y X
PLAN OF ROOF TRUSS
ELEVATION OF BRACED FRAME
ELEVATION OF MOMENT FRAME
PLAN OF ROOF TRUSS
Z
X
Z
X
W
Y
Z
X
The four braced frames in the north-south direction resist the horizontal lateral loads in the north-south direction.
1.4 STRUCTURAL MEMBERS Structural members are categorized based up on the internal forces in them. For example: Tension member subjected to tensile axial force only Column or compression member subjected to compressive axial force only Tension/Compression member subjected to tensile/compressive axial forces Beam member subjected to flexural loads, i.e., shear force and bending moment only. The axial force in a beam member is negligible. Beam-column member member subjected to combined axial force and flexural loads (shear force, and bending moments)
In basic structural analysis (CE305) students have come across two types of structures, namely, trusses and frames. For example, Figure 2 shows a roof truss supported by a braced frame. All the members of a truss are connected using pin/hinge connections. All external forces are applied at the pins/hinges. As a result, all truss members are subjected to axial forces (tension or compression) only. In braced and moment frames, the horizontal members (beams) are subjected to flexural loads only. In braced frames, the vertical members (columns) are subjected to compressive axial forces only. In braced frames, the diagonal members (braces) are subjected to tension/compression axial forces only. In moment frames, the vertical members (beam-columns) are subjected to combined axial and flexural loads.
For practice, let us categorize the member shown in Figures 2 and 3.

R S E T J I P Q O
10 ft.
12 ft.
D N
12 ft.
C H M
12 ft.
B
15 ft.
A F K
25 ft.
25 ft.
Figure 2. Structural elevation of frame A-A
n m l
u t s
b1 a1 z
35 ft.
35 ft.
35 ft.
Figure 3. Structural elevation of frame B-B
1.5 STRUCTURAL CONNECTIONS Members of a structural frame are connected together using connections. Prominent connection types include: (1) truss / bracing member connections; (2) simple shear connections; (3) fully-restrained moment connections; and (4) partially-restrained flexible moment connections. Truss / bracing member connections are used to connect two or more truss members together. Only the axial forces in the members have to be transferred through the connection for continuity. Simple shear connections are the pin connections used to connect beam to column members. Only the shear forces are transferred through the connection for continuity. The bending moments are not transferred through the connection. Moment connections are fix connections used to connect beam to column members. Both the shear forces and bending moments are transferred through the connections with very small deformations (full restraint). Partially restrained connections are flexible connections used to connect beam to column members. The shear forces are transferred fully through the connection. However, the bending moment is only transferred partially.
S Gusset
Figure 4. Truss connection at S in Frame A-A.
Bracing member
Beam
Beam
Bracing member
Figure 5. Bracing connection and Simple Shear Connection at G in Frame A-A.
Beam
Column
Figure 6. All-bolted double angle shear connection.
Bevel Full penetration groove weld Field welding Weld access hole back-up bar
Beam
fillet welds shear tabs
Column
Figure 7. Directly welded flange fully restrained moment connection.
Figure 4 shows an example truss connection. Figure 5 shows an example bracing connection. Figure 6 shows an example shear connection. Figure 7 shows an example moment connection.
Connections are developed using bolts or welds. Bolts are used to connect two or more plate elements that are in the same plane. Boltholes are drilled in the plate elements. The threaded bolt shank passes through the holes, and the connection is secured using nuts.
Bolts are usually made of higher strength steel. Welds can be used to connect plate elements that are in the same or different planes. A high voltage electric arc is developed between the two plate elements. The electric arc causes localized melting of the base metal (plate element) and the weld electrode. After cooling, all the molten metal (base and weld) solidifies into one continuum. Thus, developing a welded connection.
In Figure 4, all the truss members are connected together by welding to a common gusset plate. The axial forces in the members are transferred through the gusset plates. This same connection can also be developed using bolts. How?
In Figure 5, the bracing members are connected to gusset plates, which are also connected to the beam and column. The bracing member can be connected to the gusset plate using bolts or welds. However, the gusset plate has to be welded to the beam / column.
In Figure 6, two angles are bolted to the web of the beam. The perpendicular legs of the angles are bolted to the flange of the column. Thus, an all-bolted double-angle shear connection is achieved. This all-bolted connection will be easier to assemble in the field as compared to welding. How is this a shear connection?
In Figure 7, the beam flanges are beveled and welded directly to the flange of column using full penetration groove welds. This welding will have to be done in the field during erection and it will require the use of back-up bars. Weld-access holes and skilled welders are required to achieve a weld of acceptable quality.
In Figure 7, the beam web is bolted to a shear tab (plate), which is fillet welded to the column in the shop. This shear tab connection transfers the shear from the beam to the column. How is Figure 7 a moment connection? 10
1.6 Structural Loads The building structure must be designed to carry or resist the loads that are applied to it over its design-life. The building structure will be subjected to loads that have been categorized as follows: Dead Loads (D): are permanent loads acting on the structure. These include the self-weight of structural and non-structural components. They are usually gravity loads. Live Loads (L): are non-permanent loads acting on the structure due to its use and occupancy. The magnitude and location of live loads changes frequently over the design life. Hence, they cannot be estimated with the same accuracy as dead loads. Wind Loads (W): are in the form of pressure or suction on the exterior surfaces of the building. They cause horizontal lateral loads (forces) on the structure, which can be critical for tall buildings. Wind loads also cause uplift of light roof systems. Snow Loads (S): are vertical gravity loads due to snow, which are subjected to variability due to seasons and drift. Roof Live Load (Lr): are live loads on the roof caused during the design life by planters, people, or by workers, equipment, and materials during maintenance. Values of structural loads are given in the publication ASCE 7-98: Minimum Design Loads for Buildings and Other Structures. The first phase of structural design consists of estimating the loads acting on the structure. This is done using the load values and combinations presented in ASCE 7-98 as explained in the following sub-sections.
11
1.6.1 Step I. Categorization of Buildings Categories I, II, III, and IV. See Table 1.1 below and in ASCE 7-98.
12
1.6.2 Dead Loads (D) Dead loads consist of the weight of all materials of construction incorporated into the building including but not limited to walls, floors, roofs, ceilings, stairways, built-in partitions, finishes, cladding and other similarly incorporated architectural and structural items, and fixed service equipment such as plumbing stacks and risers, electrical feeders, and heating, ventilating, and air conditioning systems. In some cases, the structural dead load can be estimated satisfactorily from simple formulas based in the weights and sizes of similar structures. For example, the average weight of steel framed buildings is 60-75 lb/ft2, and the average weight for reinforced concrete buildings is 110 130 lb/ft2. From an engineering standpoint, once the materials and sizes of the various components of the structure are determined, their weights can be found from tables that list their densities. See Tables 1.2 and 1.3, which are taken from Hibbeler, R.C. (1999), Structural Analysis, 4th Edition.
13
1.6.3 Live Loads Building floors are usually subjected to uniform live loads or concentrated live loads. They have to be designed to safely support the minimum uniformly distributed load or the minimum concentrated live load values given in the ASCE 7-98 (see Table 1.4 below), whichever produces the maximum load effects in the structural members.
14
15
The minimum uniformly distributed live loads (Lo) given in Table 1.4 above can be reduced for buildings with very large floor areas, because it is unlikely that the prescribed live load will occur simultaneously throughout the entire structure.
Equation (1.1) can be used to calculate the reduce uniformly distributed live load (L) 4.57 L = L o 0.25 + K LL A T (1.1)
where, AT is the tributary area in ft2 and KLL is the live load element factor as follows: KLL is equal to 4.0 for interior columns and exterior columns without cantilever slabs. KLL is equal to 3.0 for edge columns with cantilever slabs. KLL is equal to 2.0 for corner columns with cantilever slabs, edge beams without cantilever slabs, and interior beams. KLL is equal to 1.0 for all other members not identified above. Some limitations to the live load reduction are as follows: L cannot be less than 0.5Lo for members supporting one floor and L cannot be less that 0.4Lo for members supporting two or more floors. Live loads that exceed 100 lb/ft2 shall not be reduced except the live loads for members supporting two or more floors may be reduced by 20%. Live loads exceeding 100 lb/ft2 shall not be reduced for passenger car garages, public assembly occupancies, or roofs
16
1.6.4 Roof Live Loads Ordinary flat, pitched, and curved roofs shall be designed for the live loads specified in Equation 1.2 (from ASCE 7-98). Lr = 20 R1 R2 where, Lr is the roof live load per square foot of horizontal projection in psf. =1 R1 = 1.2 - 0.001 AT = 0.6 for AT 200 ft2 for 200 < AT < 600 ft2 for 600ft2 AT where, 12 Lr 20 (1.2)
____________________________________________________________________
=1 R2 = 1.2 - 0.05 F = 0.6
for F 4 for 4 < F < 12 for 12 F
where, F = no. of inches of rise per foot for pitched roof.
17
1.6.5 Wind Loads Design wind loads for buildings can be based on: (a) simplified procedure; (b) analytical procedure; and (c) wind tunnel or small-scale procedure. Refer to ASCE 7-98 for the simplified procedure. This simplified procedure is applicable only to buildings with mean roof height less than 30 ft. The wind tunnel procedure consists of developing a small-scale model of the building and testing it in a wind tunnel to determine the expected wind pressures etc. It is expensive and may be utilized for difficult or special situations. The analytical procedure is used in most design offices. It is fairly systematic but somewhat complicated to account for the various situations that can occur: Wind velocity will cause pressure on any surface in its path. The wind velocity and hence the velocity pressure depend on the height from the ground level. Equation 1.3 is recommended by ASCE 7-98 for calculating the velocity pressure (qz) in lb/ft2 qz = 0.00256 Kz Kzt Kd V2 I where, V is the wind velocity Kd is a directionality factor Kzt is a topographic factor I is the importance factor (see Figure 6-1 in ASCE 7-98) (=0.85 for CE 405) (= 1.0 for CE 405) (=1.0 for CE 405) (lb/ft2) (1.3)
Kz varies with height z above the ground level (see Table 6-5 in ASCE 7-98) A significant portion of the U.S. including Lansing has V = 90 mph. At these location qz = 17.625 Kz (lb/ft2) (1.4)
18
The velocity pressure qz is used to calculate the design wind pressure (p) for the building structure as follows: p = q GCp qi (GCpi) (lb/ft2) (1.5)
where, G = gust effect factor (=0.85 for CE 405) Cp = external pressure coefficient from Figure 6-3 in ASCE 7-98 Cpi = internal pressure coefficient from Table 6-7 in ASCE 7-98 q depends on the orientation of the building wall or roof with respect to direction of the wind as follows: q = qz for the windward wall varies with height z q = qh for leeward wall. qh is qz evaluated at z = h (mean height of building). qh is constant. qi = qh for windward, leeward, side walls and roofs.
Note that a positive sign indicates pressure acting towards a surface. Negative sign indicate pressure away from the surface
Equation 1.5 indicates that the design wind pressure p consists of two components: (1) the external pressure on the building (q GCp); and (2) the internal pressure in the building (qh GCpi)
1.6.6 Load and Resistance Factor Design The load and resistance factor design approach is recommended by AISC for designing steel structures. It can be understood as follows: Step I. Determine the ultimate loads acting on the structure The values of D, L, W, etc. given by ASCE 7-98 are nominal loads (not maximum or ultimate)
19
During its design life, a structure can be subjected to some maximum or ultimate loads caused by combinations of D, L, or W loading.
The ultimate load on the structure can be calculated using factored load combinations, which are given by ASCE and AISC (see pages 2-10 and 2-11 of AISC manual). The most relevant of these load combinations are given below: 1.4 D 1.2 D + 1.6 L + 0.5 (Lr or S) 1.2 D + 1.6 (Lr or S) + (0.5 L or 0.8 W) 1.2 D + 1.6 W + 0.5 L + 0.5 (Lr or S) 0.9 D + 1.6 W (4.2 1) (4.2 2) (4.2 3) (4.2 4) (4.2 5)
Step II. Conduct linear elastic structural analysis Determine the design forces (Pu, Vu, and Mu) for each structural member
Step III. Design the members The failure (design) strength of the designed member must be greater than the corresponding design forces calculated in Step II. See Equation (4.3) below:
Rn >
-
i Qi
(4.3)
Where, Rn is the calculated failure strength of the member
is the resistance factor used to account for the reliability of the material behavior and
equations for Rn
Qi is the nominal load i is the load factor used to account for the variability in loading and to estimate the ultimate loading condition.
20
Example 1.1 Consider the building structure with the structural floor plan and elevation shown below. Estimate the wind loads acting on the structure when the wind blows in the east-west direction. The structure is located in Lansing.
gi hi ii 25 ft. di N
ei
fi
25 ft. ai 50 ft.
bi 50 ft.
ci
Figure 8. Structural floor plan

10 ft. 10 ft. 10 ft. 10 ft. 10 ft.
a1 b1 c1 a6 a5 a4 a3 a2 b6 b5 b4 b3 b2 c6 c5 c4 c3 c2
15 ft.
Figure 9. Structural elevation in east-west direction
21
10 10
b6 b5 b4
e6 e5 e4 e3 e2 e1
h6 h5 h4 h3 h2 h1 N
10 b3 10 b2 10 b1 15
Figure 10. Structural elevation in north-south direction Velocity pressure (qz) Kd = directionality factor = 0.85 Kzt = topographic factor = 1.0 I = importance factor = 1.0 Kh values for Exposure B, Case 2 Kh 0.62 0.66 0.70 0.76 0.81 0.85 0.89 z 15 - 20 20 25 25 30 30 40 40 50 50 60 60 - 70
0.57 0 - 15
qz = 0.00256 Kz Kzt Kd V2I In Lansing V = 90 mph
22
qz = 17.625 Kz psf
Wind pressure (p) Gust factor = G = 0.85 For wind in east west direction; L/B = Length / width = 2.0 External pressure coefficient = Cp = +0.8 for windward walls Cp = -0.3 for leeward walls Cp = -0.7 for side walls External pressure = q G Cp External pressure on windward wall = qz GCp = 17.625 Kz x 0.85 x 0.8 = 11.99 Kz psf toward surface External pressure on leeward wall = qh GCp = 17.625 K65 x 0.85 x (-0.3) = 4.00 psf away from surface External pressure on side wall = qh GCp =17.625 K65 x 0.85 x (-0.7) = 9.33 psf away from surface The external pressures on the structure are shown in Figures 11 and 12 below.
Figure 11. External pressures on structural plan
23
Figure 12. External pressure on structural elevation (east west) Internal pressure p = q GCp qi GCpi qi = qh = 17.625 K65 = 17.625 x 0.89 = 15.69 psf Enclosed building; GCpi = +0.18 (acting toward surface) GCpi = -0.18 (acting away from surface) qi GCpi = 2.82 psf acting toward or away from surface See Figure 13 (a) and (b) below (a) (b)
Figure 13. Internal pressure seen in structural plan Take the external pressure from Figure 11 and 12 and add to internal pressure from Figures 13 (a) and (b) to obtain the final pressure diagrams. Adding the internal pressure will not change the lateral forces in the structure.
24
(a)
(b)
Figure 14. Resultant wind pressure diagrams including external and internal pressures Note: According to ASCE 7-98, the minimum wind design loading is equal to 10 lb/ft2 multiplied by the area of the building projected on a vertical plane normal to assumed wind direction. The determined design wind loading is greater than the minimum value. Therefore, continue with estimated design wind loading.
Example 1.2 Determine the magnitude and distribution of live loading on the north-south frame bi - ei - hi Step I: Determine relevant tributary and influence areas. Estimate live load reduction factors.
gi hi ii 25 ft.
1 di 3 ei 2 4 fi
25 ft.
ai 50 ft.
bi 50 ft.
ci
25
Table 1.1 Member tributary areas and minimum design live loading. Member Tributary area bi-ei AT2 = x 25.0 x 12.5 x 2 = 312.5 ft2 ei - hi AT1 = x 25.0 x 12.5 x 2 = 312.5 ft2 di - ei AT3 = x 12.5 x 25.0 x 2 + 2.0 25.0 x 25.0 = 937.5 ft2 ei - fi AT4 = x 12.5 x 25.0 x 2 + 2.0 25.0 x 25.0 = 937.5 ft2 bi ei hi 12.5 x 50.0 = 625.0 ft2 25.0 x 50.0 = 1250.0 ft2 12.5 x 50.0 = 625 ft
2
KLL Lo/L=0.25 + 4.57/(KLLAT)0.5 Lo/L min. 2.0 2.0 0.4328 0.4328 0.36 0.36 0.34 0.3146 0.34 0.5 0.5 0.5 0.5 0.4 0.4 0.4
4.0 4.0 4.0
Step II. Estimate uniformly distributed loads

b6 b5 b4 b3 b2 b1 e6 e5 e4 e3 e2 e1 g6 g5 g4 g3 g2 g1
26
Step III: Estimate live loading on columns from other frames than the one being investigated.
d6 d5 d4 d3 d2 d1
e6 e5 e4 e3 e2 e1
Resultant
f6 f5 f4 f3 f2 f1
Note: The minimum reduced live load for the column ei from Table 1 = 0.40 Lo. However, the live loading on column ei is being estimated using the reduced live loading on the beams. For consistency, make sure that the reduced beam live loading is not less than the reduced column live loading.
Note: The wind pressures act on the sides of the building. The lateral forces acting on the frame are calculated using these wind pressures and the tributary area concept.
27
ASCE 7 98 pg. 39
28
Figure showing the Wind Speed of Eastern US. (ASCE 7 98 pg. 35)
29
ASCE 7 98 pg. 41
30
ASCE 7 98 pg. 43
31
ASCE 7 98 pg. 42
32
Importance factor ASCE 7 98 pg. 55
wind directionality factor asce 7 98 pg.
33
velocity pressure exposure coefficient
34
internal pressure coefficient for buildings
35
Chapter 2. Design of Beams Flexure and Shear 2.1 Section force-deformation response & Plastic Moment (Mp) A beam is a structural member that is subjected primarily to transverse loads and negligible axial loads. The transverse loads cause internal shear forces and bending moments in the beams as shown in Figure 1 below.
w P
V(x)
M(x)
Figure 1. Internal shear force and bending moment diagrams for transversely loaded beams. These internal shear forces and bending moments cause longitudinal axial stresses and shear stresses in the cross-section as shown in the Figure 2 below.
d M(x) V(x) b
+d / 2 d / 2
dF = b dy
Curvature = = 2/d
F = b dy
M = b dy y (Planes remain plane)

d / 2
+d / 2
Figure 2. Longitudinal axial stresses caused by internal bending moment.
Steel material follows a typical stress-strain behavior as shown in Figure 3 below.
u y
Figure 3. Typical steel stress-strain behavior. If the steel stress-strain curve is approximated as a bilinear elasto-plastic curve with yield stress equal to y, then the section Moment - Curvature (M-) response for monotonically increasing moment is given by Figure 4.
Mp B My
Section Moment, M
C
y y
D
y y
E
y
y y
y 2y
y 5y
y 10y
2y
5y
10y
C Curvature,
A: Extreme fiber reaches y B: Extreme fiber reaches 2y C: Extreme fiber reaches 5y D: Extreme fiber reaches 10y E: Extreme fiber reaches infinite strain
Figure 4. Section Moment - Curvature (M-) behavior.
In Figure 4, My is the moment corresponding to first yield and Mp is the plastic moment capacity of the cross-section. The ratio of Mp to My is called as the shape factor f for the section. For a rectangular section, f is equal to 1.5. For a wide-flange section, f is equal to 1.1.
Calculation of Mp: Cross-section subjected to either +y or -y at the plastic limit. See Figure 5 below.
y
Plastic centroid.
A1
A2
y A 2
y1
y2
y A 1
y
(a) General cross-section (b) Stress distribution
F = y A1 y A 2 = 0 A1 = A 2 = A / 2 M = y A ( y1 + y 2 ) 2 Where , y1 = centroid of A1 y 2 = centroid of A 2
(c) Force distribution
(d) Equations Figure 5. Plastic centroid and Mp for general cross-section. The plastic centroid for a general cross-section corresponds to the axis about which the total area is equally divided, i.e., A1 = A2 = A/2 The plastic centroid is not the same as the elastic centroid or center of gravity (c.g.) of the cross-section.
As shown below, the c.g. is defined as the axis about which A1y1 = A2y2.
y2
A1, y1 y1 c.g. = elastic N.A. A , y 2 2
About the c.g. A 1 y 1 = A 2 y2
For a cross-section with at-least one axis of symmetry, the neutral axis corresponds to the centroidal axis in the elastic range. However, at Mp, the neutral axis will correspond to the plastic centroidal axis.
For a doubly symmetric cross-section, the elastic and the plastic centroid lie at the same point.
Mp = y x A/2 x (y1+y2) As shown in Figure 5, y1 and y2 are the distance from the plastic centroid to the centroid of area A1 and A2, respectively.
A/2 x (y1+y2) is called Z, the plastic section modulus of the cross-section. Values for Z are tabulated for various cross-sections in the properties section of the LRFD manual.
Mp = 0.90 Z Fy
where,
- See Spec. F1.1
Mp = plastic moment, which must be 1.5 My for homogenous cross-sections My = moment corresponding to onset of yielding at the extreme fiber from an elastic stress distribution = Fy S for homogenous cross-sections and = Fyf S for hybrid sections. Z = plastic section modulus from the Properties section of the AISC manual. S = elastic section modulus, also from the Properties section of the AISC manual.
Example 2.1 Determine the elastic section modulus, S, plastic section modulus, Z, yield moment, My, and the plastic moment Mp, of the cross-section shown below. What is the design moment for the beam cross-section. Assume 50 ksi steel.
12 in. F1 W t = 0.5 in. w F2 15 in.
1.0 in. 0.75 in.
16 in.
Ag = 12 x 0.75 + (16 - 0.75 - 1.0) x 0.5 + 15 x 1.0 = 31.125 in2 Af1 = 12 x 0.75 = 9 in2 Af2 = 15 x 1.0 = 15.0 in2 Aw = 0.5 x (16 - 0.75 - 1.0) = 7.125 in2
distance of elastic centroid from bottom = y
9 (16 0.75 / 2) + 7.125 8.125 + 15 0.5 = 6.619 in. 31.125 Ix = 12 0.753/12 + 9.0 9.0062 + 0.5 14.253/12 + 7.125 1.5062 + 15.0 13/12 + y= 15 6.1192 = 1430 in4 Sx = Ix / (16-6.619) = 152.43 in3 My-x = Fy Sx = 7621.8 kip-in. = 635.15 kip-ft.
distance of plastic centroid from bottom = y p

15.0 1.0 + 0.5 ( y p 1.0) = y p = 2.125 in. 31.125 = 15.5625 2
y1=centroid of top half-area about plastic centroid =
9 13.5 + 6.5625 6.5625 = 10.5746 in. 15.5625
y2=centroid of bottom half-area about plas. cent. =
0.5625 0.5625 + 15.0 1.625 = 1.5866 in. 15.5625
Zx = A/2 x (y1 + y2) = 15.5625 x (10.5746 + 1.5866) = 189.26 in3 Mp-x = Zx Fy = 189.26 x 50 = 9462.93 kip-in. = 788.58 kip-ft.
Design strength according to AISC Spec. F1.1= bMp= 0.9 x 788.58 = 709.72 kip-ft. Check = Mp 1.5 My Therefore, 788.58 kip-ft. < 1.5 x 635.15 = 949.725 kip-ft. - OK!
Reading Assignment
2.2 Flexural Deflection of Beams Serviceability
Steel beams are designed for the factored design loads. The moment capacity, i.e., the factored moment strength (bMn) should be greater than the moment (Mu) caused by the factored loads. A serviceable structure is one that performs satisfactorily, not causing discomfort or perceptions of unsafety for the occupants or users of the structure. For a beam, being serviceable usually means that the deformations, primarily the vertical slag, or deflection, must be limited. The maximum deflection of the designed beam is checked at the service-level loads. The deflection due to service-level loads must be less than the specified values. The AISC Specification gives little guidance other than a statement in Chapter L, Serviceability Design Considerations, that deflections should be checked. Appropriate limits for deflection can be found from the governing building code for the region. The following values of deflection are typical maximum allowable total (service dead load plus service live load) deflections.
Plastered floor construction L/360 Unplastered floor construction L/240 Unplastered roof construction L/180
In the following examples, we will assume that local buckling and lateral-torsional buckling are not controlling limit states, i.e, the beam section is compact and laterally supported along the length.
Example 2.2 Design a simply supported beam subjected to uniformly distributed dead load of 450 lbs/ft. and a uniformly distributed live load of 550 lbs/ft. The dead load does not include the self-weight of the beam.
Step I. Calculate the factored design loads (without self-weight).
wU = 1.2 wD + 1.6 wL = 1.42 kips / ft. MU = wu L2 / 8 = 1.42 x 302 / 8 = 159.75 kip-ft.

Step II. Select the lightest section from the AISC Manual design tables.
From page
of the AISC manual, select W16 x 26 made from 50 ksi steel with
bMp = 166.0 kip-ft.

Step III. Add self-weight of designed section and check design
wsw = 26 lbs/ft Therefore, wD = 476 lbs/ft = 0.476 lbs/ft. wu = 1.2 x 0.476 + 1.6 x 0.55 = 1.4512 kips/ft. Therefore, Mu = 1.4512 x 302 / 8 = 163.26 kip-ft. < bMp of W16 x 26.
OK! Step IV. Check deflection at service loads.
w = 0.45 + 0.026 + 0.55 kips/ft. = 1.026 kips/ft.
= 5 w L4 / (384 E Ix) = 5 x (1.026/12) x (30 x 12)4 / (384 x 29000 x 301) = 2.142 in. > L/360
- for plastered floor construction
Step V. Redesign with service-load deflection as design criteria
L /360 = 1.0 in. > 5 w L4/(384 E Ix) Therefore, Ix > 644.8 in4
Select the section from the moment of inertia selection tables in the AISC manual. See page select W21 x 44.
W21 x 44 with Ix = 843 in4 and bMp = 358 kip-ft. (50 ksi steel).
Deflection at service load = = 0.765 in. < L/360
- OK!
Note that the serviceability design criteria controlled the design and the section Example 2.3 Design the beam shown below. The unfactored dead and live loads are shown in
the Figure.
10 kips (live load)
0.67 k/ft. (dead load) 0.75 k/ft. (live load)
15 ft.
30 ft.
Step I. Calculate the factored design loads (without self-weight).
wu = 1.2 wD + 1.6 wL = 1.2 x 0.67 + 1.6 x 0.75 = 2.004 kips / ft. Pu = 1.2 PD + 1.6 PL = 1.2 x 0 + 1.6 x 10 = 16.0 kips Mu = wU L2 / 8 + PU L / 4 = 225.45 + 120 = 345.45 kip-ft.
Step II. Select the lightest section from the AISC Manual design tables.
From page ____________ of the AISC manual, select W21 x 44 made from 50 ksi steel with
bMp = 358.0 kip-ft.

Self-weight = wsw = 44 lb/ft.
Step III. Add self-weight of designed section and check design
wD = 0.67 + 0.044 = 0.714 kips/ft wu = 1.2 x 0.714 + 1.6 x 0.75 = 2.0568 kips/ft. Therefore, Mu = 2.0568 x 302 / 8 + 120 = 351.39 kip-ft. < bMp of W21 x 44.
OK! Step IV. Check deflection at service loads.
Service loads
Distributed load = w = 0.714 + 0.75 = 1.464 kips/ft. Concentrated load = P = D + L = 0 + 10 kips = 10 kips
Deflection due to uniform distributed load = d = 5 w L4 / (384 EI) Deflection due to concentrated load = c = P L3 / (48 EI)
Therefore, service-load deflection = = d + c
= 5 x 1.464 x 3604 / (384 x 29000 x 12 x 843) + 10 x 3603 / (48 x 29000 x 843) = 1.0914 + 0.3976 = 1.49 in.
Assuming unplastered floor construction, max = L/240 = 360/240 = 1.5 in. Therefore, < max
- OK!
10
2.3 Local buckling of beam section Compact and Non-compact
Mp, the plastic moment capacity for the steel shape, is calculated by assuming a plastic stress distribution (+ or - y) over the cross-section.
The development of a plastic stress distribution over the cross-section can be hindered by two different length effects: (1) Local buckling of the individual plates (flanges and webs) of the cross-section before they develop the compressive yield stress y. (2) Lateral-torsional buckling of the unsupported length of the beam / member before the cross-section develops the plastic moment Mp.
Figure 7. Local buckling of flange due to compressive stress ()
The analytical equations for local buckling of steel plates with various edge conditions and the results from experimental investigations have been used to develop limiting slenderness ratios for the individual plate elements of the cross-sections.
See Spec. B5 (page 16.1 12), Table B5.1 (16.1-13) and Page 16.1-183 of the AISC-manual Steel sections are classified as compact, non-compact, or slender depending upon the slenderness () ratio of the individual plates of the cross-section. 11
Compact section if all elements of cross-section have p Non-compact sections if any one element of the cross-section has p r Slender section if any element of the cross-section has r
It is important to note that: If p, then the individual plate element can develop and sustain y for large values of
before local buckling occurs.

If p r, then the individual plate element can develop y but cannot sustain it before local buckling occurs. If r , then elastic local buckling of the individual plate element occurs.
Co mpressive axial stress,
Compact
Non-Compact Slender
Effective axial strain,
Figure 8. Stress-strain response of plates subjected to axial compression and local buckling.
Thus, slender sections cannot develop Mp due to elastic local buckling. Non-compact sections can develop My but not Mp before local buckling occurs. Only compact sections can develop the plastic moment Mp.
All rolled wide-flange shapes are compact with the following exceptions, which are noncompact.
12
W40x174, W14x99, W14x90, W12x65, W10x12, W8x10, W6x15 (made from A992)
The definition of and the values for p and r for the individual elements of various crosssections are given in Table B5.1 and shown graphically on page 16.1-183. For example,
Section
Plate element
bf/2tf h/tw bf/tf h/tw (b-3t)/t (b-3t)/t 0.38 3.76 0.38 3.76 1.12 3.76
p
E / Fy
r
0.38 5.70 0.38 5.70 1.40 5.70
E / FL E / Fy E / FL E / Fy E / Fy E / Fy
Wide-flange
Flange Web
E / Fy E / Fy E / Fy E / Fy E / Fy
Channel
Flange Web
Square or Rect. Box
Flange Web
In CE405 we will design all beam sections to be compact from a local buckling standpoint
13
2.4 Lateral-Torsional Buckling
The laterally unsupported length of a beam-member can undergo lateral-torsional buckling due to the applied flexural loading (bending moment).
(a) M
(b)
M M
Figure 9. Lateral-torsional buckling of a wide-flange beam subjected to constant moment.
14
Lateral-torsional buckling is fundamentally similar to the flexural buckling or flexuraltorsional buckling of a column subjected to axial loading. The similarity is that it is also a bifurcation-buckling type phenomenon. The differences are that lateral-torsional buckling is caused by flexural loading (M), and the buckling deformations are coupled in the lateral and torsional directions.
There is one very important difference. For a column, the axial load causing buckling remains constant along the length. But, for a beam, usually the lateral-torsional buckling causing bending moment M(x) varies along the unbraced length.
The worst situation is for beams subjected to uniform bending moment along the unbraced length. Why?
2.4.1 Lateral-torsional buckling Uniform bending moment
Consider a beam that is simply-supported at the ends and subjected to four-point loading as shown below. The beam center-span is subjected to uniform bending moment M. Assume that lateral supports are provided at the load points.
Lb
Laterally unsupported length = Lb. If the laterally unbraced length Lb is less than or equal to a plastic length Lp then lateral torsional buckling is not a problem and the beam will develop its plastic strength Mp.
Lp = 1.76 ry x
E / Fy
- for I members & channels (See Pg. 16.1-33)
15
If Lb is greater than Lp then lateral torsional buckling will occur and the moment capacity of the beam will be reduced below the plastic strength Mp as shown in Figure 10 below.
Mn = Mp Zx Fy = Mp Sx (Fy 10) = Mr
Moment Capacity, M n
Lb L p M n = M p ( M p M r ) L L r p Mn =
2 EI y
L2 b
GJ +
2 ECw
L2 b
Lp
Lr Unbraced length, Lb
Figure 10. Moment capacity (Mn) versus unsupported length (Lb).
As shown in Figure 10 above, the lateral-torsional buckling moment (Mn = Mcr) is a function of the laterally unbraced length Lb and can be calculated using the equation:
Mn = Mcr = Lb E E Iy G J + L Iy Cw b
2
where,
Mn = moment capacity Lb = laterally unsupported length. Mcr = critical lateral-torsional buckling moment. E = 29000 ksi; G = 11,200 ksi
Iy = moment of inertia about minor or y-axis (in4) J = torsional constant (in4) from the AISC manual pages _______________. Cw = warping constant (in6) from the AISC manual pages _______________.
16
This equation is valid for ELASTIC lateral torsional buckling only (like the Euler equation). That is it will work only as long as the cross-section is elastic and no portion of the crosssection has yielded.
As soon as any portion of the cross-section reaches the yield stress Fy, the elastic lateral torsional buckling equation cannot be used. Lr is the unbraced length that corresponds to a lateral-torsional buckling moment Mr = Sx (Fy 10). Mr will cause yielding of the cross-section due to residual stresses.
When the unbraced length is less than Lr, then the elastic lateral torsional buckling equation cannot be used.
When the unbraced length (Lb) is less than Lr but more than the plastic length Lp, then the lateral-torsional buckling Mn is given by the equation below: If Lp Lb Lr,
Lb L p then M n = M p ( M p M r ) L L r p
This is linear interpolation between (Lp, Mp) and (Lr, Mr) See Figure 10 again.
17
2.4.2 Moment Capacity of beams subjected to non-uniform bending moments
As mentioned previously, the case with uniform bending moment is worst for lateral torsional buckling.
For cases with non-uniform bending moment, the lateral torsional buckling moment is
greater than that for the case with uniform moment.
The AISC specification says that: The lateral torsional buckling moment for non-uniform bending moment case = Cb x lateral torsional buckling moment for uniform moment case.
Cb is always greater than 1.0 for non-uniform bending moment.
Cb is equal to 1.0 for uniform bending moment.
Sometimes, if you cannot calculate or figure out Cb, then it can be conservatively assumed as 1.0.
Cb =
2.5 M max
12.5 M max + 3 MA + 4 MB + 3 Mc
where, Mmax = magnitude of maximum bending moment in Lb

MA = magnitude of bending moment at quarter point of Lb MB = magnitude of bending moment at half point of Lb MC = magnitude of bending moment at three-quarter point of Lb
The moment capacity Mn for the case of non-uniform bending moment Mn = Cb x {Mn for the case of uniform bending moment} Mp Important to note that the increased moment capacity for the non-uniform moment case cannot possibly be more than Mp. Therefore, if the calculated values is greater than Mp, then you have to reduce it to Mp
18
Mp
Moment Capacity, Mn
Mr Cb = 1.5 Cb = 1.2 Cb = 1.0
Lp
Lr Unbraced length, Lb
Figure 11. Moment capacity versus Lb for non-uniform moment case. 2.5 Beam Design
Example 2.4 Design the beam shown below. The unfactored uniformly distributed live load is equal to 3 kips/ft. There is no dead load. Lateral support is provided at the end reactions.
wL = 3 kips/ft.
24 ft.
Lateral support / bracing
Step I. Calculate the factored loads assuming a reasonable self-weight.
Assume self-weight = wsw = 100 lbs/ft. Dead load = wD = 0 + 0.1 = 0.1 kips/ft. Live load = wL = 3.0 kips/ft. Ultimate load = wu = 1.2 wD + 1.6 wL = 4.92 kips/ft. Factored ultimate moment = Mu = wu L2/8 = 354.24 kip-ft.
19
Step II. Determine unsupported length Lb and Cb
There is only one unsupported span with Lb = 24 ft. Cb = 1.14 for the parabolic bending moment diagram, See values of Cb shown in Figure.
Step III. Select a wide-flange shape
The moment capacity of the selected section bMn > Mu
(Note b = 0.9)
bMn = moment capacity = Cb x (bMn for the case with uniform moment) bMp
Pages _________________ in the AISC-LRFD manual, show the plots of bMn-Lb for the case of uniform bending moment (Cb=1.0) Therefore, in order to select a section, calculate Mu/Cb and use it with Lb to find the first section with a solid line as shown in class. Mu/Cb = 354.24/1.14 = 310.74 kip-ft. Select W16 x 67 (50 ksi steel) with bMn =357 kip-ft. for Lb = 24 ft. and Cb =1.0 For the case with Cb = 1.14,
bMn = 1.14 x 357 = 406.7 kip-ft., which must be bMp = 491 kip-ft.
OK!
Thus, W16 x 67 made from 50 ksi steel with moment capacity equal to 406.7 kip-ft. for an unsupported length of 24 ft. is the designed section.
Step IV. Check for local buckling.
= bf / 2tf = 7.7; Corresponding p = 0.38 (E/Fy)0.5 = 9.192

Therefore, < p - compact flange
= h/tw = 34.4; Corresponding p = 3.76 (E/Fy)0.5 = 90.5

Therefore, < p Compact section. - compact web - OK!
This example demonstrates the method for designing beams and accounting for Cb > 1.0 20
Example 2.5 Design the beam shown below. The concentrated live loads acting on the beam are shown in the Figure. The beam is laterally supported at the load and reaction points.
30 kips 30 kips
wsw = 0.1 kips/ft.
12 ft.
8 ft.
10 ft.
30 ft.
Lateral support / bracing
Step I. Assume a self-weight and determine the factored design loads
Let, wsw = 100 lbs/ft. = 0.1 kips/ft. PL = 30 kips Pu = 1.6 PL = 48 kips wu = 1.2 x wsw = 0.12 kips/ft. The reactions and bending moment diagram for the beam are shown below.
48 kips wsw = 0.12 kips/ft. A B 12 ft. 46.6 kips A B C 8 ft. C 10 ft. 53 kips D D 48 kips
550.6 kip-ft.
524 kip-ft.
Step II. Determine Lb, Cb, Mu, and Mu/Cb for all spans.
21
Span AB BC CD
Lb (ft.) 12
Cb
1.67 1.0 (assume) 1.67
Mu (kip-ft.) 550.6
Mu/Cb (kip-ft.) 329.7
8 10
550.6 524.0
550.6 313.8
It is important to note that it is possible to have different Lb and Cb values for different laterally unsupported spans of the same beam.
Step III. Design the beam and check all laterally unsupported spans
Assume that span BC is the controlling span because it has the largest Mu/Cb although the corresponding Lb is the smallest.
From the AISC-LRFD manual select W21 x 68 made from 50 ksi steel (page _____)
Check the selected section for spans AB, BC, and CD

Span Lb (ft.)
AB BC CD
12 8 10
bM n for Cb = 1.0 from ______ 507

572 540
Cb
1.67 1.0 1.67
bM n for Cb value col. 3 x col. 4 846.7

572.0 901.8 - OK! -OK! -OK!
bM p
limit 600 kip-ft
600 kip-ft.
Thus, for span AB, bMn = 600 kip-ft. > Mu for span BC, bMn = 572.0 kip-ft. > Mu For span CD, bMn = 600 kip-ft. > Mu
22
Step IV. Check for local buckling
= bf / 2tf = 6.0; Corresponding p = 0.38 (E/Fy)0.5 = 9.192

Therefore, < p - compact flange
= h/tw = 43.6; Corresponding p = 3.76 (E/Fy)0.5 = 90.55

Therefore, < p Compact section. - compact web - OK!
This example demonstrates the method for designing beams with several laterally unsupported spans with different Lb and Cb values.
Example 2.6
Design the simply-supported beam shown below. The uniformly distributed dead load is equal to 1 kips/ft. and the uniformly distributed live load is equal to 2 kips/ft. A concentrated live load equal to 10 kips acts at the mid-span. Lateral supports are provided at the end reactions and at the mid-span.
wD = 1.0 kips/ft. wL = 2.0 kips/ft. A B 12 ft.
10 kips
12 ft.
Step I. Assume the self-weight and calculate the factored design loads.
Let, wsw = 100 lbs/ft. = 0.1 kips/ft. wD = 1+ 0.1 = 1.1 kips/ft. wL = 2.0 kips/ft. wu = 1.2 wD + 1.6 wL = 4.52 kips/ft. Pu = 1.6 x 10 = 16.0 kips 23
The reactions and the bending moment diagram for the factored loads are shown below.
16 kips wu = 4.52 kips/ft. B 12 ft. 62.24 kips x M(x) = 62.24 x - 4.52 x2 /2 12 ft. 62.24 kips
Step II. Calculate Lb and Cb for the laterally unsupported spans.
Since this is a symmetric problem, need to consider only span AB Lb = 12 ft.; C b =

12.5 M max 2.5 M max + 3 M A + 4 M B + 3 M c
M(x) = 62.24 x 4.52 x2/2 Therefore, MA = M(x = 3 ft.) = 166.38 kip-ft. MB = M(x = 6 ft.) = 292.08 kip-ft. MC = M(x = 9ft.) = 377.1 kip-ft Mmax = M(x = 12 ft.) = 421.44 kip-ft. Therefore, Cb = 1.37
Step III. Design the beam section
- quarter-point along Lb = 12 ft. - half-point along Lb = 12 ft. -three-quarter point along Lb= 12 ft. - maximum moment along Lb =12ft.
Mu = Mmax = 421.44 kip-ft. Lb = 12.0 ft.; Cb = 1.37 Mu/Cb = 421.44/1.37 = 307.62 kip-ft. Select W21 x 48 made from 50 ksi with bMn = 322 kip-ft. for Lb = 12.0 ft. and Cb =1.0 For Cb = 1.37, bMn = _441.44 k-ft., but must be < or = bMp = 398 k-ft.
24
Therefore, for Cb =1.37, bMn = 398 k-ft. < Mu
Step IV. Redesign the section
Select the next section with greater capacity than W21 x 48 Select W18 x 55 with bMn = 345 k-ft. for Lb = 12 ft. and Cb = 1.0 For Cb = 1.37, bMn = 345 x 1.37 = 472.65 k-ft. but must be bMp = 420 k-ft. Therefore, for Cb = 1.37, bMn = 420 k-ft., which is < Mu (421.44 k-ft), (NOT OK!)
Select W 21 x 55 with bMn = 388 k-ft. for Lb = 12 ft. and Cb = 1.0 For Cb 1.37, bMn = 388 x 1.37 = 531.56 k-ft., but must be bMp = 473 k-ft. Therefore, for Cb = 1.37, bMn = 473 k-ft, which is > Mu (421.44 k-ft). (OK!)
Step V. Check for local buckling.
= bf / 2tf = 7.87; Corresponding p = 0.38 (E/Fy)0.5 = 9.192 Therefore, < p - compact flange
= h/tw = 50.0; Corresponding p = 3.76 (E/Fy)0.5 = 90.55 Therefore, < p Compact section. - compact web
- OK!
This example demonstrates the calculation of Cb and the iterative design method.
25
CHAPTER 3. COMPRESSION MEMBER DESIGN 3.1 INTRODUCTORY CONCEPTS Compression Members: Structural elements that are subjected to axial compressive forces only are called columns. Columns are subjected to axial loads thru the centroid. Stress: The stress in the column cross-section can be calculated as
f =
P A
(2.1)
where, f is assumed to be uniform over the entire cross-section. This ideal state is never reached. The stress-state will be non-uniform due to: Accidental eccentricity of loading with respect to the centroid Member out-of straightness (crookedness), or Residual stresses in the member cross-section due to fabrication processes.
Accidental eccentricity and member out-of-straightness can cause bending moments in the member. However, these are secondary and are usually ignored.
Bending moments cannot be neglected if they are acting on the member. Members with axial compression and bending moment are called beam-columns.
3.2 COLUMN BUCKLING
Consider a long slender compression member. If an axial load P is applied and increased slowly, it will ultimately reach a value Pcr that will cause buckling of the column. Pcr is called the critical buckling load of the column.
(a)
Pcr
(b)
What is buckling?
Buckling occurs when a straight column subjected to axial compression suddenly undergoes bending as shown in the Figure 1(b). Buckling is identified as a failure limit-state for columns.
Pcr
Figure 1. Buckling of axially loaded compression members
The critical buckling load Pcr for columns is theoretically given by Equation (3.1) Pcr =
2 E I
( K L )2
(3.1)
where, I = moment of inertia about axis of buckling K = effective length factor based on end boundary conditions Effective length factors are given on page 16.1-189 of the AISC manual.
In examples, homeworks, and exams please state clearly whether you are using the theoretical value of K or the recommended design values.
EXAMPLE 3.1 Determine the buckling strength of a W 12 x 50 column. Its length is 20 ft. For
major axis buckling, it is pinned at both ends. For minor buckling, is it pinned at one end and fixed at the other end.
Solution Step I. Visualize the problem
Figure 2. (a) Cross-section; (b) major-axis buckling; (c) minor-axis buckling
For the W12 x 50 (or any wide flange section), x is the major axis and y is the minor axis. Major axis means axis about which it has greater moment of inertia (Ix > Iy)
Figure 3. (a) Major axis buckling; (b) minor axis buckling 4
Step II. Determine the effective lengths
According to Table C-C2.1 of the AISC Manual (see page 16.1 - 189): For pin-pin end conditions about the minor axis Ky = 1.0 (theoretical value); and Ky = 1.0 (recommended design value) For pin-fix end conditions about the major axis Kx = 0.7 (theoretical value); and Kx = 0.8 (recommended design value)
According to the problem statement, the unsupported length for buckling about the major (x) axis = Lx = 20 ft.
The unsupported length for buckling about the minor (y) axis = Ly = 20 ft. Effective length for major (x) axis buckling = Kx Lx = 0.8 x 20 = 16 ft. = 192 in. Effective length for minor (y) axis buckling = Ky Ly = 1.0 x 20 = 20 ft. = 240 in.
Step III. Determine the relevant section properties
For W12 x 50: elastic modulus = E = 29000 ksi (constant for all steels) For W12 x 50: Ix = 391 in4. Iy = 56.3 in4 (see page 1-21 of the AISC manual)
Step IV. Calculate the buckling strength
Critical load for buckling about x - axis = Pcr-x =
(K x
2 E I x
L x )2
2 29000 391
(192)2
Pcr-x = 3035.8 kips Critical load for buckling about y-axis = Pcr-y =
(K y L y )2
2 E I y
2 29000 56.3
(240)2
Pcr-y = 279.8 kips Buckling strength of the column = smaller (Pcr-x, Pcr-y) = Pcr = 279.8 kips Minor (y) axis buckling governs.
Notes:
Minor axis buckling usually governs for all doubly symmetric cross-sections. However, for some cases, major (x) axis buckling can govern.
Note that the steel yield stress was irrelevant for calculating this buckling strength.
3.3 INELASTIC COLUMN BUCKLING
Let us consider the previous example. According to our calculations Pcr = 279.8 kips. This Pcr will cause a uniform stress f = Pcr/A in the cross-section
For W12 x 50, A = 14.6 in2. Therefore, for Pcr = 279.8 kips; f = 19.16 ksi The calculated value of f is within the elastic range for a 50 ksi yield stress material.
However, if the unsupported length was only 10 ft., Pcr = 1119 kips, and f = 76.6 kips.
(K y L y )2
2 E I y
would be calculated as
This value of f is ridiculous because the material will yield at 50 ksi and never develop f = 76.6 kips. The member would yield before buckling.
Equation (3.1) is valid only when the material everywhere in the cross-section is in the elastic region. If the material goes inelastic then Equation (3.1) becomes useless and cannot be used.
What happens in the inelastic range? Several other problems appear in the inelastic range. The member out-of-straightness has a significant influence on the buckling strength in the inelastic region. It must be accounted for.
The residual stresses in the member due to the fabrication process causes yielding in the cross-section much before the uniform stress f reaches the yield stress Fy.
The shape of the cross-section (W, C, etc.) also influences the buckling strength. In the inelastic range, the steel material can undergo strain hardening.
All of these are very advanced concepts and beyond the scope of CE405. You are welcome to CE805 to develop a better understanding of these issues. So, what should we do? We will directly look at the AISC Specifications for the strength of compression members, i.e., Chapter E (page 16.1-27 of the AISC manual).
3.4 AISC SPECIFICATIONS FOR COLUMN STRENGTH
The AISC specifications for column design are based on several years of research. These specifications account for the elastic and inelastic buckling of columns including all issues (member crookedness, residual stresses, accidental eccentricity etc.) mentioned above.
The specification presented here (AISC Spec E2) will work for all doubly symmetric crosssections and channel sections.
The design strength of columns for the flexural buckling limit state is equal to cPn Where,
c = 0.85
Pn = Ag Fcr
(Resistance factor for compression members) Fcr = 0.658 c Fy

2
For c 1.5 For c > 1.5

K L Fy r E
(3.2) (3.3)
(3.4)
0.877 Fcr = 2 Fy c
Where, c =
(3.5)
Ag = gross member area; L = unbraced length of the member;
K = effective length factor r = governing radius of gyration
1.0 Fcr/Fy 0.39
Fcr = 0.658 c
2
)F
0.877 Fcr = 2 Fy c
c =
K L Fy r E
1.5
Note that the original Euler buckling equation is Pcr =

Pcr 2E I 2E 2E = = r2 = 2 A g (K L )2 A g (K L )2 K L r F 1 1 2E = = 2 cr = 2 2 Fy K L c F Fy K L y r r E 1 Fcr = Fy 2 c Fcr =
2E I
(K L )2
Note that the AISC equation for c < 1.5 is Fcr = Fy -
0.877 2 c The 0.877 factor tries to account for initial crookedness.
For a given column section: Calculate I, Ag, r Determine effective length K L based on end boundary conditions. Calculate c If c is greater than 1.5, elastic buckling occurs and use Equation (3.4)
If c is less than or equal to 1.5, inelastic buckling occurs and use Equation (3.3)
Note that the column can develop its yield strength Fy as c approaches zero.
3.5 COLUMN STRENGTH
In order to simplify calculations, the AISC specification includes Tables. Table 3-36 on page 16.1-143 shows KL/r vs. cFcr for steels with Fy = 36 ksi. You can calculate KL/r for the column, then read the value of cFcr from this table The column strength will be equal to cFcr x Ag Table 3-50 on page 16.1-145 shows KL/r vs. cFcr for steels with Fy = 50 ksi.
In order to simplify calculations, the AISC specification includes more Tables. Table 4 on page 16.1-147 shows c vs. cFcr/Fy for all steels with any Fy. You can calculate c for the column, the read the value of cFcr/Fy The column strength will be equal to cFcr/Fy x (Ag x Fy)
EXAMPLE 3.2 Calculate the design strength of W14 x 74 with length of 20 ft. and pinned ends.
A36 steel is used. Solution Step I. Calculate the effective length and slenderness ratio for the problem Kx = Ky = 1.0 Lx = Ly = 240 in. Major axis slenderness ratio = KxLx/rx = 240/6.04 = 39.735 Minor axis slenderness ratio = KyLy/ry = 240/2.48 = 96.77 Step II. Calculate the buckling strength for governing slenderness ratio
The governing slenderness ratio is the larger of (KxLx/rx, KyLy/ry) KyLy/ry is larger and the governing slenderness ratio; c = Therefore, Fcr = 0.658 c Fy
2
K y Ly ry
Fy E
= 1.085
c < 1.5;
Therefore, Fcr = 21.99 ksi Design column strength = cPn = 0.85 (Ag Fcr) = 0.85 (21.8 in2 x 21.99 ksi) = 408 kips Design strength of column = 408 kips Check calculated values with Table 3-36. For KL/r = 97, cFcr = 18.7 ksi Check calculated values with Table 4. For c = 1.08, cFcr = 0.521
10
3.6 LOCAL BUCKLING LIMIT STATE
The AISC specifications for column strength assume that column buckling is the governing limit state. However, if the column section is made of thin (slender) plate elements, then failure can occur due to local buckling of the flanges or the webs.
Figure 4. Local buckling of columns
If local buckling of the individual plate elements occurs, then the column may not be able to develop its buckling strength.
Therefore, the local buckling limit state must be prevented from controlling the column strength.
Local buckling depends on the slenderness (width-to-thickness b/t ratio) of the plate element and the yield stress (Fy) of the material.
Each plate element must be stocky enough, i.e., have a b/t ratio that prevents local buckling from governing the column strength.
11
The AISC specification B5 provides the slenderness (b/t) limits that the individual plate elements must satisfy so that local buckling does not control.
The AISC specification provides two slenderness limits (p and r) for the local buckling of plate elements.
Fy
Compact
Axial Force, F
Non-Compact Slender F t Axial shortening, b
Figure 5. Local buckling behavior and classification of plate elements
If the slenderness ratio (b/t) of the plate element is greater than r then it is slender. It will locally buckle in the elastic range before reaching Fy
If the slenderness ratio (b/t) of the plate element is less than r but greater than p, then it is non-compact. It will locally buckle immediately after reaching Fy
If the slenderness ratio (b/t) of the plate element is less than p, then the element is
compact. It will locally buckle much after reaching Fy

If all the plate elements of a cross-section are compact, then the section is compact. If any one plate element is non-compact, then the cross-section is non-compact If any one plate element is slender, then the cross-section is slender.
The slenderness limits p and r for various plate elements with different boundary conditions are given in Table B5.1 on pages 16.1-14 and 16.1-15 of the AISC Spec. 12
Note that the slenderness limits (p and r) and the definition of plate slenderness (b/t) ratio depend upon the boundary conditions for the plate. If the plate is supported along two edges parallel to the direction of compression force, then it is a stiffened element. For example, the webs of W shapes If the plate is supported along only one edge parallel to the direction of the compression force, then it is an unstiffened element. Ex., the flanges of W shapes.
The local buckling limit state can be prevented from controlling the column strength by using sections that are non-compact If all the elements of the cross-section have calculated slenderness (b/t) ratio less than r, then the local buckling limit state will not control. For the definitions of b/t, p, r for various situations see Table B5.1 and Spec B5.
EXAMPLE 3.3 Determine the local buckling slenderness limits and evaluate the W14 x 74
section used in Example 3.2. Does local buckling limit the column strength? Solution Step I. Calculate the slenderness limits See Table B5.1 on page 16.1 14. For the flanges of I-shape sections in pure compression r = 0.56 x E = 0.56 x Fy
29000 = 15.9 36
For the webs of I-shapes section in pure compression r = 0.56 x E = 0.56 x Fy

29000 = 15.9 36
13
r = 1.49 x
E = 1.49 x Fy
29000 = 42.3 36
Step II. Calculate the slenderness ratios for the flanges and webs of W14 x 74 For the flanges of I-shape member, b = bf/2 = flange width / 2 Therefore, b/t = bf/2tf. For W 14 x 74, bf/2tf = 6.41 For the webs of I shaped member, b = h h is the clear distance between flanges less the fillet / corner radius of each flange For W14 x 74, h/tw = 25.4 (See Page 1-19 in AISC) (See pg. 16.1-12 of AISC) (See Page 1-19 in AISC)
Step III. Make the comparisons and comment For the flanges, b/t < r. Therefore, the flange is non-compact For the webs, h/tw < r. Therefore the web is non-compact Therefore, the section is compact Therefore, local buckling will not limit the column strength.
3.7 COLUMN DESIGN
The AISC manual has tables for column strength. See page 4-21 onwards. For wide flange sections, the column buckling strength (cPn) is tabulated with respect to the
effective length about the minor axis KyLy in Table 4-2.

The table takes the KyLy value for a section, and internally calculates the KyLy/ry, then c =
K y Ly ry Fy E
; and then the tabulated column strength using either Equation E2-2 or
E2-3 of the specification.
14
If you want to use the Table 4-2 for calculating the column strength for buckling about the
major axis, then do the following:

Take the major axis KxLx value. Calculate an equivalent (KL)eq =
K xLx rx / ry
Use the calculated (KL)eq value to find (cPn) the column strength for buckling about the
major axis from Table (4-2)
For example, consider a W14 x 74 column with KyLy = 20 ft. and KxLx = 25 ft. Material has yield stress = 50 ksi (always in Table 4-2). See Table 4-2, for KyLy = 20 ft., cPn = 467 kips (minor axis buckling strength) rx/ry for W14x74 = 2.44 from Table 4-2 (see page 4-23 of AISC). For KxLx = 25 ft., (KL)eq = 25/2.44 = 10.25 ft. For (KL)eq = 10.25 ft., cPn = 774 kips (major axis buckling strength) If calculated value of (KL)eq < KyLy then minor axis buckling will govern.
EXAMPLE 3.4 Determine the design strength of an ASTM A992 W14 x 132 that is part of a
braced frame. Assume that the physical length L = 30 ft., the ends are pinned and the column is braced at the ends only for the X-X axis and braced at the ends and mid-height for the Y-Y axis. Solution
Step I. Calculate the effective lengths. For W14 x 132: Kx = 1.0 and rx = 6.28 in; Ky = 1.0 Ly = 15 ft. ry = 3.76 in; Ag =38.8 in2
Lx = 30 ft. and
KxLx = 30 ft. and KyLy = 15 ft.
Step II. Determine the governing slenderness ratio

15
KxLx/rx = 30 x 12 in./6.28 in.= 57.32 KyLy/ry = 15 x 12 in./3.76 in. = 47.87 The larger slenderness ratio, therefore, buckling about the major axis will govern the column strength.
Step III. Calculate the column strength KxLx = 30 ft. From Table 4-2, Therefore, (KL)eq = for (KL)eq = 18.0 ft. K xLx 30 = 17.96 ft. = rx / ry 6.28 / 3.76
cPn = 1300 kips (design column strength)
Step IV. Check the local buckling limits For the flanges, bf/2tf = 7.15 For the web, h/tw = 17.7 <
<
r = 0.56 x r = 1.49 x
E = 13.5 Fy E = 35.9 Fy
Therefore, the section is non-compact. OK.
EXAMPLE 3.5 A compression member is subjected to service loads of 165 kips dead load and
535 kips of live load. The member is 26 ft. long and pinned at each end. Use A992 (50 ksi) steel and select a W shape Solution
Calculate the factored design load Pu Pu = 1.2 PD + 1.6 PL = 1.2 x 165 + 1.6 x 535 = 1054 kips
Select a W shape from the AISC manual Tables For KyLy = 26 ft. and required strength = 1054 kips Select W14 x 145 from page 4-22. It has cPn = 1160 kips
16
Select W12 x 170 from page 4-24. It has cPn = 1070 kips No no W10 will work. See Page 4-26 W14 x 145 is the lightest.
Note that column sections are usually W12 or W14. Usually sections bigger than W14 are usually not used as columns.
3.8 EFFECTIVE LENGTH OF COLUMNS IN FRAMES
So far, we have looked at the buckling strength of individual columns. These columns had various boundary conditions at the ends, but they were not connected to other members with moment (fix) connections.
The effective length factor K for the buckling of an individual column can be obtained for the appropriate end conditions from Table C-C2.1 of the AISC Manual .
However, when these individual columns are part of a frame, their ends are connected to other members (beams etc.). Their effective length factor K will depend on the restraint offered by the other members connected at the ends. Therefore, the effective length factor K will depend on the relative rigidity (stiffness) of the members connected at the ends.
The effective length factor for columns in frames must be calculated as follows:
First, you have to determine whether the column is part of a braced frame or an unbraced (moment resisting) frame. If the column is part of a braced frame then its effective length factor 0 < K 1 If the column is part of an unbraced frame then 1 < K
17
Then, you have to determine the relative rigidity factor G for both ends of the column G is defined as the ratio of the summation of the rigidity (EI/L) of all columns coming together at an end to the summation of the rigidity (EI/L) of all beams coming together at the same end.
E Ic Lc G= EI Lb b
- It must be calculated for both ends of the column.
Then, you can determine the effective length factor K for the column using the calculated value of G at both ends, i.e., GA and GB and the appropriate alignment chart
There are two alignment charts provided by the AISC manual, One is for columns in braced (sidesway inhibited) frames. See Figure C-C2.2a on page 16.1-191 of the AISC manual. 0 < K 1 The second is for columns in unbraced (sidesway uninhibited) frames. See Figure CC2.2b on page 16.1-192 of the AISC manual. 1 < K The procedure for calculating G is the same for both cases.
18
EXAMPLE 3.6 Calculate the effective length factor for the W12 x 53 column AB of the frame
shown below. Assume that the column is oriented in such a way that major axis bending occurs in the plane of the frame. Assume that the columns are braced at each story level for out-of-plane buckling. Assume that the same column section is used for the stories above and below.
10 ft.
W14 x 68
10 ft.
W14 x 68
A
12 ft.
W14 x 68
B
W12 x 79 W12 x 79
W12 x 79
18 ft. 20 ft.
15 ft.
18 ft.
Step I. Identify the frame type and calculate Lx, Ly, Kx, and Ky if possible.
It is an unbraced (sidesway uninhibited) frame. Lx = Ly = 12 ft. Ky = 1.0 Kx depends on boundary conditions, which involve restraints due to beams and columns connected to the ends of column AB.
Need to calculate Kx using alignment charts.
Step II - Calculate Kx
Ixx of W 12 x 53 = 425 in4
Ixx of W14x68 = 753
19
Ic 425 425 + L c 10 12 12 12 6.493 = = = 1.021 GA = Ib 723 723 6.360 + L b 18 12 20 12 Ic 425 425 + L c 12 12 15 12 5.3125 = = = 0.835 GB = Ib 723 723 6.360 + L b 18 12 20 12
Using GA and GB: Kx = 1.3
- from Alignment Chart on Page 3-6
Step III Design strength of the column
KyLy = 1.0 x 12 = 12 ft. Kx Lx = 1.3 x 12 = 15.6 ft. rx / ry for W12x53 = 2.11 (KL)eq = 15.6 / 2.11 = 7.4 ft.
KyLy > (KL)eq Therefore, y-axis buckling governs. Therefore cPn = 518 kips
3.8.1 Inelastic Stiffness Reduction Factor Modification
This concept for calculating the effective length of columns in frames was widely accepted for many years.
Over the past few years, a lot of modifications have been proposed to this method due to its several assumptions and limitation. Most of these modifications have not yet been accepted in to the AISC provisions.
One of the accepted modifications is the inelastic stiffness reduction factor. As presented earlier, G is a measure of the relative flexural rigidity of the columns (EIc/Lc) with respect to the beams (EIb/Lb) 20
However, if column buckling were to occur in the inelastic range (c < 1.5), then the flexural rigidity of the column will be reduced because Ic will be the moment of inertia of only the elastic core of the entire cross-section. See figure below
rc = 10 ksi rt = 5 ksi Yielded zone
rt = 5 ksi
Elastic core, Ic
rc = 10 ksi rt = 5 ksi
(a) Initial state residual stress
(b) Partially y ielded state at buckling
The beams will have greater flexural rigidity when compared with the reduced rigidity (EIc) of the inelastic columns. As a result, the beams will be able to restrain the columns better, which is good for column design.
This effect is incorporated in to the AISC column design method through the use of Table 4-1 given on page 4-20 of the AISC manual.
Table 4-1 gives the stiffness reduction factor () as a function of the yield stress Fy and the stress Pu/Ag in the column, where Pu is factored design load (analysis)
21
EXAMPLE 3.7 Calculate the effective length factor for a W10 x 60 column AB made from 50
ksi steel in the unbraced frame shown below. Column AB has a design factor load Pu = 450 kips. The columns are oriented such that major axis bending occurs in the plane of the frame. The columns are braced continuously along the length for out-of-plane buckling. Assume that the same column section is used for the story above
W14 x 74
12 ft.
W14 x 74
A
W12 x 79 W12 x 79
W12 x 79
20 ft.
15 ft.
18 ft.
18 ft.
Solution
Step I. Identify the frame type and calculate Lx, Ly, Kx, and Ky if possible.
It is an unbraced (sidesway uninhibited) frame. Ly = 0 ft. Ky has no meaning because out-of-plane buckling is not possible. Kx depends on boundary conditions, which involve restraints due to beams and columns connected to the ends of column AB.
Need to calculate Kx using alignment charts.
Step II (a) - Calculate Kx
Ixx of W 14 x 74 = 796 in4
Ixx of W 10 x 60 = 341 in4
22
Ic 341 341 + L c 12 12 15 12 4.2625 = = = 0.609 GA = Ib 796 796 7.002 + L b 18 12 20 12
G B = 10
- for pin support, see note on Page 16.1-191
Using GA and GB: Kx = 1.8
- from Alignment Chart on Page 16.1-192
Note, Kx is greater than 1.0 because it is an unbraced frame.
Step II (b) - Calculate Kx inelastic using stiffness reduction factor method
Reduction in the flexural rigidity of the column due to residual stress effects First calculate, Pu / Ag = 450 / 17.6 = 25.57 ksi Then go to Table 4-1 on page 4-20 of the manual, and read the value of stiffness reduction factor for Fy = 50 ksi and Pu/Ag = 25.57 ksi. Stiffness reduction factor = = 0.833
GA-inelastic = x GA = 0.833 x 0.609 = 0.507 GB = 10

- for pin support, see note on Page 16.1-191
Using GA-inelastic and GB, Kx-inelastic = 1.75
- alignment chart on Page 16.1-192
Note: You can combine Steps II (a) and (b) to calculate the Kx-inelastic directly. You dont need to calculate elastic Kx first. It was done here for demonstration purposes.
Note that Kx-inelastic< Kx. This is in agreement with the fact that the beams offer better resistance to the inelastic column AB because it has reduced flexural rigidity.
Step III Design strength of the column
KxLx = 1.75 x 15 = 26.25 ft. rx / ry for W10x60 = 1.71 (KL)eq = 26.25/1.71 = 15.35 ft. 23 - from Table 4-2, see page 4-26
cPn for X-axis buckling = 513.9 kips

Section slightly over-designed for Pu = 450 kips.
- from Table 4-2, see page 4-26
Column design strength = cPn = 513.9 kips

EXAMPLE 3.8:
Design Column AB of the frame shown below for a design load of 500 kips. Assume that the column is oriented in such a way that major axis bending occurs in the plane of the frame. Assume that the columns are braced at each story level for out-of-plane buckling. Assume that the same column section is used for the stories above and below.
10 ft.
W14 x 68
10 ft.
W14 x 68
A
12 ft.
W14 x 68
B
W12 x 79 W12 x 79
W12 x 79
18 ft. 20 ft.
15 ft.
18 ft.
Step I - Determine the design load and assume the steel material.
Design Load = Pu = 500 kips Steel yield stress = 50 ksi (A992 material)
Step II. Identify the frame type and calculate Lx, Ly, Kx, and Ky if possible.
It is an unbraced (sidesway uninhibited) frame.
24
Lx = Ly = 12 ft. Ky = 1.0 Kx depends on boundary conditions, which involve restraints due to beams and columns connected to the ends of column AB. Need to calculate Kx using alignment charts. Need to select a section to calculate Kx
Step III - Select a column section
Assume minor axis buckling governs.

Ky Ly = 12 ft. See Column Tables in AISC-LRFD manual Select section W12x53
cPn for y-axis buckling = 518 kips
Step IV - Calculate Kx-inelastic
Ixx of W 12 x 53 =425 in4 Pu/Ag = 500 / 15.6 = 32.05 ksi Stiffness reduction factor = = 0.58
I Ic Lc
b
Ixx of W14x68 = 753 in4
Account for the reduced flexural rigidity of the column due to residual stress effects
GA =
Lb
I
425 425 0.58 + 10 12 12 12 = 3.766 = 0.592 = 723 723 6.360 + 18 12 20 12 425 425 + 0.58 12 12 15 12 = 3.0812 = 0.484 = 723 723 6.360 + 18 12 20 12
GB =
Ic Lc
b
Lb
Using GA and GB: Kx-inelastic = 1.2
- from Alignment Chart
Step V - Check the selected section for X-axis buckling
Kx Lx = 1.2 x 12 = 14.4 ft. rx / ry for W12x53 = 2.11 25
Calculate (KL)eq to determine strength (cPn) for X-axis buckling (KL)eq = 14.4 / 2.11 = 6.825 ft. From the column design tables, cPn for X-axis buckling = 612.3 kips
Step VI. Check the local buckling limits
For the flanges, bf/2tf = 8.69 For the web, h/tw = 28.1
<
<
r = 0.56 x r = 1.49 x
E = 13.5 Fy E = 35.9 Fy
Therefore, the section is non-compact. OK, local buckling is not a problem

Step VII - Summarize the solution
Lx = Ly = 12 ft.
Ky = 1.0
Kx = 1.2 (inelastic buckling - sway frame-alignment chart method)
cPn for Y-axis buckling = 518 kips cPn for X-axis buckling = 612.3 kips
Y-axis buckling governs the design. Selected Section is W12 x 53 made from 50 ksi steel.
26
EXAMPLE 3.9
Design Column AB of the frame shown below for a design load of 450 kips. Assume that the column is oriented in such a way that major axis bending occurs in the plane of the frame. Assume that the columns are braced continuously along the length for out-of-plane buckling. Assume that the same column section is used for the story above.
W14 x 74
12 ft.
W14 x 74
A
W12 x 79 W12 x 79
W12 x 79
20 ft.
15 ft.
18 ft.
18 ft.
Step I - Determine the design load and assume the steel material.
Design Load = Pu = 450 kips Steel yield stress = 50 ksi
Step II. Identify the frame type and calculate Lx, Ly, Kx, and Ky if possible.
It is an unbraced (sidesway uninhibited) frame. Ly = 0 ft. Ky has no meaning because out-of-plane buckling is not possible. Kx depends on boundary conditions, which involve restraints due to beams and columns connected to the ends of column AB. Need to calculate Kx using alignment charts. Need to select a section to calculate Kx
27
Step III. Select a section
There is no help from the minor axis to select a section Need to assume Kx to select a section. See Figure below:
W14 x 74
12 ft. W14 x 74
A
W12 x 79 W12 x 79 W12 x 79
15 ft.
B
18 ft. 20 ft.
18 ft.
Kx = 2.0 Best Case Scenario
The best case scenario for Kx is when the beams connected at joint A have infinite flexural stiffness (rigid). In that case Kx = 2.0 from Table C-C2.1 Actually, the beams don't have infinite flexural stiffness. Therefore, calculated Kx should be greater than 2.0. To select a section, assume Kx = 2.0 KxLx = 2.0 x 15.0 ft. = 30.0 ft. Need to be able to calculate (KL)eq to be able to use the column design tables to select a section. Therefore, need to assume a value of rx/ry to select a section. See the W10 column tables on page 4-26. Assume rx/ry = 1.71, which is valid for W10 x 49 to W10 x 68. Obviously from the Tables, for (KL)eq = 17.5 ft., W10 x 60 is the first section that will have cPn > 450 kips
(KL)eq = 30.0/1.71 = 17.54 ft. -
Select W10x60 with cPn = 457.7 kips for (KL)eq = 17.5 ft.
28
Step IV - Calculate Kx-inelastic using selected section
Ixx of W 14 x 74 = 796 in4 Pu/Ag = 450 / 17.6 = 25.57 ksi Stiffness reduction factor = = 0.833
I Ic Lc
b
Ixx of W 10 x 60 = 341 in4
Account for the reduced flexural rigidity of the column due to residual stress effects
GA =
Lb
341 341 0.833 + 12 12 15 12 = 3.550 = 0.507 = 796 796 7.002 + 18 12 20 12
G B = 10
- for pin support
Using GA and GB: Kx-inelastic = 1.75 be equal to 10 instead of
- from Alignment Chart on Page 3-6
Calculate value of Kx-inelastic is less than 2.0 (the assumed value) because GB was assumed to
Step V - Check the selected section for X-axis buckling
Kx Lx = 1.75 x 15 = 26.25 ft. rx / ry for W10x60 = 1.71 (KL)eq = 26.25/1.71 = 15.35 ft. (cPn) for X-axis buckling = 513.9 kips
Section slightly over-designed for Pu = 450 kips.
W10 x 54 will probably be adequate, Student should check by calculating Kx inelastic and
cPn for that section.

Step VI. Check the local buckling limits
For the flanges, bf/2tf = 7.41 For the web, h/tw = 18.7
<
<
r = 0.56 x r = 1.49 x
E = 13.5 Fy E = 35.9 Fy
Therefore, the section is non-compact. OK, local buckling is not a problem
29
Step VII - Summarize the solution
Ly = 0 ft.
Ky = no buckling
Kx = 1.75 (inelastic buckling - sway frame - alignment chart method)
cPn for X-axis buckling = 513.9 kips

X-axis buckling governs the design. Selected section is W10 x 60 (W10 x 54 will probably be adequate).
30
3.9 DESIGN OF SINGLY SYMMETRIC CROSS-SECTIONS
So far, we have been talking about doubly symmetric wide-flange (I-shaped) sections and channel sections. These rolled shapes always fail by flexural buckling.
Singly symmetric (Tees and double angle) sections fail either by flexural buckling about the axis of non-symmetry or by flexural-torsional buckling about the axis of symmetry and the longitudinal axis.
Figure 6(a). Flexural buckling

y x
Figure 6(b). Flexural-torsional buckling
Flexural buckling will occur about the x-axis

Flexural-torsional buckling will occur about the y and z-axis
Smaller of the two will govern the design strength
Figure 6(c). Singly symmetric cross-section
The AISC specification for flexural-torsional buckling is given by Spec. E3. Design strength = cPn = 0.85 Ag Fcrft
Fcry + Fcrz Where, Fcrft = 2H 4 Fcry Fcrz H 1 1 (Fcry + Fcrz ) 2
(1)
(2) (3)
Fcry = critical stress for buckling about the y-axis, see Spec. E2.
31
Fcrz =
GJ A ro 2 Ix + Iy A
(4)
2 ro2 = polar radius of gyration about shear center (in.) = y o + 2 yo
(5) (6) (7)
H=1-
ro2
yo = distance between shear center and centroid (in.)
The section properties for calculating the flexural-torsional buckling strength Fcrft are given as follows: G=
E 2 (1 + )
J, ro2 , H are given for WT shapes in Table 1-32 on page 1-101 to page 1-105
ro2 , H are given for double-angle shapes in Table 1-35 on page 1-108 to 1-110
J for single-angle shape in Table 1-31 on page 1-98 to 1-100. (J2L = 2 x JL)
The design tables for WT shapes given in Table 4-5 on page 4-35 to 4-47. These design tables include the axial compressive strength for flexural buckling about the x axis and flexural-torsional buckling about the y and z axis.
32
EXAMPLE 3.10 Calculate the design compressive strength of a WT10.5 x 66. The effective
length with respect to x-axis is 25ft. 6in. The effective length with respect to the y-axis is 20 ft. and the effective length with respect to z-axis is 20ft. A992 steel is used. Solution
Step I. Buckling strength about x-axis
c-x =
K x Lx rx
Fy E
306 50 = 1.321 3.06 3.1416 29000

2
cPn = 0.85 x (0.658)1.321 x 50 x 19.4 = 397.2 kips

Values for Ag and rx from page 4-41 of the manual. Compare with tabulated design strength for buckling about x-axis in Table 4-5
Step II. Flexural-torsional buckling about the y and z axes
Calculate Fcry and Fcrz then calculate Fcrft and cPn

c-y =
K y Ly Fy ry E
2
240 50 = 1.083 2.93 3.1416 29000
Fcry = (0.658)1.083 x 50 = 30.6 ksi Fcrz = GJ/A ro2 = 11,153 x 5.62/(4.602 x 19.4) = 152.69
4 30.6 152.7 0.844 Fcrft = Fcry + Fcrz 1 1 4 Fcry Fcrz H = 30.6 + 152.7 1 1 2 H (30.6 + 152.7) 2 (Fcry + Fcrz ) 2 2 0.844
Fcrft =108.58 x 0.272 = 29.534 ksi -
cPn = 0.85 x Fcrft x Ag = 0.85 x 29.534 x 19.4 = 487 kips
33
Values for J, ro2 , and H were obtained from flexural-torsional properties given in Table 1-32 on page 1-102. Compare the cPn value with the value reported in Table 4-5 (page 4-41) of the AISC manual.
Step III. Design strength and check local buckling
Flanges: bf/2tf = 12.4/(2 x 1.03) = 6.02 , which is < r = 0.56 x
E = 13.5 Fy E = 18.08 Fy
Stem of Tee: d/tw = 10.9/0.65 = 16.77, which is < r = 0.75 x
Local buckling is not a problem. Design strength = 397.2 kips. X-axis flexural buckling governs.
3.10 DESIGN OF DOUBLE ANGLE SECTIONS
Double-angle sections are very popular as compression members in trusses and bracing members in frames. These sections consist of two angles placed back-to-back and connected together using bolts or welds. You have to make sure that the two single angle sections are connected such that they do not buckle (individually) between the connections along the length. The AISC specification E4.2 requires that Ka/rz of the individual single angles < of the
governing KL/r of the double angle.

where, a is the distance between connections and rz is the smallest radius of gyration of the single angle (see dimensions in Table 1-7)
Double-angle sections can fail by flexural buckling about the x-axis or flexural torsional buckling about the y and z axes.
34
For flexural buckling about the x-axis, the moment of inertia Ix-2L of the double angle will be equal to two times the moment of inertia Ix-L of each single angle.
For flexural torsional buckling, there is a slight problem. The double angle section will have some additional flexibility due to the intermittent connectors. This added flexibility will depend on the connection parameters.
According to AISC Specification E4.1, a modified (KL/r)m must be calculated for the double angle section for buckling about the y-axis to account for this added flexibility
KL a KL + = Intermediate connectors that are snug-tight bolted r r o rz m
2
Intermediate connectors that are welded or fully tensioned bolted:

2 KL KL + 0.82 = 1+ 2 r o r m
2
a ry
where, = separation ratio = h/2ry h = distance between component centroids in the y direction
35
3/8
EXAMPLE 3.11 Calculate the design strength of the compression
member shown in the figure. Two angles, 5 x 3 x are oriented with the
5 x 3 x
long legs back-to-back and separated by 3/8 in. The effective length KL is 16 ft. A36 steel is used. Assume three welded intermediate connectors
Solution Step I. Determine the relevant properties from the AISC manual Property Ag rx ry rz J
ro2
0.746 0.746
Single angle
Double angle
3.75 in2 1.58 in. 0.824 in. 0.642 in. 0.322 in4
7.5 in2 1.58 in. 1.24 in. ----0.644 in4 2.51 in. 0.646
1-75, 1-109
H AISC Page no. 1-36, 1-37, 1-99 Step II. Calculate the x-axis buckling strength
KL/rx = 16 x 12 /1.58 = 120.8

c-x =
K x Lx rx
Fy E
120.8 3.1416
2
36 = 1.355 29000
cPn = 0.85 x (0.658)1.355 x 36 x (2 x 3.75) = 106 kips
Step III. Calculate (KL/r)m for y-axis buckling
(KL/r) = 16 x 12/1.24 = 154.8
36
a/rz = 48/0.648 = 74.07 a/rz = 74.07 < 0.75 x KL/r = 0.75 x 154.8 = 115.2 (OK!)
= h/2ry = (2 x 0.75 + 0.375)/(2 x 0.829) = l.131 2 KL KL + 0.82 = 1+ 2 r o r m

2 (154.8)o + 0.82
a ry
1.1312 1 + 1.1312
48 0.829 =158.5
Step IV. Calculate flexural torsional buckling strength.
c-y =
Fy 1 KL =1.778 E r m
Fcry =
0.877 0.877 Fy = 36 = 9.987 ksi 2 c y 1.778 2
Fcrz=
GJ 11,200 0.644 = 151.4 ksi = Aro2 7.5 2.512
Fcrft = Fcry + Fcrz 1 1 4 Fcry Fcrz H = 9.987 + 151.4 1 1 4 9.987 151.4 0.646 2 2
2H (Fcry + Fcrz )
2 0.646
(9.987 + 151.4)
Fcrft = 9.748 ksi
cPn = 0.85 x Fcrft x Ag = 0.85 x 9.748 x 7.50 = 62.1 kips
Flexural torsional buckling strength controls. The design strength of the double angle member is 62.1 kips.
Step V. Compare with design strengths in Table 4-10 (page 4-84) of the AISC manual
cPn for x-axis buckling with unsupported length = 16 ft. = 106 kips cPn for y-z axis buckling with unsupported length = 16 ft. = 61.3 kips
37
These results make indicate excellent correlation between the calculations in steps II to IV and the tabulated values.
Design tables for double angle compression members are given in the AISC manual. See Tables 4-9, 4-10, and 4-11 on pages 4-78 to 4-93
In these Tables Fy = 36 ksi Back to back distance = 3/8 in. Design strength for buckling about x axis Design strength for flexural torsional buckling accounting for the modified slenderness ratio depending on the number of intermediate connectors.
These design Tables can be used to design compression members as double angle sections.
38
Tension Member Design
Chapter 4. TENSION MEMBER DESIGN
4.1 INTRODUCTORY CONCEPTS Stress: The stress in an axially loaded tension member is given by Equation (4.1)
f = P A
(4.1)
where, P is the magnitude of load, and A is the cross-sectional area normal to the load The stress in a tension member is uniform throughout the cross-section except: near the point of application of load, and at the cross-section with holes for bolts or other discontinuities, etc.
For example, consider an 8 x in. bar connected to a gusset plate and loaded in tension as shown below in Figure 4.1
Gusset plate
b
7/8 in. diameter hole
Section b-b
a
8 x in. bar
Section a-a
Figure 4.1 Example of tension member. Area of bar at section a a = 8 x = 4 in2 Area of bar at section b b = (8 2 x 7/8 ) x = 3.12 in2
Therefore, by definition (Equation 4.1) the reduced area of section b b will be subjected to higher stresses
However, the reduced area and therefore the higher stresses will be localized around section b b.
The unreduced area of the member is called its gross area = Ag The reduced area of the member is called its net area = An
4.2 STEEL STRESS-STRAIN BEHAVIOR The stress-strain behavior of steel is shown below in Figure 4.2
Fu Fy
Stress, f
Strain,
Figure 4.2 Stress-strain behavior of steel In Figure 4.2, E is the elastic modulus = 29000 ksi. Fy is the yield stress and Fu is the ultimate stress
y is the yield strain and u is the ultimate strain
Deformations are caused by the strain . Figure 4.2 indicates that the structural deflections will be small as long as the material is elastic (f < Fy)
Deformations due to the strain will be large after the steel reaches its yield stress Fy.
4.3 DESIGN STRENGTH A tension member can fail by reaching one of two limit states: (1) excessive deformation; or (2) fracture Excessive deformation can occur due to the yielding of the gross section (for example section a-a from Figure 4.1) along the length of the member Fracture of the net section can occur if the stress at the net section (for example section b-b in Figure 4.1) reaches the ultimate stress Fu. The objective of design is to prevent these failure before reaching the ultimate loads on the structure (Obvious). This is also the load and resistance factor design approach recommended by AISC for designing steel structures
4.3.1 Load and Resistance Factor Design The load and resistance factor design approach is recommended by AISC for designing steel structures. It can be understood as follows: Step I. Determine the ultimate loads acting on the structure The values of D, L, W, etc. given by ASCE 7-98 are nominal loads (not maximum or ultimate) During its design life, a structure can be subjected to some maximum or ultimate loads caused by combinations of D, L, or W loading. 3
The ultimate load on the structure can be calculated using factored load combinations, which are given by ASCE and AISC (see pages 2-10 and 2-11 of AISC manual). The most relevant of these load combinations are given below: 1.4 D 1.2 D + 1.6 L + 0.5 (Lr or S) 1.2 D + 1.6 (Lr or S) + (0.5 L or 0.8 W) 1.2 D + 1.6 W + 0.5 L + 0.5 (Lr or S) 0.9 D + 1.6 W (4.2 1) (4.2 2) (4.2 3) (4.2 4) (4.2 5)
Step II. Conduct linear elastic structural analysis Determine the design forces (Pu, Vu, and Mu) for each structural member
Step III. Design the members The failure (design) strength of the designed member must be greater than the corresponding design forces calculated in Step II. See Equation (4.3) below:
Rn >
-
i Qi
(4.3)
Where, Rn is the calculated failure strength of the member
is the resistance factor used to account for the reliability of the material behavior and
equations for Rn
Qi is the nominal load i is the load factor used to account for the variability in loading and to estimate the ultimate loading condition.
4.3.2 Design Strength of Tension Members Yielding of the gross section will occur when the stress f reaches Fy. f = P = Fy Ag
Therefore, nominal yield strength = Pn = Ag Fy Factored yield strength = t Pn where, t = 0.9 for tension yielding limit state See the AISC manual, section on specifications, Chapter D (page 16.1 24)
(4.4) (4.5)
Facture of the net section will occur after the stress on the net section area reaches the ultimate stress Fu
f = P = Fu Ae
Therefore, nominal fracture strength = Pn = Ae Fu Where, Ae is the effective net area, which may be equal to the net area or smaller. The topic of Ae will be addressed later. Factored fracture strength = t Ae Fu (4.6)
Where, t = 0.75 for tension fracture limit state (See page 16.1-24 of AISC manual)
4.3.3 Important notes Note 1. Why is fracture (& not yielding) the relevant limit state at the net section? Yielding will occur first in the net section. However, the deformations induced by yielding will be localized around the net section. These localized deformations will not cause excessive deformations in the complete tension member. Hence, yielding at the net section will not be a failure limit state. Note 2. Why is the resistance factor (t) smaller for fracture than for yielding? The smaller resistance factor for fracture (t = 0.75 as compared to t = 0.90 for yielding) reflects the more serious nature and consequences of reaching the fracture limit state. Note 3. What is the design strength of the tension member? 5
The design strength of the tension member will be the lesser value of the strength for the two limit states (gross section yielding and net section fracture). Note 4. Where are the Fy and Fu values for different steel materials? The yield and ultimate stress values for different steel materials are noted in Table 2 in the AISC manual on pages 16.1141 and 16.1142. Note 5. What are the most common steels for structural members? See Table 2-1 in the AISC manual on pages 224 and 2-25. According to this Table: the preferred material for W shapes is A992 (Fy = 50 ksi; Fu = 65 ksi); the preferred material for C, L , M and S shapes is A36 (Fy = 36 ksi; Fu = 58 ksi). All these shapes are also available in A572 Gr. 50 (Fy = 50 ksi; Fu = 65 ksi). Note 6. What is the amount of area to be deducted from the gross area to account for the presence of bolt-holes? The nominal diameter of the hole (dh) is equal to the bolt diameter (db) + 1/16 in. However, the bolt-hole fabrication process damages additional material around the hole diameter. Assume that the material damage extends 1/16 in. around the hole diameter. Therefore, for calculating the net section area, assume that the gross area is reduced by a hole diameter equal to the nominal hole-diameter + 1/16 in.
Example 3.1 A 5 x bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with six 7/8 in. diameter bolts as shown in below. Assume that the effective net area Ae equals the actual net area An and compute the tensile design strength of the member.
Gusset plate b b 7/8 in. diameter bolt
a 5 x in. bar A572 Gr. 50
Solution Gross section area = Ag = 5 x = 2.5 in2 Net section area (An) Bolt diameter = db = 7/8 in. Nominal hole diameter = dh = 7/8 + 1/16 in. = 15/16 in. Hole diameter for calculating net area = 15/16 + 1/16 in. = 1 in. Net section area = An = (5 2 x (1)) x = 1.5 in2
Gross yielding design strength = t Pn = t Fy Ag Gross yielding design strength = 0.9 x 50 ksi x 2.5 in2 = 112.5 kips
Fracture design strength = t Pn = t Fu Ae Assume Ae = An (only for this problem) Fracture design strength = 0.75 x 65 ksi x 1.5 in2 = 73.125 kips
Design strength of the member in tension = smaller of 73.125 kips and 112.5 kips
Therefore, design strength = 73.125 kips (net section fracture controls).
Example 3.2 A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The service loads are 35 kips dead load and 15 kips live load. Determine the adequacy of this member using AISC specification. Assume that the effective net area is 85% of the computed net area. (Calculating the effective net area will be taught in the next section). Gross area of angle = Ag = 2.86 in2 (from Table 1-7 on page 1-36 of AISC)
L 4 x 4 x 3/ 8 d b = 5/8 in.
a
Gusset plate
Section a-a
Net section area = An Bolt diameter = 5/8 in. Nominal hole diameter = 5/8 + 1/16 = 11/16 in. Hole diameter for calculating net area = 11/16 + 1/16 = 3/4 in. Net section area = Ag (3/4) x 3/8 = 2.86 3/4 x 3/8 = 2.579 in2
Effective net area = Ae = 0.85 x 2.579 in2 = 2.192 in2 Gross yielding design strength = t Ag Fy = 0.9 x 2.86 in2 x 36 ksi = 92.664 kips Net section fracture = t Ae Fu = 0.75 x 2.192 in2 x 58 ksi = 95.352 kips
Design strength = 92.664 kips
(gross yielding governs)
Ultimate (design) load acting for the tension member = Pu The ultimate (design) load can be calculated using factored load combinations given on page 2-11 of the AISC manual, or Equations (4.2-1 to 4.2-5) of notes (see pg. 4) According to these equations, two loading combinations are important for this problem. These are: (1) 1.4 D; and (2) 1.2 D + 1.6 L The corresponding ultimate (design) loads are: 1.4 x (PD) = 1.4 (35) = 49 kips 1.2 (PD) + 1.6 (PL) = 66 kips (controls)
The ultimate design load for the member is 66 kips, where the factored dead + live loading condition controls.
Compare the design strength with the ultimate design load The design strength of the member (92.664 kips) is greater than the ultimate design load (66 kips). -
t Pn (92.664 kips) > Pu (66 kips)
The L 4 x 4 x 3/8 in. made from A36 steel is adequate for carrying the factored loads.
4.4 EFFECTIVE NET AREA The connection has a significant influence on the performance of a tension member. A connection almost always weakens the member, and a measure of its influence is called joint efficiency. Joint efficiency is a function of: (a) material ductility; (b) fastener spacing; (c) stress concentration at holes; (d) fabrication procedure; and (e) shear lag.
All factors contribute to reducing the effectiveness but shear lag is the most important. Shear lag occurs when the tension force is not transferred simultaneously to all elements of the cross-section. This will occur when some elements of the cross-section are not connected.
For example, see Figure 4.3 below, where only one leg of an angle is bolted to the gusset plate.
Figure 4.3 Single angle with bolted connection to only one leg. A consequence of this partial connection is that the connected element becomes overloaded and the unconnected part is not fully stressed. Lengthening the connection region will reduce this effect Research indicates that shear lag can be accounted for by using a reduced or effective net area Ae Shear lag affects both bolted and welded connections. Therefore, the effective net area concept applied to both types of connections. For bolted connection, the effective net area is Ae = U An For welded connection, the effective net area is Ae = U Ag
Where, the reduction factor U is given by: U = 1x 0.9 L
(4.7)
10
Where, x is the distance from the centroid of the connected area to the plane of the connection, and L is the length of the connection. If the member has two symmetrically located planes of connection, x is measured from the centroid of the nearest one half of the area. Additional approaches for calculating x for different connection types are shown in the AISC manual on page 16.1-178.
The distance L is defined as the length of the connection in the direction of load. For bolted connections, L is measured from the center of the bolt at one end to the center of the bolt at the other end. For welded connections, it is measured from one end of the connection to other. If there are weld segments of different length in the direction of load, L is the length of the longest segment. Example pictures for calculating L are given on page 16.1-179 of AISC.
The AISC manual also gives values of U that can be used instead of calculating x /L. They are based on average values of x /L for various bolted connections. For W, M, and S shapes with width-to-depth ratio of at least 2/3 and for Tee shapes cut from them, if the connection is through the flanges with at least three fasteners per line in the direction of applied load ...U = 0.90 For all other shapes with at least three fasteners per line ... U = 0.85 For all members with only two fasteners per line U = 0.75 For better idea, see Figure 3.8 on page 41 of the Segui text-book. These values are acceptable but not the best estimate of U If used in the exam or homeworks, full points for calculating U will not be given
11
Example 3.3 Determine the effective net area and the corresponding design strength for the single angle tension member of Example 3.2. The tension member is an L 4 x 4 x 3/8 in. made from A36 steel. It is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The spacing between the bolts is 3 in. center-to-center. Compare your results with those obtained for Example 3.2.
x
L 4 x 4 x 3/ 8 d b = 5/8 in.
a
Gusset plate
L 4 x 4 x 3/ 8
Gross area of angle = Ag = 2.86 in2 Net section area = An Bolt diameter = 5/8 in.
(from Table 1-7 on page 1-36 of AISC)
Hole diameter for calculating net area = 11/16 + 1/16 = 3/4 in. Net section area = Ag (3/4) x 3/8 = 2.86 3/4 x 3/8 = 2.579 in2
x is the distance from the centroid of the area connected to the plane of connection For this case x is equal to the distance of centroid of the angle from the edge. This value is given in the Table 1-7 on page 1-36 of the AISC manual. x = 1.13 in.
L is the length of the connection, which for this case will be equal to 2 x 3.0 in.
12
L = 6.0 in.
x 1.13 = 1= 0.8116 in. L 6.0
U = 1-
Effective net area = Ae = 0.8116 x 2.579 in2 = 2.093 in2 Gross yielding design strength = t Ag Fy = 0.9 x 2.86 in2 x 36 ksi = 92.664 kips Net section fracture = t Ae Fu = 0.75 x 2.093 in2 x 58 ksi = 91.045 kips Design strength = 91.045 kips In Example 3.2 Factored load = Pu = 66.0 kips Design strength = t Pn = 92.66 kips (gross section yielding governs) Net section fracture strength = t Pn = 95.352 kips (assuming Ae = 0.85) (net section fracture governs)
Comparing Examples 3.2 and 3.3 Calculated value of U (0.8166) is less than the assumed value (0.85) The assumed value was unconservative. It is preferred that the U value be specifically calculated for the section. After including the calculated value of U, net section fracture governs the design strength, but the member is still adequate from a design standpoint.
13
Example 3.4 Determine the design strength of an ASTM A992 W8 x 24 with four lines if in. diameter bolts in standard holes, two per flange, as shown in the Figure below. Assume the holes are located at the member end and the connection length is 9.0 in. Also calculate at what length this tension member would cease to satisfy the slenderness limitation in LRFD specification B7
in. diameter bolts
W 8 x 24
3 in.
3 in.
3 in.
Holes in beam flange
Solution: For ASTM A992 material: Fy = 50 ksi; and Fu = 65 ksi For the W8 x 24 section: Ag = 7.08 in2 tw = 0.285 in. tf = 0.4 in. d = 7.93 in. bf = 6.5 in. ry = 1.61 in.
Gross yielding design strength = t Pn = t Ag Fy = 0.90 x 7.08 in2 x 50 ksi = 319 kips Net section fracture strength = t Pn = t Ae Fu = 0.75 x Ae x 65 ksi Ae = U An - for bolted connection
An = Ag (no. of holes) x (diameter of hole) x (thickness of flange) An = 7.08 4 x (diameter of bolt + 1/8 in.) x 0.4 in. An = 5.68 in2
14
U =1-
x 0.90 L
What is x for this situation? x is the distance from the edge of the flange to the centroid of the half (T) section
(b f t f ) tf 2 +( d 2tf 2 tw ) ( d + 2t f 4 )
x=
bf t f +
d tw 2
6.5 0.4 0.2 + 3.565 0.285 2.1825 = 0.76 6.5 0.4 + 3.565 0.285
x can be obtained from the dimension tables for Tee section WT 4 x 12. See page 1-50 and 1-51 of the AISC manual: x = 0.695 in.
The calculated value is not accurate due to the deviations in the geometry U = 1x 0.695 = 1= 0.923 L 9 .0
But, U 0.90. Therefore, assume U = 0.90
Net section fracture strength = t Ae Fu = 0.75 x 0.9 x 5.68 x 65 = 249.2 kips The design strength of the member is controlled by net section fracture = 249.2 kips According to LRFD specification B7, the maximum unsupported length of the member is limited to 300 ry = 300 x 1.61 in. = 543 in. = 40.3 ft.
15
4.4.1 Special cases for welded connections If some elements of the cross-section are not connected, then Ae will be less than An For a rectangular bar or plate Ae will be equal to An However, if the connection is by longitudinal welds at the ends as shown in the figure below, then Ae = UAg Where, U = 1.0 for L w U = 0.87 for 1.5 w L < 2 w U = 0.75 for w L < 1.5 w L = length of the pair of welds w w = distance between the welds or width of plate/bar
AISC Specification B3 gives another special case for welded connections. For any member connected by transverse welds alone, Ae = area of the connected element of the cross-section
16
Example 3.5 Consider the welded single angle L 6x 6 x tension member made from A36 steel shown below. Calculate the tension design strength.
Solution Ag = 5.00 in2 An = 5.00 in2 Ae = U An - because it is a welded connection - where, U = 1 x L
x = 1.68 in. for this welded connection L = 6.0 in. for this welded connection U = 11.168 = 0.72 6.0
Gross yielding design strength = t Fy Ag = 0.9 x 36 x 5.00 = 162 kips Net section fracture strength = t Fu Ae = 0.75 x 58 x 0.72 x 5.00 = 156.6 kips Design strength = 156.6 kips (net section fracture governs)
17
4.5 STAGGERED BOLTS For a bolted tension member, the connecting bolts can be staggered for several reasons: (1) To get more capacity by increasing the effective net area (2) To achieve a smaller connection length (3) To fit the geometry of the tension connection itself. For a tension member with staggered bolt holes (see example figure above), the relationship f = P/A does not apply and the stresses are a combination of tensile and shearing stresses on the inclined portion b-c.
18
Net section fracture can occur along any zig-zag or straight line. For example, fracture can occur along the inclined path a-b-c-d in the figure above. However, all possibilities must be examined.
Empirical methods have been developed to calculate the net section fracture strength According to AISC Specification B2 net width = gross width - d +
s2 4g
where, d is the diameter of hole to be deducted (dh + 1/16, or db + 1/8) s2/4g is added for each gage space in the chain being considered s is the longitudinal spacing (pitch) of the bolt holes in the direction of loading g is the transverse spacing (gage) of the bolt holes perpendicular to loading dir. net area (An) = net width x plate thickness effective net area (Ae) = U An where U = 1- x /L (t = 0.75)
net fracture design strength = t Ae Fu
19
EXAMPLE 3.6 Compute the smallest net area for the plate shown below: The holes are for 1 in. diameter bolts.
i 3 in. 5 in. c 5 in. 3 in. f h d e j a b
3 in. 3 in. 3 in. 3 in. 3 in. 3 in.
The effective hole diameter is 1 + 1/8 = 1.125 in. For line a-b-d-e wn = 16.0 2 (1.125) = 13.75 in.
For line a-b-c-d-e wn = 16.0 3 (1.125) + 2 x 32/ (4 x 5) = 13.52 in.
The line a-b-c-d-e governs: An = t wn = 0.75 (13.52) = 10.14 in2
Note Each fastener resists an equal share of the load Therefore different potential failure lines may be subjected to different loads. For example, line a-b-c-d-e must resist the full load, whereas i-j-f-h will be subjected to 8/11 of the applied load. The reason is that 3/11 of the load is transferred from the member before i-j-f-h received any load.
20
Staggered bolts in angles. If staggered lines of bolts are present in both legs of an angle, then the net area is found by first unfolding the angle to obtain an equivalent plate. This plate is then analyzed like shown above. The unfolding is done at the middle surface to obtain a plate with gross width equal to the sum of the leg lengths minus the angle thickness. AISC Specification B2 says that any gage line crossing the heel of the angle should be reduced by an amount equal to the angle thickness. See Figure below. For this situation, the distance g will be = 3 + 2 in.
21
22
4.6 BLOCK SHEAR For some connection configurations, the tension member can fail due to tear-out of material at the connected end. This is called block shear. For example, the single angle tension member connected as shown in the Figure below is susceptible to the phenomenon of block shear.
(a)
(b)
Shear failure (c) Tension failure
Figure 4.4 Block shear failure of single angle tension member For the case shown above, shear failure will occur along the longitudinal section a-b and tension failure will occur along the transverse section b-c AISC Specification (SPEC) Chapter D on tension members does not cover block shear failure explicitly. But, it directs the engineer to the Specification Section J4.3
23
Block shear strength is determined as the sum of the shear strength on a failure path and the tensile strength on a perpendicular segment. Block shear strength = net section fracture strength on shear path + gross yielding strength on the tension path OR Block shear strength = gross yielding strength of the shear path + net section fracture strength of the tension path
Which of the two calculations above governs? See page 16.1 67 (Section J4.3) of the AISC manual When Fu Ant 0.6Fu Anv; t Rn = (0.6 Fy Agv + Fu Ant) (0.6 FuAnv + Fu Ant) When Fu Ant < 0.6Fu Anv; t Rn = (0.6 Fu Anv + Fy Agt) (0.6 FuAnv + Fu Ant) Where, = 0.75 Agv = gross area subject to shear Agt = gross area subject to tension Anv = net area subject to shear Ant = net area subject to tension
24
EXAMPLE 3.8 Calculate the block shear strength of the single angle tension member considered in Examples 3.2 and 3.3. The single angle L 4 x 4 x 3/8 made from A36 steel is connected to the gusset plate with 5/8 in. diameter bolts as shown below. The bolt spacing is 3 in. center-to-center and the edge distances are 1.5 in and 2.0 in as shown in the Figure below. Compare your results with those obtained in Example 3.2 and 3.3
x
L 4 x 4 x 3/ 8
2 .0
.0 3 .0 1 .5 3
d b = 5/8 in.
a
L 4 x 4 x 3/ 8
Gusset plate
Step I. Assume a block shear path and calculate the required areas
2 .0
.0 3 .0 1 .5 3
d b = 5/8 in.
Gusset plate
Agt = gross tension area = 2.0 x 3/8 = 0.75 in2 Ant = net tension area = 0.75 0.5 x (5/8 + 1/8) x 3/8 = 0.609 in2 Agv = gross shear area = (3.0 + 3.0 +1.5) x 3/8 = 2.813 in2 Anv = net tension area = 2.813 2.5 x (5/8 + 1/8) x 3/8 = 2.109 in2
25
Step II. Calculate which equation governs 0.6 Fu Anv = 0.6 x 58 x 2.109 = 73.393 kips Fu Ant = 58 x 0.609 = 35.322 kips 0.6 Fu Anv > Fu Ant Therefore, equation with fracture of shear path governs
Step III. Calculate block shear strength -
t Rn = 0.75 (0.6 Fu Anv + Fy Agt)

t Rn = 0.75 (73.393 + 36 x 0.75) = 75.294 kips
Compare with results from previous examples Example 3.2: Ultimate factored load = Pu = 66 kips Gross yielding design strength = t Pn = 92.664 kips Assume Ae = 0.85 An Net section fracture strength = 95.352 kips Design strength = 92.664 kips (gross yielding governs) Example 3.3 Calculate Ae = 0.8166 An Net section fracture strength = 91.045 kips Design strength = 91.045 kips (net section fracture governs) Member is still adequate to carry the factored load (Pu) = 66 kips Example 3.8 Block shear fracture strength = 75.294 kips Design strength = 75.294 kips (block shear fracture governs) Member is still adequate to carry the factored load (Pu) = 66 kips
26
Bottom line: Any of the three limit states (gross yielding, net section fracture, or block shear failure) can govern. The design strength for all three limit states has to be calculated. The member design strength will be the smallest of the three calculated values The member design strength must be greater than the ultimate factored design load in tension.
Practice Example Determine the design tension strength for a single channel C15 x 50 connected to a 0.5 in. thick gusset plate as shown in Figure. Assume that the holes are for 3/4 in. diameter bolts and that the plate is made from structural steel with yield stress (Fy) equal to 50 ksi and ultimate stress (Fu) equal to 65 ksi.
gusset plate
3 @ 3 = 9
center-to-center
C15 x 50
1.5
Limit state of yielding due to tension: Tn = 0.9 * 50 *14.7 = 662kips Limit state of fracture due to tension: 7 An = Ag nd e t = 14.7 4 (0.716 ) = 12.19in 2 8 x 0.798 2 Ae = UAn = 1 An = 1 * 12.19 = 10.57in 6 L Check: U = 0.867 0.9 OK.
27
Note: The connection eccentricity, x, for a C15X50 can be found on page 1-51 (LRFD).
Tn = 0.75 * 65 *10.57 = 515kips

Limit state of block shear rupture: 7 0.6 Fu Anv = 0.6 * 65 * 2 * 7.5 2.5 * * 0.716 = 296.6925 8 7 Fu Ant = 65 * 9 3 * 0.716 = 296.6925 8 Fu Ant 0.6 Fu Anv
296.6925 Rn = 0.6 Fy Agv + Fu Ant = 0.750.6 * 50 * 15 * 0.716 + 65 * = 464kips 65
Block shear rupture is the critical limit state and the design tension strength is 464kips.
28
4.7 Design of tension members The design of a tension member involves finding the lightest steel section (angle, wideflange, or channel section) with design strength (Pn) greater than or equal to the maximum factored design tension load (Pu) acting on it. -
Pn Pu
Pu is determined by structural analysis for factored load combinations
Pn is the design strength based on the gross section yielding, net section fracture, and
block shear rupture limit states.
For gross yielding limit state, Pn = 0.9 x Ag x Fy Therefore, 0.9 x Ag x Fy Pu Pu Therefore, Ag 0.9 Fy For net section fracture limit state, Pn = 0.75 x Ae x Fu Therefore, 0.75 x Ae x Fu Pu Pu Therefore, Ae 0.75 Fu But, Ae = U An Where, U and An depend on the end connection.
Thus, designing the tension member goes hand-in-hand with designing the end connection, which we have not covered so far.
Therefore, for this chapter of the course, the end connection details will be given in the examples and problems.
The AISC manual tabulates the tension design strength of standard steel sections Include: wide flange shapes, angles, tee sections, and double angle sections.
29
The gross yielding design strength and the net section fracture strength of each section is tabulated.
This provides a great starting point for selecting a section.
There is one serious limitation The net section fracture strength is tabulated for an assumed value of U = 0.75, obviously because the precise connection details are not known For all W, Tee, angle and double-angle sections, Ae is assumed to be = 0.75 Ag The engineer can first select the tension member based on the tabulated gross yielding and net section fracture strengths, and then check the net section fracture strength and the block shear strength using the actual connection details.
Additionally for each shape the manual tells the value of Ae below which net section fracture will control: Thus, for W shapes net section fracture will control if Ae < 0.923 Ag For single angles, net section fracture will control if Ae < 0.745 Ag For Tee shapes, net section fracture will control if Ae < 0.923 For double angle shapes, net section fracture will control if Ae < 0.745 Ag
Slenderness limits Tension member slenderness l/r must preferably be limited to 300 as per LRFD specification B7
30
Example 3.10 Design a member to carry a factored maximum tension load of 100 kips. (a) Assume that the member is a wide flange connected through the flanges using eight in. diameter bolts in two rows of four each as shown in the figure below. The center-to-center distance of the bolts in the direction of loading is 4 in. The edge distances are 1.5 in. and 2.0 in. as shown in the figure below. Steel material is A992
in. d iameter bolts 2 in. 1.5 in. 4 in.
1.5 in. 2 in. 4 in. Holes in beam flange
SOLUTION Step I. Select a section from the Tables Go to the TEN section of the AISC manual. See Table 3-1 on pages 3-17 to 3-19. From this table, select W8x10 with Ag = 2.96 in2, Ae = 2.22 in2. Gross yielding strength = 133 kips, and net section fracture strength=108 kips This is the lightest section in the table. Assumed U = 0.75. And, net section fracture will govern if Ae < 0.923 Ag
Step II. Calculate the net section fracture strength for the actual connection According to the Figure above, An = Ag - 4 (db + 1/8) x tf An = 2.96 - 4 (3/4 + 1/8) x 0.205 = 2.24 in2 The connection is only through the flanges. Therefore, the shear lag factor U will be the distance from the top of the flange to the centroid of a WT 4 x 5. 31
See DIM section of the AISC manual. See Table 1-8, on pages 1-50, 1-51 x = 0.953 U = 1- x /L = 1 - 0.953 / 4 = 0.76 Ae = 0.76 An = 0.76 x 2.24 = 1.70 in2
tPn = 0.75 x Fu x Ae = 0.75 x 65 x 1.70 = 82.9 kips

Unacceptable because Pu = 100 kips; REDESIGN required
Step III. Redesign Many ways to redesign. One way is shown here: Assume t Pn > 100 kips Therefore, 0.75 x 65 x Ae > 100 kips Therefore, Ae > 2.051 in2 Assume, Ae = 0.76 An Therefore An > 2.7 in2 But, Ag = An + 4 (db + 1/8) x tf Therefore Ag > 2.7 + 3.5 x tf - Go to the section dimension table 1-1 on page 1-22 of the AISC manual. Select next highest section. For W 8 x 13, tf = 0.255 in. Therefore, Ag > 2.7 + 3.5 x 0.255 = 3.59 in2 From Table 1-1, W8 x 13 has Ag = 3.84 in2 > 3.59 in2 Therefore, W8 x 13 is acceptable and is chosen. (based on previous calculations, step II) (based on previous calculations, step II)
32
Step IV. Check selected section for net section fracture Ag = 3.84 in2 An = 3.84 - 3.5 x 0.255 = 2.95 in2 From dimensions of WT4 x 6.5, x = 1.03 in. Therefore, U = 1- x /L = 1-1.03/4 = 0.74 Therefore, Ae = U An = 0.74 x 2.95 = 2.19 in2 Therefore, net section fracture strength = 0.75 x 65 x 2.19 = 106.7 kips Which is greater than 100 kips (design load). Therefore, W 8 x 13 is acceptable.
Step V. Check the block shear rupture strength o Identify the block shear path
2 in.
4 in.
1.5 in.
1.5 in.
2 in.
4 in.
The block shear path is show above. Four blocks will separate from the tension member (two from each flange) as shown in the figure above.
Agv = [(4+2) x tf ] x 4
= 6 x 0.255 x 4 = 6.12 in2
- for four tabs
Anv = {4+2 - 1.5 x (db+1/8)} x tf x 4 = 4.78 in2 Agt = 1.5 x tf x 4 = 1.53 in2 Ant = {1.5 - 0.5 x (db+1/8)}x tf x 4 = 1.084 in2
Identify the governing equation:
33
FuAnt = 65 x 1.084 = 70.4 kips 0.6FuAnv = 0.6 x 65 x 4.78 = 186.42 kips , which is > FuAnt
Calculate block shear strength -
tRn = 0.75 (0.6FuAnv + FyAgt) = 0.75 (186.42 + 50 x 1.53) = 197.2 kips

Which is greater than Pu = 100 kips. Therefore W8 x 13 is still acceptable
Summary of solution Design load Ag An U Ae Yield strength 3.84 2.95 0.74 2.19 173 kips Fracture strength 106.7 kips Block-shear strength 197.2 kips
Mem.
W8x13 100 kips
Design strength = 106.7 kips (net section fracture governs) W8 x 13 is adequate for Pu = 100 kips and the given connection
34
EXAMPLE 3.11 Design a member to carry a factored maximum tension load of 100 kips. (b) The member is a single angle section connected through one leg using four 1 in. diameter bolts. The center-to-center distance of the bolts is 3 in. The edge distances are 2 in. Steel material is A36
x
3.0 in.
2.0 in.
4.0 in.
2.0 in. 3.0 in.
3.0 in.
3.0 in.
Step I. Select a section from the Tables Go to the TEN section of the AISC manual. See Table 3-2 on pages 3-20 to 3-21. From this table, select L4x3x1/2 with Ag = 3.25 in2, Ae = 2.44 in2. Gross yielding strength = 105 kips, and net section fracture strength=106 kips This is the lightest section in the table. Assumed U = 0.75. And, net section fracture will govern if Ae < 0.745 Ag
Step II. Calculate the net section fracture strength for the actual connection According to the Figure above, An = Ag - 1 (db + 1/8) x t An = 3.25 - 1(1 + 1/8) x 0.5 = 2.6875 in2 The connection is only through the long leg. Therefore, the shear lag factor U will be the distance from the back of the long leg to the centroid of the angle. See DIM section of the AISC manual. See Table 1-7, on pages 1-36, 1-37 x = 0.822 in. U = 1- x /L = 1 - 0.822 /9 = 0.908 But U must be 0.90. Therefore, let U = 0.90 35
Ae = 0.90 An = 0.90 x 2.6875 = 2.41 in2
tPn = 0.75 x Fu x Ae = 0.75 x 58 x 2.41 = 104.8 kips

Acceptable because Pu = 100 kips.
Step V. Check the block shear rupture strength o Identify the block shear path
2.0 in.
2.0 in. 3.0 in.
3.0 in.
3.0 in.
Agv = (9+2) x 0.5 = 5.5 in2 Anv = [11 - 3.5 x (1+1/8)] x 0.5 = 3.53 in2 Agt = 2.0 x 0.5 = 1.0 in2 Ant = [2.0 - 0.5 x (1 + 1/8)] x 0.5 = 0.72 in2
Identify the governing equation: FuAnt = 58 x 0.72 = 41.76 kips 0.6FuAnv = 0.6 x 58 x 3.53 = 122.844 in2, which is > FuAnt
Calculate block shear strength -
tRn = 0.75 (0.6FuAnv + FyAgt) = 0.75 (122.84 + 36 x 1.0) = 119.133 kips

Which is greater than Pu = 100 kips. Therefore L4x3x1/2 is still acceptable
36
Summary of solution Yield Fracture Block-shear strength strength strength 3.25 2.69 0.9 2.41 105 kips 104.8 kips 119.13 kips Design strength = 104.8 kips (net section fracture governs) L4x3x1/2 is adequate for Pu = 100 kips and the given connection Ag An U Ae
Mem.
Design load L4x3x1/2 100 kips
Note: For this problem Ae/Ag = 2.41/3.25 = 0.741, which is < 0.745. As predicted by the AISC manual, when Ae /Ag < 0.745, net section fracture governs.
37
CHAPTER 5. BOLTED CONNECTION
5.1 INTRODUCTORY CONCEPTS There are different types of bolted connections. They can be categorized based on the type of loading. Tension member connection and splice. It subjects the bolts to forces that tend to shear the shank. Beam end simple connection. It subjects the bolts to forces that tend to shear the shank. Hanger connection. The hanger connection puts the bolts in tension
The bolts are subjected to shear or tension loading. In most bolted connection, the bolts are subjected to shear. Bolts can fail in shear or in tension. You can calculate the shear strength or the tensile strength of a bolt
Simple connection: If the line of action of the force acting on the connection passes through the center of gravity of the connection, then each bolt can be assumed to resist an equal share of the load.
The strength of the simple connection will be equal to the sum of the strengths of the individual bolts in the connection.
We will first concentrate on bolted shear connections.
5.2 BOLTED SHEAR CONNECTIONS We want to design the bolted shear connections so that the factored design strength ( Rn) is greater than or equal to the factored load. So, we need to examine the various possible failure modes and calculate the corresponding design strengths. Possible failure modes are: Shear failure of the bolts Failure of member being connected due to fracture or block shear or . Edge tearing or fracture of the connected plate Tearing or fracture of the connected plate between two bolt holes Excessive bearing deformation at the bolt hole
Shear failure of bolts Average shearing stress in the bolt = fv = P/A = P/( db2/4) P is the load acting on an individual bolt A is the area of the bolt and db is its diameter Strength of the bolt = P = fv x ( db2/4) where fv = shear yield stress = 0.6Fy
Bolts can be in single shear or double shear as shown below. When the bolt is in double shear, two cross-sections are effective in resisting the load. The bolt in double shear will have the twice the shear strength of a bolt in single shear.
Failure of connected member We have covered this in detail in Ch. 2 on tension members Member can fail due to tension fracture or block shear.
Bearing failure of connected/connecting part due to bearing from bolt holes Hole is slightly larger than the fastener and the fastener is loosely placed in hole Contact between the fastener and the connected part over approximately half the circumference of the fastener As such the stress will be highest at the radial contact point (A). However, the average stress can be calculated as the applied force divided by the projected area of contact Average bearing stress fp = P/(db t), where P is the force applied to the fastener. The bearing stress state can be complicated by the presence of nearby bolt or edge. The bolt spacing and edge distance will have an effect on the bearing str. Bearing stress effects are independent of the bolt type because the bearing stress acts on the connected plate not the bolt.
A possible failure mode resulting from excessive bearing close to the edge of the connected element is shear tear-out as shown below. This type of shear tear-out can also occur between two holes in the direction of the bearing load. Rn = 2 x 0.6 Fu Lc t = 1.2 Fu Lc t
To prevent excessive deformation of the hole, an upper limit is placed on the bearing load. This upper limit is proportional to the fracture stress times the projected bearing area Rn = C x Fu x bearing area = C Fu db t If deformation is not a concern then C = 3, If deformation is a concern then C=2.4 C = 2.4 corresponds to a deformation of 0.25 in.
Finally, the equation for the bearing strength of a single bolts is Rn where, = 0.75 and Rn = 1.2 Lc t Fu < 2.4 db t Fu Lc is the clear distance in the load direction, from the edge of the bolt hole to the edge of the adjacent hole or to the edge of the material
This relationship can be simplified as follows: The upper limit will become effective when 1.2 Lc t Fu = 2.4 db t Fu i.e., the upper limit will become effective when Lc = 2 db If Lc < 2 db, If Lc > 2 db, Rn = 1.2 Lc t Fu Rn = 1.4 db t Fu
5.3 DESIGN PROVISIONS FOR BOLTED SHEAR CONNECTIONS In a simple connection, all bolts share the load equally.
T/n
T/n
T/n
T/n
T/n
T/n
In a bolted shear connection, the bolts are subjected to shear and the connecting / connected plates are subjected to bearing stresses.
T T
Bearing stresses in plate T Bolt in shear T Bearing stresses in plate
The shear strength of all bolts = shear strength of one bolt x number of bolts The bearing strength of the connecting / connected plates can be calculated using equations given by AISC specifications.
The tension strength of the connecting / connected plates can be calculated as discussed earlier in Chapter 2.
5.3.1 AISC Design Provisions Chapter J of the AISC Specifications focuses on connections. Section J3 focuses on bolts and threaded parts
AISC Specification J3.3 indicates that the minimum distance (s) between the centers of bolt holes is 2 d b . A distance of 3db is preferred.
2 3
AISC Specification J3.4 indicates that the minimum edge distance (Le) from the center of the bolt to the edge of the connected part is given in Table J3.4 on page 16.1-61. Table J3.4 specifies minimum edge distances for sheared edges, edges of rolled shapes, and gas cut edges.
AISC Specification J3.5 indicates that the maximum edge distance for bolt holes is 12 times the thickness of the connected part (but not more than 6 in.). The maximum spacing for bolt holes is 24 times the thickness of the thinner part (but not more than 12 in.).
Specification J3.6 indicates that the design tension or shear strength of bolts is FnAb Table J3.2 gives the values of and Fn Ab is the unthreaded area of bolt. In Table J3.2, there are different types of bolts A325 and A490. The shear strength of the bolts depends on whether threads are included or excluded from the shear planes. If threads are included in the shear planes then the strength is lower. We will always assume that threads are included in the shear plane, therefore less strength to be conservative.
We will look at specifications J3.7 J3.9 later. AISC Specification J3.10 indicates the bearing strength of plates at bolt holes. The design bearing strength at bolt holes is Rn Rn = 1.2 Lc t Fu 2.4 db t Fu - deformation at the bolt holes is a design consideration Where, Fu = specified tensile strength of the connected material 8
Lc = clear distance, in the direction of the force, between the edge of the hole and the edge of the adjacent hole or edge of the material (in.).
t = thickness of connected material
5.3.2 AISC Design Tables Table 7-10 on page 7-33 of the AISC Manual gives the design shear of one bolt. Different bolt types (A325, A490), thread condition (included or excluded), loading type (single shear or double shear), and bolt diameters (5/8 in. to 1-1/2 in.) are included in the Table. Table 7-11 on page 7-33 of the AISC Manual is an extension of Table 7-10 with the exception that it gives the shear strength of n bolts. Table 7-12 on page 7-34 of the AISC manual gives the design bearing strength at bolt holes for various bolt spacings. These design bearing strengths are in kips/in. thickness. The tabulated numbers must be multiplied by the plate thickness to calculate the design bearing strength of the plate. The design bearing strengths are given for different bolt spacings (2.67db and 3db), different Fu (58 and 65 ksi), and different bolt diameters (5/8 1-1/2 in.) Table 7-12 also includes the spacing (sfull) required to develop the full bearing strength for different Fu and bolt diameters Table 7-12 also includes the bearing strength when s > sfull Table 7-12 also includes the minimum spacing 2-2/3 db values
Table 7-13 in the AISC manual on page 7-35 is similar to Table 7-12. It gives the design bearing strength at bolt holes for various edge distances.
These design bearing strengths are in kips/in. thickness. The tabulated numbers must be multiplied by the plate thickness to calculate the design bearing strength of the plate.
The design bearing strengths are given for different edge distances (1.25 in. and 2 in.), different Fu (58 and 65 ksi), and different bolt diameters (5/8 1-1/2 in.)
Table 7-13 also includes the edge distance (Le full) required to develop the full bearing strength for different Fu and bolt diameters
Table 7-13 also includes the bearing strength when Le > Le full
10
Example 5.1 Calculate and check the design

A36
3/8 in.
5x
1.25 2.50 1.25
strength of the connection shown below. Is the connection adequate for carrying the factored load of 65 kips.
A36 65 k
in. bolts
1.25 2.50 1.25
Solution Step I. Shear strength of bolts The design shear strength of one bolt in shear = Fn Ab = 0.75 x 48 x x 0.752/4 Fn Ab = 15.9 kips per bolt (See Table J3.2 and Table 7-10) (See Table 7-11)
Shear strength of connection = 4 x 15.9 = 63.6 kips
Step II. Minimum edge distance and spacing requirements See Table J3.4, minimum edge distance = 1 in. for rolled edges of plates
The given edge distances (1.25 in.) > 1 in. Therefore, minimum edge distance requirements are satisfied.
Minimum spacing = 2.67 db = 2.67 x 0.75 = 2.0 in. Preferred spacing = 3.0 db = 3.0 x 0.75 = 2.25 in. The given spacing (2.5 in.) > 2.25 in. Therefore, spacing requirements are satisfied.
Step III. Bearing strength at bolt holes. Bearing strength at bolt holes in connected part (5 x in. plate) At edges, Lc = 1.25 hole diameter/2 = 1.25 (3/4 + 1/16)/2 = 0.844 in.
Rn = 0.75 x (1.2 Lc t Fu) = 0.75 x (1.2 x 0.844 x 0.5 x 58) = 22.02 kips
But, Rn 0.75 (2.4 db t Fu) = 0.75 x (2.4 x 0.75 x 0.5 x 58) = 39.15 kips Therefore, Rn = 22.02 kips at edge holes Compare with value in Table 7-13. Rn = 44.0 x 0.5 = 22.0 kips
11
At other holes, s = 2.5 in, Lc = 2.5 (3/4 +1/16) = 1.688 in. Rn = 0.75 x (1.2 Lc t Fu) = 0.75 x (1.2 x 1.688 x 0.5 x 58) = 44.05 kips But, Rn 0.75 (2.4 db t Fu) = 39.15 kips. Therefore Rn = 39.15 kips Therefore, Rn = 39.15 kips at other holes Compare with value in Table 7-12. Rn = 78.3 x 0.5 =39.15 kips
Therefore, bearing strength at holes = 2 x 22.02 + 2 x 39.15 = 122.34 kips
Bearing strength at bolt holes in gusset plate (3/8 in. plate) At edges, Lc = 1.25 hole diameter/2 = 1.25 (3/4 + 1/16)/2 = 0.844 in.
Rn = 0.75 x (1.2 Lc t Fu) = 0.75 x (1.2 x 0.844 x 0.375 x 58) = 16.52 k

But, Rn 0.75 (2.4 db t Fu) = 0.75 x (2.4 x 0.75 x 0.375 x 58) = 29.36 kips Therefore, Rn = 16.52 kips at edge holes Compare with value in Table 7-13. Rn = 44.0 x 3/8 = 16.5 kips
At other holes, s = 2.5 in, Lc = 2.5 (3/4 +1/16) = 1.688 in. Rn = 0.75 x (1.2 Lc t Fu) = 0.75 x (1.2 x 1.688 x 0.375 x 58) = 33.04 kips But, Rn 0.75 (2.4 db t Fu) = 29.36 kips Therefore, Rn = 29.36 kips at other holes Compare with value in Table 7-12. Rn = 78.3 x 0.375 = 29.36 kips
Therefore, bearing strength at holes = 2 x 16.52 + 2 x 29.36 = 91.76 kips
Bearing strength of the connection is the smaller of the bearing strengths = 91.76 kips
12
Connection Strength Shear strength = 63.3 kips Bearing strength (plate) = 122.34 kips Bearing strength (gusset) = 91.76 kips Connection strength (Rn) > applied factored loads (Q). Therefore ok.
13
Example 5.2 Design a double angle tension member and a gusset plated bolted connection system to carry a factored load of 100 kips. Assume A36 (36 ksi yield stress) material for the double angles and the gusset plate. Assume A325 bolts. Note that you have to design the double angle member sizes, the gusset plate thickness, the bolt diameter, numbers, and spacing. Solution Step I. Design and select a trial tension member See Table 3-7 on page 3-33 of the AISC manual. Select 2L 3 x 2 x 3/8 with Pn = 113 kips (yielding) and 114 kips (fracture) While selecting a trial tension member check the fracture strength with the load.
Step II. Select size and number of bolts The bolts are in double shear for this design (may not be so for other designs) See Table 7-11 on page 7-33 in the AISC manual Use four 3/4 in. A325 bolts in double shear
Rn = 127 kips
- shear strength of bolts from Table 7-11
Step III. Design edge distance and bolt spacing See Table J3.4 The minimum edge distance = 1 in. for 3/4 in. diameter bolts in rolled edges. Select edge distance = 1.25 in.
See specification J3.5 Minimum spacing = 2.67 db = 2.0 in. Preferred spacing = 3.0 db = 2.25 in. Select spacing = 3.0 in., which is greater than preferred or minimum spacing
14
Step IV. Check the bearing strength at bolt holes in angles Bearing strength at bolt holes in angles Angle thickness = 3/8 in. See Table 7-13 for the bearing strength per in. thickness at the edge holes Bearing strength at the edge holes (Le = 1.25 in.) = Rn = 44.0 x 3/8 = 16.5 k See Table 7-12 for the bearing strength per in. thickness at non-edge holes Bearing strength at non-edge holes (s = 3 in.) = Rn = 78.3 x 3/8 = 29.4 k Bearing strength at bolt holes in each angle = 16.5 + 3 x 29.4 = 104.7 kips Bearing strength of double angles = 2 x 104.7 kips = 209.4 kips
Step V. Check the fracture and block shear strength of the tension member This has been covered in the chapter on tension members and is left to the students.
Step VI. Design the gusset plate See specification J5.2 for designing gusset plates. These plates must be designed for the limit states of yielding and rupture Limit state of yielding o Rn = 0.9 Ag Fy > 100 kips o Therefore, Ag = L x t > 3.09 in2 o Assume t = in; Therefore L > 6.18 in. o Design gusset plate = 6.5 x in. o Yield strength = Rn = 0.9 x 6.5 x 0.5 x 36 = 105.3 kips
Limit state for fracture 15
o An = Ag (db+1/8) x t o An = 6.5 x 0.5 (3/4 + 1/8) x 0.5 = 2.81 in2 o But, An 0.85 Ag = 0.85 x 3.25 = 2.76 in2 o Rn = 0.75 x An x Fu = 0.75 x 2.76 x 58 = 120 kips Design gusset plate = 6.5 x 0.5 in.
Step VII. Bearing strength at bolt holes in gusset plates
Assume Le = 1.25 in. (same as double angles) Plate thickness = 3/8 in. Bearing strength at the edge holes = Rn = 44.0 x 1/2 = 22.0 k Bearing strength at non-edge holes = Rn = 78.3 x 1/2 = 39.15 k Bearing strength at bolt holes in gusset plate = 22.0 + 3 x 39.15 = 139.5 kips
Summary of Member and Connection Strength Connection Shear strength = 127 kips Bearing Strength = 139.5 (gusset) Member Gusset Plate Fracture = 120 kips
Yielding = 113 kips Yielding = 105.3 kips Block Shear = ?
Bearing strength = 209.4 kips (angles) Fracture = ?
Overall Strength is the smallest of all these numbers = 105.3 kips Gusset plate yielding controls Resistance > Factored Load (100 kips). Design is acceptable
16
5.4 SLIP-CRITICAL BOLTED CONNECTIONS High strength (A325 and A490) bolts can be installed with such a degree of tightness that they are subject to large tensile forces. These large tensile forces in the bolt clamp the connected plates together. The shear force applied to such a tightened connection will be resisted by friction as shown in the Figure below.
P P
Tightened
N =Tb N =Tb N =Tb
P F=N F=N
N =Tb
Tb
Tb
P
N = Tb
N = Tb
Thus, slip-critical bolted connections can be designed to resist the applied shear forces using friction. If the applied shear force is less than the friction that develops between the two surfaces, then no slip will occur between them.
However, slip will occur when the friction force is less than the applied shear force. After slip occurs, the connection will behave similar to the bearing-type bolted connections designed earlier.
17
Table J3.1 summarizes the minimum bolt tension that must be applied to develop a slipcritical connection.
The shear resistance of fully tensioned bolts to slip at factored loads is given by AISC Specification J3.8 a Shear resistance at factored load = Rn = 1.13 Tb Ns where, = 1.0 for standard holes
= 0.33 (Class A surface with unpainted clean mill scale surface: CE 405)
Tb = minimum bolt tension given in Table J3.1 Ns = number of slip planes See Table 7-15 on page 7-36 of the AISC manual. This Table gives the shear resistance of fully tensioned bolts to slip at factored loads on class A surfaces. For example, the shear resistance of 1-1/8 in. bolt fully tensioned to 56 kips (Table J3.1) is equal to 20.9 kips (Class A faying surface). When the applied shear force exceeds the Rn value stated above, slip will occur in the connection. The shear resistance of fully tensioned bolts to slip at service loads is given by AISC Specification J3.8 b. Shear resistance at service load = Rn = Fv Ab Where, = 1.0 for standard holes Fv = slip-critical resistance to shear at service loads, see Table A-J3.2 on page 16.1-116 of the AISC manual See Table 7-16 on page 7-37 of the AISC manual. This Table gives the shear resistance of fully tensioned bolts to slip at service loads on class A surfaces.
18
For example, the shear resistance of 1-1/8 in. bolt fully tensioned to 56 kips (Table J3.1) is equal to 16.9 kips (Class A faying surface).
When the applied shear force exceeds the Rn value stated above, slip will occur in the connection.
The final strength of the connection will depend on the shear strength of the bolts calculated using the values in Table 7-11 and on the bearing strength of the bolts calculated using the values in Table 7-12, 7-13. This is the same strength as that of a bearing type connection.
19
Example 5.3 Design a slip-critical splice for a tension member subjected to 300 kips of tension loading. The tension member is a W8 x 28 section made from A992 (50 ksi) material. The unfactored dead load is equal to 50 kips and the unfactored live load is equal to 150 kips. Use A325 bolts. The splice should be slip-critical at service loads. Solution Step I. Service and factored loads Service Load = D + L = 200 kips. Factored design load = 1.2 D + 1.6 L = 300 kips Tension member is W8 x 28 section made from A992 (50 ksi) steel. The tension splice must be slip critical (i.e., it must not slip) at service loads. Step II. Slip-critical splice connection Rn of one fully-tensioned slip-critical bolt = Fv Ab If db = 3/4 in. Rn of one bolt = 1.0 x 17 x x 0.752/4 = 7.51 kips Note, Fv = 17 ksi from Table A-J3.2 From Table 7-16 on page 7-37 Rn = 7.51 kips (See Spec. A-J3.8 b) page 16.1-117 of AISC
Rn of n bolts = 7.51 x n > 200 kips

Therefore, n > 26.63 If db = 7/8 in. Rn of one bolt = 10.2 kips Rn of n bolts = 10.2 x n > 200 kips Therefore, n > 19.6 bolts 20
(splice must be slip-critical at service)
-from Table 7-16 (splice must be slip-critical at service)
Example 5.3 Step I: Service and Factored Loads D := 50 Kips Service Loads Factored Loads L := 150 Kips Ps := D + L Pu := 1.2 D + 1.6 L Ps = 200 Pu = 300 Kips Kips
Step II: Slip Critical connection In Service loads consideration, Rn of one fully tenstioned slip-critical bolt = F v A b (As given in Spec. A-J3.8b - page 16.1-117) If diameter of the bolt = for one bolt d b := 3 4 in := 1.0 Ab := 4 Fv := 17 Ksi - A325 - Table A-J3.2
( db) 2
Rn = 7.51 Kips
Rn := Fv Ab n := Ps Rn 7 8 in Ab := 4
Number of bolts required
n = 26.63 (min. reqd.)
If diameter of the bolt = for one bolt
d b :=
( db) 2
Rn = 10.222Kips
Rn := Fv Ab n := Ps Rn
Number of bolts required
n = 19.565 (min. reqd.)
say we provide 24 bolts on either side of the center line, 6 on either side of the flanges, top + bottom Step III: Connection Details and spacings for 24 bolts on each W8 x 28 Note that there are 24 bolts on either side of the center line. In all there are 48 number - 7/8 in dia bolts used in the connection. Minimum pretension applied to the bolts = 39.0 Kips from Table J3.1 Minimum Edge distance from Table J3.4 = Le-min = 1.125 in Provide Edge Distance = Le := 1.25 in s := 2.67 d b s = 2.336 in
Minimum spacing (Spec. J3.3) =
Preferred spacing = s := 3 d b From table 7-12 sfull := 2.6875 in s := 3 in
s = 2.625
in
For design provide spacing =
Step IV: Connection Strength at factored loads The splice connection should be designed as a normal shear / bearing connection beyong this point for the factored load = 300 kips The shear strength of the bolts (Table 7-10) = 21.6 kips/bolt x 24 bolts = 518.4 Kips Bearing strength of 7/8 in. bolt at edge holes = Be := 45.7 Kip / in thickness Kip / in thickness Table 7-13 Table 7-12
Bearing strength of 7/8 in. bolt at other holes = Bo := 102 Total bearing strength of the bolt holes in wide flange section
Bt := 4 Be + 20 Bo Bt = 2.223 10
3
Kips
Step V: Design the splice plate
Fy := 50 Ksi
Fu := 65 Ksi
Pu = 300
Kips
Tension Yielding = 0.9 Ag F y > Pu
minAg := minAn :=
Pu 0.9 Fy Pu 0.75 Fu
minAg = 6.667 minAn = 6.154
in
Tension Fracture = 0.75 An F u > Pu
in
We know, flange width of W 8 x 28 = 6.54 in. This is the limiting width of the splice plate. The unknown quantity which is the thickness of each splice plate is calculated as shown. Net area = Gross area - area of the bolts An := Ag 4 7 1 8 An := minAn Here, Ag := 6.54 t An := 6.154
2
in
Solving for t, we get
tmin := 2.42 in
(This is the total thickness of the plate at the top and bottom)
Assume each plate of the dimensions
b := 6.54 in
tp := 1.25 in
therefore, total plate thickness = Check for An and A g: Ag := b t An := Ag 4 7 + 1 8 t

2
t := 2 tp
t = 2.5
in
>
tmin = 2.42 in
Ag = 16.35 in An = 6.35 <
>
minAg = 6.667 minAn = 6.154

2
in
in
>
in
Check
An = 6.35
in
0.85 Ag = 13.898 in
Strength of the splice plate in yielding = 0.9 Ag Fy = 735.75 fracture = Kips > 0.75 An Fu = 309.563 Kips Pu = 300 Kips
Check for bearing strength of the splice plates Check for block shear rupture
Step VI : Check member yield, fracture and block shear....
Example 4.4 Modify Example 4.2 so that the connection system is slip critical for the factored load of 100 kips. Solution Step I. Design and select a trial tension member (same as example 4.2) Select 2L 3 x 2 x 3/8 with Pn = 113 kips (yielding) and 114 kips (fracture)
Step II. Select size and number of bolts (modified step) The connection must be designed to be slip-critical at the factored loads -
Rn for one bolt = 1.0 x 1.13 x x Tb x Ns
(Tb from Table J3.1)
Rn for one 3/4 in. bolt = 1.0 x 1.13 x 0.33 x 28 x 2 = 20.9 kips
Rn for one 7/8 in. bolt = 1.0 x 1.13 x 0.33 x 39 x 2 = 29.1 kips See Values in Table 7-15.
Rn for and 7/8 in. bolts in double slip = 20.9 and 29.1 kips, respectively.
We need at least five in. bolts to have strength Rn = 5 x 20.9 = 104.5 k > 100 k We need at least four 7/8 in. bolts to have strength Rn = 4 x 29.1 = 116.4 k> 100
Use five in. fully tightened bolts. Bolts must be tightened to 28 kips. Compare with solution for example 4.2 where only four snug-tight in bolts design.
For the remaining steps III to VII follow Example 4.2 Step III. Design edge distance and bolt spacing Step IV. Check the bearing strength at bolt holes in angles Step V. Check the fracture and block shear strength of the tension member Step VI. Design the gusset plate Step VII. Bearing strength at bolt holes in gusset plates Summary of Member and Connection Strength 23
CHAPTER 6. WELDED CONNECTIONS
6.1 INTRODUCTORY CONCEPTS Structural welding is a process by which the parts that are to be connected are heated and fused, with supplementary molten metal at the joint. A relatively small depth of material will become molten, and upon cooling, the structural steel and weld metal will act as one continuous part where they are joined.
Fillet weld
Fillet weld
The additional metal is deposited from a special electrode, which is part of the electric circuit that includes the connected part. In the shielded metal arc welding (SMAW) process, current arcs across a gap between the electrode and the base metal, heating the connected parts and depositing part of the electrode into the molten base metal. A special coating on the electrode vaporizes and forms a protective gaseous shield, preventing the molten weld metal from oxidizing before it solidifies. The electrode is moved across the joint, and a weld bead is deposited, its size depending on the rate of travel of the electrode. As the weld cools, impurities rise to the surface, forming a coating called slag that must be removed before the member is painted or another pass is made with the electrode. Shielded metal arc welding is usually done manually and is the process universally used for field welds.
For shop welding, an automatic or semi automatic process is usually used. Foremost among these is the submerged arc welding (SAW),
In this process, the end of the electrode and the arc are submerged in a granular flux that melts and forms a gaseous shield. There is more penetration into the base metal than with shielded metal arc welding, and higher strength results.
Other commonly used processes for shop welding are gas shielded metal arc, flux cored arc, and electro-slag welding.
Quality control of welded connections is particularly difficult, because defects below the surface, or even minor flaws at the surface, will escape visual detection. Welders must be
properly certified, and for critical work, special inspection techniques such as radiography or ultrasonic testing must be used. The two most common types of welds are the fillet weld and the groove weld. Fillet weld examples: lap joint fillet welds placed in the corner formed by two plates Tee joint fillet welds placed at the intersection of two plates. Groove welds deposited in a gap or groove between two parts to be connected e.g., butt, tee, and corner joints with beveled (prepared) edges Partial penetration groove welds can be made from one or both sides with or without edge preparation.
6.2 Design of Welded Connections Fillet welds are most common and used in all structures. Weld sizes are specified in 1/16 in. increments A fillet weld can be loaded in any direction in shear, compression, or tension. However, it always fails in shear.
The shear failure of the fillet weld occurs along a plane through the throat of the weld, as shown in the Figure below.
L
a a
Throat = a = 0.707 a x cos45o
Failure Plane
Shear stress in fillet weld of length L subjected to load P = fv = If the ultimate shear strength of the weld = fw Rn = f w 0.707 a L w
P 0.707 a L w
Rn = 0.75 f w 0.707 a L w
i.e., factor = 0.75
fw = shear strength of the weld metal is a function of the electrode used in the SMAW process. The tensile strength of the weld electrode can be 60, 70, 80, 90, 100, 110, or 120 ksi. The corresponding electrodes are specified using the nomenclature E60XX, E70XX, E80XX, and so on. This is the standard terminology for weld electrodes. The strength of the electrode should match the strength of the base metal. If yield stress (y) of the base metal is 60 - 65 ksi, use E70XX electrode. If yield stress (y) of the base metal is 60 - 65 ksi, use E80XX electrode.
E70XX is the most popular electrode used for fillet welds made by the SMAW method. Table J2.5 in the AISC Specifications gives the weld design strength fw = 0.60 FEXX
For E70XX, fw = 0.75 x 0.60 x 70 = 31.5 ksi Additionally, the shear strength of the base metal must also be considered:
Rn = 0.9 x 0.6 Fy x area of base metal subjected to shear

where, Fy is the yield strength of the base metal. For example:
T
Elevation
Plan
Strength of weld in shear = 0.75 x 0.707 x a x Lw x fw
Strength of base metal = 0.9 x 0.6 x Fy x t x Lw
Smaller governs the strength of the weld Always check weld metal and base metal strength. Smaller value governs. In most cases, the weld metal strength will govern. In weld design problems it is advantageous to work with strength per unit length of the weld or base metal.
6.2.1 Limitations on weld dimensions (See AISC Spec. J2.2b on page 16.1-54 of manual) Minimum size (amin) - function of the thickness of the thickest connected plate - given in Table J2.4 of the AISC specifications Maximum size (amax)
- function of the thickness of the thinnest connected plate: - for plates with thickness 0.25 in., amax = 0.25 in. - for plates with thickness 0.25 in., amax = t - 1/16 in. Minimum length (Lw) - length (Lw) 4 a - Read J2.2 b - Intermittent fillet welds: Lw-min = 4 a and 1.5 in. Maximum effective length - read AISC J2.2b If weld length Lw < 100 a, then effective weld length (Lw-eff) = Lw If Lw < 300 a, then effective weld length (Lw-eff) = Lw (1.2 0.002 Lw/a) If Lw > 300 a, the effective weld length (Lw-eff) = 0.6 Lw otherwise, aeff = Lw / 4
Weld Terminations - read AISC J2.2b Lap joint fillet welds terminate at a distance > a from edge. Weld returns around corners must be > 2 a
Example 6.1. Determine the design strength of the tension member and connection system shown below. The tension member is a 4 in. x 3/8 in. thick rectangular bar. It is welded to a 1/2 in. thick gusset plate using E70XX electrode. Consider the yielding and fracture of the tension member. Consider the shear strength of the weld metal and the surrounding base metal.
t = 0.5 in.
a = 0.25 in.
4 in x 3/ 8 in.
5 in.
0.5 in.
0.5 in.
5 in.
Solution Step I. Check for the limitations on the weld geometry tmin = 3/8 in. (member) tmax = 0.5 in. (gusset) Therefore, amin = 3/16 in. amax = 3/8 - 1/16 = 5/16 in. Fillet weld size = a = 1/4 in. Lw-min = 1.0 in. - AISC Table J2.4 - AISC J2.2b - Therefore, OK! - OK.
Lw-min for each length of the weld = 4.0 in. (transverse distance between welds, see J2.2b) Given length = 5.0 in., which is > Lmin. Therefore, OK!
Length/weld size = 5/0.25 = 20 - Therefore, maximum effective length J2.2 b satisfied. End returns at the edge corner size - minimum = 2 a = 0.5 in. -Therefore, OK!
Step II. Design strength of the weld Weld strength = x 0.707 x a x 0.60 x FEXX x Lw = 0.75 x 0.707 x 0.25 x 0.60 x 70 x 10 = 55.67 kips Base Metal strength = x 0.6 x Fy x Lw x t = 0.9 x 0.6 x 50 x 10 x 3/8 = 101.25 kips Step III. Tension strength of the member
Rn = 0.9 x 50 x 4 x 3/8 = 67.5 kips Rn = 0.75 x Ae x 65

Ae = U A A = Ag = 4 x 3/8 = 1.5 in2 U = 0.75 , since connection length (Lconn) < 1.5 w Therefore, Rn = 54.8 kips
- tension yield - tension fracture
- See Spec. B3 - See Spec. B3
The design strength of the member-connection system = 54.8 kips. Tension fracture of the member governs. The end returns at the corners were not included in the calculations.
Example 6.2 Design a double angle tension member and connection system to carry a factored load of 250 kips. Solution Step I. Assume material properties Assume 36 ksi steel for designing the member and the gusset plates. Assume E70XX electrode for the fillet welds. Step II. Design the tension member From Table 3-7 on page 3-32 of the AISC manual, select 2L 5 x 3 x 1/2 made from 36 ksi steel with yield strength = 259 kips and fracture strength = 261 kips. Step III. Design the welded connection amin = 3/16 in. amax = 1/2 - 1/16 in. = 7/16 in. Design, a = 3/8 in. = 0.375 in. Shear strength of weld metal = Rn = 0.75 x 0.60 x FEXX x 0.707 x a x Lw = 8.35 Lw kips Strength of the base metal in shear = Rn = 0.9 x 0.6 x Fy x t x Lw = 9.72 Lw kips Shear strength of weld metal governs, Rn = 8.35 Lw kips Rn > 250 kips
8.35 Lw > 250 kips Lw > 29.94 in.
- Table J2.4 - J2.2b
Design, length of 1/2 in. E70XX fillet weld = 30.0 in. Shear strength of fillet weld = 250.5 kips
Step IV. Layout of Connection
(a)
Welding on both sides of gusset.
L1
(b)
2a L2
(c)
L3
Length of weld required = 30 in. Since there are two angles to be welded to the gusset plate, assume that total weld length for each angle will be 15.0 in. As shown in the Figure above, 15 in. of 1/2 in. E70XX fillet weld can be placed in three ways (a), (b), and (c). For option (a), the AISC Spec. J2.2b requires that the fillet weld terminate at a distance greater than the size (1/2 in.) of the weld. For this option, L1 will be equal to 7.5 in. For option (b), the AISC Spec. J2.2b requires that the fillet weld be returned continuously around the corner for a distance of at least 2 a (1 in.). For this option, L2 can be either 6.5 in. or 7.5 in. However, the value of 7.5 in. is preferred. For option (c), L3 will be equal to 5.75 in. 10
Step V. Fracture strength of the member Ae = U Ag
For the double angle section, use the value of x from Table 1-7 on page 1-37 of manual. Option (a) (b) (c)
x L 1-0.901/7.5 = 0.88 0.9
x
U = 1
1-0.901/6.5 =0.86 0.9 1-0.901/5.75 = 0.84 0.9
c.g.
Assume case (a). Therefore, U =0.88
Rn = 0.75 x 0.88 x 8.00 x 58 = 306.24 kips > 250 kips

Step VI. Design the gusset plate
- fracture limit state is ok!
Rn > Tu
Therefore, 0.9 x Ag x 36 > 250 kips Ag > 7.71 in2
- tension yielding limit state
Rn > Tu
Therefore, 0.75 x An x Fu > 250 kips An 0.85 Ag An > 5.747 in2 Design gusset plate thickness = 1.0 in. and width = 8.0 in.
- tension fracture limit state
- Spec. J5 Therefore, Ag > 6.76 in2

1/2 1/2 7.5 in. 7.5 in.
(a)
Gusset plate 8 x in.
Two 5 x 3.5 x 1/ 2 in
1/2 1/2
7.5 in. 7.5 in.
11
CE405 DESIGN PROJECT

Fall2003 Harichandran / Varma
1.0 OBJECTIVES 1. The CE405 design project requires each team to demonstrate a good knowledge of structural design. 2. Additionally, each team must demonstrate good report writing and presentation skills. 2.0 APPROACH It is anticipated that each team will work at least 3 hours per week on the project. The expected timeline for activities, goals achieved, and submissions for the project will be as follows: Week I II III IV V VI VII VIII IX X XI XII XIII XIII Dates 09/01 - 09/8 09/8 09/15 09/15 09/22 09/22 09/29 09/29 10/06 10/06 10/13 10/13 - 10/20 10/20 10/27 10/27 - 11/03 11/03 - 11/10 11/10 - 11/17 11/17 - 11/24 11/24 12/01 12/03 12/05 Activities and Goals Estimate dead, live, roof, snow loads on structure Estimate wind loads on structure Calculate loads on the frame to be designed Develop structural analysis model (assume) Conduct analysis and determine design forces Write and review preliminary report Design beams members Design columns and bracing members Design roof truss members Verify design forces using designed frame Design assigned roof truss connections Design assigned bracing connection Write and Review Final report Develop presentation Make presentation + celebrate! Final report Presentation Preliminary report Submission

3.0 PROJECT TEAMS The design project teams are as follows: Team Chief Engineer 1 2 3 4 Mengistu 5 Eunai Lee David Schroeder Jason Makowski Dan Kehoe Helen Ferede Mark Gipson Andrew Pauly Michelle Powell Luelseged Jill Beardslee Kevin Wheeler Todd Stelma Kie-Cung Liong Gregory Heim Project Manager Joshua Dudicz Brian Mcierney Michael Pluger A&D Engineer A&D Engineer A&D Engineer Clinton Loe Justin Wing Steven Siklich Derrick Dielman David Stolcenberg Dan Beauchamp Matthew Junak Lin Yu-Chen Dan Remondino
Bethany Enbright Mike Kenon
As such all team members are expected to contribute equally to the overall project. Please keep track of your individual contributions and those of other members in your group. At the end you will be required to grade your team members efforts and contributions. If possible, briefly indicate individual efforts and contributions in the preliminary and final project reports.

4.0 ROLE DEFINITIONS 4.1 Project Manager: The project manager is responsible for the planning, scheduling, coordination, and completion of the overall design project. The project manager will also run intelligence and interference for the group. The project manager will help the chief engineer (CE) and the analysis and design (A&D) engineers to complete the design project. The project manager will make the final presentation along with his team. The CE and the A&D engineers help the project manager to develop the group presentation.
4.2 Chief Engineer: The chief engineer is responsible for the overall accuracy of the completed work. The chief engineer will provide significant assistance to the A&D engineers to complete the project. The chief engineer will also double check the results The chief engineer will write the report with the help of the information and drawings provided by the A&D engineers. The chief engineer can communicate with the instructor about design issues. The chief engineer will assist the PM to develop the presentation.
4.3 Analysis and Design Engineers: The analysis and design engineers are responsible for working on the details of the project. They will work together and with the CE and the PM to complete the project accurately and in time. The A&D engineers are the backbone of the design firm. They should maintain a close working relationship with the CE. They will collaborate with the CE to develop the report and with the PM to develop the presentation.

5.0 DESIGN PROJECT Figure 1 shows the structural floor plan and layout of a new office building that will be built in Lansing. Figure 2 shows the structural elevation of the interior braced frame A-A. All frames in the north-south direction are similar to the braced frame shown in Figure 2. The structural elevation of the perimeter moment resisting frame B-B is shown in Figure 3. All frames in the east-west direction are similar to the moment frame shown in Figure 3. Design all the members of the interior frame A-A. Note that A-A is not an exterior frame. Design the frame according to the American Institute of Steel Construction (AISC) specifications. Design connections at joints P and C in frame A-A.
5.1 One Possible Approach Step I: Estimate the dead, live, roof, and snow loads Step II. Estimate the wind loads Step III. Calculate the resultant loads on the interior frame A-A Step IV. Assume sections for the members of frame A-A. Develop an analytical model of the structure Step VI: Perform the structural analysis with the assumed members to determine the design forces Step VII. Submit preliminary report. Step VII: Design the members for the design forces determined from Step VI Step VIII: Reanalyze the structure using the designed sections to verify the designs. Step IX: Design the connections. Step X: Write the final report. Step XI: Prepare a presentation for the project.

30 ft.
30 ft.
40 ft. Frame A-A
40 ft.
40 ft. Frame B -B
Pin/hinge connection Fix/moment connection
Figure 1. Structural floor plan and layout

R 10 ft. E 12 ft. D 12 ft. C 12 ft. B 15 ft. A F K H M I N S T J Q P O
30 ft.
30 ft.
Figure 2. Structural elevation of frame A -A

n m l
u t s
b1 a1 z
TO OT N
i
E ED B
ED GN SI
q
35 ft.
35 ft.
35 ft.
Figure 3. Structural elevation of frame B-B

6.0 PROJECT REPORTS The project reports should be brief readable document that summarize the relevant results from the analyses and design of the frame. They should include relevant drawings of the designed structure. The report should have enough information to assess the accuracy and the approach used for the design. Relevant AISC Specifications should be cited using their Specification numbers. The report should not be too verbose. Attach the analysis results as an appendix to the report. Very briefly summarize the contributions by the individual members of the team.
7.0 PROJECT PRESENTATION Each group will have eight minutes for the presentation and two minutes for questions and answers. Limit yourself to a total number of 12 - 15 slides. Prepare your presentation using Microsoft Powerpoint. Each group's presentation will be graded by all other groups and the instructor. Save some of your interesting questions for the day of the presentations. Please limit yourself to 12 - 15 slides for each presentation. Prepare your presentations using Microsoft Powerpoint.
9.0 GUIDELINES FOR THE FINAL PROJECT REPORT The final design project report must be a concise, organized, and easy-to-read document. The exact layout and table of contents of the final design project report is up to the individual teams. However, the report must at-least address the following issues: Preliminary Analysis - Model of the structural system - Summary of results from the elastic analysis of the preliminary structural model

- Emphasis on member design forces and corresponding governing load combination. - Displaced shapes of the frames for critical load combinations. Structural Design - Members - Summarize the results of the design process - Emphasis on selected material, member, strength (resistance), and controlling limit state. - Sample design calculations for some critical roof truss, columns, and bracing members. Structural Design - Connections - Summary of calculations for the design of connections for Joints S and G. - Engineering drawings of the designed connections. Final Analysis and Design Verification - Comparison of results from analysis of preliminary and designed structural system. - Emphasis on deviations in design member forces, and redesign of members (if any). Structural Weight, Fabrication Cost, and Design Cost - Determine the weight of each member and the total weight of steel in the structure. - Assuming a fabricated steel cost of $1.00 per pound, determine the total fabrication cost of the project. - Break the project, as your group has conducted it, into several tasks. Identify these tasks. - Develop a Table summarizing the number of hours dedicated by each group-member to each task. Identify total number of person-hours for each task and for the complete project. - Assuming a cost of $50.00 per person-hour, determine the cost of designing the project.

10.0 HANDOUT FOR CONNECTION DESIGN IN THE DESIGN PROJECT (needed only towards the end of the design)
This handout discusses the design of connections at joints S and G, shown in the figure below. It is similar but not identical to the connection design for the design project.
R 10 ft. E 12 ft. D 12 ft. C 12 ft. B 15 ft. A F K H M I N S T J P Q O
30 ft.
30 ft.
Figure 1. Structural elevation of Frame A-A
Working point: The working point for a connection is defined as the point of intersection of the centroidal axes of all members connected at the joint.
The working point (W.P) for all connections should correspond to the joints shown in the line sketches and assumed in the analysis & design.

Design the connections using either bolts or welds. Note that welds will be much easier. If you have assumed bolted connections during member design, then you will find that they will still be adequate for welded connections.
Example details of connection S and G are shown in the attached sheets. Additional references include the AISC manual pages 13-11 to 13-17 for truss connections and 13-3 to 13-11 for bracing member connections. See Example 13.2 (case b on page 13-35) for bracing connection examples. See Example 13.3 (page 13-38) for truss connection examples.
A sample gusset plate design is also shown. Additional reference for gusset plate design can be downloaded from: http://www.aisc.org/documents/dec_98.pdf
10

Example of Connection S - Bolted
Gusset S
Example of Connection S - Welded
Gusset
11

Example of Connection - G (Bolted and Welded options shown together)
Bracing member
Beam
Beam
Bracing member
12

Bracing connection design example (very brief, many steps omitted) Given: Bracing member, Lx = Ly = 34 ft. Kx = Ky =1.0 Pu = 90 kips (tension and compression). Design member Select double angle section 8 x 6 x 1/2 in. with long legs back-to-back, made from 50 ksi material See AISC manual page 4-82: Pn = 113 kips for x-axis buckling Pn = 92 kips for y-axis buckling y-axis buckling governs, need two connectors along the member length (student design). Design Connection of member to gusset plate If a bolted connection is desired, No. of bolts required = four 3/4 in. A325 bolts Rn = 127 kips. Design, edge distance (Le) = 1.5 in. and spacing (s) = 3.0 in. If welded connection is required, Let a = 5/16 in. (check with amin and amax) Design with E70XX electrode Rn = 0.75 x 0.6 x 70 x 0.707 x 5/16 x L = 6.96 L kips > 90 kips Therefore, L > 12.93 in. Design, L = 16 in. - (8 in. on either sides of the gusset plate)
13

5/16 5/16
4 4
5/16 5/16
4 4
Gusset Plate Design Gusset plate design is governed by the length of the critical section subjected to direct tension or compression. The length of the critical section can be estimate using the Whitmore gage-length method, shown in the Figure below. The Whitmore gage-length method assumes that the critical section is located at the last fastener long the line of force. The length (Lgw) of the critical section is estimated assuming 30o angles of spread from the length of the plate in direct tension or compression at the first fastener. The area of the critical section is equal to Lgw multiplied by the thickness (tg) of the gusset. The thickness (tg) of the gusset plate must be designed so that the gross yielding and net section fracture strength of the critical section are greater than factored tension force. Usually, the limit state of gusset plate buckling due to compression forces is also considered in the design process. However, this is beyond the scope of the current course.
14

Therefore, design the thickness (tg) of the gusset plate so that the gross yield strength in compression, with a factor of 0.85, is greater than the factored compressive force.
(a)
(b) Lgw =d b +2Ltan 30o 30o
(c) 30o Lgw =d+2Ltan30o
L Tu t Tn = 0.9 Fy Lgwtg > Tu t Tn = 0.75 Fu (Lgwn (db + 1/8)) tg > Tu Whitmore gage length and design of gusset plates: (a) member with bolts or welds; (b) Whitmore gage length for bolted conn.; (c ) Whitmore gage length for welded conn. t Tn = 0.9 Fy Lgwtg > Tu
Design Gusset Plate Lgw = 3/4 + 2 x 9 x tan30o = 11.14 in. tTn > Tu 0.9 x Lgw x tg x 50 > 90 Therefore, tg > 0.18 in. tTn > Tu 0.75 x (11.14 - 0.875) x tg x 65 > 90 Therefore, tg > 0.18 in. tTn > Pu 0.85 x (11.14) x tg x 50 > 90 Therefore, tg > 0.19 in. - gross yielding in compression (approx.) -net section fracture in tension - for bolted connection - gross yielding in tension - gross yielding in tension
15

Assume tg = either 3/8 in. or 1/2 in. or 3/4 in. for bolted connection gusset plate. All of these values are greater than that required. The final choice will be based on the designer. The instructor would prefer a 1/2 in. thick gusset plate. Lgw = 8 + 2 x 4 x tan 30o = 12.6 in. tTn > Tu 0.9 x 12.6 x tg x 50 > 90 Therefore, tg > 0.16 in. tTn > Tu 0.85 x 12.6 x tg x 50 > 90 Therefore, tg > 0.17 in. Design tg = 1/2 in. for the gusset plate. - gross yielding in compression. - gross yielding in tension
Design gusset plate to beam and column connection.

Tusin: design force for horizontal weld
Tucos: design force for vertical weld Tu
angle between the vertical and the line joining the corners of the gussets at the top and bottom levels
16

The weld joining the gusset to the beam must be designed for a design force of Tu x sin The weld joining the gusset to the column must be designed for a design force of Tu x cos These values come from page 11-22 of the AISC Volume II. Note that there are three other methods of designing these connections. However, the recommended method is the simplest. is the angle between the vertical and the line joining the corners of the gussets at the top and bottom level. Thus, is not exactly equal to the angle of the diagonal bracing member. In order to use the recommended simple design method for the connection, the bracing member centroidal axis should pass through the corners of the gusset plates as shown. Thus, the working point for the bracing member should be located at the corner of the gusset. This will cause some additional end moment in the beam due to the eccentricity of the working point with respect to its centroidal axis. This should have to be accounted for in the design process. However, it is beyond the scope of this course and design project.
17

Steel Members Design

Uploaded by

Copyright:

Available Formats

Steel Members Design

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Steel Members Design

Uploaded by

Copyright:

Available Formats

What are the primary responsibilities of the owner, architect, engineer, fabricator, and contractor?

What are the primary responsibilities of the owner, architect, engineer, fabricator, and contractor?

What are the parameters that can be varied in structural design?

What are the parameters that can be varied in structural design?

CE 405: Design of Steel Structures Prof. Dr. A.

1.0 INTRODUCTION TO STRUCTURAL ENGINEERING

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

35 ft. Pin/hinge connection Fix/moment connection

35 ft. Frame A -A Frame B-B

Figure 1. Structural floor plan and layout

Figure 2. Structural elevation of frame A-A

CE 405: Design of Steel Structures Prof. Dr. A. Varma

g 10 ft. f e 12 ft. d 12 ft. c 12 ft. b 15 ft. a

ELEVATION OF BRACED FRAME

ELEVATION OF MOMENT FRAME

PLAN OF ROOF TRUSS

ELEVATION OF BRACED FRAME

ELEVATION OF MOMENT FRAME

PLAN OF ROOF TRUSS

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

For practice, let us categorize the member shown in Figures 2 and 3.

Figure 2. Structural elevation of frame A-A

g 10 ft. f e 12 ft. d 12 ft. c 12 ft. b 15 ft. a

Figure 3. Structural elevation of frame B-B

CE 405: Design of Steel Structures Prof. Dr. A. Varma

Figure 4. Truss connection at S in Frame A-A.

CE 405: Design of Steel Structures Prof. Dr. A. Varma

Figure 5. Bracing connection and Simple Shear Connection at G in Frame A-A.

CE 405: Design of Steel Structures Prof. Dr. A. Varma

fillet welds shear tabs

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

=1 R2 = 1.2 - 0.05 F = 0.6

for F 4 for 4 < F < 12 for 12 F

where, F = no. of inches of rise per foot for pitched roof.

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

Where, Rn is the calculated failure strength of the member

CE 405: Design of Steel Structures Prof. Dr. A. Varma

Figure 8. Structural floor plan

Figure 9. Structural elevation in east-west direction

CE 405: Design of Steel Structures Prof. Dr. A. Varma

qz = 0.00256 Kz Kzt Kd V2I In Lansing V = 90 mph

CE 405: Design of Steel Structures Prof. Dr. A. Varma

Figure 11. External pressures on structural plan

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

CE 405: Design of Steel Structures Prof. Dr. A. Varma

4.0 4.0 4.0

Step II. Estimate uniformly distributed loads

CE 405: Design of Steel Structures Prof. Dr. A. Varma