REV G: 8/5/08

BM-V-SDB, BM-V-SD, BM-V-S, BM-V-SB

INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK
IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR
SERVICING THIS TOOL.

CARCASS SPLITTING SAW

TOOL DATA
MODEL: BANDMASTER BM-V-SDB
ASSEMBLY NO. 1730000
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 166 LB (75.5 KG)
MOTOR HORSEPOWER: 2HP / 3HP

MODEL: BANDMASTER BM-V-S

ASSEMBLY NO. 1708000
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 180 LB (82 KG)
MOTOR HORSEPOWER: 3HP / 5HP

MODEL: BANDMASTER BM-V-SD

ASSEMBY NO. 1708100
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 170 LB (77.3 KG)
MOTOR HORSEPOWER: 2HP / 3HP

MODEL: BANDMASTER BM-V-SB

ASSEMBLY NO. 1708050
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 200 LB (91 KG)
MOTOR HORSEPOWER: 3HP / 5HP

VIBRATION: LESS THAN (<) 123 dB < 1.41m/s2

NOISE:
LESS THAN 81dB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

1 OF 44

REV G: 8/5/08

! WARNING

= Hazards or unsafe practices which could result in severe personal injury,

death or substantial property damage.

! CAUTION

= Hazards or unsafe practices which could result in minor personal injury,

product or property damage.

! NOTICE

= Important installation, operation or maintenance information.

OPERATING AND SAFETY INSTRUCTIONS

! WARNING DO NOT OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTOOD THE SAFETY

INSTRUCTIONS AND OPERATING MANUALS.

! WARNING DO NOT OPERATE THIS TOOL UNTIL YOU HAVE RECEIVED TRAINING IN THE HANDLING,

OPERATION AND USE OF THIS TOOL.

STOP USING A MALFUNCTIONING OR DEFECTIVE TOOL IMMEDIATELY. REPORT ANY

! WARNING PROBLEMS OR DEFECTS TO YOUR SUPERVISOR FOR REMOVAL OF THE TOOL FROM

SERVICE.
! WARNING DO NOT ATTEMPT TO REPAIR THE TOOL YOURSELF.
! WARNING DO NOT ALLOW UNAUTHORIZED PERSONS TO USE TOOL.
! WARNING

REMOVE AND DISCONNECT POWER FROM THE TOOL WHEN TOOL IS LEFT UNATTENDED OR
IS NOT IN USE.
NEVER TIE DOWN, BYPASS, ALTER OR MODIFY THE ACTIVATING SWITCHES OR TRIGGERS OF

! WARNING THIS TOOL.

! WARNING NEVER MAKE ALTERATIONS OR MODIFICATIONS TO THIS TOOL.

BE CONSTANTLY AWARE AND ALERT FOR UNSAFE CONDITIONS AND REPORT THEM
! WARNING IMMEDIATELY TO YOUR SUPERVISOR.

! WARNING NEVER PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE CUTTING PATH OF THE

TOOL.
! WARNING NEVER ALLOW ANYONE ELSE TO PLACE THEIR HANDS OR ANY PART OF THEIR BODY IN THE

CUTTING PATH OF THE TOOL.

! WARNING
! WARNING

! CAUTION

DO NOT ACTIVATE CONTROL SWITCHES OR TRIGGERS OF THIS TOOL UNLESS YOU INTEND
TO TEST OR OPERATE THIS TOOL.
DO NOT USE THIS TOOL FOR ANY PURPOSE OTHER THAN ITS INTENDED PURPOSE.
WHEN OPERATING THIS TOOL WEAR THE PROTECTIVE GEAR AND SAFETY EQUIPMENT
SUPPLIED TO YOU.
THE NOISE EMISSION (SOUND PRESSURE LEVEL) AT THE WORKSTATION MAY EXCEED 80 dB

! WARNING (A). EAR AND SOUND PROTECTION GEAR IS REQUIRED.

VIBRATION: LESS THAN (<) 123 dB

NOISE: LESS THAN 81dB

< 1.41m/s2

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

2 OF 44

REV G: 8/5/08

! WARNING

OPERATING INSTRUCTIONS
ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.

1. TO ENSURE TOOL IS OPERATING PROPERLY, PERFORM FOLLOWING STEPS AT START OF EACH SHIFT:
MAKE SURE TOOL MOVES UP AND DOWN FREELY WHILE HANGING FROM BALANCER OVERHEAD.
WITH POWER TO TOOL TURNED ON, TEST TRIGGER FOR PROPER OPERATION.
DEPRESS EACH TRIGGER SEPARATELY. TOOL SHOULD NOT ACTIVATE. DEPRESS BOTH TRIGGERS.
TOOL SHOULD ACTIVATE.
IF TOOL HAS "ANTI-TIE DOWN" OPTION, BOTH TRIGGERS MUST BE DEPRESSED SIMULTANEOUSLY FOR
TOOL TO ACTIVATE.
2. TO PERFORM WORK, HOLD TOOL FIRMLY AT BOTH HANDLES. SQUEEZE TRIGGERS TO ACTIVATE TOOL.
3. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.
4. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.
5. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.
6. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP SAW DOWN CENTER OF BACKBONE AND
UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE.
7. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT.
8. PUSH SAW FORWARD SO THAT GUARDS, ITEMS 1 AND 2 FIGURE 1, RIDE AGAINST BEEF. THIS HELPS STEADY
SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING.

! WARNING

MAINTENANCE
ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE
AND SERVICE TO THIS TOOL.

1. TOOL REQUIRES GREASING AFTER 40 HOURS OF OPERATION. GREASE USING KENTMASTER GREASE (PART NO.
7903070).

! WARNING
! WARNING

BLADE REMOVAL AND CLEANING.

ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR
REMOVING BLADE FROM TOOL.

ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM TOOL.
1. REMOVE PAPER WRAPPER FROM BLADE.
2. OPEN COVERS, FIGURE 1, ITEMS 1,2, 3 AND 4.
3. INSTALL TORQUE WRENCH, ITEM 5, INTO SCREW, FIGURE 1, ITEM 6, AND TURN COUNTER-CLOCKWISE (CCW).
THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEMS 7 AND 8, TO RETRACT.
4. SLIDE TAKE-UP WHEEL TO RIGHT.
5. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING
AROUND AND OVER THE TAKE-UP AND DRIVE WHEELS.
6. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL
AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER
TENSION ON BLADE).
7. TWIST BLADE 90 AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING DOWNWARD.
8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, TO CHECK TRACKING OF BLADE ON WHEELS.
9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS.
AT END OF EACH SHIFT:
1. REMOVE SAW BLADE.
2. IF USING BLADE AGAIN, WASH BLADE WITH HOT WATER TO REMOVE FAT, MEAT AND BONE PARTICLES.
3. DRY AND APPLY A COAT OF MINERAL OIL TO ENTIRE SURFACE OF BLADE TO AVOID OXIDATION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

3 OF 44

REV G: 8/5/08

CLEANING AND STERILIZING SAW

AT END OF EACH SHIFT:
1. REMOVE SAW BLADE.
2. CLEAN AND WASH DOWN BOTH INSIDE AND OUTSIDE OF ENTIRE MACHINE THOROUGHLY WITH HOT WATER
AND CLEANING AGENT. AVOID USING HARSH CAUSTIC CLEANERS ON MACHINE.
3. WASH OFF ALL BONE DUST AND MEAT PARTICLES FROM INSIDE OF FRAMES, AROUND WHEELS AND GUIDES.
4. SPRAY BOTH INSIDE AND OUTSIDE OF MACHINE WITH A LIGHT COAT OF MINERAL OIL.

WATER CONNECTION
A BULKHEAD FITTING, FIGURE 1, ITEM 10, IS PROVIDED AT THE BASE OF DRIVE SIDE FRAME, ITEM 11, FOR
CONNECTION TO COLD WATER. ADJUST CONNECTOR AND NOZZLE, ITEMS 12 AND 13, TO CLEAN BONE DUST
FROM DRIVE WHEEL AND MEAT PARTICLES TRAPPED BETWEEN TEETH OF SAW BLADE. FITTING AND HOSE,
ITEMS 14 AND 15, AT BASE OF DRIVE SIDE FRAME, ARE PROVIDED FOR DRAINAGE OF WASTE WATER.

TORQUE WRENCH CALIBRATION

TORQUE WRENCH, ITEM 5, IS CALIBRATED AND PRESET TO 55 INCH/LBS AT FACTORY. PERIODICALLY CHECK
CALIBRATION BY USE OF ANOTHER TORQUE WRENCH WITH A DIAL TO MAKE ADJUSTMENT AND RESET TORQUE
WRENCH TO 55 INCH/LBS. REMOVE TORQUE WRENCH COVER TO CLEAN AND LUBRICATE PERIODICALLY.
TESTING AND SETTING OF TORQUE WRENCH:
TOOLS REQUIRED:
HEX WRENCH -- 3/16"
HEX BAR -- 1/2", ABOUT 3"-6" LONG
HEX SOCKET -- 1/2" WITH DRIVE END TO MATCH COMMERCIAL WRENCH SELECTED
TORQUE WRENCH, COMMERCIAL DIAL TYPE PREFERABLE
SCREWDRIVER -- 3/8"-7/16" FLAT BLADE
STEP 1 -- TESTING KENTMASTER TORQUE WRENCH
A. ATTACH COMMERCIAL TORQUE WRENCH TO KENTMASTER TORQUE WRENCH USING 1/2" HEX BAR AND
1/2" HEX SOCKET.
B. HOLD ASSEMBLY FIRMLY AND ROTATE KENTMASTER TORQUE WRENCH CLOCKWISE SLOWLY UNTIL
WRENCH "SLIPS".
C. INDICATOR NEEDLE ON COMMERCIAL TORQUE WRENCH SHOULD READ 55 IN/LBS 3 IN/LBS (5%).
IF OVER OR UNDER VALUE, PROCEED TO STEP 2 -- RESETTING KENTMASTER TORQUE WRENCH.
STEP 2 -- RESETTING KENTMASTER TORQUE WRENCH
A. USING 3/16" HEX WRENCH, REMOVE FOUR (4) SCREWS HOLDING THE WRENCH HANDLE IN PLACE.
REMOVE HANDLE AND GASKET. SET ALL PARTS ASIDE FOR REUSE.
B. HOLD WRENCH BODY SECURE BY EITHER CLAMPING SMALL DRIVE END IN VISE OR BY CLAMPING THE
1/2" HEX BAR IN VISE AND ATTACHING WRENCH TO BAR.

NOTE: Do not clamp body of Torque Wrench in vise as

severe damage to Torque Wrench could occur.
C. USE FLAT BLADE SCREWDRIVER TO ADJUST THE FOUR (4) SET SCREWS UNDER WRENCH HANDLE.
USE A STAGGERED PATTERN WHILE ADJUSTING, SUCH AS UPPER, LOWER, LEFT THEN RIGHT.
TO REDUCE TORQUE VALUE - BACK OFF SET SCREWS COUNTER-CLOCKWISE ABOUT 1/8 TURN EACH.
TO INCREASE TORQUE VALUE - TURN IN SET SCREWS CLOCKWISE ABOUT 1/8 TURN EACH.
D. REASSEMBLE TORQUE WRENCH WITH HANDLE AND GASKET. RETEST PER STEP 1. CONTINUE TESTING
AND SETTING UNTIL WRENCH OPERATES AT PROPER TORQUE VALUE.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

4 OF 44

REV G: 8/5/08

HANGER
THE SAW HANGER INCORPORATES TWO (2) ADJUSTMENT FEATURES. ADJUSTMENT "H" (HORIZONTAL) SHIFTS WEIGHT
OF SAW FROM FRONT TO REAR ACCORDING TO OPERATOR PREFERENCE. WEIGHT OF SAW SHOULD BE ADJUSTED SO
THAT NOSE OF SAW IS TIPPED DOWN SLIGHTLY FOR BETTER OPERATOR CONTROL. TO ADJUST, LOOSEN TWO (2)
SCREWS, ITEMS 16, AND ADJUST ACCORDINGLY.
ADJUSTMENT "V" (VERTICAL) SHIFTS WEIGHT OF SAW FROM RIGHT TO LEFT, AFFECTING BLADE PATH AND
STRAIGHTNESS OF CUT. NO ADJUSTMENT SHOULD BE REQUIRED AS MACHINES ARE ADJUSTED AT FACTORY FOR
WEIGHT DISTRIBUTION FROM SIDE TO SIDE. IF THERE IS "SOFT-SIDING" OF CARCASS RESULTING FROM BLADE
CUTTING TO LEFT OR RIGHT OF CENTERLINE, MAKE ADJUSTMENT AS FOLLOWS:
CUTTING EXCESSIVELY TO RIGHT -- WITH A 3/8" HEX WRENCH, TURN SHAFT, ITEM 17, COUNTER-CLOCKWISE.
CUTTING EXCESSIVELY TO LEFT -- WITH A 3/8" HEX WRENCH, TURN SHAFT, ITEM 17, CLOCKWISE.

TOOTH
DIRECTION

Figure 1 BM-VKENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

5 OF 44

REV G: 8/5/08

TROUBLE SHOOTING HINTS:

BE SURE DRIVE WHEEL IS TURNING COUNTER-CLOCKWISE (CCW) AND
BLADE IS INSTALLED WITH TEETH POINTED TOWARD DRIVE FRAME.
BE SURE BLADE TEETH ARE SITTING ABOVE UNDERCUT ON BOTH WHEELS
SO AS NOT TO AFFECT SET OF TEETH.

BAD SPLIT

CHECK GAP BETWEEN CARBIDE INSERTS WHICH MUST NOT BE TOO TIGHT
OR TOO LOOSE. BLADE SHOULD SLIDE THROUGH WITHOUT PLAY.
MAKE ADJUSTMENT IF NECESSARY.

UNEVEN SPLIT
REPLACE SAW BLADE IN CASE BLADE IS DEFECTIVE.
CUTS TO LEFT OR RIGHT
ADJUST SAW HANGER (ADJUSTMENT "V") IF SAW CUTS OFF CENTER TO
RIGHT OR LEFT.
ADJUST HANGER ("H" ADJUSTMENT) IF SAW NOSE RISES TOO EASILY AND
ADDITIONAL WEIGHT MUST BE SHIFTED FORWARD.
BE SURE SAW IS NOT DROPPING DOWN TOO QUICKLY. ADJUST BALANCER.
BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION.
________________________________________________________________________________________________________
CHECK IF BLADE IS BREAKING AT WELD. BLADE MAY BE DEFECTIVE.

PREMATURE BLADE
CRACKING OR BREAKING

WHEELS SLIPPING IN BLADE (EVIDENT BY VERY SHINY BLADE SURFACE).

CHECK FOR INCORRECT TORQUE SETTING. CHECK TORQUE WRENCH
CALIBRATION.
OPERATOR PUSHING SAW THROUGH BEEF EXCESSIVELY.
BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION.

CHECK FOR PROPER GAP (.025"-.028", .64-.71mm) BETWEEN CARBIDE INSERTS.

________________________________________________________________________________________________________
CHECK FOR BONE DUST BUILD-UP AT GUIDES. CLEAN OUT AND INCREASE
WATER FLOW IF NECESSARY.
CHECK IF BLADE IS SLIPPING ON WHEELS. LOOK FOR CAUSE AND CORRECT.
BLACK APPEARS
ON BACKBONE

CHECK FOR PROPER GAP (.025"-.028", .64-.71mm) BETWEEN CARBIDE INSERTS.

GAP MAY BE TOO TIGHT, CAUSING INSERTS TO MACHINE SIDES OF BLADE.
CHECK FOR CHIPPED OR CRACKED CARBIDE INSERTS AT BLADE GUARD
ASSEMBLIES. ROTATE OR REPLACE IF NECESSARY.

WITH BLADE REMOVED, CHECK TAKE-UP WHEEL TO BE SURE IT SPINS FREELY.

________________________________________________________________________________________________________
CHECK WHEELS FOR PLAY, LOOSENESS OR LOOSE SCREWS OR NUTS.
CHECK TAKE-UP WHEEL BRACKET, TIGHTEN AND CORRECT PLAY.
CHECK WHEEL BEARINGS AND REPLACE IF DEFECTIVE.
BLADE SLIPS OFF WHEELS

CHECK WHEELS FOR ROUNDNESS AND WEAR. BE SURE WHEEL FACES ARE
NOT TAPERED OR HAVE FLAT SPOTS DUE TO WEAR. REPLACE IF DEFECTIVE.
CHECK TAKE-UP WHEEL FOR PROPER TORQUE SETTING.
LOOK FOR ANY BLADE OBSTRUCTIONS.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

6 OF 44

REV G: 8/5/08
CHANGE SAW BLADE. BLADE MAY BE DEFECTIVE.

REMOVE BLADE FROM MACHINE. BACK OFF SCREW, ITEM 6, WITH TORQUE
WRENCH. GRAB TAKE-UP WHEEL WITH BOTH HANDS AND SLIDE BACK AND
MOTOR PULLS EXCESSIVE
FORTH. IT SHOULD SLIDE FREELY. IF IT BINDS OR TAKES EXCESSIVE EFFORT,
DISASSEMBLE COMPLETELY. CHECK TO SEE IF GIBS LOCATED ON EACH SIDE
AMPERAGE (WITHOUT LOAD)
OF SLIDE ARE TOO CLOSE AND TIGHT AGAINST SLIDE. LOOSEN SCREWS THAT
OR
HOLD GIB IN PLACE. SPREAD GIBS SLIGHTLY OUT AND RETIGHTEN SCREWS.
BLADE IS TOO LOOSE WHILE
SLIDE SHOULD MOVE BACK AND FORTH FREELY, BUT WITHOUT UP AND DOWN
TORQUE WRENCH IS
PLAY. REASSEMBLE AND TEST MACHINE. LUBRICATE SURFACES BETWEEN
PROPERLY CALIBRATED
SLIDE AND GIB.
________________________________________________________________________________________________________

SERVICE
1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN PREVENTIVE MAINTENANCE PROGRAM.
2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.
3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE INFORMATION.

PARTS BOOK
MODELS MAIN ASSEMBLIES
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

7 OF 44

REV G: 8/5/08

Figure 2 MODELS BM-V-SDB AND BM-V-SD

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

8 OF 44

REV G: 8/5/08
1730000:BM-V-SDB / 1708100: BM-V-SD
ITEM
1

3
4
5
6
7
8
9
10

11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

PART #
OPTIONS
OPTIONS
1720000
1720010
1720020
1720030
1720007
4501610
1700900
1709790
1709890
1710897
1704130
1704220
1705590
1704150
1704430
1705850
1707340
1707350
1708420
1708430
1708460
1708500
1708610
1708840
1709199
1709196
1709620
1709630
1710070
1730011
1709197
3000090
3001090
3200080
3316050
4111000
4111020
7000020
7240710
7300200
7681530
7681650
7798170
7798220
8607060
9211050
9215080
9215100
9239050
9243080
9413070

DESCRIPTION
2HP MOTOR ASSEMBLY
3HP MOTOR ASSEMBLY
POWER SUPPLY, 42V, ANTI-TIE DOWN
POWER SUPPLY, 42V, NO ANTI-TIE DOWN
POWER SUPPLY, NON 42V, ANTI-TIE DOWN
POWER SUPPLY, NON 42V, NO ANTI-TIE DOWN
POWER SUPPLY, SINGLE PHASE, 115V / 230V
WRENCH / TOOL
TORQUE WRENCH / TOOL
WRENCH, ADJUSTMENT / TOOL
SPRAY TUBE ASSEMBLY / OPTIONAL
EXTERNAL SPRAY NOZZLE
CAP
GASKET
GEAR, DRIVE / USE WITH 2HP MOTOR 50/60 Hz
GEAR, DRIVE / USE WITH 3HP MOTOR 60Hz
GEAR, DRIVE / USE WITH 3HP MOTOR 50Hz
GEAR, DRIVEN / USE WITH 2HP MOTOR 50/60 Hz
GEAR, DRIVEN / USE / WITH 3HP MOTOR 60Hz
GEAR, DRIVEN / USE WITH 3HP MOTOR 50Hz
BEAM
COVER
COVER, GEAR
DRIVE WHEEL ASSEMBLY
COVER
FITTING
DRIVE SIDE ASSEMBLY / BM-V-SDB
DRIVE SIDE ASSEMBLY / BM-V-SD
FLANGE
SHAFT
NUT
TAKE-UP SIDE ASSEMBLY / BM-V-SDB
TAKE-UP SIDE ASSEMBLY / BM-V-SD
LOCKWASHER
LOCKNUT
BEARING
BEARING
BLADE / BM-V-SDB
BLADE / BM-V-SD
PLUG
WINDOW
DISCHARGE HOSE
O-RING
O-RING
SEAL
SEAL
KEY
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW

QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
10
6
5
10
1
3

Figure 3 BOM FOR MODELS BM-V-SDB AND BM-V-SD

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

9 OF 44

REV G: 8/5/08

Figure 4 MODEL BM-V-S

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

10 OF 44

REV G: 8/5/08

1708000: BM-V-S
ITEM
1

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

PART #

DESCRIPTION

OPTIONS
OPTIONS
1720000
1720010
1720020
1720030
4501610
1700900
1709790
1709890
1710897
1704150
1704430
1707340
1707350
1704130
1704220
1708420
1708430
1708460
1708500
1708610
1708840
1709192
1709194
1709620
1709630
1710070
3000090
3001090
3200080
3316050
4111030
7000020
7240710
7300200
7681530
7681650
7798170
7798220
8607060
9211050
9215080
9215100
9239050
9243080
9413070

3HP MOTOR ASSEMBLY

5HP MOTOR ASSEMBLY
POWER SUPPLY, 42V, ANTI-TIE DOWN
POWER SUPPLY, 42V, NO ANTI-TIE DOWN
POWER SUPPLY, NON 42V, ANTI-TIE DOWN
POWER SUPPLY, NON 42V, NO ANTI-TIE DOWN
WRENCH / TOOL
TORQUE WRENCH / TOOL
WRENCH, ADJUSTMENT / TOOL
SPRAY TUBE ASSEMBLY / OPTIONAL
EXTERNAL SPRAY NOZZLE
GEAR, DRIVE / FOR 60Hz FREQUENCY
GEAR, DRIVE / FOR 50Hz FREQUENCY
GEAR, DRIVEN / FOR 60Hz FREQUENCY
GEAR, DRIVEN / FOR 50Hz FREQUENCY
CAP
GASKET
BEAM
COVER
COVER, GEAR
DRIVE WHEEL ASSEMBLY
COVER
FITTING
DRIVE SIDE ASSEMBLY
TAKE-UP SIDE ASSEMBLY
FLANGE
SHAFT
NUT
LOCKWASHER
LOCKNUT
BEARING
BEARING
BLADE
PLUG
WINDOW
DISCHARGE HOSE
O-RING
O-RING
SEAL
SEAL
KEY
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW

QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
10
6
5
10
1
3

Figure 5 BOM FOR MODEL BM-V-S

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

11 OF 44

REV G: 8/5/08

Figure 6 MODEL BM-V-SB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

12 OF 44

REV G: 8/5/08
1708050: BM-V-SB
ITEM
1

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

PART #
OPTIONS
OPTIONS
1720000
1720010
1720020
1720030
4501610
1700900
1709790
1709910
1710897
1705150
1704150
1705770
1707340
1704130
1704220
1708460
1708610
1708790
1708805
1708820
1708840
1709505
1709600
1709620
1709630
1710070
3000090
3001090
3200080
3316050
4111100
7000020
7240710
7300200
7681530
7681650
7798170
7798220
8607060
9211050
9215080
9215100
9239050
9243080
9413070

DESCRIPTION
3HP MOTOR ASSEMBLY
5HP MOTOR ASSEMBLY
POWER SUPPLY, 42V, ANTI-TIE DOWN
POWER SUPPLY, 42V, NO ANTI-TIE DOWN
POWER SUPPLY, NON 42V, ANTI-TIE DOWN
POWER SUPPLY, NON 42V, NO ANTI-TIE DOWN
WRENCH / TOOL
TORQUE WRENCH / TOOL
WRENCH, ADJUSTMENT / TOOL
SPRAY TUBE ASSEMBLY / OPTIONAL
EXTERNAL SPRAY
GEAR, DRIVE / FOR 60Hz FREQUENCY
GEAR, DRIVE / FOR 50Hz FREQUENCY
GEAR, DRIVEN / FOR 60Hz FREQUENCY
GEAR, DRIVEN / FOR 50Hz FREQUENCY
CAP
GASKET
COVER, GEAR
COVER
DRIVE WHEEL ASSEMBLY
DRIVE SIDE ASSEMBLY
BEAM
FITTING
TAKE-UP SIDE ASSEMBLY
COVER
FLANGE
SHAFT
NUT
LOCKWASHER
LOCKNUT
BEARING
BEARING
BLADE
PLUG
WINDOW
DISCHARGE HOSE
O-RING
O-RING
SEAL
SEAL
KEY
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW

QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
10
6
5
10
1
3

Figure 7 BOM FOR MODEL BM-V-SB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

13 OF 44

REV G: 8/5/08

TAKE-UP SIDE ASSEMBLY

Figure 8 TAKE-UP SIDE ASSEMBLY

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

14 OF 44

REV G: 8/5/08

ITEM

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

PART #

1704560
1709590
1704670
1704710
1709570
1704780
1709550
1704790
1706360
1704800
1704810
1709560
1708470
1708490
1708930
1708530
1708710
1730220
1708560
1709530
1708570
1708590
1708600
1708900
1730230
1709090
1709340
1709500
1708410
1708850
1730210
3000080
3001500
3005280
3650590
3650960
4505020
5001250
7018150
9211050
9213080
9239030
9239050
9241030
9241050
9333000
9333070
9500090

TAKE-UP SIDE ASSEMBLY

1730011

1709197

1709194

1709505

DESCRIPTION

QTY
MODEL
BM-V-SDB

QTY
MODEL
BM-V-SD

QTY
MODEL
BM-V-S

QTY
MODEL
BM-V-SB

1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
6
4
3
3
6
3
1
2
3

1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
6
4
3
3
6
3
1
2
3

1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
10
4
4
4
6
3
1
2
4

1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
10
4
4
4
6
3
1
2
4

HINGE ASSEMBLY
HINGE ASSEMBLY
KNOB
PLATE
PLATE
GIB
GIB
HOLDER, SHAFT
HOLDER, SHAFT
INSERT, ADJUSTABLE SCREW
SPACER
SPACER
SHAFT
SLIDE
SLIDE
WHEEL, TAKE-UP
WHEEL, TAKE-UP
WHEEL, TAKE-UP
SCREW, ADJUSTABLE
SCREW, ADJUSTABLE
BLOCK, SLIDE
CATCH
COVER
COVER
COVER
BLADE GUIDE ASSEMBLY
BLADE GUIDE ASSEMBLY
FRAME, TAKE-UP SIDE
FRAME, TAKE-UP SIDE
FRAME, TAKE-UP SIDE
FRAME, TAKE-UP SIDE
LOCKWASHER
LOCKNUT
NILOS RING
BEARING CUP
TAPER BEARING CONE
LABEL, DANGER/WARNING
RETAINING RING
FITTING - LUBE
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SET SCREW
SET SCREW
NUT

TAKE-UP WHEEL ADJUSTMENT

TAKE-UP WHEEL, ITEM 10, MUST TURN FREELY BUT WITHOUT EXCESSIVE PLAY OR LOOSENESS. ELIMINATE
EXCESSIVE PLAY BY TIGHTENING NUT, ITEM 18, AT CENTAR OF TAKE-UP WHEEL.

Figure 9 TAKE-UP SIDE ASSEMBLY BOM

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

15 OF 44

REV G: 8/5/08

DRIVE SIDE ASSEMBLY

Figure 10 DRIVE SIDE ASSEMBLY

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

16 OF 44

DRIVE SIDE ASSEMBLY

ITEM

PART #

1
2

1704300
1704330
1704650
1705540
1704660
1705560
1704670
1708550
1708590
1708690
1708780
1708990
1709380
1709000
1709390
1709101
1709100
1709130
1709193
1709370
1708400
1708800
1709661
1709771
1709770
1709772
1709780
1709860
ASSEMBLY
1710032
2000020
2000080
2000130
2000140
2000700
2000730
4505030
5001250
7001270
7003650
7004400
7007730
7011230
7011530
7011650
7034070
7034090
7036150

3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39

DESCRIPTION

ADJUSTING SCREW
NUT, ADJUSTING SCREW
HINGE ASSEMBLY
HINGE ASSEMBLY
SPACER, HINGE
SPACER, HINGE
KNOB
FLANGE, REAR
CATCH
COVER, DRIVE SIDE
COVER, DRIVE SIDE
GASKET
GASKET
SWITCH COVER
SWITCH COVER
BLADE GUIDE ASSEMBLY
BLADE GUIDE ASSEMBLY
TOP HANDLE WITH SWITCH
REAR HANDLE ASSEMBLY
FRAME, DRIVE SIDE
FRAME, DRIVE SIDE
FRAME, DRIVE SIDE
TUBE
BAR HANGER
BAR HANGER
SPACER
HANGER
WASHER
1710030
BEARING
3706400
BEARING
BOOT, PUSH BUTTON
LOCKNUT
ON-OFF PLATE
BOOT, TOGGLE SWITCH
SWITCH
SWITCH
LABEL, ELECTRIC ARROW
RETAINING RING
BULKHEAD COUPLING
PIPE BUSHING
TEE
MALE BRANCH TEE
CONNECTOR
CONNECTOR
SPRAY NOZLE
MALE PLUG
SOCKET
FITTING

1709199

1709196

1709192

REV G: 8/5/08
1708805

QTY
MODEL
BM-V-SDB

QTY
MODEL
BM-V-SD

QTY
MODEL
BM-V-S

QTY
MODEL
BM-V-SB

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
2
1
1
2

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

17 OF 44

40
41
42
43

54
55
56
57
58

7036450
7300754
8250180
8348080
8418180
8418160
8462080
8500200
8505180
8506180
8622500
9050020
9050040
9209050
9215120
9245060
9239050
9241050
9245060
9333000
9500090

ITEM

PART #

44
45
46
47
48
49
50
51
52
53

ELBOW
TUBE
SCREW
SET SCREW
SCREW
SCREW
ANCHOR SHACKLE
NUT
WASHER
WASHER
DOWEL PIN
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SET SCREW
NUT
DESCRIPTION

DRIVE SIDE ASSEMBLY

REV G: 8/5/08
1
1
1
2
2
1
2
2
2
2
5
4
4
1
5
1
1
1
5

1
1
1
2
2
1
2
2
2
2
5
4
4
1
5
1
1
1
5

1
1
1
2
2
1
2
2
2
2
5
4
4
1
5
1
1
1
5

1
1
1
2
2
1
2
2
2
2
5
4
4
1
5
1
1
1
5

QTY
MODEL
BM-V-SDB

QTY
MODEL
BM-V-SD

QTY
MODEL
BM-V-S

QTY
MODEL
BM-V-SB

1709199

1709196

1709192

1708805

Figure 11 DRIVE SIDE ASSEMBLY BOM

TRANSMISSION

REFERENCE: MODEL BM-V-S

FIGURE 3

Figure 12 TRANSMISSION OVERVIEW

TRANSMISSION AND SPEED REDUCTION GEARS ARE LOCATED BEHIND DRIVE WHEEL AND CAN BE SERVICED
BY OPENING DRIVE WHEEL COVER. A ROUND GLASS SIGHT GAGE IS LOCATED BEHIND DRIVE WHEEL AND CAN
BE VIEWED WITHOUT WHEEL REMOVAL. A PLUG IS LOCATED BELOW THE SIGHT GAGE FOR DRAINING AND
ANOTHER ABOVE FOR FILLING WITH OIL. PERIODICALLY CHECK OIL LEVEL AND ADD OIL IF LEVEL BELOW
SIGHT GAGE WITH SAW IN HORIZONTAL POSITION. IF OIL LOOKS CONTAMINATED WITH WATER, GRITTY OR
BROKEN DOWN, DRAIN AND REFILL TO ABOVE SIGHT GAGE WITH HIGH QUALITY GEAR LUBRICANT. WE
RECOMMEND MOBILUBE HD 80W-90 SAE 80W-90 GEAR LUBRICANT, MULTI-PURPOSE. TRANSMISSION SHOULD
BE FLUSHED OUT AND REFILLED AFTER EVERY 200 HOURS OF OPERATION, AND WHEN OPENED UP FOR
MAINTENANCE. THE GEAR LUBRICANT USED SHOULD ALSO BE USED FOR FLUSHING OUT TRANSMISSION.
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

18 OF 44

REV G: 8/5/08

BLADE GUIDE ASSEMBLY, TAKE-UP SIDE

1709090: BLADE GUIDE ASSEMBLY, FRONT

ITEM

PART #

1
2
3
4
5
6
7
8
9
10
11
12

1708630
1708640
1708650
1709110
8865050
8895100
9211050
9213100
8239050
9501430
9620450
9870340

DESCRIPTION
GUIDE HOLDER
REAR GUARD
FRONT GUARD
GUIDE
CARBID INSERT
BALL PLUNGER
SCREW
SCREW
SCREW
NUT
PIN
SCREW

QTY
1
1
1
2
3
1
2
2
7
1
1
1

Figure 13 BLADE GUIDE ASSEMBLY, FRONT (BM-V-S & SB)

BLADE GUARD ADJUSTMENTS
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

19 OF 44

REV G: 8/5/08
BLADE GUARD CONSISTS OF TWO (2) CARBIDE INSERTS, ITEM 5 FIGURE 13, THROUGH WHICH THE BLADE
PASSES, AND A BACK-UP INSERT LOCATED JUST ABOVE THE BLADE. THE INSERTS SHOULD BE CLEANED DAILY
AND INSPECTED PERIODICALLY FOR WEAR AND PROPER GAP WIDTH. THE INSERTS MAY BE ROTATED UNTIL
ALL FOUR (4) SIDES ARE WORN, AND THEN TURNED OVER FOR AN ADDITONAL FOUR (4) SIDES. THE BACK-UP
INSERT SHOULD BE ROTATED WHEN A GROOVE IS WORN INTO IT OR WEAR IS APPARENT.
GAP ADJUSTMENT:
1. REMOVE FOUR (4) SCREWS, ITEM 9, FIGURE 13.
2. CLEAN, LUBRICATE AND ROTATE OR REPLACE INSERTS.
THERE ARE TWO (2) FIBER GUIDES, ITEM 4, LOCATED UNDER INSERTS. THEY HELP KEEP BLADE FROM BEING
PULLED OUT OF GAP. REPLACE GUIDES IF EXCESSIVELY WORN.
WITH SAW IN FREE RUNNING CONDITION, CHECK BLADE'S VERTICAL LOCATION BETWEEN INSERTS.
PROPER LOCATION IS TOP OF BLADE JUST TOUCHING BACK-UP INSERT.
VERTICAL ADJUSTMENT:
1. LOOSEN TWO (2) SCREWS, ITEM 8.
2. SLIDE BLADE GUARD UP OR DOWN AS NEEDED.
3. RETIGHTEN SCREWS.

1709340:BLADE GUIDE ASSEMBLY, FRONT

ITEM

PART #

1
2
3
4

1708630
8865050
9213100
9239050

DESCRIPTION
GUIDE HOLDER
CARBID INSERT
SCREW
SCREW

QTY
1
3
2
3

Figure 14 BLADE GUIDE ASSEMBLY, FRONT (BM-V-SDB & SD)

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

20 OF 44

REV G: 8/5/08

BLADE GUIDE ASSEMBLY, DRIVE SIDE

1709100 (BM-V-SB, S, SD), 1709101 (BM-V-SDB): BLADE GUIDE ASSEMBLY, REAR

ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13

PART #
1708660
1708661
1709110
1709750
1709760
8239050
8865050
8895100
9211050
9213110
9239050
9501430
9620450
9870340

DESCRIPTION
GUIDE HOLDER / FOR 1709100 (BM-V-SB, S, SD)
GUIDE HOLDER / FOR 1709101 (BM-V-SDB)
GUIDE
REAR GUARD
FRONT GUARD
SCREW
CARBID INSERT
BALL PLUNGER
SCREW
SCREW
SCREW
NUT
PIN
SCREW

QTY
1
1
2
1
1
4
3
1
2
2
3
1
1
1

REFER TO BLADE GUIDE ASSEMBLY, TAKE-UP SIDE (FIGURE 13) FOR ADJUSTMENT INSTRUCTIONS.

Figure 15 BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-S, SB, SD, SDB)
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

21 OF 44

REV G: 8/5/08

HANDLES

1709130: TOP HANDLE ASSEMBLY

ITEM

PART #

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13

1302430
1302440
1302450
1302460
1302470
1701550
1708950
2000690
7036450
7300753
9045020
9213140
9213190

TRIGGER
SPRING
PLUNGER
HOLDER, PLUNGER
HOLDER
SPRING
HANDLE
SWITCH
ELBOW
TUBE
SCREW
SCREW
SCREW

QTY
1
1
1
1
2
2
1
1
1
1
4
1
1

Figure 16 TOP HANDLE ASSEMBLY

1709193: REAR HANDLE ASSEMBLY

ITEM

PART #

1
2
3
4
5
6

1708540
1709640
1710010
8409240
8613180
8890010

DESCRIPTION
HANDLE TRIGGER
REAR HANDLE, TRIGGER
REAR HANDLA FRAME
SCREW
ROLL PIN
SPRING

QTY
1
1
1
1
1
2

Figure 17 REAR HANDLE ASSEMBLY

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

22 OF 44

REV G: 8/5/08

ADDITIONAL SPRAY OPTIONS

1709890: SPRAY TUBE UNDER BEAM ASSEMBLY(BM-V-SDB, SD, S)
1709910: SPRAY TUBE UNDER BEAM ASSEMBLY (BM-V-SB)
ITEM

PART #

1709870
1709880
1709900
7001110
7003110
7034070
7034090
7036560
8413120

2
3
4
5
6
7
8

DESCRIPTION

QTY

BRACKET
TUBE, FOR BM-V-SDB, SD, S
TUBE, FOR BM-V-SB
COUPLING
ELBOW COUPLING
MALE PLUG
SOCKET
ELBOW
SCREW

1
1
1
1
1
1
1
1
1

Figure 18 SPRAY TUBE UNDER BEAM ASSEMBLY

1710897: EXTERNAL SPRAY NOZLE

ITEM

PART #

DESCRIPTION

QTY

1
2
3
4
5
6
7
8

1709870
7000410
7003010
7003650
7011650
7034070
7034090
8413120

BRACKET
ELBOW
ELBOW
PIPE BUSHING
SPRAY NOZLE
MALE PLUG
SOCKET
SCREW

1
1
1
1
1
1
1
1

Figure 19 1710897: EXTERNAL SPRAY NOZZLE

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

23 OF 44

REV G: 8/5/08

MOTOR ASSEMBLY
1703321
1703320
1703310
Rotor Shaft Assy

1703300
1703300
1703300
Motor Shaft

2340670
2340630
2340620
Rotor

BM-V: 2HP MOTOR

ITEM

PART #

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

OPTIONS
1501800
1705620
OPTIONS
1703330
3522060
3524050
5002120
5002440
5100980
5101180
7681300
7902170
9313040
9411100
9507100

DESCRIPTION
STATOR, CHART BELOW
COVER, MOTOR HOUSING
KEY
ROTOR-SHAFT ASSEMBLY
MOTOR HOUSING
BEARING
BEARING
RETAINING RING
RETAINING RING
RETAINING RING
RETAINING RING
O-RING
EXPANSION PLUG
SET SCREW
SCREW
WASHER

MOTOR ASS'Y 230V, 2HP, 1PH, 50HZ, 12.2AMPS

MOTOR ASS'Y 115V, 2HP, 1PH, 50HZ, 24.4AMPS
MOTOR ASS'Y 230V, 2HP, 1PH, 60HZ, 11.7AMPS
MOTOR ASS'Y 115V, 2HP, 1PH, 60HZ, 23.4AMPS
MOTOR ASS'Y 42V, 2HP, 3PH, 50HZ, 36.0 AMPS
MOTOR ASS'Y 380V, 2HP, 3PH, 50HZ, 3.7 AMPS
MOTOR ASS'Y 220V, 2HP, 3PH, 50HZ, 6.4 AMPS
MOTOR ASS'Y 416V, 2HP, 3PH, 50HZ, 3.3 AMPS
MOTOR ASS'Y 208V, 2HP, 3PH, 50HZ, 6.6 AMPS
MOTOR ASS'Y 230V, 2HP, 3PH, 50HZ, 6.6 AMPS
MOTOR ASS'Y 115V, 2HP, 3PH, 50HZ, 13.2 AMPS
MOTOR ASS'Y 550V, 2HP, 3PH, 60HZ, 2.5AMPS
MOTOR ASS'Y 380V, 2HP, 3PH, 60HZ, 3.9 AMPS
MOTOR ASS'Y 220V, 2HP, 3PH, 60HZ, 6.8 AMPS
MOTOR ASS'Y 460V, 2HP, 3PH, 60HZ, 3.3 AMPS
MOTOR ASS'Y 230V, 2HP, 3PH, 60HZ, 6.6 AMPS
MOTOR OPTION DESCRIPTION

QTY
1
1
1
1
1
1
1
1
2
1
1
1
1
2
4
4
1703470-230-150
1703470-115-150
1703460-230-160
1703460-115-160
1703400
1703420-380-350
1703420-220-350
1703430-416-350
1703430-208-350
1703410-230-350
1703410-115-350
1703450
1703440-380-360
1703440-220-360
1703430-460-360
1703430-230-360
MOTOR ASS'Y

2340270
2340270
2340260
2340260
2340200
2340220
2340220
2340230
2340230
2340210
2340210
2340250
2340240
2340240
2340230
2340230
STATOR

1703321
1703321
1703320
1703320
1703310
1703310
1703310
1703310
1703310
1703310
1703310
1703310
1703310
1703310
1703310
1703310
ROTOR

BM-V: 2HP MOTOR ASSEMBLY OPTIONS with STATOR

Figure 20 2HP MOTOR OPTIONS

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

24 OF 44

REV G: 8/5/08

1703350
Rotor Shaft Assy

1703340
Motor Shaft

2340610
Rotor

BM-V: 3HP MOTOR

ITEM

PART #

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

OPTIONS
1501800
1705620
1703350
1703360
3522060
3524050
5002120
5002440
5100980
5101180
7681300
7902170
9313040
9411100
9507100

DESCRIPTION
STATOR, CHART BELLOW
COVER, MOTOR HOUSING
KEY
ROTOR-SHAFT ASSEMBLY
MOTOR HOUSING
BEARING
BEARING
RETAINING RING
RETAINING RING
RETAINING RING
RETAINING RING
O-RING
EXPANSION PLUG
SET SCREW
SCREW
WASHER

QTY
1
1
1
1
1
1
1
1
2
1
1
1
1
2
4
4

MOTOR ASS'Y 42V, 3HP, 3PH, 50HZ, 47.0 AMPS

1703500
MOTOR ASS'Y 380V, 3HP, 3PH, 50HZ, 5.1 AMPS
1703520-380-350
MOTOR ASS'Y 220V, 3HP, 3PH, 50HZ, 8.8 AMPS
1703520-220-350
MOTOR ASS'Y 416V, 3HP, 3PH, 50HZ, 4.3 AMPS
1703530-416-350
MOTOR ASS'Y 208V, 3HP, 3PH, 50HZ, 8.6 AMPS
1703530-208-350
MOTOR ASS'Y 230V, 3HP, 3PH, 50HZ, 8.8 AMPS
1703510-230-350
MOTOR ASS'Y 115V, 3HP, 3PH, 50HZ, 17.6 AMPS
1703510-115-350
MOTOR ASS'Y 550V, 3HP, 3PH, 60HZ, 3.8AMPS
1703550
MOTOR ASS'Y 380V, 3HP, 3PH, 60HZ, 5.0 AMPS
1703540-380-360
MOTOR ASS'Y 220V, 3HP, 3PH, 60HZ, 8.6 AMPS
1703540-220-360
MOTOR ASS'Y 460V, 3HP, 3PH, 60HZ, 4.1 AMPS
1703530-460-360
MOTOR ASS'Y 230V, 3HP, 3PH, 60HZ, 8.2 AMPS
1703530-230-360
MOTOR OPTION DESCRIPTION
MOTOR ASS'Y
BM-V: 3HP MOTOR ASSEMBLY OPTIONS with STATOR

2340100
2340120
2340120
2340130
2340130
2340110
2340110
2340150
2340140
2340140
2340130
2340130
STATOR

1703350
1703350
1703350
1703350
1703350
1703350
1703350
1703350
1703350
1703350
1703350
1703350
ROTOR

Figure 21 3HP MOTOR OPTIONS

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

25 OF 44

REV G: 8/5/08

1703380
Rotor Shaft Assy

1703370
Motor Shaft

2340600
Rotor

BM-V: 5HP MOTOR

ITEM

PART #

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

OPTIONS
1501800
1705620
1703380
1703390
3522060
3524050
5002120
5002440
5100980
5101180
7681300
7902170
9313040
9411100
9507100

DESCRIPTION
STATOR, CHART BELOW
COVER, MOTOR HOUSING
KEY
ROTOR-SHAFT ASSEMBLY
MOTOR HOUSING
BEARING
BEARING
RETAINING RING
RETAINING RING
RETAINING RING
RETAINING RING
O-RING
EXPANSION PLUG
SET SCREW
SCREW
WASHER

QTY
1
1
1
1
1
1
1
1
2
1
1
1
1
2
4
4

MOTOR ASS'Y 550V, 5HP, 3PH, 60HZ, 5.6 AMPS

1703650
MOTOR ASS'Y 380V, 5HP, 3PH, 60HZ, 7.8AMPS
1703640-380-360
MOTOR ASS'Y 220V, 5HP, 3PH, 60HZ, 14.7AMPS
1703640-220-360
MOTOR ASS'Y 380V, 5HP, 3PH, 50HZ, 7.7 AMPS
1703620-380-350
MOTOR ASS'Y 220V, 5HP, 3PH, 50HZ, 13.4 AMPS
1703620-220-350
MOTOR ASS'Y 42V, 5HP, 3PH, 50HZ, 73.0 AMPS
1703600
MOTOR ASS'Y 460V, 5HP, 3PH, 60HZ, 6.5 AMPS
1703630-460-360
MOTOR ASS'Y 230V, 5HP, 3PH, 60HZ, 13.0 AMPS
1703630-230-360
MOTOR ASS'Y 230V, 5HP, 3PH, 50HZ, 13.6 AMPS
1703610-230-350
MOTOR ASS'Y 115V, 5HP, 3PH, 50HZ, 27.2 AMPS
1703610-115-350
MOTOR OPTION DESCRIPTION
MOTOR ASS'Y
BM-V: 5HP MOTOR ASSEMBLY OPTIONS with STATOR

2340050
2340040
2340040
2340020
2340020
2340000
2340030
2340030
2340010
2340010
STATOR

1703380
1703380
1703380
1703380
1703380
1703380
1703380
1703380
1703380
1703380
ROTOR

Figure 22 5HP MOTOR OPTIONS

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

26 OF 44

REV G: 8/5/08

POWER SUPPLY OPTIONS

1720000: POWER SUPPLY, 42V, ATD

ITEM

PART #

DESCRIPTION

1
2
3
4
5
6
7

1708730
1709480
2001090
2008200
2008210
2009120
9209240

QTY

GASKET
COVER, WIRE BOX, 42V, ATD
POWER CORD
CABLE CONNECTOR
CORD GRIP
TIMER
SCREW

1
1
1
1
1
1
4

Figure 23 POWER SUPPLY, 42V, with ANTI-TIEDOWN

1720010: POWER SUPPLY, 42V, NO ATD

ITEM

PART #

1
2
3
4
5
6

1708730
1709480
2007030
2008200
2008210
9209240

DESCRIPTION
GASKET
COVER, WIRE BOX
POWER CORD
CABLE CONNECTOR
CORD GRIP
SCREW

QTY
1
1
1
1
1
4

Figure 24 POWER SUPPLY, 42V, without ANTI-TIEDOWN

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

27 OF 44

REV G: 8/5/08

1720020: POWER SUPPLY, NON 42V, ANTI-TIE DOWN

ITEM

PART #

1
2
3
4
5
6
7
8
9

1708730
1709460
2001080
2001610
2001620
2008180
2008220
2009120
9209240

DESCRIPTION

QTY

GASKET
COVER, WIRE BOX
POWER CORD
SOCKET, MALE
SOCKET, FEMALE
CABLE CONNECTOR
CORD GRIP
TIMER
SCREW

1
1
1
1
1
1
1
1
4

Figure 25 POWER SUPPLY, NON 42V, with ANTI-TIEDOWN

2001240

2001610

1720030: POWER SUPPLY, NON 42V, NO ATD

ITEM

PART #

1
2
3
4
5
6
7

1000050
1708730
1709460
2001620
2008180
2008220
9209240

DESCRIPTION
POWER CORD w/MALE PLUG
GASKET
COVER, WIRE BOX
SOCKET, FEMALE
CABLE CONNECTOR
CORD GRIP
SCREW

QTY
1
1
1
1
1
1
4

POWER CORD 1000050: POWER CORD 20 FT LONG (2001240) + MALE PLUG (2001610)

Figure 26 POWER SUPPLY, NON 42V, without ANTI-TIEDOWN

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

28 OF 44

REV G: 8/5/08

1720007: POWER SUPPLY, SINGLE PHASE 115 / 230V

ITEM

PART #

DESCRIPTION

QTY

1
2
3
4
5
6
7
8
9
10
11

1708730
1709460
2001080
2001610
2001620
2008180
2008220
2309040
2309650
2309660
9209240

GASKET
COVER, WIRE BOX
POWER CORD
PLUG, MALE
SOCKET, FEMALE
CABLE CONNECTOR
CORD GRIP
CAPACITOR START MOTOR
START CAPACITOR 540-648 MFD
RUN CAPACITOR 50MFD
SCREW

1
1
1
1
1
1
1
1
1
1
4

Figure 27 POWER SUPPLY, SINGLE PHASE, 115 / 230V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

29 OF 44

REV G: 8/5/08

WIRING DIAGRAMS

CONTROL VOLTAGE
220V
220V

SINGLE PHASE 230V

MOTOR OPTION
MOTOR 220V, 60HZ, 11.7AMPS, 2HP
MOTOR 220V, 50HZ, 12.2AMPS, 2HP

3-POLE
CONTACTOR
2020033
2020033

OVERLOAD RELAY
2309170
2309170

NOTES:
1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.
2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
3. THE CAPACITOR AND THE SWITCH CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL
BOX.
4. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.
5. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.
6. TO REVERSE DIRECTION, REVERSE MOTOR WIRES #5 AND #8.

Figure 28 WIRING DIAGRAM SINGLE PHASE 230V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

30 OF 44

REV G: 8/5/08

CONTROL VOLTAGE
115V
115V

SINGLE PHASE 115V

MOTOR OPTION
3-POLE CONTACTOR
MOTOR 115V, 60HZ, 23.4AMPS, 2HP
2020038
MOTOR 115V, 50HZ, 24.4AMPS, 2HP
2020038

OVERLOAD RELAY
2309200
2309200

NOTES:
1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.
2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
3. THE CAPACITOR AND THE SWITCH CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL
BOX.
4. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.
5. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.
6. TO REVERSE DIRECTION, REVERSE MOTOR WIRES #5 AND #8.

Figure 29 WIRING DIAGRAM SINGLE PHASE 115V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

31 OF 44

REV G: 8/5/08

1.
2.
3.

DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.
Figure 30 WIRING DIAGRAM 3 PHASE DIFFERENT CONTROL AND MOTOR VOLTAGE
without Anti-Tie Down
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

32 OF 44

REV G: 8/5/08

1.
2.
3.

DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.
Figure 31 WIRING DIAGRAM 3 PHASE SAME CONTROL AND MOTOR VOLTAGE without
Anti-Tie Down

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

33 OF 44

REV G: 8/5/08

1.
2.
3.

DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.
Figure 32 WIRING DIAGRAM 3 PHASE DIFFERENT CONTROL AND MOTOR VOLTAGE
with Anti-Tie Down
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

34 OF 44

REV G: 8/5/08

1.
2.
3.

DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.
THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.
Figure 33 WIRING DIAGRAM 3 PHASE SAME CONTROL/TRIGGER AND MOTOR VOLTAGE
with Anti-Tie Down
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

35 OF 44

REV G: 8/5/08

Figure 34 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

36 OF 44

REV G: 8/5/08

[ENGLISH]

GENERAL INFORMATION

MODELS

BM-V-SB CARCASS SPLITTING SAW (1708050)

BM-V-S CARCASS SPLITTING SAW (1708000)
BM-V-SD CARCASS SPLITTING SAW (1708100)
BM-V-SDB CARCASS SPLITTING SAW (1730000)
________________________________________________________________________________
SERVICE CENTERS
KENTMASTER LTD. (U.K)

KENTMASTER MFG. CO., INC.

16 AVONBANK INDUSTRIAL CENTRE

WEST TOWN ROAD
AVONMOUTH - BRISTOL BS11 9DE
UNITED KINGDOM

1801 SOUTH MOUNTAIN AVE.

MONROVIA, CALIFORNIA 91016
UNITED STATES OF AMERICA

TELEPHONE: ++ 44- (0) 117- 9235035

 TELEPHONE: (626) 359-8888

FAX: ++ 44- (0) 117- 9829010

FAX: (626) 303-5151

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888 FAX: (626) 303-5151

37 OF 44

REV G: 8/5/08

NOTICE TO EMPLOYER AND PURCHASER OF TOOL

NOTICE TO SAFETY DIRECTOR
You have purchased a powerful tool that, if misused, can cause severe
injury and harm to your employees. You must instruct your employees in
the safe and proper use of this tool and to follow the safety procedures
and instructions that have been supplied by the manufacturer of this tool.
Please follow the following instructions.

1. Instruct tool operators to test the tool each day before using it to be sure it does not malfunction.
Remove and repair any tool that malfunctions.
2. Instruct tool operators to immediately stop using a tool that malfunctions or is defective.
3. Instruct personnel to immediately remove all tools that malfunction. Be sure to disconnect tool from
power supply.
4. Instruct all personnel to stay clear of tool, and not to stand or walk in front of, or next to tool when in
use.
5. Point out to all personnel the dangers related to the misuse of tool and the importance of following
safety procedures and instructions.
6. Do not make, or allow others to make, alterations or modifications to this tool.
Replace all lost or illegible labels.
7. Follow all safety, installation and maintenance instructions provided with this tool. Establish proper
safety procedures in accordance with local and national requirements to prevent accidental energizing
of tool that can cause injuries.
8. If this tool is sold or change in ownership takes place, you must provide the new owner all safety
instructions, notices and maintenance instructions you were originally provided. You can obtain
additional copies of the instructions from Kentmaster, free of charge upon request.
9. Give copies of instructions to: (A) Tool Operators
(B) Maintenance Supervisor
(C) Clean-up Supervisor

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 38 of 44

REV G: 8/5/08

GENERAL INFORMATION
___________________________________________________________________________________________
COVERING: SAFETY PRECAUTIONS AND PLACING INTO SERVICE

ELECTRICAL POWERED CARCASS SPLITTING SAW

___________________________________________________________________________________________

READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING

THIS TOOL
_____________________________________________________________________________________________________
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THIS INFORMATION INTO THE HANDS OF THE OPERATOR.
_____________________________________________________________________________________________________

PLACING INTO SERVICE

_____________________________________________________________________________________________________

! WARNING

! CAUTION

= Hazards or unsafe practices which could result in severe personal injury, death or
substantial property damage.
= Hazards or unsafe practices which could result in minor personal injury, product or
property damage.
= Important installation, operation or maintenance information.

! NOTICE

Installation, adjustment repair and maintenance of this tool must be made by trained
and qualified personnel.
! WARNING
! WARNING

Always disconnect power supply from tool before:

(A) Installing or removing blade from tool.
(B) Making repairs or adjustments to the tool.
(C) performing maintenance or cleanup work.

INSTALLATION INSTRUCTIONS

! WARNING

ALL ELECTRICAL WIRING MUST BE DONE BY A LICENSED ELECTRICIAN IN

ACCORDANCE WITH THE NATIONAL, STATE AND LOCAL ELECTRICAL CODES.
(REFER TO NAMEPLATE ON TOOL FOR PROPER POWER CONFIGURATION).

1. A BALANCER IS REQUIRED FOR OPERATION AND USE OF THIS TOOL. WEIGHT OF TOOL MUST FALL WITHIN
WEIGHT RANGE OF BALANCER. "AIR-BALANCERS" WHICH OPERATE ON COMPRESSED AIR, ARE HIGHLY
RECOMMENDED FOR USE WITH BANDMASTER SAWS. THEY PROVIDE LONG TRAVEL AND VERY SMOOTH,
UNIFORM RISE AND FALL. THEY CAN BE INTERFACED WITH THE OPERATION OF THE SAW.
2. INSTALL BALANCER ABOVE WORK AREA. BALANCER MUST HAVE SUFFICIENT VERTICAL TRAVEL SO
OPERATOR CAN REACH ENTIRE WORK AREA WITH TOOL WITHOUT STRAIN.
3. ADJUST BALANCER ACCORDING TO THE OPERATOR'S PREFERENCE AND COMFORT.
4. TOOL REQUIRES GREASING AFTER EVERY 40 HOURS OF OPERATION. GREASE USING KENTMASTER
GREASE (PART NO. 7903070).

! WARNING

WE STRONGLY SUGGEST THAT AN ADDITIONAL SAFETY CHAIN BE USED TO CHAIN

BALANCER TO OVERHEAD TROLLEY. THIS ADDITIONAL MEASURE OF SAFETY WILL
HELP REDUCE INJURIES.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 39 of 44

REV G: 8/5/08

OPERATING INSTRUCTIONS
ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.
! WARNING
1. HOLD TOOL FIRMLY AT BOTH TRIGGER HANDLES. SQUEEZE TRIGGERS SIMULTANEOUSLY TO ACTIVATE
TOOL.
2. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.
3. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.
4. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.
5. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP GUIDE SAW DOWN CENTER OF
BACKBONE AND UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE.
6. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT.
7. PUSH SAW FORWARD SO THAT GUARDS, ITEMS 1 AND 2, FIGURE 1, RIDE AGAINST BEEF. THIS HELPS STEADY
SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING.

MAINTENANCE
! WARNING

ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE

AND SERVICE TO THIS TOOL.

1. FOLLOW PROCEDURE NO. 4 OF INSTALLATION INSTRUCTIONS.

BLADE REMOVAL AND CLEANING.

! WARNING

ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR

REMOVING BLADE FROM TOOL.

ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADES FROM TOOL.
! WARNING
1. REMOVE PAPER WRAPPER FROM BLADE.
2. OPEN COVERS, FIGURE 1, ITEMS 3 AND 4.
3. INSTALL TORQUE WRENCH INTO SCREW, FIGURE 1, ITEM 5, AND TURN COUNTER-CLOCKWISE (CCW).
THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEM 7 AND 8, TO RETRACT.
4. SLIDE TAKE-UP WHEEL TO RIGHT.
5. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING AROUND
AND OVER THE TAKE-UP AND DRIVE WHEELS.
6. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL
AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER TENSION
ON BLADE).
7. TWIST BLADE 90 DEGREES AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING
DOWNWARD.
8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, ONE OR TWO TURNS TO CHECK TRACKING OF BLADE ON
WHEELS.
9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS.

SERVICE
1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN YOUR PREVENTIVE MAINTENANCE
PROGRAM.
2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.
3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE INFORMATION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 40 of 44

REV G: 8/5/08

DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE -DECLARACION DE CONFORMIDAD- ERKLARUNG BEZUGLICH EINHALTUNG DER VORSCHRIFTEN
DICHIARAZIONE DI CONFORMITA . CONFORMITEITSVERKLARING

MANUFACTURED BY:

KENTMASTER MFG CO., INC.

FABRIQUE PAR:
FABRICADA POR:
HERGESTELLTVON:
FABBRICATO DA:
VERVAARDIGD DOOR:

1801 SOUTH MOUNTAIN AVE.

MONROVIA, CALIFORNIA 91016
UNITED STATES OF AMERICA
TELEPHONE (626) 359-8888 FAX (626) 303-5151

TYPE / SERIES: CARCASS SPLITTING SAW

TYPE / SERIE:
TIPO / SERIE:
TYP / SERIE:
TIPO / SERIE:
TYPE / SERIE:

MODEL: BM-V-S, BM-V-SB, BM-V-SD AND BM-V-SDB

MODELE:
MODELO:
MODELL:
MODELLO:
MODEL:

SERIAL NO. RANGE: XXXXX

N SERIE: GAMA DE No. DE SERIE: SERIEN-NR.-BEREICH: NUMERI DI SERIE: SERIENUMMERS:

This product complies with the following European Community Directives:

Ce produit est conforme aux directives de la Communaute europeenne suivantes:
Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses Produkt erfullt die folgenden Vorschriften der Europaischen Gemeinschaft:
Questo prodotto e conforme alle seguenti direttive CEE:
Dit produkt voldoet aan de volgende EG-richtlijnen:

89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC

_______________________________________________________________________
The following Standards were used to verify compliance with the Directives:
Les normes suivantes ont ete utilisees pour verifier la conformite avec les Directives:
Las siguientes Normas se usaron para verificar el cumplimiento de las Directrices:
Folgende Normen wurden angewandt, um erfullung der vorschriften zu bestatigen:
Per verificare la conformita del prodotto alle direttive sono stati usati i seguenti standard:
De volgende normen zijn gebruikt om naleving van de richtlijnen te bevestigen:

EN 292
_______________________________________________________________________________________________________

Approved by: ________________________

Date: AUG - 1 - 1995

RALPH KARUBIAN MONROVIA, CA. U.S.A

(Engineering Manager)

(Directeur technique) (gerente de ingenieria) (verantwortlicher Konstruktionsleiter) (Responsabile tecnico) (ondersteunend technisch mangar)

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 41 of 44

REV G: 8/5/08

Kentmaster Worldwide Location

Kentmaster Equipment (Aust) PTY.LTD.

Kentmaster South Africa (PTY) LTD.

Unit 2,24 Central Court

Johannesburg - S. Africa
Unit 54 Sunnyrock Park
Sunrock Close, Germiston
South Africa

Browns Plains Qld. 4118

Australia
Telephone: (07) 3806-8400
Fax: (07) 3806-7933
Australia@Kentmaster.com
Kentmaster do Brasil, Ltda.
Av. Dr. Joao Teodoro No. 805
Bairro De Vila Rezende
13405-240 Piracicaba, SP,
Brazil
Telephone #1: (019) 3 413 3113
Telephone #2: (019)983-4973
Fax: (019) 3 413 3113
Brazil@Kentmaster.com
Kentmaster (IRL) LTD.
Benamore, Dublin Road.
Roscrea,
CO, Tipperary,
Ireland
Telephone: (353) 0505-23292
Fax: (353) 0505-23299
Ireland@Kentmaster.com
Kentmaster Equipment (NZ) LTD.
5 Cooper Street
Havelock North
New Zealand
Telephone #1: (64) 6 8777 857
Telephone #2: 0800 KENTMASTER
Fax: (64) 6 8777 858
NewZealand@Kentmaster.com

Telephone: (27) 11-455-3748

Fax: (27) 11-455-3749
SouthAfrica@Kentmaster.com
Kentmaster (UK ) LTD.
Unit 16 Avonbank Ind. Centre
West Town Rd, Avonmouth-Bristol,
BS11 9DE
England
Telephone: (44) 117-923-5035
Fax: (44)-117-932-9010
UK@Kentmaster.com
Kentmaster Mfg. Co., Inc.
1801 South Mountain Ave.
Monrovia, CA, 91016
USA
Telephone #1: (626) 359-8888
Telephone #2: (800) 421-1477
Fax: (626) 303-5151
info@Kentmaster.com
Kentmaster Omaha
4417 South 139th Street
Omaha, NE, 68137
USA
Telephone #1: (402) 896-3355
Telephone #2: (800) 367-3181
Fax: (402) 896-3311
Omaha@Kentmaster.com

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 42 of 44

REV G: 8/5/08

INDEX
OPERATING AND SAFETY INSTRUCTIONS................................................................................................................................... 2
OPERATING INSTRUCTIONS...................................................................................................................................................... 3
MAINTENANCE............................................................................................................................................................................... 3
CLEANING AND STERILIZING SAW......................................................................................................................................... 4
WATER CONNECTION.................................................................................................................................................................. 4
TORQUE WRENCH CALIBRATION ........................................................................................................................................... 4
HANGER............................................................................................................................................................................................ 5
TROUBLE SHOOTING HINTS: .......................................................................................................................................................... 6
SERVICE ................................................................................................................................................................................................ 7
PARTS BOOK......................................................................................................................................................................................... 7
MODELS MAIN ASSEMBLIES...................................................................................................................................................... 7
TAKE-UP SIDE ASSEMBLY ........................................................................................................................................................ 14
DRIVE SIDE ASSEMBLY ............................................................................................................................................................. 16
BLADE GUIDE ASSEMBLY, TAKE-UP SIDE .......................................................................................................................... 19
BLADE GUIDE ASSEMBLY, DRIVE SIDE................................................................................................................................ 21
HANDLES ........................................................................................................................................................................................ 22
ADDITIONAL SPRAY OPTIONS ................................................................................................................................................ 23
MOTOR ASSEMBLY..................................................................................................................................................................... 24
POWER SUPPLY OPTIONS......................................................................................................................................................... 27
WIRING DIAGRAMS .......................................................................................................................................................................... 30
GENERAL INFORMATION ............................................................................................................................................................... 39
INSTALLATION INSTRUCTIONS ............................................................................................................................................. 39
OPERATING INSTRUCTIONS.................................................................................................................................................... 40
MAINTENANCE............................................................................................................................................................................. 40
SERVICE.......................................................................................................................................................................................... 40
DECLARATION OF CONFORMITY ................................................................................................................................................. 41
Kentmaster Worldwide Location .......................................................................................................................................................... 42
INDEX................................................................................................................................................................................................... 43
FIGURES - INDEX.............................................................................................................................................................................. 44

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 43 of 44

REV G: 8/5/08

FIGURES - INDEX
Figure 1 BM-V- ....................................................................................................................................................................................... 5
Figure 2 MODELS BM-V-SDB AND BM-V-SD................................................................................................................................... 8
Figure 3 BOM FOR MODELS BM-V-SDB AND BM-V-SD................................................................................................................ 9
Figure 4 MODEL BM-V-S.................................................................................................................................................................... 10
Figure 5 BOM FOR MODEL BM-V-S ................................................................................................................................................. 11
Figure 6 MODEL BM-V-SB ................................................................................................................................................................. 12
Figure 7 BOM FOR MODEL BM-V-SB .............................................................................................................................................. 13
Figure 8 TAKE-UP SIDE ASSEMBLY................................................................................................................................................ 14
Figure 9 TAKE-UP SIDE ASSEMBLY BOM...................................................................................................................................... 15
Figure 10 DRIVE SIDE ASSEMBLY................................................................................................................................................... 16
Figure 11 DRIVE SIDE ASSEMBLY BOM......................................................................................................................................... 18
Figure 12 TRANSMISSION OVERVIEW ........................................................................................................................................... 18
Figure 13 BLADE GUIDE ASSEMBLY, FRONT (BM-V-S & SB) ................................................................................................... 19
Figure 14 BLADE GUIDE ASSEMBLY, FRONT (BM-V-SDB & SD).............................................................................................. 20
Figure 15 BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-S, SB, SD, SDB)............................................................................. 21
Figure 16 TOP HANDLE ASSEMBLY................................................................................................................................................ 22
Figure 17 REAR HANDLE ASSEMBLY............................................................................................................................................. 22
Figure 18 SPRAY TUBE UNDER BEAM ASSEMBLY ..................................................................................................................... 23
Figure 19 1710897: EXTERNAL SPRAY NOZZLE ........................................................................................................................... 23
Figure 20 2HP MOTOR OPTIONS....................................................................................................................................................... 24
Figure 21 3HP MOTOR OPTIONS....................................................................................................................................................... 25
Figure 22 5HP MOTOR OPTIONS....................................................................................................................................................... 26
Figure 23 POWER SUPPLY, 42V, with ANTI-TIEDOWN................................................................................................................. 27
Figure 24 POWER SUPPLY, 42V, without ANTI-TIEDOWN............................................................................................................ 27
Figure 25 POWER SUPPLY, NON 42V, with ANTI-TIEDOWN ....................................................................................................... 28
Figure 26 POWER SUPPLY, NON 42V, without ANTI-TIEDOWN.................................................................................................. 28
Figure 28 POWER SUPPLY, SINGLE PHASE, 115 / 230V ............................................................................................................... 29
Figure 29 WIRING DIAGRAM SINGLE PHASE 230V ............................................................................................................... 30
Figure 30 WIRING DIAGRAM SINGLE PHASE 115V ............................................................................................................... 31
Figure 31 WIRING DIAGRAM 3 PHASE DIFFERENT CONTROL AND MOTOR VOLTAGE without Anti-Tie Down...... 32
Figure 32 WIRING DIAGRAM 3 PHASE SAME CONTROL AND MOTOR VOLTAGE without Anti-Tie Down ................ 33
Figure 33 WIRING DIAGRAM 3 PHASE DIFFERENT CONTROL AND MOTOR VOLTAGE with Anti-Tie Down........... 34
Figure 34 WIRING DIAGRAM 3 PHASE SAME CONTROL/TRIGGER AND MOTOR VOLTAGE with Anti-Tie Down.... 35
Figure 35 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR ........................................................................... 36

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
 TELEPHONE: (818) 359-8888 FAX: (818) 303-5151

Page 44 of 44