Modeling and Simulation of PV Array With Boost Converter: An Open Loop Study
Modeling and Simulation of PV Array With Boost Converter: An Open Loop Study
A THESIS IN PARTIAL FULFILMENTS OF REQUIREMENTS FOR THE AWARD OF THE DEGREE OF Bachelor of Technology
BY
DEPARTMENT OF ELECTRICAL ENGINEERING NATIONAL INSTITUTE OF TECHNOLOGY ROURKELA 769008 INDIA 2011
MODELING AND SIMULATION OF PV ARRAY WITH BOOST CONVERTER: AN OPEN LOOP STUDY
A THESIS IN PARTIAL FULFILMENTS OF REQUIREMENTS FOR THE AWARD OF THE DEGREE OF Bachelor of Technology
DEPARTMENT OF ELECTRICAL ENGINEERING NATIONAL INSTITUTE OF TECHNOLOGY ROURKELA 769008 INDIA 2011
ii
CERTIFICATE
This is to certify that the thesis entitled Modeling and simulation of PV array with boost converter : An open loop study submitted by Debashis Das (107EE024) and Shishir Kumar Pradhan (107EE039) in the partial fulfillment of the requirements for the award of Bachelor of Technology degree in Electrical Engineering at National Institute of Technology, Rourkela is an authentic work carried out by them under my supervision and guidance. To the best of my knowledge, the matter embodied in the thesis has not been submitted to any other University/Institute for the award of any Degree or Diploma.
Date:
ACKNOWLEDGEMENT
We wish to express our deep sense of gratitude and indebtedness to Prof. SOMNATH MAITY, Department of Electrical Engineering, N.I.T Rourkela, for introducing the present topic and for their inspiring guidance, constructive criticism and valuable suggestion throughout this project work. Our sincere thanks to all our friends who have patiently extended all sorts of help for accomplishing this undertaking.
Date:
Place:
SHISHIR KUMAR PRADHAN (107EE039) Department of Electrical Engineering National Institute of Technology Rourkela - 769008
iv
CONTENTS
CHAPTER
TITLE
PAGE
PRELIMINARIES
2.1 2.2 2.3 2.4 2.5 2.6 Renewable energy Solar energy Distribution of solar radiation Solar radiation reaching earth surface Spectrum of sun Standard test conditions (STC)
4-9
5 5 6 7 8 9
PHOTOVOLTAIC SYSTEMS
3.1 3.2 Definition Photovoltaic arrangements 3.2.1 Photovoltaic cell 3.2.2 Photovoltaic module 3.2.3 Photovoltaic array Materials used in PV cells
v
10-21
11 11 11 12 12 13
3.3
3.4 3.5
Characteristics of PV cells 3.4.1 Efficiency of PV cell Modelling of PV array 3.5.1 PV array characteristic curves 3.5.2 MATLAB code for PV array
14 15 16 17 20
CONVERTERS
4.1 4.2 DC-DC Converters Boost converter and its operation 4.2.1 Steady state analysis of the boost converter 4.2.2 Design of the boost converter Interfacing of the PV array with boost converter
22-30
23 23 24 26 28
4.3
31-42
32 33 37 38 40 41
CONCLUSIONS REFERENCES
43 45
vi
LIST OF TABLES
TABLE NO.
1. 2.
TITLE
Parameters value used in MATLAB code Value of input voltage and current for variation in load resistance for an irradiance level (100 mW/m2) Value of input voltage and current for variation in load resistance for an irradiance level (80 mW/m2)
PAGE NO.
32 41
3.
42
vii
LIST OF FIGURES
FIGURE NO.
2.1 2.2 3.1 3.2 3.3 3.4 3.5 3.6 Solar radiation distribution Spectral distribution of black body radiation and solar radiation Basic structure of PV cell Photovoltaic system Equivalent circuit of a PV cell Equivalent circuit of a PV array I-V and P-V characteristics I-V characteristic of a solar array for a fixed temperature but varying irradiance 3.7 P-V characteristic of a solar array for a fixed temperature but varying irradiance 3.8 I-V Characteristic of a PV array under a fixed irradiance but varying temperatures 3.9 P-V Characteristic of a PV array under a fixed irradiance but varying temperatures 4.1 4.2 4.3 4.4 4.5 4.6 Circuit diagram of a boost converter The OFF state diagram of the boost converter The ON state diagram of the boost converter Inductor current waveform Inductor voltage waveform The complete simulink circuit model showing the coupling of PV array with the boost converter. 4.7 4.8 5.1 5.2 PV panel block diagram. Detailed internal circuit diagram of PV array in simulink I-V curves obtained at 280C for various irradiance levels P-V curves obtained at 280C for various irradiance levels 29 29 33 34 23 24 24 25 25 28 19 19 18
TITLE
PAGE NO.
6 8 11 12 14 16 17 18
viii
5.3 5.4
P-I curves obtained at 280C for various irradiance levels I-V curves obtained at an irradiance of 100 mW /cm2 for various temperatures P-I curves obtained at an irradiance of 100 mW/cm2 for various temperatures. P-V curves obtained at an irradiance of 100 mW/cm2 various temperatures.
34 35
5.5
35
5.6
36
The complete simulation model of the PV energy conversion system. Circuit diagram for PWM signal generation Simulation diagram showing the generation of the PWM signal PWM signal generated The current output of the system The voltage output of the system Interfacing of PV array simulation result with open loop I-V characteristic
37 38 38 39 40 40 42
ix
Page |1
ABSTRACT
The recent upsurge in the demand of PV systems is due to the fact that they produce electric power without hampering the environment by directly converting the solar radiation into electric power. However the solar radiation never remains constant. It keeps on varying throughout the day. The need of the hour is to deliver a constant voltage to the grid irrespective of the variation in temperatures and solar insolation. We have designed a circuit such that it delivers constant and stepped up dc voltage to the load. We have studied the open loop characteristics of the PV array with variation in temperature and irradiation levels. Then we coupled the PV array with the boost converter in such a way that with variation in load, the varying input current and voltage to the converter follows the open circuit characteristic of the PV array closely. At various insolation levels, the load is varied and the corresponding variation in the input voltage and current to the boost converter is noted. It is noted that the changing input voltage and current follows the open circuit characteristics of the PV array closely.
Chapter
INTRODUCTION
Page |3
1.1
MOTIVATION
The Conventional sources of energy are rapidly depleting. Moreover the cost of energy is
rising and therefore photovoltaic system is a promising alternative. They are abundant, pollution free, distributed throughout the earth and recyclable. The hindrance factor is its high installation cost and low conversion efficiency. Therefore our aim is to increase the efficiency and power output of the system. It is also required that constant voltage be supplied to the load irrespective of the variation in solar irradiance and temperature. PV arrays consist of parallel and series combination of PV cells that are used to generate electrical power depending upon the atmospheric conditions (e.g solar irradiation and temperature). So it is necessary to couple the PV array with a boost converter. Moreover our system is designed in such a way that with variation in load, the change in input voltage and power fed into the converter follows the open circuit characteristics of the PV array. Our system can be used to supply constant stepped up voltage to dc loads.
1.2
WORK SUMMARY
We have discussed about the renewable energy, solar energy, distribution of solar
radiation reaching the earths surface and spectrum of sun in chapter 2. The details regarding the PV cell have been discussed in chapter 3. The PV array has been designed in MATLAB environment. The open-circuit characteristic of the PV cell has been studied in depth. The boost converter design, the coupling of the PV array with the converter has been described in chapter 4. The chapter 5 deals with the simulation results and discussions part. The P-V, I-V, P-I curves have been obtained at varying irradiation levels and temperatures. The generation of the PWM signal has been shown. We get constant voltage across the load resistance of the boost converter. Output load of the boost converter is varied and the variation in the input voltage and current fed into the boost converter is noted. The various values of the voltage and current have been plotted in the open loop curves of the PV array. The voltage and current values lie on the curves and thereby prove that our coupling of the boost converter with the PV array is proper.
Chapter
PRELIMINARIES
P age |5
2.1
RENEWABLE ENERGY
Renewable energy sources also called non-conventional type of energy are the sources
which are continuously replenished by natural processes. Such as, solar energy,
bio-energy -
bio-fuels grown sustainably, wind energy and hydropower etc., are some of the examples of renewable energy sources. A renewable energy system convert the energy found in sunlight, falling-water, wind, sea-waves, geothermal heat, or biomass into a form, which we can use in the form of heat or electricity. The majority of the renewable energy comes either directly or indirectly from sun and wind and can never be fatigued, and therefore they are called renewable [12]. However, the majority of the world's energy sources came from conventional sourcesfossil fuels such as coal, natural gases and oil. These fuels are often term non-renewable energy sources. Though, the available amount of these fuels are extremely large, but due to decrease in level of fossil fuel and oil level day by day after a few years it will end. Hence renewable energy source demand increases as it is environmental friendly and pollution free which reduces the greenhouse effect [12].
2.2
SOLAR ENERGY
Solar energy is a non-conventional type of energy. Solar energy has been harnessed by
humans since ancient times using a variety of technologies. Solar radiation, along with secondary solar-powered resources such as wave and wind power, hydroelectricity and biomass, account for most of the available non-conventional type of energy on earth. Only a small fraction of the available solar energy is used [13]. Solar powered electrical generation relies on photovoltaic system and heat engines. Solar energy's uses are limited only by human creativity. To harvest the solar energy, the most common way is to use photo voltaic panels which will receive photon energy from sun and convert to electrical energy. Solar technologies are broadly classified as either passive solar or active solar depending on the way they detain, convert and distribute solar energy.
P age |6
Active solar techniques include the use of PV panels and solar thermal collectors to strap up the energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light dispersing properties and design spaces that naturally circulate air [5].Solar energy has a vast area of application such as electricity generation for distribution, heating water, lightening building, crop drying etc.
2.3
From the above Figure 2.1 of solar radiation, Earth receives 174 petawatts (PW) of incoming solar radiation at the upper atmosphere. Approximately 30% is reflected back to space and only 89 pw is absorbed by oceans and land masses. The spectrum of solar light at the Earth's surface is generally spread across the visible and near-infrared reason with a small part in the near-ultraviolet. The total solar energy absorbed by Earth's atmosphere, oceans and land masses is approximately 3,850,000 EJ per year [13].
P age |7
2.4
meter is known as Solar Constant. It is important to realize that it is not the intensity per square meter of the Earths surface but per square meter on a sphere with the radius of 149,596,000 km and with the Sun at its centre. The total amount solar radiation intercepted by the Earth is the Solar Constant multiplied by the cross section area of the Earth. If we now divide the calculated number by the surface area of the Earth, we shall find how much solar radiation is received in an average per square meter of the Earth's surface [10]. Hence the average solar radiation R per square meter of the Earth surface is,
The Handy formula which is used to calculate solar energy received by earth E=3.6* where E is the solar energy in EJ. S is the Solar Constant in W/m2. n is the number of hours. r is the Earth's radius in km [10]. )*S*n*
P age |8
2.5
SPECTRUM OF SUN
The performance of Photovoltaic device is reliant on the spectral distribution of solar
radiation. The standard spectral distribution is mainly used as reference for evaluation of PV devices. There are two standard terrestrial distribution defined by the American Society for Testing and Materials (ASTM), global AM1.5 and direct normal. The solar radiation that is perpendicular to a plane directly facing the sun is known as direct normal. The global corresponds to the spectrum of the diffuse radiations. Diffuse radiations are the radiations which are reflected on earths surface or influenced by atmospheric conditions. To measure the global radiations an instrument named pyranometer is used. This instrument is designed in such a way that it responds to each wavelengths and so that we get a precise value for total power in any incident spectrum [5].
Figure 2.2 Spectral distribution of black body radiation and sun radiation [11]. The AM initials in the above Figure stands for air mass. The air mass in this circumstance means the mass of air between a surface and the sun [6]. The length of the path of solar radiation from the sun through the atmosphere is indicated by the number AMx. The longer the path the more is the deviation of light. The AM0 in the above figure means the spectral distribution and intensity of sunlight in near-earth space without atmospheric attenuation [6].
P age |9
2.6
performance and characteristic curve. The parameters are always given in datasheet. The datasheet make available the notable parameter regarding the characteristics and performance of PV cells with respect to standard test condition. Standard test conditions are as follows: Temperature (Tn) = 250c Irradiance (Gn) = 1000 Spectrum of x = 1.5 i.e. AM.
Chapter
PHOTOVOLTAIC SYSTEMS
P a g e | 11
3.1
DEFINITION
A photovoltaic system is a system which uses one or more solar panels to convert solar
energy into electricity. It consists of multiple components, including the photovoltaic modules, mechanical and electrical connections and mountings and means of regulating and/or modifying the electrical output [14].
3.2
PHOTOVOLTAIC ARRANGEMENTS
3.2.1 PHOTOVOLTAIC CELL PV cells are made of semiconductor materials, such as silicon. For solar cells, a thin semiconductor wafer is specially treated to form an electric field, positive on one side and negative on the other. When light energy strikes the solar cell, electrons are knocked loose from the atoms in the semiconductor material. If electrical conductors are attached to the positive and negative sides, forming an electrical circuit, the electrons can be captured in the form of an electric current - that is, electricity. This electricity can then be used to power a load[16]. A PV cell can either be circular or square in construction.
P a g e | 12
3.2.2 PHOTOVOLTAIC MODULE Due to the low voltage generated in a PV cell (around 0.5V), several PV cells are connected in series (for high voltage) and in parallel(for high current) to form a PV module for desired output. Separate diodes may be needed to avoid reverse currents, in case of partial or total shading, and at night. The p-n junctions of mono-crystalline silicon cells may have adequate reverse current characteristics and these are not necessary. Reverse currents waste power and can also lead to overheating of shaded cells. Solar cells become less efficient at higher temperatures and installers try to provide good ventilation behind solar panels [15].
3.2.3 PHOTOVOLTAIC ARRAY The power that one module can produce is not sufficient to meet the requirements of home or business. Most PV arrays use an inverter to convert the DC power into alternating current that can power the motors, loads, lights etc. The modules in a PV array are usually first connected in series to obtain the desired voltages; the individual modules are then connected in parallel to allow the system to produce more current [14].
P a g e | 13
3.3
The materials used in PV cells are as follows: Single-crystal silicon Single-crystal silicon cells are the most common in the PV industry. The main technique for producing single-crystal silicon is the Czochralski (CZ) method. High-purity polycrystalline is melted in a quartz crucible. A single-crystal silicon seed is dipped into this molten mass of polycrystalline. As the seed is pulled slowly from the melt, a single-crystal ingot is formed. The ingots are then sawed into thin wafers about 200-400 micrometers thick (1 micrometer = 1/1,000,000 meter). The thin wafers are then polished, doped, coated, interconnected and assembled into modules and arrays [7].
Polycrystalline silicon Consisting of small grains of single-crystal silicon, polycrystalline PV cells are less energy efficient than single-crystalline silicon PV cells. The grain boundaries in polycrystalline silicon hinder the flow of electrons and reduce the power output of the cell. A common approach to produce polycrystalline silicon PV cells is to slice thin wafers from blocks of cast polycrystalline silicon. Another more advanced approach is the ribbon growth method in which silicon is grown directly as thin ribbons or sheets with the approach thickness for making PV cells [7]. Gallium Arsenide (GaAs) A compound semiconductor made of two elements: Gallium (Ga) and Arsenic (As). GaAs has a crystal structure similar to that of silicon. An advantage of GaAs is that it has high level of light absorptivity. To absorb the same amount of sunlight, GaAs requires only a layer of few micrometers thick while crystalline silicon requires a wafer of about 200-300 micrometers thick. Also, GaAs has much higher energy conversion efficiency than crystal silicon, reaching about 25 to 30%.The only drawback of GaAs PV cells is the high cost of single crystal substrate that GaAs is grown on [7]. Cadmium Telluride (CdTe) It is a polycrystalline compound made of cadmium and telluride with a high light absorbility capacity (i.e a small thin layer of the compound can absorb 90% of solar irradiation).The main
P a g e | 14
disadvantage of this compound is that the instability of PV cell or module performance. As it a toxic substance, the manufacturing process should be done by extra precaution [7]. Copper Indium Diselenide (CuInSe2) It is a polycrystalline compound semiconductor made of copper, indium and selenium. It delivers high energy conversion efficiency without suffering from outdoor degradation problem. It is one of the most light-absorbent semiconductors. As it is a complex material and toxic in nature so the manufacturing process face some problem [7].
3.4
CHARACTERISTICS OF PV CELL
Figure 3.3 Equivalent circuit of a PV cell An ideal is modeled by a current source in parallel with a diode. However no solar cell is ideal and thereby shunt and series resistances are added to the model as shown in the PV cell diagram above. RS is the intrinsic series resistance whose value is very small. RP is the equivalent shunt resistance which has a very high value [4]. Applying Kirchoffs law to the node where Iph, diode, Rp and Rs meet, we get Iph=ID+IRp+I We get the following equation for the photovoltaic current: I= Iph-IRp-ID I = Iph Io.* ( ) +-[ ] (3.2) (3.3) (3.1)
P a g e | 15
Where,
Iph is the Insolation current, I is the Cell current, I0 is the Reverse saturation
current, V is the Cell voltage, Rs is the Series resistance, Rp is the Parallel resistance, VT is the Thermal voltage ( ), K is the Boltzman constant, T is the Temperature in Kelvin, q is the Charge of an electron.
3.4.1 EFFICIENCY OF PV CELL The efficiency of a PV cell is defined as the ratio of peak power to input solar power. = (3.4)
where, Vmp is the voltage at peak power, Imp is the current at peak power, I is the solar intensity per square metre, A is the area on which solar radiation fall. The efficiency will be maximum if we track the maximum power from the PV system at different environmental condition such as solar irradiance and temperature by using different methods for maximum power point tracking.
P a g e | 16
3.5
MODELLING OF PV ARRAY:
The building block of PV arrays is the solar cell, which is basically a p-n junction that
directly converts light energy into electricity: it has a equivalent circuit as shown below in Figure 3.4.
Figure 3.4 Equivalent circuit of a PV cell The current source Iph represents the cell photo current; Rj is used to represent the non-linear impedence of the p-n junction; Rsh and Rs are used to represent the intrinsic series and shunt resistance of the cell respectively. Usually the value of Rsh is very large and that of Rs is very small,hence they may be neglected to simplify the analysis. PV cells are grouped in larger units called PV modules which are further interconnected in series-parallel configuration to form PV arrays or PV generators[3].The PV mathematical model used to simplify our PV array is represented by the equation: I=npIph-npIrs[exp( * ) -1] (3.5)
where I is the PV array output current; V is the PV array output voltage; ns is the number of cells in series and np is the number of cells in parallel; q is the charge of an electron; k is the Boltzmanns constant; A is the p-n junction ideality factor; T is the cell temperature (K); Irs is the cell reverse saturation current. The factor A in equation (3.5) determines the cell deviation from the ideal p-n junction characteristics; it ranges between 1-5 but for our case A=2.46 [3]. The cell reverse saturation current Irs varies with temperature according to the following equation: Irs=Irr[ ]3exp( [ - ]) (3.6)
P a g e | 17
Where Tr is the cell reference temperature, Irr is the cell reverse saturation temperature at Tr and EG is the band gap of the semiconductor used in the cell. The temperature dependence of the energy gap of the semi conductor is given by [20]: EG= EG(0)(3.7)
The photo current Iph depends on the solar radiation and cell temperature as follows: Iph=[ Iscr + Ki(T Tr)] (3.8)
where Iscr is the cell short-circuit current at reference temperature and radiation, Ki is the short circuit current temperature coefficient, and S is the solar radiation in mW/cm2. The PV power can be calculated using equation (3.5) as follows: P=IV= npIphV[( * )-1] (3.9)
3.5.1 PV ARRAY CHARACTERISTIC CURVES The current to voltage characteristic of a solar array is non-linear, which makes it difficult to determine the MPP. The Figure below gives the characteristic I-V and P-V curve for fixed level of solar irradiation and temperature.
P a g e | 18
The IV and PV curves for various irradiance but a fixed temperature (250C) is shown below in Figure (3.6)& (3.7).The characteristic I-V curve tells that there are two regions in the curve: one is the current source region and another is the voltage source region. In the voltage source region (in the right side of the curve), the internal impedance is low and in the current source region (in the left side of the curve),the impedance is high. Irradiance temperature plays an important role in predicting the I-V characteristic, and effects of both factors have to be considered while designing the PV system. Whereas the irradiance affects the output, temperature mainly affects the terminal voltage. The figures (3.8), (3.9) gives the simulated I-V and P-V characteristic for various temperatures at a fixed irradiance at 1000 W/m2 [4].
Figure 3.6 I-V characteristic of a solar array for a fixed temperature but varying irradiance
Figure 3.7 P-V characteristic of a solar array for a fixed temperature but varying irradiance
P a g e | 19
Figure 3.8 I-V Characteristic of a PV array under a fixed irradiance but varying temperatures
Figure 3.9 P-V Characteristic of a PV array under a fixed irradiance but varying temperatures. From the I-V, we observe that the short circuit current increases with increase in irradiance at a fixed temperature. Moreover, from the I-V and P-V curves at a fixed irradiance, it is observed that the open circuit voltage decreases with increase in temperature.
P a g e | 20
T=28+273; Tr1=40; % Reference temperature in degree fahrenheit % % Reference temperature in kelvin Solar radiation in mW/sq.cm
Eg=Eg0-(alpha*T*T)/(T+beta)*q; semiconductor used cell in joules Np=4; Ns=60; V0=[0:1:300]; for i=1:5 Iph=(Iscr+ki*(T-Tr))*((S(i))/100);
band
gap
energy
of
Irs=Irr*((T/Tr)^3)*exp(q*Eg/(k*A)*((1/Tr)-(1/T))); I0=Np*Iph-Np*Irs*(exp(q/(k*T*A)*V0./Ns)-1); P0 = V0.*I0; figure(1) plot(V0,I0); axis([0 50 0 20]); xlabel('Voltage in volt'); ylabel('Current in amp'); hold on;
P a g e | 21 figure(2) plot(V0,P0); axis([0 50 0 400]); xlabel('Voltage in volt'); ylabel('Power in watt'); hold on; figure(3) plot(I0,P0); axis([0 20 0 400]); xlabel('Current in amp'); ylabel('Power in watt'); hold on; end
Chapter
CONVERTERS
P a g e | 23
4.1
DC-DC CONVERTERS
DC-DC converters can be used as switching mode regulators to convert an unregulated
dc voltage to a regulated dc output voltage. The regulation is normally achieved by PWM at a fixed frequency and the switching device is generally BJT, MOSFET or IGBT. The minimum oscillator frequency should be about 100 times longer than the transistor switching time to maximize efficiency. This limitation is due to the switching loss in the transistor. The transistor switching loss increases with the switching frequency and thereby, the efficiency decreases. The core loss of the inductors limits the high frequency operation. Control voltage Vc is obtained by comparing the output voltage with its desired value. Then the output voltage can be compared with its desired value to obtain the contol voltage Vcr. The PWM control signal for the dc converter is generated by comparing Vcr with a sawtooth voltage Vr.[8]. There are four topologies for the switching regulators: buck converter, boost converter, buck-boost converter, ck converter. However my project work deals with the boost regulator and further discussions will be concentrated towards this one.
4.2
voltage source Vg, boost inductor L, controlled switch S, diode D, filter capacitor C, and the load resistance R. When the switch S is in the on state, the current in the boost inductor increases linearly and the diode D is off at that time. When the switch S is turned off, the energy stored in the inductor is released through the diode to the output RC circuit[8].
P a g e | 24
(a) OFF STATE: In the OFF state, the circuit becomes as shown in the Figure (4.2) below [9].
When the switch is off, the sum total of inductor voltage and input voltage appear as the load voltage.
(b) ON STATE: In the ON state, the circuit diagram is as shown below in Figure (4.3):
When the switch is ON, the inductor is charged from the input voltage source Vg and the capacitor discharges across the load. The duty cycle, D= where T=
P a g e | 25
From the inductor voltage balance equation, we have:Vg(DTs) +(Vs-Vo)(1-D)Ts=0 Vg(DTs)-Vg(DTs)-VgTs+VoDTs-VoTs=0 Vo=Vg/(1-D) Conversion ratio, M=Vo/Vg=1/(1-D) From inductor current ripple analysis, change in inductor current, Il=(Imax-Imin) IL=(Vg/L)*(DTs) IL = (VgD)/(fsL) L=VgD/fs( IL) The boost converter operates in CCM (continuous conducting mode) for L> Lb where (4.2) (4.1)
Lb=
(4.3)
The current supplied to the output RC circuit is discontinuous. Thus a large filter capacitor is used to limit the output voltage ripple. The filter capacitor must provide the output dc current to the load when the diode D is off.
P a g e | 26
The minimum value of the filter capacitance that results in the voltage ripple Vr[8] is given by:
Cmin=
(4.4)
(1) CURRENT RIPPLE FACTOR (CRF): According to IEC harmonics standard, CRP should be bounded within 30%. i.e
= 30%
(4.5)
= 5%
(4.6)
GIVEN DATA: Input voltage, Vg=25V Output voltage, Vo=300V Output load current, Io=1A
P a g e | 27
(4.8)
IL= 1 A
=(0.3 * 1)A=0.3 A
(4.9)
L=(
(4.10)
= 300/1= 300.
C=D/f * R0 *( V0/V)= (.9166)/(10^5)*(300)*(.05)= .611 F. The transfer function of the boost converter[12] used for the modeling is given by:
G(s) =
(4.14)
Putting the values of R, L, C, D, Vg in the above equation, the transfer equation that results is given by:
G(s ) =
(4.15)
By trial and error, we get the value of KP which gives desired results as 6.03.
P a g e | 28
The PV array has been interfaced with the boost converter using a controlled voltage source as shown in the circuit diagram below:
Figure 4.6 The complete simulink circuit model showing the coupling of PV array with the boost converter
P a g e | 29
The PV array has been designed taken into consideration its dependence upon the irradiance, temperature, number of PV cells connected in series and parallel as explained in chapter 2[4]. The detailed internal circuit of the PV array showing the design is given below:
P a g e | 30
The M-file for Irs function has been developed using the equation (3.6) and that for the Iph function using equation (3.8). The PV array has been modeled using the equations (3.1) (3.9). The interfacing of the PV array with the boost converter has been achieved using a voltage controlled source. The inductor current which is same as the load current of the PV system is used as feedback for designing the PV array.
Chapter
P a g e | 32
5.1
The values of the parameters used in developing the MATLAB code for the Photovoltaic array have been tabled below[1], [20]:
PARAMETERS
Np Ns Iscr Tr1 Ki Irr K q A Eg0
VALUES 4 60 3.75 A 40 0C 0.00023 A/K 0.000021 A 1.38065 * 10-23 J/0K 1.6022* 10-19 C 2.15 1.66 eV 4.73* 10^-4 eV/K 636 K
P a g e | 33
5.2
The waveforms obtained by varying the solar insolation and temperatures which are fed into the PV array model have been plotted as shown below:
Figure 5.1 I-V curves obtained at 280C for various irradiance levels From Figure(5.1), we observed that by increasing the solar radiation at constant temperature the voltage and current output from PV array also increases.Hence at higher insolation we can get our required level voltage.
P a g e | 34
Figure 5.2 P-V curves obtained at 280C for various irradiance levels From Figure (5.2), we observed that by increasing the solar insolation level, the power output from PV array increases.
Figure 5.3 P-I curves obtained at 280C for various irradiance levels From figure (5.3), we observed that by increasing the solar radiation level, the current and power output from PV array increases.
P a g e | 35
Figure 5.4 I-V curves obtained at an irradiance of 100 mW /cm2 for various temperatures. From figure(5.4), we observed that by increasing the temperature level at constant irradiance, the voltage output from PV array decreases but current output increases slightly with respect to voltage and, hence the power output from PV array decreases.
Figure 5.5 P-I curves obtained at an irradiance of 100 mW/cm2 for various temperatures.
P a g e | 36
Figure 5.6 P-V curves obtained at an irradiance of 100 mW/cm2 various temperatures.
P a g e | 37
5.3
SIMULINK MODEL
The Figure (5.7) below shows the block diagram of the complete circuit. This includes the PV module, boost converter and control circuit. The modeling and simulation of the whole system has been done in MATLAB-SIMULINK environment.
Figure 5.7 The complete simulation model of the PV energy conversion system.
P a g e | 38
5.4
The simulink model for the generation of the PWM signal is shown below:
Figure 5.8 Circuit diagram for PWM signal generation The output of the filter which is the control signal is compared with the saw-tooth waveform having a peak voltage of 25V to generate the PWM signal which is fed as gate signal to the MOSFET. The simulation diagram showing the comparison of the saw-tooth waveform with the control signal is shown below:
Figure 5.9 Simulation diagram showing the generation of the PWM signal
P a g e | 39
The required PWM signal used as the gate pulse for the MOSFET is shown below in the figure:
P a g e | 40
5.5
SIMULATION RESULTS
The output Iout and Vout curves obtained across the load resistance of the boost converter of the simulink model as shown in above Figure(5.11) is drawn below.
Figure 5.12 The voltage output across the load resistance of the boost converter
P a g e | 41
5.6
Table 2: Value of input voltage and current for variation in load resistance for an irradiance level (100 mW/m2) LOAD RESISTANCE() INPUT VOLTAGE(Volt) INPUT CURRENT(Amp)
INSOLATION(mW/m2)
100
300
28.92
11.42
100
285
27.2
12.86
100
450
31.62
6.898
P a g e | 42
Table 3: Value of input voltage and current for variation in load resistance for an irradiance level (80 mW/m2) INSOLATION(mW/m2) LOAD RESISTANCE() INPUT VOLTAGE(Volt) INPUT CURRENT(Amp)
80
400
28.75
8.58
80
450
29.75
7.382
80
680
31.26
4.726
Figure 5.13 Interfacing of PV array simulation result with open loop I-V characteristic
Chapter
CONCLUSIONS
P a g e | 44
The open circuit P-V, P-I, I-V curves we obtained from the simulation of the PV array designed in MATLAB environment explains in detail its dependence on the irradiation levels and temperatures. The entire energy conversion system has been designed in MATLB-SIMULINK environment. The various values of the voltage and current obtained have been plotted in the open circuit I-V curves of the PV array at insolation levels of 100 mW/cm2 and 80 mW/cm2. The voltage and current values lie on the curve showing that the coupling of the PV array with the boost converter is proper. However the performance of the photovoltaic device depends on the spectral distribution of the solar radiation.
REFERENCES
P a g e | 46
1.
I.H Atlas, A.M Sharaf, "A photovoltaic Array Simulation Model for MatlabSimulink GUI Environment, Proce. of IEEE International Conference on Clean Electrical Power, ICCEP 2007, Capri, Italy.
2.
Jesus Leyva-Ramos, Member, IEEE, and Jorge Alberto Morales-Saldana," A design criteria for the current gain in Current Programmed Regulators", IEEE Transactions on industrial electronics, Vol. 45, No. 4, August 1998.
3.
K.H. Hussein, I. Muta, T. Hoshino, M. Osakada, "Maximum photovoltaic power tracking: an algorithm for rapidly changing atmospheric conditions", IEE Proc.Gener. Trans. Distrib., Vol. 142,No. 1, January 1995.
4.
Md. Rabiul Islam, Youguang Guo, Jian Guo Zhu, M.G Rabbani, "Simulation of PV Array Characteristics and Fabrication of Microcontroller Based MPPT", Faculty of Engineering and Information technology, University of Technology Sydney, Australia, 6th International Conference on Electrical and Computer Engineering ICECE 2010, 18-20 December 2010, Dhaka, Bangladesh.
5.
W. Xiao, W. G. Dunford, and A. Capel, A novel modeling method for photovoltaic cells, in Proc. IEEE 35th Annu. Power Electron. Spec. Conf. (PESC), 2004, vol. 3, pp. 19501956.
6. 7.
IEEE Standard Definitions of Terms for Solar Cells, 1969. Oliva Mah NSPRI, "Fundamentals of Photovoltaic Materials", National Solar power institute, Inc. 12/21/98. Muhammad H. Rashid, Power Electronics Circuits, Devices and Applications, Third Edition.
8.
9.
Modelling and Control design for DC-DC converter, Power Management group, AVLSI Lab, IIT-Kharagpur.
Nielsen, R. 2005, 'Solar Radiation', http://home.iprimus.com.au/nielsens/ www.earthscan.co.uk/Portals/ Application of non-conventional & renewable energy sources, Bureau of Energy Efficiency.
P a g e | 47