TL084 TL084A - TL084B

GENERAL PURPOSE J-FET QUAD OPERATIONAL AMPLIFIERS

I WIDE COMMON-MODE (UP TO VCC+) AND
DIFFERENTIAL VOLTAGE RANGE

I LOW INPUT BIAS AND OFFSET CURRENT I OUTPUT SHORT-CIRCUIT PROTECTION I HIGH INPUT IMPEDANCE JFET INPUT
STAGE
N DIP14 (Plastic Package)

I INTERNAL FREQUENCY COMPENSATION I LATCH UP FREE OPERATION I HIGH SLEW RATE : 16V/s (typ)
D SO14 (Plastic Micropackage)

p TSSOP14 (Thin Shrink Small Outline Package)

ORDER CODE DESCRIPTION

Part Number Temperature Range Package N D P

The TL084, TL084A and TL084B are high speed JFET input quad operational amplifiers incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view)

TL084M/AM/BM -55C, +125C TL084I/AI/BI -40C, +105C TL084C/AC/BC 0C, +70C Example : TL084CN, TL084CD

N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)

Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + +

14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3

March 2001

1/12

TL084 - TL084A - TL084B

SCHEMATIC DIAGRAM (each amplifier)

VCC

Non-inverting input Inverting input

1 0 0

2 0 0
Output

1 0 0 30k

8.2k

1.3k VCC

35k

1.3k

35k

1 0 0

ABSOLUTE MAXIMUM RATINGS

Symbol VCC Vi Vid Ptot Toper Tstg
1. 2. 3. 4.

Parameter Supply voltage - note 1) Input Voltage - note Power Dissipation Output Short-circuit Duration - note 4) Operating Free-air Temperature Range Storage Temperature Range
2) 3)

TL084M, AM, BM

TL084I, AI, BI

TL084C, AC, BC

Unit V V V mW

18 15 30 680 Infinite -55 to +125 -40 to +105 -65 to +150 0 to +70

Differential Input Voltage - note

C C

All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC + and VCC -. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded

2/12

TL084 - TL084A - TL084B

ELECTRICAL CHARACTERISTICS VCC = 15V, Tamb = +25C (unless otherwise specified)
Symbol Parameter Input Offset Voltage (Rs = 50) Tamb = +25C Vio Tmin Tamb Tmax TL084I,M,AC,AI,AM, BC,BI,BM Min. TL084 TL084A TL084B TL084 TL084A TL084B Typ. 3 3 1 Max. 10 6 3 13 7 5 Min. TL084C Unit Typ. 3 Max. mV 10

13

DVio Iio

Input Offset Voltage Drift Input Offset Current - note Tamb = +25C Tmin Tamb Tmax Input Bias Current -note 1 Tamb = +25C Tmin Tamb Tmax Large Signal Voltage Gain (RL = 2k, Vo = 10V) Tamb = +25C Tmin Tamb Tmax Supply Voltage Rejection Ratio (RS = 50) Tamb = +25C Tmin Tamb Tmax Supply Current, no load, per amplifier Tamb = +25C Tmin Tamb Tmax Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50) Tamb = +25C Tmin Tamb Tmax Output Short-circuit Current Tamb = +25C Tmin Tamb Tmax Output Voltage Swing Tamb = +25C RL = 2k RL = 10k RL = 2k RL = 10k 11 50 25 80 80
1)

10 5 100 4 200 20 25 15 70 70 2.5 2.5 11

10 5 100 4 400 20

V/C pA nA pA nA V/mV

Iib

20

20

Avd

200

200 dB

SVR

86

86 mA

ICC Vicm CMR

1.4 +15 -12 86

1.4 +15 -12 86

2.5 2.5 V dB

80 80 10 10 10 12 10 12 8

70 70 60 60 10 10 10 12 10 12 8

mA 40 40 60 60 V 12 13.5 12 13.5

Ios

Vopp

Tmin Tamb Tmax

SR tr Kov GBP Ri

Slew Rate (Tamb = +25C) Vin = 10V, RL = 2k, CL = 100pF, unity gain Rise Time (Tamb = +25C) Vin = 20mV, RL = 2k, CL = 100pF, unity gain Overshoot (Tamb = +25C) Vin = 20mV, RL = 2k, CL = 100pF, unity gain Gain Bandwidth Product (Tamb = +25C) Vin = 10mV, RL = 2k, CL = 100pF, f= 100kHz Input Resistance

V/s 16 0.1 10 2.5 4 1012 2.5 16 s 0.1 % 10 MHz 4 1012

3/12

TL084 - TL084A - TL084B

Symbol

Parameter Total Harmonic Distortion (Tamb = +25C), f= 1kHz, RL = 2k,CL = 100pF, Av = 20dB, Vo = 2Vpp Equivalent Input Noise Voltage RS = 100, f = 1KHz

TL084I,M,AC,AI,AM, BC,BI,BM Min. Typ. Max. Min.

TL084C Unit Typ. Max. %

THD

0.01

0.01 nV ----------Hz
degrees

en m

15 45 120

15 45 120

Phase Margin Channel Separation Vo1/Vo2 Av = 100

1.

dB

The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature.

4/12

TL084 - TL084A - TL084B

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREE AIR TEMP.

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus LOAD RESISTANCE

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus SUPPLY VOLTAGE

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V)

30 25
RL = 10 k Tamb = +25C

20
15 10

5
0 2 4 6 8 10 12 SUPPLY VOLTAGE ( V) 14 16

5/12

TL084 - TL084A - TL084B

INPUT BIAS CURRENT versus FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION versus FREE AIR TEMP.

100 V CC = INPUT BIAS CURRENT (nA) 10 1 0.1 15V

DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)

1000 400 200 100 40 20 10 4 2 1 -75

V CC = 15V V O = 10V R L = 2k -50

0.01 -50

-25

25

50

75

100

125

-25

25

50

75

100

125

TEMPERATURE (C)

TEMPERATURE (C)

LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT versus FREQUENCY

TOTAL POWER DISSIPATION versus FREE AIR TEMPERATURE

PHASE SHIFT (right scale)

DIFFERENTIAL VOLTAGE AMPLIFICATION (left scale)

180

10

1 100

R = 2kW L C L = 100pF V CC = 15V T amb = +125C

1K 10K 100K 1M 10M FREQUENCY (Hz)

90

TOTAL POWER DISSIPATION (mW)

100

250 225 200 175 150 125 100 75 50 25 0 -75 -50 -25 0 25 50 TEMPERATURE (C)

DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)

V CC = 15V No signal No load

75

100

125

SUPPLY CURRENT PER AMPLIFIER versus FREE AIR TEMPERATURE

SUPPLY CURRENT PER AMPLIFIER versus SUPPLY VOLTAGE

2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50 TEMPERATURE (C)

SUPPLY CURRENT (mA)

V CC = 15V No signal No load

2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0

SUPPLY CURRENT (mA)

Tamb = +25C No signal No load

75

100

125

4 6 10 12 8 SUPPLY VOLTAGE ( V)

14

16

6/12

TL084 - TL084A - TL084B

COMMON MODE REJECTION RATIO versus FREE AIR TEMPERATURE VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE

INPUT AND OUTPUT VOLTAGES (V)

89 COMMON MODE MODE REJECTION RATIO (dB) 88 87 86 85 84 83 -75 -50 -25 0 25 50 75 100 125
R L = 10 k VC C = 15V

6 4 2 0 -2 -4 -6 0
VCC= 15V R L = 2 kW

OUTPUT

INPUT

C L= 100pF Tamb = +25C

0.5

1.5

2.5

3.5

TEMPERATURE (C)

TIME (m s)

OUTPUT VOLTAGE versus ELAPSED TIME

EQUIVALENT INPUT NOISE VOLTAGE versus FREQUENCY

28 24 OUTPUT VOLTAGE (mV)

OVERSHOOT 90%

70 60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 40 30 20 10 0 10 40 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) VCC = 15V A V = 10 R S = 100 T amb = +25C

20 16 12 8 4
10%

0 -4 0

tr 0.1 0.2 0.3 0.4 TIME ( s)

R L = 2k Tamb = +25C 0.5 0.6 0.7

CC

= 15V

TOTAL HARMONIC DISTORTION versus FREQUENCY

1 TOTAL HARMONIC DISTORTION (%) 0.4 0.1 0.04 0.01 0.004 0.001 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) VV = 15V CC CC = 15V 11 AA V V= = VV == 6V 6V (rms) OO (rms) +25C T amb T amb= = +25C

7/12

TL084 - TL084A - TL084B

PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k 1k

eI

1/4 TL084

eo

RL

CL = 100pF

TYPICAL APPLICATIONS AUDIO DISTRIBUTION AMPLIFIER

fO = 100kHz 1M 1/4 TL084 Output A

1 F Input 100k 100k 100k 100k 1/4 TL084 -

1/4 TL084

Output B

1OO F

V CC+

1/4 TL084 Output C

8/12

TL084 - TL084A - TL084B

TYPICAL APPLICATIONS (continued) POSITIVE FEEDBACK BANDPASS FILTER

16k 22 0p F 43k Input 43k 22 0p F 1/4 TL 08 4 43k 1/4 TL 08 4 30k 43k 22 0p F 1/4 TL 08 4 220 pF 43k

16k

30k 43k 1/4 TL 08 4

1.5 k

1.5 k

Output B

Ground Output A

OUTPUT A

OUTPUT B

SECOND ORDER BANDPASS FILTER fo = 100kHz; Q = 30; Gain = 4

CASCADED BANDPASS FILTER fo = 100kHz; Q = 69; Gain = 16

9/12

TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP

Millimeters Dim. Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055

Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100

10/12

TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO)

L C

G c1

a2 b e3 D M e

s E

14 1

8 7 F

Millimeters Dim. Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45 (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007

a1

Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027

Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.

b1

11/12

TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA 14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE
c
k

0,25 mm .010 inch GAGE PLANE L E1 SEATING PLANE C A A2 A1 b e E

8 7

aaa

14

PIN 1 IDENTIFICATION

Millimeters Dim. Min. A A1 A2 b c D E E1 e k l 0.05 0.80 0.19 0.09 4.90 4.30 0 0.50 Typ. Max. 1.20 0.15 1.05 0.30 0.20 5.10 4.50 8 0.75 Min. 0.01 0.031 0.007 0.003 0.192 0.169 0 0.09

L1

Inches Typ. Max. 0.05 0.006 0.041 0.15 0.012 0.20 0.177 8 0.030

1.00

0.039

5.00 6.40 4.40 0.65 0.60

0.196 0.252 0.173 0.025 0.0236

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom http://www.st.com

12/12

This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.