TL072 TL072A - TL072B

Low noise J-FET dual operational amplifiers

Features

Wide common-mode (up to VCC+) and differential voltage range Low input bias and offset current Low noise en = 15nV/Hz (typ) Output short-circuit protection High input impedance JFET input stage Low harmonic distortion: 0.01% (typ) Internal frequency compensation Latch-up free operation High slew rate : 16V/s (typ) D SO8 (Plastic micropackage) Pin connections (top view) N DIP8 (Plastic package)

Description
The TL072, TL072A and TL072B are high speed JFET input dual operational amplifiers incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
1 2 3 4

8 + + 7 6 5

Order codes
Package Part number TL072M/AM/BM TL072I/AI/BI TL072C/AC/BC Example : TL072CN
N = Dual in line package (DIP) D = Small outline package (SO) - also available in tape & reel (DT)

Temperature range N -55C, +125C -40C, +105C 0C, +70C x x x D x x x 1 - Output 1 2 - Inverting input 1 3 - Non-inverting input 1 4 - VCC5 - Non-inverting input 2 6 -Inverting input 2 7 - Output 2 8 - VCC+

December 2006

Rev 3

1/15
www.st.com 15

Contents

TL072 - TL072A - TL072B

Contents
1 2 3 4 5 6 7 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Parameter measurement information . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2/15

TL072 - TL072A - TL072B

Schematic diagram

Schematic diagram
Schematic diagram

VCC

Non-inverting input Inverting input

1 0 0

2 0 0
Output

1 0 0 30k

1/2 TL072

8.2k

1.3k VCC

35k

1.3k

35k

1 0 0

3/15

Absolute maximum ratings

TL072 - TL072A - TL072B

2
Table 1.
Symbol VCC Vi Vid Ptot

Absolute maximum ratings

Absolute maximum ratings
Parameter Supply voltage (1) Input voltage
(2) (3)

TL072M, AM, BM

TL072I, AI, BI 18 15 30 680 Infinite

TL072C, AC, BC

Unit V V V mW

Differential input voltage Power dissipation

Output short-circuit duration (4) Toper Tstg Operating free-air temperature range Storage temperature range -55 to +125

-40 to +105 -65 to +150

0 to +70

C C

1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded.

4/15

TL072 - TL072A - TL072B

Electrical characteristics

3
Table 2.
Symbol

Electrical characteristics
Electrical characteristics at VCC = 15V, Tamb = +25C (unless otherwise specified)
Parameter TL072I,M,AC,AI,AM ,BC,BI,BM Min. Input offset voltage (Rs = 50) Tamb = +25C TL072 TL072A TL072B Tmin Tamb Tmax TL072 TL072A TL072B Input offset voltage drift Input offset current Tamb = +25C Tmin Tamb Tmax
(1)

TL072C Unit Min. Typ. Max.

Typ.

Max.

Vio

3 3 1

10 6 3 13 7 5

10 mV 13

DVio Iio

10 5 100 4 200 20 25 15 70 70 2.5 2.5 11

10 5 100 10 200 20

V/C pA nA pA nA V/mV

Iib

Input bias current (1) Tamb = +25C Tmin Tamb Tmax Large signal voltage gain (RL = 2k Vo = 10V) , Tamb = +25C Tmin Tamb Tmax Supply voltage rejection ratio (RS = 50) Tamb = +25C Tmin Tamb Tmax Supply current, no load Tamb = +25C Tmin Tamb Tmax Input common mode voltage range Common mode rejection ratio (RS = 50) Tamb = +25C Tmin Tamb Tmax Output short-circuit current Tamb = +25C Tmin Tamb Tmax 11 50 25 80 80

20

20

Avd

200

200

SVR

86

86

dB

ICC

1.4 +15 -12 86

1.4 +15 -12 86

2.5 2.5

mA

Vicm

CMR

80 80 10 10

70 70 60 60 10 10

dB

Ios

40

40

60 60

mA

5/15

Electrical characteristics Table 2.

Symbol

TL072 - TL072A - TL072B

Electrical characteristics at VCC = 15V, Tamb = +25C (unless otherwise specified)

Parameter TL072I,M,AC,AI,AM ,BC,BI,BM Min. Output voltage swing Tamb = +25C RL = 2k RL = 10k Tmin Tamb Tmax RL = 2k RL = 10k Slew rate (Tamb = +25C) , Vin = 10V, RL = 2k CL = 100pF, unity gain Rise time (Tamb = +25C) , Vin = 20mV, RL = 2k CL = 100pF, unity gain Overshoot (Tamb = +25C) , Vin = 20mV, RL = 2k CL = 100pF, unity gain Gain Bandwidth Product (Tamb = +25C) , Vin = 10mV, RL = 2k CL = 100pF, f= 100kHz Input resistance Total harmonic distortion (Tamb = +25C) f= 1kHz, RL = 2k L = 100pF, Av = 20dB, ,C Vo = 2Vpp Equivalent input noise voltage RS = 100, f = 1KHz Phase margin Channel separation Av = 100 2.5 Typ. Max. Min. TL072C Unit Typ. Max.

Vopp

10 12 10 12 8

12 13.5

10 12 10 12

12 13.5

SR tr Kov GBP Ri THD

V/s 16 0.1 10 4 1012 0.01 2.5 8 16 s 0.1 % 10 MHz 4 1012 0.01 %

en m Vo1/Vo2

15 45

15 45

nV ----------Hz

degre es dB

120

120

1. The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature.

6/15

TL072 - TL072A - TL072B

Electrical characteristics

Figure 1.

Maximum peak-to-peak output voltage versus frequency

Figure 2.

Maximum peak-to-peak output voltage versus frequency

Figure 3.

Maximum peak-to-peak output voltage versus frequency

Figure 4.

Maximum peak-to-peak output voltage versus free air temperature

Figure 5.

Maximum peak-to-peak output voltage versus load resistance

Figure 6.

Maximum peak-to-peak output voltage versus supply voltage

30 25
RL = 10 k Tamb = +25C

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V)

20
15 10

5
0 2 4 6 8 10 12 SUPPLY VOLTAGE ( V) 14 16

7/15

Electrical characteristics

TL072 - TL072A - TL072B

Figure 7.

Input bias current versus free air temperature

Figure 8.

Large signal differential voltage amplification versus free air temp

100 V CC = INPUT BIAS CURRENT (nA) 10 1 0.1 15V DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)

1000 400 200 100 40 20 10 4 2 1 -25 0 25 50 75 100 125 TEMPERATURE (C) -75

V CC = 15V V O = 10V R L = 2k -50 -25 0 25 50 75 100 125

0.01 -50

TEMPERATURE (C)

Figure 9.

Large signal differential voltage amplification and phase shift versus frequency

Figure 10. Total power dissipation versus free air temperature

100
PHASE SHIFT (right scale)

DIFFERENTIAL VOLTAGE AMPLIFICATION (left scale)

180

10

1 100

R = 2kW L C L = 100pF V CC = 15V T amb = +125C

1K 10K 100K 1M 10M FREQUENCY (Hz)

90

TOTAL POWER DISSIPATION (mW)

250 225 200 175 150 125 100 75 50 25 0 -75 -50 -25 0 25 50 TEMPERATURE (C)

DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)

V CC = 15V No signal No load

75

100

125

Figure 11. Supply current per amplifier versus Figure 12. Common mode rejection ratio free air temperature versus free air temperature
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50 TEMPERATURE (C) 89 COMMON MODE MODE REJECTION RATIO (dB) V CC = 15V No signal No load 88 87 86 85 84 83 -75 -50 -25 0 25 50 75 100 125
R L = 10 k VC C = 15V

SUPPLY CURRENT (mA)

75

100

125

TEMPERATURE (C)

8/15

TL072 - TL072A - TL072B

Electrical characteristics

Figure 13. Voltage follower large signal pulse response

INPUT AND OUTPUT VOLTAGES (V) 6 INPUT

Figure 14. Output voltage versus elapsed time

28 OUTPUT VOLTAGE (mV)

4 2 0 -2 -4 -6 0

OUTPUT

24
OVERSHOOT

20 16 12 8 4
10%

90%

VCC= 15V R L = 2 kW

CC

= 15V

C L= 100pF Tamb = +25C

0 -4 0

tr 0.1 0.2 0.3 0.4 TIME ( s)

R L = 2k Tamb = +25C 0.5 0.6 0.7

0.5

1.5

2.5

3.5

TIME (ms)

Figure 15. Equivalent input noise voltage versus frequency

70 60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 40 30 20 10 0 10 40 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz)

Figure 16. Total harmonic distortion versus frequency

1 TOTAL HARMONIC DISTORTION (%)

VCC = 15V A V = 10 R S = 100 T amb = +25C

0.4 0.1 0.04 0.01 0.004 0.001 100

V V = = 15V 15V CC CC 1 A A V= = 1 V V V O (rms) = 6V O (rms) = 6V T amb = = +25C T amb +25C

400

1k

4k

10k

40k

100k

FREQUENCY (Hz)

9/15

Parameter measurement information

TL072 - TL072A - TL072B

Parameter measurement information

Figure 17. Voltage follower

Figure 18.

Gain-of-10 inverting amplifier

10k 1k

eI

1/2 TL072

eo

RL

CL = 100pF

10/15

TL072 - TL072A - TL072B

Typical applications

Typical applications
Figure 19. 100kHz quadruple oscillator
1N 4148 18k * -15V

18pF 18pF 88.4k 6 sin t 18pF 88.4k

1k

1/2 TL072
88.4k

1/2 TL072
1k

6 cos t

1N 4148

18k * +15V

* These resistor values may be adjusted for a symmetrical output

11/15

Package mechanical data

TL072 - TL072A - TL072B

Package mechanical data

Figure 20. 8-pin plastic DIP

Millimeters Dim. Min. A a1 B b b1 D E e e3 e4 F i L Z 3.18 7.95 2.54 7.62 7.62 6.6 5.08 3.81 1.52 0.125 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 9.75 0.313 Typ. 3.32 0.020 0.045 0.014 0.008 Max. Min.

Inches Typ. 0.131 Max.

0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060

12/15

TL072 - TL072A - TL072B Figure 21. 8-pin plastic micropackage (SO)

Package mechanical data

Millimeters Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 3.8 0.4 4.8 5.8 1.27 3.81 4.0 1.27 0.6 8 (max.) 0.150 0.016 5.0 6.2 0.65 0.35 0.19 0.25 0.1 Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 0.026 0.014 0.007 0.010 45 (typ.) 0.189 0.228 0.004 Min.

Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020

0.197 0.244 0.050 0.150 0.157 0.050 0.024

13/15

Revision history

TL072 - TL072A - TL072B

Revision history
Date 28-Mar-2001 2-Apr-2004 4-Dec-2006 Revision 1 2 3 Initial release. Correction to pin connection diagram on cover page. Unpublished. Modified graphics in package mechanical data. Changes

14/15

TL072 - TL072A - TL072B

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to STs terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USERS OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com

15/15