TL062, TL062A, TL062B

Low-power JFET dual operational amplifiers

Features

Very low power consumption: 200 A Wide common-mode (up to VCC+) and differential voltage ranges Low input bias and offset currents Output short-circuit protection High input impedance JFET input stage Internal frequency compensation Latch up free operation High slew rate: 3.5 V/s D SO-8 (Plastic micropackage) N DIP8 (Plastic package)

Description
The TL062, TL062A and TL062B are high-speed JFET input single operational amplifiers. Each of these JFET input operational amplifiers incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and a low offset voltage temperature coefficient. Pin connections (top view)

1 2 3 4
+ +

8 7 6 5

1 - Output 1 2 - Inverting input 1 3 - Non-inverting input 1 4 - VCC5 - Non-inverting input 2 6 - Inverting input 2 7 - Output 2 8 - VCC+

March 2010

Doc ID 2294 Rev 3

1/16
www.st.com 16

Schematic diagram

TL062, TL062A, TL062B

1
Figure 1.

Schematic diagram
Schematic diagram
VC C

220
Inverting input Non-inverting input

64 45 k 270

Output

1/2 TL062

3.2 k

4.2 k

100

V CC

2/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Absolute maximum ratings and operating conditions

2
Table 1.
Symbol VCC Vi Vid Ptot

Absolute maximum ratings and operating conditions

Absolute maximum ratings
Value Parameter TL062M, AM, BM TL062I, AI, BI Supply voltage (1) Input voltage
(2)

Unit TL062C, AC, BC V V V mW 18 15 30 680

(4)

Differential input voltage(3) Power dissipation Output short-circuit duration

Infinite -65 to +150 -65 to +150 -65 to +150 C

Tstg

Storage temperature range Thermal resistance junction to ambient(5) (6) SO-8 DIP8 Thermal resistance junction to case(5) (6) SO-8 DIP8 HBM: human body model(7)

Rthja

125 85

C/W

Rthjc

40 41 900 150

C/W

V V kV

ESD

MM: machine model

(8) (9)

CDM: charged device model

1.5

1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 100 pF discharged through a 1.5 k resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 ), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground.

Table 2.
Symbol VCC Toper

Operating conditions
Parameter Supply voltage range Operating free-air temperature range -55 to +125 TL062M, AM, BM TL062I, AI, BI 6 to 36 -40 to +105 0 to +70 TL062C, AC, BC Unit V C

Doc ID 2294 Rev 3

3/16

Electrical characteristics

TL062, TL062A, TL062B

3
Table 3.
Symbol

Electrical characteristics
VCC = 15 V, Tamb = +25C (unless otherwise specified)
TL062M Parameter Min Input offset voltage (RS = 50) Tamb = +25C Tmin Tamb Tmax Temperature coefficient of input offset voltage (RS = 50) Input offset current (1) Tamb = +25C Tmin Tamb Tmax Input bias current (1) Tamb = +25C Tmin Tamb Tmax Input common mode voltage range Output voltage swing (RL = 10k) Tamb = +25C Tmin Tamb Tmax Large signal voltage gain , RL = 10k Vo = 10V, Tamb = +25C Tmin Tamb Tmax Gain bandwidth product Tamb = +25C, RL =10k CL = 100pF , Input resistance Common mode rejection ratio RS = 50 Supply voltage rejection ratio RS = 50 Supply current, no load Tamb = +25C, no load, no signal Channel separation Av = 100, Tamb = 25C Total power consumption Tamb = +25C, no load, no signal Slew rate Vi=10V, RL = 10k CL= 100pF, Av=1 , 1.5 80 80
11.5

TL062I Max Min Typ Max Min

TL062C Unit Typ Max

Typ

Vio

6 15

6 9

15 20

mV

DVio

10

10

10 100 10 200 20 11 5 200 5 400 10

V/C

Iio

100 20 200 50
11.5

pA nA pA nA V

Iib

30 +15 -12 27

30 +15 -12 27

30 +15 -12 27

Vicm

Vopp

20 20

20 20

20 20

Avd

4 4

4 4

3 3

V/mV

GBP Ri CMR SVR ICC Vo1/Vo2 PD SR

1 1012 86 95 200 120 6 3.5 7.5 1.5 250 80 80

1 1012 86 95 200 120 6 3.5 7.5 1.5 250 70 70

1 1012 76 95 200 120 6 3.5 7.5 250

MHz dB dB A dB mW V/s

4/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B Table 3.

Symbol

Electrical characteristics

VCC = 15 V, Tamb = +25C (unless otherwise specified) (continued)

TL062M Parameter Min Rise time , Vi = 20mV, RL = 10k CL = 100pF, Av = 1 Overshoot factor (see Figure 15) , Vi = 20mV, RL = 10k CL = 100pF, Av = 1 Equivalent input noise voltage RS = 100, f = 1kHz Typ Max Min Typ Max Min Typ Max s TL062I TL062C Unit

tr

0.2

0.2

0.2

Kov

10

10

10

%
nV ----------Hz

en

42

42

42

1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible.

Table 4.
Symbol

VCC = 15 V, Tamb = +25C (unless otherwise specified)

TL062AC, AI, AM Parameter Min. Input offset voltage (RS = 50) Tamb = +25C Tmin Tamb Tmax Temperature coefficient of input offset voltage (RS = 50) Input offset current (1) Tamb = +25C Tmin Tamb Tmax Input bias current (1) Tamb = +25C Tmin Tamb Tmax Input common mode voltage range Output voltage swing (RL = 10k) Tamb = +25C Tmin Tamb Tmax Large signal voltage gain , RL = 10k Vo = 10V, Tamb = +25C Tmin Tamb Tmax Gain bandwidth product Tamb = +25C, RL =10k CL = 100pF , Input resistance Common mode rejection ratio RS = 50 80 11.5 Typ. Max. Min. Typ. Max. TL062BC, BI, BM Unit

Vio

6 7.5

3 5

mV

DVio

10

10

V/C

Iio

100 3 200 7 11.5

100 3 200 7

pA nA nA

Iib

30 +15 -12 27

30 +15 -12 27

Vicm

Vopp

20 20

20 20

Avd

4 4

4 4

V/mV

GBP Ri CMR

1 1012 86 80

1 1012 86

MHz dB

Doc ID 2294 Rev 3

5/16

Electrical characteristics Table 4.

Symbol

TL062, TL062A, TL062B

VCC = 15 V, Tamb = +25C (unless otherwise specified) (continued)

TL062AC, AI, AM Parameter Min. Typ. 95 200 120 6 1.5 3.5 0.2 10 42 7.5 1.5 250 Max. Min. 80 Typ. 95 200 120 6 3.5 0.2 10 42 7.5 mW V/s s %
nV ----------Hz

TL062BC, BI, BM Unit Max. dB 250 A

SVR ICC Vo1/Vo2 PD SR tr Kov en

Supply voltage rejection ratio RS = 50 Supply current, no load Tamb = +25C, no load, no signal Channel separation Av = 100, Tamb = +25C Total power consumption Tamb = +25C, no load, no signal Slew rate Vi = 10V, RL = 10k CL = 100pF, Av = 1 , Rise time , Vi = 20mV, RL = 10k CL = 100pF, Av = 1 Overshoot factor (see Figure 15) Vi = 20mV, RL = 10k CL = 100pF, Av = 1 , Equivalent input noise voltage RS = 100, f = 1kHz

80

1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible.

6/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Electrical characteristics

Figure 2.

Maximum peak-to-peak output voltage versus supply voltage

Figure 3.

Maximum peak-to-peak output voltage versus free air temperature

Maximum peak-to-peak output voltage (V)

RL = 10 k Tamb = + 25C

Maximum peak-to-peak output voltage (V)

VCC = +/- 15 V RL = 10 k

Supply voltage (V)

Free air temperature (C)

Figure 4.

Maximum peak-to-peak output voltage versus load resistance

Figure 5.

Maximum peak-to-peak output voltage versus frequency

Maximum peak-to-peak output voltage (V)

Maximum peak-to-peak output voltage (V)

VCC = +/- 15 V VCC = +/- 12 V VCC = +/- 5 V VCC = +/- 2 V

RL = 10 k Tamb = + 25C

VCC = +/- 15 V Tamb = + 25C

Load resistance (k)

Frequency (Hz)

Figure 6.

Differential voltage amplification versus free air temperature

Figure 7.

Large signal differential voltage amplification and phase shift versus frequency

10

6 10

VCC = +/- 5 V to +/- 15 V RL = 2 k Tamb = + 25C Differential voltage amplification (left scale) Phase shift (right scale)

Differential voltage amplification (V/mV)

Differential voltage amplification (V/V)

7 4

105 4 10

3 10 102
101 1

45
90 135

2
VCC = +/- 15 V RL = 10 k

1 -75 -50 -25 0 25 50 75 100 125

10

100

1k

10k

100k

1M

180 10M

Free air temperature (C)

Frequency (Hz)

Doc ID 2294 Rev 3

7/16

Electrical characteristics

TL062, TL062A, TL062B

Figure 8.

Supply current per amplifier versus Figure 9. supply voltage

250

Supply current per amplifier versus free air temperature

250

Supply current (A)

150 100
Tamb = + 25C

Supply current (A)

200

200
150 100
VCC = +/- 15 V

50

No signal no load

50

No signal no load

0
0 2 4 6 8 10 12 14

0
16
-75 -50 -25 0 25 50 75 100 125

Supply voltage (+/- V)

Free air temperature (C)

Figure 10. Total power dissipated versus free air temperature

30

Figure 11. Common-mode rejection ratio versus free air temperature

Common mode rejection ratio (dB)
87 86 85 84 83 82 81 -75
VCC = +/- 15 V RL = 10 k

Total power dissipated (mW)

25 20 15 10 5 0 -75

VCC = +/- 15 V No signal no load

-50

-25

25

50

75

100

125

-50

-25

25

50

75

100

125

Free air temperature (C)

Free air temperature (C)

Figure 12. Normalized unity gain bandwidth slew rate and phase shift versus temperature
Normalized unity-gain bandwidth and slew rate
1.3
1.2 1.1
Unity-gain bandwidth (left scale)

Figure 13. Input bias current versus free air temperature

100
1.02 1.01

Normalized phase shift

Phase shift (right scale)

Input bias current (nA)

1.03

VCC = +/- 15 V

10
1 0.1

1 0.9
0.8
VCC = +/- 15 V RL = 10 k f = B1 for phase shift

Slew rate (left scale)

1 0.99
0.98

0.7 -75 -50

-25

25

50

0.97 75 100 125

0.01 -50

-25

25

50

75

100

125

Free air temperature (C)

Free air temperature (C)

8/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Electrical characteristics

Figure 14. Voltage follower large signal pulse response

Input and output voltages (V)
6

Figure 15. Output voltage versus elapsed time

28

Output voltage (mV)

Input

24 20 16 12 8 4 0 -4

Overshoot 90%

2
0 -2 -4 -6 0 2 4 6
VCC = +/- 15 V RL = 10 k CL = 100 pF Tamb = + 25C

Output

VCC = +/- 15 V 10% tr RL = 10 k Tamb = + 25C

10

0.2

0.4

0.6

0.8

12

14

Time (s)

Time (s)

Figure 16. Equivalent input noise voltage versus frequency

100

Equivalent input noise voltage (nV/VHz)

90 80 70 60 50 40 30
20 10 0 10

VCC = +/- 15 V RS = 100 Tamb = + 25C

40

100

400 1k

4k

10k

40k 100k

Frequency (Hz)

3.1

Parameter measurement information

Figure 18. Gain of 10 inverting amplifier

Figure 17. Voltage follower

10 k
-

1 k
eI
eo

1/2 TL062
eI

1/2 TL062 RL

eo

CL = 100 pF

RL = 10 k

CL = 100 pF

Doc ID 2294 Rev 3

9/16

Typical applications

TL062, TL062A, TL062B

Typical applications

Figure 19. 100 kHz quadrature oscillator

1N 4148 18 k * -15 V

18 pF 18 pF 88.4 k 6 sin t 18 pF 88.4 k 1/2 TL062

1 k

1/2 TL062
88.4 k

6 cos t 1 k

1N 4148

18 k * +15 V

1. These resistor values may be adjusted for a symmetrical output.

10/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Package information

Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.

Doc ID 2294 Rev 3

11/16

Package information

TL062, TL062A, TL062B

5.1

DIP8 package information

Figure 20. DIP8 package mechanical drawing

Table 5.

DIP8 package mechanical data

Dimensions

Ref. Min. A A1 A2 b b2 c D E E1 e eA eB L 2.92 0.38 2.92 0.36 1.14 0.20 9.02 7.62 6.10

Millimeters Typ. Max. 5.33 0.015 3.30 0.46 1.52 0.25 9.27 7.87 6.35 2.54 7.62 10.92 3.30 3.81 0.115 4.95 0.56 1.78 0.36 10.16 8.26 7.11 0.115 0.014 0.045 0.008 0.355 0.300 0.240 Min.

Inches Typ. Max. 0.210

0.130 0.018 0.060 0.010 0.365 0.310 0.250 0.100 0.300

0.195 0.022 0.070 0.014 0.400 0.325 0.280

0.430 0.130 0.150

Note:

Dimensions "D" and "E1" do not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.25 mm in total (both sides). Datum plane "H" coincides with the bottom of the lead, where the lead exits the body.

12/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Package information

5.2

SO-8 package information

Figure 21. SO-8 package mechanical drawing

Table 6.

SO-8 package mechanical data

Dimensions

Ref. Min. A A1 A2 b c D E E1 e h L L1 k ccc 0 0.25 0.40 0.10 1.25 0.28 0.17 4.80 5.80 3.80

Millimeters Typ. Max. 1.75 0.25 0.004 0.049 0.48 0.23 4.90 6.00 3.90 1.27 0.50 1.27 1.04 8 0.10 1 0.010 0.016 5.00 6.20 4.00 0.011 0.007 0.189 0.228 0.150 Min.

Inches Typ. Max. 0.069 0.010

0.019 0.010 0.193 0.236 0.154 0.050 0.020 0.050 0.040 8 0.004 0.197 0.244 0.157

Doc ID 2294 Rev 3

13/16

Ordering information

TL062, TL062A, TL062B

Ordering information
Table 7. Order codes
Temperature range Package Packing Marking TL062MN TL062AMN TL062BMN 062M 062AM 062BM TL062IN TL062AIN TL062BIN 062I 062AI 062BI TL062CN TL062ACN TL062BCN 062C 062AC 062BC

Part number TL062MN TL062AMN TL062BMN

DIP8 -55C, +125C

Tube

TL062MD/MDT TL062AMD/AMDT TL062BMD/BMDT TL062IN TL062AIN TL062BIN -40C, +105C TL062ID/IDT TL062AID/AIDT TL062BID/BIDT TL062CN TL062ACN TL062BCN 0C, +70C TL062CD/CDT TL062ACD/ACDT TL062BCD/BCDT

SO-8

Tube or tape & reel

DIP8

Tube

SO-8

Tube or tape & reel

DIP8

Tube

SO-8

Tube or tape & reel

14/16

Doc ID 2294 Rev 3

TL062, TL062A, TL062B

Revision history

Revision history
Table 8.
Date 28-Mar-2001

Document revision history

Revision 1 Initial release. Added values for Rthja and Rthjc in Table 1: Absolute maximum ratings. Added Table 2: Operating conditions. Updated format. Updated document format. Added TL062A and TL062B in title on cover page. Updated package information in Chapter 5. Changes

27-Jul-2007

15-Mar-2010

Doc ID 2294 Rev 3

15/16

TL062, TL062A, TL062B

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to STs terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USERS OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com

16/16

Doc ID 2294 Rev 3