Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 73 views

    DI87

    Uploaded by

    Erln Lima
    The document provides instructions for inspecting the cruise control ECU power source circuit on vehicles without ETCS-i. It describes the circuit, shows the wiring diagram, and lists the following inspection procedures: 1. Check for continuity of the ECU-IG fuse. 2. Check for 10-16V between terminals B and GND of the ECU connector with the ignition switch ON. 3. Check for less than 1 ohm of resistance between terminal GND of the ECU connector and body ground.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    DI87

    Uploaded by

    Erln Lima
    73 views3 pages
    The document provides instructions for inspecting the cruise control ECU power source circuit on vehicles without ETCS-i. It describes the circuit, shows the wiring diagram, and lists the following inspection procedures: 1. Check for continuity of the ECU-IG fuse. 2. Check for 10-16V between terminals B and GND of the ECU connector with the ignition switch ON. 3. Check for less than 1 ohm of resistance between terminal GND of the ECU connector and body ground.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for inspecting the cruise control ECU power source circuit on vehicles without ETCS-i. It describes the circuit, shows the wiring diagram, and lists the following inspection procedures: 1. Check for continuity of the ECU-IG fuse. 2. Check for 10-16V between terminals B and GND of the ECU connector with the ignition switch ON. 3. Check for less than 1 ohm of resistance between terminal GND of the ECU connector and body ground.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    73 views3 pages

    DI87

    Uploaded by

    Erln Lima
    The document provides instructions for inspecting the cruise control ECU power source circuit on vehicles without ETCS-i. It describes the circuit, shows the wiring diagram, and lists the following inspection procedures: 1. Check for continuity of the ECU-IG fuse. 2. Check for 10-16V between terminals B and GND of the ECU connector with the ignition switch ON. 3. Check for less than 1 ohm of resistance between terminal GND of the ECU connector and body ground.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    DI–757

    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/o ETCS–i)


    DI8ZO–03

    ECU Power Source Circuit

    CIRCUIT DESCRIPTION
    The ECU power source supplies power to the actuator and sensors, etc., when terminal GND and the cruise
    control ECU case are grounded.

    WIRING DIAGRAM
    C17
    I14 Cruise Control ECU
    Ignition SW J/B No. 1 J/B No. 3
    2 ECU–IG 1 4 3
    W B–Y Y–R Y–R
    1I 1G 3H 3H B
    2 4 9
    AM1 IG1
    2

    2
    AM1
    1
    R/B No. 2
    1
    ALT
    2

    2
    W

    Battery

    I26139

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 1019


    DI–758
    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/o ETCS–i)

    INSPECTION PROCEDURE

    1 Check ECU–IG fuse.

    J/B No. 1 PREPARATION:


    ECU–IG Remove the ECU–IG fuse from the J/B No. 1.
    Fuse CHECK:
    Check the continuity of the ECU–IG fuse.
    OK:
    Continuity

    NG Replace ECU–IG fuse.


    I21973

    OK

    2 Check voltage between terminals B and GND of cruise control ECU connector.

    PREPARATION:
    ON (a) Remove the ECU with the connector being connected.
    B (b) Turn the ignition switch ON.
    GND CHECK:
    Measure the voltage between terminals B and GND of the ECU
    connector.
    OK:
    10 – 16 V

    (–) (+)

    OK Proceed to next circuit inspection shown in


    I22456 problem symptoms table (See page DI–730).

    NG

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 1020


    DI–759
    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/o ETCS–i)

    3 Check resistance between terminal GND of cruise control ECU connector and
    body ground.

    CHECK:
    Measure the resistance between terminal GND of the ECU con-
    nector and the body ground.
    OK:
    Resistance: Below 1 Ω
    GND

    I22457 NG Repair or replace harness or connector.

    OK

    Check and repair harness and connector be-


    tween cruise control ECU and battery (See
    page DI–730).

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 1021

    You might also like