Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
2K views

Intensity Modulation

The document describes an experiment to study the gain characteristics of a linear intensity modulation system using an optical fiber. Key aspects include: 1) The aim is to measure the gain (Vo/Vin) for varying input signal amplitudes (Vin) at a fixed carrier power (Po) and signal frequency (F0). 2) Equipment used includes a laser diode transmitter, receiver, optical fiber cable, function generator, and oscilloscope. 3) Procedures describe setting the carrier power (Po), applying an AC input (Vin) from the function generator, measuring the output (Vout) on the oscilloscope, and recording gain values for different Vin amplitudes. 4) Observations

Uploaded by

anon-323096
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
2K views

Intensity Modulation

The document describes an experiment to study the gain characteristics of a linear intensity modulation system using an optical fiber. Key aspects include: 1) The aim is to measure the gain (Vo/Vin) for varying input signal amplitudes (Vin) at a fixed carrier power (Po) and signal frequency (F0). 2) Equipment used includes a laser diode transmitter, receiver, optical fiber cable, function generator, and oscilloscope. 3) Procedures describe setting the carrier power (Po), applying an AC input (Vin) from the function generator, measuring the output (Vout) on the oscilloscope, and recording gain values for different Vin amplitudes. 4) Observations

Uploaded by

anon-323096
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

INTENSITY MODULATION OF LASER OUTPUT

THROGH AN OPTICAL FIBER


AIM:
The aim of the experiment is to study the following ac characteristics of a linear
intensity modulation system:
(i) gian characteristics of FO linear intensity modulation system Vin(ac) Vs
Vo(ac) for fixed carrier power Po and signal frequency F0.

EQUIPMENT REQUIRED:
S.No EQUIPMENT QUANTITY
1. LASER Diode transmitter Kit 1
2. LASER Diode receiver Kit 1
3. Optical Fiber cable 1
4. Function Generator 1
5. CRO 1

CIRCUIT DIAGRAM:

LASER Diode Transmitter Unit LASER Diode Receiver Unit

LASER
OF
SET Po Cable
Fo PIN

Oscilloscope
Function
Generator

THEORY:
Linear Intensity Modulator: slection of optimum carrier power is essential to
minimize distortion.Limiting depth of modulation also ensures distortion free
transmission.
(a) Select an IF(dc) =10mA(corresponding to carrier power Po of -14dbm to 17 dbm)
as dc operating point.
(b) (b) For Vin(ac) = 200mv(P-P), we get IF(ac)=2mA(p-P) corresponding to
variations from 9mA to 11mA.this is well within the linear region.The modulation
may be distortion free for a Vin(ac) of 1V(p-p).One may compute values of IF(dc)
or Po(CW) (optical carrier power) for different peak to peak input signals,Vin(ac).
(c) The loss due to the optical fiber cable may be overcome by proper selection of
demodulator again.

PROCEDURE:
1. Connect one end of cable1 to the Fo port of analog transmitter. First connected to
FO pin to set the carrier power level ,Po .After setting Po, it is removed and
connected to FO PT to study the system.
2. Connect Vin(ac) and GND on the Transmitter unit to a function generator(10Hz to
500 KHz sinewave O/P,10mV to 2Vp-p O/P)
3. Connect Vout of receiver unit to CH2 of a dual trace oscilloscope. Give the function
generator output to CH1.
4. plug the AC mains. Adjust the SET Po Knob to set the optical carrier power to
15dbm with Vin disconnected from the function generator .Disconnect cable1 from
Fo PIN port and connect to FOPT.
5. Connect Vin to function generator. Set signal frequency and amplitude to 2KHZ and
100mv respectively .Observe the transmitted (Vin) and received(Vout) signals on
the oscilloscope with identical range settings. Coincide the two waveforms.A djust
SET Rin suitably to obtain the unity gain for system.
6. Next,set Vin o suitable values from 10mV to 2Vp-p and note down values of
Vout.Tabulate and plot a graph Vout Vs Vin .Compute Vout/Vin.

RECORD OF OBSERVATIONS:

Frequency,fo= 2KHz,carrier level Po=-15dbm,System Gain=1.0

Vin (mV) Vout(mV) Gain=Vout/Vin


20
40
:
2000

MODEL GRAPH:
Vout

Vin
RESULT:

Thus gain characteristics are obtained.

You might also like