Control Instruments

Control and Measuring Instruments
innovation
> technology > future
Kontrol 500-502
Parameters
Single and twin-parameter control instruments
The Kontrol 500-series are advanced controllers designed for high-end applications. The units feature independent proportional PID-enabled control outputs, RS 485 serial port with MODBUS protocol, USB port on request, probe quality checking, a variety of outputs and full data logging capability. The user has full programming authority.
Features
Graphic display and Keypad 128 by 64 pixel resolution monochrome display with graphic icons to show digital output status, Data logging, washing cycle, alarms. Simultaneous flashing values for the measurement (numeric + bargraph) and temperature readings. Analogue scrolling output values. Five control keys for instrument calibration and configuration. Enclosure Box and Power Supply Wall mounting ABS plastic material IP65 (144x144) Panel mounting IP54 (96x96) Universal Power Supply 100240 Vac 50/60 Hz Manual controls The user-friendly programming step menu makes starting up and checking the control and dosing system easy.
Kontrol 500-502
02 seko
l pH / ORP l Conductivity l Dissolved Oxygen l Chlorine l Chlorine Dioxide l Hydrogen Peroxide l Ozone l Peracetic Acid l Turbidity l Suspended solids
Applications
l Waste Water l Drinking Water l Cooling Towers l Boiler l Legionella disinfection l Reverse Osmosis l Sludge l Crate Wash l Galvanic Process l Dioxide Station l CIP l Irrigation l Swimming Pool l Fish Farming l Sea water l Dairy
> water & industry > control and measuring instruments
Measure range
Code Description
pH Data logging Internal Flash Memory with records interval from 1 to 99 min. (near to 16000 records) Visualization key for stored data in tabular and graphic form. Type: Circular (F.I.F.O.) or Filling. RS485 Serial port To set-up and to acquire/capture real time data or to download stored data on PC or laptop (Communication Software Master Controller NET required). MODBUS RTU communication protocol USB port To download recorded data on removable memory Usb Pen Drive (upon request). Measure Input High measuring resolution with probe quality control. Modular measuring system Chlorine measure for sea water application. Digital Input Dedicated to disable all controller output functions. Current outputs 420mA Galvanic isolation Two independent programmable Output Measures with PID routine regulation. Relay Outputs Four independent relais, two set points, one alarm remote output, on backwashing probe output. On/OFF, Timed routine function setting. ORP Conductivity Inductive Conductivity Dissolved Oxygen Chlorine and Chlo. Dioxide Hydrogen Peroxide Ozone (03) Peracetic Acid Turbidity Suspended Solids Turbidity Temperature
0 14,00 pH 1500 mV 020 /200 /2.000 /20.000 /200.000 S 010.000 /10.000 /100.000 /999.999 S 020,0 ppm or mg/l - 0200% SAT 00,50/1,00 /2,00 /5,00 /10,0 /20,0 /200,0 ppm 0500 /1000 /2000 /10.000 /100.000 ppm 00,5 /2,00 /5,00 /10,00 ppm 0500 /2000 /10.000 /20.000 ppm 0,001,00 /10,0 /100 NTU/FTU 0,04,00 /40,0 /400 /4.000 NTU/FTU - 030 gr/l
with PT100/PT1000 0100C (32212 F)
Product line
Code
Kontrol 500 Single parameter

Description for pH or ORP values for Conductivity values for Inductive Conductivity values for Dissolved Oxygen values for Chlorine values for Turbidity values for Suspended Solid Turbidity values
The units Software enables the following measures: H2O2 - O3 - ClO2 - C2H4O3
Model Kontrol PR 500 Kontrol CD 500 Kontrol ID 500 Kontrol OX 500 Kontrol CL 500 Kontrol TB 500 Kontrol TS 500
K500PR K500CD K500ID K500OX K500CL K500T1 K500T2
Product line
K502PR K502PD K502PO K502PC K502CC K502TO K502TX K502PI
Kontrol 502 Double parameters

for pH/ORP - pH/ORP values for pH/ORP - Conductivity values for pH/ORP - Dissolved Oxyge values for pH/ORP - Chlorine values for Conductivity - Chlorine values for Turbidity - Dissolved Oxygen values for Suspended Solids Turbidity - Dissolved Oxygen values for pH/ORP - Inductive Conductivity values innovation
Kontrol PR-PR 502 Kontrol PR-CD 502 Kontrol PR-OX 502 Kontrol PR-CL 502 Kontrol CD-CL 502 Kontrol TB-OX 502 Kontrol TS-OX 502 Kontrol PR-ID 502
03
Kontrol 200
Single-parameter control instrument
The Kontrol 200-series are advanced controllers designed for simpler high-end applications. The units feature an independent proportional control output, probe quality checking and a variety of outputs . The user has full programming authority.
Parameters
l pH / ORP l Conductivity l Dissolved Oxygen l Chlorine l Chlorine Dioxide l Hydrogen Peroxide l Ozone l Peracetic Acid l Turbidity
Features
Graphic display and Keypad 128 by 64 pixel resolution monochrome display with graphic icons to show digital output status, washing cycle, alarms. Simultaneous flashing values for the measurement (numeric + bargraph) and temperature readings. Four control keys for instrument calibration and configuration. Enclosure Box and Power Supply Wall mounting ABS plastic material IP65 (144x144) Panel mounting IP54 (96x96) Universal Power Supply 100>240 Vac 50/60 Hz
Kontrol 200
04 seko
Applications
Measure range
Code Description
pH Manual controls The user-friendly programming step menu makes starting up and checking the control and dosing system easy. Measure Input High measuring resolution with probe quality control. A modular measuring system Chlorine measure in sea water application. Digital Input Dedicated to disable all controller output functions Current outputs 420mA Galvanic isolation One independent programmable Output Measures. Relay Outputs Four independent relais, two set points, one alarm remote output, on backwashing probe output. On/OFF, Timed routine function setting. ORP Conductivity Inductive Conductivity Dissolved Oxygen Chlorine and Chlo. Dioxide Hydrogen Peroxide Ozone (03) Peracetic Acid Turbidity Temperature
0 14,00 pH 1500 mV 020 /200 /2.000 /20.000 /200.000 S 010.000 /10.000 /100.000 /999.999 S 020,0 ppm or mg/l - 0200% SAT (*) 00,50/1,00 /2,00 /5,00 /10,0 /20,0 /200,0 ppm 0500 /1000 /2000 /10.000 /100.000 ppm 00,5 /2,00 /5,00 /10,00 ppm 0500 /2000 /10.000 /20.000 ppm 0,0040 NTU/FTU (**)
with PT100/PT1000 0100C (32212 F)
(*): Dissolved Oxygen probe Oxysens only (**): Turbidimetric probe 462/SWP only
Product line
Code

Description for pH or ORP values for Conductivity values for Inductive Conductivity values for Dissolved Oxygen values for Chlorine values for Turbidity values
By software it is available the following measures: H2O2 - O3 - ClO2 - C2H4O3
Model Kontrol PR 200 Kontrol CD 200 Kontrol ID 200 Kontrol OX 200 Kontrol CL 200 Kontrol TB 200
K200PR K200CD K200ID K200OX K200CL K200TB
innovation
05
Kontrol 800
Multi-parameter control instrument
The Kontrol 800 is a dedicated multi-parameter controller for complex applications that require a number of chemical parameters to be checked at the same time. The unit features independent proportional control output measures, two programmable frequency outputs, RS 485 serial port with MODBUS protocol, three relais outputs, probe quality checking and Data logging capability.
Parameters
l pH / ORP l Conductivity l Chlorine l Chlorine Dioxide
Features
Graphic display and Keypad Simultaneous value of the measure, Temperature and Relay status. 4-line, 20-character Alphanumeric Display. Seven control keys for instrument calibration and configuration. Enclosure Box and Power Supply Wall mounting ABS plastic material IP65. Universal Power Supply 100240 Vac 50/60 Hz Manual controls The user-friendly programming step menu makes starting up and checking the control and dosing system easy. Data logging Internal Flash memory to load record measures values. Type: Circular (F.I.F.O.) or Filling.
Kontrol 800
06 seko
Applications
Measure range
Code Description
pH RS485 Serial port For set-up and real-time data acquisition from remote or for stored data download on PC or laptop (Communication software Sekonet required). MODBUS RTU communication protocol. Measure Input High measuring resolution with probe quality control. Modular measuring system. Chlorine measure in sea water application. Digital Input Double channel, Voltage Input and Reed level input to disable all function controller output. Current outputs 420mA Galvanic isolation Two (2) programmable Output Measure. Frequency Outputs 1120 Pulse/Minutes open collector Isolation channel. Two (2) programmable Output Measure. Relay Outputs Three (3) independent relais, Three (3) set point measure with power contact. One Alarm remote dry contact One Set point Measure dry contact. On/OFF, Timed, Proportional routine function setting. ORP Conductivity Chlorine (Amperometric Cell) Chlorine and Chlo. Dioxide
(Potentiostatic Cell)
014,00 pH 2000 mV 1200/102000/10020.000 S 05,00 ppm (*) 00,50 /1,00 /2,00 /5,00 /10,0 /20,0 /200,0 ppm
with PT100/PT1000 0100C (32212 F)
Temperature
(*): Amperometric Chlorine CU+PT sensors
Product line
Code

Description for Amperometric Chlorine values for Free and Total Potentiostatic Chlorine values
Model Kontrol CL 800 Kontrol CLP 800
K800L01 K800L06
Product line
K800L02 K800L03 K800L04 K800L05 K800L07 K800L08 K800L09

for pH/ORP - pH/ORP values for pH/Amperometric Chlorine values for pH/ORP - Amperometric Chlorine values for pH/ORP - Conductivity values for pH + Potentiostatic Chlorine values for pH /ORP + Potentiostatic Chlorine values for pH/ORP + Pot. and Amperometric Chlorine values
Kontrol PR 800 Kontrol PC 800 Kontrol PRC 800 Kontrol PR+EC 800 Kontrol PCP 800 Kontrol PRCP 800 Kontrol PRCP+CA 800
innovation
07
Photometer System
Photometer Light
Photometer System Photometer System

Parameters
l pH / ORP l Free and Total Chlorine l Combined Chlorine by software
Multi parameter photometer instrument
The Seko Photometer System is a DPD reference point for Chlorine control. The combination of water sampling and reagents ensure maximum measurement precision. The unit itself is a compact miniature analysis laboratory dedicated to Chlorine measurement.
Features
The unit has the following innovative features: New hydraulic device with water drain dedicated to chemical reagents used for chlorine measure. Therefore it allows to reduce the water amount used for chlorine measure. The water dedicated to pH and Redox probes it may be to restored in the compensating basin, while only the water with chemical DPD reagent will be discharged in special tank to observes the local law. Fast installation thanks to quick coupling for Inlet and Outlet water. Optical unit assure a High accuracy Chlorine measure with a 520 nm sensor and LED light device. Moreover: The Peristaltic pump with 4 mechanical support assure chemical reagent saving. Reagent level controlled by level probes. The chemical powder to dilute before the use is a good solution safety to keep it ready in every place. Graphic display and Keypad LCD STN 240x128 backlighted (Photometer System) LCD STN 128x64 backlighted (Photometer Light) Visualisation of: measurements (simultaneous up to 4 values + trend line), digital outputs condition, storage condition, malfunctions. Using keypad with 4 embossed keys.
Applications
l Waste Water l Drinking Water l Boiler l Legionella disinfection l Crate Wash l Dioxide Station l Irrigation l Swimming Pool l Sea water
08 seko
Measure range
Internal data logger 4 Mbit flash memory equal to 16000 records Recording interval 00:00 to 99:99 min Type: circular / fill Display: table / graph (1 for each parameter). Analogue outputs 1 for each measured parameter (excluding comb. chlorine) Type: 0.00 / 4.00 to 20.00 mA Galvanically isolated Programming limit: lower / upper / reverse Maximum load: 500 Ohms - Alarm output NAMUR compliant 2.4 mA (with 420 mA range) PID control function can be activated on the pH output Set point relay outputs Two (2) for Primary measure + for pH measurement (only mod. 4001-3) Programming for Hysteresis, working time and Daily hourly activation not subject to the measured value: - ON - OFF - 00.00 to 05:00 ppm Cl 2 - 00:00 to 14.00 pH Working time: 000 to 999 sec. Relays 5A resistive load up to 230 Vac Alarm Relay Output Two (2) for Primary measure + Two (2) for pH measurement (only mod. 4001-3) Programming for Hysteresis, working time and Daily hourly activation not subject to the measured value: - ON - OFF - 00.00 to 05:00 ppm Cl 2 - 00:00 to 14.00 pH Working time: 000 to 999 sec. Relays 3A resistive load up to 230Vac
Code pH ORP Chlorine (Photometric chamber) Temperature

(*): DPD Method
Description 014,00 pH 1500 mV 05,00 ppm (*)

with PT100/PT1000 0100C (32212 F)
Product line
Code SPL3CL Model
Photometer Light Multi parameters
Description
Free Chlorine, pH and Redox
Photometer
Product line
Code SPT2CL SPT2CT Model
Photometer System Single parameter
Description
Free Chlorine Total Chlorine
Photometer Photometer
Product line
SPT3CL(*) SPT4CL SPT5CL
Photometer System Multi parameters

Free Chlorine and pH Free Chlorine, pH and Redox Free, Total and Combined Chlorine, pH, Redox
Photometer Photometer Photometer
(*): Sea water application on demand code SPT3CLMW0001
innovation
09
Kontrol 40-42
Parameters
Single and multiple-parameter control instruments
The Kontrol 40 and 42 are single and multiple-parameter controllers respectively. These very user-friendly systems combine advanced performance and simple design. Single-parameter units are available in four different casings, ensuring perfect fit at the right price.
Features
Graphic display and Keypad Simultaneous value of the measure, Temperature and Relay status. 2-line, 16 character Aplhanumeric Display. Four control keys for instrument calibration and configuration. Enclosure Box and Power Supply Four (4) mechanical box: Wall mounting PP (IP65) Panel mouting: 96x96 IP65 Front panel 48x96 IP40 Din-Rail (6 modules) IP40 Universal Power Supply 100240 Vac 50/60 Hz and 24Vac/dc
Kontrol 40-42
10 seko
l pH / ORP l Conductivity l Chlorine l Chlorine Dioxide l Flow Rate
Applications
l Waste Water l Drinking Water l Cooling Towers l Boiler l Legionella disinfection l Reverse Osmosis l Crate Wash l Galvanic Process l Dioxide Station l CIP l Irrigation l Swimming Pool l Sea water
Measure range
Code pH
Manual controls The user-friendly programming step menu makes starting up and checking the control and dosing system easy. Measure Input High measuring resolution with probe quality control. Modular measuring system Chlorine measure in sea water application Digital Input Voltage Input to disable all function controller output. Current outputs 420mA Galvanic isolation One(1) programmable measurement output. Relay Outputs Two (2) independent function, two Set point Measure, dry contact. Software-set alarm functions. Routine function settings : ON/OFF, Timed or proportional
Description 014,00 pH 1500 mV 1200/102000/10020000/20050000 S 05,00 ppm 00,50 /1,00 /2,00 /5,00 /10,0 /20,0 /200,0 ppm
with PT100 0100C (32212 F)
ORP Conductivity Chlorine (Amperometric Cell) Chlorine and Chlo. Dioxide

(Potentiostatic Cell)
Temperature Flow Rate
99 999,99 Liters/second (*)
(*) Setting by software following unit measures: l/s, l/h, m/h, GPM.
Product line
Code SPR040 SCD040 SCL040 SFX040
Model
Kontrol 40 Kontrol 40 Kontrol 40 Kontrol 40
Description
for pH/ORP values for Conductivity value for Potentiostatic Chlorine value for Flow Rate value
Product line
K042PR K042PD K042PC K042CF K042PF K042DF

for pH/ORP and pH/ORP values for pH/ORP and Conductivity values for pH/ORP and Chlorine values for Chlorine and Flow Rate values for pH/ORP and Flow Rate values for Conductivity and Flow Rate values
Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42
innovation
11
Kontrol 20-22
Parameters
Single or multi-parameter control instruments
The Kontrol 20 and 22 are simplified, bare-bones single and multiple-parameter controllers respectively. These trustworthy systems combine reliable high-end performance and simple design. Single-parameter units are available in four different casings, ensuring perfect fit at the right price.
Features
Graphic display and Keypad 2-line, 16 character Aplhanumeric Display. Four control keys for instrument calibration and configuration.
Kontrol 20 - 22
l pH / ORP l Conductivity
Applications
l Waste Water l Drinking Water l Cooling Towers l Boiler l Reverse Osmosis l Galvanic Process l Irrigation l Swimming Pool
Enclosure Box and Power Supply Four (4) mechanical box: Wall mounting PP (IP65) Panel mouting: 96x96 IP65 Front panel 48x96 IP40 Din-Rail (6 modules) IP40 Universal Power Supply 100240 Vac 50/60 Hz
12 seko
Measure range
Code pH
Measure Input High measuring resolution with probe quality control. Digital Input Voltage Input to disable all function controller output. Current outputs 420mA One (1) programmable measure output. Relay Outputs Two (2) independet functions, Set Point Measure, dry contact. Software to set alarm functions. ON/OFF routine function settings.
Description 014,00 pH 1500 mV 1200/102000/10020000 S

with PT100 0100C (32212 F)
ORP Conductivity Temperature
Product line
Code SPR020 SCD020 Model
Description
for pH/Redox values for Conductivity value
Kontrol 20 Kontrol 20
Product line
K022PR

for pH and Redox values
Kontrol 22
innovation
13
pH/Redox Probes
SPH-3 WW SRH-3 PT
Field Application: Waste water Drinking Water Cooling Towers Legionella disinfection Galvanic Process
SPH-1 / SRH-1
Field Application: General laboratory Drinking Water Swimming pools Water monitoring and control plan
SPH-2
Field Application: Waste water Drinking Water Cooling Towers Irrigation
Features:
Low maintenance sealed unit Gel filled reference cell BNC connection with Boot plastic Cover Cable length 6 or 1,5 meter Pellon Diaphragm high accuracy
Features:
Low maintenance sealed unit Gel filled reference cell S7 connection Pellon Diaphragm high accuracy
Features:
Low maintenance sealed unit Gel filled reference cell S8 connection with PG 13,5 mm Glass Body Diaphragm open hole
SPH-4 HP
Field Application: Waste water Drinking Water Reverse Osmosis Cleaning in place (CIP) Galvanic Process
SPH-4 HT SRH-4 HT-PT

Field Application: Ammonia application Chromium plating Reverse Osmosis Bisulphite application Galvanic Process
SPH-4 LC
Field Application: Highly acidic solutions Chromium plating Reverse Osmosis Bisulphite application Galvanic Process
Features:
Low maintenance sealed unit Gel filled reference cell S8 connection with PG 13,5 mm Glass Body for High Temperature Enviromental Diaphragm 2 Sigle pore
Features:
Low maintenance sealed unit Gel filled reference cell S8 connection with PG 13,5 mm Glass Body for High Pressure Enviromental Three ceramic diaphragm type
Features:
Low maintenance sealed unit Gel filled reference cell by External Refill S7 connection with PG 13,5 mm plastic nut Glass Body for low pressure Enviromental Highly acidic solutions One Sleeve diaphragm type
14 seko
Measure range
Measurement range Temperature range Min. conductivity Mechanical mounting Diaphragm type Electrical connection Reference electrolyte Membrane material
Pressure range
Body material
SPH-1 1.5M
212 50 S/cm
Code 9900105001
pH
Epoxy Glass GEL 1 Ceramic 1,5m cable + BNC Standard 12
060C
04 bar
SPH-1 6M
212 50 S/cm
Code 9900105002
pH
Epoxy Glass GEL 1 Standard 6m cable + BNC Standard 12
060C
06 bar
SPH-2
212 50 S/cm
Code 9900105003
pH
Epoxy Glass GEL 1 Standard S7 PG 13.5
060C
06 bar
SPH-3 WW
212 5 S/cm
Code 9900105005
pH
Glass Glass GEL 1 Open hole S8 PG 13.5
080C
06 bar
SPH-4 HP
014 5 S/cm
Code 9900105006
pH
Glass Glass GEL 2 Single Pore S8 PG 13.5
0130C
06 bar
SPH-4 HT
014 5 S/cm
Code 9900105007 0130C at 6 bar 016 bar at 25C
pH
Glass Glass GEL 3 Ceramic S8 PG 13.5
SPH-4 LC
014 0.2 S/cm
Code 9900105008
pH
Glass Glass GEL 1 Sleeve S7 PG 13.5
-1040C
0,5 bar
SRH-1-1.5M
1000 mV -
Code 9900105031
Redox
Epoxy
Platinum wire
060C
04 bar
GEL
1 Ceramic
1,5m cable + BNC
Standard 12
SRH-1- 6M
1000 mV -
Code 9900105032
Redox
Epoxy Platinum wire GEL 1 Standard 6m cable + BNC Standard 12
060C
06 bar
SRH-3 PT
2000 mV -
Code 9900105033
Redox
Glass Platinum wire GEL 1 Open hole S8 PG 13.5
080C
06 bar
SRH-4 HT - PT
2000 mV -
Code 9900105034 0130C at 6 bar 016 bar at 25C
Redox
Glass Platinum wire GEL 3 Ceramic S8 PG 13.5
SRH-1 6M - AU
2000 mV -
Code 9900105083
Redox
Epoxy Gold GEL 1 standard 6m cable + BNC Standard 12
060C
06 bar
* S7 connection: it is a electrical connection only ** S8 connection: S7 on the top electrical probe connection and PG 13.5 mm mechanical connection
innovation
pH/Redox Probes
15
Conductivity Probes
The seko range of conductivity probes is specially designed for use in industrial environments in conjunction with seko measurement instruments. The various available models make it possible to cover an extremely wide measurement range. There are versions with temperature sensors and special versions with graphite or platinum probes, PTFE cell bodies and IP67 connectors. Measurement of conductivity is performed by suspending the two metallic electrodes of the probe in the solution to be measured. The passage of the current between the two electrodes indicates the electrical resistance of the liquid, and therefore its conductivity. The measurement is influenced by the temperature. In saline solutions, measurement variations of 2% / C can occur. This variation can even reach 7% / C. Therefore, conductivity probes without temperature sensors should only be used if the solution being tested is maintained at a temperature between 15C and 25 C, restricting the potential for error to 10%. Note All the models are guaranteed for a maximum pressure of 6 bars.
C-K1 PT
Field Application: - Waste Water - Drinking Water - Cooling Towers - Boiler - Reverse Osmosis - CIP - Irrigation - Fish Farming - Dairy Features: l Costant Cell: 1 cm or K=1 l Body material: Glass (130C ) l Electrodes material: Platinum l Mechanical Connection: 12 mm Features:
CT-K5
Field Application: - Waste Water - Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation
l Costant Cell: 0,1 cm or K=10 l Body material: PP (80C) l Electrodes material: Stainless steel 316L l Mechanical Connection: Gas M PP
Without temperature sensor
With temperature sensor (PT100)
C-K10/5 /1
CT-K10
Field Application: - Waste Water
CT-K1
Field Application: - Waste Water - Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation Features: l Costant Cell: 0,1 cm or K=10 l Body material PP (80C) l Electrodes material: Stainless steel 316L l Mechanical Connection: Gas M PP
Field Application: Waste Water Drinking Water Cooling Towers Irrigation Features: l Costant Cell: - 0,1 cm or K=10 - 0,2 cm or K=5 - 1,0 cm or K=1 l Body material: PVC (60C ) l Electrodes material: Stainless steel 316L l Mechanical Connection: Gas M Pvc Features:
- Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation
l Costant Cell: 0,1 cm or K=10 l Body materia:l PP (80C) l Electrodes material: Stainless steel 316L l Mechanical Connection : Gas M PP
Without temperature sensor
16 seko
Measure range
Measurement range Temperature range Mounting Process
Constant [C-K]
Pressure range
Body material
C-K10
0,01500S
Code 9900101012
Without temperature
60C 6(*) PP-AISI 316 1/2 G.M. 5m
C=0,1 cm-1 K=10cm

Code 9900101011
C-K5
0,11000S
Without temperature
60C 6(*) PP-AISI 316 1/2 G.M. 5m
C=0,2 cm-1 K=5cm

Code 9900101010
C-K1
15000S
Without temperature
60C 6(*) PP-AISI 316 1/2 G.M. 5m
C=1 cm-1 K=1cm

Code 9900101013
C-K1-PT
120000S
Without temperature
120C 6(*) Glass - Platinum 12 mm 6m
C=1 cm-1 K=1cm

Code 9900101103
CT-K10
0,01500S
(PT100) With temperature

80C 6(*) PP-AISI 316 3/4 G.M. Plug (**)
C=0,1 cm-1 K=10cm

Code 9900101102
CT-K5
0,52000S

80C 6(*) PP-AISI 316 3/4 G.M.
C=0,2 cm-1 K=5cm

Code 9900101101
Plug (**)
CT-K1
55000S

80C 6(*) PP-AISI 316 3/4 G.M.
C=1 cm-1 K=1cm
Plug (**)
Conductivity Probes
(*) The maximum pressure of 6 bars is guaranteed at 25 C. As the temperature increases, the pressure decreases linearly and at 50 or 80 C, the maximum pressure is 1 bar. (**) To be used in conjunction with CC series cables.
innovation
Cable
17
Conductivity Probes
CT-K1 G
Field Application: - Waste Water - Drinking Water - Cooling Towers - Reverse Osmosis - CIP - Irrigation - Fish Farming Field Application: - Waste Water - Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation Field Application: - Waste Water - Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation
CT-K1-SS
CT-K1-GR
Features: l Costant Cell: 1 cm or K=1 l Body material: PVC (60C ) l Electrodes material: Graphite l Mechanical Connection: 12 mm
Features: l Costant Cell: 1 cm or K=1 l Body material: PVDF (80C) l Electrodes material: Stainless steel 316L l Mechanical Connection: Gas M PP
Features: l Costant Cell: 1 cm or K=1 l Body materia:l PVC (60C) l Electrodes material: Graphite l Mechanical Connection: Gas M PVC
Measure range
Measurement range Temperature range Mounting Process Constant [C-K] Pressure range Body material
CT-K1-G
520000S
Code 9900101124

60C 6(*) PVC Graphite PG 13,5 mm 7m
C=1 cm-1 K=1cm

Code 9900316009 (5m)
CT-K1-SS
120000S
9900316010 (10m)
100C

6(*) PTFE 1 G.M. 5 m or 10 m
C=1 cm-1 K=1cm

Code 9900316028 (5m)
CT-K1-GR
120000S
9900316029 (10m)
50C

6(*) PVC 1/2" G.M. 5 m or 10 m
C=1 cm-1 K=1cm
(*) The maximum pressure of 6 bars is guaranteed at 25 C. As the temperature increases, the pressure decreases linearly and at 50 or 80 C, the maximum pressure is 1 bar.
Conductivity Probes
18 seko
Cable
Inductive Probes
Inductive Probes
The S411/IND series of inductive sensors has been engineered and developed to produce an electrode that is very powerful but at the same time competitive. The result has been obtained by moulding the sensor made using polypropylene reinforced with fibreglass. This sensor offers all the advantages of the inductive cond. measurement method, including the absence of passivation of the conventional conductivity electrodes. All the sensors in the S411/IND range are temperaturecompensated, and are also designed for inline, submersion or tank installation.
S411/IND
S411/IND/E
S411/IND/T IN
Measure range
Inductive Probes Temperature Contact materials Temp. compensation Cable Connection Protection rating Materials Operating temperature Submersion length Assembly Operating pressure Conductivity Range Resolution
Inductive Probes
SENSOR S411/IND
-5 to 60 C (without freezing) Glass-reinforced polypropylene PT1000 wires Standard 5 metre " BSP male IP67 PVC with Viton gaskets -5 to 60 C (without freezing) 600 or 1200 mm Standard bracket or optional flange From vacuum to 6.5 bar (100 psi) 1000 S to 1 Simens 100 S to 1000 S
Code 6100011441
S411/IND/T
Inductive Probes
innovation
19
Dissolved Oxigen Probes

OXYSENS
The OXYSENS is an electrochemical oxygen sensor designed for applications in water, e.g. waste water treatment, swimming pools or fish farms. It is easy to maintain, because the membrane and the electrolyte dont need to be replaced. The response time of the OXYSENS is fast, it is almost independent of flow and insensitive to soiling.
S423/C OPT
The S423/C OPT sensor with an integrated temperature sensor is based on luminescent optical technology. Without calibration requirements and thanks to an ultra low power technology, the S423/C OPT sensor meets the demands of field works and short or long term campaigns. Without oxygen consumption, this technology allows you an accurate measure in all situation and especially in very low oxygen concentrations. The S423/C OPT sensor stores calibration and history data within the sensor. This allows you a plug and play system without recalibration. Thanks to the Universal Modbus RS485 protocol, The S423/C OPT sensor can be connected to all devices commonly used (Datalogger, Controller, Automat, Remote System).
Flow Sensor
SFW
The paddlewheel flow sensor SFW is designed to be used with every kind of solid-free liquid. The sensor can measure flow from 0.15 m/s (0.5 ft/s) producing a frequency output signal highly repeatable. A new electronic, with a pushpull output, is now available for a safe connection to any kind of PLC/instrument digital input. A special family of fittings ensures installation into all pipe material in sizes from DN15 to DN600 (0.5" to 24").
SFWE
The SFWE insertion magmeters can measure flow rate in both metal and plastic pipes. No moving parts allow the measurement of liquids with suspended solids as long as conductive and homogeneous. The sensors can be assembled into the standard FLS fittings for installation from DN15 to DN600 (0.5" to 24"). They offer frequency output to use with FLS flow instrumentation and 4-20 mA output for long distance transmission and PLC connection. Special versions for salt-water applications (high concentration of chlorides as sea water) and for high temperature conditions.
Flow Sensor
20 seko
Flow Sensor
Measure range Dissolved Oxigen Probes

Dissolved Oxigen Probes Measuring method Measurement range Accuracy Response time Required flow Temperature sensor Storage temperature Temperature range Pressure range Body material Membrane material Reference electrolyte Electrical connection Mechanical mounting Measuring method Signal interface Polarization voltage Application fields OXYSENS
Measurement of the electrical current affected by the partial pressure of oxygen
S423/C OPT (35mm)

Optical measure by luminescence
0,00 to 20,00 mg/L / 0,00 to 20,00 ppm / 0-200% [Resolution 0,01]
40ppb40ppm < 0.5% [relative to current in air] 98% Max. 60 s at 25 C 0.03 m/s NTC 22 kOhm -1060C 060C 04 Bar Stainless steel 1.4435, silicone, EPDM OPTIFLOW Silver platinum combination 5 m cable PG 13.5
Measurement of the electrical current affected by the partial pressure of oxygen -
0,1mg/L / 0,1 ppm / 1% 90% of the value in less than 60 seconds No necessary move CTN -1060C 050C 05 Bar Stainless Steel INOX 316L No membrane No electrolyte 10 m cable 35mm
Optical measure by luminescence Modbus RS-485 (standard) and SDI-12 (option)
-670 50 mV
Water applications: Waste water treatment, swimming pools, fish farms; composting facilities
Code 9900316005
5 to 12 volts
Urban wastewater treatment, industrial effluent treatment, surface water monitoring, drinking water
Code 9900105091 35mm
Measure range
Flow Sensor Working range Minimum reynolds Linearity Repeatability Maximum process Pressure/Temperature Materials
Flow Sensor
SFW 0.15 to 8m/s [0.5 to 25ft/s] 4500 0.75% of full scale 0.5% of full scale PVC-Cbody: 10 bar - 25C 1.5 bar - 80C
Sensor body: CPVC or PVDF or 316L SS
SFWE 0.15 to 8m/s [0.5 to 25ft/s]

-
1% of reading +1.0 cm/s 0.5% of reading

Brass&SSbody:
PVDFbody:
10 bar - 25C 1.5 bar - 100C

Rotor: ECTFE (Halar)
25 bar - 120C 25 bar - 100C

Bearings: Ceramic (Al2O3) Sensorbody: 316L SS PVDF
16 bar - 25C 8.6 bar - 70C

O-rings: EPDM or FPM Electrodes: 316L SS
O-rings: EPDM or FPM
Shaft: Ceramic (Al2O3)
Outputs Power supply Application fields
Square wave, frequency: 45 Hz per m/s [13.7 Hz per ft/s] nominal
420 mA with K330 output kit mounted
420 mA - Isolated Square wave, frequency: 0-500Hz Open collector: flow direction
5 to 24 VDC 10% regulated

Water and industrial waste water treatment, water distribution, processing and manufacturing industry, textile finishing, chemical production, cooling and Heating systems, swimming pools and Spas. Code 990031701X PVC SFW1 / SFW2 Code 990031704X Stainless Steel SFW1 / SFW2
12 to 24 VDC 10% regulated (reverse polarity and short circuit protected)

Water and waste water treatment, raw water intake, industrial water distribution, textile industry, swimming pools, Spas and aquariums, HVAC, processing and manufacturing industry. Code 9900317040 Mag SFW1 Code 9900317041 Mag SFW2
innovation
21
Potentiostatic Probes CLPROBES

This range consists of potentiostatic amperometric probes to measure free or total chlorine for applications such as: water treatment, swimming pools, industrial applications and more. The wide range of probes allows a better choice depending on the parameter to be tested, thus obtaining a more accurate measurement. l The two-wire interface allows quick and easy installation.
High pressure Probe sensors
Measure range
Models
Measure range pH range Response time Flow rate Temperature Pressure Sensor material Membrane M20 1 bar 30 L/h 45 C 0,5 bar Silver chlorine with gold M48 M48 G ECS1 Gel M20 M20 50 C 5 bar (*) Gold 48 pH
F-CL 1
F-CL 2
010 ppm 412 pH
F-CL 3
F-CL 4
0200 ppm
F-CL 5
02 ppm
F-CL 6
01 ppm
F-CL 7
05 ppm
F-CL 8
01 ppm
F-CL 9
05 ppm
Potentiostatic Probes
F-CL 10
00,5 ppm 48 pH
l Calibration of the probe is guided by the Kontrol CL500 instrument .
F-CL 11
05 ppm 48 pH
411 pH
48 pH
59 pH
1 minutes - 90% of measure (100% of measure after 15 minutes) 80 L/h 70 C 8 bar (*) 0,5 bar 30 L/h 45 C 1 bar
Silver chlorine with gold M20 M20
ECL1 Electrolyte Electrical connection Mechanical mounting Application fields Inorganic Free Chlorine Code
ECC1
ECL1
ECL1 EAS1 Gel
ECL1
ECL1
Wire connection with screw 24mm Organic Free Chlorine Code Code Code Code Inorganic Free Chlorine Code Code Code Code Code Code
9900101140 9900101141 9900101142 9900101146 9900101148 9900101149 9900101150 9900101152 9900101153 9900101159 9900101173
(*) with Snap-Ring F-CL 2 F-CL 3 T-CL 1 can be used in sea water application with special electrolites
22 seko
and Modular probe holder
PSS-PLEXI Features
l In/Out: 8x12 mm (tube) l Material Plexiglas without color l Hydraulic - By Pass l Pressure 5 bar l Temperature 60C
CL Probes Holder
Code 9900103047 PSS-PLEXI [FLUX/PH] Code 9900103048 PSS-PLEXI [FLUX/PH/RX] Code 9900103049 PSS-PLEXI [FLUX/CL-A] Code 9900103050 Code 9900103051 Code 9900103052 Code 9900103053 Code 9900103054 Code 9900103055 Code 9900103056
PSS-PLEXI [FLUX/PH/CL-A] PSS-PLEXI [FLUX/PH/RX/CL-A] PSS-PLEXI [FLUX/PH/CL-P] PSS-PLEXI [FLUX/CL-P] PSS-PLEXI [FLUX/PH/RX/CL-P] PSS-PLEXI [FLUX/PH/RX/CL-A/CL-P] PSS-PLEXI [FLUX/CL-P/CL-P]
F-CL12
F-CL13
T-CL 1
010 ppm
T-CL 2
05 ppm
D-CL
010 ppm 114 pH
D-CL 2
D-CL 3
PAA 1
02000 ppm
H202 1
0200 ppm 211 pH
H202 2
0500 ppm
03 1
02 ppm
03 2
05 ppm
BR 1
0.0510 ppm 6.59.5 pH
02 ppm 412 pH 411 pH
01 ppm 59 pH
414 pH
114 pH
1 minutes - 90% of measure (100% of measure after 15 minutes) 30 L/h 45 C 0,5 bar Silver chlorine with gold M48 M48 G ECS1 Gel M48 M48 M20 1 bar 50 C 5 bar (*) 80 L/h 70 C 8 bar (*) 1 bar 1 bar 30 L/h 45 C 1 bar 0,5 bar
Gold M7N
Silver chlorine with gold M20 M20 M48
ECC1
ECP1 Gel
ECP1 Gel
EDC41 EAS1 Gel EPS7/W EOZ1
EBR1 Gel
Wire connection with screw 24mm Organic Free Chlorine Code Inorganic Free Chlorine Code Total Chlorine Code Code Code Chlorine Dioxide Code Code Peracetic Acid Code Hydrogen Peroxide Code Code Code Ozone Code Bromine Code
9900101174 9900101177 9900101143 9900101172 9900101144 9900101151 9900101154 9900101157 9900101158 9900101156 9900101175 9900101176 9900101179
Potentiostatic Chlorine Probes

innovation
23
Turbidimetric Probes
and Suspended Solid probes
The principle of measurement is the deviation of light produced by suspended particles in the liquid. Thanks to the dual sensor is possible to make measurements of turbidity at low and very low concentrations with high accuracy and repeatability. Avoiding contact with the measuring liquid, the optical LED technology make the system stable over time and minimize the need for recalibration. The cell is installed directly in line, the maximum allowable pressure is 4 or 6 bar, pipe or bypass. The flow velocity does not affect the measurement.
S462/SS
Field Application: Sewage Treatment Drinking Water Waste water Cleaning in place
Turbidimetric probes
Features:
SS AISI 316 material
Features and Benefits

Reliable concentration measurement using optical measuring process Infrared light pulsing beams scattering method Black rigid PVC sensor body No mechanically moving parts Measured value pre-processing in sensor resulting in low signal transmission sensitivity
Solid Measure with Led light with Resistors sensor

Threaded Connection 2 1/2" M GAS Two cables included
Resistors sensor
Threaded Connection 1" GAS Cables included
S461/T
Field Application: Sewage Treatment Sludge application Waste water Fish farming
Features: SS AISI 316 material Turbidity Measure with Led light with Resistors sensor Threaded Connection 1" GAS Cables included
Resistors sensor
Threaded Connection 1" GAS Cables included
S462/PVC/SWP
Field Application: Waste water Drinking Water Swimming pool Sewage Treatment
S461/S
Suspended Solids probes
Features: SS AISI 316 material Solid Measure with Led light with Resistors sensor Threaded Connection 1" GAS Cables included Field Application: Sewage Treatment Sludge application Waste water
Features: Black Plastic Body Turbidity Measure with Led light with
Resistors sensor Threaded Connection 2 1/2" F GAS Two cables included
Resistors sensor Threaded Connection 1" GAS Cables included
24 seko
Measure range
Measurement range Measurement method Temperature range Applications field
- Water treatment plants , downstream of filtration and decantation. Process section; - Aging facilities of wastewater reuse for agricultural or industrial purposes; - Food industry particularly in the production of beverages, wine, beer etc.; - Pool water. Wastewater, primary water, industrial water, recirculating water. Pool water Wastewater, primary water, industrial water, recirculating water.
Electrical connection
2 cables 5m 5m cable 10m cable 2 cables 5m
S462/PVC
Code 9900316021
Tu r b i d i m e t r i c
PVC black Transparent PVC door
0,00100 Scattering at 180 NTU/FTU Light absorption
045 C
06 bar
1224 Vdc
S462/SS
Code 9900316006
Stainless Steel INOX 316 Tempered glass window
0,00100 Scattering at 180 NTU/FTU Light absorption
090 C
06 bar
1224 Vdc
S461/T
0,00/4 /40 /400 /4000
Code 9900316022
Stainless Steel INOX 316 Special Optical Glass or Viton
Scattering at 90 Light absorption
060 C
04 bar
1224 Vdc
1GAS
S462/SWP
0,0040 NTU/FTU
Code 9900316024
PVC black Transparent PVC door
045 C
06 bar
1224 Vdc
Turbidimetric Probes
Measure range
Measurement range Measurement range Temperature range Applications field Electrical connection
10m cable
S461/S
20 gr/l
Code 9900316025
Sospended Solid
Stainless Steel INOX 316 Special Optical Glass or Viton
060 C
04 bar
1224 Vdc
1GAS
Sospended Solid Probes
Threaded connection
Pressure range
Body material
Power supply
Threaded connection
2F 2M 2F
Pressure range
Body material
Power supply
innovation
25
Suspended Solid Probes
Suspended SolidProbe
The 7520 SAV and 7540 SRH sensors are used for optical solids content measurement in turbid water for up to 150g solid matter/l.
7520 SAV-T/E
Applications
l Solids content measurement of suspended matter in sewage treatment plants: Primary sludge, digested sludge, thickened sludge, Inflow to centrifuge / press. l Industrial quality control.
Features and Benefits

Reliable concentration measurement using optical measuring process. Infrared light pulsing beams scattering method. Black rigid PVC sensor body. No mechanically moving parts. Measured value pre-processing in sensor resulting in low signal transmission sensitivity.
7540 SRH-T/E
26 seko
Measure range
Suspended Solid Probes Mechanical data
Dimension (Lx) Immersion type Dimension (Lx) Installation type Weight Immersion type Weight Installation type
7520 SAV-T/E
139 x 38 mm 220 x 38 mm Approx. 1Kg Approx. 3Kg Stainless steel SS 316 Ti Epoxy resin
7540 SRH-T/E
134 x 38 mm 220 x 38 mm Approx. 1Kg Approx. 3Kg Stainless steel SS 316 Ti Epoxy resin Viton Backscatter light method
Light source 2 LEDs detectors 2 photodiodes Infrared light at 880 mm absorption maximum 10150g solid matter/l, dependent on sludge type
Materials
Sensor Body Sight glass O-rings
Viton
Light absorption method
Light source 2 LEDs detectors 2 photodiodes Infrared light at 880 mm absorption maximum 050g solid matter/l, dependent on sludge type
Measurement range
Measuring principle Optical components Measuring light Measuring range Accuracy Reference Cable lengths Calibration
< 1% of measuring range end value Using four-beam pulsed light method
T version 13m E version 1m + 10m extension cable
< 1% of measuring range end value Using four-beam pulsed light method
T version 13m E version 1m + 10m extension cable
With silica standard 0150C max 6 bar IP 68
With silica standard 0150C max 6 bar IP 68
Operating conditions
Op. temperature Op. pressure Protection
On demand
On demand
Suspended Solid Probes
innovation
27
Cables, buffer solutions and probe accessories
Immersion probe holders
Probe Accessories
PI
No. of probes
Immersion probe holder
Sensors for measuring pH, Redox and Conductivity must be installed in the system using special probe holders that ensure the correct mechanical protection and degree of impermeability. The pH and Redox measurement probes can be submerged in tanks, inserted in pipes or placed in sample draw down containers (Catch Pots).
The immersion models with adjustable flange can be used in conjunction with a counter-flange which allows quick and easy installation and removal. The P-IG range with a floating platform adapts to the varying liquid level of deep water tanks. The polypropylene versions PIR-2-PPxxx can house two sensors, e.g. pH and Redox. It is not recommended to use PH and/or Redox sensor in the same probe holder as a conductivity cell.
Max Temperature
40C 40C 40C 40C 40C
Immersion
PI PVC 400
400 mm
Code 9900100111
PVC
PI PVC 800
800 mm
Code 9900100112
PVC
PI PVC 1000
1000 mm
Code 9900100115
PVC
PI PVC 1500
1500 mm
Code 9900100113
PVC
PI PVC 2000
2000 mm
Code 9900100116
PVC
No. of probes
Max Temperature
40C 40C 40C 40C 40C
Immersion
PIR PVC
PIR PVC 200

100250 mm
Code 9900100101
PVC
PIR PVC 400

100450 mm
Code 9900100102
PVC
PIR PVC 800

100850 mm
Code 9900100103
PVC
PIR PVC 1000

1001050 mm
Code 9900100105
PVC
PIR PVC 1500

1001550 mm
Code 9900100106
PVC
28 seko
Material
Material
Probe Accessories
No. of probes
Max Temperature
Immersion
PIR 2 PP
PIR 2 PP 400
100450 mm
Code 9900100121
80C
PIR 2 PP 800
Code 9900100122
No. of probes
1001050 mm
80C
PP
PI G
Floating
Code 9900100131
40C
PVC
B PI G
2m anchorage arm
Code 9900100132
40C
PVC
No. of probes
Max Temperature
Immersion
PCIR PP
FER
Material
PICIR PP 400
100450 mm
Code 9900100141
for quick removal

PP
80C
Ext. Diameter
Int. Diameter
Max Temperature
PICIR PP 800
Code 9900100142
Connection
4 holes 6 mm
100850 mm
80C
PP
PICIR PP 1000
1001050 mm
Code 9900100144
Counter-flange
80C
PP
FER
65 mm
Code 9900100133
PICIR PP 1500
1001550 mm
Code 9900100145
140 mm
40C
80C
PP
Probe holders with 3/4 probe attachment without protection

These can house conductivity probes with threaded 3/4 G. Attachment with output cable or IP67 connector.
innovation
29
Material
PP
Material
PIR 2 PP 1000
Code 9900100124
Max Temperature
100850 mm
80C
Material
PI G
PP
PP
Immersion
Accessories
Probe Accessories
1/h Min - Max
Max Pressure
No. of probes
Max Temperature
Immersion
PIA PVC
Immersion probe holders with spray cleaning

These special probe holders can be connected with a cleaning liquid injection unit. Regular cleaning of the probe ensures linearity and stability of the measurement over time, preventing the need for timeconsuming manual intervention.
Back wash probe holder
PIA PVC 400

400 mm
Code 9900100151
40C
26
100600
PIA PVC 800

800 mm
Code 9900100152
40C
26
100600
PSS 7 Single
PSS 7A
PSS 7
Connection to the process
Max Pressure
Max Temperature
No. o probes
Tap probe holders

Tap probe holders are used for inline measurements where part of the sample is re-directed from the main pipe to the probe holder. The water can be drawn off into the sampling circuit at a pressure of 6 bars.
PSS 7 Single
Code 9900103021
By-Pass probe holder
By-pass
40C
6 bar
PSS 7
By-pass
Code 9900103008
40C
6 bar
PSS 7A
By-pass
Code 9900103010
40C
6 bar
30 seko
Probe Accessories
PSS-EC
Outflow probe holders for conductivity probes

Outflow probe holder
Bypass probe holder for conductivity probe model CTK1, 5 and 10 Made of black PVC with 3/4 mechanical connection and 1 GAS IN/OUT hydraulics.
OUTFLOW SECTION (PSS-COND-T)

Code 0000126035
PSS 3
SPP
SPP FIL
Connection to the process
Max Pressure
Max Temperature
Mechanical Connection
Material
Pressurized probe holder
Pressurized probe holders

Pressurised probe holders are used to immerse the probe directly into the pipe where the sample to be measured passes. The probe must always be positioned vertically or slanting in the direction of the flow at a maximum of 45. The probe holder connection line must be fitted between two isolation valves (input and output) in order to permit the prevention of the flow during maintenance of the probes.
PSS 3
1/2 G.M.
Code 9900106670
PG 13,5 or 12 mm
Code 9900100134
60C
7 bar
PVC
SPP
1 G.F.
PG 13,5
Code 9900100135
60C
16 bar
PP + PVC
SPP FIL
3/4 or 1 1/4 G.M.
PG 13,5
80C
16 bar
PP
innovation
31
Accessories
Probe Accessories
PT 100 NUT
PT 100V
PT 100V PG
Connection
Mechanical Connection
Material
Temperature sensor
Temperature probes
In order to correctly measure the pH in environments with variable temperatures, it is necessary to correct the response error of the probe resulting from temperature change. The measuring instrument must therefore be connected to a special temperature sensor.
PT 100 NUT
1 m 2-wire cable
Code 9900101178
3/4" GAS M
Code 9900101113
PVC
PT 100 NUT
1 m 2-wire cable
1/2 GAS M
Code 9900105061
PVC
PT 100V
5 m 3-wire cable
Standard 12
Code 9900105062
Pyrex
PT 100V PG
6 m 3-wire cable
Max Pressure 7 bar

Pyrex
PG 13,5
RNC
Electrical surge suppressor
Electrical surge suppressor
Allows the elimination of Eddy currents AISI 316 material - 12 mm.
Code 9900101134
32 seko
Probe Accessories
CE
CE 1/B
Code CE 9900108001 CEB 9900109001
Type of Cable
Length
1 mt.
Mod. RG58 5 mm
Crimping BNC Soldered BNC
CE 5/B
5 mt.
Code CE 9900108003 CEB 9900109003
Mod. RG58 5 mm
Crimping BNC Soldered BNC Crimping BNC Soldered BNC Crimping BNC Soldered BNC Crimping BNC Soldered BNC Crimping BNC Soldered BNC Crimping BNC Soldered BNC
CE 10/B
Code CE 9900108004 CEB 9900109004
CE B
10 mt.
Mod. RG58 5 mm
CE 20/B
20 mt.
Code CE 9900108006 CEB 9900109006
Mod. RG58 5 mm
CE 10 HT(*)/B
10 mt.
Code CE 9900110001 CEB 9900110101
Mod. HT 5 mm
Probe cables
Probe cables with S7 heads

(*) HT - High Quality Cable
for higher protection from electical interference.
CE 20 HT(*)/B
20 mt.
Code CE 9900110002 CEB 9900110102
Mod. HT 5 mm
CE 30 HT(*)/B
30 mt.
Code CE On demand CEB 9900110103
Mod. HT 5 mm
CC
Version Length No. poles
4 4 4
CC 5
5 mt.
Code 9900110111
standard
Code 9900110112
CC 10
Probe cables
Cables for CTK Probe

with 4-pole connectors
10 mt.
standard
Code 9900110113
CC 15
15 mt.
standard
innovation
Terminal block
33
Accessories
Probe Accessories
PE 10 /B
Type of Cable Length
PE 10/B
10 mt.
Code PE 9900108007 PEB 9900109007
Mod. RG58 5 mm
Crimping BNC Soldered BNC Crimping BNC Soldered BNC
PE 20/B
Code PE 9900108008 PEB 9900109008
Probe cables
Extension Cables for BNC-F Probe BNC-M Probe

(*) HT - High Quality Cable
for higher protection from electical interference.
20 mt.
Mod. RG58 5 mm
PE 20 HT(*)/B
20 mt.
Code PE 9900110004 PEB 9900110104
Mod. HT 5 mm
Crimping BNC Soldered BNC Crimping BNC Soldered BNC
PE 30 HT(*)/B
30 mt.
Code PE 9900110005 PEB 9900110105
Mod. HT 5 mm
ST PH ST MS
Value Quantity
250 ml 250 ml 250 ml 250 ml 500 ml 500 ml 500 ml
ST PH 4
pH
Solution
Code 9900122007
4,00 pH 20 C
Code 9900122008
ST PH 7
pH
7,00 pH 20 C
Code 9900122009
ST RX
ST PH 9
pH
9,22 pH 20 C
Code 9900122010
ST RX 465
Redox
465 mV 25 C
Code 9900122018
ST MS 8
Certified buffer solutions

Buffer solution
The precision and reliability of a pH, Redox or Conductivity measurement is determined by the buffer solution used for calibrating the probe. The special double-plug container ensures that a new unpolluted buffer is always available.
Conductivity
84 S/cm 25C
Code 9900122019
ST MS 14
Conductivity
1423 S/cm 25C

Code 9900122020
ST MS 128
Conductivity
12880 S/cm 25C
34 seko
Terminal block
Probe Accessories
Measurement
Function
ASV
Signal amplifiers
ASV pH / Redox
Code TPM032PX0000
Amplifier
Voltage
Battery
lasts 4 years
Signal amplifiers
Battery-powered live ASV signal amplifier
In order to connect a pH or Redox measurement probe at a distance of over 15 meters, it is necessary to use the ASV signal amplifier to be connected between the probe cable and the extension cable of the measurement instrument.
Dehumidifier and reduction flange for Turby Sensor
Reduction Flange
REDUCTION FLANGE
21/2 to 1/2 GAS F IN/OUT
Code 9900316011
DEHUMIDIFIER
DEHUMIDIFIER
Power supply 230 Vac 50Hz 4x6 mm hydraulic connections
Code 9900316012
innovation
Power supply
Output
35
A Worldwide Group at your service

seko is an International Group, developing, manufacturing and delivering its products in more than 50 countries, through its subsidiaries and an extended network of distributors, agents and authorized dealers. seko is a leading manufacturer of dosing pumps and dosing systems with more than 40 years experience. This long activity allowed seko to acquire a vast experience in diversified applications and to confirm its international success in many industrial fields through the supply of reliable solutions for the dosing, injection and transfer of liquids.
ITALY n Seko Spa 02010 S.Rufina - Rieti sales@seko.com BRAZIL n Seko do Brasil Commercio de Sistemas de Dosagem Limitada 03170-050 So Paulo (SP) sekobrasil@sekobrasil.com.br www.sekobrasil.com.br BENELUX n Seko Benelux B.V. 7532 SK Enschede (The Netherlands) info@sekobenelux.com CHINA n Seko China Ltd 072750 Hebei china@seko.com www.sekochina.com DENMARK n Seko Denmark DK-4930 Maribo info@seko.com FRANCE n Seko Lefranc-Bosi S.A. 77435 - Marne La Vallee Cedex 2 lefrancbosi@lefrancbosi.com service.commercial@seko.fr www.lefrancbosi.com GERMANY n Seko Deutschland GmbH 55252 Mainz - Kastel info@seko-messtechnik.de www.seko-germany.com
Subject to change without notice.
ITALY n Seko Spa [Process & Sytems] 20068 Peschiera Borromeo Milano info.psd@seko.com info@seko.com MEXICO n Sistemas de dosificacion de Mexico Seko C.P. 11560, Mxico D.F. info@seko.com ROMANIA n Seko Sieta S.r.l. 400393 Cluj-Napoca info.dpro@seko.com RUSSIA n OOO Seko 129347 - Moscow sekorussia@seko.com www.sekorussia.ru SINGAPORE n Seko Dosing Systems Asia Pacific Pte Ltd 608838 Singapore asiapacific@seko.com SOUTH AFRICA n Seko Southern Africa (PTY) Ltd Kyasand - Johannesburg Gauteng sales@sekosa.co.za
SPAIN n Seko Ibrica Sistemas de Dosificacin S.A. 08960 Sant Just Desvern Barcelona sekoiberica@sekoiberica.com SWEDEN n Seko Sweden 26123 Landskrona info@seko.com TURKEY n Seko Endstriyel Pompalar ve Proses Sistemleri San. ve Tic. Ltd. ti. Kartal Istanbul info@seko.com.tr www.seko.com.tr UNITED ARAB EMIRATES n Seko Middle East FZE P.O. Box 42090 Hamriyah Free Zone, Sharjah info@seko.ae sales@seko.ae UNITED KINGDOM n Seko UK Chemical Controls Ltd Harlow, Essex - CM19 5JH seko.uk@seko.com www.sekouk.com USA n Seko Dosing Systems Corporation Tullytown - PA 19007 sales@sekousa.com www.sekousa.com
For more information www.seko.com
> Seko SpA > Printed in Italy > BRO MCI 14A-UK

Control Instruments

Uploaded by

Copyright:

Available Formats

Control Instruments

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Control Instruments

Uploaded by

Copyright:

Available Formats

Control and Measuring Instruments

> technology > future

Single and twin-parameter control instruments

> water & industry > control and measuring instruments

Kontrol 500 Single parameter

K500PR K500CD K500ID K500OX K500CL K500T1 K500T2

Kontrol 502 Double parameters

> technology > future

> water & industry > control and measuring instruments

Kontrol 200 Single parameter

K200PR K200CD K200ID K200OX K200CL K200TB

> technology > future

> water & industry > control and measuring instruments

(*): Amperometric Chlorine CU+PT sensors

Kontrol 800 Single parameter

Model Kontrol CL 800 Kontrol CLP 800

Kontrol 800 Double parameters

> technology > future

Photometer System Photometer System

Multi parameter photometer instrument

> water & industry > control and measuring instruments

Code pH ORP Chlorine (Photometric chamber) Temperature

Description 014,00 pH 1500 mV 05,00 ppm (*)

Photometer Light Multi parameters

Photometer System Single parameter

Photometer System Multi parameters

Photometer Photometer Photometer

(*): Sea water application on demand code SPT3CLMW0001

> technology > future

Single and multiple-parameter control instruments

l pH / ORP l Conductivity l Chlorine l Chlorine Dioxide l Flow Rate

> water & industry > control and measuring instruments

ORP Conductivity Chlorine (Amperometric Cell) Chlorine and Chlo. Dioxide

Temperature Flow Rate

99 999,99 Liters/second (*)

Kontrol 40 Single parameter

Kontrol 42 Double parameters

Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42 Kontrol 42

> technology > future

Single or multi-parameter control instruments

> water & industry > control and measuring instruments

Description 014,00 pH 1500 mV 1200/102000/10020000 S

ORP Conductivity Temperature

Kontrol 20 Single parameter

Kontrol 22 Double parameters

> technology > future

SPH-4 HT SRH-4 HT-PT

> water & industry > control and measuring instruments

Code 9900105007 0130C at 6 bar 016 bar at 25C

1,5m cable + BNC

Code 9900105034 0130C at 6 bar 016 bar at 25C

Without temperature sensor

With temperature sensor (PT100)

- Drinking Water - Cooling Towers - Reverse Osmosis - Irrigation

Without temperature sensor

With temperature sensor (PT100)

With temperature sensor (PT100)

> water & industry > control and measuring instruments