Acuvim L Power Meter User Manual

Distributed by MicroDAQ.com, Ltd.
www.microdaq.com/accuenergy
(603) 746-5524
(603) 746-5524
(603) 746-5524
I
Copyright

2012 V1.45
This manual may not be altered or reproduced in whole or in part by any means
without the expressed written consent of Accuenergy.
The information contained in this document is believed to be accurate at the time of
publication, however, Accuenergy assumes no responsibility for any errors which may
appear here and reserves the right to make changes without notice. Please ask the
local representative for latest product specifcations before ordering.
[ Document #1030E2145 Revision Date: Jun., 2012 ]
(603) 746-5524
(603) 746-5524
II
Please read this manual carefully before installation, operation and maintenance of
Acuvim-L power meter.
The following symbols in this manual and on Acuvim-L series meters are used to
provide warning of danger or risk during the installation and operation of the meters.
Electric Shock Symbol: Carries information about procedures which must be
followed to reduce the risk of electric shock and danger to personal health.
Safety Alert Symbol: Carries information about circumstances which if not
considered may result in injury or death.
This mark indicates that this product is UL listed.
Installation and maintenance of the Acuvim-L power meter should only be performed
by qualifed, competent professionals who have received training and should have
experience with high voltage and current device.
Accuenergy shall not be responsible or liable for any damages caused by improper
meter installation and/or operation.
(603) 746-5524
(603) 746-5524
III
Content
Chapter 1 Introduction-------------------------------------------------------------------1
1.1 Functionality ---------------------------------------------------------------2
1.2 Areas of application -------------------------------------------------------------2
1.3 Meter overview--------------------------------------------------------------3
Chapter 2 Installation---------------------------------------------------------------------7
2.1 Appearance and dimensions---------------------------------------------9
2.2 Installation Method-------------------------------------------------------------12
2.3 Wiring -------------------------------------------------------------------------------15
2.3.1 Terminal Strips--------------------------------------------------------------15
2.3.2 Power Requirement-------------------------------------------------------17
2.3.3 Voltage Input Wiring------------------------------------------------------ 20
2.3.4 Current Input Wiring-------------------------------------------------------22
2.3.5 Frequently Used Input Wiring------------------------------------------ 24
2.3.6 Digital Output---------------------------------------------------------------29
2.3.7 Digital Input----------------------------------------------------------------30
2.3.8 Communication------------------------------------------------------------31
Chapter 3 Meter Operation and Parameter Setting-------------------------------33
3.1 Display Panel and Keys-------------------------------------------------34
3.2 Metering Data Reading--------------------------------------------------36
3.3 Statistics Display-------------------------------------------------------------44
3.3.1 Max/Min value of Voltage and Current------------------------------44
3.3.2 Max/Min of Power and Demand--------------------------------------47

(603) 746-5524
(603) 746-5524
IV

3.3.3 Display Power Quality Parameter------------------------------------47
3.4 System Parameter Setting ----------------------------------------------------49
3.5 DO Parameter Setting and Expansion module Setting---------------56
3. 6 DI Status Di spl ay ---------------------------------------------63
3. 7 TOU Energy and Maxi mum Demand Di spl ay--------------64
3.8 Measurement Methods and Parameter Defnitations------------------67
Chapter 4 Communication--------------------------------------------------------------85
4. 1 Modbus protocol introduction---------------------------------86
4. 2 Modbus protocol -------------------------------------------------87
4.3 Communication format--------------------------------------------------89
4.4 Data address table-----------------------------------------------------------94
Appendix A Technical data and Specifcation-----------------------------------------------138
Appendix B Ordering Information-------------------------------------------------------------142
Appendix C Revision History--------------------------------------------------------------------144
(603) 746-5524
(603) 746-5524
V
Starting!
Congratulations!
You have purchased an advanced, versatile and multifunction power meter. This
meter can work as a remote terminal unit (RTU) that contributes to your systems
stability and reliability by providing real-time power quality monitoring and analysis.
When you open the package, you will fnd the following items:
1. Acuvim-L power meter 1
2. Terminal Blocks 3 (2 for basic model)
3. [INSERT] Installation Clips 4
4. Product Disk (Manual, Warranty, Software) 1
5. Additional documentation
(Quick Setup Guide, Calibration Certifcate) 2
To avoid complications, please read this manual carefully before installation and
operation of the Acuvim II series meter.
Chapter 1 Chapter 1 Introduction.
Chapter 2 Installation and Wiring.
Chapter 3 Meter Display and Parameter Settings.
Chapter 4 Communication Protocols and Modbus Map.
Appendix Technical Data, Specifcations and Ordering Information.
(603) 746-5524
(603) 746-5524
VI
(603) 746-5524
(603) 746-5524
Chapter 1 Introduction
1.1 Functionality
1.2 Areas of Application
1.3 Meter Overview
(603) 746-5524
(603) 746-5524
2
1.1 Functionality
Multifunction, high accuracy
Acuvim-L series multifunction power meter is designed with the latest
microprocessor and digital signal process technology. It can measure voltage,
current, active power, reactive power, apparent power, power factor for three
phases, individual harmonics up to the 15
th
or 25
th
order, THD, real and reactive
energy, current and demand and max/min values for real time readings.
The optional Digital Output and RS485 communication can be used for sending
energy pulse output and event alarming signals. The RS485 port also can be used
for remote meter controlling and data collection. Acuvim-L series meter delivers
exceptional metering functionality and provides a cost effective solution for
customers.
Compact and Easy to Install
Acuvim-L series meter can be installed into a standard ANSI C39.1 (4" round) or
an IEC 92mm DIN (square) slot. With the 51mm depth , the meter can be installed
in a small cabin. Installation clips are used for easy installation and removal.
Easy to use
All metering data and setting parameters can be accessed by using the front
panel keys or via the communication port. Setting parameters are stored in the
EEPROM so that content will be maintained even when the meter is powered of.
Multiple Wiring Modes
The Acuvim-L series meter can be used in high voltage, low voltage, three phase
three wires, three phase four wires and single phase systems by using diferent
wiring mode settings.
1.2 Application Area
(603) 746-5524
(603) 746-5524
3
Acuvim-L series meter is the ideal choice for replacing traditional, analog
electric meters. It uses true RMS measuring methods so that nonlinear load can
be monitored. Except providing means of monitoring and measuring power
distribution automation system, it can also be used as a remote terminal unit
(RTU) for monitoring and controlling a SCADA system. Users can access all
measurement parameters via the optional RS485 communication port with
Modbus
TM
protocol. Main application areas Electric Switch Gear and Control
Panels include:
Power Distribution Automation Electric Switch Gear and Control Panels
Industrial Automation Building Automation
Energy Management Systems Marine Applications
Renewable Energy
1.3 Meter Overview
The Acuvim-L series have six standalone models: Acuvim-AL(basic model),
Acuvim-BL(basic model + 2DO), Acuvim-CL(basic model + RS485), Acuvim-
DL(basic model + RS485 + Extend IO), Acuvim-EL(TOU + RS485 + Extend IO) and
Acuvim-KL(Simplifed Acuvim-CL). Please see table 1-1 for their functionalities
and details.
Table 1-1 Functions of Acuvim-L series
Function Parameters AL BL CL DL EL KL
Real Time
Measuring
Phase Voltage U1, U2, U3

Line Voltage U12, U23, U31

Current
I1, I2, I3,In,(Acuvim-KL
non-neutral current
measurement)

Power P1, P2, P3, Psum

Reactive Power Q1, Q2, Q3, Qsum
Apparent Power S1, S2, S3, Ssum
Power Factor PF1, PF2, PF3, PF
Load Nature L/C/R
Frequency F Hz
(603) 746-5524
(603) 746-5524
4
Function Parameters AL BL CL DL EL KL
Energy
& Demand
Energy Ep_imp, Ep_exp
Reactive Energy Eq_imp, Eq_exp
Apparent
Energy
Es
Current
Demand
Dmd_I1, Dmd_I2,
Dmd_I3

Power Demand
Dmd_Psum,
Dmd_Qsum,
Dmd_Ssum

TIME OF USE Energy
TOU, 4 Tar i f f s ,
12 Seasons, 14
Schedules
Power Quality
Voltage
Unbalance
U_unbl
Current
Unbalance
I_unbl
Voltage THD
THD_V1, THD_V2,
THD_V3

Current THD
THD_I1, THD_I2,
THD_I3

Individual
Harmonics
2
nd
to 15
th
(Voltage
and Current)
(Acuvim-DL is 2
nd

to 25
th
)

Statistics
Max Current
Demand
Dmd_I1_max,
Dmd_I2 _max,
Dmd_I3_max

Max Power
Demand
Dmd_Psum_max,
Dmd_Qsum_max,
Dmd_Ssum_max

Max/Min
Voltage

Max/Min
Current

(603) 746-5524
(603) 746-5524
5
Note: Possessed functions Optional function Blank NA
HOUR
Running Hour Hour
Load Running
Hour
Hour
I/O
Energy Pulse
Output
2 DO, confgured
as pulse output
for kWh and
kvarh, the pulse
constant and
width can be set
Alarm Output
COMMUNICATION
RS-485
Modbus-RTU
Protocol,

Second RS-485/
PROFIBUS
Modbus-
RTU Protocol/
PROFIBUS-DP
V0 Protocol

Extended I/O 4DI, 2DO
SOE, Pulse
Counter, Pulse
output, Alarm
output

(603) 746-5524
(603) 746-5524
6
(603) 746-5524
(603) 746-5524
6
Chapter 2 Installation
2.1 Appearance and Dimensions
2.2 Installation Methods
2.3 Wiring
(603) 746-5524
(603) 746-5524
8
Considerations When Installing Meters
Installation of the meter must be performed by qualified personnel only, who
follow standard safety precautions through the installation procedures. Those
personnel should have appropriate training and experience with high voltage
devices. Appropriate safety gloves, safety glasses and protective clothing are
recommended.
During normal operation, dangerous voltage may flow through many parts of
the meter, including: terminals, any connected CTs (Current Transformers) and PTs
(Potential Transformers), all I/O (Inputs and Outputs) modules and their circuits. All
primary and secondary circuits can, at times, produce lethal voltages and currents.
AVOID contact with any current-carrying surfaces.
The meter and its I/O output channels are NOT designed as primary protection
devices and shall NOT be used for primary circuit protection or in an energy-limiting
capacity. The meter and its I/O output channels can only be used as secondary
protection. AVOID using the meter under situations where failure of the meter may
cause injury or death. AVOID using the meter for any application where risk of fre
may occur.
All meter terminals should be inaccessible after installation.
Do NOT perform Dielectric (HIPOT) test to any inputs, outputs or communication
terminals. High voltage testing may damage electronic components of the meter.
Applying more than the maximum voltage the meter and/or its modules can
withstand will permanently damage the meter and/or its modules. Please refer to
the specifcations for all devices before applying voltages.
(603) 746-5524
(603) 746-5524
9
The installation method is introduced in the chapter. Please read this chapter
carefully before beginning installation .

2.1 Appearance and Dimensions
Units: mm(inches)
Gasket
9
1
.
0
0

(
3
.
5
8
3
)
35.90
(1.413)
50.70 (1.996)
9
6
.
0
0

(
3
.
8
0
0
)
96.00 (3.800)
C
C
C
9
1
.
0
0

(
3
.
5
8
3
)
35.90
10.00
(0.394)
14.00
(0.551)
35.90
C
9
1
.
0
0

(
3
.
5
8
3
)
3
8
.
0
0

(
1
.
4
9
6
)
7.60 (0.300)
(1.413)
(1.413)
50.70 (1.996)
C
Front View of the Display Meter and
Remote Display Unit
Gasket
Side View of the
Display Meter
Side View of the Remote
Display Unit
Side View of the DIN
rail Meter
Multifunction Power Meter
H P E V/A
-L
A
(603) 746-5524
(603) 746-5524
10
1
Part Name Description
C LCD Display Large bright white backlight LCD display.
C Front Casing
Visible portion (for display and control) after
mounting onto a panel.
C Key Four keys are used to select display and set.
C Enclosure
The Acuvim II series meter enclosures is made
of high strength anti-combustible engineering
plastic.
C DIN rail
Used for Installation 35mm rail of the DIN rail
Meter.
Voltage Input Terminals Used for voltage input.
C Current Input Terminals Used for current input.
Power Supply Terminals Used for aux. power supply input.
Communication Terminals Communication output.
1 Interface
Used for link the remote display unit and the DIN
rail meter.
Installation Clip Used for fxing the meter to the panel.
Gasket
Insert the gasket in between the meter and the
cutout to cover up gaps from the round hole.
Rear View Rear View of the Remote

Display Unit
Installation Clip
Fig.2-1 Appearance and dimensions
(603) 746-5524
(603) 746-5524
11
IO module appearance and mechanical dimensions

PROFIBUS module appearance and mechanical dimensions

19 .5 mm
5
5
.
6
0
90.00
22.00
Fig.2-3 structure confguration of PROFIBUS modules
Fig.2-2 structure confguration of IO modules
(603) 746-5524
(603) 746-5524
12
2.2 Installation Methods
Environment
Please check the environmental temperature
and humi di t y accor di ng t o Acuvi m- Ls
requirement to ensure the power meter can
work well.
1. Temperature
Operation: -25C to 70C Storage: -40C to 85C
2. Humidity
5% to 95% No condensation
3. Location
Acuvim-L power meter should be installed in a dry and dust free environment.
Avoid exposing meter to excessive heat, radiation and high electrical noise
source.
Installation steps
Acuvim-L series meter can be installed into a standard ANSI C39.1 (4 round) or
an IEC 92mm DIN (square) form. 1. Cut a square or round hole on the panel of
the switch gear. The cutting size shows as Fig.2-4.

Fig.2-4 Panel cutting
Note
Temperature and humidity
of the environment
must accord with the
requirement of acuvim-L,
Otherwise it may cause
the meter damaged.
A
L
U
M
0
2
0
6
Unit: mm (inches)
92
+0.5
-0.0
9
2
+
0
.
5
-
0
.
0
Cutting
Panel
101.6
Panel
+0.5
-0.0
(3.622)
(4.000)
(603) 746-5524
(603) 746-5524
13
2. Remove the clips from the meter and put Acuvim-L into the square hole from
the front side.
Fig.2-5 Put the meter into the square
3. Install the clips to the meter from backside and push the clips tightly so that
the meter is fxed on the panel.
Fig.2-6 Use clips to fx the meter
A
L
U
M
0
2
0
7
Panel
Panel
Panel
A
L
U
M
0
2
0
8

(603) 746-5524
(603) 746-5524
14
Module Installation
(1) The extend module could be installed from the bottom of the meter .
(2) The extend module is fxed on the meter by the screw.
(3) Please install the PROFIBUS module frst if both IO and PROFIBUS module are
selected.
Fig.2-7 IO installation diagram
Note: Acuvim-DL and Acuvim-EL Power meter can connect at most one IO
module and one PROFIBUS module at the same time.
(603) 746-5524
(603) 746-5524
15
2.3 Wiring
2.3.1 Terminal Strips
There are three or four terminal strips at the back of the Acuvim-L series meter
depending on different models. The terminal strip diagrams are shown in
below. The three phase voltage and current are represented by using 1, 2, and 3
respectively. These numbers have the same meaning as A, B, and C or R, S, and T
used in other literature.
Current input terminal strips
Voltage input terminal strips
Power supply terminal strips
!
ALUM0210
7 8 9 10
V1 V2 V3 VN
ALUM0209
I11 I12 I21 I22 I31 I32
1 2 3 4 5 6
ALUM0211
13 12 11
N/- L/+
Power Supply
(603) 746-5524
(603) 746-5524
16
Communication terminal strips Digital output terminal strips

Fig.2-8 Terminal diagram of Acuvim-L
Before setting up the meters wiring, please
make sure that the switch gear has an earth
ground terminal. Connect both the meter and
the switch gear ground terminals together. The
following ground terminal symbol is used in this
users manual.

Note: Acuvim-AL does not have digital output and commnication terminal strips
Acuvim-BL has digital output terminal strip
Acuvim-CL/DL/EL/KL have communication terminal strip
Danger
Only qualified personnel
s h o u l d p e r f o r m t h e
wiring connection. Make
sure the power supply is
disconnected. Failure to
follow these instructions
may result in severe injury
or death.

ALUM0212
16 15 14
S B A
Comm Port
ALUM0213
16 15 14
DOC DO2 DO1
Digital Output
Fig.2-9 Expansion module terminal description
Fig.2-10 Safety Earth Symbol
Safety Earth Connection
Digital Input Digital Output Comm Port
DIC DI4 DI3 DI2 DI1 DO22 DO21 DO12 A B DO11 S
(603) 746-5524
(603) 746-5524
17
L
N Acuvim-L
1A FUSE
Power Supply
Ground
11
12
13
2.3.2 Power Requirement
Auxiliary power
There are two Auxiliary Power Supply options for the
Acuvim-L series meter:
1. Standard: 100~415Vac (50/60Hz) or 100~300Vdc
2. Low Voltage DC Option: 20-60Vdc
Choose the option according to the application.
The meters typical power consumption is very low
and can be supplied by an independent source or by the measured load line. A
regulator or an uninterrupted power supply (UPS) should be used under high
power fuctuation conditions. Terminals for the auxiliary power supply are 11, 12 ,
13 (L, N, ).
The typical wiring connection is shown as Fig.2-11.
Fig.2-11 wiring connection of power supply
The wire of power supply should be AWG22-16 or 0.6-1.3mm
2
. A fuse (typical
1A/250Vac) should be used in the auxiliary power supply loop. No.13 terminal
must be connected to the ground terminal of switchgear. An isolated
transformer or EMC filter should be used in the auxiliary power supply loop if
there is a power quality problem in the power supply.
Note
Make sure the power
s uppl y vol t age i s
within the required
auxiliary power supply
range.
ALUM0214
(603) 746-5524
(603) 746-5524
18
Fig.2-12 wiring connection of auxiliary power supply with EMC flters
Voltage input
Maximum input voltage for the Acuvim-L series meter shall not exceed
400LN/690LL VAC rms for three phase or 400LN VAC rms for single phase.
Potential Transformer (PT) must be used for high voltage systems. Typical
secondary output for PTs shall be less than or equal to 400V. Please make sure to
select an approprate PT to maintain the measurement accuracy of the meter.
A fuse (typical 1A) should be used in the voltage
input loop. The wire for voltage input could be
AWG16-12 or 1.3-2.0mm
2
.
Note: In no circumstance should the secondary of
the PT be shorted. The secondary the PT should be
grounded at one end.
Please refer to the wiring diagram section for further
details.
Current input
Current Transformers (CTs) are required in most engineering applications.
Typical current rating for the secondary side of the CT shall be 5A (standard)
or 1A (optional, please refer to the ordering information appendix for further
Note
The secondary of PT
can not be shorted;
ot her wi s e i t may
cause severe damages
to the instrument.
ALUM0215
Ground
1A FUSE
Power Supply
Acuvim-L
L
N
L
N
G
L
N
G
EMC Filter
12
13
11
(603) 746-5524
(603) 746-5524
19
details). CTs must be used if the system rated current is over 5A. The accuracy of
the CT should be better than 0.5% with rating over 3VA is recommended in order to
preserve the meters accuracy. The wire between CTs and the meter shall be as short
as possible. The length of the wire may increase the error of the measurement.
The wire size of current input could be AWG15-10 or 1.5-2.5mm
2
.
Note: The secondary side of the CT should not be open circuit in any
circumstance when the power is on. There should not be any fuse or switch in
the CT loop. One end of the CT loop should be connected to the ground.
Vn connection
Vn is the reference point of the Acuvim-L voltage input. Low wire resistance
helps improve the measurement accuracy. Different system wiring modes
require different Vn connection method. Please refer to the wiring diagram
section for more details.
Three phase wiring diagram
Acuvim-L can satisfy almost all kinds of three phase wiring diagram. Please read
this section carefully before choosing the wiring diagram suitable for your power
system.
Voltage and current input wiring mode can be set separately in the meter
parameter setting process. The voltage wiring mode can be set as 3-phase 4-line
Wye(3LN), 3-phase 3-line direct connection mode(3LL), 3-phase 4-line 2PT Wye
mode(2LN*) and 3-phase 3-line open delta (2LL). The current input wiring mode
can be set as 3CT, 2CT and 1CT*. Any voltage wiring setup can be matched with
any one of the current wiring setup.
Note: * wiring method not applicable to Acuvim-EL and Acuvim-KL
(603) 746-5524
(603) 746-5524
20
2.3.3 Voltage Input Wiring
3-Phase 4-Line Wye mode (3LN)
The 3-Phase 4-Line Wye mode is popularly used in low voltage electric
distribution power system. For voltage lower than 400LN/690LL Vac, power line
can be connected directly to the meters voltage input port as shown in Fig.2-
13a. In the high voltage input system, 3PT Wye mode is often used as in Fig.2-
13b. The meter should be set to 3LN for both voltage levels.
Fig.2-13a 3LN direct connection
Fig.2-13b 3LN connection with 3PTs
LINE
LOAD
V1
V2
V3
VN
Acuvim-L
7
8
9
10
A B C N
1A FUSE
ALUM0221
LINE
LOAD
V1
V2
V3
Acuvim-L
7
8
9
A B C N
1A FUSE
10
VN
ALUM0222
(603) 746-5524
(603) 746-5524
21
3-Phase 4-Line 2PT mode (2LN*)
In a 3-Phase 4-Line Wye system, 2PT Wye mode is often used when the 3 phase
power system is balanced. The connection method is shown in fig.2-14. The
voltage of V2 is calculated according to the V1 and V3. The voltage input mode
of the meter should be set to 2LN for the 2PT voltage input wiring mode.
Fig.2-14 2LN connection with 2PTs (*)
3-Phase 3-Line direct connection mode (3LL)
In a 3-Phase 3-Line system, power line A, B and C are connected to V1, V2 and V3
directly. Vn is foated. The voltage input mode of the meter should be set to 3LL.
Fig.2-15 3LL 3-phase 3-line direct connection
LINE
LOAD
V1
V2
V3
Acuvim-L
7
8
9
A B C N
10
1A FUSE
VN
ALUM0223
LINE
LOAD
V1
V2
V3
VN
Acuvim-L
7
8
9
10
A B C
1A FUSE
ALUM0224
(603) 746-5524
(603) 746-5524
22
3-Phase 3-Line open Delta Mode (2LL)
Open delta wiring mode is often used in high voltage system. V2 and Vn
connected together in this mode. The voltage input mode of the meter should
be set to 2LL for this voltage input wiring mode.
Fig.2-16 2LL with 2PTs
2.3.4 Current Input Wiring
3CT
The 3CT current wiring configuration can be used when either 3CTs are
connected (as shown in Fig.2-17) or 2CTs are connected (as shown in Fig.2-18)
to the system. In either case, there is current fowing through all three current
terminals.
Fig.2-17 3CT-a
LINE
LOAD
V1
V2
V3
Acuvim-L
7
8
9
A B C
10
Vn
1A FUSE
ALUM0225
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I 32
8
6 I 12
I 21
I 22
I 31
6
Terminal block
1
2
3
4
5
ALUM0226
(603) 746-5524
(603) 746-5524
23
Fig.2-18 3CT-b
2CT
The difference between Fig.2-18 and Fig.2-19 is that no current flows through
current input terminal I21 and I22. The I2 value is calculated from formula
i1+i2+i3=0. The current input mode of the meter should be set to 2CT .
Fig.2-19 2CT
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I 32
8
6 I 12
I 21
I 22
I 31
6
Terminal block
1
2
3
4
5
ALUM0227
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
ALUM0228
(603) 746-5524
(603) 746-5524
24
1CT (*)
If it is a three phase balance system, 1 CT connection method can be used. The other
two channels are calculated accordingly.
Fig.2-20 1CT (*)
2.3.5 Frequently used wiring method
I n this section, most common voltage and current wiring connection
combinations are put together into different diagrams. In order to display
measurement readings correctly, please select the approprate wiring diagram
according your setup and application.
Note: * wiring method is not applicable to Acuvim-EL. Acuvim-KL supports
1LN-2CT and 1LN-1CT, which are depicted in Fig. 2-29 and Fig 2-28 respectively.
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I 32
8
6 I 12
I 21
I 22
I 31
6
Terminal block
1
2
3
4
5
ALUM0229
(603) 746-5524
(603) 746-5524
25
1. 3LN, 3CT with 3 CTs (Wiring mode: 3LN, 3CT)
Fig.2-21 3LN, 3CT with 3CTs
2. 3LN, 3CT with 2 CTs (Wiring mode: 3LN,3CT)
Fig.2-22 3LN, 3CT with 2CTs
N
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I 32
8
6 I 12
I 21
I 22
I 31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
ALUM0231
N
LINE
LOAD
A B C
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3
7 8 9 10
1A FUSE
VN
ALUM0230
(603) 746-5524
(603) 746-5524
26
3. 2LN, 2CT (Wiring mode: 2LN, 2CT*)
Fig.2-23 2LN, 2CT(*)
4. 2LN, 1CT (Wiring mode: 2LN, 1CT*)
Fig.2-24 2LN, 1CT(*)
LOAD
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3
7 8 9 10
1A FUSE
LINE
A B C N
VN
ALUM0232
LOAD
I11
Acuvim-L
5
7
9
I 32
8
6 I 12
I 21
I 22
I 31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
LINE
A B C N
ALUM0233
(603) 746-5524
(603) 746-5524
27
5. 2LL, 3CT (Wiring mode: 2LL, 3CT)
Fig.2-25 2LL, 3CT
6. 2LL, 2CT (Wiring mode: 2LL, 2CT*)
Fig.2-26 2LL, 2CT(*)
LOAD
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
LINE
A B C
ALUM0235
LOAD
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
LINE
A B C
ALUM0234
(603) 746-5524
(603) 746-5524
28
7. 2LL, 1CT (Wiring mode: 2LL, 1CT*)
Fig.2-27 2LL, 1CT(*)
8. Single Phase 2 Line (wiring mode: 3LN, 3CT)
Fig.2-28 Single Phase 2 Lines
LOAD
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
LINE
A B C
ALUM0236
N
LINE
LOAD
A
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
ALUM0237
(603) 746-5524
(603) 746-5524
29
9. Single Phase 3 Line (Wiring mode: 3LN, 3CT)
Fig.2-29 Single Phase 3 Lines
2.3.6 Digital Output (DO)
There are two digital outputs for Acuvim-BL. The digital output circuit of Acuvim-
DL/EL extension module is the same as Acuvim-BL. The terminals of the digital
output are DO1 (14), DO2 (15) and DOC (16). These two digital outputs can be
used as energy pulse output or over/under limit alarming output.
Digital output circuit form is Photo-MOS. The simplifed circuit is as below:
DO1
VCC
External
Power Supply
OUT
Photo-MOS
Acuvim-L
AC/DC
DOC
J
ALUM0239
N
LINE
LOAD
A
I11
Acuvim-L
5
7
9
I32
8
6 I12
I21
I22
I31
6
Terminal block
1
2
3
4
5
V1 V2 V3 VN
7 8 9 10
1A FUSE
B
ALUM0238
Fig.2-30 Digital output circuit
(603) 746-5524
(603) 746-5524
30
The max output voltage and current are 250Vac/300Vdc and 100mA.
When the digital output is used as over/under limit alarming output, the upper
and lower limit of the parameter, time interval and output port can be set from
the meter front.
2.3.7 Digital Input(DI)
There are 4 dry-contact digital input in extension modules respectively. The
digital input circuit can be used to detect remote signals, or be used as a counter
of input pulses.

Fig.2-31 DI input circuit diagram
The circuit drawing of digital input is simplifed as fg.2-31. When K is switched
of, OUT is in high state. When K is switched on, OUT is in low state. The wire of
digital input should be chosen between AWG22~16 or 0.5~1.3mm
2
.
Photo-MOS
circuit
(603) 746-5524
(603) 746-5524
31
2.3.8 Communication
Acuvim-L series meter uses RS485 serial communication and the Modbus-
RTU protocol. The terminals of communication are A, B, and S (14, 15 and 16).
A is diferential signal +, B is diferential signal - and S is connected to the shield
of twisted pair cable. Up to 32 devices can be connected on a RS485 bus. Use
good quality shielded twisted pair cable, AWG22 (0.5mm2) or larger. The overall
length of the RS485 cable connecting all devices can not exceed 1200m (4000ft).
Acuvim-L series meter can be used as a slave device of a master device such as
PC, PLC, Data Collector and RTU.
If the master does not have RS485 communication port, a converter(such as a
RS232/RS485 or a USB/RS485 converter) will be required. Typical RS485 network
topologies include line, circle and star (wye).
Data transfer format is start bit + 8 data bits + parity + stop bit. NON1, NON2, odd
and EVEN could be selected in the mode of parity. NON1 represents non-parity,
single stop bit; NON2 represents non-parity, double stop bit; odd represents odd-
parity, single stop bit; EVEN represents EVEN-parity, single stop bit.
Acuvim-AL/BL/CL/DL support Modbus-RTU agreement, but have not be
standardized, that is to say they do not support parity setting. In order to
improve the quality of communications, now ofers the following Suggestions:
The shield of the RS485 cable must be connected to the ground at one end
only. Every A(+) should be connected to A(+), B(-) to B(-), or it will infuence the
network, even damage the communication interface.
T type connection topology should be avoided. This means no new branches
except from the starting point.
Keep communication cables away as much as possible from sources of electrical
noise. When several devices are connected (daisy chain) to the same long
communication line, an anti signal refecting resistor (typical value 120- 300/
0.25W) is often used at the end of the circuit ( the last meter of the chain)
(603) 746-5524
(603) 746-5524
32
if the communication quality is distorted.
Use RS232/RS485 or USB/RS485 converter with optical isolated output and surge
protection.
(603) 746-5524
(603) 746-5524
3.1 Display Panel and Keys
3.2 Metering Data
3.3 Statistics Display
3.4 System Parameter Setting
3.5 DO Parameter Setting and Expansion Module Setting
3.6 DI Status Display
3.7 TOU Energy and Maximum Demand Display
3.8 Measurement Methods and Parameters Defnitations
Chapter 3 Meter Operation and
Parameter Setting
(603) 746-5524
(603) 746-5524
34
Operational details of the meter will be described in this chapter. This includes
viewing real-time metering data and setting parameters using different key
combination.
3.1 Display Panel and Keys
The front of the Acuvim-L series meter consists of an LCD screen and four control
keys. All display segments are shown as Fig.3-1 below:
Fig.3-1 All display segments
10
9
8
7
6
5
4
1 2
3
8
ALUM0301
(603) 746-5524
(603) 746-5524
35
SN display Description
1
Three lines of " " digits
in the metering area
Display metering data
Vol tage, current, power, power f actor, THD,
frequency, demand, unbalance factor, max, min etc.
2
Status display area
One line of" " digits at
the top of display panel
Display current status
Meter: metering status; Max: maximum value; Min:
minimum value; THD: display Har: display individual
harmonic for voltage and current.
3 Item icon
Item icon
U: voltage; I: current, P: active power; q: reactive
power; PF: power factor; when displaying harmonic
content, the little "8" digits show the harmonic order.
4 3-phase unbalance Unbalance icon
5 Load nature
: inductive load;
: capacitive load.
6 Energy icon Imp: import energy; exp: export energy
7
Communication indicator
No icon: no communication
With icon: communication
8
Energy pulse
output indicator
.
No icon: no pulse output
With icon: pulse output
9 Time icon With icon: display running time
10 Unit
Indicate data unit
Voltage: V, kV, Current: kA, A, Power: kW and MW,
Reactive Power: kvar and Mvar, Apparent Power:
kVA and MVA, Frequency: Hz, Energy: kWh, Reactive
Power: kvarh, Percentage: %
There are four delicate keys on the front panel, labeled H, P, E and V/A from left to
right. Use these four keys to read metering data and set the parameters.
Note: If the LCD backlight is of, press any key one time to bring the backlight on
(603) 746-5524
(603) 746-5524
36
3.2 Metering Data
Acuvim-L series meter displays the voltage metering screen (default screen)
when frst powered up. Diferent key combinations show diferent screen. Press
V/A to show real-time metering data; press E to show energy parameters; press
P to show power parameters; press H to show power quality information; press
H and E together simultaneously to show max/min information, unbalance
and individual harmonics.
pressH and V/A together simultaneously to show basic parameter setting.
pressP and V/A together simultaneously to show DI Status. pressE and V/A
together simultaneously to show TOU Energy.
Note: No harmonic contents will be displayed in Acuvim-EL and Acuvim-KL.
Press V/A to read voltage and current in the metering area. The screen will
proceed to the next display as you press V/A each time. It will go back to the
frst screen if you press V/A at the last screen.
The 1
st
screen: Voltage for each phase: U1, U2 and
U3. As shown in Fig.3-2, U1=380.2 V, U2=380.0 V,
U3=379.8 V.
Load nature is inductive, and communication
status is good.
Note: Since load nature and communication
status belong to system information, the icons
are displayed on every screen.
ALUM0302
Fig.3-2 Three phase voltage
(603) 746-5524
(603) 746-5524
37
Press V/A to go to the next screen.
The 2
nd
screen: Line to line voltage: U12, U23
and U31. As shown in Fig.3-3, U12=658.5 V,
U23=658.0 V, U31=657.8 V.
The 3
rd
screen: Current for each phase: I1, I2 and
I3. As shown in Fig. 3-4, I1=2.501 A, I2=2.500 A,
I3=2.499 A.
The 4
th
screen: Neutral current. As shown in
Fig.3-5, In=0.000 A.
Fig.3-3 Three phase voltage
ALUM0303
Fig.3-4 Three phase current
ALUM0304
Fig.3-5 Neutral current
ALUM0305
(603) 746-5524
(603) 746-5524
38
The 5
th
screen: Current demand of each phase.
As shown in Fig.3-6, Dmd_I1=2.503 A, Dmd_
I2=2.501 A, Dmd_I3=2.500 A.
Press V/A to go back to the 1st screen.
Note: For Acuvim KL, only the current page is displayed. When the wiring is
single-phase two-line, it only shows A-phase current; If the wiring is single-phase
three-wire, it displays phase A and phase B current. For other L series meters,
when the voltage wiring is set to 2LL or 3LL, it will not display phase voltage and
neutral current , there is no the 1
st
and 4
th
screen. Press V/A to switch among the
2
nd
, 3
rd
and 5
th
screens.
Press P to display power related parameters.
The 1
st
screen: Power of each phase.
As shown in Fig.3-7, P1=0.475 kW, P2=0.475 kW,
P3=0.474 kW.
Inductive load, communication status is good.
Press P to go to the next screen.
Fig.3-6 Demand current
ALUM0306
Fig.3-7 Three phase power
ALUM0307
(603) 746-5524
(603) 746-5524
39
The 2
nd
screen: Reactive power of each phase.
As shown in Fig.3-8, Q1=0.823 kvar, Q2=0.823
kvar,Q3=0.822 kvar.
Press P, go to the next screen.
The 3
rd
screen: Apparent power of each phase.
As shown in Fig.3-9, S1=0.950 kVA,
S2=0.951 kVA,S3=0.950 kVA.
The 4
th
screen: System total power, reactive power
and apparent power.
As shown in Fig.3-10, Psum=1.426 kW,
Qsum=2.471 kvar, Ssum=2.853 kVA.
Fig.3-8 Three phase reactive power
ALUM0308
Fig.3-9 Three phase apparent power
ALUM0364
Fig.3-10 Power reactive and
apparent power
ALUM0309
(603) 746-5524
(603) 746-5524
40
The 5
th
screen: Power factor of each phase:
PF1,PF2, PF3.
As shown in Fig.3-11, PF1=0.500, PF2=0.499,
PF3=0.500.
The 6
th
screen: System average power factor PF
and system frequency F.
As shown in Fig.3-12, PF=0.500, F=50.01 Hz.
The 7
th
screen: System power demand Dmd_
P, reactive power demand Dmd_Q and apparent
power demand Dmd_S.
As shown in Fig.3-13, Dmd_P=1.425 kW, Dmd_
Q=2.472 kvar, Dmd_S = 2.850 kVA.
Note: for Acuvim-KL, if the wiring is set to 2LL, or
3LL, there is no single-phase power display, press
P to display the fourth screen. the 4
th
screen only.
Fig.3-13 System power demand
Fig.3-11 Three phase power factor
ALUM0310
Fig.3-12 Power factor and
frequency
ALUM0311
ALUM0312
(603) 746-5524
(603) 746-5524
41
For other series meters, if the wiring is set to 2LL, or 3LL, there is no single-phase
power and single-phase power factor displayed, press P to switch between
screens only 4,6,7.
The 1
st
screen: Import energy
As shown in Fig. 3-14, Ep_imp=50.9 kWh.
Press E, go to the next screen.
The 2
nd
screen: Export energy.
As shown in Fig. 3-15, Ep_exp=1.8 kWh.
Press E, go to the next screen.
The 3
rd
screen: Inductive (import) reactive energy.
As shown in Fig. 3-16, Eq_imp=3.9 kvarh.
Press E to go to the next screen.
Fig.3-16 Import reactive energy
Fig.3-14 Import energy
Fig.3-15 Export energy
ALUM0315
ALUM0313
ALUM0314
(603) 746-5524
(603) 746-5524
42
The 4
th
screen: Capactive (export) reactive energy.
As shown in Fig. 3-17, Eq_exp=1.5 kvarh.
The 5
th
screen: Apparent energy.
As shown in Fig.3-18, Es = 3.0kVAh.
The 6
th
screen: Run hours.
As shown in Fig.3-19, Run_Hour=12.3 hours.
Fig.3-17 Export reactive energy
ALUM0316
Fig.3-18 Apparent energy
ALUM0317
Fig.3-19 Run hours
ALUM0318
(603) 746-5524
(603) 746-5524
43
The 7
th
screen: Load Run hours.
As shown in Fig.3-20, Load Run hour = 1.3 hours.
Note: This screen only applies to Acuvim-DL, EL
and KL.
Note: In real-time metering mode, Acuvim-AL,
Acuvim-BL, Acuvim-CL and Acuvim-DL display voltage and current THD when H
is pressed. No functions are associated with H for Acuvim-EL and Acuvim-KL.
The 1
st
screen: Voltage THD.
When voltage wiring mode is set to 3LN or 2LN*,
display shows phase voltage THD: THD_U1, THD_
U2, THD_U3.
Note: * is not applicable to Acuvim-EL and
Acuvim-KL.
As shown in Fig. 3-21, THD_U1=2.32%, THD_
U2=2.35%, THD_U3=2.28%.
When voltage wiring mode is set to 2LL or 3LL,
display shows line to line voltage THD: THD_U12,
THD_U23, THD_U31.
As shown in Fig.3-22, THD_U12=2.30%,
THD_U23=2.28%, THD_U31=2.25%.
Press H to go to the next screen.
Fig.3-21 Phase voltage THD
ALUM0319
ALUM0320
Fig.3-22 Line to line voltage THD
Fig.3-20 Load Run hours
(603) 746-5524
(603) 746-5524
44
The 2
nd
screen: Phase current THD: THD_I1, THD_
I2, THD_I3.
As shown in Fig 3-23, THD of three phase current,
THD_I1=1.89%, THD_I2=1.83%, THD_I3=1.85%.
Press H key, go back to the 1
st
screen.

3.3 Statistics Display
Press H and E simultaneously to enter the statistic display mode. Maximum
and minimum value for metering parameters are demand, voltage and current
unbalance factor, and individual voltage and current harmonic. Press H and E
simultaneously again to exit to the real-time metering mode.
Note: Acuvim-EL and Acuvim-KL will not show harmonic contents.
3.3.1 Display Max and Min of the voltage and current and Peak Demandof
current .
Press V/A key under the statistics display mode
to display the Min and Max value of voltage,
current and current demand.
The 1
st
screen: Max value of phase voltage. The
Max icon is shown on the top of screen.
As shown in Fig. 3-24, U1_max=380.3 V, U2_
max=380.2 V, U3_max=380.5 V.
Fig.3-23 Current THD
ALUM0321
Fig.3-24 Max value of phase voltage
ALUM0322
(603) 746-5524
(603) 746-5524
45
The 2
nd
screen: Min value of phase voltage. The
MIN icon shown on the top of screen.
As shown in Fig.3-25, U1_Min=379.6 V,
U2_Min=379.8 V, U3_Min=379.7 V.
Note: When voltage wiring of the meter is set to 2LL or 3LL, max/min phase
voltage screen (1
st
and 2
nd
screen) will not be displayed.
The 3
rd
screen: Max value of line to line voltage.
As shown in Fig 3-26, U12_Max=658.6 V,
U23_Max=658.3 V, U31_Max=658.3 V.
The 4
th
screen: Min value of line to line voltage.
As shown in Fig.3-27, U12_Min=657.8 V,
U23_Min=657.7 V, U31_Min=657.6 V.
Fig.3-25 Min value of phase voltage
ALUM0323
Fig.3-26 Max value of line to line
voltage
ALUM0324
Fig.3-27 Min value of line to
line voltage
ALUM0325
(603) 746-5524
(603) 746-5524
46
The 5
th
screen: Max value of current.
As shown in Fig.3-28, I1_Max=2.502 A ,
I2_Max=2.503 A, I3_Max=2.502 A .
The 6
th
screen: Min value of current.
As shown in Fig.3-29, I1_Min=2.498 A,
I2_Min=2.496 A, I3_Min=2.497 A.
The 7
th
screen: Peak current demand.
As shown in Fig 3-30, I1_Demand_Max=2.505
A, I 2_Demand_Max=2. 504 A, I 3_Demand_
Max=2.504 A.
Press V/A to go back to the frst screen.
Fig.3-28 Max value of current
ALUM0326
Fig.3-29 Min value of current
ALUM0327
Fig.3-30 Peak current demand
ALUM0328
(603) 746-5524
(603) 746-5524
47
3.3.2 Display the Max value of power and reactive power demand.
Press P under the statistics display mode to display the peak value for power,
reactive power and apparent power demand.
As shown in Fig.3-31, P_Demand_Max=1.435 kW,
Q_Demand_Max=2.478 kvar, S_Demand_Max =
2.850 kVA.
3.3.3 Display power quality parameter
When press H under statistic display mode, Acuvim-AL, Acuvim-BL, Acuvim-
CL and Acuvim-DLwill display voltage and current unbalance factor as well
as individual voltage and current harmonic content (The THD of Acuvim-AL,
Acuvim-BL and Acuvim-CL is up to 15
th
order, The THD of Acuvim-DL is up to
25
th
.). Acuvim-EL and Acuvim-KLwill only display
voltage and current unbalance factor.
The 1
st
screen: Unbalance factor for voltage and
current.
As shown i n Fi g. 3- 32, vol t age unbal ance
factor=0.3%, current unbalance factor=0.5%.
Press H to go to the next screen.
Press H key to display voltage and current harmonic content. The HAR icon
will be shown on the top of the screen. The sequence will roll starting from the
2
nd
harmonic of voltage to the 15
th
harmonic of current as you press H each
time. The following shows the display for phase voltage, line to line voltage and
current harmonic contents.
Fig.3-31maximum system power demand
Fig.3-32 Unbalance factor for voltage
and current
ALUM0330
(603) 746-5524
(603) 746-5524
48
The 2
nd
screen: 2nd harmonic content of voltage.
As shown in Fig.3-33, U1_Hr2=0.12%,
U2_Hr2=0.14% , U3_Hr2=0.12%.
Press H to scroll through the 3rd to the 15th and
25thphase voltage harmonic content.
Note: When voltage wiring of the meter is set to
2LL or 3LL, line to line voltage harmonic contents
will be display instead (as shown in Fig. 3-34).
The 2
nd
screen: 2nd harmonic content of line to line
voltage.
As shown in Fig.3-34, U12_Hr2=0.12%, U23_
Hr2=0.14% , U31_Hr2=0.12%.
Press H to scroll through the 3
rd
to the 15
th
and 25
th
line to line voltage harmonic content.
The 16
th
/26
th
screen: 2nd harmonic content of
current.
As shown in Fig.3-35, I1_Hr2=3.08%, I2_Hr2=3.05%,
I3_Hr2=3.01%.
Press H key to scroll through the 3rd to the 15
th
and 25
th
current harmonic content.
In the statistic mode, press H and E simutaneously
to exit this mode.
Fig.3-33 2
nd
harmonic content of
phase voltage
ALUM0331
Fig.3-34 2
nd
harmonic content of line to
line voltage
ALUM0332
Fig.3-35 2
nd
harmonic content of
current
ALUM0333
(603) 746-5524
(603) 746-5524
49
3.4 System Parameter Setting
Press H and V/A simultaneously in the metering data display mode to enter
the system parameter setting mode. All the settings can be done through the
keys on the meter front panel.
Press H to move the flashing cursor to the right, press P to increase the
number by 1 once a time, press E to decrease the number by 1 once a time,
press V/A to accept the change and move to the next screen. Press H and V/
A simultaneously to exit system parameter setting mode and return to real-time
metering mode.
Note
Af t er s et t i ngs have
been modified for the
current page, press V/
A to store the current
value. Exiting the setting
mode by pressing H and
V/A simultaneously will
di scard any changes
made to the current page.
ALUM0334
Fig.3-36 Password input page
System parameter setting mode is password protected, a four digit password
(select from 0000 to 9999) is required everytime before accessing the system
parameter settings . The default password is 0000. After entering the password,
press V/A to accept the password and proceed . The meter will return to the
real-time metering mode if a wrong password is entered.
(603) 746-5524
(603) 746-5524
50
The 1
st
screen: Communication Address setting.
The address can be any integer between 1-247. As
shown in Fig.3-37, the communication address is 1.
To change the address, press H to move the
cursor, press P to increase value by 1, press E
to decrease value by 1. Press V/A to store the
current address and go to the next setting screen.
Press V/A to proceed to the next screen if there is
no need to change the address.
Note: Meters can not have the same communication address on the same RS485
communication line according to the Modbus-RTU protocol.
The 2
nd
screen: Baud rate setting.
The asynchronous communication setting of
Acuvim-L is 8 bit, parity, 1 start bit and 1 or 2 stop
bit. Baud rate can be set as follows: 1200, 2400,
4800, 9600, 19200, 38400. Press P or E to select
a suitable baud rate. Press V/A to accept the
change and proceed to the next screen. Same
baud rate should be used for all meter connecting
on the same communication line.
The 3
rd
screen: communication check setting.
communication check could be one of four
settings: non1, non2, odd, EVEN. As shown in
Fig.3-39: communication check is set to non1.
Press PorEto select a communication check
mode, press V/A to accept the change and
processed to the next page.
Fig.3-37 Communication address setting
ALUM0335
Fig.3-38 Baud rate setting
ALUM0336
ALUM0337
Fig.3-39 communication check
setting
(603) 746-5524
(603) 746-5524
51
Note: The page is only shown in Acuvim-EL and KL. non1 represents non-parity,
single stop bit; non2 represents non-parity, double stop bit; odd represents
odd-parity, single stop-bit; EVEN represents even parity, single stop bit. By
default it is set as EVEN.
The 4
th
screen: Voltage input wiring setting.
Voltage input could be one of four settings: 3LN,
2LN*, 2LL, 3LL.
As shown in Fig.3-40: voltage input mode is set to
3LN.
Press P or E to select a wiring mode, press V/A to
accept the change and proceed to the next page
Note: * wiring method not applicable to Acuvim-EL and Acuvim-KL
The 5th screen: Current input wiring setting.
Current wiring mode can be one of the three
settings: 3CT, 2CT*, 1CT*. As shown in Fig.3-41,
current input mode is set to 3CT
Press P or E to select a wiring mode, press V/
A to accept the change and proceed to the next
page.
The 6
th
screen: PT primary side ratio setting.
PT1 ratio can be set from 50.0 to 1,000,000.0 (unit
in V)
As shown in Fig.3-42, PT1=380.0V.
To change PT1 value, press H to move the
cursor, press P to increase value by 1, press E
to decrease value by 1. Press V/A to store the
current value and proceed to the next screen.
Fig.3-41 Current input wiring setting
ALUM0338
Fig.3-40 Voltage input wiring setting
ALUM0337
Fig.3-42 PT primary side ratio setting
ALUM0339
(603) 746-5524
(603) 746-5524
52
The 7
th
screen: PT secondary side ratio setting.
PT2 ratio can be set from 50.0 to 400.0 (unit in V).
As shown in Fig.3-43, PT2=380.0V.
To change PT2 value, press H to move the cursor,
press P to increase value by 1, press E to decrease
value by 1. Press V/A to store the current value
and proceed to the next screen.
Note: If no PT is installed at the voltage input, PT1 and PT2 should be the same
and equal to the input rated voltage.
The 8
th
screen: CT primary side ratio setting.
CT1 ratio can be set from 5 to 50000 (unit in A). For
a 1A option meter, CT1 can be set from 1 to 50000
(unit in A).
As shown in Fig.3-44, CT1=5A.
To change CT1 value, press H to move the cursor,
press P to increase value by 1, press E to decrease
value by 1. Press V/A to store the current value
and proceed to the next screen.
Note: CT1 has two digit lines representing one fgure. For example, if CT primary is
200, CT1 should be programmed as 0020 for the top line, and 0 for the bottom line, so
that it is read as 200.
Fig.3-43 PT secondary side ratio setting
ALUM0340
Fig.3-44 CT primary side ratio setting
ALUM0341
(603) 746-5524
(603) 746-5524
53
The 9
th
screen: CT secondary side ratio setting.
CT2 is a constant value of either 5 (standard) or 1
(1A option) (unit in A).
As shown in Fig. 3-45, CT1=5A, Press V/A to
proceed to the next page.
The 10
th
screen: Defnition of reactive power.
0: sinusoidal reactive power;
1: budeanus reactive power.
Pl ease refer to Chapter 3. 6 <<Measurement
methods and parameter defnitations>> for details.
The 11
th
screen: Backlight ON time setting.
The ON time can be set from 0 to 120 minute.
The LCD screen backlight will always be ON if
the setting value is 0. The backlight will turn OFF
afterinactive for a period of time if other value
(from 1to 120) is set.
As shown in Fig.3-47, the setting time of the
backl i ght i s 2 mi nutes. The backl i ght wi l l
automatically turn OFF if no key activation within
2 minutes.
Fig.3-45 CT secondary side ratio setting
ALUM0342
Fig.3-46 Defnition of reactive power
ALUM0343
Fig.3-47 Backlight ON time setting
ALUM0344
(603) 746-5524
(603) 746-5524
54
The 12
th
screen: Sliding windows time for demand
setting.
Sliding windows time of demand can be set from
1-30 minute. The window slides once per minute.
As shown in Fig.3-48, the sliding windows time is 8
minute.
The 13
th
screen: Clear Max and Min page setting.
To clear Max and Min values do not mean writing
0 to all of the registers. Meters current metering
values will be copied to the statistic registers
instead and start a new statistic period.
Press P or E to select YES or NO:
YES: clear Max and Min;
NO: do not clear Max and Min.
Press V/A accept selection and proceed to the
next page.
The 14
th
screen: Clear energy enable setting page.
This screen enables the energy reset function of
the meter.
1: enable; 0: disable.
Fig.3-48 Sliding windows time for
demand setting
ALUM0345
Fig.3-49 Clear Max and Min page setting
ALUM0346
Fig.3-50 Clear energy enable setting
ALUM0347
(603) 746-5524
(603) 746-5524
55
The 15
th
screen: Acknowledgement to clear energy
setting.
This screen appears only when the 14
th
screen is set
as enable.
Press E or P to select YES or NO:
YES: clear energy;
NO: do not clear energy.
All energy parameters will be set to 0 when YES is selected. Press V/A to accept
selection and proceed to the next page.
The 16
th
screen: Clear running time setting.
Press P or E to select YES or NO:
Yes: clear running time;
No: do not clear running time.
Running time will be set to 0 when YES is selected.
Press V/A to accept selection and proceed to the
next page.
The 17
th
screen: Clear load running time setting.
the page would display when Acuvim-DL, Acuvim-
EL and Acuvim-KL is selected. Press P or E to
select YES or NO: Yes: clear running time. No:
do not clear running time.Running time will be set
to 0 when YES is selected. PressV/A to accept
selection and proceed to next page.

Fig.3-51 Acknowledgement to clear
energy setting
ALUM0348
Fig.3-52 Clear running time setting
ALUM0349
Fig.3-53 Clear load running time setting
(603) 746-5524
(603) 746-5524
56
The 18
th
screen: VAR/PF setting. if the left screen
show 0, the display of power load character as
IEC. if the left screen show 1, the display of
power load character as IEEE. As show in Fig.3-54
the display of power load character as IEC. press
P or E to select 1 or 0.Fig.3-54 VAR/PF setting
Note: The page would be show only in Acuvim-EL.
The 19
th
screen: Password setting.
This is the last screen in system parameter setting
mode. The password can be changed in this page.
It is important to remember the new password.
As shown in Fig.3-55, the password is 0001. Press
V/A to store the new password and return to the
frst setting page. Press H and V/A together to
exit the system setting mode after fnishing all of
the settings.
3.5 DO Parameter Setting and Expansion Module Setting
Acuvim-BL meter has two digital outputs. Each can operate as energy pulse
output or alarm output. All DO parameters can be set from the meter front. To
distinguish with system parameter setting mode, we call this setting mode as DO
parameter setting mode.
Press P key and E key simutaneously under system parameter setting mode to
enter DO parameter setting mode. Press H to move the fashing cursor to the
right, press P to increase the number by 1 once a time, press E to decrease the
number by 1 once a time, press V/A to accept the change and move to the next
screen. Press P and E simultaneously to exit DO parameter setting mode and
return to system parameter setting mode.
Fig.3-54 VAR/PF setting
Fig.3-55 Password setting
ALUM0350
(603) 746-5524
(603) 746-5524
57
I f the extend I O modul e coul d be added, i t contai ns 2 DO, 4 DI and
communi cati on wi th Modbus-RTU standard. Press P key and E key
simutaneously under system parameter setting mode to enter DO parameter
setting and Extend IO communication setting mode, the operation about key is
same as Acuvim-BL DO setting.The following steps show how to set DO items:
The 1
st
screen: Extend IO baud rate setting.
Extend IO Baud rate can be set as follows: 1200,
2400,4800, 9600, 19200, 38400. Press P or E to
select a suitable baud rate. Press V/A to accept
the change and proceed to the next screen.
Same baud rate should be used for all meters
connecting on the same communication line.
Note: The page would be shown only in Acuvim-
DL and Acuvim-EL.
The 2
nd
screen: Extend IO communication check
setting. Extend IO communication check could
be one of four settings: NON1,NON2,odd,EVEN.
As shown in Fig.3-57: Extend IO communication
check is set to NON1.
Press PorEto select a communication check
mode, press V/A to accept the change and
processed to the next page.
Note: The page would be shown only in Acuvim-EL.
ALUM0350
Fig.3-56 Extend IO baud rate setting
ALUM0351
Fig.3-57 Extend IO communication
check setting
(603) 746-5524
(603) 746-5524
58
The 3
th
screen: DO1 output mode setting.
0: pulse output; 1: alarm output. As shown in Fig.3-
58, DO1 is set as pulse output mode.
Press V/A to accept change and proceed to the
next page.
The 4
th
screen: DO2 output mode setting.
0: pulse output; 1: alarm output. As shown in Fig.3-
59, DO2 is set as alarm output mode.
next page
The 5
th
screen: DO pulse constant rate setting.
Pulse constant rate indicates the energy value
(kWh, kvarh) per pulse. Pulse constant can be set
from any interger from 1 to 6000. Each unit stands
for 0.1kWh or 0.1kvarh.
As shown in Fig.3-60, pulse constant is 1 (meaning
1 pulse for every 0.1kWh or 0.1kvarh)
next page
Fig.3-58 DO1 output mode setting
ALUM0351
Fig.3-59 DO2 output mode setting
ALUM0352
Fig.3-60 DO pulse constant rate setting
ALUM0353
(603) 746-5524
(603) 746-5524
59
The 6
th
screen: DO pulse width setting.
DO pulse width can be set from any integer from
1 to 50. Each unit stands for 20ms.
As shown in Fig.3-61, the pulse width is set to 5,
that is 520=100ms.
next page.
The7
th
screen: DO1 output item setting.
The DO1 output can be one of the following
energy items shown in table below:
As shown in Fig.3-62, pulse output is enabled.
next page.
The 8
th
screen: DO2 output item setting.
Same as DO1 output item setting, refer to the
energy item selection table shown above.
DO1 and DO2 settings are independent of each
other.
Press V/A key for acknowledgement and go to the
next page.
Fig.3-63 DO2 output item setting
ALUM0356
Fig.3-61 DO pulse width setting
Fig.3-62 DO1 output items setting
ALUM0355
ALUM0354
Item value 0 1 2 3 4
Energy select No output Ep_imp Ep_exp Eq_imp Eq_exp
(603) 746-5524
(603) 746-5524
60
The 9
th
screen: DO delay time for alarm setting.
If alarm condition lasts for over the preset time
period, the alarm signal will be triggered. The
delay time can be set from any integer from 0 to
255. Each unit stands for 300ms.
The10
th
screen: DO1 alarm output item setting.
The DO1 alarm output can be one of the following
energy items shown in table below:
As shown in Fig.3-65, DO1 alarm parameter is 06,
tracking object is V31
next page.
Fig.3-64 DO delay time for alarm setting
Fig.3-65 DO1 alarm output items setting
ALUM0358
ALUM0357
Var 0 1 2 3 4 5 6 7 8
Item Hz V1 V2 V3 V12 V23 V31 I1 I2
Var 9 10 11 12 13 14 15 16 17
Item I3 In P1 P2 P3 Psum Q1 Q2 Q3
Var 18 19 20 21 22 23 24 25 26
Item Qsum Ssum PF1 PF2 PF3 PFsum U_unbl I_unbl Dmd_P
Var 27 28 29 30 31 32 33 34
Item Dmd_Q Dmd_I1 Dmd_I2 Dmd_I3 S1 S2 S3 Dmd_S
(603) 746-5524
(603) 746-5524
61
The 11
th
screen: DO1 inequality sign setting.
0: < (less than); 1: > (greater than)
As shown in Fig.3-66, the inequality sign is set to 1,
which means when the tracking value is above the
preset limit, an alarm output will be triggered.
next page.
The 12
th
screen: DO1 alarm limit setting.
Set the alarming limit value for the tracking
parameter.
As shown in Fig.3-67, the DO1 limit is set to 1800.
Refer to Chapter 3.8 << Measurement Methods
and Parameter Definitations>> for alarm limit
value setting details.
next page.
The 13
th
screen: DO2 alarm output item setting.
Same as DO1 alarm output item setting, refer
to the alarm output item selection table shown
above.
As shown in Fig.3-68, DO2 alarm parameter is 08,
tracking object is Phase 2 current.
next page.
Fig.3-68 DO2 alarm output item setting
ALUM0361
Fig.3-67 DO1 alarm limit setting
ALUM0360
Fig.3-66 DO1 inequality sign setting
ALUM0359
(603) 746-5524
(603) 746-5524
62
The 14
th
screen: DO2 inequality sign setting.
0: < (less than); 1: > (greater than)
next page.
The 15
th
screen: DO2 alarm limit setting.
Set the alarming limit value for the tracking
parameter.
Refer to Chapter 3.8 << Measurement Methods
and Parameter Definitations>> for alarm limit
value setting details.
As shown in Fig.3-70, the DO2 limit is set to 4500.
This is the last screen of DO parameter setting.
The 16
th
screen: backlight blinking setting. If the
alarm backlight blinking is enabled, the screen
displays 1. As show in Fig.3-71, the backlight
blinkingis enabled. Under this circumstance, when
an alarm is triggered, the backlight will be blinking
at the same time. Press P or E to choose between
0 and 1.
Fig.3-69 DO2 inequality sign setting
Fig.3-70 DO2 alarm limit setting
ALUM0363
ALUM0362
Fig.3-71 alarm back light blink setting
(603) 746-5524
(603) 746-5524
63
The 17
th
screen: PROFIBUS address setting page.
PROFIBUS address can be set from 0~126, this
page will display if the power meter connect a
PROFIBUS module.
PROFIBUS address can be set only via key, and it
valid right now after modifed.
3.6 DI status Display function
Acuvim-DL and Acuvim-EL support display of 4 extend DI status. Press H +
Pcan enter or exit DI status display. The pages can be turned by pressing V/A.
From Fig. 3-73 to Fig. 3-76, it shows that all of the 4 DIs status are OFF.
The 1
st
screen: DI1 current status display. if DI1
status is turn on, the screen will display ON. if
DI1 status is turn of, the screen will display OFF.
As show in Fig.3-73, DI1 ststus is turn of.
The 2
nd
ALUM0365
Fig.3-73 DI1 status display
ALUM0366
Fig.3-72 PROFIBUS address setting
(603) 746-5524
(603) 746-5524
64
The 3
th
The 4
th
status is turn on, the screen will display ON. if DI4
status is turn of, the screen will display OFF. As
show in Fig.3-76, DI4 ststus is turn of.
3.7 TOU Energy and Maximum Demand Display
Press V/A and Esimultanelously to enter the TOU Energy and maximum
demand page. Press E to display TOU Energy. Press P to display TOU Maximum
Demand. Press H to change the tariffs page. it could display energy under
diferent tarifs in Maximum Demand page. it could also display demand under
diferent tarifs in maximum demang page. Press V/A and E simultanelously
to exit to real-time metering mode.
On the top of the display page, "TOU" represents Time of Use related parameters;
"0" represents the total tariff; "1" indicates the represents Time of Use; "2"
indicates peak tarif; "3" indicates the valley tarif; "4" indicates thenormal tarif.
Press E to display the energy under diferent tarifs, as described below.
ALUM0367
ALUM0368
(603) 746-5524
(603) 746-5524
65
The 1
st
screen: Total tarif import energy. As shown
in Fig.3-77, Ep_Imp=1152.8kWh. Press V/A to
turn to the next screen.
The 2
nd
screen: Total tariff export energy. As
shown in Fig.3-78, Ep_ Exp=203.8kWh. Press V/A
to turn to the next screen.
The 3
rd
screen: Total tarif import reactive energy.
As shown in Fig.3-79, Eq_ Imp=3025.8 kvarh.Press
V/A to turn to the next screen.
Fig.3-77 Total tarif import energy
Fig.3-78 Total tarif export energy
Fig.3-79 Total tarif import reactive energy
(603) 746-5524
(603) 746-5524
66
The 4
th
screen: Total tariff export reactive energy.
As shown in Fig.3-80, Eq_ Exp=7142.6 kvarh.Press
The 5
th
screen: Total tarif apparent energy of TOU.
As shown in Fig.3-81, Es=1879.8 kVAh.Press V/
A return to 1st screen, then press H turn to 6th
screen.
In the same way, press V/A key to switch the
screen under the same tarifs.
Press H will switch the screen under the diferent
tarifs.
Press P would display the maximum demand under each tariff in the TOU
energy screen, The following paragraphs introduce Maximumm Demand in
details.
The 1
st
screen: Total tari ff maxi mum power
demand. As shown in Fig.3-82, P1 = 12.68 kW, P2 =
21.32 kvar, P3 = 30.43 kVA. Press V/A to go to the
next screen.
Fig.3-80 Total tarif export reactive energy
Fig.3-81 Total tarif apparent energy
Fig.3-82 Total tarif maximum power
demand
(603) 746-5524
(603) 746-5524
67
The 2
nd
screen: Total tariff maximum current
demand. As shown in Fig. 3-83, I1 =10.12kA,I2 =
10.10kA, I3 = 10.09 kA, Press V/A to switch the
screen between maximum power demand and
maximum current demand.
Press H to switch the screen under the diferent
tarifs.
3.8 Acuvim-L Measurement Methods and Parameter Defnitions
Almost all the electric parameters in power systems can be measured by the
Acuvim-L series meter. The following section introduces those parameters in
more details.
Voltage (U): True RMS value of three phase voltages, three line to line voltages
is measured and displayed in the Acuvim-L series meter.
Current (I): True RMS value of three phase current, neutral current is measured
and displayed in the Acuvim-L series meter.
Power (P): Three phase power and total system power are measured and
displayed in the Acuvim-L series meter.
Reactive power (Q): Acuvim-L series meter uses the following two methods for
reactive power calculation.
1. Sinusoidal reactive power. The formula is as follows:
2 2 2 2
P S D Q = +
Fig.3-83 Total tarif maximum current
demand
(603) 746-5524
(603) 746-5524
68
2. Nonsinusoidal reactive power. The formula is as follows:
Where Q D: Budeanus distortion power.
Q: Budeanus reactive power.
Apparent power (S): Three phase apparent power and total system apparent
power are measured and displayed in the Acuvim-L series meter.
Power factor (PF): Three phase power factor and total system power factor are
measured and displayed in the Acuvim-L series meter.
Frequency (F): The frequency of V1 phase voltage input is measured as system
frequency.
Energy (kWh): Energy is time integral of power. The unit is kWh. Since power
is measured in bi-direction, positive means importing and negative means
exporting, energy is also expressed according to the power direction.
Import energy (Ep_imp): Energy imports from a source.
Export energy (Ep_exp): Energy exports to a load.
Reactive energy (kvarh): reactive energy is time integral of reactive power. The
unit is kvarh. Since reactive power is measured in bi-direction, positive means
inductive and negative means capacitive, reactive energy is also expressed
according to the load nature.
Import reactive energy (Eq_imp): inductive energy.
Export reactive energy (Eq_exp): capacitive energy.
Apparent energy: apparent energy is time integral of apparent power. The unit
2 2 '
D Q Q + =
(603) 746-5524
(603) 746-5524
69
is kVAh.
Harmonic parameter (not available for Acuvim-EL):
Total harmonic distortion: this factor is often used to express the power quality
of the power system. The formula is as follows:
In the formula, U1 is Rms value of the voltage fundamental and Uh is Rms value of
the voltage harmonic with order n.
Each harmonic rate: the percentage of each harmonic is divided by the
fundamental.
Demand: real power demand, reactive power demand, total system power
demand, and three phase current demand can be measured with the Acuvim-L
series meter. The meter uses sliding window method for demand calculation.
Demand interval can be selected from 1 to 30 minutes. Demand window slides
one minute each time. For example, the demand interval is set as 3 minutes. If
the total power of the 1
st
minute is 12, the 2
nd
minute is 14 and the 3
rd
minute
is 10, the total power demand of the 3 minutes is (12+14+10)/3=12. If another
minute passed by (the 4
th
minute) and the total power for the minute is 9, the
total power demand after 4 minutes, according to the 3 minute interval, should
be (14+10+9)/3 = 11.
% 100
50
2
2
1

=

= h
h
U
U
THD
% 100
1
=
I
I
HRI
h
h
% 100
1
=
U
U
HRU
h
h
(603) 746-5524
(603) 746-5524
70
Max/Min: Acuvim-L series meter can measure the max value of real system
power, reactive power and apparent power and the max/min of the three phase
voltage and current. The data is stored in non-volatile memory and can be
accessed or cleared via meter front or communication.
Unbalance factor: Acuvim-L series meter can measure unbalance factor of
three phase voltage and current using sequence vector method. For Acuvim-
AL, Acuvim-BL , Acuvim-CL and Acuvim-DL, the formula of voltage and current
unbalance factor as follows:
Voltage unbalance factor = (RMS value of V1 (V12) negative component of the
fundemental wave / RMS value of V1 (V12) positive component of fundemenal
wave) x 100 %
Current unbalance factor = (RMS value of I1 negative component of the
fundemental wave / RMS value of I1 positive component of fundemenal wave) x
100 %
For Acuvim-EL, the formula of voltage and current unbalance factor as follows:
Voltage unbalance factor = Maximum diference of phase voltage / average of
phase voltage OR Voltage unbalance factor = Maximum diference of line to line
voltage / average of line to line voltage
Current unbalance factor = Maximum diference of phase current / average of
phase current
Energy measurement: The energy measurement type include real time energy
measurement and time of use (Acuvim-EL only) energy measurement. The
function is described as follows:
Real time energy: the accumulation of energy for the kWh, kvarh and kVAh since
(603) 746-5524
(603) 746-5524
71
cleared last time. The real time energy includes each single-phase energy, which
could be useful for observing the increment of single-phase energy.
Time of use (TOU): User can assign up to 4 diferent tarifs (sharp, peak, valley
and normal) to different time period within a day according to the billing
requirements. The meter will calculate and accumulate energy to diferent tarifs
according to the meters internal clock timing and TOU settings.
TOU setting: User can set a maximum of 12 TOU seasons, each season can be
assigned to a TOU schedule (a maximum of 14 TOU schedules are available). Each
schedule can be divided up into 14 segments (in which each segment can have
its own tarif).
User can customize the TOU calendar (including its tariffs, seasons, schedules
and segments) according to diferent applications. To make sure that the TOU
calendar is setup correctly, the meter will check the TOU settings according to
the predefned rules (see below for TOU setting format requirement for details).
TOU function will be disabled if the TOU calendar is set up incorrectly. If no
errors are found in the calendar and the TOU function is enabled, TOU energy
accumulation will begin.
(603) 746-5524
(603) 746-5524
72
TOU setting format requirement:
1. Season setting parameter: The calendar year will be divided up into diferent
seasons depending on the season setting parameter. The parameter can be
selected from any integer between 1 to 12. User must enter the correct value
for the season setting parameter in accordance to the TOU season table. If the
season setting parameter is set as 2, the frst 2 slots of the TOU season table must
be set, otherwise it will be considered as an invalid input (TOU function will be
disabled).
2. TOU season format: Enter the start date into the TOU season table slot
following this format MM-DD ID - MM stands for the month, DD stands for the
day and ID stands for the TOU schedule ID (available from 01 to 14). The dates
should be organized so that they are in sequence according to the calendar
year (the earlier date comes frst and the later date comes last). For example, if 3
seasons are selected, the date parameters are January 1, June 6 and September 7,
and TOU schedule 02, 01, 03 will be used respectively, the frst TOU season table
slot shall enter 01-01 02, the second slot shall enter 06-06 01, and the third slot
shall enter 09-07 03. Entering 01-01 02 for the frst slot, 09-07 03 for the second
slot and 06-06 01 for the third slot is considered invalid.
3. Schedule setting parameter: The number of available TOU schedules
depends on the schedule setting parameter. The parameter can be selected
from any integer between 1 to 14. This parameter determines the number of
TOU schedules available for the TOU calendar setting. A maximum of 14 TOU
schedules (from TOU Schedule #1 to TOU Schedule #14) can be used.
4. Segment setting parameter: Each TOU schedule consists of various timing
segments. The number of segments depends on the segment setting parameter
setup. The parameter can be selected from any integer between 1 to 14
(inclusively). User must enter the correct value for the segment setting parameter
(603) 746-5524
(603) 746-5524
73
in accordance to the TOU schedule table. If the segment setting parameter is set
as 3, the frst 3 slots of the TOU schedule table must be set, otherwise, it will be
considered as an invalid input (TOU function will be disabled).
5. TOU schedule format: Each TOU schedule represents a 24 hour cycle. Similar
to TOU season format, enter the start time into the TOU schedule table slot
following this format HH:MM ID - HH stands for hour (in 24 hr format), MM
stands for minutes and ID stands for tarifs (available from 00 to 03). The time
should be organized according to the hour sequence. For example, if 3 segments
are selected, timing parameters are 01:00, 15:30, 22:45, the order of the 3
segments should be one of the following: 01:00, 15:30, 22:45 or 15:30, 22:45,
01:00 or 22:45, 01:00, 15:30 Entering time information in a wrong sequence (for
example, entering 15:30, 01:00, 22:45) is considered as an invalid operation, TOU
function will be disabled.
6. Tarif setting parameter: This parameter corresponds to the number of tarifs
available for the TOU calendar and can be selected from any integer from 0 to 3.
The four tarifs: sharp, peak, valley and normal are represented by 4 integers: 0,
1, 2 and 3 respectively. If the tarif setting parameter is set to 3, all of the 4 tarifs
will be available for the TOU calendar; if the parameter is set to 1, only the frst 2
tarifs (sharp and peak) will be available.
7. Holiday setting parameter: This parameter can be set from any integer
between 1 and 30, meaning a maximum of 30 holidays can be programmed to
the TOU calendar. If the holiday setting parameter is set as 3, the frst 3 slots of
the holiday schedule must be set, otherwise it will be considered as an invalid
input (TOU function will be disabled).
Note: User can either customize the TOU calendar factory settings or use the
default factory settings. User can reset the TOU calendar to its default value
either via communication or from the meter front.
(603) 746-5524
(603) 746-5524
74
8. Holiday schedule: The holiday schedule uses the same format as the TOU
seasons MM-DD ID. User can select which TOU schedule to be used for the
holiday. The dates of the holiday schedule do not need to be organized in
a sequential order (i.e. the first slot can be January 1, the second slot can be
December 26 and the third slot can be December 25).
9. Daylight saving time(DST): under the circumstance that DST is enabled, if you
choose the fxed date option, you set a fxed date for DST, the format is month
/ day / hour / minute / adjust the time (in minute ). If you choose the non-fxed
data option, you set a day in a week for DST, the format is month / which week/
day / hour /minute / adjust time (in minute). Once DST is enabled, DST will be
automatically implemented by the chosen option.
When the clock startes to run DST, the meter will automatically adjust the clock
for a settable time period in advance. When the clock runs to the end of DST, the
meter will automatically adjust the clock back for a settable time period.
(603) 746-5524
(603) 746-5524
75
Fig.3-84 DST setting interface
(603) 746-5524
(603) 746-5524
76
10.Holidays preset function: Ten years holiday setting
In this setting, users can program holidays in the future decade. The format is
month / day / year, holiday code.
When Enable Holiday Years Settings is checked, users can click Make Holiday
Settings (10 Year) to enter the holiday table setup page. Once the setup is done,
users can click Generate, by which a holiday table for the next decade can be
generated. Figure 3-84 depicts a ten year holiday table.
Fig.3-85 ten years holiday table
(603) 746-5524
(603) 746-5524
77
11. Weekend Schedule: Weekend Setting (bit0 : Sunday; bit1 ~ bit6: Monday to
Saturday; bit 0 means not effective, bit 1 means effective). For example, when
the Weekend Setting bit0 is 1, it means Sunday is efective. When the Weekend
Setting bit1 is 1, it means Monday is efective. For example, if a user wants to set
Saturday and Sunday effective, he should put 65 (1000001) into the Weekend
Setting feld. When the meter clock is within the preset Weekend Schedule, the
energy will accumulate under the tarif that corresponds to the Schedule.
Note: Holiday schedule has the highest priority among all the schedules followed
by the Weekend Schedule. That is, when set appropriately, holiday and weekend
schedules override normal (weekday) TOU settings. When a holday falls in a
weekend, the holiday schedule overrides the Weekend Schedule.
Record and Clear of Maximum Demand
Acuvim-EL could record the maximum power and current demand under
diferent tarifs, when the TOU Function is enabled and the setting of time table is
correct. It also can clear the value under diferent tarifs.
There are two ways of resetting Current Month TOU:
1. End of Month: This is the default method. All values from Current Month TOU
will be copied over to Prior Month TOU at the very beginning of each month (the
frst day of each month at time 00:00:00). Current Month TOU will be cleared and
reset to 0.
2. Assign: User can select when should the values from Current Month TOU be
copied over to Prior Month TOU. User can set the time in the following format
DD HH:MM:SS - DD stands for day, HH stands for hour, MM stands for minute, SS
stands for second. Similar to the previous method, once Current Month TOU is
transferred to Prior Month TOU, all values from Current Month TOU will be cleared
and reset to 0.
(603) 746-5524
(603) 746-5524
78
Over/Under limit alarming: Acuvim-BL has over/under limit alarming capability.
if you want to learn more please read the introduction of extend IO function
chapter.
Energy Pulse Output: The two digital outputs (DOs) from the Acuvim-BL can be
used as energy pulse output.
Introduction of extend IO function: As shown in Fig.3-85 extended IO
parameter setting, it includes DO type, DI type and Communication settings.
(603) 746-5524
(603) 746-5524
79
Fig.3-86 Extend IO parameter setting
(603) 746-5524
(603) 746-5524
80
Extension IO communication:
Acuvim-EL and Acuvim-DL extended IO module supports RS485 communications
with Modbus-RTU protocol, the extended module share the same device address
and it supports six baud rate: 1200, 2400, 4800, 9600, 19200, 38400, as well
as different parity selections. The setting of baud rate and parity check can
implement by software and meter display screen. It can be be implemented
by software or from the meter front. The instrument can be connected with the
PROFIBUS communication module at the same time. For detailed content, please
refer to Acuvim-L Profbus Modules Users Manual.
Digital output (DO)
As shown in Fig.3-85, the DO type includes alarm output and energy pulse
output. DO type can be set via software as well.
Over/Under limit alarming:
Acuvim-BL, Acuvim-DL and Acuvim-EL has over/under limit alarming capability.
When the monitored parameter goes beyond/below the preset limit and stays
at the level over the preset amount of time delay, the over/under limit alarm will
be triggered. The meter LCD screen backlight will fash and the corresponding
digital output (DO) will be activated until the parameter condition returns to
normal. Upon alarming, DO can be used to activate devices such as safety beacon
light and buzzer. Each DO supports 1 alarming parameter. An over/under limit
alarming example is shown below.
For example:
Alarming Condition: when Phase B current goes above 180A (CT ratio is set as
200:5) for over 15 seconds, over limit alarm will be triggered, alarm signal will be
set out via DO1. Setting procedures should be as follows: Enter DO parameter
setting mode by pressing P and E simutaneously under system parameter
setting mode.
(603) 746-5524
(603) 746-5524
81
1) Set DO1 mode to 1 (alarm output)
2) Set delay time to 50 (the base unit of delay time is 300ms, the setting value
should be 15/0.3=50)
3) Set alarming parameter to 8 (tracking object for parameter 8 isPhase B
current))
4) Set inequality sign to 1 (greater than)
5) Set alarm value to 4500 (according to Table 4-9. Conversion relationship of
basic measurements from Chapter 4.4 <<Data address table of Acuvim-L>>,
the setting relationship is I=Rx*(CT1/CT2)/1000, Rx=4500) Press V/A to accept
change then press P and E simutaneously to exit DO parameter setting mode.
Energy Pulse Output:
Acuvim-BL, Acuvim-DL and Acuvim-EL has Energy pulse output function. Each
energy pulse output channel can be set to monitor one of the four energy
parameters (Ep_imp, Ep_exp, Eq_imp or Eq_exp). Pulse constant and pulse
with can also be set according to users requirement. Pulse constant stands
for amount of energy (kWh or kvarh) per pulse; pulse width stands for the time
duration for each pulse. DO will send out a pulse signal when the accumulated
energy reaches the pulse constant value. Related parameters: pulse energy
output ranges from 0 to 4 corresponding to none, Ep_imp, Ep_exp, Eq_imp,
Eq_exp. Pulse constant ranges from 1 to 6000 (word) with a unit of 0.1kWh
(kvarh). Pulse constant relates to the resolution of the energy output. Pulse
width ranges from 1 to 50 (word) with a unit of 20ms. The shortest interval
between two pulses is 20ms.In practice the pulse width and the pulse ratio are
selected according to system power. The relation of the two parameters should
satisfed following expression:pulse ratio >[(pulse width +1)Pmax]18000 In the
expression, the Pmax is the maximum power or reactive power. The unit is kW
(603) 746-5524
(603) 746-5524
82
or kvar. Recommend pulse ratio is 3 to 5 times the right side value of the above
expression.
Digital Input (DI)
Fig.3-87 SOE record display
(603) 746-5524
(603) 746-5524
83
(1) DI function introduction:
The DI type can be set as shown in Fig.3-85 Extend IO parameter setting.
If SOE record function is selected, the DI will work as SOE state mode as shown
Fig. 3-86 SOE record display; if the counter is selected, the DI will work as input
pulse accumulation mode as shown in Fig.3-87 DI count and status display.
(2) SOE (Sequence of Event) function:
1) At present, the event allows the cycle of 20 SOE recording. When DI is in SOE
state mode, once the DI input level changes occur, an SOE event will be recorded.
In this way, it will achieve 20 SOE event loop recording. The event format: Year,
Month, Day, Minute, Seconds, Millisecond, DI status.
2) SOE function judges the single read event value. When a single event is
read, if the value is not the latest event in the log, it reads this single event and
the record number will be increased. If a record is the latest event, the incident
remains unchanged. The previous events can be read by the record numbers.
Fig.3-88 DI counter and status display
(603) 746-5524
(603) 746-5524
84
event be read, if the value is not currently reading the latest value of the event
log, it reads the current single event and the record number will be incremental,
if current reading record number is the latest event record number, a single
incident remain unchanged. by re-written a single event number, the user can
implement the previous event re-read.
(3) Pulse Counter function:
When the DI type is set to Pulse Counter, corresponding to the accumulated
pulse constant value, it achieves the cumulative function of DI input pulses. If
pulse constant is 1, DI input receives 1 input signal then cumulative pulse amount
adds 1. If pulse constant is 10, DI input receives 10 pulses then cumulative pulse
amount adds 1.
(603) 746-5524
(603) 746-5524
4.1 Modbus Protocol Introduction
4.2 Modbus Protocol
4.3 Communication Format
4.4 Data Address Table
Chapter 4 Communication
(603) 746-5524
(603) 746-5524
86
This chapter will mainly discuss how to operate the meter via communication
port using software. To master this chapter, you should be familiar with Modbus
and read other chapters of this manual to make sure that you have a good
understanding of the functions and applications of this product.
This chapter includes: Modbus protocol, format of communication and data
address table and Acuvim-L application details.
4.1 Modbus Protocol Introduction
Modbus
TM
RTU protocol is used for communication in Acuvim-L series meter.
Data format and error check methods are defined in Modbus protocol. The
half duplex query and respond mode is adopted in Modbus protocol. There is
only one master device in the communication net. The others are slave devices,
waiting for the query of the master.
Transmission mode
The mode of transmission defnes the data structure within a frame and the rules
used to transmit data. The mode is defned in the following which is compatible
with Modbus RTU Mode*.
* Modbus is trademark of Modicon, Inc.
Coding system 8-bit binary
Start bit 1
Data bits 8
Parity
Acuvim-AL/BL/CL/DL: no parity;
Acuvim-EL/KL: NON1/NON2/Odd/EVEN
Stop bit 1 or 2
Error checking CRC check
(603) 746-5524
(603) 746-5524
87
4.2 Modbus Protocol
Framing
Table 4-1 data frame format
Address feld
The address field of a message frame contains eight bits. Valid slave device
addresses are in the range of 0~247 decimal. A master addresses a slave by
placing the slave address in the address feld of the message. When the slave
sends its response, it places its own address in this address feld of the response
to let the master know which slave is responding.
Function feld
The function code feld of a message frame contains eight bits. Valid codes are
in the range of 1~255 decimal. When a message is sent from a master to a slave
device the function code feld tells the slave what kind of action to perform.
Address Function Data Check
8-bit 8-bit N8-bit 16-bit
Code Meaning Action
01 Read Relay Output Status Obtain current status of Relay Output
02 Read Digital Input(DI) Status Obtain current status of Digital Input
03 Read data
Obtain current binary value from one
or more registers
16 Preset multiple-registers
Place specifc value into a series of
consecutive multiple-registers
Table 4-2 Function code
(603) 746-5524
(603) 746-5524
88
Data feld
The data feld is constructed using sets of two hexadecimal digits, in the range
of 00 to FF hexadecimal. The data feld of messages sent from a master to slave
devices contains additional information which the slave must use to take the
action defined by the function code. This can include items like discrete and
register addresses, the quantity of items to be handled, and the count of actual
data bytes in the field. For example, if the master requests a slave to read a
group of holding registers (function code 03), the data feld specifes the starting
register and how many registers are to be read. If the master writes to a group of
registers in the slave (function code 10 hexadecimal), the data feld specifes the
starting register, how many registers to write, the count of data bytes to follow in
the data feld, and the data to be written into the registers.
If no error occurs, the data feld of a response from a slave to a master contains
the data requested. If an error occurs, the feld contains an exception code that
the master application can use to determine the next action to be taken. The
data feld can be nonexistent (of zero length) in certain kinds of messages.
Error Check Field
Every message includes an error checking field which is based on the Cyclical
Redundancy Check (CRC) method. The CRC field checks the contents of the
entire message. It is applied regardless of any parity check method used for the
individual characters of the message. The CRC feld is two bytes long, containing
a 16-bit binary value. The CRC value is calculated by the transmitting device, and
is appended to the message.
The receiving device recalculates the CRC value during reception of the message,
and compares the calculated value to the actual value it received in the CRC feld.
An error will be reported if the two values are not equal. CRC calculation is frst
started by preloading the whole 16-bit register to 1s. The process begins
(603) 746-5524
(603) 746-5524
89
by applying successive 8-bit bytes of the message to the current contents of the
register. Only the eight bits of data in each character are used for generating the
CRC. Start and stop bits, and the parity bit, do not apply to the CRC.
When generating the CRC, each 8-bit character is exclusive ORed with the
register contents. The result is shifted towards the least signifcant bit (LSB), with
a zero flled into the most signifcant bit (MSB) position. The LSB is extracted and
examined, if the LSB equals to 1, the register is exclusive ORed with a preset, fxed
value; if the LSB equals to 0, no action will be taken. This process is repeated until
eight shifts have been performed. After the last (eighth) shift, the next 8-bit byte
is exclusive ORed with the registers current value, and the process repeats for
eight more shifts as described above. The fnal contents of the register, after all
the bytes of the message have been applied, is the CRC value. When the CRC is
appended to the message, the low-order byte is appended frst, followed by the
high-order byte.
4.3 Communication Format
Explanation of frame
Table 4-3 Explanation of a frame
As shown in table 4-3 the meaning of each abbreviated word is:
Addr: Address of slave device
Fun: Function code
Data start reg HI: Start register address high byte
Data start reg LO: Start register address low byte
Data #of reg HI: Number of register high byte
Data #of reg LO: Number of register low byte
Addr Fun Data start
reg HI
Data start
reg LO
Data #of
regs HI
Data #of
regs LO
CRC16
HI
CRC16
LO
06H 03H 00H 00H 00H 21H 84H 65H
(603) 746-5524
(603) 746-5524
90
CRC16 HI: CRC high byte
CRC16 LO: CRC low byte
Chapter4 Communication
1. Read Status of Relay (Function Code 01)
This function code is used to read status in Acuvim-EL.1=On, 0=Of;
There are 2 Relays in Acuvim-DL/EL. The Address of each Relay is Relay1=0000H
and Relay2=0001H.
The following query is to read Relay Status of Acuvim-EL Number 17.
Query
Addr Fun
Relay
start reg
hi
Relay
start reg
lo
Relay # of
reg hi
Relay # of
reg lo
CRC16
Hi
CRC16
Lo
11H 01H 00H 00H 00H 02H BFH 5BH
Response
The Acuvim-DL/EL response includes the Acuvim-DL/EL address, function code,
quantity of data byte, the data, and error checking. An example response to read
the status of Relay1 and Relay2 is shown as Table4-5 The status of Relay1 and
Relay2 are responding to the last 2 bits of the data.
Relay1:bit0 Relay2:bit1
Addr Fun Byte count Data CRC16 Hi CRC16 Lo
11H 01H 01H 02H BFH 5BH
Table 4-4 Read the status of Relay1 and Relay2 Query Message
Table4-5 Relay status Response
(603) 746-5524
(603) 746-5524
91
The content of the data is:
7 6 5 4 3 2 1 0
0 0 0 0 0 0 1 0
MSB LSB
(Relay 1 = OFF , Relay 2=ON)
2. Read the status of DI(Function 02)
Function Code 02
1=On 0=Of
DI1s address is 0x0000, DI2s address is 0x0001, and so on.
The following query is to read the Status of 4 DIs of Acuvim-DL/EL with the
address of 17.
Query
Addr Fun
DI start
addr hi
DI start
addr lo
DI num
hi
DI num
lo
CRC16
Hi
CRC16
Lo
11H 02H 00H 00H 00H 04H 7BH 59H
Response:
The Acuvim-DL/EL response includes the Acuvim-DL/EL address, function code,
quantity of data characters, the data characters, and error checking. An example
response to read the status of 4 DIs are shown as Table 4-7 The status of 4 DIs are
responding to the last 4 bits of the data.
Table 4-6 Read 4 DIs Query Message
(603) 746-5524
(603) 746-5524
92
DI1: bit0; DI2: bit1; DI3: bit2; DI4: bit3.
Addr Fun Byte count Data CRC16 Hi CRC16 Lo
11H 01H 01H 03H E5H 49H
0 0 0 0 DI4 DI3 DI2 DI1
0 0 0 0 0 0 1 1
MSB LSB
3. Read Data (Function Code 03)
Query
This function allows the master to obtain the measurement results from the
Acuvim-L series meter. Table 4-8 is an example to read the 3 measured data (F, V1
and V2) from slave device number 17, the data address of F is 0130H, V1 is 0131H
and V2 is 0132H.
Addr Fun
Data start
addr HI
Data start
Addr LO
Data #of
Regs HIi
Data #of
Regs LO
CRC16
Hi
CRC16
Lo
11H 03H 01H 30H 00H 03H 06H A8H
Table 4-7 Read Status of DI
Table 4-8 Read F, V1 and V2 Query Message
(603) 746-5524
(603) 746-5524
93
Response
The Acuvim-L series meter response includes the address code, function code,
quantity of data byte, data, and error checking. An example response to read F,
V1 and V2 (F=1388H (50.00Hz), V1=03E7H (99.9V), V2=03E9H (100.1V) is shown
as Table 4-9.
Table 4-9 Read F, V1 and V2 Message of response
4. Preset / Reset Multi-Register (Function Code 16)
Query
Function 16 allows the user to modify the contents of a multi-register. Any
register that exists within the Acuvim-L series meter can have its contents
changed by this message. The example below is a request to an Acuvim-L series
meter with the address of 17 to Preset Ep_imp = (17807783.3KWH), while its HEX
value is 0A9D4089H. Ep_imp data address is 0156H and 0157H.
Addr Fun
Byte
count
Data1
HI
Data1
LO
Data 2
HI
Data2
LO
Data3
HI
Data3
LO
CRC16
HI
CRC16
LO
11H 03H 06H 13H 88H 03H E7H 03H E9H 7FH 04H
Addr Fun
Data start reg
HI
Data start reg
LO
Data #of reg
HI
Data #of reg
LO
Byte Count
11H 10H 01H 56H 00H 02H 04H
Value HI Value LO Value HI Value lO CRC HI CRC LO
0AH 9DH 40H 89H 4DH B9H
Table 4-10 Preset KWH Query Message
(603) 746-5524
(603) 746-5524
94
Response
The normal response to a preset multi-register request includes the Acuvim-L
series meter address, function code, data start register, the number of registers,
and error checking.
Addr Fun
Data start
reg HI
Data start
reg LO
Data #of
reg HI
Data #of
reg LO
CRC16
HI
CRC16
LO
11H 10H 01H 0CH 00H 02H A2H B4H
4.4 Data Address Table
Basic measurements
The data address of basis measurements includes primary data address and
secondary data address. Function code: 03 read.
Table 4-11 Preset KWH Query Message
(603) 746-5524
(603) 746-5524
95
Address Parameter Range Data type
Type of
access
130H Frequency F 4500~6500 word R
131H Phase voltage V1 0~65535 word R
134H Line voltage V12 0~65535 word R
137H Phase(line)current I1 0~65535 word R
13AH Neutral line current In 0~65535 word R
13BH Phase power Pa -32768~32767 Integer R
13CH Phase power Pb -32768~32767 Integer R
13DH Phase power Pc -32768~32767 Integer R
13EH System power Psum -32768~32767 Integer R
13FH Phase reactive power Qa -32768~32767 Integer R
140H Phase reactive power Qa -32768~32767 Integer R
141H Phase reactive power Qb -32768~32767 Integer R
142H System reactive power -32768~32767 Integer R
143H System apparent power 0~65535 word R
144H Phase power factor PFa -1000~1000 Integer R
145H Phase power factor PFb -1000~1000 Integer R
146H Phase power factor PFc -1000~1000 Integer R
147H System power factor -1000~1000 Integer R
148H Voltage unbalance factor 0~1000 word R
149H Current unbalance factor 0~1000 word R
14AH Load nature RT (L/C/R) 76/67/82 word R
14BH Phase apparent power Sa -32768~32767 Integer R
14CH Phase apparent power Sb -32768~32767 Integer R
(603) 746-5524
(603) 746-5524
96
14DH Phase apparent power Sc -32768~32767 Integer R
14EH reserved --- --- ---
14FH Apparent power demand -32768~32767 Integer R
150H Power demand P_Dmd -32768~32767 Integer R
151H Reactive power demand -32768~32767 Integer R
152H Phase A current demand 0~65535 word R
153H Phase B current demand 0~65535 word R
154H Phase C current demand 0~65535 word R
155H reserved 0 --- R
Table4-12 secondary data address of basic measurement
The relationship between numerical value in register of the Acuvim-L series meter and the real physical
value is shown in the following table. (Rx is numerical value in register of the Acuvim-L series meter)
Parameter Relationship Unit
Voltage V1,V2,V3,V12,V23,V31 U=Rx (PT1 / PT2) /10 Volt(V)
Current I1,I2,I3, In I=Rx (CT1/CT2) /1000 Amp(A)
Power Pa, Pb, Pc, Psum P=Rx (PT1 / PT2) (CT1/ CT2) Watt(W)
Reactive power Qa, Qb, Qc, Qsum Q=Rx (PT1 / PT2) (CT1/ CT2) var
Apparent power Sa,Sb,Sc,Ssum S=Rx (PT1 / PT2) (CT1/ CT2) VA
Power factor PFa, PFb, PFc, PFsum PF=Rx / 1000 NA
Frequency F=Rx / 100 Hz
Load nature (R/L/C) 76/67/82 NA
Voltage or current unbalance
factor U_unbl, I_unbl
Unbl=(Rx/1000)100% NA
Table 4-13 Conversion relationship of basic measurements
(603) 746-5524
(603) 746-5524
97
Address Parameter Data type
Type of
access
0600H~0601H Frequency F Float R
0602H~0603H Phase voltage V1 Float R
0608H~0609H Line voltage V12 Float R
060AH~060BH Line voltage V23 Float R
060CH~060DH Line voltage V31 Float R
060EH~060FH Phase (line) current I1 Float R
0610H~0611H Phase (line) current I2 Float R
0612H~0613H Phase (line) current I3 Float R
0614H~0615H Neutral line current In Float R
0616H~0617H Phase power Pa Float R
0618H~0619H Phase power Pb Float R
061AH~061BH Phase power Pc Float R
061CH~061DH System power Psum Float R
061EH~061FH Phase reactive power Qa Float R
0620H~0621H Phase reactive power Qb Float R
0622H~0623H Phase reactive power Qc Float R
0624H~0625H System reactive power Float R
0626H~0627H System apparent Ssum Float R
0628H~0629H Phase power factor PFa Float R
062AH~062BH Phase power factor PFb Float R
062CH~062DH Phase power factor PFc Float R
062EH~062FH System power PFsum Float R
0630H~0631H Voltage unbalance factor Float R
0632H~0633H Current unbalance factor Float R
0634H~0635H Reserved Float R
(603) 746-5524
(603) 746-5524
98
0636H~0637H Phase apparent power Sa Float R
0638H~0639H Phase apparent power Sb Float R
063AH~063BH Phase apparent power Sc Float R
063CH~063DH Reserved Float R
063EH~063FH Apparent power demand Float R
0640H~0641H Power demand P_Dmd Float R
0642H~0643H Reactive power demand Float R
0644H~0645H Phase A current demand Float R
0646H~0647H Phase A current demand Float R
0648H~0649H Phase C current demand Float R
064AH~064BH Reserved Float R
Power quality measurements (Function code: 03 read )
If the instrument model Acuvim-AL/BL/CL, the energy parameter address list please
refer to Table 4-15; if the instrument model Acuvim-DL, the energy parameter address
list please refer to Table 4-16.
Table 4-14 Primary data address of basic measurements
(603) 746-5524
(603) 746-5524
99
Address Parameter
Data
Range
Data
type
Type of
access
400H
Total harmonic distortion of V1
or V12 THD_V1
0~10000 word R
401H
or V23 THD_V2
0~10000 word R
402H
or V31 THD_V3
0~10000 word R
403H Total harmonic distortion of I1 THD_ I1 0~10000 word R
406H~413H Harmonic content of V1 or V12 (2
nd
~15
th
) 0~10000 word R
414H~421H Harmonic content of V2 or V23 (2
nd
~15
th
) 0~10000 word R
422H~42FH Harmonic content of V3 or V31 (2
nd
~15
th
) 0~10000 word R
430H~43DH Harmonic content of I1 (2
nd
~15
th
) 0~10000 word R
43EH~44BH Harmonic content of I2 (2
nd
~15
th
) 0~10000 word R
44CH~459H Harmonic content of I3 (2
nd
~15
th
) 0~10000 word R
Table 4-15 Data table of Power quality measurements
(603) 746-5524
(603) 746-5524
100
The relationship between numerical value in register of Acuvim-L and the real
physical value is as following table. (Rx is numerical value in register of Acuvim-L)
Statistics measurements
Function code: 03 read
Address Parameter Range
Data
type
Type of
access
400H Total harmonic distortion of V1 or V12 0~10000 word R
406H~41DH Harmonic content of V1 or V12(2
nd
~25
th
) 0~10000 word R
41EH~435H Harmonic content of V2 or V23 (2
nd
~25
th
) 0~10000 word R
436H~44DH Harmonic content of V3 or V31 (2
nd
~25
th
) 0~10000 word R
44EH~465H Harmonic content of I1 (2
nd
~25
th
) 0~10000 word R
466H~47DH Harmonic content of I2 (2
nd
~25
th
) 0~10000 word R
47EH~495H Harmonic content of I3 (2
nd
~25
th
) 0~10000 word R
Table 4-16 Data table of Power quality measurements
THD THD=Rx/10000100% NA
Harmonic content THDn=Rx/10000100% NA
Table 4-17 Conversion relationship of Power quality measurements
(603) 746-5524
(603) 746-5524
101
1000H~1003H
Max of V1 V1_max(format: value/
yy mm/dd hh/mm ss)
0~65535 word R
1004H~1007H Max of V2 V2_max and time 0~65535 word R
1008H~100BH Max of V3 V3_max and time 0~65535 word R
100CH~100FH Max of V12 V12_max and time 0~65535 word R
1018H~101BH Max of I1 I1_max and time 0~65535 word R
101CH~101FH Max of I2 I2_max and time 0~65535 word R
1020H~1023H Max of I3 I3_max and time 0~65535 word R
1024H~1027H
Max of power demand PDmd_max
and
-32768~32767 integer R
1028H~102BH
Max of reactive power demand
QDmd_max
-32768~32767 integer R
102CH~102FH
Max of current demand Ia IaDmd_
max
0~65535 word R
1030H~1033H
Max of current demand Ib IbDmd_
max
0~65535 word R
1034H~1037H
Max of current demand Ic IcDmd_
max
0~65535 word R
1038H~103BH
Max of apparent power demand
SDmd_max
0~65535 word R
103CH~103FH Min of V1 V1_min and time 0~65535 word R
1040H~1043H Min of V2 V2_min and time 0~65535 word R
1048H~104BH Min of V12 V12_min and time 0~65535 word R
104CH~104FH Min of V23 V23_min and time 0~65535 word R
1054H~1057H Min of I1 I1_min and time 0~65535 word R
1058H~105BH Min of I2 I2_min and time 0~65535 word R
105CH~105FH Min of I3 I3_min and time 0~65535 word R
Table 4-18 data address of Statistics measurements
(603) 746-5524
(603) 746-5524
102
The data format of statistics measurements is the same as that of Basis
measurements.
This address space is stored meter run time and load run-time parameters, as
shown in the table.
180H Meter run time (high 16 bit)
0~999999999 Dword R
181H Meter run time (low 16 bit)
182H Load run time (high 16 bit)
0~999999999 Dword R
183H Load run time (low 16 bit)
The table below is the conversion relationship for run time.
Meter run time Run_Hur = Rx/10 H
Load run time Run_LoadHur = Rx/10 H
Table4-19 run time parameter address
Table4-20 Conversion relationship of run time
(603) 746-5524
(603) 746-5524
103
Parameter setting
Function code: 03 read; 16 preset
Address Parameter
Type of
acccess
Data type
Data
type
0100H Access code R/W 0~9999 word
0101H
Communication
address
R/W 0~247 word
0102H Baud rate R/W 1200~38400 word
0103H Voltage wiring type R/W
0:3LN,1:2LN,2:2LL,3:3LL (AL/BL/CL/
DL)
word
0:3LN,1: 3LL,2: 2LL(-EL)
0:3LN;1:3LL;2:2LL;3:1LN (-KL)
0104H
Current wiring
type
R/W
0:3CT (-EL) word
0:3CT, 1:2CT,2:1CT(-AL/BL/CL/DL/
KL)
0105H PT1(high 16 bit) R/W
50.0~1000000.0
word
0106H PT1(low 16 bit) R/W word
0107H PT2 R/W 50.0~400.0 word
0108H CT1 R/W 1~50000 word
0109H CT2 R/W 1 & 5 word
010AH
Defnition of ractive
power
R/W
0: sinusoidal
1: nonsinusoidal
word
010BH Backlignt time R/W 0~120(min) word
010CH
Time of demand
slide window
R/W 1~30 word
010DH Clear max R/W 0AH:clear word
010EH
Clear energy
enable
R/W 0:disable;1:enable word
010FH Clear energy R/W 0:disable; 0AH:enable word
0110H Clear runhour R/W 0AH:clear,other:do not clear word
(603) 746-5524
(603) 746-5524
104
0111H Clear load runhour R/W 0AH:clear,other:do not clear word
0112H Parity check choice R/W 0: EVEN; 1: odd; 2: NON2; 3:NON1 word
0113H VAR/PF choice R/W 0:IEC;1:IEEE word
0114H
Sharp tarif
demand clear
R/W 0AH:clear,other:do not clear word
0115H
Peak tarif demand
clear
0116H
Valley tarif
demand clear
0117H
Normal tarif
demand clear
0118H
Total tarif demand
clear
Parameter of clock
Function code:03 read,16:preset
address parameter range Data type Type of access
0184H Year 2000-2099 Word R/W
0185H Month 1-12 Word R/W
0186H Day 1-31 Word R/W
0187H Hour 0-23 Word R/W
0188H Minute 0-59 Word R/W
0189H Second 0-59 Word R/W
018AH Week 0-6 Word R/W
Table4-21 Data address of setting parameter
Table 4-22 Data address of clock parameter
(603) 746-5524
(603) 746-5524
105
Energy measurements
The data address of energy measurements includes real time energy and TOU
energy, the relationship between the real time energy and TOU energy as the
following table:
Data address of real time energy and single-phase energy, function: 03 read; 16
preset.
Data address of
TOU energy
Data address of
energy
Data address of
real time energy
Figure 4-1 division plans of energy address
Data address of
total energy
Data address of
single-phase energy
Data address of
real time energy
Figure 4-2 division plans of real time energy
(603) 746-5524
(603) 746-5524
106
Address Parameter Range
Data
type
Type of
access
0156H~0157H Import energy Ep_imp 0~99999999.9 Dword R/W
0158H~0159H Export energy Ep_exp 0~99999999.9 Dword R/W
015AH~015BH Import reactive energy Eq_imp 0~99999999.9 Dword R/W
015CH~015DH Export reactive energy Eq_exp 0~99999999.9 Dword R/W
015EH~015FH Apparent energy Es 0~99999999.9 Dword R/W
0160H~0161H Phase-A import energy Ep_imp 0~99999999.9 Dword R/W
0162H~0163H Phase-A export energy Ep_exp 0~99999999.9 Dword R/W
0164H~0165H Phase-B import energy Ep_imp 0~99999999.9 Dword R/W
0166H~0167H Phase-B export energy Ep_exp 0~99999999.9 Dword R/W
0168H~0169H Phase-C import energy Ep_imp 0~99999999.9 Dword R/W
016AH~016BH Phase-C export energy Ep_exp 0~99999999.9 Dword R/W
016CH~016DH
Phase-A reactive import energy
Eq_imp
0~99999999.9 Dword R/W
016EH~016FH
Phase-A reactive export energy
Eq_exp
0~99999999.9 Dword R/W
0170H~0171H
Phase-B reactive import energy
Eq_imp
0~99999999.9 Dword R/W
0172H~0173H
Phase-B reactive export energy
Eq_exp
0~99999999.9 Dword R/W
0174H~0175H
Phase-C reactive import energy
Eq_imp
0~99999999.9 Dword R/W
0176H~0177H
Phase-C reactive export energy
Eq_exp
0~99999999.9 Dword R/W
0178H~0179H
Phase-A apparent energy
Es_a
0~99999999.9 Dword R/W
017AH~017BH
Phase-B apparent energy
Es_b
0~99999999.9 Dword R/W
017CH~017DH
Phase-C apparent energy
Es_c
0~99999999.9 Dword R/W
Table4-23 data address of real time energy
(603) 746-5524
(603) 746-5524
107
parameter relationship unit
Power energy Ep_imp,Ep_exp Ep = Rx/10 Kwh
Reactive energy Eq_imp,Eq_exp Ep = Rx/10 Kvarh
Apparent energy Es Ep = Rx/10 Kvah
Table4-24 Conversion of energy parameter
(603) 746-5524
(603) 746-5524
108
Data address of TOU energy
The data address save the parameter of energy, which includes Data address of
last month TOU energy, Data address of current month TOU energy, Data address
of TOU parameter setting and Data address of TOU default parameter. Except for
the data address of TOU default parameter, the data address could be read with
03 code, preset with 16 code.
Data address of
TOU energy
Data address of last
month TOU
Data address of current
month TOU
Data address of TOU
parameter setting
Data adress of TOU
default parameter
Basis parameter of TOU
Time zone setting parameter of TOU
Time table setting parameter of TOU
Special day setting parameter of TOU
Default basis parameter of TOU
Default time zone setting parameter of TOU
Default time table setting parameter of TOU
Default Special day setting parameter of TOU
Figure4-3 division plan of TOU energy
(603) 746-5524
(603) 746-5524
109
Current month TOU energy
address parameter range Data type
Type of
access
200H~201H
Ep_imp(sharp)
Ep_exp(sharp)
Eq_im(sharp)
Eq_exp(sharp)
Es(sharp)
0~99999999.9 Dword R/W
202H~203H 0~99999999.9 Dword R/W
204H~205H 0~99999999.9 Dword R/W
206H~207H 0~99999999.9 Dword R/W
208H~209H 0~99999999.9 Dword R/W
20AH~20BH Ep_imp(peak)
Ep_exp(peak)
Eq_imp(peak)
Eq_exp(peak)
Es(peak)
0~99999999.9 Dword R/W
20CH~20DH 0~99999999.9 Dword R/W
20EH~20FH 0~99999999.9 Dword R/W
210H~211H 0~99999999.9 Dword R/W
212H~213H 0~99999999.9 Dword R/W
214H~215H
Ep_imp(valley)
Ep_exp(valley)
Eq_imp(valley)
Eq_exp(valley)
Es(valley)
0~99999999.9 Dword R/W
216H~217H 0~99999999.9 Dword R/W
218H~219H 0~99999999.9 Dword R/W
21AH~21BH 0~99999999.9 Dword R/W
21CH~21DH 0~99999999.9 Dword R/W
21EH~21FH Ep_imp(normal)
Ep_exp(normal)
Eq_imp(normal)
Eq_exp(normal)
Es(normal)
0~99999999.9 Dword R/W
220H~221H 0~99999999.9 Dword R/W
222H~223H 0~99999999.9 Dword R/W
224H~225H 0~99999999.9 Dword R/W
226H~227H 0~99999999.9 Dword R/W
228H~229H
Ep_imp(sum)
Ep_exp(sum)
Eq_imp(sum)
Eq_exp(sum)
Es(sum)
0~99999999.9 Dword R/W
22AH~22BH 0~99999999.9 Dword R/W
22CH~22DH 0~99999999.9 Dword R/W
22EH~22FH 0~99999999.9 Dword R/W
230H~231H 0~99999999.9 Dword R/W
(603) 746-5524
(603) 746-5524
110
Last month TOU energy
232H~233H
Ep_imp(sharp)
Ep_exp(sharp)
Eq_imp(sharp)
Eq_exp(sharp)
Es(sharp)
0~99999999.9 Dword R/W
234H~235H 0~99999999.9 Dword R/W
236H~237H 0~99999999.9 Dword R/W
238H~239H 0~99999999.9 Dword R/W
23AH~23BH 0~99999999.9 Dword R/W
23CH~23DH Ep_imp(peak)
Ep_exp(peak)
Eq_imp(peak)
Eq_exp(peak)
Es(peak)
0~99999999.9 Dword R/W
23EH~23FH 0~99999999.9 Dword R/W
240H~241H 0~99999999.9 Dword R/W
242H~243H 0~99999999.9 Dword R/W
244H~245H 0~99999999.9 Dword R/W
246H~247H Ep_imp(valley)
Ep_exp(valley)
Eq_imp(valley)
Eq_exp(valley)
Es(valley)
0~99999999.9 Dword R/W
248H~249H 0~99999999.9 Dword R/W
24AH~24BH 0~99999999.9 Dword R/W
24CH~24DH 0~99999999.9 Dword R/W
24EH~24FH 0~99999999.9 Dword R/W
250H~251H
Ep_imp(normal)
Ep_exp(normal)
Eq_imp(normal)
Eq_exp(normal)
Es(normal)
0~99999999.9 Dword R/W
252H~253H 0~99999999.9 Dword R/W
254H~255H 0~99999999.9 Dword R/W
256H~257H 0~99999999.9 Dword R/W
258H~259H 0~99999999.9 Dword R/W
25AH~25BH
Ep_imp(sum)
Ep_exp(sum)
Eq_imp(sum)
Eq_exp(sum)
Es(sum)
0~99999999.9 Dword R/W
25CH~25DH 0~99999999.9 Dword R/W
25EH~25FH 0~99999999.9 Dword R/W
260H~261H 0~99999999.9 Dword R/W
262H~263H 0~99999999.9 Dword R/W
Table4-25 data address of last and current month
(603) 746-5524
(603) 746-5524
111
Data address of TOU parameter setting includes basis parameter of TOU,
time zone setting parameter of TOU, time table setting parameter of TOU
and holiday setting parameter of TOU. Function: 03 code, 16: preset.
Basis parameter of TOU
0800H number of time zone 0~12 Word R/W
0801H number of time table 0~14 Word R/W
0802H number of time interval 0~14 Word R/W
0803H fee 0~3 Word R/W
0804H Weekly rest 0~127 Word R/W
0805H time table of Weekly rest 0-14 Word R/W
0806H number of special day 0-30 Word R/W
0807H Function enable of TOU 1:enable Word R/W
0808H Initialization of TOU 1:enable Word R/W
0809H
Choice of calculation
(0: end of month ; 1: setting
day)
Word R/W
080AH
The time of caculation:
day(default is 1)
1~31 Word R/W
080BH
hour(default is 0)
0~23 Word R/W
080CH
minute(default is 0)
0~59 Word R/W
(603) 746-5524
(603) 746-5524
112
080DH
second(default is 0)
0~59 Word R/W
080EH
TOU energy parameter
Setting error status word
0: the setting of parameter is
correct;
1: the fee in parameter setting is
error;
2: the time interval num is error;
4: the time table num is error;
8: the time zone num is error;
16: the parameter setting in time
zone is error;
32: the special day num is error;
64: the parameter setting in special
day is error;
256: the fee in time table is error;
512: the time setting in time table
is error;
1024: the time interval in time
table is error;
2048: the time interval of week rest
is error;
4096: the setting parameter of
weekend is error;
Time zone setting parameter of TOU
0820H~0822H
data and the time table
Of the 1st time zone
word R/W
0823H~0825H
data and the time tableOf
the 2th time zone
word R/W
0826H~0828H
the 3th time zone
word R/W
0829H~082BH
the 4th time zone
word R/W
082CH~082EH
the 5th time zone
word R/W
(603) 746-5524
(603) 746-5524
113
082FH~0831H
the 6th time zone
word R/W
0832H~0834H
the 7th time zone
word R/W
0835H~0837H
the 8th time zone
word R/W
0838H~083AH
the 9th time zone
word R/W
083BH~083DH
the 10th time zone
word R/W
083EH~0840H
the 11th time zone
word R/W
0841H~0843H
the 12th time zone
word R/W
Time table parameter of TOU
0844H~0846H
1st time interval and fee of
the 1st time table
word R/W
0847H~0849H
2th time interval and fee of
the 1st time table
word R/W
084AH~084CH
the 1st time table
word R/W
084DH~084FH
the 1st time table
word R/W
0850H~0852H
the 1st time table
word R/W
0853H~0855H
the 1st time table
word R/W
0856H~0858H
the 1st time table
word R/W
0859H~085BH
the 1st time table
word R/W
085CH~085EH
the 1st time table
word R/W
(603) 746-5524
(603) 746-5524
114
085FH~0861H
the 1st time table
word R/W
0862H~0864H
the 1st time table
word R/W
0865H~0867H
the 1st time table
word R/W
0868H~086AH
the 1st time table
word R/W
086BH~086DH
the 1st time table
word R/W
086EH~0897H
From 1st to 14th time
interval and fee of the 2th
time table
The same
as 1st time
table
word R/W
0898H~08C1H
time table
The same
as 1st time
table
word R/W
08C2H~08EBH
time table
The same
as 1st time
table
word R/W
08ECH~0915H
time table
The same
as 1st time
table
word R/W
0916H~093FH
time table
The same
as 1st time
table
word R/W
0940H~0969H
time table
The same
as 1st time
table
word R/W
096AH~0993H
time table
The same
as 1st time
table
word R/W
(603) 746-5524
(603) 746-5524
115
0994H~09BDH
time table
The same
as 1st time
table
word R/W
09BEH~09E7H
time table
The same
as 1st time
table
word R/W
09E8H~0A11H
time table
The same
as 1st time
table
word R/W
0A12H~0A3BH
time table
The same
as 1st time
table
word R/W
0A3CH~0A65H
time table
The same
as 1st time
table
word R/W
0A66H~0A8FH
time table
The same
as 1st time
table
word R/W
Special day parameter of TOU
0A90H~0A92H
the 1st holiday
word R/W
0A93H~0A95H
the 2th holiday
word R/W
0A96H~0A98H
data and the time table Of
the 3th holiday
word R/W
0A99H~0A9BH
the 4th holiday
word R/W
0A9CH~0A9EH
the 5th holiday
word R/W
0A9FH~0AA1H
the 6th holiday
word R/W
0AA2H~0AA4H
the 7th holiday
word R/W
(603) 746-5524
(603) 746-5524
116
0AA5H~0AA7H
the 8th holiday
word R/W
0AA8H~0AAAH
the 9th holiday
word R/W
0AABH~0AADH
the 10th holiday
word R/W
0AAEH~0AB0H
the 11th holiday
word R/W
0AB1H~0AB3H
the 12th holiday
word R/W
0AB4H~0AB6H
the 13th holiday
word R/W
0AB7H~0AB9H
the 14th holiday
word R/W
0ABAH~0ABCH
the 15th holiday
word R/W
0ABDH~0ABFH
the 16th holiday
word R/W
0AC0H~0AC2H
the 17th holiday
word R/W
0AC3H~0AC5H
the 18th holiday
word R/W
0AC6H~0AC8H
the 19th holiday
word R/W
0AC9H~0ACBH
the 20th holiday
word R/W
0ACCH~0ACEH
the 21th holiday
word R/W
0ACFH~0AD1H
the 22th holiday
word R/W
0AD2H~0AD4H
the 23th holiday
word R/W
(603) 746-5524
(603) 746-5524
117
0AD5H~0AD7H
the 24th holiday
word R/W
0AD8H~0ADAH
the 25th holiday
word R/W
0ADBH~0ADDH
the 26th holiday
word R/W
0ADEH~0AE0H
the 27th holiday
word R/W
0AE1H~0AE3H
the 28th holiday
word R/W
0AE4H~0AE6H
the 29th holiday
word R/W
0AE7H~0AE9H
the 30th holiday
word R/W
0AEAH Holiday setting enable word R/W
0AEBH Start year holiday setting word R/W
0AECH End year holiday setting word R/W
Table4-26 data address of TOU
The address area include ten years holiday setting, Function: 03H Read 10H Preset
The 1st year Holiday address Function: 03H Read 10H Preset
B00H~B02H
The 1st holiday and time table
(format: month /day /time table)
word R/W
B03H~B05H The 2nd holiday and time table word R/W
B06H~B08H The 3rd holiday and time table word R/W
B09H~B0BH The 4th holiday and time table word R/W
B0CH~B0EH The 5th holiday and time table word R/W
B0FH~B11H The 6th holiday and time table word R/W
B12H~B14H The 7th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
118
B18H~B1AH The 9th holiday and time table word R/W
B1BH~B1DH The 10th holiday and time table word R/W
B1EH~B20H The 11th holiday and time table word R/W
B2AH~B2CH The 15th holiday and time table word R/W
B2DH~B2FH The 16th holiday and time table word R/W
B5AH The 1st setting year word R/W
B5BH Holiday number of the 1st year word R/W
The 2nd year Holiday address Function: 03H Read 10H Preset
B5CH~B5EH
word R/W
B5FH~B61H The 2nd holiday and time table word R/W
B62H~B64H The 3rd holiday and time table word R/W
(603) 746-5524
(603) 746-5524
119
B7AH~B7CH The 11th holiday and time table word R/W
B7DH~B7FH The 12th holiday and time table word R/W
B9EH~BA0H The 23th holiday and time table word R/W
BA1H~BA3H The 24th holiday and time table word R/W
BAAH~BACH The 27th holiday and time table word R/W
BADH~BAFH The 28th holiday and time table word R/W
BB0H~BB2H The 29th holiday and time table word R/W
BB3H~BB5H The 30th holiday and time table word R/W
BB6H The 2nd setting year word R/W
BB7H Holiday number of the 2nd year word R/W
(603) 746-5524
(603) 746-5524
120
The 3rd year Holiday address Function: 03H Read 10H Preset
BB8H~BBAH
word R/W
BBBH~BBDH The 2nd holiday and time table word R/W
BBEH~BC0H The 3rd holiday and time table word R/W
BC1H~BC3H The 4th holiday and time table word R/W
BCAH~BCCH The 7th holiday and time table word R/W
BCDH~BCFH The 8th holiday and time table word R/W
BD0H~BD2H The 9th holiday and time table word R/W
BD9H~BDBH The 12th holiday and time table word R/W
BDCH~BDEH The 13th holiday and time table word R/W
BDFH~BE1H The 14th holiday and time table word R/W
BE2H~BE4H The 15th holiday and time table word R/W
BE5H~BE7H The 16th holiday and time table word R/W
BE8H~BEAH The 17th holiday and time table word R/W
BEBH~BEDH The 18th holiday and time table word R/W
BEEH~BF0H The 19th holiday and time table word R/W
BF1H~BF3H The 20th holiday and time table word R/W
BFAH~BFCH The 23th holiday and time table word R/W
BFDH~BFFH The 24th holiday and time table word R/W
C00H~C02H The 25th holiday and time table word R/W
C09H~C0BH The 28th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
121
C0CH~C0EH The 29th holiday and time table word R/W
C0FH~C11H The 30th holiday and time table word R/W
C12H The 3rd setting year word R/W
C13H Holiday number of the 3rd year word R/W
The 4th year Holiday address Function: 03H Read 10H Preset
C14H~C16H
word R/W
C17H~C19H The 2nd holiday and time table word R/W
C1AH~C1CH The 3rd holiday and time table word R/W
C1DH~C1FH The 4th holiday and time table word R/W
C38H~C3AH The 13th holiday and time table word R/W
C3BH~C3DH The 14th holiday and time table word R/W
C3EH~C40H The 15th holiday and time table word R/W
C4AH~C4CH The 19th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
122
C6EH The 4th setting year word R/W
C6FH Holiday number of the 4th year word R/W
C70H~C72H
word R/W
C73H~C75H The 2nd holiday and time table word R/W
C76H~C78H The 3rd holiday and time table word R/W
C8EH~C90H The 11th holiday and time table word R/W
C9AH~C9CH The 15th holiday and time table word R/W
CA0H~CA2H The 17th holiday and time table word R/W
CA9H~CABH The 20th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
123
CACH~CAEH The 21th holiday and time table word R/W
CAFH~CB1H The 22th holiday and time table word R/W
CB2H~CB4H The 23th holiday and time table word R/W
CB5H~CB7H The 24th holiday and time table word R/W
CB8H~CBAH The 25th holiday and time table word R/W
CBBH~CBDH The 26th holiday and time table word R/W
CBEH~CC0H The 27th holiday and time table word R/W
CC1H~CC3H The 28th holiday and time table word R/W
CCAH The 5th setting year word R/W
CCBH Holiday number of the 5th year word R/W
CCCH~CCEH
word R/W
CCFH~CD1H The 2nd holiday and time table word R/W
CD2H~CD4H The 3rd holiday and time table word R/W
CD5H~CD7H The 4th holiday and time table word R/W
CD8H~CDAH The 5th holiday and time table word R/W
CDBH~CDDH The 6th holiday and time table word R/W
CDEH~CE0H The 7th holiday and time table word R/W
CE1H~CE3H The 8th holiday and time table word R/W
CD4H~CE6H The 9th holiday and time table word R/W
CE7H~CE9H The 10th holiday and timetable word R/W
CEAH~CECH The 11th holiday and time table word R/W
CEDH~CEFH The 12th holiday and time table word R/W
CF0H~CF2H The 13th holiday and time table word R/W
CF9H~CFBH The 16th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
124
CFCH~CFEH The 17th holiday and time table word R/W
CFFH~D01H The 18th holiday and time table word R/W
D02H~D04H The 19th holiday and time table word R/W
D08H~D0AH The 21th holiday and time table word R/W
D0BH~DODH The 22th holiday and time table word R/W
D0EH~D10H The 23th holiday and time table word R/W
D1AH~D1CH The 27th holiday and time table word R/W
D1DH~D1FH The 28th holiday and time table word R/W
D26H The 6th setting year word R/W
D27H Holiday number of the 6th year word R/W
D28H~D2AH
word R/W
D2BH~D2DH The 2nd holiday and time table word R/W
D2EH~D30H The 3rd holiday and time table word R/W
D49H~D4BH The 12th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
125
D4CH~D4EH The 13th holiday and time table word R/W
D4FH~D51H The 14th holiday and time table word R/W
D58H~D5AH The 17th holiday and time table word R/W
D5BH~D5DH The 18th holiday and time table word R/W
D5EH~D60H The 19th holiday and time table word R/W
D7FH~D81H The 30th holiday and time table word R/W
D82H The 7th setting year word R/W
D83H Holiday number of the 7th year word R/W
D84H~D86H
word R/W
D87H~D89H The 2nd holiday and time table word R/W
D8AH~D8CH The 3rd holiday and time table word R/W
(603) 746-5524
(603) 746-5524
126
D9FH~DA1H The 10th holiday and time table word R/W
DA2H~DA4H The 11th holiday and time table word R/W
DA5H~DA7H The 12th holiday and time table word R/W
DA8H~DAAH The 13th holiday and time table word R/W
DABH~DADH The 14th holiday and time table word R/W
DAEH~DB0H The 15th holiday and time table word R/W
DB1H~DB3H The 16th holiday and time table word R/W
DBAH~DBCH The 19th holiday and time table word R/W
DBDH~DBFH The 20th holiday and time table word R/W
DC0H~DC2H The 21th holiday and time table word R/W
DC9H~DCBH The 24th holiday and time table word R/W
DCCH~DCEH The 25th holiday and time table word R/W
DCFH~DD1H The 26th holiday and time table word R/W
DD2H~DD4H The 27th holiday and time table word R/W
DD5H~DD7H The 28th holiday and time table word R/W
DD8H~DDAH The 29th holiday and time table word R/W
DDBH~DDDH The 30th holiday and time table word R/W
DDEH The 8th setting year word R/W
DDFH Holiday number of the 8th year word R/W
DE0H~DE2H
word R/W
DE3H~DE5H The 2nd holiday and time table word R/W
DE6H~DE8H The 3rd holiday and time table word R/W
DE9H~DEBH The 4th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
127
DECH~DEEH The 5th holiday and time table word R/W
DEFH~DF1H The 6th holiday and time table word R/W
DF2H~DF4H The 7th holiday and time table word R/W
DF5H~DF7H The 8th holiday and time table word R/W
DF8H~DFAH The 9th holiday and time table word R/W
DFBH~DFDH The 10th holiday and time table word R/W
DFEH~E00H The 11th holiday and time table word R/W
E01H~E03H The 12th holiday and time table word R/W
E0AH~E0CH The 15th holiday and time table word R/W
E0DH~E0FH The 16th holiday and time table word R/W
E19H~E1BH The 20th holiday and time table word R/W
E1CH~E1EH The 21th holiday and time table word R/W
E1FH~E21H The 22th holiday and time table word R/W
E28H~E2AH The 25th holiday and time table word R/W
E2BH~E2DH The 26th holiday and time table word R/W
E2EH~E30H The 27th holiday and time table word R/W
E3AH The 9th setting year word R/W
E3BH Holiday number of the 9th year word R/W
(603) 746-5524
(603) 746-5524
128
E3CH~E3EH
word R/W
E3FH~E41H The 2nd holiday and time table word R/W
E42H~E44H The 3rd holiday and time table word R/W
E69H~E6BH The 16th holiday and time table word R/W
E6CH~E6EH The 17th holiday and time table word R/W
E6FH~E71H The 18th holiday and time table word R/W
(603) 746-5524
(603) 746-5524
129
E96H The 10th setting year word R/W
E97H Holiday number of the 10th year word R/W
Table4-27 Data address of ten years holiday
Extend IO Setting Area
It includes extend IO communication parameter , DO related parameter and
DI related parameter. in the extended IO communication section includes
ways to set the baud rate and parity; DO parameters section includes: pulse
output and alarm output function options, when set to pulse output functions,
including pulse constant, pulse width and high level of output delay settings;
When set to alarm output functions, including alarm delay, alarm conditions
and alarm limits set ting. The DI setting contains the DI function selection
and pulse constant setting, the bit0-bit3 correspond to the DI1 to DI4 state in
the 0x3D0 address. If the value of bit0 is 1, it indicates the DI1 status is pulse
counting state. If the value of bit0 is 0, it indicates the DI1 status is SOE state.
Other bits function is same as bit0.
DO Parameter Setting : 03H Read ;10H Write
Address Parameter Range Type
Type of
access
3C0H Do1 function choice
0:pulse output
1:alarm output
word R/W
3C1H Do2 function choice
0:pulse output
1:alarm output
word R/W
3C2H Pulse constant 1~6000 word R/W
3C3H High level dealy 1~50(20ms) word R/W
(603) 746-5524
(603) 746-5524
130
3C4H
Do1 output energy
choice
0:none:
1:Import energy Ep_imp
2:Export energy Ep_exp
3:Import reactive energy Eq_imp
4:Export reactive energy
Eq_exp
word R/W
3C5H
Do2 output energy
choice
0:none;
1:Import energy Ep_imp
2:Export energy Ep_exp
3:Import reactive energy Eq_imp
4:Export reactive energy
Eq_exp
word R/W
3C6H Alarm delay 0~255(300ms) word R/W
3C7H Do1 alarm choice 0~34 word R/W
3C8H Do1 alarm condition 0 <; 1> ; word R/W
3C9H Do1 alarm limit 0~65535 word R/W
3CAH Do2 alarm choice 0~34 word R/W
3CBH Do2 alarm condition 0 <; 1> ; word R/W
3CCH Do2 alarm limit 0~65535 word R/W
3CDH
Extend
communication
Baud rate
1200-38400 word R/W
3CEH
Extend
communication
Parity check
0: EVEN 1: odd
2:NON2 3:NON1
word R/W
3CFH
Alarm back light
blink setting
0:enable:
1:disable
word R/W
DI parameter setting: 03H Read;10H Write
3D0H
Bit0/ Bit1/ Bit2/ Bit3: 0 SOE state ;
Bit0/ Bit1/ Bit2/ Bit3: 1 pulse counter state;
0 - 15 R/W
3D1H High Byte of pulse accumulation constant 1-65535 R/W
(603) 746-5524
(603) 746-5524
131
3D2H DI counter clear
0x0A: clear
Other: NONE
R/W
Table 4-28 Extend IO Parameter setting
The address area contains pulse counter number. The pulse counter number
could be reserved with power-down, it also could be clear through PC
software.
DI counter parameter:03H Read;10H Write
0x3A0H~0x3A1H DI1 counter number 0-4294967295 Dword
Table 4-29 data address of pulse accumulation
It contains 20 SOE events during 0x300 and 0x363 address area, it indicates 1st
SOE event address area from 0x300H to 0x304, the format as: year-month, day-
hour, minute-second, millisecond and DI state. The others format is same as
frst event.
SOE event record area: 03H Read
0x300H
Year of 1st SOE Event(High Byte) 00-99
word
Month of 1st SOE Event(Low Byte) 1-12
0x301H
Day of 1st SOE Event(High Byte) 1-31
word
Hour of 1st SOE Event(Low Byte) 0-23
0x302H
Minute of 1st SOE Event(High Byte) 0-59
word
second of 1st SOE Event(Low Byte) 0-59
0x303H Millisecond of 1st SOE Event 0-999 word
(603) 746-5524
(603) 746-5524
132
0x304H 1st SOE event state 0-15 word
0x305H~0x309H 2nd SOE event same word
0x30aH~0x30eH 3th SOE event same word
0x30fH~0x313H 4th SOE event same word
0x314H~0x318H 5th SOE event same word
0x319H~0x31dH 6th SOE event same word
0x31eH~0x322H 7th SOE event same word
0x328H~0x32cH 9th SOE event same word
0x32dH~0x331H 10th SOE event same word
0x337H~0x33bH 12th SOE event same word
0x33cH~0x340H 13th SOE event same word
0x346H~0x34aH 15th SOE event same word
0x34bH~0x34fH 16th SOE event same word
0x35aH~0x35eH 19th SOE event same word
0x35fH~0x363H 20th SOE event same word
Table 4-30 SOE event parameter address area
The address area for the SOE single event reading, through continuous
reading of the address area of a single SOE record, achieving the current
single SOE records continuously updated to meet the SOE event to read all
20 goals. One address 0x406H, the type of access is read and write, it can
achieve the specifed single event reading by writing the location of a single
SOE records to the address.
(603) 746-5524
(603) 746-5524
133
SOE single event record area: 03H Read; 10H Write
0x380H
Year of 1st SOE Event(High Byte) 00-99
word R
Month of 1st SOE Event(Low Byte) 1-12
0x381H
Day of 1st SOE Event(High Byte) 1-31
word R
Hour of 1st SOE Event(Low Byte) 0-23
0x382H
Minute of 1st SOE Event(High Byte) 0-59
word R
second of 1st SOE Event(Low Byte) 0-59
0x383H Millisecond of 1st SOE Event 0-999 word R
0x384H SOE event state 0-15 word R
0x385H
The latest record group number of
single SOE event
0:none
word R
1-20: the The
latest record
group number
0x386H
Current group number of single SOE
event
Other:none
word R/W
1-20: Current
group number
Digital Output State
the user can monitor DO state by reading the address area. The function code is
01H.
DO State Reading Area: 01 Function
0000H DO1 1:ON 0:OFF bit
0001H DO2 1:ON 0:OFF bit
Table 4-32 DO State Reading Area
Table 4-31 Single SOE event parameter address area
(603) 746-5524
(603) 746-5524
134
Digital Input State

The user can monitor DI state by reading the address area. The function code is
02H.
DI State Reading Area: 02 Function
0000H DI1 1:ON 0:OFF bit
Table 4-33 DI State Reading Area
Note:
1. data type:
Word: unsigned integer of 16 bit;
Integer: signed integer of 16 bit;
DWord: unsigned integer of 32 bit;
Float: foat data of 32 bit.
2. type of access
R: read only, data read by using function code 03.
R/W: read and write, data read by using function 03 and written by using
function code 16.
It is forbidden to write data address which dose not possesses property to
be written.
3. Energy and run time
Energy and run time data is represented in 32 bit. Both high 16 bit and low
16 bit have successive address alone. The high 16 bit should be multiplied
(603) 746-5524
(603) 746-5524
135
by 65535 and plus low 16 bit data to get the energy and run time data in
master software. The unit is 0.1kWh, 0.1kVarh and 0.1hour. The energy
register can be cleared or preset via communication. The register of run time
can be cleared and can not be preset.
(603) 746-5524
(603) 746-5524
136
(603) 746-5524
(603) 746-5524
Appendix
Appendix A Technical Data and Specifcations
Appendix B Ordering Information
Appendix C Revision History
(603) 746-5524
(603) 746-5524
138
Appendix A Technical data and Specifcation
Input ratings

Voltage input
Voltage rating 400 LN / 690 LL Vac RMS (3-phase)
400 LN Vac RMS (single-phase)
With 20% overage (3LN or 2LN wiring)
Installation Category III, Pollution Degree 2
Frequency range 45~65Hz
Overload 2 times(continuously);
2500Vac per second (no recurrence)
Voltage range through PT 1000KV highest at primary side
PT burden <0.2VA
Measuring True-RMS
Current input
Current rating 5Amp AC (1Amp AC Optional)
Current range 50000A highest at primary side
Overload 10A (continuously); 100A per sec(no recurrence)
CT burden <0.5VA
Measuring True-RMS
(603) 746-5524
(603) 746-5524
139
METERING
Parameters
Accuracy
Resolution Range
Acuvim-L
Acuvim-
EL/KL
Voltage 0.5% 0.5% 0.1V 20V~1000kV
Current 0.5% 0.5% 0.001A 0~50000A
Current Demand 0.5% 0.5% 0.001A 0~50000A
Power 0.5% 0.5% 1W 9999~9999MW
Reactive Power 1.0% 0.5% 1var 9999~9999Mvar
Apparent Power 1.0% 0.5% 1VA 0~9999MVA
Power Demand 1.0% 0.5% 1W 9999~9999MW
Reactive Power
Demand
1.0% 0.5% 1var 9999~9999Mvar
Apparent Power
Demand
1.0% 0.5% 1VA 0~9999MVA
Power Factor 1.0% 0.5% 0.001 1.0~1.0
Frequency 0.2% 0.2% 0.01Hz 45.00~65.00Hz
Energy 0.5% 0.5% 0.1kWh 0~99999999.9kWh
Reactive Energy 1.0% 0.5% 0.1kvarh 0~99999999.9kvarh
Apparent Energy 1.0% 0.5% 0.1VAh 0~99999999.9kVAh
Harmonics 2.0% 0.01% 0~100.0%
Running 0.1hrs 0~99999999.9hrs
Running Time (Acuvim-DL/EL/KL) 0.1hrs 0~99999999.9hrs
Accuracy
(603) 746-5524
(603) 746-5524
140
Standards
Measuring IEC 62053-22; ANSI C12.20
Environmental IEC 60068-2
Safety IEC 61010-1, UL 61010-1
EMC IEC 61000-4/2-3-4-5-6-8-11
Dimension DIN 43700/ANSI C39.1
Communication port
RS-485 (Option)
Modbus-RTU Protocol
2-wire connection, Half-duplex, Isolated
1200 to 38400 baud rate
Digital input (DI)
Input Type Dry Contact
Input Resistance 4k
Pulse Frequency (Max) 100Hz, 50% Duty Ratio
SOE Resolution 2ms
Digital output (DO)(Photo-MOS)
Voltage Range 0~250Vac/dc
Load Current 100mA (Max)
Output Frequency (Max) 25Hz, 50% Duty Ratio
Isolation Voltage 2500V
(603) 746-5524
(603) 746-5524
141
Suitable condition
Dimensions (mm) 969651 (cutting-out 9292 or 4inch Round)
Protection level IP56 (front), IP30 (cover)
Weight 350g
Operating temp. range -25C ~ 70C
Storage temp. range -40C ~ 85C
Humidity 5%~95%, non condensation
Power supply 100~415Vac , 50/60Hz; 100~300Vdc
Power consumption 3W
(603) 746-5524
(603) 746-5524
142
Appendix B Ording Information
Acuvim-
A: Acuvim-AL (basic)
B: Acuvim-BL (basic+DO)
C: Acuvim-CL (basic+COMM)
D: Acuvim-DL (basic+COMM+I/O)
E: Acuvim-EL (TOU+COMM+I/O)
K: Acuvim-KL (Acuvim-EL Simple)
5A: 5A
1A: 1A
P1:100~415Vac,50/60Hz
100~300Vdc
P2: 20~60Vdc
L
50: 50Hz
60: 60Hz
X1: 4DI+2DO
X2: 4DI+2DO+RS485
X3: PROFIBUS
X4: 4DI+2DO+PROFIBUS
D: Standard with LCD Display
M: DIN Rail mount(no LCD)
Expansion
Module
Power
Supply
Current
Frequence
DIN Rail
Note: 1. Extent Module only support by Acuvim-DL and Acuvim-EL.
2. The Extend Module X4 consist of IO module and Profbus module.
The Profbus module must be installed on the back of the meter FIRST
before the other module are attached.
(603) 746-5524
(603) 746-5524
143
Remote Display Option
REM-
DS1: Compatible with Acuvim-L Series M (DIN Mount)
models only
(603) 746-5524
(603) 746-5524
144
Appendix C Revision History
Revision Date Description
1.0 20070915 First version
1.1 20070930
Add primary data address table of Basic measurements
data and Statistics measurements data.
1.2 20071109 Add Apparent energy function. See Page 37 and Page 69.
1.3 20090430
Add single phase apparent power, apparent power
demand and the max of apparent power demand; Update
the ordering information.
1.31 20090515 Add TOU function
1.40 20091023
1.41 20100401
Add TOU energy Display, TOU maximum demand and
Holiday auto-switch.
1.42 20101031 Revise the content
1.43 20110430 Updated appendix part of data
1.44 20110530
DI type modifed from wet contact to dry connect;
add contents of PROFIBUS module.
1.45 20110621 Add a "Note" in page 52.
(603) 746-5524
(603) 746-5524
(603) 746-5524
(603) 746-5524

Acuvim L Power Meter User Manual

Uploaded by

Copyright:

Available Formats

Acuvim L Power Meter User Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Acuvim L Power Meter User Manual

Uploaded by

Copyright:

Available Formats

Distributed by MicroDAQ.com, Ltd.

Rear View Rear View of the Remote

You might also like