RFM01

RFM01
Datasheet REV1.2
ISM BAND FSK RECEIVER MODULE

RFM01
the purpose of this spec covers mainly for the physical
characteristic of the module, for register configure and its
related command info please refer to RF01 data sheets
RFM01
General Introduction
RFM01 is a low costing ISM band receiver module
implemented with unique PLL and zero IF design approach.
It works with FSK modulated signal ranges from
315/433/868/915MHZ bands, comply with FCC, ETSI
regulation. The SPI interface is used to communicate with
microcontroller for parameter setting. RFM01 works with
RFM02 transmitter module. At 433MHZ band, the pair of
module can work up to 300m in the free open air.
Features:
Low costing, high performance and price ratio
Tuning free during production
FSK reception
PLL and zero IF technology
Fast PLL lock time
High resolution PLL with 2.5 KHz step
High data rate (up to 115.2 kbps with internal demodulatorwith external RC filter highest data rate is
256 kbps)
Differential antenna input
Automatic antenna tuning
Programmable receiver bandwidth (from 67 to 400 kHz)
Analog and digital signal strength indicator (ARSSI/DRSSI)
AFC
DQD
Internal demodulator
SPI interface
Clock and reset signal output for external MCU use
16 bits FIFO
Low power mode (<0.5mA averaged current consumption)
10MHz crystal for PLL timing
Wakeup timer
Low battery detection
Programmable capacitor bank
2.2V - 5.4V power supply
Low power consumption
Stand by current less than 0.3uA
Tel: +86-755-82973805 Fax: +86-755-82973550
E-mail: sales@hoperf.com http://www.hoperf.com
RFM01
Datasheet REV1.2
Typical Application
Remote control
Remote sensor
Wireless data collection
Home security system
Toys
Tire pressure monitoring system
Pin Definition
SMD
DIP
definition
Type
Function
VDI
DO
Valid data indicator
VDD
Positive power supply
SDI
DI
SPI data input
SCK
DI
SPI clock input
nSEL
DI
Chip select (active low)
FFIT/SDO
DO
FIFO fill interrupt(active low) or status read data output
nRES
DO
Reset outputactive low
GND
Power ground
nIRQ
DO
Interrupts request outputactive low
DATA/nFFS
DO/DI
Data input(non FIFO mode)/ FIFO select

Clock output (no FIFO )/ external filter capacitor(analog mode)/ FIFO
DCLK/CFIL/FFIT
DO/AIO/DO
interrupts(active high)when FIFO level set to 1, FIFO empty

interruption can be achieved
CLK
DO
Clock output for external microcontroller
Tel: +86-755-82973805 Fax: +86-755-82973550
RFM01
Datasheet REV1.2
Electrical Parameter
Maximumnot at working mode
symbol
parameter
minimum
maximum
Unit
Vdd
-0.5
6.0
Vin
All pin input level
-0.5
Vdd+0.5
Iin
Input current except power
-25
25
MA
ESD
Human body model
1000
Tst
Storage temperature
125
Tld
Soldering temperature(10s)
260
-55
Recommended working range

symbol
parameter
minimum
maximum
Unit
Vdd
2.2
5.4
Top
Working temperature
-40
85
DC characteristic
symbol
parameter
Remark
Idd
Current consumption
Ix
Stand by current
minimum
typical
maximum
Unit
315,433MHz band
11
mA
868,915MHz band
10.5
12.5
Crystal
30
35
and
base
mA
band on
Ipd
Sleep mode current
Ilb
Vlb
Low battery step
Vlba
All blocks off
0.1V per step
0.3
uA
0.5
uA
2.2
5.3
75
mV
accuracy
Vil
Low level input
0.3*Vdd
Vih
High level input
Iil
Leakage current
Vil=0V
-1
uA
Iih
Leakage current
Vih=Vdd,Vdd=5.4V
-1
uA
Vol
Low level output
Iol=2mA
0.4
Voh
High level output
Ioh=-2mA
0.7*Vdd
V
V
Vdd-0.4
AC characteristic
symbol
parameter
remark
min
typical
max
Unit
fref
PLL frequency
Parallel fundamental
10
12
MHz
frequency
315 MHz band,2.5KHz step
310.24
319.75
(10MHz crystal used)
430.24
439.75
868 MHz band,5KHz step
860.48
879.51
900.72
929.27
fLO
Tel: +86-755-82973805 Fax: +86-755-82973550
MHz
RFM01
Datasheet REV1.2
fLO
fLO
frequency
248.19
255.80
(8MHZ crystal used)
344.19
351.80
688.38
703.61
720.57
743.41
frequency
372.28
383.71
(12MHZ crystal used)
516.28
527.71
1032.5
1055.4
1080.8
1115.1
60
67
75
120
134
150
180
200
225
240
270
300
300
350
375
360
400
450
BW
Receiver bandwidth
tlock
PLL lock time
After 10MHz step hopping,
MHz
MHz
kHz
20
us
250
us
frequency error <10 kHz

Tst, p
PLL start time
After crystal stabilized
BR
Data rate
With internal digital
115.2
kbps
256
kbps
demodulator
BRA
Pmin
AFCrange
Data rate
sensitivity
AFC working range
With external RC filter

BW=134KHz,BR=1.2kbps,315MHz band
-109
-100
-109
-100
-105
-98
-105
-98
Ffsk: received signal
0.8*Ffsk
dBm
modulation depth
RSA
RSSI accuracy
dB
RSR
RSSI range
46
dB
CARSSI
ARSSI filter
nF
RSSTEP
RSSI programmable
dB
500
us
step
RSRESP
DRSSI response time
RSSI output high after valid ,

CARRSI=5nF
CXL
Capacitor bank
Programmable step with
8.5
16
pF
100
mS
096
108
mS
5*10E11
mS
mS
pF
10
ns
0.5pF step, +/- 10%

TPOR
PWR time
Vdd reach 90%
50
TPBT
Wakeup timer period
Calibrated each 30s
TWAKE-UP
Programmable
wakeup time
TSX
Crystal start up time
CIN,D
Load capacitance
Tr,F
Output rising edge
Crystal ESR < 100 Ohms
With 15PF load
Tel: +86-755-82973805 Fax: +86-755-82973550
RFM01
Datasheet REV1.2
Field testing range

Band
Test condition
Distance
433MHz band
Receiver bandwidth =134KHz, data rate=1.2kbps, transmitter

modulation=60KHZmatches with RF02B
>200M
In free open area

868MHz band
Receiver bandwidth=134KHz,data rate =1.2kbps

Transmitter modulation=60KHZmatches with RFM02Bin free
>200M
open area
915MHz band
Receiver bandwidth=134KHz,data rate =1.2kbps

Transmitter modulation=60KHZmatches with RFM02Bin free
>200M
open area
Mechanical Dimension
units in mm
SMD PACKAGES1
Tel: +86-755-82973805 Fax: +86-755-82973550
RFM01
Datasheet REV1.2
SMD PACKAGES2
DIP PACKAGED
Tel: +86-755-82973805 Fax: +86-755-82973550
RFM01
Datasheet REV1.2
Module Model Definition

model=module-operation_band-package_type
RFM01-433-D
module type
operation band
Package
Note: SMD packages is divided into two kinds based on thickness: 1. thickness is 4.2mm, 2. thickness is
2.2mm
example1RFM01 module at 433MHz band ,DIP: RFM01-433-D

2RFM01 module at 868MHZ band,SMD, thickness at 4.2mm: RFM01-868-S1
This document may contain preliminary information and is subject to
change by Hope Microelectronics without notice. Hope
Microelectronics assumes no responsibility or liability for any use of
HOPE MICROELECTRONICS CO.,LTD
the information contained herein. Nothing in this document shall
Add:4/F, Block B3, East Industrial Area,
operate as an express or implied license or indemnity under the
Huaqiaocheng,
intellectual property rights of Hope Microelectronics or third parties.
Shenzhen,
The products described in this document are not intended for use in
China
Tel:
86-755-82973805
Fax:
Email:
Guangdong,
86-755-82973550
sales@hoperf.com
trade@hoperf.com
Website: http://www.hoperf.com
http://www.hoperf.cn
implantation or other direct life support applications where malfunction

may result in the direct physical harm or injury to persons. NO
WARRANTIES OF ANY KIND, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MECHANTABILITY OR FITNESS
FOR A ARTICULAR PURPOSE, ARE OFFERED IN THIS
DOCUMENT.
http://hoperf.en.alibaba.com
2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.
Tel: +86-755-82973805 Fax: +86-755-82973550

RFM01

Uploaded by

Copyright:

Available Formats

RFM01

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RFM01

Uploaded by

Copyright:

Available Formats

RFM01

ISM BAND FSK RECEIVER MODULE

E-mail: sales@hoperf.com http://www.hoperf.com

Valid data indicator

Positive power supply

SPI data input

SPI clock input

Chip select (active low)

FIFO fill interrupt(active low) or status read data output

Reset outputactive low

Interrupts request outputactive low

Data input(non FIFO mode)/ FIFO select

interrupts(active high)when FIFO level set to 1, FIFO empty

Clock output for external microcontroller

Tel: +86-755-82973805 Fax: +86-755-82973550

E-mail: sales@hoperf.com http://www.hoperf.com

Positive power supply

All pin input level

Input current except power

Human body model

Recommended working range

Positive power supply

Sleep mode current

Low battery detection

Low battery step

Low battery detection

All blocks off

0.1V per step

Low level input

High level input

Low level output

High level output

315 MHz band,2.5KHz step

(10MHz crystal used)

433 MHz band,2.5KHz step

868 MHz band,5KHz step

915 MHz band,7.5KHz step

Tel: +86-755-82973805 Fax: +86-755-82973550

E-mail: sales@hoperf.com http://www.hoperf.com

315 MHz band,2.5KHz step

(8MHZ crystal used)

433 MHz band,2.5KHz step

868 MHz band,5KHz step

915 MHz band,7.5KHz step

315 MHz band,2.5KHz step

(12MHZ crystal used)

433 MHz band,2.5KHz step

868 MHz band,5KHz step

915 MHz band,7.5KHz step

PLL lock time

After 10MHz step hopping,

frequency error <10 kHz

PLL start time

After crystal stabilized

With internal digital

AFC working range

With external RC filter

Ffsk: received signal

DRSSI response time

RSSI output high after valid ,