Vibrating Screen

hin
Vibrating Screen
Vibrating Screen
Sc
ree
nO
fS
han
gh
ai
Zen
ith
Co
mp
any
Of
C
3YA1848 vibrating screen is vibrated by the circling motion. The screen line of
material is long and the screening specification is various. The screen of very
specification is clear. It adopts the tubbish vibrator and eccentric adjustment, with the
feature of strong vibration, high screening efficiency and small vibrating noise. This
machine is durable, easy to maintain, safe to use. So it is widely used in mining,
construction material, transportation, energy and chemical industry for classification.
Main characteristic (Model: 3YA1848)
Vib
rat
ing
Screen
mesh:
2
7.7m *3
Feeding size:
100mm
Double
amplitude:
8mm
Weight: 7100kg
Screen
1800*4800mm
specification:
Capacity: 30-75m3/h
Size of hole: 5-80mm

Vibrating
970r/min
Model and power of motor: Y180L-4, 18.5kw

Overall dimension: 5027*3100*3500mm
frequency:
hin
a
Vibrating Screen
Operating instruction
Vib
rat
ing
Sc
ree
nO
fS
han
gh
ai
Zen
ith
Co
mp
any
Of
C
The motor of the screening machine can be installed on the left or right. Please inform
us when ordering.
This machine is made up of screening case, supporting device, vibrator and gearing.
The tubbish vibrator is set up in the middle of the case. The vibrating force is changed
by adjusting the eccentric block to adjust the amplitude. Bearing is lubricated by
lubricating grease. The model of bearing is 3G3628Y. And SPC3150 high-efficiency
triangle belt is used for transmission.
The screening surface is the main structure of the machine. It should use wire netting
twisted by high grade and durable steel wire. The size of the hole controls the
classified size.
This machine is supplied with whole set after being assembled by us. Customers
should check and count the machine after receiving the machine to eliminate the
disadvantage during the transportation.
Erectors should be familiar with structure, performance and technical requirement.
They should make suitable installation rules.
There should be enough suspension setting. We should support the case with 120*120
sides wood when lifting on and off to avoid distortion. In order to avoid distortion of
screening frame and shatter of accessories, the machine can not be dragged on the
ground.
The screen should be installed on the firm armoured concrete base. The height,
intension and area should be calculated separately according to geology and usage.
The machine also can be installed on the steel shelf. Installation measurement can
refer to diagram.
The axis of the seat should be unanimous with that of spring bracket. There should be
enough space under the base for the installation of transmission and maintenance of
machine.
When installing feeding hopper and discharging valve, the clearance between feeding
hopper and case should be larger than 40mm, also the discharging valve with the case.
The upper and lower interval is larger than 80mm.
In order to reduce the impact caused by material, the fall should less than 200mm.
Before the test run, please check whether the installation of the spring bracket accords
with requirement. Check the quantity of the spring being pressed down to make sure
the height balance of the former, latter, left and right is less than 5mm. Fasten all the
fastener. Inject lubricating grease into the bearing. Inch first before test run. Then do
the non-load trial after conferring usual.
hin
a
Vibrating Screen
Precautions in the operation
Trouble and troubleshooting
Trouble
Reason
Zen
ith
Co
mp
any
Of
C
The machine should be grounded. The wire should be reliable and insulated. It should
be installed in the snakeskin pipe. Cut off the electricity when overhauling.
Turn on the machine when it is non-loaded. Overload is prohibited. Turn off the
machine when all material is screened and discharged. Do not adjust, clean; overhaul
the machine when it is under the work.
Under the normal working condition, grease the bearing every 8 hours. The vibrator
should use EL-3 lithium base grease for lubrication. Moreover do overall check on
time every month, including whether fixed parts are fastened, side plate is spitted,
crossbeam has crack. Also check the performance of spring, seal of vibrator,
transmission belt and power supply.
Sc
ree
nO
fS
han
gh
ai
1. The motor damages

2. The
electric
component damage
3. The
voltage
is
insufficient
The screen machine is
4. supplies pilling on the
unable to start or the
screen is too much
vibration is not enough
5. The vibrator breaks
down
6. The lubricating grease
is too thick.
7. The belt skids
Vib
rat
ing
1. The horizontal level of

the case is not right
2. The
rigidity
of
supporting spring are
too different or the
The flow of material runs
spring damage
unusually
3. The surface of the
screen damages
4. Feeding is not balance
5. The bracket of the
screen ruptured
Suggestion
1. Change the motor
2. Change the eclectic
component
3. Change the power to
supply
4. Clear up the supplies on
the surface
5. Overhaul the vibrator
6. Wash
the
vibrator,
upgrade or add the
suitable
lubricating
grease
7. Make the belt tight
1. Adjust the height of the
bracket
2. Change the spring
3. Change the screen mesh
4. Operate proportionally,
feed
the
material
steadily
5. Change the bracket of
screen mesh
1.
2.
The
temperature
bearing is high
of
3.
4.
1.
3.
Sc
ree
nO
fS
Notice
2.
1.
2.
3.
4.
Add lubricating grease

Reduce
lubricating
grease
Wash or change
Change bearing
Try to protect it by rubdown

or drill
han
The components, such as

board crossbeam of side
etc, are damaged
Of
C
4.
mp
any
3.
Co
There is unusual noise
1. Change the spring

2. Fasten the bolt
3. Change the bracket of
the screen mesh
4. Change the angle iron or
underprop
Zen
ith
2.
The
bearing
of
vibrator damages
The fastening bolts
of the screen loose
The bracket of the
screen ruptured
The bearing are
damaged
The
lubricating
grease is not enough
The
lubricating
grease is too much
The
lubricating
grease is dirty
The
bearing
damages
The material are
worn out seriously
The time for work
under
critical
frequency is too long
Gas cutting or gas
welding
other
accessories
gh
ai
1.
hin
a
Vibrating Screen
ing
Remove or install vibrator by pushing and pressing. Dont use hammer to knock on.
High strength bolt is fastened with torsion spanner or other methods.
M16 bolt
screw strength on
250N. mm
M20 bolt
screw strength on
550N. mm
Users can work out the operation regulation and safety regulation by themselves
according to their own requirement.
Vib
rat
Specification and performance of common screen
h
Of
C
Amplitude
Power
Weight
Overall dimension
7.5-70
7.5-80
7.5-80
50-208
50-250
50-300
50-350
100-500
150-700
800-970
800-970
800-970
970
970
970
970
730
730
8
8
8
8
8
8
8
8
8
5.5
5.5
7.5
15
15
18.5
22
30
30
1.75
2.34
3.05
5.33
6.07
6.93
7.7
9.24
12.35
3073*2030*1611
3122*2030*2247
3122*2050*2700
4400*2610*2857
5650*2528*3400
5027*3100*3500
6200*3325*3593
6374*3821*3707
6374*4121*3707
Sh
Of
mp
a ny
Frequency
Co
Capacity
ang
hai
1200*3000
1200*3000
1200*3000
1500*4200
1500*4800
1800*4800
1800*6000
2100*6000
2400*6000
Feedin
g size
200
200
200
400
400
400
400
400
400
Zen
ith
Specification
en
3.2
3.2
3.6
5.7
6.4
7.7
10.8
11.5
14.4
Size of
hole
3-50
3-50
3-50
5-50
5-50
5-80
5-80
5-100
5-150
cre
Area
gS
YA1230
2YA1230
3YA1230
2YA1542
3YA1548
3YA1848
3YA1860
2YA2160
2YA2460
Lay
er
1
2
3
2
3
3
3
2
2
tin
Model
Vibrating Screen

Vibrating Screen

Uploaded by

Copyright:

Available Formats

Vibrating Screen

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vibrating Screen

Uploaded by

Copyright:

Available Formats

What are the main components and functions of a vibrating screen?

What precautions should be taken when operating a vibrating screen?

hin

Main characteristic (Model: 3YA1848)

Size of hole: 5-80mm

Model and power of motor: Y180L-4, 18.5kw

Precautions in the operation

Trouble and troubleshooting

1. The motor damages

1. The horizontal level of

Add lubricating grease

Try to protect it by rubdown

The components, such as

There is unusual noise

1. Change the spring

Specification and performance of common screen

You might also like