Limit, Fit &tolerance

Limit, Fit &Tolerance
Tolerance is the total amount a dimension may vary and is the difference between the upper
(maximum) and lower (minimum) limits. Because it is impossible to make everything to an exact size,
tolerances are used on production drawings to control the parts.
When do we need tolerances?
In particular, tolerances are assigned to mating parts in an assembly. For example, in case, when the
slot in the part must accommodate another part. One of the great advantages of using tolerances is that
it allows for interchangeable parts, thus permitting the replacement of individual parts.
Tolerances can be expressed in several ways:
1. Direct limits, or as tolerance value supplied directly to a dimension.
2. Geometric tolerances, indicated by special symbols related to part surfaces.
3. Notes referring to specific conditions usually placed next to the corresponding dimensions.
Example: single limit tolerance
which limits either the maximum or minimum size of a feature or a space, leaving theother limit of size
unspecified.
4. A general tolerance note in the title block.
Plus and Minus Dimensions

With this approach the basic size is given, followed by a plus/minus sign and the tolerance value.
Tolerance can be unilateral or bilateral. A unilateral tolerance varies in only one direction,
while a bilateral tolerance varies in both directions from the basic size.If the variation is equal in
both directions, then the variation is preceded by a + symbol. The plus and minus approach can only be
used when the two variations are equal.
Important terms
Nominal size a dimension used to describe the general size, usually expressed in common
fractions. The slot in the figure has a nominal size of 1/2".
Basic size the theoretical size used as a starting point for the application of tolerances. The basic size
of the slot is .500"
Actual size the measured size of the finished part after machining. Here it is .501".
Limits the maximum and minimum sizes shown by the tolerance dimension. The slot in figure
has limits of .502 and .498, and the mating part has limits of .495 and .497.The larger value for each
part is the upper limit, and the smaller value is the lower limit
Allowance - is the minimum clearance or maximum interference between parts, or the
Tightest fit between two mating parts. In figure the allowance is .001, meaning that the tightest fit
occurs when the slot is machined to its smallest allowable size of .498 and the mating part is machined
to its largest allowable size of .497. The difference between .498 and .497, or .001, is the allowance.
Tolerance - is the total allowable variance in a dimension, which is the difference between the upper
and lower limits. The tolerance of the slot in Figure is .004" (.502 - .498 = .004) and the tolerance
of the mating part is.002" (.497 - .495 = .002)
Maximum material condition (MMC)
is the condition of a part when it contains the most amount of material. The MMC of an external feature
(such as a shaft) is the upper limit. The MMC of an internal feature(such as a hole) is the lower limit
Least material condition (LMC)
is the condition of a part when it contains the least amount of material possible. The LMC of an
external feature is the lower limit of the part. The LMC of an internal feature is the upper limit of the
part.
Fit types
The degree of tightness between mating parts is called the fit.
Clearance fit occurs when two tolerance mating parts will always leave a space or clearance when
assembled. In figure above, the largest that shaft A can be manufactured is .999, and the smallest the
hole can be is 1.000. The shaft will always be smaller than the hole, resulting in a minimum clearance
of +.001, also called an allowance .The maximum clearance occurs when the smallest shaft (.998) is
mated with the largest hole (1.001), resulting in a difference of +.003.
Interference fit
occurs when two tolerance mating parts will always interfere when assembled. An interference fit
fixes or anchors one part into the other, as though the two parts were one. In the figure, the smallest that
shaft B can be manufactured is 1.002, and the largest the hole can be manufactured is 1.001. This
means that the shaft will always be larger than the hole, and the minimum interference is -.001.The
maximum interference would occur when the smallest hole (1.000) is mated with the largest
shaft (1.003),resulting in an interference of -.003.In order to assemble the parts under this condition, it
would be necessary to stretch the hole or shrink the shaft or to use force to press the shaft into the hole.
This kind of fit can be used to fasten two parts together without the use of mechanical fasteners or
adhesive
Transition fit
occurs when two tolerance mating parts will sometimes be an interference fit and sometimes be
clearance fit when assembled. In the figure, the smallest the shaft can be manufactured is .998, and
the largest the hole can be manufactured is 1.001,resulting in a max clearance of +.003. The largest the
shaft can be manufactured is 1.002, and the smallest the hole can be is 1.000, resulting in a
max interference of -.002.
Metric limits and fits

The standards used for metric measurements are recommended by the International Standards
Organization (ISO).The terms used in metric tolerancing are as follows:
Basic Size the exact theoretical size to which limits of deviation are assigned and are the same for
both parts.
Deviation the difference between the size of the part and the basic size.
Upper deviation the difference between the maximum size limit and the basic size.
Lower deviation is the difference between the minimum limit of size and the basic size.
Fundamental deviation is the deviation closest to the basic size (for both parts). It is denoted by a
letter.
Tolerance is the difference between the maximum and minimum size limits on a part.
Tolerance zone represents the tolerance and its position in relation to the basic size.
International tolerance grade (IT) the classification system representing groups

of tolerances which varydepending upon the basic size, but have the same level of accuracy with a
given grade. It is denoted by thecombinations IT0, IT1, and IT01 to IT16 altogether 18 IT grades
For example, in the following figure with the notations of hole, shaft and their fit, the
numbers 7 and 8 are IT grades:
Hole basis
is the system of fits where the minimum hole size is the basic size. The fundamental deviation for
a hole basis system is indicated by the uppercase letter H.
Shaft basis
is the system of fits where the maximum shaft size is the basic size. The fundamental deviation for a
shaft basis system is indicated by the lowercase letter f
Tolerance is the total amount a dimension may vary and is the difference between the
upper(maximum) and lower (minimum) limits. Because it is impossible to make everything to an exact
size, tolerances are used on production drawings to control the parts
.
When do we need tolerances?
In particular, tolerances are assigned to mating parts in an assembly. For example, in case, when the
slot in the part must accommodate another part. One of the great advantages of using tolerances is that
it allows for interchangeable parts, thus permitting the replacement of individual parts.
http://www.scribd.com/marathonjohnb%20/d/21618126-Types-of-Shaft-Fit-and-Tolerances

Limit, Fit &tolerance

Uploaded by

Copyright:

Available Formats

Limit, Fit &tolerance

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Limit, Fit &tolerance

Uploaded by

Copyright:

Available Formats

Limit, Fit &Tolerance

Plus and Minus Dimensions

Metric limits and fits

International tolerance grade (IT) the classification system representing groups

You might also like