520l0344 Folletos

MAKING MODERN LIVING POSSIBLE
Technical Information
Proportional Valve Group

PVG 32
powersolutions.danfoss.com
PVG 32 Proportional Valve Group
Revision History
Table of Revisions
Date
Changed
Rev
Feb 2014
Spec. sheet update
HE
Jan 2014
Converted to Danfoss layout DITA CMS
HD
Feb 2006 - Aug 2013
Various changes
BA - HC
Jan 2005
New Edition
AA
520L0344 Rev HE Feb 2014
Contents
General description
Safety in application
Function
PVG 32 technical data
Electrical actuation
Features of PVG 32........................................................................................................................................................................... 6

PVG modules .....................................................................................................................................................................................6
PVP, pump side modules..........................................................................................................................................................6
PVB, basic modules.....................................................................................................................................................................7
Actuation modules..................................................................................................................................................................... 7
Remote control units ......................................................................................................................................................................7
PVG 32 with open center PVP (fixed displ. pump) PVB with flow control spool.....................................................8
PVG 32 with closed center PVP (variable displ. pump) PVB with flow control spool............................................ 9
PVG 32 sectional drawing........................................................................................................................................................... 10
Load sensing for variable displ. pump supply.....................................................................................................................11
Control system example..............................................................................................................................................................12
Typical wiring block diagram example.............................................................................................................................14
PVG32 Mainly used in system with fixed displacement pumps...........................................................................16
PVG100 Alternative LS dump or pilot supply disconnect...................................................................................... 16
PVG120 Pump disconnect/block for variable pumps.............................................................................................. 16
Load sensing controls...................................................................................................................................................................17
LS control with bleed orifice (do not use with PVG valves).......................................................................................17
Integral PC function................................................................................................................................................................. 17
Load sensing system characteristics:.................................................................................................................................17
Remote pressure compensated controls.............................................................................................................................. 17
Remote pressure compensated system characteristics:............................................................................................ 18
Typical applications for remote pressure compensated systems:..........................................................................18
PVG 32 main spool with pressure compensated control................................................................................................ 18
Pressure compensated system characteristics.............................................................................................................. 19
Typical applications for pressure compensated systems...........................................................................................19
PVPC adapter for external pilot oil supply............................................................................................................................ 20
PVPC with check valve for open center PVP................................................................................................................... 20
PVPC without check valve for open or closed center PVP.........................................................................................21
PVMR, friction detent....................................................................................................................................................................23
PVMF, mechanical float position lock.....................................................................................................................................23
PVBS, main spools for flow control (standard).................................................................................................................... 23
PVBS, main spools for flow control (linear characteristic)............................................................................................... 23
PVBS, main spools for pressure control................................................................................................................................. 24
Background.................................................................................................................................................................................24
Principle....................................................................................................................................................................................... 25
Application..................................................................................................................................................................................25
Sizing.............................................................................................................................................................................................26
Limitation.................................................................................................................................................................................... 26
PVPX, electrical LS unloading valve.........................................................................................................................................26
PVH, hydraulic actuation............................................................................................................................................................. 28
PVM, mechanical actuation........................................................................................................................................................28
PVE technical data......................................................................................................................................................................... 28
PVPX, electrical LS unloading valve.........................................................................................................................................31
Electrical control of PVG.............................................................................................................................................................. 32
Closed loop control....................................................................................................................................................................... 33
PVEO................................................................................................................................................................................................... 34
PVEM...................................................................................................................................................................................................35
PVEA, PVEH, PVES, PVEU.............................................................................................................................................................. 35
PVEP.................................................................................................................................................................................................... 35
PVED-CC and PVED-CX.................................................................................................................................................................35
520L0344 Rev HE Feb 2014
Contents
PVHC................................................................................................................................................................................................... 36
Technical characteristics
Hydraulic systems
Other operating conditions
Dimensions
General...............................................................................................................................................................................................38
PVP, pump side module.............................................................................................................................................................. 38
Pressure relief valve characteristic in PVP........................................................................................................................38
PVB, basic modules oil flow characteristics.......................................................................................................................... 38
Pressure-compensated PVB, open or closed center PVP .......................................................................................... 39
PVB without pressure compensation, open center PVP.............................................................................................40
PVB without pressure compensation, closed center PVP.......................................................................................... 42
PVLP, shock and PVLA, suction valves...............................................................................................................................43
Pressure build-up for pressure controlled spools.........................................................................................................44
Pressure control spool flow characteristics.......................................................................................................................... 45
Examples of how to use the characteristics for pressure control spools...................................................................45
Characteristics for float position main spools..................................................................................................................... 46
Manually actuated PVG 32 fixed displ. pump.................................................................................................................. 48
Electrically actuated PVG 32 variable displ. pump......................................................................................................... 49
Oil.........................................................................................................................................................................................................50
Mineral oil....................................................................................................................................................................................50
Non-flammable fluids............................................................................................................................................................. 50
Particle content, degree of contamination...........................................................................................................................50
Biodegradable oils....................................................................................................................................................................50
Filtration............................................................................................................................................................................................ 50
System filters.............................................................................................................................................................................. 50
Internal filters............................................................................................................................................................................. 51
PVM, control lever positions...................................................................................................................................................... 55
Surface treatment.......................................................................................................................................................................... 55
Modules symbols, description and code numbers

PVP, pump side modules.............................................................................................................................................................56
PVB, basic modules........................................................................................................................................................................58
PVLP, shock and suction valve (fitted in PVB)...................................................................................................................... 59
PVLA, suction valve (fitted in PVB)........................................................................................................................................... 60
PVM, mechanical actuation........................................................................................................................................................60
PVH, hydraulic actuation............................................................................................................................................................. 61
PVS, end plate..................................................................................................................................................................................61
PVAS, assembly kit.........................................................................................................................................................................62
PVPX, electrical LS unloaded valve.......................................................................................................................................... 62
PVPC, plug for external pilot oil supply..................................................................................................................................62
Module selection chart
Order specification
Standard FC spools........................................................................................................................................................................64
Standard FC spools, hydraulic actuation...............................................................................................................................65
FC spools for mechanical float position, PVMF................................................................................................................... 65
FC spools for friction detent, PVMR.........................................................................................................................................65
FC spools with linear flow characteristic .............................................................................................................................. 66
Standard PC spools .......................................................................................................................................................................67
Standard PC spools, hydraulic actuation...............................................................................................................................68
PVB, basic valves.............................................................................................................................................................................69
PVP, pump side module.............................................................................................................................................................. 70
PVE, electrical actuation.............................................................................................................................................................. 72
Please state.......................................................................................................................................................................................74
Standard and option assembly................................................................................................................................................. 74
520L0344 Rev HE Feb 2014
Contents
Reordering........................................................................................................................................................................................74
Pressure setting limits.................................................................................................................................................................. 74
PVG 32 order specification form...............................................................................................................................................76
520L0344 Rev HE Feb 2014
General description
PVG 32 is a hydraulic load sensing valve designed to give maximum flexibility. From a simple load sensing
directional valve, to an advanced electrically controlled load-independent proportional valve.
The PVG 32 modular system makes it possible to build up a valve group to meet requirements precisely.
The compact external dimensions of the valve remain unchanged whatever combination is specified.
Features of PVG 32
Load-independent flow control:
Oil flow to an individual function is independent of the load pressure of this function
Oil flow to one function is independent of the load pressure of other functions
Good regulation characteristics

Energy-saving
Up to 12 basic modules per valve group
Several types of connection threads
Low weight
Compact design and installation
PVG modules
PVP, pump side modules
Built-in pressure relief valve

Pressure gauge connection
Versions:
Open center version for systems with fixed displacement pumps

Closed center version for systems with variable displacement pumps
Pilot oil supply for electrical actuator built into the pump side module
Pilot oil supply for hydraulic actuation built into the pump side module
Versions prepared for electrical LS unloading valve PVPX
520L0344 Rev HE Feb 2014
General description
PVB, basic modules
Interchangeable spools
Depending on requirements the basic module can be supplied with:
Integrated pressure compensator in channel P

Load holding check valve in channel P
Shock/suction valves for A and B ports
LS pressure limiting valves individually adjustable for ports A and B
Different interchangeable spool variants
All versions suitable for mechanical, hydraulic and electrical actuation
Actuation modules
The basic module is always fitted with mechanical actuator PVM and PVMD, which can be combined with
the following as required:
Electrical actuator (11 - 32 V ===):
PVES proportional, Super

PVEH proportional, High performance
PVEH-F proportional high performance, Float
PVEA proportional low hysteresis
PVEM proportional, Medium performance
PVEO ON/OFF
PVEU proportional, voltage control, 0-10 V
PVED-CC Digital CAN controlled J1939/ISOBUS
PVED-CX Digital CAN controlled CANopen X-tra safety
PVEP PWM voltage controlled (11-32 V)
PVHC High Current actuator for PVG
PVMF, cover for Mechanical Float
Electrical remote control units:
PVMR, cover for Mechanical detent

PVH, cover for Hydraulic actuation
Remote control units
PVRE, PVRET
PVREL
PVRES
Prof 1
Prof 1 CIP
JS120
JS1000 Ball grip

JS1000 PRO grip
JS2000
JS6000
JS7000
Hydraulic remote control unit: PVRHH
520L0344 Rev HE Feb 2014
General description
Electrical and hydraulic remote control units
PVRE, electrical control unit, 162F
PVRH, hydraulic control unit, 155N
155N0003
PVREL, electrical control unit, 155U
155N0001
155N0004 155N0005 155N0002
PVRES, electrical control unit, 155B
Prof 1, 162F
PVG 32 with open center PVP (fixed displ. pump) PVB with flow control spool
When the pump is started and the main spools in the individual basic modules (11) are in the neutral
position, oil flows from the pump, through connection P, across the pressure adjustment spool (6) to
tank. The oil flow led across the pressure adjustment spool determines the pump pressure (stand-by
pressure).
When one or more of the main spools are actuated, the highest load pressure is fed through the shuttle
valve circuit (10) to the spring chamber behind the pressure adjustment spool (6), and completely or
partially closes the connection to tank to maintain pump pressure.
Pump pressure is applied to the right-hand side of the pressure adjustment spool (6).
The pressure relief valve (1) will open should the load pressure exceed the set value, diverting pump flow
back to tank.
In a pressure-compensated basic module the compensator (14) maintains a constant pressure drop
across the main spool both when the load changes and when a module with a higher load pressure is
actuated.
With a non pressure-compensated basic module incorporating a load drop check valve (18) in channel P,
the check valve prevents return oil flow.
The basic module can be supplied without the load drop check valve in channel P for functions with overcenter valves.
The shock valves PVLP (13) with fixed setting and the suction valves PVLA (17) on ports A and B are used
for the protection of the individual working function against overload and/or cavitation.
An adjustable LS pressure limiting valve (12) can be built into the A and B ports of pressure-compensated
basic modules to limit the pressure from the individual working functions.
520L0344 Rev HE Feb 2014
General description
Please see the sectional drawing below for better understanding of this example.
The LS pressure limiting valves save energy compared with the shock valves PVLP:
with PVLP all the oil flow to the working function will be led across the combined shock and suction
valves to tank if the pressure exceeds the fixed setting.
with LS pressure limiting valves an oil flow of about 2 l/min [0.5 US gal/min] will be led across the LS
pressure limiting valve to tank if the pressure exceeds the valve setting.
PVG 32 with closed center PVP (variable displ. pump) PVB with flow control spool
In the closed center version of PVP an orifice (5) and a plug (7) have been fitted instead of the plug (4).
This means that the pressure adjustment spool (6) will only open to tank when the pressure in channel P
exceeds the set value of the pressure relief valve (1).
In load sensing systems the load pressure is led to the pump control via the LS connection (8).
In the neutral position the pump load sense control sets the displacement so that leakage in the system is
compensated, to maintain the set stand-by pressure.
When a main spool is actuated the pump load sense control will adjust the displacement so that the set
differential pressure (margin) between P and LS is maintained.
The pressure relief valve (1) in PVP should be set at a pressure of approx. 30 bar [435 psi] above maximum
system pressure (set on the pump or external pressure relief valve).
520L0344 Rev HE Feb 2014
General description
PVG 32 sectional drawing
1
4+5
A
LS
8
9
12 7
13
11
10
14
16
LS B
P LS A
17 15
A
19
18
20
V310106.A
10
1 Pressure relief valve
11 Main spool
2 Pressure reduction valve for pilot oil supply
12 LS pressure limiting valve
3 Pressure gauge connection
13 Shock and suction valve, PVLP
4 Plug, open center
14 Pressure compensator
5 Orifice, closed center
15 LS connection, port A
6 Pressure adjustment spool
16 LS connection, port B
7 Plug, closed center
17 Suction valve, PVLA
8 LS connection
18 Load drop check valve
9 LS signal
19 Pilot oil supply for PVE
10 Shuttle valve
20 Max. oil flow adjustment screws for A/B ports
520L0344 Rev HE Feb 2014
General description
Load sensing for variable displ. pump supply
The pump receives fluid directly from the reservoir through the inlet line. A screen in the inlet line
protects the pump from large contaminants.
The pump outlet feeds directional control valves such as PVG-32, hydraulic integrated circuits (HIC), and
other types of control valves.
The PVG valve directs and controls pump flow to cylinders, motors and other work functions. A heat
exchanger cools the fluid returning from the valve. A filter cleans the fluid before it returns to the
reservoir.
Flow in the circuit determines the speed of the actuators. The position of the PVG valve spool determines
the flow demand. A hydraulic pressure signal (LS signal) communicates demand to the pump control.
The pump control monitors the pressure differential between pump outlet and the LS signal, and
regulates servo pressure to control the swashplate angle. Swashplate angle determines pump flow.
Actuator load determines system pressure. The pump control monitors system pressure and will decrease
the swashplate angle to reduce flow if system pressure reaches the pump control setting.
A secondary system relief valve in the PVG valve acts as a back-up to control system pressure.
Pictorial circuit diagram
K/LFrame Series 45
open circuit axial
piston pump with
load sensing contro l
Double-ac ting cylinder
PVG 32
multi-sec tion
load
sensing
contro l
valve
Bi-directional
gear moto r
System pressur e
Servo pressur e
Heat exchanger
Reservoir
Filter
Actuator pressur e
Load sense pressur e
Actuator retur n
P101 658E
520L0344 Rev HE Feb 2014
Suction / case drain /

system retur n
11
All makes and all types of control valves (incl. proportional valves) can fail, thus the necessary protection
against the serious consequences of function failure should always be built into the system. For each
application an assessment should be made for the consequences of pressure failure and uncontrolled or
blocked movements.
To determine the degree of protection that is required to be built into the application, system tools such
an FMEA (Failure Mode and Effect Analysis) and Hazard and Risk Analysis can be used.
FMEA IEC EN 61508
FMEA (Failure Mode and Effect Analysis) is a tool used for analyzing potential risks. This analytical
technique is utilized to define, identify, and prioritize the elimination or reduction of known and/or
potential failures from a given system before it is released for production. Please refer to IEC FMEA
Standard 61508.
Hazard and Risk Analysis ISO 12100-1 / 14121
This analysis is a tool used in new applications as it will indicate whether there are special safety
considerations to be met according to the machine directives EN 13849. Dependent on the determined
levels conformity this analysis will detirmine if any extra requirements for the product design,
development process, production process or maintenance, i.e. the complete product life cycle.
W Warning
All makes/brands and types of directional control valves inclusive proportional valves can fail and
cause serious damage. It is therefore important to analyze all aspects of the application.
Because the proportional valves are used in many different operation conditions and applications,
the manufacturer of the application is alone responsible for making the final selection of the products
and assuring that all performance, safety and warning requirements of the application are met.
The process of choosing the control system and safety levels is governed by the machine directives
EN 13849 (Safety related requirements for control systems).
Control system example
Example of a control system for manlift using PVE Fault monitoring input signals and signals from
external sensors to ensure the PLUS+1 main controllers correct function of the manlift.
12
520L0344 Rev HE Feb 2014
Control system example
Legend:
1 Main power supply
2 Emergency stop/man present switch
3 HMI/Joystick control
4 Movement detection sensors
5 Main controller
6 PVG control valve
7 Hydraulic deactivation
520L0344 Rev HE Feb 2014
13
Electrical block diagram for above illustration
Main power supply

(battery)
Emergency stop and

Man present switch
HMI / Joystick
Joystick
neutral switch
Control
Signal
Motion detection sensor

Main control valve
Supply
Main controller
Neutral Supply
Detection Control
Signal
Conditioning
Signal
Conditioning
Fault
Monitoring
PVE fault output
Failure
Detection
PVE
Hydraulic deactivation
P301 317
Warning
It is the responsibility of the equipment manufacturer that the control system incorporated in the
machine is declared as being in conformity with the relevant machine directives.
Typical wiring block diagram example

Example of a typical wiring block diagram using PVEH with neutral power off switch and fault monitoring
output for hydraulic deactivation.
14
520L0344 Rev HE Feb 2014
Typical wiring block diagram example
A
Emergency
stop
PVE 1
C
Man present
switch
Neutral detection / Supply control
PVEH
with AMP
connector
US
UDC2
1)
signal
neutral
OFF
Delay
PVE 2
C
PVEH
Neutral detection / Supply control
with AMP
connector
US
UDC2
1)
signal
neutral
Error
OFF
Delay
E1
Error
E2
2) Alarm
logic
Output
OR
3) Memory
AND
high=on
low=off
Fault detection output
Hydraulic
deactivation
P301 318
A Emergency stop / man present switch

B PVE Faultmonitoring signals
C Neutral signal detection.
D Hydraulic deactivation
System Control Logic e.g. PLUS+1 for signal monitoring and triggering signal for deactivation of the
hydraulic system.
Warning
It is the responsebilty of the equipment manufacturer that the control system incorporated in the
machine is declared as being in confirmity with the relevant machine directives.
520L0344 Rev HE Feb 2014
15
PVG32 Mainly used in system with fixed displacement pumps
PVSK, commonly used in crane application - full flow dump

PVPX, LS dump to tank
PVG100 Alternative LS dump or pilot supply disconnect
PVPP, pilot oil supply shut off

External cartridge valve connecting LS Pressure to Tank
External cartridge valve connecting main Pressure to Tank
PVG120 Pump disconnect/block for variable pumps
16
PVPE, full flow dump for the PVG 120

External cartridge valve connecting LS Pressure to Tank
520L0344 Rev HE Feb 2014
Function
Load sensing controls
The LS control matches system requirements for both pressure and flow in the circuit regardless of the
working pressure. Used with a closed center control valve, the pump remains in low-pressure standby
mode with zero flow until the valve is opened. The LS setting determines standby pressure.
Typical operating curve
Load sensing circuit
PC setting
Flow
Q max
Pressure
P101 968E
P101 967
Most load sensing systems use parallel, closed center, control valves with special porting that allows the
highest work function pressure (LS signal) to feed back to the LS control.
Margin pressure is the difference between system pressure and the LS signal pressure. The LS control
monitors margin pressure to read system demand. A drop in margin pressure means the system needs
more flow. A rise in margin pressure tells the LS control to decrease flow.
LS control with bleed orifice (do not use with PVG valves)
The load sense signal line requires a bleed orifice to prevent high-pressure lockup of the pump control.
Most load-sensing control valves include this orifice. An optional internal bleed orifice is available, for use
with control valves that do not internally bleed the LS signal to tank.
Integral PC function
The LS control also performs as a PC control, decreasing pump flow when system pressure reaches the PC
setting. The pressure compensating function has priority over the load sensing function.
For additional system protection, install a relief valve in the pump outlet line.
Load sensing system characteristics:
Variable pressure and flow

Low pressure standby mode when flow is not needed
System flow adjusted to meet system requirements
Lower torque requirements during engine start-up
Single pump can supply flow and regulate pressure for multiple circuits
Quick response to system flow and pressure requirements
Remote pressure compensated controls

The remote PC control is a two-stage control that allows multiple PC settings. Remote PC controls are
commonly used in applications requiring low and high pressure PC operation.
520L0344 Rev HE Feb 2014
17
Function
Closed center circuit with remote PC
PC setting
Remote PC setting
Flow
Q max
Pressur e
P101 969E
P101 966
The remote PC control uses a pilot line connected to an external hydraulic valve. The external valve
changes pressure in the pilot line, causing the PC control to operate at a lower pressure. When the pilot
line is vented to reservoir, the pump maintains pressure at the load sense setting.
When pilot flow is blocked, the pump maintains pressure at the PC setting. An on-off solenoid valve can
be used in the pilot line to create a low-pressure standby mode. A proportional solenoid valve, coupled
with a microprocessor control, can produce an infinite range of operating pressures between the low
pressure standby setting and the PC setting.
Size the external valve and plumbing for a pilot flow of 3.8l/min [1US gal/min]. For additional system
protection, install a relief valve in the pump outlet line.
Remote pressure compensated system characteristics:
Constant pressure and variable flow

High or low pressure standby mode when flow is not needed
System flow adjusts to meet system requirements
Single pump can provide flow to multiple work functions
Typical applications for remote pressure compensated systems:
Modulating fan drives

Anti-stall control with engine speed feedback
Front wheel assist
Road rollers
Combine harvesters
Wood chippers
PVG 32 main spool with pressure compensated control

The PC control maintains constant system pressure in the hydraulic circuit by varying the output flow of
the pump. Used with a closed center control valve, the pump remains in high pressure standby mode at
the PC setting with zero flow until the function is actuated.
18
520L0344 Rev HE Feb 2014
Function
Simple closed center circuit
PC setting
Flow
Q max
0
0
Pressur e
P101 166E
P101 965
Once the closed center valve is opened, the PC control senses the immediate drop in system pressure
and increases pump flow by increasing the swashplate angle.
The pump continues to increase flow until system pressure reaches the PC setting.
If system pressure exceeds the PC setting, the PC control reduces the swashplate angle to maintain
system pressure by reducing flow. The PC control continues to monitor system pressure and changes
swashplate angle to match the output flow with the work function pressure requirements.
If the demand for flow exceeds the capacity of the pump, the PC control directs the pump to maximum
displacement. In this condition, actual system pressure depends on the actuator load.
For additional system protection, install a relief valve in the pump outlet line.
C Caution
Do not use the PVG 32 with LB control.
Pressure compensated system characteristics
Constant pressure and variable flow

High pressure standby mode when flow is not needed
System flow adjusts to meet system requirements
Single pump can provide flow to multiple work functions
Typical applications for pressure compensated systems
Constant force cylinders (bailers, compactors, refuse trucks)

On/off fan drives
Drill rigs
Sweepers
Trenchers
520L0344 Rev HE Feb 2014
19
Function
PVPC adapter for external pilot oil supply
PVPC with check valve for open center PVP
PVPC with check valve is used in systems where it is necessary to operate the PVG 32 valve by means of
the electrical remote control without pump flow. When the external solenoid valve is opened, oil from
the pressure side of the cylinder is fed via the PVPC through the pressure reducing valve to act as the
pilot supply for the electrical actuators. This means that a load can be lowered by means of the remote
control lever without starting the pump.
The built-in check valve prevents the oil from flowing via the pressure adjustment spool to tank. With the
pump functioning normally the external solenoid valve is closed to ensure that the load is not lowered
due to the pilot supply oil flow requirement of approximately 1 l/min [0.25 US gal/min]. With closed
center PVP the external pilot oil supply can be connected to the pressure gauge connection without the
use of a PVPC plug.
PVPC with check valve for OC PVP
20
520L0344 Rev HE Feb 2014
Function
Hydraulic diagram
PVPC without check valve for open or closed center PVP

PVPC without check valve is used in systems where it is necessary to supply the PVG 32 valve with oil
from a manually operated emergency pump without directing oil flow to the pilot oil supply (oil
consumption about 0.5 l/min) [0.13 US gal/min].
When the main pump is working normally, the oil is directed through the PVPC plug via the pressure
reduction valve to the electrical actuators.
520L0344 Rev HE Feb 2014
21
Function
PVPC without check valve OC/CC PVP
Hydraulic diagram
22
520L0344 Rev HE Feb 2014
Function
When the main pump flow fails, the external shuttle valve ensures that the oil flow from the manually
operated emergency pump is used to pilot open the over center valve and lower the load. The load can
only be lowered using the mechanical operating lever of the PVG 32 valve.
PVMR, friction detent
The friction detent PVMR allows the directional
spool to be held in any position, resulting in
infinitely variable, reversible, pressure
compensated flow.
This can be sustained indefinitely without having

to continue to hold the mechanical lever.
Friction detent spool position may be affected by
high differential actuator flow forces and system
vibration resulting in work function flow reduction.
PVMF, mechanical float position lock

Allows the float spool to be held in the float position after release of the mechanical handle.
PVMF, standard mount only
PVMF, optional mount only
P A F (Push-in)
P A F (Pull-out)
PVBS, main spools for flow control (standard)

When using standard flow control spools, the pump pressure is determined by the highest load pressure.
This is done either via the pressure adjustment spool in open center PVP (fixed displacement pumps) or
via the pump control (variable displacement pumps).
In this way the pump pressure will always correspond to the load pressure plus the stand-by pressure of
the pressure adjustment spool or the pump control. This will normally give optimum and stable
adjustment of the oil flow.
PVBS, main spools for flow control (linear characteristic)
PVBS main spools with linear characteristic have less dead band than standard spools and a proportional
ratio between control signal and oil flow in the range beyond the dead band. PVBS with linear
characteristic must never be used together with PVEM electrical actuators.
520L0344 Rev HE Feb 2014
23
Function
The interaction between the small dead band of the spools and the hysteresis of the PVEM actuator of
20% involves a risk of building up a LS pressure in neutral position.
In a few systems load sensing pump pressure may result in unstable adjustment of the oil flow and a
tendency towards system hunting.
This may be the case with working functions that have a large moment of inertia or over-center valves. In
such systems main spools for pressure control can be advantageous.
PVBS, main spools for pressure control
The spools are designed in such a way that the pump pressure is controlled by the spool travel. The main
spool must be displaced until the pump pressure just exceeds the load pressure before the working
function is applied. If the main spool is held in this position, the pump pressure will remain constant
even if the load pressure changes giving a stable system.
The use of pressure control spools, however, also means that:
the oil flow is load dependent

the dead band is load dependent
the pump pressure can exceed the load pressure by more than is usual
the pressure drop across main spool varies (energy consumption)
Due to these factors it is recommended that pressure control spools are only used when it is known for
certain that problems with stability will arise or already have arisen, and in applications where constant
pressure is needed e.g. drill holding.
Background
Instability in load sense control systems in certain applications with oscillations in the range of 1/2 - 2 Hz
can cause severe instability problems while trying to control functions in an application.
Critical applications are usually related to functions with an important inertia torque and/or functions
with secondarily fitted pressure controlled components e.g. over-center valves.
Examples:
a slewing function
main lifting/lowering function of a crane
The problem usually manifests itself in prolonged oscillation phenomena (Fig. 1), in a relatively constant
sequence of oscillations (Fig. 2) or in the worst case in an amplified sequence of oscillations (Fig. 3).
Fig. 1 Prolonged sequence
P
Fig. 2 Constant sequence
Prolonged sequence
time
Fig. 3 Amplified sequence
Constant sequence
time
Amplified sequence
time
P005 627E
To control the oscillation phenomena the "pressure control spool" was developed and is a patented
system which can minimize most of the oscillation issues.
24
520L0344 Rev HE Feb 2014
Function
Principle
The idea was to create a system operating independently of a constantly changing load pressure.
Therefore, we changed the well-known LS principle (Fig. 4), so that compensated pump pressure is part
of the LS system (Fig. 5) after the pressure compensator and before the metering range of the main spool.
Upon actuation of the spool, it will be led via a fixed and a variable orifice.
Fig. 4 Flow controlled spool
Fig. 5 Pressure controlled spool
P005 625
The opening area of the variable orifice is at

maximum at initial actuation and 0 at full stroke of
the spool and then the pressure created between
the two orifices is led into the LS system in the
usual way.
P005 626
Pump pressure vs. spool travel curve
In this way the pump pressure is built up

depending on the spool travel, i.e. the spool will
then have to be stroked to a position that the
pump pressure is higher than the actual load
pressure to make the oil flow from PA/B. When
the load changes for a fixed spool position the flow
to for the function will also change.
The valve section is now a load-dependent valve,
but ensuring a constant pump pressure which is
important in obtaining a stable function.
Application
Pressure controlled spools should in principle only be used when you have stability issues. Typical
applications on a crane:
Lifting/lowering movement
Slewing movement with cylinders
For the main lifting/lowering function on a crane it is recommended to fit a "half" pressure control
spool. This means that the spool is designed with a normal flow control on the lifting port and
pressure control connected to the port where the pilot signal to the over-center valve is acting. You
will thus maintain a load-independent lifting movement and achieve a stable but load-depending
lowering movement.
As the load pressure on slewing movements is usually steady - irrespective of the crane being loaded
or not it will be advantageous to use a "full" pressure control spool for A and B port.
In both cases we recommend the use of a basic valve, PVB, with pressure compensator. The pressure
compensator will ensure the individual load-independency between the basic valves.
It is further recommended to use the LS pressure relief valves as not only will they ensure individual
pressure limitation but also make it possible to adjust the maximum oil flow to the function.
520L0344 Rev HE Feb 2014
25
Function
It is not recommended to use shock valves as pressure limiting valves in connection with pressure control
spools.
Sizing
The size of "half" (e.g: P - A = flow control P - B pressure control) pressure control spools is determined on
basis of max. flow demand on the lifting port. If e.g. a max. pressure compensated flow of 65 l/min for the
lifting movement, you choose a 65 L/min spool (size D). The metering characteristic has then a given size.
As it is often requested to limit the use of the crane boom for downward push/force mode and the LS
pressure limitation can be used. It will appear from the characteristics enclosed what effect a pressure
limitation, PLS will have on max. flow on the lowering port.
The size for a "full" pressure control spool is determined on basis of known load pressure, PLS max, and
requested max. flow.
It will appear from the characteristics enclosed that if the load PLS is low and the pump pressure, Pp, is
high as a result of max. stroked spool you will get a large flow.
If PLS is approaching PLS max. the flow will be reduced and the dead band increased. Max. oil flow can be
reduced by approx. 50% without limiting max. pressure.
The reduction is made by limiting the spool travel from 7 mm to 5.5 mm.
Limitation
If a pressure controlled spool is chosen for stability reasons consideration should be made to features
related to the pressure control principle.
Deadband will change according to the load conditions and the valve section will become loaddependent and that the pump pressure may exceed the load pressure.
With all of the above in mind, a pressure controlled spool will minimize oscillation and obtain a stable
function that can be controlled smooth and precise.
PVPX, electrical LS unloading valve
PVPX is a solenoid LS unloading valve. PVPX is fitted into the pump side module enabling a connection to
be made between the LS and the tank lines. Thus the LS signal can be relieved to tank by means of an
electric signal.
For a PVP pump side module in open center version the relief to tank of the LS signal means that the
pressure in the system is reduced to the sum of the tank port pressure plus the neutral flow pressure for
the pump side module.
For a PVP pump side module in closed center version the relief to tank of the LS signal means that the
pressure is reduced to the sum of the tank port pressure for the pump side module plus the stand-by
pressure of the pump.
26
520L0344 Rev HE Feb 2014
The characteristics in this catalog are typical measured values. During measuring a mineral based
hydraulic oil with a viscosity of 21 mm2/s [102 SUS] at a temperature of 50 C [122 F] was used.
Max. pressure
Oil flow rated
Port P continuous1)
350 bar
[5075 psi]
Port P intermittent 5)
400 bar
[5800 psi]
Port A/B continous
350 bar
[5075 psi]
Port A/B intermittent 5)
420 bar
[6090 psi]
Port T, static/dynamic
25/40 bar
[365/580 psi]
Port P3) 4)
140/230 l/min
[37/61 US gal/min]
Port A/B, with press. comp.2)
100 l/min
[26.4 US gal/min]
Port A/B witout press. comp.
125 l/min
[33 US gal/min]
7 mm
[ 0.28 in]
Spool travel, standard

Spool travel, float position
Proportional range
4.8 mm
0.19 in]
Float position
8 mm
[ 0.32 in]
Standard
1.5 mm
[ 0.06 in]
Linear characteristic
0.8 mm
[ 0.03 in]
Max. internal leakage

at 100 bar [1450 psi] and 21 mm2/s [102 SUS]
A/B T without shock valve
20 cm3/min
[1.85 in3/min]
A/B T with shock valve
25 cm3/min
[2.15 in3/min]
Oil temperature
(inlet temperature)
Recommended temperature
30 60 C
[86 140F]
Min. temperature
-30 C
[-22 F]
Dead band, flow control spools
+90 C
[194 F]
Ambient temperature
Max. temperature
-30 60 C
[-22 140 F]
Oil viscosity
Operating range
12 - 75 mm2/s
[65 - 347 SUS]
Min. viscosity
4 mm2/s
[39 SUS]
Max. viscosity
460 mm2/s
[2128 SUS]
Max. contamination
(ISO 4406)
23/19/16
23/19/16
5 l/min
[0.13 US gal/min]
Filtration
(See chapter Filtration)
Oil consumtion in pilot oil pressure reduction valve
1) With PVSI end plate. With PVS end plate max. 300 bar [4351 psi].
2) For 130 l/min contact Danfoss Product Application Engineering.
3) In open circuit systems with short P-hoses/tubes, attention should be paid to pressure peaks at flows
>100 l/min [26.4 US gal/min] .
4) For system with mid inlet PVPVM.
5) Intermittent pressure at max. 250,000 cycles of full PVG life time cycles, with PVSI end plate. The
maximum intermittent pressure at max. 250,000 cycles stresses the need to confirm application duty
cycle before proceeding with specification. For further information contact Danfoss Product Application
Engineering.
Rated Pressure
Product
Maximum continuous P-port pressure
PVG 32 with PVS
300 bar [4351 psi]
PVG 32 with PVSI
350 bar [5076 psi]
520L0344 Rev HE Feb 2014
27
Rated Pressure (continued)

Product
Maximum continuous P-port pressure
PVG 32 with PVBZ
250 bar [3626 psi]
PVG 32 with HIC steel
350 bar [5076 psi]
PVG 32 with HIC aluminium
210 bar [3046 psi]
PVG 120/32 with PVS
300 bar [4351 psi]
PVG 120/32 with PVSI
350 bar [5076 psi]
PVG 100/32 with PVS
300 bar [4351 psi]
PVG 100/32 with PVSI
350 bar [5076 psi]
PVH, hydraulic actuation

Technical data for PVH
Control range pressure
5 15 bar [75 220 psi]
Max. pilot pressure
30 bar [435 psi]
Max. pressure on port T

(The hydraulic remote control lever should be connected directly to
tank.)
10 bar [145 psi]
PVM, mechanical actuation

Technical data for PVM
Spool displacement
Operating Torque Nm [lbfin]

PVM + PVMD
PVM + PVE
PVM + PVH
PVM + PVMR
PVM+PVMF
from neutral position
2.2 0.2
[19.5 1.8]
2.2 0.2
[19.5 1.8]
2.5 0.2
[22.1 1.8]
17
[3.8]
22
[5.0]
max. spool travel
2.8 0.2
[24.8 1.8]
2.8 0.2
[24.8 1.8]
6.9 0.2
[61.0 1.8]
into float position
60 [13.5]
away from float position
28 [6.3]
from any other position
8.5 [73.3]
Control lever position
No
2x6
Control range
control lever
19.5
proportional
13.4
float position
22.3
For PVE please see the PVE, Series 4 for PVG 32/100/120 Technical Information, 520L0553.
PVE technical data
Technical data for PVEO and PVEM
Supply voltage UDC
Current consumption at rated voltage
28
520L0344 Rev HE Feb 2014
rated
12 VDC
24 VDC
range
11 V to 15 V
22 V to 30 V
max. ripple
5%
0.65 A @ 12 V
0.33 A @ 24 V
Technical data for PVEO and PVEM (continued)

Signal voltage (PVEM)
neutral
0.5 x UDC
A-port B-port
0.25 UDC to 0.75 UDC
Signal current at rated voltage (PVEM)
0.25 mA
Input impedance in relation to 0.5 UDC
12 K
Power consumption
8W
0.50 mA
Reaction time for PVEO and PVEM

Supply voltage
Function
Disconnected by means of
neutral switch
Reaction time from neutral

position to max. spool travel
Disconnected by means
of neutral switch
Constant voltage
Reaction time from max.

spool travel to neutral
position
position to max. spool
position
Constant voltage
Reaction time from max.

spool travel to neutral
position
Hysteresis *
PVEO,
On/Off
PVEO-R,
On/Off
PVEM, Prop.
med.
max.
0.235 s
0.41 s
0.700 s
rated
0.180 s
0.35 s
0.450 s
min.
0.120 s
0.25 s
0.230 s
max.
0.175 s
0.33 s
0.175 s
rated
0.090 s
0.27 s
0.090 s
min.
0.065 s
0.25 s
0.065 s
max.
0.700 s
rated
0.450 s
min.
0.230 s
max.
0.700 s
rated
0.450 s
min.
0.230 s
rated
20%
* Hysteresis (control signal/spool travel) is indicated at rated voltage and f = 0.02 Hz for one cycle.
(one cycle = neutral full A full B neutral)
Technical data for PVEA, PVEH and PVES
PVEA, PVEH and PVES
Supply voltage UDC
rated
11 V to 32 V
range
11 V to 32 V
max. ripple
5%
Current consumption at rated voltage
PVEH/PVES (PVEA)
0.57 (33) A @ 12 V
Signal voltage
neutral
0.5 x UDC
A-port B-port
0.25 UDC to 0.75 UDC
Signal current at rated voltage
0.25 mA to 0.70 mA
Input impedance in relation to 0.5 UDC
12 K
Input capacitor
0.3 (17) A @ 24 V
100 F
Power consumption
PVEH/PVES (PVEA)
7 (3.5) W
(PVEH/PVES)
Max. load
100 mA
Active
Reaction time at fault
500 ms (PVEA: 750 ms)
Passive
Reaction time at fault
250 ms (PVEA: 750 ms)
520L0344 Rev HE Feb 2014
60 mA
29
Reaction time for PVEA, PVEH and PVES

Supply voltage
Function
of neutral switch

of neutral switch
Constant voltage
Constant voltage
Reaction time from max. spool

travel to neutral position

Reaction time from max. spool

travel to neutral position
Hysteresis *
PVEA
Prop. fine
s
PVEH
Prop. high
s
PVES
Prop. super
s
max.
0.50
0.23
0.23
rated
0.32
0.15
0.15
min.
0.25
0.12
0.12
max.
0.55
0.175
0.175
rated
0.40
0.09
0.09
min.
0.30
0.065
0.065
max.
0.50
0.20
0.20
rated
0.32
0.12
0.12
min.
0.25
0.05
0.05
max.
0.25
0.10
0.10
rated
0.20
0.09
0.09
min.
0.15
0.065
0.065
rated
2%
4%
0%
Typical hysteresis characteristics for control signal vs spool travel af different PVE types*
Spool position
* Hysteresis (control signal/spool travel) is indicated at rated voltage and f = 0.02 Hz. (one cycle = neutral
full A full B neutral)
The following technical data are from typical test results. For the hydraulic system a mineral based
hydraulic oil with a viscosity of 21 mm2/s [102 SUS] and a temperature of 50 C [122 F] were used.
Pilot oil consumption PVEA, PVEH, PVES, PVEO and PVEM
Function
PVEA
Prop. fine
PVEH
Prop. high
PVES
Prop. super
PVEO
ON/OFF
PVEM
Prop. medium
Neutral without
supply voltage
0.3 l/min
[0.079 US gal/min]
Locked with supply

voltage
0.4 l/min
[0.106 US gal/min]
0.1 l/min
[0.026 US gal/min]
0.1 l/min
[0.026 US gal/min]
0.1 l/min
[0.026 US gal/min]
0.1 l/min
[0.026 US gal/min]
30
520L0344 Rev HE Feb 2014
Pilot oil consumption PVEA, PVEH, PVES, PVEO and PVEM (continued)
Function
PVEA
Prop. fine
PVEH
Prop. high
PVES
Prop. super
PVEO
ON/OFF
PVEM
Prop. medium
0.7 l/min
[0.185 US gal/min]
0.8 l/min
[0.211 US gal/min]
0.7 l/min
[0.185 US gal/min]
0.5 l/min
[0.132 US gal/min]
One actuation (neutral 2 cm3 [0,12 in3]

max) with supply
voltage
Continuous actuations 1 l/min
with supply voltage
[0.26 US gal/min]
Oil viscosity *
Oil temperature
recommended range
12 - 75 mm2/s
[65 - 347 SUS]
minimum
4 mm2/s
[39 SUS]
maximum
460 mm2/s
[2128 SUS]
recommended range
30 - 60C
[86 -140F]
minimum
-30C
[-22F]
90C
[194F]
Ambient temperature recommended range
maximum
-30 60C
[-22 140F]
Filtering in the hydraulic system
Max. allowed degree of contamination: 23/19/16

(ISO 4406, 1999 version)
* Max. start up viscosity 2500 mm2/s.

PVPX technical data
Max. operating pressure
350 bar [5075 psi]
Enclosure to IEC 529
IP65
Max. pressure drop at an oil flow of 0.1 l/min [2.6 US gal/min]
2 bar [30 psi]
Oil temperature
(Inlet)
Recommended temperature
30C to 60C [86F to 140F]
Min. temperature
-30C [-22F]
Max. temperature
90C [194F]
Max. coil surface temperature
155C [311F]
Ambient temperature
-30C to 60C [-22F to 140F]
Oil viscosity
Operating range
12 to 75 mm2/s [65 to 347 SUS]
Min. viscosity
4 mm2/s [39 SUS]
Max. viscosity
460 mm2/s [2128 SUS]
Response time for LS pressure relief
300 ms
Rated voltage
12 V
Max. premissible deviation from rated supply voltage
10%
Current consumption at rated voltage at 22C [72F] coil temperature
1.55 A
0.78 A
0.5 A
Power consumption
at 110C [230F] coil temperature
1A
19 W
12 W
520L0344 Rev HE Feb 2014
24 V
31
Electrical control of PVG
Valve actuation with electrical actuators has been supported by Danfoss for a long time. The actuation
can be controlled directly by joystick, by a PLUS+1 controller or by a broad range of third part
controllers. The actuator controls the spool by building up pilot oil pressure on the end of the spool. For
the PVE a pilot oil pressure between 10 and 15 bar is used. For the PVHC a pilot oil pressure between 20
and 25 bar is used.
PVG with PVE
Valve section with naming - standard mounted - seen from PVP

P -> A
Pilot oil supply
Oil
B port
PVE
A port
PVB
PVM
Electronics
Neutral spring
NC Solenoid valves
NO solenoid valves
LVDT
PVBS
V310072.B
A detailed description of the variants is presented in:

PVE-Series 4 for PVG 32, PVG 100 and PVG 120 Technical Information, 520L0553, covers all analogue PVE
PVEO, PVEH, PVES, PVEA, PVEM, PVEU, PVEP and the current controlled PVHC.
Electrohydraulic Actuator PVED-CC Series 4 Technical Information, 520L0665, covers the ISOBUS/SAE
J1939 CAN controlled PVED-CC.
Electrohydraulic Actuator PVED-CX Series 4 Technical Information, 11070179, covers the IEC61508 SIL2
certified CANopen controlled PVED-CX.
32
520L0344 Rev HE Feb 2014
PVE characteristic - control by voltage
PVEP
control range
2.5V
5V
7.5V
PVEU
fixed
Closed loop control

The PVE variants PVEA/H/M/S/U/P and the PVED-CC/-CX has a closed loop control supported by a spool
position sensor that ensures integrity towards flow forces and oil viscosity.
Hysteresis for PVE variants*
Spool position
Hysteresis (Control signal /spool travel) is indicated at rated voltage and f = 0.02 Hz for one cycle (one
cycle = neutral full A full B neutral).
The values are typical test data for exact ranges, see PVE Technical Information, 520L0553.
520L0344 Rev HE Feb 2014
33
PVEU is available with PVEH and PVES hysteresis

PVEP, PVED-CC and PVED-CX are available with PVES hysteresis
The standard PVEs are proportional activated actuator except PVEO which is on/off.
The PVEs have fault-monitoring.
Fault monitoring overview
Type
Fault
monitoring
Delay before error

out
Error mode
Error output Fault output

status
on PVE 1)
LED light
Memory
(reset
needed)
PVEO
PVEM
No fault
monitoring
PVEA
PVEH
PVEP
PVES
PVEU
Active
500 ms
(PVEA: 750 ms)
No fault
Low
<2V
Green
Input signal faults
High
UDC
Flashing red
Yes
Transducer (LVDT)
Constant red
Close loop fault

Passive
250 ms
(PVEA: 750 ms)
No fault
Low
<2V
Green
Input signal faults
High
~UDC
Flashing red
No
Transducer (LVDT)
Constant red
Close loop fault

PVE
Float
six pin
Active
500 ms
Float not active
750 ms
Float still active
High
~UD
Constant red
1) Measured between fault output pin and ground.

PVEO
The PVEO is an on/off activated actuator. The PVEO has not fault-monitoring.
Variants:
Power supply:
PVEO-R with a ramp delayed actuation

PVEO-DI with direction indication feedback
Anodized aluminum block
ATEX certified
AMP version
12 V
24 V
Connectors:
AMP
DIN/Hirshmann
Deutsch
DIN/Hirschmann version
Deutsch version
PVEO/PVEO-R
U DC
U DC
157-502.11
34
520L0344 Rev HE Feb 2014
Yes
PVEM
The PVEM is a proportional activated actuator. The PVEM has not fault-monitoring.
Variants:
PVEM -R with a ramp delayed actuation

PVEM for float in B-direction and max. flow B at 4.8 mm
Power supply: 12 / 24 V
Connectors:DIN/Hirshmann
PVEA, PVEH, PVES, PVEU
Variants:
Power supply: 11 32 V
Connectors:
-F for float in B-direction

max. flow B at 4.8 mm
-F for float in A-direction
max. flow A at 5.5 mm
PVES-SP with spool position feedback
Anodized aluminum block
ATEX certified
AMP version
AMP
DIN/Hirshmann
Deutsch
DIN/Hirschmann version
Deutsch version
LED

and PVEH float A
PVEH, PVEM, PVES,

PVEH float B and PVEM float B

and PVEH float B
PVEP
The PVEP is controlled with separate PWM control
signals for A and B direction.
Deutsch version
PVES-SP
The PVEP has hysteresis and fault monitoring like

the PVES.
Power supply: 11 32 V
Connector: Deutsch
LED
Not
connected
Error
Us
Spool position
3
2
1
4
5
6
UDC
PVED-CC and PVED-CX

The CAN controlled PVE embedded microcontrollers support the same high spool controllability as the
PVES and additional has high quality feedbacks, safety monitoring and detailed diagnostics.
520L0344 Rev HE Feb 2014
35
PVED has digital communication, that allows a wide range of feedback, setpoint and highly costumized
settings. CAN bus serial communication makes wiring much easier. Only one cable per PVG group.
Power supply: 11 32 V PVE with Deutsch connector incl. female connector
Connectors:
Deutsch (PVED-CC)
AMP (PVED-CC and
PVED-CX)
For more information on PVED please see the PVED-CC, Series 4 Technical Information, 520L0665.
PVHC
For PVG controlled by PVHC, hysteresis is influenced by lever (PVM). The PVHC control is done by dual
Pulse Width Modulated (PVM) high current supply 100-400 Hz PWM control signals.
The PVHC does not have neither fault monitoring nor internal closed loop control of the spool.
Power supply:
12 V
24 V
PVHC with AMP version

5.7
[0.224]
44.4 [1.748]
PVHC with Deutsch version

5.7
[0.224]
5.7
[0.224]
Deutsch
AMP
26.75
[1.053]
26.75
[1.053]
74.0
[2.913]
74.0
[2.913]
16.5
[0.650]
5.75
[0.226]
P301 123
520L0344 Rev HE Feb 2014
92.25
[3.631]
92.25
[3.631]
16.5
[0.650]
36
5.7
[0.224]
33.0 [1.299]
33.0 [1.299]
Connectors:
44.4 [1.748]
5.75
[0.226]
P301 124
PVHC characteristic - Spool stroke vs current
Spool stroke, mm
7
6
5
Ideal curve
4
3
Hysteresis
500/1000 mA
280/560 mA
280/560 mA
500/1000 mA
1600
@ 12V
800
1400
700
1200
600
1000
Current in mA
500
800
400
600
300
400
200
200
100
200
100
400
200
600
300
800
400
1000
500
1200
600
1400
700
800
1600
@ 24V
V310 000.A
PVHC current response and hysteresis @ 25 bar Pp, 21 ctS, 25 C. The ideal curve is determined by the
main spool neutral spring. The PVHC has high hysteresis. The hysteresis is affected by viscosity, friction,
flow forces, dither frequency and modulation frequency. The spool position will shift when conditions are
changed e.g. temperature change.
520L0344 Rev HE Feb 2014
37
General
The characteristics in this catalog are typical measured values. During measuring a mineral based
hydraulic oil with a viscosity of 21 mm2/s [102 SUS] at a temperature of 50C [122F] was used.
PVP, pump side module
Pressure relief valve characteristic in PVP
The pressure relief valve is set at an oil flow of 15 l/min [4.0 US gal/min].
Setting range:
30 to 350 bar [435 to 5075 psi] with PVSI end plate

30 to 300 bar [435 to 4351 psi] with PVS end plate
Pressure relief valve characteristic
Neutral by-pass pressure drop characteristic (open

center)
PVB, basic modules oil flow characteristics

The oil flow for the individual spool depends on:
38
type of basic module (with/without compensation)

type of pump (fixed or variable displacement).
520L0344 Rev HE Feb 2014
Linear oil flow depending on spool type
US = Signal voltage; UDC = Supply voltage; 1 = First PVB after PVP; 8 = Eighth PVB after
Pressure-compensated PVB, open or closed center PVP
The oil flow is dependent on the supplied pump oil flow. The characteristics are plotted for a pump oil
flow, QP, corresponding to the rated max. spool oil flow, QN. Increasing the pump oil flow to 1,4 QN will
give the same oil flow on the eighth as on the first basic module.
Please note, the letters AA, A, B, etc. denote spool types. The characteristic below is shown for spool
travel in both directions. All other characteristics are shown for spool travel in one direction only.
520L0344 Rev HE Feb 2014
39
Progressive oil flow characteristic depending on spool type
PVM
PVM
PVE
PWM for PVEP/T
control range
157-61.im
US = Signal voltage; UDC = Supply voltage; 1 = First PVB after PVP; 8 = Eighth PVB after
PVB without pressure compensation, open center PVP
The spool flow is dependent on the supplied oil flow, QP.
The characteristics apply to supply oil flow of 130 l/min [34.3 US gal/min] with the actuation of one basic
module and the supply flow level.
If several basic modules are activated at the same time, the characteristic depends on the load pressure
of the actuated basic modules.
40
520L0344 Rev HE Feb 2014
Oil flow as a function of spool travel characteristic
Oil flow QA/B as a function of supplied pump oil flow (QP)

The pressure drop of any oil flowing back to tank (QP - QA/B) is read on the curve for neutral flow pressure
in PVP.
Characteristic for fully displaced flow control spools
520L0344 Rev HE Feb 2014
41
PVB without pressure compensation, closed center PVP
Set pressure difference between pump pressure and LS signal = 10 bar [145 psi].
Set pressure difference between pump pressure and LS signal = 20 bar [290 psi].
42
520L0344 Rev HE Feb 2014
The oil flow is dependent on the pressure difference between the pump pressure and the LS signal.
Normally the pressure difference is set at the LS pump regulator. Also take into consideration pressure
drop from the pump to the PVG valve group. e.g. long pipeline.
Oil flow characteristics for PVB at
@ pressure drop at max. main spool travel
@ pressure drop for open spool in neutral position
Load-independent, pressure-compensated
LS pressure limiting, pressure-compensated PVB
PVLP, shock and PVLA, suction valves

PVLP is set at an oil flow of 10 l/min [2.6 US gal/min]. The shock valve PVLP is designed to absorb shock
effects. Consequently, it should not be used as a pressure relief valve.
If the working function requires the use of a pressure relief valve, a PVB basic module with built-in LSA/B
pressure limiting valve should be used.
520L0344 Rev HE Feb 2014
43
PVLP, shock valve characteristic
Pressure build-up for pressure controlled spools

Max. oil flow can be reduced by about
50% without limitation of maximum
pressure by limiting the main spool
travel from 7 mm [0.28 in] to 5.5 mm
[0.22 in].
44
520L0344 Rev HE Feb 2014
PVLA, suction valve characteristic
Pressure control spool flow characteristics
Size A:
Size B:
Example 1
Size C:
Size D:
Example 2
Size E:
Examples of how to use the characteristics for pressure control spools

Example 1: Determining the oil flow
Example 2: Determining the spool size
Given:
Given:
520L0344 Rev HE Feb 2014
45
Example 1: Determining the oil flow
Example 2: Determining the spool size
Spool type B
Pressure setting PP: 160 bar [2320 psi]
Load pressure, LSA/B: 100 bar [1450 psi]
Max. oil flow, QA/B: 90 l/min [23.8 US gal/min]

Pressure setting PP: 150 bar [2175 psi]
Load pressure, PLSA: 125 bar [1810 psi]
Result:
Result:
Oil flow = 75 l/min [19.8 US gal/min]
D spool (see Pressure control spool flow

characteristics, size D)
Normally a smaller spool can be chosen with pressure control. It is our experience that the spool can be
one size smaller than with normal flow control.
Characteristics for float position main spools
Characteristic of oil flow, spool travel and voltage
8 mm [0.19 in] spool displacement in direction A gives max. oil flow to port A
8 mm [0.19 in] spool displacement in direction B gives max. oil flow to port B
8 mm [0.32 in] spool displacement in direction B gives completely open float position A/B T.
The spools have 4,8 mm spool travel in direction A and 8 mm travel in direction B:
For more information regarding electrical actuation of float spools please see PVE series 4 Technical
Information, 520L0553.
46
520L0344 Rev HE Feb 2014
Pressure drop A/B T at max. spool travel within the proportional range (4.8 mm) [0.19 in]
Spools D and E have the same opening area for forward flow and return flow.
Spool E can give 100 l/min [26.4 US gal/min] pressure compensated oil flow due to a higher pressure
drop across spool E. This occurs during spool actuation only.
Pressure drop A/B T in float position
520L0344 Rev HE Feb 2014
47
Hydraulic systems
Manually actuated PVG 32 fixed displ. pump
Example schematic of manually actuated PVG 32 fixed displacement pump
48
520L0344 Rev HE Feb 2014
Hydraulic systems
Electrically actuated PVG 32 variable displ. pump
Example schematic of electrically actuated PVG 32 variable displacement pump (electrical actuator, shock valves, relief valve)
520L0344 Rev HE Feb 2014
49

Oil
The main duty of the oil in a hydraulic system is to transfer energy. It must also lubricate the moving parts
in hydraulic components, protect them against corrosion, and transport dirt particles and heat out of the
system. It is therefore important to choose the correct oil with the correct additives. This gives normal
operation and long working life.
Mineral oil
For systems with PVG 32 valves Danfoss recommends the use of mineral-based hydraulic oil containing
additives: Type HLP (DIN 51524) or HM (ISO 6743/4).
Non-flammable fluids
Phosphate-esters (HFDR fluids) can be used without special precautions. However, dynamic seals must be
replaced with FPM (Viton) seals. Please contact the Danfoss Sales Organization if the PVG 32 valve is to be
used with phosphate-esters.
The following fluids should only be used according to agreement with the Danfoss Sales Organization
for:
Water-glycol mixtures (HFC fluids)

Water-oil emulsions (HFB fluids)
Oil-water emulsions (HFAE fluids)
Particle content, degree of contamination

Biodegradable oils
PVG 32 valves can be used in systems with rapeseed oil. The use of rapeseed oil is conditioned by:
complying with the demands on viscosity, water content, temperature and filtering etc. (see chapters
below and technical data).
adapting the operating conditions to the directions of the oil supplier.
Before using other biodegradable fluids, please consult the Danfoss organization. Oil filtration must
prevent particle content from exceeding an acceptable level, i.e., an acceptable degree of contamination.
Maximum contamination for PVG 32 is 23/19/16 (see ISO 4406. Calibration in accordance with the ACFTD
method). In our experience a degree of contamination of 23/19/16 can be maintained by using a filter
fineness as described in the next section.
For more information, please see the Danfoss literature:
Design Guidelines for Hydraulic Fluid Cleanliness Technical Information, 520L0467

Hydraulic Fluids and Lubricants Technical Information, 521L0463
Experience with Biodegradable Hydraulic Fluids Technical Information, 521L0465.
Filtration
Effective filtration is the most important precondition in ensuring that a hydraulic system performs
reliably and has a long working life. Filter manufacturers issue instructions and recommendations. It is
advisable to follow these.
System filters
Where demands on safety and reliability are very high a pressure filter with bypass and indicator is
recommended. Experience shows that a 10 m nominal filter (or finer) or a 20 m absolute filter (or finer)
is suitable. It is our experience that a return filter is adequate in a purely mechanically operated valve
50
520L0344 Rev HE Feb 2014

system. The fineness of a pressure filter must be selected as described by the filter manufacturer so that a
particle level of 23/19/16 is not exceeded. The filter must be fitted with pressure gauge or dirt indicator to
make it possible to check the condition of the filter. In systems with differential cylinders or accumulators
the return filter must be sized to suit the max. return oil flow. Pressure filters must be fitted to suit max.
pump oil flow.
Internal filters
The filters built into PVG 32 are not intended to filter the system but to protect important components
against large particles. Such particles can appear in the system as a result of pump damage, hose fracture,
use of quick-couplings, filter damage, starting up, contamination, etc. The filter in the electrical actuator
PVE protecting the solenoid valves has a mesh of 150 m. Bursting pressure drop for internal filters is 25
bar [360 psi].
520L0344 Rev HE Feb 2014
51
Dimensions
PVG 32 Dimensions
F: Shock and suction valve, PVLP

G: Pressure gauge connection: G, 12 mm [9/16-18, 0.5 in] deep
H: Plug for external pilot oil supply, PVPC: G, 12 mm [ 20, 0.47 in] deep
I: Electrical LS unloading valve, PVPX
J: LS connection: G, 12 mm [20; 0.47 in or 9/16-18, 0.5 in] deep
K: Fixing holes: M8 min. 10 [5/1618; 0.39 in] deep
L: Port A and B: G, 14 mm [7/8 14; 0.65 in] deep
M: LX connection: PVS; G 1/8, 10 mm [3/8 24; 0.39 in] deep and PVSI; G, 12 mm [ -20; 0.47 in] deep
52
520L0344 Rev HE Feb 2014
Dimensions
N: LS pressure limiting valve
O: Tank connection; G, 16 mm [1 1/16-12; 0.75 in] deep
P: Pressure relief valve
Q: Pump connection; G, 14 mm [7/8-14; 0.65 in] deep or G, 16 mm [1 1/16-12; 0.75 in] deep
R: LSA and LSB connections; G, 12 mm deep [9/16-18, 0.5 in] deep
S : Pp, pilot pressure connection G
PVB
L1
L2
10
11
12
mm
82
130
178
226
274
322
370
418
466
514
562
610
[in]
[3.23]
[5.12]
[7.01]
[8.90]
[10.79]
[12.68]
[14.57]
[16.46]
[18.35]
[20.24]
[562]
[610]
mm
140
189
238
287
336
385
434
483
527
576
622
670
in]
[5.51]
[7.44]
[9.37]
[11.30]
[13.23]
[15.16]
[17.09]
[19.02]
[20.95]
[22.87]
[622]
[670]
520L0344 Rev HE Feb 2014
53
Dimensions
44 [
110[4.33]
max.200.5[7.894]
6.5
1.73
85[3.35]
33[1.30]
P
V
M
D
~1
65[
2]
6.5[0.256]
7[0.28]
49.5[1.949]
P
V
H
7[0.28]
32[1.26]
85[3.35]
58.5[2.303]
45[1.77]
P
V
M
R
/
F
0]
A-A
60[2.36]
17[0.67]
7[0.28]
129[5.08]
95[3.74]
13[0.51]
85.5[3.366]
B-B
PVEO
107[4.21]
110[4.33]
max.290.50[11.437]
60[2.36]
89.5[3.524]
117[4.61]
7[0.28]
139[5.472]
C-C
PVEM/PVEH/
PVES
107[4.21]
110[4.33]
max.290.50[11.437]
60[2.36]
V310141.A
F : G 1/4, 12 mm deep [1/2 in - 20, 0.47 in deep]
54
520L0344 Rev HE Feb 2014
Dimensions
PVM, control lever positions
Base with an angle of 37.5
Base with an angle of 22.5
19.
19.5
19
19
.5
.5
37.5
67
.5
.5
97
.5
127
22.5
52
.5
82
.5
11
172.5
187.5
142.5
2.5
157.5
V310018.A
V310014.A
The angle of the handle is determined by which side of the handle that is mount towards the base. If a
22.5 angle is needed the "dot" on the handle is not visible. If 37.5 is needed the dot should be visible.
Surface treatment
The PVG valve has as standard, an untreated surface. In certain applications, depend on different factors,
such as: salty environment, large temperature changes, high humidity, rust can develope on the surface.
This will not affect the performance of the PVG valve group. To prevent/reduce rust development,
Danfoss recommend the PVG valve group to be painted. Rust on the surface is not seen as a valid
complaint issue, neither on painted or unpainted PVG valve groups.
520L0344 Rev HE Feb 2014
55

Symbol
Description
Open center pump side module for pumps
with fixed displacement.
For purely mechanically actuated valve
groups
Code number
P=G
T=G
157B5000
P = 7/814
T = 1 1/1612
157B5200
P, T = G
157B5100
P, T = 1 1/1612
157B5300
P=G
T=G
157B5001
P = 7/814
T = 1 1/1612
157B5201
For purely mechanically actuated valve

groups.
P, T = G
157B5101
P, T = 1 1/1612
157B5301

With pilot oil supply for electrically actuated
valves.
P=G
T=G
157B5010
P = 7/814
T = 1 1/1612
157B5210
P, T = G
157B5110
P, T = 1 1/1612
157B5310
P=G
T=G
157B5011
P = 7/814
T = 1 1/1612
157B5211
P, T = G
157B5111
P, T = 1 1/1612
157B5311
P=G
T=G
157B5012
P = 7/814
T = 1 1/1612
157B5212
P, T = G
157B5112
P, T = 1 1/1612
157B5312
P=G
T=G
157B5013
P = 7/814
T = 1 1/1612
157B5213
P, T = G
157B5113
P, T = 1 1/1612
157B5313
Closed center pump side module for pumps

with vaiable displacement.

with variable displacement.
valves.

valves
Connection for electrical LS unloading valve,
PVPX (not incl.)

with variable displacement
With pilot oil supply
Connection for electrical LS unloading valve,
PVPX (not incl.)
Connections:
P = G in; 14 mm deep or G in; 16 mm deep / LS, M = G in; 12 mm deep / T = G in; 16 mm deep.
P = 7/814; 0.65 in deep or 1 1/1612; 0.75 in deep / LS, M = 20; 0.47 in deep / T = 1 1/1612; 0.75 in
deep.
56
520L0344 Rev HE Feb 2014

Symbol
Description
Code number
Open center pump side module for pumps with fixed

displacement.
For mechanical actuated valves.
Connection for LS unloading valve, PVPX (not incl)
P, T = G
157B5102
Closed center pump side module for pumps with

vaiable displacement.
For mechanical actuated valves.
Connection for LS unloading valve, PVPX (not incl)
P, T = G
157B5103

displacement.
With pilot oil supply for electrical actuation and
connection for pilot oil pressure
Incl. check valve
P, T = G
157B5180
P, T = 1 1/1612
LS connection =
9/1618
157B5380
Closed center pump side module for pumps with

variable displacement.
With pilot oil supply for electrical actuation and
Incl. check valve
P, T = G
157B5181
P, T = 1 1/1612
LS connection =
9/1618
157B5381

displacement.
With pilot oil supply for hydraulic actuation and
P, T = G
157B5190
P, T = 1 1/1612
LS connection =
9/1618
157B5390
Closed center pump side module pumps with variable

displacement
With pilot oil supply for hydraulic actuation and
P, T = G
157B5191
P, T = 1 1/1612
LS connection =
9/1618
157B5391
Connections:
P, T = G in; 16 mm deep / LS, M = G in; 12 mm deep
P, T = 1 1/1612; 0.75 in deep / LS, M = 20; 0.47 in deep.
520L0344 Rev HE Feb 2014
57

PVB, basic modules
PVB, basic modules without adjustable LSA/B pressure limiting valves
Symbol
Description
No facilities for
shock valves A/B
Facilities for shock

valves A/B
Without load drop check valve and

pressure compensator.
Can be used where load holding
valves prevent oil from flowing
back through channel P.
G
14 mm deep
157B6000
157B6030
7/814
0.65 in deep
157B6400
157B6430
Load drop check valve.
G
14 mm deep
157B6100
157B6130
7/814
0.65 in deep
157B6500
157B6530
Load drop check valve.

LSA/B shuttle valve.
To be used with float position
spools.
G
14 mm deep
157B6136
7/814
0.65 in deep
157B6536
Non-damped compensator valve
G
14 mm deep
157B6200
157B6230
7/814
0.65 in deep
157B6600
157B6630
G
14 mm deep
11071832
7/814
0.65 in deep
Without compensator valve

LSA/B shuttle valve
V310411.A
58
Code number
520L0344 Rev HE Feb 2014
PVB, basic modules without adjustable LSA/B pressure limiting valves (continued)
Symbol
Description
Code number
With damped compensator valve
No facilities for
shock valves A/B
Facilities for shock

valves A/B
G
14 mm deep
157B6206
157B6236
7/814
0.65 in deep
11036629
11036630
PVB, basic modules with adjustable LSA/B pressure limiting valves

Symbol
Description
Code number
No facilities for
shock valves A/B
Facilities for
shock valves A/B
With non-damped
compensator valve
Adjustable LSA/B pressure
limiting valves
External LS connection port
A/B.
Also used for float position
spools
G
14 mm
deep
157B6203
157B6233
7/814
0.65 in
deep
157B6603
157B6633
Damped compensator valve

Adjustable LSA/B pressure
limiting valves
External LS connection port
A/B
G
14 mm
deep
157B6208
157B6238
7/814
0.65 in
deep
11036631
PVLP, shock and suction valve (fitted in PVB)

PVLP, shock/ and anti-cavitation valves
Code no.
157B....
Settings
2032
2050
2063
2080
2100
2125
2140
2150
2160
2175
2190
bar
32
50
63
80
100
125
140
150
160
175
190
psi
460
725
914
1160
1450
1813
2031
2175
2320
2538
2755
520L0344 Rev HE Feb 2014
59
PVLP, shock and suction valve

Symbol
Description
Shock and suction valve for port A and/or B.
(Not adjustable).
Lifetime 200.000 actuations.
PVLA, suction valve (fitted in PVB)

PVLA, suction valve
Symbol
Description
Code
number
Suction valve for port A and/or B.
157B2001
Plug for connecting the nonactive port to

tank, when using a single acting spool.
157B2002

Symbol
60
Description
Code number
with stop screws w/o stop screws
PVM, Standard, spring centered

Individual oil flow adjustment to ports A and B
157B3171
157B3191
Without actuation lever and base.

Shaft for mounting of actuation lever
157B3173
157B3193
PVM, as standard, witout actuation lever.

With base for mounting of actuation lever
157B3174
157B3194
PVM, Standard, spring. Individual oil flow

adjustment to ports A and B. (Anodized)
157B3184
520L0344 Rev HE Feb 2014
PVMD, cover for mechanical actuation

Symbol
Description
Material
Code No.
Anodized
PVMD, Cover for purely mechanically operated valve
aluminium
157B0001
no
aluminium
157B0009
yes
cast iron
157B0021
no
Description
Material
Code number
Anodized
PVMR, Friction detent
aluminium
157B0004
no
aluminium
157B0012
yes
cast iron
157B0024
Description
Material
Code number
Anodized
PVMF,
Mechanical float position lock
aluminium
157B0005
no
Description
Material
Code number
Anodized
PVH, Cover for Hydraulic actuation

PVH 9/16-18 UNF
aluminium
157B0007
no
aluminium
157B0010
yes
cast iron
157B0014
no
aluminium
157B0008
no
aluminium
157B0011
yes
cast iron
157B0016
no

Symbol
PVMF, mechanical float position

Symbol

Symbol
PVH, Cover for Hydraulic actuation

PVH G1/4
PVS, end plate

PVS, end plate
Symbol
Description
Mounting
threads
Code number
PVS, without active elements.

No connections
BSP
157B2000
SAE
157B2020
G 1/8 10 mm deep
BSP
157B2011
3/8 in - 24; 0,39 in deep
SAE
157B2021
V310062.A
LX
V310063.A
PVS, without active elements.

Max. intermittend LX pressure
250 bar [3625 psi]
520L0344 Rev HE Feb 2014
61
PVS, end plate (continued)

Symbol
Description
Mounting
threads
Code number
PVSI, without active elements

Without connections.
BSP
157B2014
SAE
157B2004
G 1/4 10 mm deep
BSP
157B2015
1/2 in - 20; 0,47 in deep
SAE
157B2005
V310062.A
LX
PVSI, without active elements

LX connections.
Max. intermittend LX pressure:
350 bar [5075 psi]
V310063.A
For mounting threats please see the chapter Dimensions.

PVAS, assembly kit
PVAS, assembly kit
Code no,
157B...
10
11
12
PVBs
8000
8001
8002
8003
8004
8005
8006
8007
8008
8009
8010
8061
8062
PVB + PVPVM -
8021
8022
8023
8024
8025
8026
8027
8028
8029
8030
8081
8082
Weight kg [lb] 0.1[0.2]
0.15
[0.3]
0.25
[0.6]
0.30
[0.7]
0.40
[0.9]
0.45
[1.0]
0.50
[1.1]
0.60
[1.3]
0.65
[1.4]
0.70
[1.6]
0.80
[1.7]
0.85
[1.8]
0.9 [2.0]
PVPX, electrical LS unloaded valve

PVPX, electrical LS unloaded valve
Symbol
Description
Code number
PVPX, Normally open:

LS pressure relieved with no signal to PVPX
12 V
157B4236
24 V
157B4238
PVPX, Normally closed:

12 V
157B4246
24 V
157B4248
PVPX, Normally open with manual override:

Manual override DE-selects LS-pump
12 V
157B4256
24 V
157B4258
Plug
157B5601
PVPC, plug for external pilot oil supply

PVPC, plug for external pilot oil supply
Symbol
Description
PVP,
Plug without check valve for open
or closed center
62
520L0344 Rev HE Feb 2014
Code number
G 1/2,
12 mm deep
157B5400
1/2 in - 20;
0.47 in deep
PVPC, plug for external pilot oil supply (continued)

Symbol
Description
PVP,
Plug with check valve for
open center
520L0344 Rev HE Feb 2014
Code number
G 1/2,
12 mm deep
157B5600
1/2 in - 20;
0.47 in deep
157B5700
63

Standard FC spools
PVB is with LSA/B shuttle valve
Code number 157B....
PVB is without LSA/B shuttle valve
Press. compensated flow: l/min [US gal/min]
ISO symbol
Press. compensated flow l/min [US gal/min]
Symbol
F
E
D
C
B
130
100
65
40
25
[34.3] [26.4] [17.2] [10.6] [6.6]
A
10
[2.6]
AA
5 [1.3]
AA
A
5 [1.3] 10
[2.6]
B
25
[6.6]
C
D
E
F
40
65
100
130
[10.6] [17.2] [26.4] [34.3]
7026
7020
7025
7005
7000
7001
7002
7003
7004
7006
7105
7100
7101
7102
7103
7104
7106
7200
7201
7202
7203
7204
7301
7302
7303
7304
7401
7402
7403
7404
7406
7501
7502
7503
7504
7024
7023
7022
7021
4-way, 3-position
Closed neutral position
7126
7124
7123
7122
7121
7120
7125
4-way, 3-position
Throttled, open neutral position
-
3-way, 3-position
Closed neutral position, P A
-
3-way, 3-position
Closed neutral position, P B
-
7424
7423
7422
7421
4-way, 3-position
Throttled, A T in neutral position
-
7524
7523
7522
7521
4-way, 3-position
Throttled, B T in neutral position
-
7624
7623
7622
7621
7620
157-139.10
157-140.10
4-way, 4-position
Float P B F
64
520L0344 Rev HE Feb 2014

Standard FC spools, hydraulic actuation
ISO symbol

Symbol
E
100
[26.4]
D
65
[17.2]
C
40
[10.6]
B
25
[6.6]
A
10
[2.6]
AA
5
[1.3]
AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
40
[10.6]
D
65
[17.2]
E
100
[26.4]
9024
9023
9022
9021
9020
9025
9005
9000
9001
9002
9003
9004
9105
9100
9101
9102
9103
9104
4-way, 3-position
closed neutral position
9124
9123
9122
9121
9120
9125
4-way, 3-position
Throttled open neutral position
FC spools for mechanical float position, PVMF

ISO symbol
Press. compensated flow l/min [US gal/min]
Symbol
F
E
D
C
B
130
100
65
40
25
[34.3] [26.4] [17.2] [10.6] [6.6]
A
10
[2.6]
AA
5
[1.3]
AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
D
E
F
40
65
100
130
[10.6] [17.2] [26.4] [34.3]
9820
9825
9824
9823
9822
9821
4-way, 4 position
PAF
-
9624
623
9622
9621
157-140.10
157-139.10
4-way, 4-position
Float P B F
FC spools for friction detent, PVMR


E
100
[26.4]
D
65
[17.2]
C
40
[10.6]
B
25
[6.6]
A
10
[2.6]
ISO symbol
AA
5
[1.3]
520L0344 Rev HE Feb 2014

Symbol

AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
40
[10.6]
D
65
[17.2]
E
100
[26.4]
65

9724
9723
9722
9721

9720
9700
9701
9702
9703
9704
9710
9711
9712
9713
9714
4-way, 3-position
closed neutral position
9734
9733
9732
9731
9730
4-way, 3-position
Throttled open neutral position
FC spools with linear flow characteristic

ISO symbol
Symbol
F
E
D
C
B
130
100
65
40
25
[34.3] [26.4] [17.2] [10.6] [6.6]
A
10
[2.6]
AA
5
[1.3]
AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
D
E
F
40
65
100
130
[10.6] [17.2] [26.4] [34.3]
9750
9751
9752
9753
9754
9760
9761
9762
9763
9764
9794
9804
9774
9773
9772
9771
4-way, 3-position
-
9784
9783
9782
9781
4-way, 3-position
Throttled, open neutral position
-
4-way, 3-position
Throttled, A T in neutral position
-
4-way, 3-position
B T in neutral position
66
520L0344 Rev HE Feb 2014

Standard PC spools
ISO symbol

Symbol
E
100
[26.4]
D
65
[17.2]
C
40
[10.6]
B
25
[6.6]
A
10
[2.6]
AA
5
[1.3]
AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
40
[10.6]
D
65
[17.2]
E
100
[26.4]
7033
7032
7031
7030
7035
7015
7010
7011
7012
7013
7115
7110
7111
7112
7113
7040
7041
7042
7043
7044
7050
7051
7052
7053
7054
7150
7151
7152
7153
7154
7150
7151
7152
7153
7154
7452
7453
4-way, 3-position
Closed neutral position, PC A and B
7134
7133
7132
7131
7130
7135
4-way, 3-position Throttled, open neutral position,

PC A and B
7064
7063
7062
7061
4-way, 3-position
Closed neutral position, PC A
7074
7073
7072
7071
4-way, 3-position
Closed neutral position, PC B
7164
7163
7162
7161
4-way, 3-position
Throttled, open neutral position, PC A
7174
7173
7172
7171
4-way, 3-position
Throttled, open neutral position, PC B
-
7473
7472
7471
7470
4-way, 3-position
Throttled, A T neutral position, PC B
520L0344 Rev HE Feb 2014
67

-
7563
7562

-
7541
7542
7543
4-way, 3-position
Throttled, B T neutral position , PC A
Standard PC spools, hydraulic actuation

ISO symbol

Symbol
E
100
[26.4]
D
65
[17.2]
C
40
[10.6]
B
25
[6.6]
A
10
[2.6]
AA
5
[1.3]
AA
5
[1.3]
A
10
[2.6]
B
25
[6.6]
C
40
[10.6]
D
65
[17.2]
E
100
[26.4]
9015
9010
9011
9012
9042
9043
9044
9052
9053
9054
4-way, 3-position
Closed neutral position, PC A and B
-
4-way, 3-position
Closed neutral position, PC A
-
4-way, 3-position
Closed neutral position, PC B
68
520L0344 Rev HE Feb 2014

PVB, basic valves
0
0
1-13
16
14
a
15
V310168.A
PVB, basic valves

Description
No facilities for shock valves A and B
Facilities for shock valves A and B
78 - 14 UNF
78 - 14 UNF
Without compensator /check valve
157B6000
157B6400
157B6030
157B6430
With check valve
157B6100
157B6500
157B6130
157B6530
With check valve and LSA/B shuttle valve
157B6136
157B6536
With compensator valve
157B6200
157B6600
157B6230
157B6630
520L0344 Rev HE Feb 2014
69
PVB, basic valves (continued)

Description
No facilities for shock valves A and B
Facilities for shock valves A and B
78 - 14 UNF
78 - 14 UNF
With damped compensator valve
157B6206
157B6236
With compensator valve, LSA/B relief valve and LSA/B shuttle

valve
157B6203
157B6603
157B6233
157B6633
With damped compensator valve,

LSA/B relief valve and LSA/B shuttle valve
157B6208
157B6238
Weight
3.1 [6.8]
kg [lb]
3.0 [6.6]
PVPC, plugs
Description
in - 20
Weight
kg
[lb]
External pilot supply
157B5400
0.05
0.1
External pilot supply incl. check valve
157B5600
157B5700
0.05
0.1

Description
Alu
Alu anodized
Cast iron
Angle
with stop screws
without stop
screws
with stop screws
with stop screws
157B3171
157B3191
157B3184
157B3161
22,5/37,5
Standard with base, without arm and button 157B3174
157B3194
22,5/37,5
Standard without base, without arm and

button
157B3173
157B3193
157B3186
Weight kg [lb]
0.4 [0.9]
Standard
0.8 [1.8]
PVAS, assembly kit

Code no. 0
157B....
10
11
12
PVBs
8000
8001
8002
8003
8004
8005
8006
8007
8008
8009
8010
8061
8062
PVB +
PVPVM
8021
8022
8023
8024
8025
8026
17B8027 8028
8029
8030
8081
8082
Weight
kg [lb]
0.1 [0.2]
0.15 [0.3] 0.25 [0.6] 0.30 [0.7] 0.40 [0.9] 0.45 [1.0] 0.50 [1.1] 0.60 [1.3] 0.65 [1.4] 0.70 [1.6] 0.80 [1.7] 0.85 [1.8] 0.9 [2.0]

Description
Open
center
70
Without pilot supply
With pilot supply
for PVE
for PVE with

for PVE
facilit. for PVPX
for PVE and

facilit. for
PVPX
for PVE and pilot

oil pressure takeoff
for PVH and pilot

P = G1/2, T = G3/4
157B5000
157B5010
157B5012
P = 7/8 -14, T = 11/16 -12
157B5200
157B5210
157B5212
520L0344 Rev HE Feb 2014
PVP, pump side module (continued)

Description
Without pilot supply

for PVE
for PVE with

for PVE
facilit. for PVPX
for PVE and

facilit. for
PVPX
for PVE and pilot

for PVH and pilot

157B5100
157B5102
157B5110
157B5112
157B5180
157B5190
P = 1 1/16 -12, T = 11/16 -12 157B5300
157B5310
157B5312
157B5380
157B5390
P = G1/2 , T = G3/4,
157B5001
157B5011
157B5013
P = 7/8 -14, T = 11/16 -12
157B5201
157B5211
157B5213
P = G3/4, T = G3/4,
157B5101
157B5103
157B5111
157B5113
157B5181
157B5191
157B5311
157B5313
157B5381
157B5391
P = G3/4, T = G3/4
Closed
center
P = 11/16 -12, T = 1 1/16 -12 157B5301

Weight
With pilot supply
kg [lb]
3 [6.6]
PVPX, electrical LS pressure relief valves

Description/
Supply voltage
Normally open
Normally closed
Normally open with manual override
Code No. Hirsch.
Code No.
AMP
Weight
kg [lb]
12 V
157B4236
157B4981
0.3 [0.7]
24 V
157B4238
157B4982
12 V
157B4246
157B4983
24 V
157B4248
157B4984
12 V
157B4256
157B4985
24 V
157B4258
157B4986
Plug
157B5601
0.06 [.13]
PVS and PVSI, end plate

Description
BSP
SAE
Weight
kg [lb]
PVS, without connections
157B2000
157B2020
0.5 [1.1]
PVS, with LX connection

G 1/8 [3/8 -24 UNF]
157B2011
157B2021
PVSI, without connections
157B2014
157B2004
PVSI, with LX connections

G 1/4 [1/2 -20 UNF]
157B2015
157B2005
1.7 [3.6]
PVLP, shock/ and anti-cavitation valves

Code no.
Settings
157B203
2
157B205
0
157B206
3
157B208
0
157B210
0
157B212
5
157B214
0
157B215
0
157B216
0
157B217
5
157B219
0
bar
32
50
63
80
100
125
140
150
160
175
190
psi
460
725
914
1160
1450
1813
2031
2175
2320
2538
2755
157B221
0
157B223
0
157B224
0
157B225
0
157B226
5
157B228
0
157B230
0
157B232
0
157B235
0
157B238
0
157B240
0
bar
210
230
240
250
265
280
300
320
350
380
400
psi
3045
3335
3480
3625
3845
4061
4351
4641
5075
5511
5801
Code no.
Settings
520L0344 Rev HE Feb 2014
71

PVE, electrical actuation
PVE, electrical actuation
Description
Code No.
Hirsch
AMP
Deut.
12 V
157B4216
157B4901
157B4291
24 V
157B4228
157B4902
157B4292
12 V
157B4217
157B4903
24 V
157B4229
157B4904
PVEM, prop. medium

Standard
12 V
157B4116
24 V
157B4128
PVEM, prop. medium Float

>B
12 V
157B4416
24 V
157B4428
PVEA, active fault mon.

PVEA, passive fault mon.
157B4734
157B4735
157B4792
-
PVEA-DI, active fault mon.

PVEA-DI, passive fault mon.
157B4736
157B4737
157B4796
-
PVEH active fault mon.

PVEH passive fault mon.
157B4032
157B4033
157B4034
157B4035
157B4092
157B4093
PVEH float > B, act. fault

PVEH float > A, act. fault
157B4332
-
157B4338
157B4392
-
PVEH- DI active fault mon.

PVEH - DI passive fault mon.
157B4036
157B4037
157B4096
-
PVES, active fault mon.

PVES, passive fault mon.
157B4832
157B4833
157B4834
157B4835
157B4892
-
PVEO, on-off
PVEO-R, on/off
Weight
kg [lb]
0.6 [1.3]
0.9 [2.0]
1.0 [2.2]
0.9 [2.0]
1.0 [2.2]
PVMD, PVMR, PVMF, PVH covers

Description
Code No.
Material
Anodized
Weight
kg [lb]
PVMD
Cover for PVB
PVMR
(Friction Detent)
157B0001
aluminium
157B0009
157B0021
cast iron
N/A
0.9 [2.0]
157B0004
aluminium
no
0.3 [0.6]
157B0012
yes
cast iron
N/A
157B0005
aluminium
no
Hydraulic actuation PVH 9/16-18 UNF 157B0007
aluminium
no
157B0010
Hydraulic actuation PVH G1/4
157B0014
cast iron
N/A
157B0008
aluminium
no
157B0016
0.2 [0.4]
yes
157B0011
520L0344 Rev HE Feb 2014
0.1 [0.2]
yes
157B0024
PVMF
(Mech. float position)
72
no
yes
cast iron
N/A
0.9 [2.0]
PVLA, anti-cavitation valve

Description
Code No.
Weight
kg
[lb]
Plug A or B
157B2002
0.04
0.09
Valve A or B
157B2001
0.05
0.1
520L0344 Rev HE Feb 2014
73
Order specification
An order form for PVG 32 hydraulic valve is shown on the next page.
The form can be obtained from the Danfoss Sales Organization.
Both the module selection chart on the previous pages and the order form are divided into fields 0,
1-1-12, 13, 14, 15, a, b, and c.
Each module has its own field:
0:
Pump side module PVP

Plug for external pilot oil supply PVPC
Electrical LS unloading valve PVPX
1-12: Basic valves PVB

13: Main spool PVBS
a: Mechanical actuator PVM (or PVE when option mounted)
c:
Cover for mechanical actuation PVMD

Cover for hydraulic actuation PVH
Electrical actuators PVE (or PVM when option mounted)
b:
Shock and suction valve PVLP

Suction valve PVLA
14: End plate PVS

15: Assembly kit PVAS
Please state
Code numbers of all modules required

Required setting (P) for pump side module
Required setting of LSA/B pressure limiting valves, see pressure setting guidance below.
Standard and option assembly

The PVG 32 valve group is assembled the way the module selection chart shows if the code number for
PVM is written in field 'a', and the code number for PVMD, PVE or PVH in field 'c'.
The valve group is assembled so that the mechanical actuator is mounted on the opposite end of the
basic module, if the code number for PVM is written in field 'c' of the order form and the code numbers
for PVMD, PVE or PVH in field 'a'.
Reordering
The space at the top right-hand corner of the form is for Danfoss to fill in. The code number for the whole
of the specified valve group (PVG No.) is entered here.
In the event of a repeat order all you have to do is enter the number Danfoss has given on the initial
confirmation of order.
Pressure setting limits
The maximum setting pressure for the pressure limiting valves LSA or LSB depends on the chosen
pressure setting for shock valve PVLP. The maximum values recommended to avoid interaction can be
read in the following table.
74
520L0344 Rev HE Feb 2014
Order specification
The figures in the table have been calculated according to the following expressions:
PVLP 150 bar: LSA/B 0.8 PPVLP

PVLP >150 bar: PPVLP - LSA/B 30 bar.
Max. pressure setting of LSA and LSB valves relative to PVLP shock valve
Pressure
setting
for PVLP
bar 32
50
63
80
100
125
140
150
160
175
190
210
230
240
250
265
280
300
320
350
380
400
psi
72
5
91
4
11
60
145
0
181
3
203
1
217
5
232
0
283
8
275
5
304
5
333
5
348
0
362
5
384
3
406
1
435
1
464
1
507
5
551
1
580
1
40
50
64
80
100
112
120
130
145
160
180
200
210
220
235
250
270
290
320
350
370
58
0
72
0
93
0
116
0
145
0
162
5
174
0
188
5
210
0
232
0
261
0
290
0
304
5
319
0
340
8
362
5
391
5
420
5
464
1
507
5
536
6
46
0
Max. for LSA/B bar psi
Min. for LSA/B
30 bar [435 psi]
520L0344 Rev HE Feb 2014
75
Order specification
PVG 32 order specification form
Separate specification pads are available under the literature no. 520L0515.
76
520L0344 Rev HE Feb 2014
520L0344 Rev HE Feb 2014
77
78
520L0344 Rev HE Feb 2014
520L0344 Rev HE Feb 2014
79
Products we oer:
Bent Axis Motors

Closed Circuit Axial Piston
Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electronic components. We specialize in providing state-of-the-art technology and solutions that
excel in the harsh operating conditions of the mobile o-highway market. Building on our extensive
applications expertise, we work closely with our customers to ensure exceptional performance for a
broad range of o-highway vehicles.
Displays
Electrohydraulic Power
We help OEMs around the world speed up system development, reduce costs and bring vehicles to
market faster.
Danfoss Your Strongest Partner in Mobile Hydraulics.
Pumps and Motors
Steering
Electrohydraulics
Go to www.powersolutions.danfoss.com for further product information.
Hydraulic Power Steering
Wherever o-highway vehicles are at work, so is Danfoss.
Integrated Systems
We oer expert worldwide support for our customers, ensuring the best possible solutions for
outstanding performance. And with an extensive network of Global Service Partners, we also provide
comprehensive global service for all of our components.
Joysticks and Control

Handles
Microcontrollers and
Please contact the Danfoss Power Solution representative nearest you.
Software
Open Circuit Axial Piston

Pumps
Orbital Motors
PLUS+1 GUIDE
Proportional Valves
Sensors
Steering
Transit Mixer Drives
Comatrol
www.comatrol.com
Schwarzmller-Inverter
www.schwarzmuellerinverter.com
Local address:
Turolla
www.turollaocg.com
Valmova
www.valmova.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions US Company
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515 239 6000
Danfoss
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumnster, Germany
Phone: +49 4321 871 0
Danfoss
Power Solutions ApS
Nordborgvej 81
DK-6430 Nordborg, Denmark
Phone: +45 7488 2222
Danfoss
Power Solutions
(Shanghai) Co. Ltd.
Building #22, No. 1000 Jin Hai Rd
Jin Qiao, Pudong New District
Shanghai, China 201206
Phone: +86 21 3418 5200
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to
products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
520L0344 Rev HE Feb 2014
www.danfoss.com
Danfoss A/S, 2014

520l0344 Folletos

Uploaded by

Copyright:

Available Formats

520l0344 Folletos

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

520l0344 Folletos

Uploaded by

Copyright:

Available Formats

MAKING MODERN LIVING POSSIBLE

Proportional Valve Group

PVG 32 Proportional Valve Group

Spec. sheet update

Converted to Danfoss layout DITA CMS

Feb 2006 - Aug 2013

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

PVG 32 technical data

Features of PVG 32........................................................................................................................................................................... 6

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

Other operating conditions

Modules symbols, description and code numbers

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

Load-independent flow control:

Good regulation characteristics

Built-in pressure relief valve

Open center version for systems with fixed displacement pumps

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

Integrated pressure compensator in channel P

Electrical actuator (11 - 32 V ===):

PVES proportional, Super

PVMF, cover for Mechanical Float

Electrical remote control units:

PVMR, cover for Mechanical detent

Remote control units

JS1000 Ball grip

Hydraulic remote control unit: PVRHH

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

PVRH, hydraulic control unit, 155N

PVREL, electrical control unit, 155U

155N0004 155N0005 155N0002

PVRES, electrical control unit, 155B

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

1 Pressure relief valve

2 Pressure reduction valve for pilot oil supply

12 LS pressure limiting valve

3 Pressure gauge connection

13 Shock and suction valve, PVLP

4 Plug, open center

5 Orifice, closed center

6 Pressure adjustment spool

7 Plug, closed center

17 Suction valve, PVLA

18 Load drop check valve

19 Pilot oil supply for PVE

20 Max. oil flow adjustment screws for A/B ports

520L0344 Rev HE Feb 2014

PVG 32 Proportional Valve Group

Double-ac ting cylinder