Rici E1t11

Data Sheet
RICI-T1 RICI-E1
RICi-E1, RICi-T1
Fast Ethernet over E1/T1 Intelligent Converters
Connect Fast Ethernet

LANs over E1 or T1
circuits
Wire-speed packet forwarding

4 levels of QoS, based on four VLAN priority queues in accordance with 802.1p and
IP Precedence
Inband and out-of-band management access via ASCII terminal, Web browser,
Telnet, or SNMP
Plug-and-play using DHCP client
VLAN stacking and tagging, keeping Ethernet user traffic completely separate from
management data, while maintaining user VLAN settings intact
order from: Cutter Networks
RICi-E1 and RICi-T1 are intelligent

converters connecting Fast Ethernet LANs
over full or fractional E1 or T1 circuits.
They enable service providers and ISPs to
supply transparent Ethernet services,
without interfering with user traffic.
RICi-E1 and RICi-T1 are equipped with one

E1/T1 port and one 10/100BaseTx port.
Packets are forwarded from the Ethernet
network to the TDM network at wirespeed, fully utilizing the expensive TDM
circuit bandwidth.
RICi-E1 and RICi-T1 comply with RADs

unique set of EtherAccess features. This
feature set provides services and carrier
backhaul applications over low and highspeed SDH/SONET and PDH circuits, from
fractional and full E1/T1 or E3/T3 over
STM-1/STM-4 to Gigabit Ethernet.
The VLAN Priority bits (802.1p) and IP

Precedence priority schemes enable users
to define four different QoS levels,
according to the application requirements.
ph: 727-398-5252 / fax: 727-397-9610
The Access Company
www.bestdatasource.com
RICI-T1 RICI-E1
RICi-E1, RICi-T1
The Fast Ethernet bridge handles

1800-byte frames, supporting VLAN
applications and other protocols requiring
large frame sizes. In filter mode, the
bridge learns MAC addresses and filters
local traffic, and in transparent mode it
forwards any received packet.
A built-in ping utility checks IP connectivity

by pinging remote IP hosts.
VLAN stacking is used to tag direct user

and management traffic to different
VLANs, thus preserving the user LAN
settings, fully separating user traffic from
management data.
Temperature-hardened enclosures
resistant to extreme temperatures
(-22C to 70C/7.6 to 158F) are
available.
The DHCP client automatically obtains the

IP address, the IP mask and the default
gateway, minimizing installation time.
SPECIFICATIONS
The units feature fault propagation. When

a TDM link failure is detected, RICi-E1 and
RICi-T1 closes the user port.
MANAGEMENT
The device is managed inband via the Fast
Ethernet user ports or remotely via the
TDM port. The device may be accessed via
Telnet, a Web browser, or SNMP (for
RADview-Lite). Management traffic and
user Ethernet traffic transmit in the same
Ethernet flow, separated by different
VLANs. Local out-of band management is
provided via an ASCII terminal.
DIAGNOSTICS
Remote loopbacks are used for
troubleshooting on the physical layer.
A trace-route application quickly traces a

route from RICi-E1 or RICi-T1 to any other
network device.
ENVIRONMENT
E1 INTERFACE
Number of Ports
1
Compliance
G.703
G.704
Data Rate
2.048 Mbps
Line Code
HDB3, AMI
Framing
Unframed
Framed: G.732N
Max Frame Size
1800 bytes
Line Impedance
120, balanced
75, unbalanced
Providing Transparent LAN Services over Leased Lines
ph: 727-398-5252 / fax: 727-397-9610
Data Sheet
RICI-T1 RICI-E1
System Clock
Internal or loopback
Diagnostics
Remote loopback
Connector
RJ-45
T1 INTERFACE
Number of Ports
1
Compliance
ANSI T1.403
Data Rate
1.544 Mbps
Line Code
B8ZS, AMI
Framing
Unframed
Framed: D4 or ESF
Max Frame Size
1800 bytes
Line Impedance
100, balanced
System Clock
Internal or loopback
Diagnostics
Remote and FDL loopbacks
Connector
RJ-45
ph: 727-398-5252 / fax: 727-397-9610
RICI-T1 RICI-E1
RICi-E1, RICi-T1
WAN PROTOCOL
GENERAL
Type
GFP (G.8040, G.7041/Y.1303)
Indicators
PWR (green) Power status
TST (yellow) Test status
ALM (red) Alarm status
LOS (red) Loss of signal
ETH LINK (green) Ethernet link status
RAD proprietary HDLC compatible with

RAD products
Industry-standard HDLC
ETHERNET INTERFACE
Number of Learned MAC Addresses
Up to 512
Power
Wide-range power supply:
AC/DC: 100 to 240 VAC
or 48/60 VDC (40 to 72 VDC)
Type
10/100 Mbps autonegotiation, full/half
duplex
DC: 24 VDC (available only with

temperature-hardened metal enclosure)
Compliance
Conforms to the relevant sections of
IEEE 802.3 and 802.3u
Power Consumption
5W
Physical
Plastic enclosure:
Height: 43.7 mm (1.7 in)
Width: 220 mm (8.6 in)
Depth: 170 mm (6.7 in)
Weight: 0.5 kg (1.1 lb)
Metal enclosure:
Height: 43.7 mm (1.7 in)
Width: 215.5 mm (8.5 in)
Depth: 152.5 mm (6.0 in)
Weight: 0.58 kg (1.28 lb)
Environment
Temperature:
Regular unit:
0 to 50C (32 to 122F)
Temperature-hardened version:
-22 to 70C (-7.6 to 158F)
Humidity: Up to 90%, noncondensing
Connector
RJ-45
RICi Family Product Comparison Table
Feature
RICi-E1, RICi-T1
(Ver. 2.1)
RICi-E3, RICi-T3
(Ver. 1.1)
RICi-4E1, RICi-4T1
RICi-8E1, RICi-8T1
(Ver. 2.0B)
RICi-16
(Ver 2.1)
Protocol Type
RAD HDLC
RAD HDLC
MLPPP (BCP)
HDLC IS
X.86 (LAPS)
GFP (G.7041), GFPoPDH

(G.8040)
VCAT (G.7043)
GFP (G.8040,
G.7041/Y.1303)
LCAS (G.7042)
Fault
Propagation
Yes
Yes
Yes
Yes
MAC Address
Table
512
512
2048
1024
QoS
VLAN Priority
(802.1p)
IP Precedence
VLAN Priority
(802.1p)
VLAN Priority
(802.1p)
DSCP
Per port
VLAN Priority (802.1p)

DSCP
Per port
QoS
Mechanism
Strict
Strict
Strict
Strict
Host VLAN
Yes
Yes
Yes
Yes
VLAN Stacking
Support
Yes
Yes
Yes
Yes
ph: 727-398-5252 / fax: 727-397-9610
Data Sheet
RICI-T1 RICI-E1
RICi-E1, RICi-T1
the unbalanced E1 option.
STANDARD CONFIGURATIONS
OPTIONAL ACCESSORIES
RICI-E1
RICI-E1/U
CBL-DB9F-DB9M-STR
Control port cable
RM-33-2
Hardware kit for mounting one or two
units in a 19-inch rack, for units with
plastic enclosures
SPECIAL CONFIGURATIONS
RICi-E1/!/$/?
RICi-T1/!/?
Legend
!
385-100-06/11 (2.1) Specifications are subject to change without prior notice. 19882011 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven,
and the product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
Note: The CBL-RJ45/2BNC/E1 cable is supplied with
Ordering
Power supply/enclosure:
24
24 VDC with
temperature-hardened metal
enclosure
Temperature range:
H
Wide-range power supply
(100 to 240 VAC or 48/60 VDC)
with temperature-hardened
plastic enclosure
Note: Only one of the above options can be
RM-35/@
Hardware kit for mounting one or two
units in a 19-inch rack, for units with
metal enclosures
@
Rack mounting kit type:

P1
Kit for mounting one unit
P2
Kit for mounting two units
WM-35
Hardware kit for mounting one unit on a
wall, for units with metal enclosures
selected, or neither. If neither of the above options

is selected, RICi-E1/T1 is supplied with a wide-range
power supply (100 to 240 VAC or 48/60 VDC), with
normal temperature range.
E1 interface type:
U
Unbalanced E1 interface
Note: The unbalanced E1 option is supported via

an adapter cable (CBL-RJ45/2BNC/E1, refer to
Supplied Accessories).
SUPPLIED ACCESSORIES
AC power cord
DC adapter plug
CBL-RJ45/2BNC/E1
Interface adapter for converting a
balanced E1 RJ-45 connector to a pair of
BNC unbalanced coaxial connectors
International Headquarters
24 Raoul Wallenberg Street
Tel Aviv 69719, Israel
Tel. 972-3-6458181
Fax 972-3-6498250, 6474436
E-mail market@rad.com
North America Headquarters

900 Corporate Drive
Mahwah, NJ 07430, USA
Tel. 201-5291100
Toll free 1-800-4447234
Fax 201-5295777
E-mail market@radusa.com
www.rad.com
Order
this publication by Catalog
No. 803522 / fax: 727-397-9610
order from: Cutter
Networks
ph: 727-398-5252
The Access Company

Rici E1t11

Uploaded by

Copyright:

Available Formats

Rici E1t11

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rici E1t11

Uploaded by

Copyright:

Available Formats

Data Sheet

Connect Fast Ethernet

Wire-speed packet forwarding

order from: Cutter Networks

RICi-E1 and RICi-T1 are intelligent

RICi-E1 and RICi-T1 are equipped with one

RICi-E1 and RICi-T1 comply with RADs

The VLAN Priority bits (802.1p) and IP

ph: 727-398-5252 / fax: 727-397-9610

The Access Company

The Fast Ethernet bridge handles

A built-in ping utility checks IP connectivity

VLAN stacking is used to tag direct user

The DHCP client automatically obtains the

The units feature fault propagation. When

A trace-route application quickly traces a

Providing Transparent LAN Services over Leased Lines

order from: Cutter Networks

ph: 727-398-5252 / fax: 727-397-9610

order from: Cutter Networks

ph: 727-398-5252 / fax: 727-397-9610

RAD proprietary HDLC compatible with

DC: 24 VDC (available only with

RICi Family Product Comparison Table

GFP (G.7041), GFPoPDH

VLAN Priority (802.1p)

order from: Cutter Networks

ph: 727-398-5252 / fax: 727-397-9610

the unbalanced E1 option.

Note: The CBL-RJ45/2BNC/E1 cable is supplied with

Note: Only one of the above options can be

Rack mounting kit type:

selected, or neither. If neither of the above options

Note: The unbalanced E1 option is supported via

North America Headquarters

The Access Company

You might also like