IM483 Manual
IM483 Manual
IM483 Manual
Mechanical Specifications
2.75
(69.9)
0.15
(3.8)
HMAX
2.45
(62.2)
1 2 3 4 5 6 7 8
3.00
(76.2)
P1, Pin 1
2.42
(61.4)
P2, Pin 1
0.29
(7.4)
0.03
(0.8)
1.00
(25.4)
4X 0.190 (4.1)
HMAX
IM483: 1.20 (30.5)
IM805: 1.32 (33.5)
Pin Configuration
See Opposite Side for alternative connector options.
Connector P1 (Signals)
Function
Pin #
+12 to +48 VDC, 2A (IM483) or +24 to +75 VDC, 3.5A (IM805) unregulated
linear or switching power supply.
22 AWG wire for logic and I/O, 18 AWG wire (IM483) or 16 AWG wire (IM805)
for power supply. Shielded twisted pairs recommended.
Direction Input
Optocoupler Supply
Enable/Disable Input
Motor Phase B
Reset Input
Motor Phase B
Fault Output
Motor Phase A
Fullstep Output
Motor Phase A
IM483
IM805
IM483
Condition
Min
Typ
Max
Unit
RMS
Peak
RMS
Peak
I/O Floating
I/O Floating
IOUT= 3A RMS
IOUT= 3A RMS
+12
+24
0.4
1
70
13
12
9
+48
+75
3.0
4
5.0
7.0
VDC
VDC
A
A
A
A
mA
mA
W
W
Condition
Min
Typ
Max
Unit
7.0
1.5
15
1.7
25
140
mA
VDC
VDC
mA
VDC
I/O Specifications
Input Forward Current
Input Forward Voltage
Input Reverse Breakdown Voltage
Output Current
Collector-Emitter Voltage
Isolated Inputs
Fault, Fullstep Outputs
Fault Output
Fault (ICS=25 mA)
0.2
VDC
Fullstep Output
Fullstep (ICS=25 mA)
6.5
100
VDC
Thermal Specifications
Min
Typ
Max
Unit
Storage Temperature
Ambient Temperature
Plate Temperature (Add't Cooling may be required)
-40
0
+125
+50
+70
C
C
C
Motion Specifications
Min
Typ
Max
Unit
10
14
MHz
6.00
(152.4)
0.85
(21.6)
5.50
(139.7)
3.51
(89.5)
Electrical Specifications
Drain-Source Voltage
Drain-Source On Resistance
General Specifications
No Connect
The IMx is designed to be mounted to a heat sink or inside a panel. IMS offers both a
Heat Sink Kit (H-4X) and Side Mounting Clips (U3-CLP)
Quiescent Current
Mounting Requirements
3.15
(80.1)
D
H-4X Heat Sink
0.50
(12.7)
IM483 or IM805
C
D
EQ. A
RADJ= IPEAK X 500
3 2 1
P2
= 500 X
8X 0.045 (1.14)
SQ. Post Tin
Plated Bronze
0.200
(5.1)
0.720
(18.3)
0.914
(23.2)
0.811
(20.6)
I RUN X I HOLD
I RUN
I HOLD
Connector P1
8X 0.025 (0.64)
SQ. Post Tin
Plated Bronze
0.200
(5.1)
0.820
(20.8)
EQ. B
R RED
Connector P2
5
5
8
8
+V
+12
+24
+40
+48
10
10
+75
15
Phase B
Phase B
Phase A
Phase A
0.200
(5.1)
P2:1
P2
Connector P1 and P2
Orientation
Power
Supply
8 7 6 5 4 3
P1:1
0.472
(12.0)
8X 0.040 (1.02)
SQ. Post Tin
Plated Bronze
Stepping Motor
Opto-Isolated Inputs
Current Limiting Resistor Values
+VDC
RLIMIT
10
681
12
15
24
1000
1300
2670
Controller
Output
0.500
(12.7)
+5 VDC
Controller
Output
Isolated Input
RLIMIT *
1/4 W 1%
Connector P1
0.41
(10.4)
1
Isolated Input
17
18
0.100
(2.54)
0.220
(5.6)
0.025
(0.6)
34
TTL Interface
ON/LOW/0
0.100
(2.54)
1 = MSEL0
2 = MSEL1
3 = MSEL2
4 = MSEL3
0.100
(2.54)
8X 0.025 (0.64)
SQ. Post Tin
Plated Bronze
0.520
0.800 (13.2)
(20.3)
8X 0.045 (1.14)
SQ. Post Tin
Plated Bronze
0.200
(5.1)
0.914
(23.2)
0.811
(20.6)
MSEL Switch
Resolution
Microsteps/Step
2
4
8
16
32
MSEL 0 MSEL 1
SW1:1
SW1:2
Binary Resolutions
400
0
0
800
1
0
1600
0
1
3200
1
1
6400
0
0
Steps/Rev
MSEL 2
SW1:3
MSEL 3
SW1:4
0
0
0
0
1
0
0
0
0
0
Connector P1
Pin #
64
12800
128
25600
256
51200
1000
2000
25
5000
50
10000
125
25000
250
50000
Function
Pin #
16, 26
Function
Resolution Select 3
On-Full-Step Output
21
Direction Input
22
Optocoupler Supply
23
Resolution Select 0
10
Enable/Disable Input
24
Resolution Select 1
12
Reset Input
25
Resolution Select 2
14
Fault Output
27
Decimal Resolutions
10
Connector P2
2.441
(62.00)
0.107
(2.72)
2.635
(66.92)
2X 0.155
(3.94)
+5 VDC
Supply*
+
-
Step Clock**
Stepping Motor
17
1
18
8
7
6
5
P2
4
3
2
1
Phase A
Phase A
Phase B
Phase B
+V
GND
RADJ
1
18
+
-
17
34
Power
Supply
Direction Switch**
** If an Opto Supply voltage greater than +5 VDC is used, a current
limiting resistor is REQUIRED in series with the Input!
0.780
(19.81)
34
1.050
(26.67)
www.schneider-electric-motion.us