Abb Fox System Specifications r8 RF 1khw002006

ABB Power Systems
FOX515
FOX System Specification
User Manual
User Guide FOX515 System Specification (R8)
User Guide
FOX515 System Specification
Platform FOX515 Release R8
Release History:
Release 7B:
Release 8B:
Release 8C:
February 2007
Dezember 2008
August 2009
Dezember 2009
May 2010
Copyright and Confidentiality: All rights of this document remain with

ABB Ltd (ABB). This document contains confidential information which is
the property of ABB. It must be held in confidence by the recipient and
may not be used for any purposes except those specifically authorised by
contract or otherwise in writing by ABB. This document may not be
copied in whole or in part, or any of its contents disclosed by the recipient
to any third party, without the prior written agreement of ABB.
Disclaimer:
ABB has taken reasonable care in compiling this document, however

ABB accepts no liability whatsoever for any error or omission in the
information contained herein and gives no other warranty or undertaking
as to its accuracy.
ABB reserves the right to amend this document at any time without prior
notice.
Document number:
1KHW002006
ABB Ltd
Power Systems
Bruggerstrasse 72
5400 Baden Switzerland
ABB Switzerland Ltd, 2010
The right to modifications or deviations due to technical progress is reserved.
1KHW002006
page 2 of 68
ABB
Table of contents
1
Common features system specification
General
ABB
9
9
Traffic functions
ATM traffic
IMA
CES
PDH traffic
SDH traffic
Ethernet over SDH Ethernet switching
Ethernet over SDH
Ethernet switching
Ethernet LAN to TDM WAN bridging
Power over Ethernet provisioning (PoE)
V5 functions
NGN Access Gateway
ADSL and SHDSL based broadband access aggregation
Conference functions
Protection
Monitoring of traffic signals
Diagnostic functions
11
11
11
12
12
13
14
15
15
16
16
17
17
18
20
21
21
22
Synchronisation
General
PETS
SETS
Maintenance and Diagnostics
Fault management
SSM and QL processing
23
23
23
23
25
25
26
System control and management functions

Control system
NE software system
Management functions
27
27
27
28
Performance control and diagnostic functions

System level
Functional level
Central diagnostics
29
29
29
29
Compatibility with other FOX equipment
30
Architecture
System
ABUS
31
31
32
page 3 of 68
1KHW002006
SBUS
PBUS
UBUS
32
32
32
Management communication
Element Manager
Management communication structures
Routing functions
34
34
34
35
Cross connections and delays

PBUS cross connect
Traffic signal delays PBUS and UBUS
Traffic signal delays SBUS and PBUS
ATM cell delays
Traffic delay CES
37
37
37
37
38
38
Protection switching restoration times

SNCP
MSP
IMA
N+1 equipment protection
39
39
39
39
39
Interfaces
Traffic interfaces
Synchronisation interfaces
Management interfaces
Alarm interfaces
Power interfaces
41
41
41
42
43
44
EMC/ESD and safety

EMC
ESD
Safety
45
45
45
45
Ambient and dependability

Ambient conditions
Dependability
46
46
47
2
FOX515 (subrack R2) supplementary
specifications
1KHW002006
49
Powering
DC interface
Internal power supply
Power dissipation
49
49
49
50
Subracks
FOX515
FANU5 fan unit
DUPI4 dual supply input
51
49
51
53
Dimensions and weight

Dimensions
Weight
55
55
55
page 4 of 68
ABB
Installation
Subrack, cable tray
Connection of signals
Connection of power supply
56
56
56
56
3
FOX512 (subrack R2) supplementary
specifications
ABB
59
Powering
DC interface
AC interface
DC battery backup interface
Power consumption
Power dissipation
59
59
59
60
60
60
61
Subracks
FOX512
FANU2 (R2) fan unit
BATMO battery package
62
60
62
64

Dimensions
Weight
65
65
65
Installation
Subrack, cable tray
66
66
66
66
67
page 5 of 68
1KHW002006
Precautions and safety

For generic information on precautions and safety refer to the precautions and safety user guide.
Referenced documents
1KHW002006
1KHW002000
Precautions and safety User Guide
1KHW002070
Release Note FOX / UCST
page 6 of 68
ABB
Technical support
ABB Technical Support is available as follows:
ABB Switzerland Ltd

Power Systems
Utility Communications
Bruggerstrasse 72
5400 Baden
Switzerland
ABB
Phone:
+41 58 589 37 35
or:
+41 844 845 845 (Call Center)
Fax:
+41 58 585 16 82
E-Mail:
utility.communication@ch.abb.com
URL:
www.abb.com/utilitycommunications
page 7 of 68
1KHW002006
1KHW002006
page 8 of 68
ABB
Common features system

specification
General
System application
- Multiservice access
- Traffic signal types
- Access multiplexing
- Multiplexing/demultiplexing
data and voice

PDH traffic
SDH traffic
VC-12, VC-3, VC-4
CAS
- Special traffic processing

- V5.x
- NGN Access Gateway
- Broadband Access Aggregation
V5.1, V5.2
protocol and user ports
H.248 / RTP (POTS)
SIGTRAN (ISDN-BA)
H.248 / MEGACO
(Set up / release control)
ADSL, ADSL2(+) line IF
SHDSL, SHDSL.bis line IF
ATM Ethernet IWF
Voice over IP
Broadband
- video multicast
- IP services
Gbit-Ethernet uplinks
P0-nc (n = 1 ... 31)
P12s / P12x (structured and
unstructured)
STM-1
STM-4
P12x and P0-nc
DXC 1/1 and 1/0
VC-4, VC-3, VC-12
ATM cells
IP packets
MAC frames
PoE class 1 3
and manual power set
- Bit-rates of traffic signals
ABB
- Cross connecting
- Routing
Bridging
- Power provisioning over Ethernet (PoE)
:
:
:
page 9 of 68
data and voice services

local and remote interfaces
PDH traffic
SDH traffic
ATM traffic
IP traffic
1KHW002006
1KHW002006
- Transmission
- Any mixture of above
Commissioning
- Traffic interfaces
- Traffic functions
- Functions
:
:
page 10 of 68
P0-nc (n = 1 ... 31)

P12
O22
E31/32
STM-1 (SDH)
(optical and electrical)
STM-4 (SDH)
(optical)
ATM cells
STM-1 (ATM)
(optical)
10BASE-T
100BASE-TX / FX
1000BASE-T / LX / SX
up to subrack and system
capacity
modular hardware
and software
core and modular functions
unit hardware and software
ABB
Traffic functions
ATM traffic
ATM traffic signals
- Cell format
- Service categories
:
:
UNI
CBR-rt (CBR.1)
CBR-nrt (CBR.1)
VBR-nrt (VBR.1)
UBR
ATM traffic functions

- Termination
- Services
VC-4 / ATM cells

IMA according to
AF-PHY-0088.001 V1.1
CES 2 Mbit/s (AAL1)
according to
AF-VTOA-0078.00 V2.0
LES (AAL2)
according to
AF-VMOA-0145.00 V2.0
- VP aggregating
- Interface (port)
- Oversubscription (egress traffic)
:
:
UNI (ATIOP)
1 100
- Cross connection
- Type
- Connections
:
:
PVCs
bi-directional
asymmetric
up 2048 VPC/VCCs
- Number
- Traffic control functions

- Ingress traffic (towards ABUS)
UPC (Usage Parameter Control)

CAC (Connection Admission
Control)
VP shaping (ATIOP)
CAC
- Egress traffic (from ABUS)
STM-1 interface
- Termination
- Multiplex Section Protection
:
:
physical section
with ATIOP
Support of remote ATM services

- Local FOX transmission interfaces
- Remote services (third party IAD/CPE)
ADSL (DMT)
G.SHDSL
data services
PSTN user ports
ISDN user ports
IMA implementation
- Function unit
- Application
:
:
IMA
- Number of IMA groups

Support of service classes
- 1 IMA group per unit
ABB
page 11 of 68
:
:
ACONV
provisioning of ATM cells via
P12 circuits according to
PHY-0086.001 (V.1.1)
up to 14 per unit
service classes CBR-rt, CBRnrt, VBR-nrt, UBR
1KHW002006
- IMA groups 2 14
- IMA group parameters (settable per interface)
- P12 links per group
- Cell frame length

- IMA group parameters (fixed)
- Group Symmetry Mode
1 service class (selectable)
up to 16
minimum required links per
group
32, 64, 128, 256 cells
- Maximum Differential Delay between links

- IMA group link synchronisation
- Transmission
- Reception
Symmetrical configuration
and operation
100 ms
:
:
CTC
CTC and ITC
- Scrambling function
activated
- Maintenance functions
- Performance monitoring
IMA group
Link group
loop back
cell counters
CES implementation
- Function unit
- Application
:
:
- Number of CES interfaces

- CES group parameters
- Type
- Supported functions
:
:
:
:
- Synchronisation of PDH traffic
8 Mbit/s signals
- Termination
- Protection 8 Mbit/s
:
:
- Multiplexing/demultiplexing from/into
2 Mbit/s signals
- Termination
- Protection 2 Mbit/s
:
:
- Adaptation
CES
ACONV
provisioning of
P12 circuits via ATM UNI
according to
AF-VTOA-0078.00 V2.0
up to 16 per unit
settable per service
2048 kbit/s (unstructured)
all functions of the FOX P12
traffic signal layer for
P0, P0-nc and P12x
synchronous (PBUS)
Adaptive
SRTS
traffic signal layer
traffic signal layer
PDH traffic
1KHW002006
page 12 of 68
physical section (optical)

1+1 physical section protection
4 P12 signals
unstructured or structured according to ITU-T G.704
physical section
1+1 physical section protection
SNCP/N and SNCP/I
structured, synchronous and
ABB
- Termination and monitoring
- Cross connection
- Special functionalities
:
:
unstructured signals
structured, synchronous signals
structured and unstructured
V5.x
PRA
NT1-PRA
NT1-LL
physical section
:
:
:
n x 64 kbit/s
0 600 kbit/s
DXC 1/0
Subrate multiplexing
- Synchronous
- Asynchronous
- Transparent
48/56 kbit/s (V.110/X.30)

0.6 38.4 kbit/s (V.110/X.30)
0.6 19.2 kbit/s (I.460)
0.6 38.4 kbit/s (V.110/X.30)
0.6 19.2 kbit/s (I.460)
0 0.3 kbit/s (V.110/X.30)
Support of local voice interfaces
PSTN (subscriber line)

PSTN (exchange line)
Magneto line
Voice / E+M
Support of remote PDH services and interfaces

DSL (CAP, PAM16)

SHDSL (PAM16)
8 Mbit/s optical
- Remote services (FOX CPE)
data interfaces
(n x 64 kbit/s, n = 1 32)
and subrates 0.33...56 kbit/s)
PSTN interfaces
PSTN user ports
ISDN-PRA
SDH traffic functions

- Termination
:
:
:
:
STM-4 according to
ITU-T G.707
for VC-12, VC-3 and VC-4
STM-1 according to
ITU-T G.707
for VC-12 and VC-3
VC-4 locally
VC-3 locally
VC-12 locally and remote
VC-12 and VC-3
VC-12, VC-3 and VC-4
VC-12, VC-3 and VC-4
Linear trail protection
SNCP
SNCP
n x 64 kbit/s traffic signals

- Termination
- Transport rates
- Synchronous
- Transparent
- Cross connection
SDH traffic
ABB
Add and drop

Through connection
Cross connection
Protection VC-12
- Protection VC-3 and VC-4

STM-4 and STM-1 interface
- Termination
- Multiplex Section Protection
page 13 of 68
physical section
(optical and electrical)
with SYN4E or with SYNIO or
with 2 SYNUF
1KHW002006
Support of remote SDH services

:
:
DSL (CAP, PAM16)

VC-12 termination and
data interfaces
Supported tributary traffic

- PDH
P12
E12
E31/32
STM-1 (electrical or optical)
- SDH
- Ethernet
-electrical
- optical
10BASE-T / 100BASE-TX /
1000BASE-T
100BASE-FX
1000BASE-LX / SX
Ethernet over SDH Ethernet switching
1KHW002006
Implementation
- Function unit
- Basic functions
- Physical interfaces
- Number of interfaces
- Interface types
:
:
up to 6
10BASE-T
100BASE-TX / 100BASE-FX
1000BASE-LX / SX
Transport (EoS)
- EoS
- Encapsulation procedure
- Virtual concatenation (VCAT)
- LCAS (Link Capacity Adjustment Scheme)
- Link protection
encapsulation of Ethernet
traffic for the transport via
SDH (VC-12, VC-3)
GFP framing according to
G.7041 (frame mapped)
VC-12 / VC-3 level
according to G.707
Protocol or fixed mode according to ITU-T G.7042
SNCP/N (VC-12 / VC-3)
Ethernet switching
- Switching points
- Number of VLAN instances
- VLAN support
Port and tag based

Tag stacking
Traffic prioritisation (4 levels)
4 queues (queuing profiles)
Rapid Spanning Tree
according to IEEE 802.1w
Physical layer
Transport layer
VC-12, VC-3 layer
- Ethernet PHY MIB-2, RMON
- GFP encapsulation
- VC-12, VC-3
:
:
:
packet (octet) counters

frame counters
counters
page 14 of 68
NEBRO
NEBRA
Transport (EoS)
Switching (Ethernet traffic)
Ethernet interfaces (6 / unit)

EoS endpoints (8 / unit)
up to 128
ABB
Ethernet over SDH

Implementation
- Function unit
SYN4E
- Basic functions
Transport (EoS)
- Interface types
:
:
4
10BASE-T, 100BASE-TX,
1000BASE-T
Transport (EoS)
- EoS
- Encapsulation procedure
- Virtual concatenation (VCAT)
- LCAS (Link Capacity Adjustment Scheme)
- Link protection
encapsulation of Ethernet
traffic for the transport via
SDH (VC-12, VC-3, VC-4)
GFP framing according to
G.7041 (frame mapped)
VC-12 / VC-3 / VC-4 level
according to G.707
Protocol or fixed mode according to ITU-T G.7042
SNCP/N (VC-12 / VC-3 /
VC-4)
Physical layer
Transport layer
VC-12, VC-3, VC-4 layer
- GFP encapsulation
- VC-12, VC-3, VC-4
:
:
:

frame counters
counters
Implementation
- Function unit
NEBRE, SWITE
Ethernet switching
ABB
- Basic functions
- Interface types
Switching (Ethernet traffic)
:
:
up to 6
10BASE-T
100BASE-TX / 100BASE-FX
1000BASE-LX / SX
Ethernet switching
- Switching points
Ethernet interfaces (6 / unit)
- Number of VLAN instances
up to 128
- VLAN support
Port and tag based

Tag stacking
Rapid Spanning Tree
Physical layer
page 15 of 68
1KHW002006
Ethernet LAN to TDM WAN bridging

Implementation
- Function unit
- Basic functions
- Number of LAN interfaces
- Interface types
Number of WAN interfaces

Interface types
ETER1
Bridging (Ethernet traffic)
:
:
up to 4
10BASE-TX half/full duplex
100BASE-TX half/full duplex
Access / Trunk
flow control
up to 64
PPP / HDLC encapsulation
and framing
Multilink PPP
Access / Trunk
:
:
Protection on WAN interfaces
1+1 SNCP/I for P0nc and

P12x signals
1+1 LTP for P0nc signals
Ethernet bridging
- Bridge instances
up to 8 logically independent
instances
- VLAN support
Port and tag based

shared VLAN learning
independent VLAN learning
star topology bridging
Rapid Spanning Tree
- Ethernet PHY MIB-2, RSTP
Unfiltered events
Physical layer
:
:

RSTP bridge counters
protection switching events
Implementation
- Function unit
SWITE
- Interfaces
- Powered device detection
6 access ports
10BASE-T/100BASE-TX
automatic according to
IEEE 802.3af
Available power
- max. power per SWITE board
- max. power per SWITE interface
- supported IEEE 802.3af power classes
:
:
:
Power over Ethernet provisioning (PoE)
63W
27W (manual power set)
class 1, with up to 4W
class 2, with up to 7W
class 3, with up to 15.4W
IP traffic
1KHW002006
page 16 of 68
ABB
IP traffic signals
- Routing functions
:
:
- Bridging functions
Support of remote PDH services

DSL (CAP, 2B1Q, PAM16)

SHDSL (PAM16)
LAN interfaces
(n x 64 kbit/s, n=1 32)
routing and bridging functions
:
:
:
:
:
:
PCONV
4
1
2
240
112
:
:
:
:
:
:
:
2 x 2 Mbit/s
PCON2
10
1
8
480
224
selectable for V5
MCAS
PSTN User Ports

- SUBH1, PHLC3
- SUBH3, PHLC2
- PHLC1 (2 x SUBH3)
- MUSIC 700 - LESI8
:
:
:
:
10 sub. line IFs

30 sub. line IFs
60 sub. line IFs
8 sub. line IFs
ISDN-BA User Ports

- ISBUQ (2B1Q)
- ISBUT (4B3T)
:
:
8 ISDN BA
8 ISDN BA
IPSMG
:
:
:
TDM <-> IP
RTP
ITU-T G.711, 64 kbit/s
PCM A-law, silent suppression (Appendix II)
P12s traffic
OSPF V2.0
Frame Relay
transparent MAC bridge
port based virtual LAN
star bridge
V5 functions
V5 protocol processing
- Function unit
- V5.1 interfaces
- V5.2 interfaces
- Max. number of V5.2 link accesses
- Capacity of PSTN user ports V5.2
- Capacity of ISDN BA user ports V5.2
incl. processing of p- and f-data
- Integrated IFs G.703 for V5 link access
- Function unit
- V5.1 interfaces
- V5.2 interfaces
- Max. number of V5.2 link accesses
- Capacity of PSTN user ports V5.2
- Capacity of ISDN BA user ports V5.2
incl. processing of p- and f-data
- Access for PSTN user ports
NGN Access Gateway

Access Gateway characteristics
- Function unit
- Media Gateway functions
- Voice conversion
- Voice (IP) transport protocol
- Codec types, characteristics
ABB
page 17 of 68
1KHW002006
- Modem- and FAX service
- Echo cancelling
- In-band signalling (DTMF, dial tone, ringing etc) :

DTMF relay service
:
- Clear channel
:
G.729 A (Codec) and B (silence suppression)

in-band transport supported
FAX relay service ITU-T T.38
ITU-T G.168
16 ms 128 ms
detection and generation
according to RFC 2833
64 kbit/s
(ISDN-BA B-channels)
- Signalling and control functions

- PSTN signalling conversion
- Set up / release control
- Interface to MGC
:
:
:
H.248 messages
H.248 / MEGACO
H.248.1 v1
primary and secondary
- Jitter buffer (accommodate IP delay variation)
- Max. number of active channels

- Traffic handling capacity (@ PDR < 0.04%)
:
:
200 ms
- fixed mode
- adaptive mode
200
10000 BHCA
:
:
ITU-T Q.931
SIGTRAN (IUA/SCTP)
Differentiated services (control and media traffic)
- VLAN
- VLAN tagging (control and media path)
- User priority (control and media path)
:
:
IEEE 802.1Q
IEEE 802.1p
User port access

Uplink interface
Functional parameterisation
Interoperability
:
:
:
:
16 x P12s (480 POTS)

10BASE-T / 100BASE-TX
Custom parameter sets
approved for selected MGC
brands
PSTN User Ports

- SUBH1, PHLC3
- SUBH3, PHLC2
- PHLC1 (or 2 x SUBH3)
- MUSIC 700 - LESI8
:
:
:
:
10 subscriber line IFs

ISDN-BA User Ports

- ISBUQ (2B1Q)
- ISBUT (4B3T)
:
:
8 ISDN BA
8 ISDN BA (on request)
Access Gateway characteristics

- Function units
- ADSL
- SHDSL
:
:
IPLM1, IPLM2, IPLM4

IPLM6
- Gateway functions
- ATM <-> Ethernet Encapsulation
Bridge mode (RFC 1483)

PPPoE (RFC 2516)
IPoE
PPPoA
- Signalling Gateway (ISDN-BA signalling)

- D-channel frames
- Interface to ASP
- Network IF
- Quality of service and resource allocation
ADSL and SHDSL based broadband access aggregation
1KHW002006
page 18 of 68
ABB
IPoA
- Layer 2 switching / bridging
- Modes
- Access control
- Learned MAC addresses
- STP support
:
:
:
- VLAN support
- Tagging
- Flooding and broadcasting

- Bridging modes for VLAN
:
:
- Port membership
- static
- dynamic
Frame tagging (IEEE 802.1q

and 802.1ad)
Tag stacking
Supported
Residential bridging
Restricted full bridging
Unrestricted full bridging
Lists of egress, inhibited,
untagged ports
GARP VLAN Registration
Protocol (GVRP)
- DHCP
Relay agent (RFC 2131)

Option 82 (RFC 3046)
- TV multicast support
- Number of groups
up to 256
- Group memberships
static
dynamic, IGMPv2 snooping
(RFC 2236)
- Quality of Service (QoS)

- Queues
- Scheduling mechanism
- Input rate limiting (IRL)

- Output rate limiting (ORL)
:
:
4 per ATM port

8 per physical Ethernet port
Strict priority
Minimum and maximum
bandwidth guarantees
Weighted excess bandwidth
distribution
per AAL5 interface (profiles)
per ATM / Ethernet port
- Access control
- Packet filtering
- Internet access control mechanisms
ABB
Static bridge forwarding

Dynamic bridging
Fix MAC address
(IEEE 802.1d)
Global / per port
up to 4000
ADSL/SHDSL ports
:
:
Filters / rules and decision

trees
MAC based authentication
MAC address control lists
IP address control lists
Sticky Bridge Ports
Forwarding database (FDB)
conflict traps
MAC address tracking
Dedicated queue for the control
plane per ADSL/SHDSL port
Uplinks
- Electrical interface
- Optical interfaces (IPLM1 only)
:
:
- Link Aggregation
100BASE-TX / 1000BASE-TX
100BASE-FX / 1000BASESX/LX SFP modules
LACP (IEEE 802.3ad)
ADSL access
- ADSL
ITU-T G.992.1
page 19 of 68
1KHW002006
- ADSL2
- ADSL2+
- Line rates
- Individually configurable
- upstream
- downstream
- Capacity
- Modularity
- Clusters
SHDSL access
- G.SHDSL
- G.SHDSL.bis
- Line rates
- Individually configurable
- ITU-T G.991.2
- ITU-T G.991.2 Annex F/G
- Pair bonding (2 pairs)
- Capacity
- Modularity
- Clusters
Management
- Unit and NE integration
:
:
ITU-T G.992.3
ITU-T G.992.5
:
:
:
in steps of 32 kbit/s
up to 1 Mbit/s
up to 24 Mbit/s
:
:
24 ports
up to 144 ports
:
:
ITU-T G.991.2
ITU-T G.991.2 Annex F/G
:
:
:
:
in steps of 8 kbit/s
200 kbit/s 2320 kbit/s
768 kbit/s 5696 kbit/s
SHDSL line according to ITUT G.994.1 Annex B
(for HS mode only)
:
:
24 ports
up to 144 ports
UCST / FOXMAN-UN
SNMP
CLI
(launch via UCST)
- IP DSLAM functionalities
Function unit
- Data type
:
:
- Processing for CAS signalling
- Max. number of participants

- Max. number of conferences
- Proposed max. number of participants
Parameters
- Attenuation of input signal
- Attenuation of output signal
- Noise suppression
:
:
:
:
:
:
:
Function unit
- Data type
:
:
- Processing for CAS signalling
- Max. number of participants

- Max. number of conferences
- Max. number of participants per conference
:
:
:
Parameters
- Attenuation of input signal
- Attenuation of output signal
- Noise suppression
:
:
:
:
1KHW002006
page 20 of 68
COBUV
A-law coded voice in P0, incl.
CAS
bit-wise AND of all input signalling
64
21
8
settable per participant
0, 3, 6 and 9 dB
0, 3 dB
selectable
3 steps
NEMSG
A-law coded voice in P0, incl.
CAS
bit-wise AND of all input signalling
32
8
17
settable per participant
0, 3, 6 and 9 dB
0, 3, 6 and 9 dB
selectable
3 steps
ABB
Protection
Section protection
Implemented by units with

transmission interface
Multiplex Section protection STM-4

- SDH
1 SYN4E
Multiplex Section protection STM-1

- SDH
1 SYN4E
1 SYNIO
2 SYNUF
2 ATIOP
2 Mbit/s (P12s)
(with PBUS units only)
VC-4, VC-3, VC-12
(on SYN4E)
2 Mbit/s and 64 kbit/s
(P12x, P0 and P0-nc)
(with PBUS units only)
VC-4, VC-3, VC-12
(on SYN4E)
VC-12
VC-3
- ATM
Subnetwork protection for signals
- SNCP/N
:
- SNCP/I
:
:
Linear trail protection
Equipment protection
- Traffic unit type
- units without front interfaces
- units with LAN front interfaces

- Protection type
:
:
- Unit switch-over
- Implications of EQP switch-over
Performance monitoring
Monitoring points
- PDH
ITU-T-G.826
- SDH
2 Mbit/s traffic signals

SULIC-NTU
(64 kbit/s TS required)
UNIDA
(64 kbit/s TS required)
VC-12
VC-3
VC-4
RS and MS in STM-1
RS and MS in STM-4
- ATM
-STM-1 UNI
- ATM traffic
ACONV
(EQP for SYNAC is a
FUTURE OPTION)
IPSMG
n+1
hot standby
non-revertive
automatic unit failure driven
and
UCST command
unit restart
restart of services
Monitoring of traffic signals
ABB
page 21 of 68
VC-4
RS and MS in STM-1
cell counters
1KHW002006
- Ethernet
- Ethernet PHY
event counters MIB-2

interface statistics
RMON
event counters MIB-2
interface statistics
RMON
GFP encapsulation counters
- Ethernet over SDH
Trail monitoring with TTI

- PDH
- SDH
:
:
2 Mbit/s (ECC mode)

VC-12
VC-3
VC-4
RS in STM-1
RS in STM-4
Function unit
Test purposes
:
:
COBUV and COBUX

channel performance
signal delays
Diagnostic functions
1KHW002006
page 22 of 68
ABB
Synchronisation
General
Basic configurations
:
:
:
PETS
PETS and SETS
SETS only
(PETS locked to SETS)
Function units
- PETS
- SETS
:
:
COBU<X>
SYNI<X>, SYNUF, SYN4E,
ATIOP
Selection algorithm
- QL based
- Priority based
- Switching
- Configurable Hold off time
- Configurable wait to restore time
:
:
:
:
:
QL 1 ... 15
1 ... 7/8 (1 highest)
revertive
0-60 s
0-720 s
:
:
:
P12s terminated
P12s monitored
P0 signals
- External 2048 kHz sources (ITU-T G.703)

- Internal source
:
:
2 (ESI-1 2)
50 ppm
Filter for clock recovery selectable
:
:
high Q
low Q
:
:
2.5 Hz
< 0.5 dB
:
:
40 Hz
< 0.5 dB
Synchronisation outputs (ESO)

- Number
- Squelching configurable per
:
:
3 (ESO-1 3)
- source selected
- QL of NE (1 ... 15)
requires two control units
Architecture
- NE level
- Inter sector SETS synchronisation
- SETS block diagram (per sector)
1 SETS system per

ABUS/SBUS sector
Agent sector synchronises to
Prime sector
see figure below
PETS
Timing sources for PETS
- Traffic signals (up to 4)
Jitter transfer characteristic

- High Q
- Max. Bandwidth
- Jitter gain
- Low Q
- Max. Bandwidth
- Jitter gain
SETS
ABB
page 23 of 68
1KHW002006
In ESO-4/ESO-SDH (T4) non

SETS locked mode, Select A
and Select B may share the
same timing sources, but they
are autonomous in terms of
selection.
Sync Sources:
SDH (T1)
STM-1
PDH (T2)
Select A
Select C
Squelch
2 Mbit/s
ESO-4/ SDH (T4)

2MHz
ESI-1 (T3)
2 MHz
Squelch
SETG
(PLL)
Select B
Int ernal Timing (T0)

SBUS, STM-1
SETS
Int ernal
1KHW002006
Specification
- Optimised for 2048 kbit/s hierarchy
- Accuracy under free-running conditions
- Minimum pull in range
- Wander generation in locked mode
:
:
:
:
- Wander tolerance
- Jitter tolerance for 2048 kHz, 2048 kbit/s
Option 1, ITU-T G.813

better than 4.6 ppm
4.6 ppm
Table 1, 2, 3 /G.813
Figure 1, 2 /G.813
Table 8, 9, 10 /G.813
Figure 5, 6, 7 /G.813
Figure 9/G.813
- Noise transfer characteristic

- Min Bandwidth
- Max. Bandwidth
- Gain in the pass band
- Short-term phase transient response
- Long-term phase transient response
- Phase response to input signal interruption
:
:
:
:
:
:
1 Hz
10 Hz
lower than 0.2 dB
Figure 12/G.813
Figure 14/G.813
G.813 10.3
Timing sources for SETS

- Traffic signals
- External 2048 kHz input (ITU-T G.703)
STM-1 MS (T1)
2 Mbit/s terminated (T2)
2 Mbit/s monitored (T2)
1 ESI-1 (T3)
Synchronisation Output (ESO)

- Number
- Mode of operation
:
:
- Squelching configurable per
Synchronisation Selection Process (Select B)

QL /SF hold off time
QL /SF wait to restore time
:
:
:
page 24 of 68
1 ESO-4/SDH (T4)
- SETS locked
- Non SETS locked
- selected source
- QL of NE (1...15)
Figure A.1/ETS 417-6-1
0 to 60s
0 to 720s
ABB
- SDH (SBUS)
- ATM (ABUS)
Relevant Standard Document
ETS 300 417-6-1
Selection
- Auto-selection (SETS Select B/A, PETS):
- Forced free-run
- Forced holdover
:
:
4.12
(QL-enabled mode corresponds
to QL based selection algorithm
QL disabled mode corresponds to Priority based selection algorithm)
Select A fix to Auto-selection
SETS Select B, PETS
SETS Select B (only if HO frequency available)
Timing source (SETS Select B, Select A, PETS)

- Forced switch according to ETS 300 417-6-1
- Manual switch
- Clear switch
- Set lockout
- Clear WTR
:
:
:
:
:
4.11.2.2
4.11.2.3
4.11.2.1
4.11.1.1
4.9
Status
- Timing Source
QL
Priority
Available
Failed
Not supervised
- SETS Clock operation mode
locked
free-run
holdover
- PETS Clock operation mode
(not applicable)
SETS (STM-4/1 aggregate unit)
Loss of External Clock source

Loss of clock source
PDH<X>/SDH<Y>
Loss of SEC Timing input
Loss of ESO Timing inputs
SEC Source not Primary
ESO Source not Primary
SETS in Holdover
SETS HW Failure
SEC Source out of limits
- PETS (COBU<X>)
Loss of external clock 1, 2
with 1 SYN4E unit or

with 2 SYNIF / SYNIC or
SYNUF units in the same
SBUS sector
with 2 ATIOP units in the
same ABUS sector
Maintenance and Diagnostics
Fault management
ABB
page 25 of 68
1KHW002006
Wrong impedance external

clock 1, 2
Loss of clock source PDH<X>
SSM and QL processing

SSM transmission
- in SDH signals
- in PDH signals
- SSM mode
- FOX proprietary ECC mode
1KHW002006
S1 byte of STM-4/1 MS
any Sa bit of 2 Mbit/s acc. to

G.704
Sa4 in bit of 2 Mbit/s acc. to
G.704,
Mapping of the QL
- in receive direction
SETS mapping table

overrides QL by QL 1 to 15
depending on received QL
- in transmit direction
SETS mapping table

overrides QL by QL 1 to 15
depending on NE QL
Unit routing table, ESO
SETS, PETS timing source configuration
override by Do not use

(QL = 15, SSI = 0, ESO =
squelched) depending on timing
source selected to avoid network
timing loops
assignment of a fix QL
page 26 of 68
ABB
System control and management functions

Control system
Basic control system
Central system control
:
:
Traffic units
distributed processor system

dedicated unit with master
processor
local slave processors
Management Information Base (MIB)

- Configuration data
- Unit software (units with SW download only)
:
:
:
control unit (COBU<X>)

MIB
MIB
Physical implementation of MIB
Capacity of PCMCIA card
PCMCIA card
(removable)
8, 16 MB
Equipment protection of the control unit

- Type of protection
:
:
- MIB of redundant unit

- Control unit switch-over
:
:
- Implications of the switch-over on traffic signals:

- automatic and UCST commanded switchover
- UBUS (UNIDA - UNIDA X.24)
:
- PBUS (LOMIF - LOMIF 2 Mbit/s transparent)
- removal of active control unit

- UBUS (UNIDA - UNIDA X.24)
- PBUS (LOMIF - LOMIF 2 Mbit/s transparent)
:
:
Real time clock
Unit software
- EM controlled SW download (for ESW)
- Control units
- Traffic units
:
:
1+1 (slots 11 and 12)

hot standby
non-revertive
permanently updated
automatic failure driven and
UCST command
short interruption
250 s
insertion of one 0-bit corresponding to an interruption of
488 ns
interruption 4 ms
insertion of 1 4 0-bits corresponding to an interruption
of 1952 ns
50 ppm
NE software system
- CPE
- FTP server based SW download (for ESW)

- CPE
- IP DSLAM
- ADSL
- SHDSL
ABB
page 27 of 68
COBU<X>
ABUS units
PBUS units
SBUS units
new UBUS units
MUSIC 200 (R4)
Line Runner SHDSL DTM
MUSIC 700 family
:
:
IPLM1, IPLM2, IPLM4

IPLM6
1KHW002006
- Embedded Software (ESW)
legacy UBUS units
Configuration management for
NE incl. ESW
traffic functions
Performance management for
NE
traffic signals
Management functions
1KHW002006
Fault management
- Hardware failures
- ESW configuration/operation
- Failures and performance
Alarm generation and reporting
- Generation and severity
- Indication
:
:
:
NE and units
units and CPE
traffic signals
:
:
- Reporting
programmable
local indicators and relay
contacts
alarm lists
logbook
remote access
Inventory management
for hardware and software
Management tools and versions

- FOX platform (NEs, units and CPEs)
- IP DSLAM functionality (IPLM<X>)
UCST R8B
FOXMAN-UN R8B
CLI
(launch via UCST)
page 28 of 68
ABB
Performance control and diagnostic functions

System level
System level
- Alarm system
- Alarm indicators
- Lists
:
:
- Inventory data
- Software installation status
Functional level
- Diagnostic
- Traffic functions
LED and relay contacts

NE fault list
logbook
for hardware and NE software system
for ESW installation and
installation progress
Functional level
- Synchronisation functions
- System functions
protected cross connections

U/PBUS usage
MSP
equipment protection
PETS, SETS
ESO SDH
system control /
equipment protection ECC
and OSPF router
Unit level
- Fault indicators
- Test loops
- State indication:
:
:
:
Central diagnostic for traffic signal channels

- Units with diagnostic function
- Functional blocks
:
:
COBUX, COBUV
Test signal generator
signal analyser
- Test signal
- Type
8-bit pattern and

pseudo random bit patterns
n x 64 kbit/s and 2 Mbit/s
unstructured
unit hardware and traffic

signals
unit specific
Traffic signals
Traffic signals G. 826
(selected units)
Central diagnostics
ABB
- Structure and bandwidth
- Analyses
- 8-bit pattern
- Pseudo random bit pattern
:
:
- Channel connection
page 29 of 68
matching patterns
performance monitoring
channel delay
via cross connect
1KHW002006
Compatibility with other FOX equipment

Compatible platform
FOX
Accommodation of legacy units in subrack
FOX traffic units (release for

FOX subracks as specified in
the release note)
Remote equipment
CPEs compatible with FOX

traffic units
Interfaces (applications based on the platform)
external traffic and management
Synchronisation
SSI
(P12s signals only)
- New units to existing systems
only if specified
- New front access connectors to existing system
not compatible
- UCST to legacy systems
FOX-U
FOX-U/M (-U/E)
DSL product family
Backward compatibility
1KHW002006
page 30 of 68
ABB
Architecture
System
System architecture
fully modular
open architecture
Implementation
configurable
according to requirements
- Control units
type COBU<X>
- Subsystems
MIB of the NE
PETS
Processing of Management
Com
Control of BUS access
UBUS access
Diagnostics
- Control units and supported features

- Diagnostics
COBUX, COBUV
- ECC
COBUX, COBUV
- Conference function
COBUV
- 8 x 2 Mbit/s
COBUX, COBUV
- 4 x 2 Mbit/s
COBUL
-128 x 2 Mbit/s
COBUX 212, 219 (R5)

COBUV 217, 220 (R5)
COBUL 216 (R4)
- 40 x 2 Mbit/s
COBUX 213, 223 (R5)

COBUV 218, 224 (R5)
control units R5
system control and

PETS
SETS
power supply
traffic units without front access or LAN interfaces
Implementation of external interfaces
on removable units
Unit types
- Units with ABUS access
ABUS units
- Units with PBUS access
PBUS units
- Units with SBUS access
SBUS units
- Units with UBUS access
UBUS units
- Units without (traffic) bus access
Special units
Unit software (EWS)
down loaded
System control
- UBUS highways
- PBUS highways
- ATM functionality
Functional levels of equipment protection
- System function level
- Traffic function level
ABB
page 31 of 68
1KHW002006
Compatibility to existing FOX equipment
for traffic units and functions
Configuration
software based with

UCST and FOXMAN-UN
Capacity
1215000 cells/s
Logical structure
ATM cells
UNI cell format
Physical structure
32 x 19.44 Mbit/s
per sector
linear with pairs of slots interleaved for MSP
- VC-4 terminating
2 x STM-1 (63 x VC-12 or

3 x VC-3))
- Add and drop to/from STM-4/1
VC-12 and VC-3
- Through connection
VC-12 and VC-3
Logical structure
63 x VC-12 (TU-12) or
3 x VC-3 (TU-3)
Physical structure
4 x 8 x 19.44 Mbit/s
per sector
linear with pairs of slots interleaved for MSP
Capacity
128 x 2 Mbit/s
with and without CAS
Logical structure
linear 128 x 2 Mbit/s

Physical structure
32 x 16 Mbit/s
non segmented linear
Capacity
8 x 2 Mbit/s
Logical structure
2 sets of highways each 4 x 2

Mbit/s
Physical structure
8 x 4 Mbit/s
segments, non linear
ABUS
SBUS
Capacity
PBUS
UBUS
1KHW002006
page 32 of 68
ABB
1 segment with overlapping

highway sets
ABB
page 33 of 68
1KHW002006
Management communication
Element Manager
Element Manager
UCST R8C
Element Manager System
FOXMAN-UN R8C
:
:
:
MCN for FOX

COBUV, COBUX
unnumbered PPP links with
dynamic OSPF routing
:
:
:
P12s
P0-nc
P12
:
:
:
STM-4/1 SOH bytes

192 kbit/s, 576 kbit/s
RS and MS (STM-4/1)
:
:
ATM cells
576 kbit/s
ATM, IMA
Management communication structures

ECC
- Application
- Function unit
- Structure
- ECC channels (MCN network)
- ECC over PDH
- Transport
- Bandwidth
- Traffic signal layer
- ECC over SDH
- Transport
- Bandwidth
- ECC over ATM
- Transport
- Bandwidth
- ATM characteristics
- QoS
- PCR
- CDVT
:
:
:
:
CBR (CBR.1)
80.1 (70.8) kbit/s
240.4 (212) kbit/s
720.4 (636) kbit/s
5000 (600) s
(Values in brackets apply up to the UCST R6A SP01)

- Encapsulation over ATM Adaptation Layer 5 :
- NE interfaces for PDH based ECC

- Number of channels
- Bandwidth PDH channels
- Use of interfaces
- NE interfaces for SDH based ECC

- Number of channels
- Bandwidth SDH channels
- Internal interfaces
1KHW002006
page 34 of 68
:
:
:
RFC 2364
(incl. AAL5 <-> P0-nc PPP
Relay function)
max. 32
64 1984 kbit/s (P0-nc)
16 kbit/s (TS0 in P12s)
ECC over PDH
ECC over ATM
(transport in ATM cells)
:
:
max. 8
ECC over SDH

(tunnelling in OSI DCN)
ABB
- Cumulated bandwidth PDH and SDH per NE

- NE ECC interface to MCN
:
:
- EM(S) interface to ECC
- ECC addressing
EOC
- Application
- Function unit
- Structure
:
:
:
max. 2048 kbit/s

P0-nc
(internal cross connect)
QX-interface (10BASE-T)
F-interface (RS-232C)
Tunnelling for
- OSI DCN
- ECC over ATM
IP addresses
:
:
:
management of legacy FOX

COBUV, COBUX
proprietary multi-path
based on SIFOX
SIFOX / F-interface
SIFOX / RS-232 C
proprietary EOC addresses
:
:
9600 bit/s
19200 bit/s
LAN (WAN)
- Type
- NE interface
- EM(S) interface
:
:
:
Ethernet 10BASE-T
QX-interface
Ethernet 10BASE-T
Q-BUS
- Structure
local bus
based on RS-485
NE management
access to remote Q-BUS via

remote FOX
COBUX, COBUV
remote replication of the managing Q-BUS interface
- NE interface to EOC
- EM(s) interface to EOC
- Addressing
Bandwidth
- Mixed NEs FOX-U/M (-U/E)/-U and FOX515
- NEs FOX515 only up to
- NE interfaces to Q-BUS
- Q1-slave interface
- Q1-master interface
- Purpose
- Implementation
- Function
- Management access to Q-BUS
- EM(S) direct access
- EM(S) access via Q1-master interface
- Addressing
- Bandwidth
- Mixed NEs FOX and legacy FOX
- NEs FOX only up to
:
:
RS-232 C via RS-232 C / RS485 converter

via FOX with Q1-master
interface
proprietary EOC addresses
:
:
9600 bit/s
57600 bit/s
COBUX, COBUV
COBUL
OSPF V2.0 (RFC 2178)
Routing functions
IP routing
- Function unit
- Routing protocol
- Router interfaces
- COBU<X>
- COBUX, COBUV
- COBUX, COBUV
ABB
page 35 of 68
:
:
:
:
F, Q1, QX,
OSI tunnel
ECC over
- PDH
- SDH
- ATM
1KHW002006
(ECC functionality not available with COBUL)
1KHW002006
OSI routing
- Function unit
- Routing protocol
- Router interfaces
:
:
:
COBUX, COBUV
IS-IS (level 1)
QX, OSI tunnels
HDLC routing
- Function unit
- Routing protocol
- Router interface
:
:
COBUX, COBUV
COBUL
proprietary
Q1-interface
page 36 of 68
ABB
Cross connections and delays

PBUS cross connect
Type
Capacity
- 2 Mbit/s equivalents max.
- 64 kbit/s equivalents max.
Protection between access ports
- Bi-directional (quality criteria for input selection)
non-blocking
structured and non structured
signals
:
:
128 x 2048 kbit/s

4096 x 64 kbit/s
2 Mbit/s
n x 64 kbit/s (n = 1 ... 31)
status monitor UCST
- Control
Broadcasting
2 Mbit/s
n x 64 kbit/s (n = 1 ... 31)
Delay assignment
- Single TS and consecutive TS n x 64 kbit/s
- Non consecutive TS n x 64 kbit/s
:
:
minimum delay
constant delay
Delays (access points cross connect)

- Unstructured signals P12x (PBUS - PBUS)
min.
max.
14 s
48 s
- Structured signals P12s (PBUS - PBUS)

- Minimum delay
min.
max.
min.
max.
21 s
380 s
21 s
501 s
min.
max.
min.
max.
21 s
378 s
21 s
499 s
min.
max.
min.
max.
125 s
248 s
125 s
369 s
min.
max.
min.
max.
125 s
246 s
125 s
367 s
typ.
typ.
139 s
583 s
Traffic signal delays PBUS and UBUS
- Constant delay
- Structured signals P12s (PBUS - UBUS)
- Minimum delay
- Constant delay
- Structured signals P12s (UBUS - PBUS))
- Minimum delay
- Constant delay
- Structured signals P12s (UBUS - UBUS)
- Minimum delay
- Constant delay
:
:
:
:
:
:
Traffic signal delays SBUS and PBUS

Delays (2 Mbit/s traffic signal reference)
- TM (loop on STM-4 or STM-1):
- SYNAM SYN4E SYN4E SYNAM
- LOMIF SYN4E SYN4E LOMIF
ABB
page 37 of 68
:
:
1KHW002006
- TM (loop on STM-1; X = F, O, C):

- SYNAM SYNI<X> SYNI<X> SYNAM
typ.
90 s
- ADM:
- SYN4E STM-4 VC-4 SYN4E STM-4
:
:
:
:
typ.
typ.
typ.
typ.
16 s
47 s
16 s
47 s
- ADM:
- SYNIO <m> IF_1 SYNIO <m> IF_2
typ.
16 s
ATM cell delays

STM-1 interface
- ATIOP (STM-1) ATIOP (STM-1)
IMA interface
- ATIOP (STM-1) ACONV (IMA, 2 links)
loopback
ACONV (IMA, 2 links) ATIOP (STM-1)
ADSL interface
- ATIOP (STM-1) ADAC<X>
ADSL modem (ATM)
Traffic delay CES

Delay of E1 signal(s) via CES
- LOMIF (P12) ACONV ATIOP (STM-1)
loopback
ACONV ATIOP (STM-1) LOMIF (P12)
1KHW002006
page 38 of 68
ABB
Protection switching restoration times

SNCP
Restoration time for a traffic signal with
- P0_SNCP/I
- PBUS
- UBUS
:
:
max.
max.
1.125 ms
1.125 ms
MSP
STM-4 SDH
- Restoration time for bidirectional MSP on section
- SYN4E - SYN4E
- typical
:
- maximum
:
25 ms
< 50 ms
STM-1 SDH
- Restoration time for bidirectional MSP on section
- SYN4E - SYN4E
- SYNIO - SYNIO
- SYNUF - SYNUF
- typical
:
- maximum
:
25 ms
< 50 ms
- SYN4E - other vendor equipment

- SYNIO - other vendor equipment
- SYNUF - other vendor equipment
:
:
:
not specified
not specified
not specified
STM-1 ATM
- Restoration time for MSP on section
- ATIOP ATIOP
- ATIOP - other vendor equipment
:
:
< 50 ms
not specified
IMA interface
ATIOP (STM-1) ACONV LOMIF
LOMIF ACONV ATIOP (STM-1)
- Restoration time ATM cells
- 1 link out of 2 fails
- 2 links out of 4 links fail
:
:
- Restoration time E1 (CES via IMA)
typical 8 ms
typical 8 ms
max. depending on
- link delay(s)
-M
- number of links
typically 50 ms
max. depending on
- link delay(s)
-M
- number of links
IMA
N+1 equipment protection
ABB
page 39 of 68
1KHW002006
1KHW002006
ACONV
- restoration time
not specified
depending on
- services
- traffic load
IPSMG
- restoration time
not specified
depending on
- services
- traffic load
page 40 of 68
ABB
Interfaces
Traffic interfaces
Implementation
Physical implementation
- Traffic interfaces
- Traffic functions
:
:
traffic units
traffic units and
control units
Characteristics and specifications

- Summary of units and specifications
- Details
refer to technical unit descriptions
Released units
specified per NE
refer to release note FOX /
UCST R8C Release Note
FOX / UCST
Function unit
COBU<X>
ESI-1:
- Synchronisation system
- Frequency
- Galvanic isolation from NE and battery
- Impedance
- According ITU-T G.703, section 10
:
:
:
:
:
:
SETS/PETS
2048 kHz
yes
configurable
75 or
120 (R2A)
| Zin | 3 k
:
:
:
:
PETS
2048 kHz
yes
configurable
:
:
75
| Zin | 3 k
Resistibility to surge voltages ESI-1 and ESI-2
1.2/50 s impulses
U = 100 V
Insulation signal pins of ESI-1 and ESI-2

- ECLK2MIN<X>
1 kV/50 Hz/60 s
Specification
Units implemented
Synchronisation interfaces
Inputs
- High impedance
ESI-2:
- Frequency
- Impedance
- Impedance
- According ITU-T G.703, section 10
- High impedance
ABB
page 41 of 68
1KHW002006
- ECLK2MGUARD<X> to earth
1 kV/50 Hz/60 s
ESO-1:
- Frequency
- Impedance according ITU-T G.703, section 10
:
:
:
:
PETS
2048 kHz
yes (R2A)
75
ESO-2 and ESO-3:

- Frequency
:
:
:
:
PETS
2048 kHz
no
75
ESO-4:
- Frequency
:
:
:
:
SETS
2048 kHz
yes (R2A)
75
120 (R2A)
Resistibility to surge voltages ESO-1 ESO-4
1.2/50 s impulses
U = 100 V
Insulation signal pins

- ESO-1 and ESO-4
- ECLK2MOUT<X>
- ECLK2MGUARD<X>
- ESO-2 and ESO-3
:
:
:
:
(R2A)
1 kV/50 Hz/60 s
1 kV/50 Hz/60 s
no galvanic separation
F-interface
- Application Layer
- Transport Layer
- Network Layer
- Data Link Layer
- Physical Layer
:
:
:
:
:
proprietary layer 7
TCP
IP
PPP
RS-232
Q1-interface
- Application Layer
- Transport Layer
- Network Layer
- Data Link Layer
- Physical Layer
:
:
:
:
:
proprietary layer 7
TCP
IP
PPP
RS-485
QX-interface
- Application Layer
- Transport Layer
- Network Layer
- Data Link Layer
- Physical Layer
:
:
:
:
:
proprietary layer 7
TCP
IP
IEEE 802.3 Ethernet
10BASE-T
half-duplex
Outputs
Management interfaces
EMS and FOX
1KHW002006
page 42 of 68
ABB
OSI-tunnel for TCP/IP management com.
Virtual LAN
via COBU<X>
Q1-master interface
- Application
- Physical Layer
Remote Q-bus master access

via COBUX, COBUV
RS-485
ECC interfaces MCN to FOX

- ECC over PDH
- ECC over SDH
- ECC over ATM
- FOX internal access for all ECCs
units supporting the

P12 traffic layer
RS and MS traffic layer (STM1)
ATM and/or IMA traffic layer
P0-nc via UBUS
:
:
:
:
P0-nc via UBUS

E1, E2 and F1
D1 D3
D4 D12
Function unit
COBU<X>
Alarm inputs:
- Number
- User defined names for input signals
- Active signal level
:
:
:
4
yes
configurable via EM
- active ground
- active open.
- Thresholds for detection

- Reference
- "Ground state range
- "Open state range
positive leg of the battery

(earth)
-8 V ... +75 V
with respect to reference
-75 V -16 V
with respect to reference
a current sink of at least 1 mA
with an impedance not higher
than 20 kOhm
to 1.2/50s surge impulses
with
U = 2000 V
COBU<X>
MCN to FOX
Access to SOH of STM-4/1

Access to SOH bytes
Order wire (EOW) and user channel
RS DCC (ECC via SDH)
MS DCC (ECC via SDH)
Alarm interfaces
ABB
- Load equivalent of input @ voltage of -16 V
- Surge immunity
- Physical implementation
Alarm outputs:
- Number
- Type
:
:
page 43 of 68
2
solid state relays
double throw
overload protected
1KHW002006
- Use
- Physical implementation
alarm status of NE
- "Urgent Alarm
- "Non-urgent Alarm
COBU<X>
- Current admissible
- Resistance
- Open contact leakage current @ 75V
- Open contact max. voltage
- Immunity
- Surges
- Voltage (any alarm output lead to earth)
:
:
:
:
< 50 mA
< 50 Ohm
100 A
150 V
to 1.2/50 s surge impulses

with
U = 2000 V
to 0.5A applied for 10 s
1 kV/50 Hz/60 s
:
:
active
not active
:
:
not active
not active
DC power interface
- Interface access
- Power converter units
:
:
FOX subrack *)
POSUM
POSUS
- DC/DC (primary to secondary voltage)

- POSUM @ +/-5 VDC (total)
- POSUS @ +5 VDC
:
:
16 A
10 A
:
:
POSUA
POSUA
16 A
- Current (between the alarm output leads)

- Insulation (any alarm output lead to earth)
Conditions at the alarm outputs in case of
- power fail
- "Urgent Alarm" output
- "Non-urgent Alarm" output
- inactive control unit
- "Urgent Alarm" output
- "Non-urgent Alarm" output
Power interfaces
AC power interface (FOX512 only)

- Interface access
- Power converter unit
- DC/DC (primary to secondary voltage)
- POSUA @ +/-5 VDC (total)
*) For details of the subrack power interfaces, refer to :
1KHW002006
page 44 of 68
FOX515
FOX512
complementary specifications
below
ABB
EMC/ESD and safety

EMC
Product family standard

Public Telecommunication network equipment
EN 300 386 V1.3.3
Interference voltage 0.15 MHz ... 30 MHz

- DC power supply IF
- AC power supply IF (POSUA)
- traffic signal IFs
:
:
:
EN 55022, class A
EN 55022, class B
EN 55022, class B
Radiated field 30 MHz ... 1000 MHz
EN 55022, class B
IEC/EN 61000-4-3
IEC/EN 61000-4-6
Emission
Immunity
Electromagnetic field
80 MHz ... 2000 MHz, level 3, 10 V/m
Conducted common mode HF disturbance
150 kHz ... 80 MHz,
modulated 1 kHz 80% AM, 3 V
Fast transients/bursts
- on power supply IF (CDN)
- on traffic signal IFs (capacitive clamp)
Surge immunity
- Traffic and control IFs
:
:
:
IEC/EN 61000-4-4
1 kV
0.5 kV
- Power supply interface

- Common mode
:
:
EN 300 386 V1.3.2 and

ITU-T K.20
IEC/EN 61000-4-5
1 kV
1.2/50 s (8/20s)
0.5 kV
1.2/50 s (8/20s)
- Differential mode
Electrostatic Discharge
- contact discharge
- air discharge
:
:
:
IEC/EN 61000-4-2
6 kV
8 kV
Safety according to
IEC/EN 60950-1
ESD
Safety
ABB
page 45 of 68
1KHW002006
Ambient and dependability

Ambient conditions
Storage
All equipment (exclusive batteries) according to
ETS 300 019-1-1

class 1.2
-25C ... +55C
according to class 1.2
Not specified
According to the specifications of the battery supplier
Temperature range
Humidity
Biological and chemical active substances
Batteries (BATMO option)
:
:
:
:
ETS 300 019-1-2

class 2.2
Transport
Temperature ranges
- ambient air for unventilated enclosures
- ambient air for ventilated enclosures or outdoor
Humidity
Vibration random Acceleration Spectral Density
- ASD @ 10-200 Hz
- ASD @ 200-2000 Hz
Batteries (BATMO option for FOX512)
:
:
:
-25C .. +70C
-25C .. +40C
:
:
:
:
1.0 m2s-3
0.3 m2s-3
Not specified
ETS 300 019-1-3

class 3.2
Temperature range system (extended)

- Operation
- without forced ventilation *)
- with forced ventilation
- Start up temperature
Humidity
:
:
:
:
-20C ... +55C

-20C ... +70C
-20C
up to 95%, non-condensing
Direct ambient temperature range units (PBUS,

ABUS, SBUS, new UBUS, control, power units)
- Range of operation
- Compliant with specifications
:
:
-20C ... +85C

0C +70C
Not specified
Batteries (BATMO option for FOX512)
Operation
*) forced ventilation is mandatory for some units
1KHW002006
page 46 of 68
ABB
Dependability
Availability
Mean accumulated down time (MADT)
traffic between any two 2 Mbit/s ports of 2 NEs
< 10 min. per year

(excluding failures of the
transmission media)
Calculated MTTF for all categories of failures

- Single unit
- Detailed MTTF figures per unit
Predictions based on
:
:
:
> 20 years
refer to the unit descriptions.
MIL-HD BK-217F
MTTF
MTTF values of operating systems are available on request.
ABB
page 47 of 68
1KHW002006
1KHW002006
page 48 of 68
ABB
FOX515 (subrack R2) supplementary specifications
FOX515 (subrack R2)

supplementary specifications
Powering
DC interface
Power supply interface according
Voltage range for operation
ETS 300 132-2

interface A
-40 VDC -72 VDC
Power consumption
- Maximum continuous current
- Maximum admissible power consumption
:
:
30 A
1200 Watt
Recommended fusing
max. 30 A slow blow
Connection points for power supply circuits

- External supply circuit(s)
1 interface or 2 interfaces (for

dual power supply)
on the cable tray
- Subrack power interfaces

- Single power supply
- Dual power supply
:
:
1 interface
2 interfaces (DUPI4 option)
DC/DC power conversion
POSUM
POSUS
Operation of power supply units

- Parallel operation of units
- Number of units operating in parallel
:
:
load sharing
5
Protection and load sharing

- Protection type
- Life insertion of converter units
:
:
n + 1 (n = 0 ... 4)
yes
Conversion
Protection
ABB
page 49 of 68
1KHW002006
Power dissipation
Maximum power dissipation
Maximum admissible power dissipation PD in
the FOX subrack (for ambient conditions)
- Natural air convection
(evenly distributed units in the subrack)
- Forced ventilation/air conditioning
- Range (with FANU5)
- Ventilation mandatory
depending on traffic interfaces
PD 150 W totally and

PD < 11 W in any slot
:
:
PD 1200 W totally
PD > 150 W totally or
PD 11 W in any slot
provided that specified ambient conditions are fully met *)
- Fan unit for FOX515
FANU5
1KHW002006
page 50 of 68
ABB
Subracks
FOX515
Construction
Card cage for FOX units
Modularity
:
:
19-inch practice
subrack
cable tray
heat deflection shield
fan unit
Installation into racks

- 19 inch
- ETSI (applicable standard ETS 300 119-4)
:
:
direct
with adapters
Basic construction
- Sides and rear
- Top and bottom
- Front
:
:
:
:
metallic
sheet metal
perforated sheet metal
front cover

- Connection principle
- Supply modes
:
:
- Support of dual power supply
integrated connector(s)
single and dual power supply
supported
DUPI4 option
mechanically and electrically
integrated in the FOX515
subrack
Connection of signal cables

- Shields of signal cables
- Cable installation and strain relief
:
:
grounding bars in front

matching cable tray
Slots
- Number of slots
- Slot width
:
:
21
20.32 mm
4 TE
Segmentation of access
- ABUS
- PBUS
- SBUS
- UBUS
:
:
:
:
14 slots (2 sectors)
20 slots
14 slots (2 sectors)
21 slots
Allocation of units to slots
flexible
slot 11 dedicated
Unit construction
19-inch practice
1 HU (44.45 mm)
Capacity and slots
FANU5 fan unit

Construction
ABB
page 51 of 68
1KHW002006

- 19-inch
:
:
direct
with adapters
Connection of signal and power cable
front access
Number of fans
10
Operation
Temperature control of the fan speed
- minimum speed
- maximum speed
temperature controlled
:
:
20 C
35 C
Performance, average
- minimum speed (free blowing)
- air velocity
- transported air volume
- pressure drop
- noise
:
:
:
:
1 m/s
3
350 m /h
25 Pa
53 dBA @ 1 m
- maximum speed (free blowing)

- air velocity
- pressure drop
- noise
:
:
:
:
2 m/s
3
600 m /h
80 Pa
66 dBA @ 1 m
Types
- Optical indicators:
- Unit powered
- Partial unit failure
- Total unit failure
:
:
:
1 green LED
1 yellow LED
1 red LED
- Electrical contacts:
- Type
- Current
- Voltage drop @ 10 mA
- Open contact maximum voltage
:
:
:
:
:
solid state
10 mA
2V
-75 V
protected against reverse polarity
100 A
Connector
Molex Mini-Fit Jr.
Voltage range
- nominal
- range
- switch on voltage (power up)
- switch off voltage (power down)
- resistance to reverse polarity
:
:
:
:
:
-48 VDC
-39.5 VDC -75 VDC
-35 VDC
-27 VDC
+75 VDC
Power consumption (-48 VDC battery)

- minimum speed (all fans operating, T < 20 C)
- maximum speed (all fans operating, T > 35 C)
:
:
0.6 A
1.2 A
Connector
Molex Mini-Fit Jr.
Specification
Alarm interface
- Leakage current @ -75 V
Power supply
1KHW002006
page 52 of 68
ABB
Ambient conditions
according to common features system specification, except
Operation
Temperature range
Minimum start up temperature
Humidity
:
:
:
-10C ... +70C

-25C
up to 95%, non-condensing
Overall dimensions (W x H x D)
Construction
Weight FANU5 without packaging
Weight FANU5 power cable
Weight ETSI adapters 1 HU
:
:
:
:
:
482.6 x 43.6 x 248.6 mm

19 inch and ETSI mounting
2.79 kg
0.06 kg
0.05 kg
- MTTF for partial unit failure

- MTTF for total unit failure
:
:
> 5 years
> 1000 years
Power inputs
U1
U2
Power output to FOX
UTF
Alarm outputs
Supervision U1
Supervision U2
Input voltage range
-39.5 ... -75 VDC
Maximum reverse polarity
+75 VDC
Maximum output current
30 A
Typical power dissipation at maximum current
10 W
Mechanical parameters
Reliability
MTTF @ 35C ambient temperature
DUPI4 dual supply input

Interfaces
Specifications
ABB
page 53 of 68
1KHW002006
Alarm interface
Alarm threshold voltage
-33 3 VDC
Electrical contacts:
- Type
- Current
- Voltage drop @ 10 mA
- Open contact maximum voltage
- Leakage current @ -75 V
:
:
:
:
:
solid state
10 mA
2V
-75 V
100 A
Connector
Molex Mini-Fit Jr.
Installation
Mechanically integrated in
FOX515 subrack
Overall dimensions (W x H x D)
438 x 31.7 x 52.6 mm
Weight without packaging
0.41 kg
MTTF @ 35C
1610 years
Mechanical parameters
Reliability
1KHW002006
page 54 of 68
ABB

Dimensions
19-inch subrack without front cover (W x H x D)
19-inch subrack with front cover (W x H x D)
Cable tray (W x H x D)
Heat deflection shield (W x H x D)
:
:
:
:
482.6 x 309.5 x 280.4 mm

482.6 x 309.5 x 284.1 mm
482.6 x 87.1 x 240.2 mm
482.6 x 87.8 x 228 mm
Construction and layout
19-inch and ETSI mounting

practice
Weight
ABB
19-inch subrack (without units) without front cover :

Front cover
:
6..81 kg
1.13 kg
Cable tray
Power cable with WAGO connector block
:
:
0.53 kg
0.08 kg
Heat deflection shield
1.27 kg
ETSI adapters (set)

- 2 HU
- 8 HU
- 9 HU
- 10 HU
- 11 HU
:
:
:
:
:
0.09 kg
0.36 kg
0.41 kg
0.45 kg
0.49 kg
Weight of options (FANU5, DUPI4)

Weight of units
:
:
refer to option specification

refer to unit descriptions
page 55 of 68
1KHW002006
Installation
Subrack, cable tray
Construction and installation
Height of subrack and cable tray
Installation into ETSI racks
Torques
- 19-inch / ETSI equipment and adapters M6 (4.8)
- DUPI4 unit
- Grounding/bonding terminal
- Unit front covers M2.5
:
:
:
19-inch practice
8 HU (= 355.6 mm)
with adapters
:
:
:
:
max. 4.7 Nm
max. 0.34 Nm
max. 2.0 Nm
max. 0.56 Nm
Traffic signals (new FOX units)
:
:
:
:
:
DIN 41 612
32 pins, rows a, c (b)
unit
proprietary
where applicable
yes
grounding bar, cable tray
Male connector
Connector cover
Coding keys
Latching system
Strain relief
Traffic signals (old FOX units)

Management interfaces (control unit)
- F-interface
- QX-interface
refer to FOX-U description
:
:
- Q1-interface
- Strain relief
SUBMINI D, 9 p./f.
10BASE-T (RJ-45)
half-duplex
DIN 41 612
8 pins, rows a, c
latching system
Auxiliary signals (control unit)

- Synchronisation inputs/outputs
- Alarm inputs/outputs
- Latching system and coding keys

- Strain relief
:
:
DIN 41 612
8 pins, rows a, c
DIN 41 612
8 pins, rows a, c
yes
EMC protection of signal interfaces

- Signal cables with shields
- Signal cables without shields
:
:
grounding bar of subrack

toroidal core ferrite
Mechanical shock and vibration
ETS 300 019-1-3
Subrack (internal access for power supply)

- Number of power interfaces
- Connector type
1 standard
2 with DUPI4 option
4 pin FAST-ON type connector
Cable tray (external access for power supply)

- Number of power interfaces
1KHW002006
page 56 of 68
ABB
- Connection
Power cables (subrack connector WAGO block)

- Cable provisioning
:
- Cross section per cable section
ABB
page 57 of 68
2 with DUPI4 option

4 pin WAGO connector
block(s)
1 cable provided with
- subrack
- DUPI4 option
2
5 mm
1KHW002006
1KHW002006
page 58 of 68
ABB
FOX512 (subrack R2)

supplementary specifications
Powering
DC interface
ETS 300 132-2

interface A
Interface access
subrack
Nominal input voltages (POSUM/POSUS)

- -48 VDC, voltage range
- -60 VDC, voltage range
:
:
-40.5 VDC -57 VDC

-50.5 VDC -72 VDC
Maximum continuous input current

Recommended fusing
:
:
10.0 A
10 A slow blow
Connection points for power supply circuits

- Standard
- Protected
1
on the cable tray
2
with DUPOS
ETS 300 132-1

interface A
Interface access
POSUA
Nominal input voltages

- 115 VAC, voltage range
max. 90 % of rated power
- 230 VAC, voltage range
max. 90 % of rated power
:
:
:
:
88 VAC 132 VAC

88 VAC 99 VAC
176 VAC 264 VAC
176 VAC 198 VAC
Frequency
45 Hz 63 Hz
Operation of POSUA from DC power sources
not possible
Max. converted power (internal -48 VDC rail)

- Nominal power @ 115/230 VAC
- 88 99 VAC / 176 198 VAC
:
:
140 W
126 W
AC interface
ABB
page 59 of 68
1KHW002006
Max. current (internal -48 VDC rail)
2.8 A
Maximum continuous input current

- 115 VAC
- 230 VAC
:
:
< 2.0 A
< 1.0 A
Interface access
POSUA
Charger interface
- nominal voltage @ 20C
- temperature compensation
:
:
-54.8 VDC
+110 mV/C
Max. power drain from battery
3A
Protection of the battery from excessive

discharging
- Switch OFF for battery drain
- Switch ON for battery drain
:
:
:
via FET switch (POSUA)

UTF = -42 VDC 1.5 VDC
after mains restart
Interface protection BATMO side

- Protection via
- Time to high impedance
:
:
self-healing PTC fuse

< 60 ms
Max. cable length between POSUA and BATMO
3 m / 3 x 1.5 mm
Maximum admissible power consumption

- DC power interface
- Mains power interface
:
:
320 W
180 W
DC/DC (primary to secondary voltage)
POSUM
POSUS
POSUA
AC/DC (mains to primary voltage)
POSUA
DC/DC conversion with the POSUM/POSUS

- unit protection
- load sharing
- life insertion of converter units
:
:
:
1+1
yes
yes
AC/DC conversion with the POSUA

- unit protection
- protection of the AC/DC conversion
:
:
no
no (only 1 unit)
protection of primary voltage
DC battery backup interface
Power consumption

Conversion
Protection
1KHW002006
page 60 of 68
ABB
- load sharing
- life insertion of converter units
:
:
via battery backup

not applicable
no
DC/DC conversion with the POSUA

- protection of DC/DC conversion
- load sharing
- life insertion of
- POSUM/POSUS
- POSUA
:
:
with POSUM/POSUS
yes with POSUM/POSUS
:
:
yes
no
Concurrent power supply of the FOX512 via

mains (POSUA) and the
- BATMO battery backup
- DC power supply terminal of the subrack
:
:
yes
not possible
Maximum power dissipation
depending on traffic interfaces and installation
Maximum admissible power dissipation

- Natural air convection (for specified ambient)
PD 60 W totally and
PD < 11 W in any slot
- Forced ventilation or air conditioning

Mandatory for PD range
60 W < PD < 320 W totally or

11 W < PD < 40 W in any slot
Power dissipation
Vertical installation
provided specified ambient

conditions are fully met *)
Horizontal installation
Maximum admissible power dissipation
- Natural air convection (for specified ambient)
- Forced ventilation with FANU2 (R2) fan unit
:
:
not admitted
PD 320 W
provided specified ambient conditions are fully met *)

ABB
page 61 of 68
1KHW002006
Subracks
FOX512
Construction
Card cage for FOX units
Modularity
:
:
proprietary subrack
versatile subrack with
- 19-inch adapter
- ETSI adapters
- wall-mounting adapter

- 19-inch
:
:
with adapter
19-inch with adapters
Installation on walls and in cabinets
with adapter
Basic construction
- Sides and rear
- Top and bottom
- Front
Connection of signal and power cables
- Power supply (DC)
- Shields of signal cables
- Cable installation and strain relief
:
:
:
:
metallic
sheet metal
perforated sheet metal
front cover
:
:
:
integrated connector
grounding bars in front
installation adapters with
cable tray
Slots
- Number of slots
- Slot width (standard slots)
8 standard
1 special for fan unit
20.32 mm
4 TE
Segmentation of access
- ABUS
- PBUS
- SBUS
- UBUS
:
:
:
:
5 slots
7 slots (incl. slot 11)
5 slots
8 slots (incl. slot 11)
Allocation of units to slots
flexible
slot 11 dedicated
Unit construction
proprietary for the FOX512

subrack
Installation
in slot 1of the subrack
Connection of signals and power
all internal connections
Capacity and slots
FANU2 (R2) fan unit

Construction
Specification
1KHW002006
page 62 of 68
ABB
Number of fans
Operation
temperature controlled
- low speed
- high speed
Temperature control of the fan speed

- low speed
- high. speed
:
:
< 27 C
> 45 C
Performance (average)
- low speed (free blowing)
- air velocity
- noise
:
:
:
1 m/s
3
70 m /s
46 dBA @ 1 m
- high speed (free blowing)

- air velocity
- noise
:
:
:
2 m/s
3
120 m /s
56 dBA @ 1 m
Types
- Optical indicator
- Local failure indicator
- Failure and alarm indication
:
:
1 red LED
integrated with the FOX
alarm system
- Electrical contacts
- Local contacts
- Failure and alarm indication
:
:
none
integrated with the FOX
alarm system
Connection to the COBU<X>
Supply circuit
-48 VDC
(internal power rail)
Power consumption (-48 VDC rail, typical)

- low speed (both fans operating, T = 27 C)
- high speed (both fans operating, T > 45 C)
:
:
< 120 mA
< 250 mA
Alarm interface
Power supply
ABB
page 63 of 68
1KHW002006
Reliability
MTTF @ 35 C ambient temperature
- MTTF for partial failure
- MTTF for total unit failure
:
:
> 50 years
> 1000 years
Connection of power supply, alarm signals
Basic construction
- Sides
- Rear
- Top and bottom
- Front
Battery power cable
:
:
:
:
:
:
Proprietary metal case

sheet metal
open
sheet metal
front cover
3-pin WAGO plug
Number of batteries (12 VDC) required
4 (48 VDC)
Battery type
- Nominal voltage
- Nominal capacity
Mechanical parameters:
- Dimensions max. (W x H x D)
- Weight
- Cable terminals
Recommended commercial grade batteries
:
:
maintenance-free
lead batteries
12 VDC
17 Ah

Battery case
Batteries
Expected lifetime for

- 20 % loss of capacity
- operation at 20 C
Performance vs. temperature
- Operation (with reduced performance)
- Temperature range for correct charging
- Reduction of the battery capacity by
- 20 % at
- 50 % at
:
:
:
:
77 x 168 x 183 mm
ca. 6.5 kg
bolts and nuts M5
YUASA NP17-12I
Panasonic LC-RD1217P
or equivalent products
up to 4 years
:
:
-10 C + 55 C
-10 C + 40 C
:
:
0 C
-20 C
Other battery types might have different parameter specifications.
1KHW002006
page 64 of 68
ABB

Dimensions
Subrack without front cover (W x H x D)
Subrack with 19-inch adapter (horizontal view)
- without front cover (W x H x D)
- with front cover (W x H x D)
Subrack with ETSI adapters (horizontal view)
177.0 x 458.8 x 279.7 mm
:
:
482.6 x 177.0 x 279.7 mm

482.6 x 177.0 x 283 mm
:
:
532.6 x 177.0 x 279.7 mm

532.6 x 177.0 x 283 mm
Subrack with wall-mounting adapter

:
:
177.0 x 510 x 286.2 mm

177.0 x 510 x 289.5 mm
Construction and layout
proprietary, adaptable for 19inch and ETSI mounting

practice
(refer to figures)

- without rear flanges ( W x H x D)
- with flanges ( W x H x D)
:
:
188 x 425 x 206 mm

227 x 425 x 206 mm
Subrack (without units, FANU2)

- with front cover
- without front cover
:
:
4.71 kg
4.07 kg
Subrack with front cover (without units)

- with 19-inch adapter
- with ETSI adapters
- with wall-mounting adapter
:
:
:
4.89 kg
5.06 kg
5.67 kg
FANU2 fan unit

Dummy cover for FANU2 slot
Dust filter unit
:
:
:
0.64 kg
0.07 kg
0.11 kg
Weight of units
- case without batteries
- case with batteries
refer to unit descriptions
:
:
4.2 kg
ca. 32 kg
Weight
ABB
page 65 of 68
1KHW002006
Installation
Subrack, cable tray
Construction and installation
proprietary with installation

adapters for
horizontal and vertical installation
Width (horizontal height) of subrack
4 HU (= 177 mm)
Installation
- in 19-inch racks (horizontal, vertical)
- in ETSI racks (horizontal, vertical)
- on walls or in cabinets (vertical)
:
:
:
with adapter
with adapters
with adapter
Cable tray
19-inch adapter
wall-mounting adapter
Torques
- 19-inch / ETSI equipment and adapters M6 (4.8) :
- Angle bracket M4 (4.8)
:
- Unit front covers M2.5
:
max. 4.7 Nm
max. 1.3 Nm
max. 0.56 Nm
Installation
- wall- and cabinet-mounting
- ground installation
:
:
via screws or similar.

stand alone on the ground
Traffic signals (new FOX units)
:
:
:
:
:
DIN 41 612
32 pins, rows a, c (b)
unit
proprietary
where applicable
yes
Traffic signals (old FOX units)
refer to FOX-U description
Management interfaces (control unit)

- F-interface
- QX-interface
:
:
- Q1-interface
- Strain relief
Auxiliary signals (control unit)
- Synchronisation inputs/outputs
SUBMINI D, 9 p./f.
10BASE-T (RJ-45)
half-duplex
DIN 41 612
8 pins, rows a, c
latching system
- Alarm inputs/outputs
1KHW002006
Male connector
Connector cover
Coding keys
Latching system
Strain relief
page 66 of 68
DIN 41 612
8 pins, rows a, c
DIN 41 612
ABB
- Latching system and coding keys

- Strain relief
:
:
8 pins, rows a, c
yes
EMC protection of signal interfaces

- Signal cables with shields
- Signal cables without shields
:
:
grounding bar of subrack

toroidal core ferrite
Mechanical shock and vibration
ETS 300 019-1-3
Subrack (internal access for power supply)
Cable tray (external access for power supply)

Mains
:
:
3-pin FAST-ON type connection

(cable provided with subrack)
3-pin WAGO connector block
POSUA front
3-pin apparatus plug
Interface for the external backup battery
ABB
page 67 of 68
POSUA front
3-pin WAGO plug
1KHW002006
For more information please contact:

ABB Switzerland Ltd
Power Systems
Utility Communications
Bruggerstrasse 72
5400 Baden
Switzerland
Phone: +41 58 589 37 35
or: +41 844 845 845 (Call Center)
Fax: +41 58 585 16 82
E-Mail: utility.communication@ch.abb.com
www.abb.com/utilitycommunications

Abb Fox System Specifications r8 RF 1khw002006

Uploaded by

Copyright:

Available Formats

Abb Fox System Specifications r8 RF 1khw002006

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Abb Fox System Specifications r8 RF 1khw002006

Uploaded by

Copyright:

Available Formats

ABB Power Systems

User Guide FOX515 System Specification (R8)

Copyright and Confidentiality: All rights of this document remain with

ABB has taken reasonable care in compiling this document, however

User Guide FOX515 System Specification (R8)

Common features system specification

System control and management functions

Performance control and diagnostic functions

Compatibility with other FOX equipment

User Guide FOX515 System Specification (R8)

Cross connections and delays

Protection switching restoration times

EMC/ESD and safety

Ambient and dependability

Dimensions and weight

User Guide FOX515 System Specification (R8)

Dimensions and weight

User Guide FOX515 System Specification (R8)

Precautions and safety

Precautions and safety User Guide

Release Note FOX / UCST

User Guide FOX515 System Specification (R8)

ABB Switzerland Ltd

+41 844 845 845 (Call Center)

User Guide FOX515 System Specification (R8)

User Guide FOX515 System Specification (R8)

Common features system specification

Common features system

- Traffic signal types

data and voice

- Special traffic processing

- NGN Access Gateway

- Broadband Access Aggregation

- Bit-rates of traffic signals

data and voice services

Common features system specification

User Guide FOX515 System Specification (R8)

- Any mixture of above

P0-nc (n = 1 ... 31)

User Guide FOX515 System Specification (R8)

Common features system specification

ATM traffic functions

VC-4 / ATM cells

- Traffic control functions

UPC (Usage Parameter Control)

- Egress traffic (from ABUS)

Support of remote ATM services

- Remote services (third party IAD/CPE)

- Number of IMA groups

Common features system specification

User Guide FOX515 System Specification (R8)

- Cell frame length

1 service class (selectable)

32, 64, 128, 256 cells

- Maximum Differential Delay between links

- Number of CES interfaces

- Synchronisation of PDH traffic

physical section (optical)

User Guide FOX515 System Specification (R8)