Datasheet SC5104
Datasheet SC5104
FEATURES
DIP-16-300-2.54
* CMOS technology
* High noise immunity
* Wide range of voltage: Vcc=2.2 ~ 4.0 V
* LED indicator
* Transmits signal of maximum 8 channels
* 2 bits custom code options available
* Key-in oscillation, reduce static current dissipation.
* 38kHz carrier transmits output.
ORDERING INFORMATION
Device
Package
SC5104
DIP-16-300-2.54
SC5104S
SOP-16-225-1.27
APPLICATIONS
* Fan remote control
* Air cleaner
* Humidifier
* Heater
BLOCK DIAGRAM
REV:1.2
2009.05.05
Page 1 of 8
SC5104
Symbol
Ratings
Unit
Supply Voltage
VDD
-0.3~6.0
Input/Output Voltage
VIN
VSS -0.3V~VDD+0.3V
Power Dissipation
PD
500
mW
Operating Temperature
Topr
-10 ~ +70
Storage Temperature
Tstg
-40~+125
Symbol
VDD
Test conditions
-no load, oscillation is stopped,
ISB
C1=C2=0
no load, oscillation is stopped,
C1=C2=1
Min.
Typ.
Max.
Unit
2.0
3.0
4.0
--
0.1
--
--
1.8
--
IOH
VOH=2.7V
--
0.74
--
mA
IOL
VOL=0.3V
--
-2.5
--
mA
VIH
--
0.7VDD
--
VDD
VIL
--
--
0.3VDD
IOH
VOH=2.7V
--
2.5
10
mA
IOL
VOL=0.3V
--
-1.0
--
mA
--
455
--
kHz
Oscillation Frequency
fOSC
Rc
VIN=0V
--
--
Ri
VIN=0V
--
250
--
PIN CONFIGURATION
16 VDD
C2
15 DOUT
K1
14 LED
K2
K3
K4
11 K8
K5
10 K7
VSS
SC5104
C1
13 OSCO
12 OSCI
K6
REV:1.2
2009.05.05
Page 2 of 8
SC5104
PIN DESCRIPTION
Pin no.
Symbol
I/O
Descriptions
Custom Code Option: Built In Pull-Up Resistor, Grounding Denote 1,
1~2
C1, C2
3~7
K1~K5
VSS
--
9~11
K6~K8
12
OSCI
13
OSCO
14
LED
15
DOUT
16
VDD
--
Floating Denote 0.
FUNCTION DESCRIPTIONS
1.
In static mode, key inputs K1~K8 are set as high level through pull-up resistor and there is no current flows in
circuit. When one key is pressed, corresponding code is transmitted.
2.
In static mode, C1 and C2 are internal pulled as high level. Four different customer code combination are
available by the two bits. For these two bits, 1 indicates corresponding pin is grounded while 0 indicates
floating or connected to VDD.
3.
Code format
4Logic 0: 1/4T high level, 3/4T low level; Logic 1: 3/4T high level, 1/4T Low level.
5Code cyclic time T=1.6879ms
6Intern\val between two frame: 4T
REV:1.2
2009.05.05
Page 3 of 8
SC5104
4.
Data out
Data code is output at Dout. When one key is pressed, high level is output at pin LED and data (four frames at
least) is output at Dout after 32ms delay. Data is continuously output if the key is kept pressed and there is 4
code interval between frames.
5.
Oscillator
Internal oscillator integrates advanced key-press start power saving function. The oscillator is in sleep mode
when there is no key pressed and there is no current; it only works when key is pressed. This is for power saving.
455KHz oscillator is connected to pins OSCI and OSCO for using.
6.
Instruction code
D0
D1
D2
D3
D4
D5
D6
K1
K2
K3
K4
K5
K6
K7
K8
00
REV:1.2
2009.05.05
Page 4 of 8
SC5104
REV:1.2
2009.05.05
Page 5 of 8
SC5104
PACKAGE OUTLINE
DIP-16-300-2.54
UNIT: mm
SOP-16-225-1.27
UNIT: mm
1.27
0.4
5.720.25
3.90.3
6.00.4
1.80MAX
0.2
+0.05
-0.02
10.150.25
REV:1.2
2009.05.05
Page 6 of 8
SC5104
Disclaimer:
Silan reserves the right to make changes to the information herein for the improvement of the design and performance
without further notice!
All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products
in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety
standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products
could cause loss of body injury or damage to property.
REV:1.2
2009.05.05
Page 7 of 8