SLOS039D − JULY 1989 − REVISED AUGUST 2009

D Single-Supply Operation: DW PACKAGE

Input Voltage Range Extends to Ground, (TOP VIEW)
and Output Swings to Ground While
1OUT 1 16 4OUT
Sinking Current
1IN− 2 15 4IN−
D Input Offset Voltage 300 µV Max at 25°C for 1IN+ 3 14 4IN+
LT1014
VCC+ 4 13 VCC−/GND
D Offset Voltage Temperature Coefficient 2IN+ 5 12 3IN+
2.5 µV/°C Max for LT1014 2IN− 6 11 3IN−
D Input Offset Current 1.5 nA Max at 25°C for 2OUT 7 10 3OUT
LT1014 NC 8 9 NC
D High Gain 1.2 V/µV Min (RL = 2 kΩ), 0.5 V/µV
Min (RL = 600 Ω) for LT1014 J OR N PACKAGE
D Low Supply Current 2.2 mA Max at 25°C for (TOP VIEW)
LT 1014
D Low Peak-to-Peak Noise Voltage 1OUT 1 14 4OUT
0.55 µV Typ 1IN− 2 13 4IN−
1IN+ 3 12 4IN+
D Low Current Noise 0.07 pA/√Hz Typ
VCC+ VCC−
4 11
2IN+ 5 10 3IN+
description
2IN− 6 9 3IN−
The LT1014, LT1014A, and LT1014D are quad 2OUT 7 8 3OUT
precision operational amplifiers with 14-pin
industry-standard configuration. They feature low
FK PACKAGE
offset-voltage temperature coefficient, high gain, (TOP VIEW)
low supply current, and low noise.

1OUT

4OUT
1IN−

4IN−
NC
The LT1014, LT1014A, and LT1014D can be
operated with both dual ±
   
 
    The common-mode input voltage 3 2 1 20 19
1IN+ 4 18 4IN+
range includes ground, and the output voltage can NC 5 17 NC
also swing to within a few milivolts of ground. VCC+ 6 16 VCC−/GND
Crossover distortion is eliminated. NC 15 NC
7
The LT1014C and LT1014D are characterized for 2IN+ 8 14 3IN+
9 10 11 12 13
operation from 0°C to 70°C. The LT1014I and
LT1014DI are characterized for operation from
2IN−

3IN−
2OUT
NC
3OUT

−40°C to 105°C. The LT1014M, LT1014AM and

LT1014DM are characterized for operation over
NC − No internal connection
the full military temperature range of −55°C to
125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.


    !   "#$ %!& Copyright  2009, Texas Instruments Incorporated
%   "! "! '! !  !( !
%% )*& % "!+ %!  !!$* $%!
!+  $$ "!!&

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

AVAILABLE OPTIONS{
PACKAGED DEVICES}
VIO max SMALL CHIP CERAMIC PLASTIC
TA
AT 25°C OUTLINE CARRIER DIP DIP
(DW)§ (FK) (J) (N)
300 µV — — — LT1014CN
0°C to 70°C
800 µV LT1014DDW — — LT1014DN
300 µV — — — LT1014IN
−40°C to 105°C
800 µV LT1014DIDW — — LT1014DIN
180 µV — LT1014AMFK LT1014AMJ —
−55°C
−55 C to 125
125°C
C 300 µV — LT1014MFK LT1014MJ LT1014MN
800 µV LT1014DMDW — — LT1014DMN
† For the most current package and ordering information, see the Package Option Addendum at the end
of this document, or see the TI web site at www.ti.com.
‡ Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
§ The DW package is available taped and reeled. Add the suffix R to the device type
(e.g., LT1014DDWR).

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 V CC+

9 kΩ 9 kΩ 1.6 kΩ 1.6 kΩ 1.6 kΩ 100 Ω 1 kΩ 800 Ω

Q5 Q36

Q6 Q13 Q16 Q14 Q15 Q32

Q35
Q30
schematic (each amplifier)

Q3 J1
Q25 Q37
Q4
Q33

3.9 kΩ Q26 Q41

2.4 kΩ
Q1 Q27
21 pF 2.5 pF 14 kΩ
18 Ω
400 Ω Q38
IN− OUT

POST OFFICE BOX 655303

Q21 Q2 Q28

400 Ω Q39
IN+
Q12 Q18 4 pF Q31 Q40
Q22
Q29

• DALLAS, TEXAS 75265

Q10
Q11 Q34
Q19 2 kΩ
Q8
10 pF

Q9 Q7 Q17 Q23
10 pF

Q20
Q24
5 kΩ 5 kΩ 2 kΩ 2 kΩ 42 kΩ 600 Ω
75 pF

1.3 kΩ 30 Ω

VCC−

Component values are nominal.

SLOS039D − JULY 1989 − REVISED AUGUST 2009





    

 

3





    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage (see Note 1): VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V
Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V
Input voltage range, VI (any input) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC− − 5 V to VCC+
Duration of short-circuit current at (or below) TA = 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: LT1014C, LT1014D . . . . . . . . . . . . . . . . . . . . . . . . . . . −0°C to 70°C
LT1014I, LT1014DI . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 105°C
LT1014M, LT1014AM, LT1014DM . . . . . . . . . . . . . −55°C to 125°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. Differential voltages are at the noninverting input with respect to the inverting input.
3. The output may be shorted to either supply.
DISSIPATION RATING TABLE
TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 105°C TA = 125°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING POWER RATING
DW 1025 mV 8.2 mW/°C 656 mW 369 mW 205 mW
FK 1375 mV 11.0 mW/°C 880 mW 495 mW 275 mW
J 1375 mV 11.0 mW/°C 880 mW 495 mW 275 mW
N 1150 mV 9.2 mW/°C 736 mW 414 mW 230 mW

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
LT1014C LT1014D
PARAMETER TEST CONDITIONS TA† UNIT
MIN TYP‡ MAX MIN TYP‡ MAX
25°C 60 300 200 800
VIO Input offset voltage RS = 50 Ω µV
V
Full range 550 1000

aV Temperature coeficient
IO Full range 0.4 2.5 0.7 5 µV/°C
of input offset voltage
Long-term drift
25°C 0.5 0.5 µV/mo
of input offset voltage
25°C 0.15 1.5 0.15 1.5
IIO Input offset current nA
Full range 2.8 2.8
25°C −12 −30 −12 −30
IIB Input bias current nA
Full range −38 −38
−15 −15.3 −15 −15.3
25°C to to to to
Common-mode 13.5 13.8 13.5 13.8
VICR V
input voltage range
−15 −15
Full range
to 13 to 13
Maximum peak output 25°C ±12.5 ±14 ±12.5 ±14
VOM RL = 2 kΩ V
voltage swing Full range ±12 ±12
VO = ±10 V, RL = 600 Ω 25°C 0.5 2 0.5 2
Large-signal differential
AVD 25°C 1.2 8 1.2 8 V/µV
voltage amplification VO = ±10 V, RL = 2 kΩ
Full range 0.7 0.7
Common-mode VIC = −15 V to 13.5 V 25°C 97 117 97 117
CMRR dB
rejection ratio VIC = −15 V to 13 V Full range 94 94
Supply-voltage 25°C 100 117 100 117
kSVR rejection ratio CC = ±2 V to ±18 V
VCC± dB
(∆VCC/∆VIO) Full range 97 97
Channel separation VO = ±10 V, RL = 2 kΩ 25°C 120 137 120 137 dB
Differential
rid 25°C 70 300 70 300 MΩ
input resistance
Common-mode
ric 25°C 4 4 GΩ
input resistance
Supply current 25°C 0.35 0.55 0.35 0.55
ICC mA
per amplifier Full range 0.6 0.6
† Full range is 0°C to 70°C.
‡ All typical values are at TA = 25°C.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC± = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0

(unless otherwise noted)
LT1014C LT1014D
PARAMETER TEST CONDITIONS TA† UNIT
MIN TYP MAX MIN TYP MAX
25°C 90 450 250 950
VIO Input offset voltage RS = 50 Ω µV
V
Full range 570 1200
25°C 0.2 2 0.2 2
IIO Input offset current nA
Full range 6 6
25°C −15 −50 −15 −50
IIB Input bias current nA
Full range −90 −90
0 −0.3 0 −0.3
Common-mode 25°C
VICR to 3.5 to 3.8 to 3.5 to 3.8 V
input voltage range
Full range 0 to 3 0 to 3
Output low, No load 25°C 15 25 15 25
Output low, 25°C 5 10 5 10
mV
RL = 600 Ω to GND Full range 13 13
Maximum peak output
VOM Output low, Isink = 1 mA 25°C 220 350 220 350
voltage swing
Output high, No load 25°C 4 4.4 4 4.4
Output high, 25°C 3.4 4 3.4 4 V
RL = 600 Ω to GND Full range 3.2 3.2
Large-signal differential VO = 5 mV to 4 V,
AVD 25°C 1 1 V/µV
voltage amplification RL = 500 Ω
Supply current 25°C 0.3 0.5 0.3 0.5
ICC mA
per amplifier Full range 0.55 0.55
† Full range is 0°C to 70°C.

operating characteristics, VCC± = ±15 V, VIC = 0, TA = 25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
f = 10 Hz 24
Vn Equivalent input noise voltage nV/√Hz
f = 1 kHz 22
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
In Equivalent input noise current f = 10 Hz 0.07 pA/√Hz

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
LT1014I LT1014DI
PARAMETER TEST CONDITIONS TA† UNIT
MIN TYP‡ MAX MIN TYP‡ MAX
25°C 60 300 200 800
VIO Input offset voltage RS = 50 Ω µV
V
Full range 550 1000

aV Temperature coeficient
IO Full range 0.4 2.5 0.7 5 µV/°C
of input offset voltage
Long-term drift
25°C 0.5 0.5 µV/mo
of input offset voltage
25°C 0.15 1.5 0.15 1.5
IIO Input offset current nA
Full range 2.8 2.8
25°C −12 −30 −12 −30
IIB Input bias current nA
Full range −38 −38
−15 −15.3 −15 −15.3
25°C to to to to
Common-mode 13.5 13.8 13.5 13.8
VICR V
input voltage range
−15 −15
Full range
to 13 to 13
Maximum peak 25°C ±12.5 ±14 ±12.5 ±14
VOM RL = 2 kΩ V
output voltage swing Full range ±12 ±12
VO = ±10 V, RL = 600 Ω 25°C 0.5 2 0.5 2
Large-signal differential
AVD 25°C 1.2 8 1.2 8 V/µV
voltage amplification VO = ±10 V, RL = 2 kΩ
Full range 0.7 0.7
Common-mode 25°C 97 117 97 117
CMRR VIC = −15 V to 13.5 V dB
rejection ratio Full range 94 94
Supply-voltage 25°C 100 117 100 117
kSVR rejection ratio CC = ±2 V to ±18 V
VCC± dB
(∆VCC/∆VIO) Full range 97 97
Channel separation VO = ±10 V, RL = 2 kΩ 25°C 120 137 120 137 dB
Differential
rid 25°C 70 300 70 300 MΩ
input resistance
Common-mode
ric 25°C 4 4 GΩ
input resistance
Supply current 25°C 0.35 0.55 0.35 0.55
ICC mA
per amplifier Full range 0.6 0.6
† Full range is −40°C to 105°C.
‡ All typical values are at TA = 25°C.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0

(unless otherwise noted)
LT1014I LT1014DI
PARAMETER TEST CONDITIONS TA† UNIT
MIN TYP MAX MIN TYP MAX
25°C 90 450 250 950
VIO Input offset voltage RS = 50 Ω µV
V
Full range 570 1200
25°C 0.2 2 0.2 2
IIO Input offset current nA
Full range 6 6
25°C −15 −50 −15 −50
IIB Input bias current nA
Full range −90 −90
0 −0.3 0 −0.3
Common-mode 25°C
VICR to 3.5 to 3.8 to 3.5 to 3.8 V
input voltage range
Full range 0 to 3 0 to 3
Output low, No load 25°C 15 25 15 25
Output low, 25°C 5 10 5 10
mV
RL = 600 Ω to GND Full range 13 13
Maximum peak
VOM Output low, Isink = 1 mA 25°C 220 350 220 350
output voltage swing
Output high, No load 25°C 4 4.4 4 4.4
Output high, 25°C 3.4 4 3.4 4 V
RL = 600 Ω to GND Full range 3.2 3.2
Large-signal differential VO = 5 mV to 4 V,
AVD 25°C 1 1 V/µV
voltage amplification RL = 500 Ω
Supply current 25°C 0.3 0.5 0.3 0.5
ICC mA
per amplifier Full range 0.55 0.55
† Full range is −40°C to 105°C.

operating characteristics, VCC+ = ±15 V, VIC = 0, TA = 25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
f = 10 Hz 24
Vn Equivalent input noise voltage nV/√Hz
f = 1 kHz 22
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
In Equivalent input noise current f = 10 Hz 0.07 pA/√Hz

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
TEST LT1014M LT1014AM LT1014DM
PARAMETER TA† UNIT
CONDITIONS MIN TYP‡ MAX MIN TYP‡ MAX MIN TYP‡ MAX
Input offset 25°C 60 300 60 180 200 800
VIO RS = 50 Ω µV
V
voltage Full range 550 350 1000
Temperature
aV coefficient of
Full range 0.5 2.5 0.5 2 0.5 2.5 µV/°C
IO
input offset
voltage
Long-term drift
of input offset 25°C 0.5 0.5 0.5 µV/mo
voltage
Input offset 25°C 0.15 1.5 0.15 0.8 0.15 1.5
IIO nA
current Full range 5 2.8 5
Input bias 25°C −12 −30 −12 −20 −12 −30
IIB nA
current Full range −45 −30 −45
−15 −15.3 −15 −15.3 −15 −15.3
Common-mode 25°C to to to to to to
VICR input voltage 13.5 13.8 13.5 13.8 13.5 13.8 V
range −14.9 −14.9 −14.9
Full range
to 13 to 13 to 13
Maximum peak 25°C ±12.5 ±14 ±13 ±14 ±12.5 ±14
VOM output voltage RL = 2 kΩ V
swing Full range ±11.5 ±12 ±11.5
VO = ±10 V,
Large-signal 25°C 0.5 2 0.8 2.2 0.5 2
RL = 600 Ω
differential
AVD V/ V
V/µV
voltage VO = ±10 V, 25°C 1.2 8 1.5 8 1.2 8
amplification RL = 2 kΩ Full range 0.25 0.4 0.25
VIC = −15 V to
25°C 97 117 100 117 97 117
Common-mode 13.5 V
CMRR dB
rejection ratio VIC = −14.9 V
Full range 94 96 94
to 13 V
Supply-voltage 25°C 100 117 103 117 100 117
VCC± = ±2 V to
kSVR rejection ratio dB
±18 V Full range 97 100 97
(∆VCC/∆VIO)
Channel VO = ±10 V,
25°C 120 137 123 137 120 137 dB
separation RL = 2 kΩ
Differential input
rid 25°C 70 300 100 300 70 300 MΩ
resistance
Common-mode
ric 25°C 4 4 4 GΩ
input resistance
Supply current 25°C 0.35 0.55 0.35 0.50 0.35 0.55
ICC mA
per amplifier Full range 0.7 0.6 0.7
† Full range is −55°C to 125°C.
‡ All typical values are at TA = 25°C.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0

(unless otherwise noted)
TEST LT1014M LT1014AM LT1014DM
PARAMETER TA† UNIT
CONDITIONS MIN TYP MAX MIN TYP MAX MIN TYP MAX
25°C 90 450 90 280 250 950
RS = 50Ω
Input Full range 400 1500 400 960 800 2000
VIO µV
offset voltage RS = 50Ω,
125°C 200 750 200 480 560 1200
VIC = 0.1 V
Input 25°C 0.2 2 0.2 1.3 0.2 2
IIO
offset current Full range 10 7 10
nA
Input 25°C −15 −50 −15 −35 −15 −50
IIB
bias current Full range −120 −90 −120
0 −0.3 0 −0.3 0 −0.3
Common- 25°C
to 3.5 to 3.8 to 3.5 to 3.8 to 3.5 to 3.8
VICR mode input V
voltage range 0.1 0.1 0.1
Full range
to 3 to 3 to 3
Output low,
25°C 15 25 15 25 15 25
No load
Output low, 25°C 5 10 5 10 5 10
RL = 600Ω to mV
GND Full range 18 15 18
Maximum Output low,
VOM 25°C 220 350 220 350 220 350
peak output Isink = 1 mA
voltage swing
Output high,
25°C 4 4.4 4 4.4 4 4.4
No load
Output high, 25°C 3.4 4 3.4 4 3.4 4 V
RL = 600Ω to
Full range 3.1 3.2 3.1
GND
Large-signal
differential VO = 5 mV to 4 V,
AVD 25°C 1 1 1 V/µV
voltage RL = 500Ω
amplification
Supply current 25°C 0.3 0.5 0.3 0.45 0.3 0.5
ICC mA
per amplifier Full range 0.65 0.55 0.65
† Full range is −55°C to 125°C.

operating characteristics, VCC± = ±15 V, VIC = 0, TA = 25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
f = 10 Hz 24
Vn Equivalent input noise voltage nV/√Hz
f = 1 kHz 22
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
In Equivalent input noise current f = 10 Hz 0.07 pA/√Hz

10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS

Table of Graphs
FIGURE
VIO Input offset voltage vs Balanced source resistance 1
VIO Input offset voltage vs Free-air temperature 2
∆VIO Warm-Up Change in input offset voltage vs Elapsed time 3
IIO Input offset current vs Free-air temperature 4
IIB Input bias current vs Free-air temperature 5
VIC Common-mode input voltage vs Input bias current 6
vs Load resistance 7, 8
AVD Differential voltage amplification
vs Frequency 9, 10
Channel separation vs Frequency 11
Output saturation voltage vs Free-air temperature 12
CMRR Common-mode rejection ratio vs Frequency 13
kSVR Supply-voltage rejection ratio vs Frequency 14
ICC Supply current vs Free-air temperature 15
IOS Short-circuit output current vs Elapsed time 16
Vn Equivalent input noise voltage vs Frequency 17
In Equivalent input noise current vs Frequency 17
VN(PP) Peak-to-peak input noise voltage vs Time 18
Pulse response (small signal) vs Time 19, 21
Pulse response (large signal) vs Time 20, 22, 23
Phase shift vs Frequency 9

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS†

LT1014 INPUT OFFSET VOLTAGE

INPUT OFFSET VOLTAGE OF REPRESENTATIVE UNITS
vs vs
BALANCED SOURCE RESISTANCE FREE-AIR TEMPERATURE
10 250
TA = 25°C VCC± = ±15 V
200

VIO − Input Offset Voltage − µ V

150
VIO − Input Offset Voltage − mV

100
1
50

0
VCC± = 5 V
VCC− = 0 −50
0.1 −100

RS −150
VCC± = ±15 V −
−200
+
RS −250
0.01
1k 3k 10 k 30 k 100 k 300 k 1 M 3 M 10 M −50 −25 0 25 50 75 100 125

Rs − Source Resistance − Ω TA − Free-Air Temperature − °C

Figure 1 Figure 2

WARM-UP CHANGE IN INPUT OFFSET VOLTAGE INPUT OFFSET CURRENT

vs vs
ELAPSED TIME FREE-AIR TEMPERATURE
5 1
VCC± = ±15 V VIC = 0
∆V IO − Change in Input Offset Votlage − µ V

TA = 25°C

4 0.8
I IO − Input Offset Current − nA

3 0.6

2 0.4 VCC± = ±2.5 V

N Package VCC+ = 5 V, VCC− = 0

1 0.2
J Package
VCC± = ±15 V

0 0
0 1 2 3 4 5 −50 −25 0 25 50 75 100 125
t − Time After Power-On − min TA − Free-Air Temperature − °C

Figure 3 Figure 4
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS†

INPUT BIAS CURRENT COMMON-MODE INPUT VOLTAGE

vs vs
FREE-AIR TEMPERATURE INPUT BIAS CURRENT
−30 15 5
VIC = 0 TA = 25°C

VIC − Common-Mode Input Voltage − V

VIC − Common-Mode Input Voltage − V

−25 10 4
I IB − Input Bias Current − nA

−20 5 3
VCC± = ±15 V
VCC = 5 V, VCC− = 0 VCC+ = 5 V
(Left Scale)
−15 0 VCC− = 0 2
(Right Scale)
VCC± = ±2.5 V
−10 VCC± = ±15 V −5 1

−5 −10 0

0 −15 −1
−50 −25 0 25 50 75 100 125 0 −5 −10 −15 −20 −25 −30
TA − Free-Air Temperature − °C IIB − Input Bias Current − nA

Figure 5 Figure 6

DIFFERENTIAL VOLTAGE AMPLIFICATION DIFFERENTIAL VOLTAGE AMPLIFICATION

vs vs
LOAD RESISTANCE LOAD RESISTANCE
10 10
A VD − Differential Voltage Amplivication − V/µ V

A VD − Differential Voltage Amplivication − V/µ V

VCC± = ±15 V VCC+ = 5 V, VCC− = 0

VO = ±10 V VO = 20 mV to 3.5 V
4 TA = 25°C 4

TA = −55°C TA = −55°C

1 1
TA = 25°C
TA = 125°C

0.4 0.4 TA = 125°C

0.1 0.1
100 400 1k 4k 10 k 100 400 1k 4k 10 k
RL − Load Resistance − Ω RL − Load Resistance − Ω

Figure 7 Figure 8

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS†

DIFFERENTIAL VOLTAGE AMPLIFICATION

AND PHASE SHIFT DIFFERENTIAL VOLTAGE AMPLIFICATION
vs vs
FREQUENCY FREQUENCY
80° 140
VIC = 0 CL = 100 pF

A VD − Differential Voltage Amplivication − dB

A VD − Differential Voltage Amplivication − dB

CL = 100 pF 100° TA = 25°C

20 120
TA = 25°C
VCC± = ±15 V
120° 100
AVD VCC + = 5 V
VCC+ = 5 V VCC± = ±15 V

φ − Phase Shift
10 140° VCC − = 0
VCC− = 0 80

160° 60

VCC+ = 5 V
0 VCC− = 0 180° 40

200° 20
VCC± = ±15 V
−10 220° 0

240° −20
0.01 0.3 1 3 10 0.01 0.1 1 10 100 1 k 10 k 100 k 1 M 10 M
f − Frequency − MHz f − Frequency − Hz
Figure 9 Figure 10

CHANNEL SEPARATION OUTPUT SATURATION VOLTAGE

vs vs
FREQUENCY FREE-AIR TEMPERATURE
160 10
VCC± = ±15 V VCC+ = 5 V to 30 V
VI(PP) = 20 V to 5 kHz VCC− = 0
RL = 2 kΩ
140 TA = 25°C
Output Saturation Voltage − V

Isink = 10 mA
Channel Separation − dB

Limited by 1
Thermal RL = 100 Ω Isink = 5 mA
120
Interaction
Isink = 1 mA

100 RL = 1 kΩ
Isink = 100 µA
Limited by 0.1
Pin-to-Pin
80 Capacitance
Isink = 10 µA

Isink = 0
60 0.01
10 100 1k 10 k 100 k 1M −50 −25 0 25 50 75 100 125
f − Frequency − Hz TA − Free-Air Temperature − °C

Figure 11 Figure 12

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS†

COMMON-MODE REJECTION RATIO SUPPLY-VOLTAGE REJECTION RATIO

vs vs
FREQUENCY FREQUENCY
120 140
TA = 25°C VCC± = ± 15 V

K SVR − Supply-Voltage Rejection Ratio − dB

CMRR − Common-Mode Rejection Ratio − dB

TA = 25°C
120
100
VCC± = ±15 V
100 Positive
80 VCC+ = 5 V
Supply
VCC− = 0
80 Negative
Supply
60
60

40
40

20
20

0 0
10 100 1k 10 k 100 k 1M 0.1 1 10 100 1k 10 k 100 k 1M
f − Frequency − Hz f − Frequency − Hz

Figure 13 Figure 14

SUPPLY CURRENT SHORT-CIRCUIT OUTPUT CURRENT

vs vs
FREE-AIR TEMPERATURE ELAPSED TIME
460 40
TA = −55°C VCC± = ±15 V
I OS − Short-Circuit Output Current − mA
I CC − Supply Current Per Amplifier −µ A

30 TA = 25°C
420
20 TA = 125°C

380 10

VCC± = ±15 V 0

340 TA = 125°C
−10

−20 TA = 25°C
300 VCC+ = 5 V
VCC− = 0 TA = −55°C
−30

260 −40
−50 −25 0 25 50 75 100 125 0 1 2 3
TA − Free-Air Temperature − °C t − Time − min

Figure 15 Figure 16

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS

EQUIVALENT INPUT NOISE VOLTAGE PEAK-TO-PEAK INPUT NOISE VOLTAGE

AND EQUIVALENT INPUT NOISE CURRENT OVER A 10-SECOND PERIOD
vs vs
FREQUENCY TIME
1000 1000 2000
VCC± = ±2 V to ±18 V
Vn − Equivalent Input Noise Voltage − fA/ Hz

VCC± = ±2 V to ±18 V

I n − Equivalent Input Noise Current −fA/ Hz

TA = 25°C f = 0.1 Hz to 10 Hz
TA = 25°C
1600

V N(PP) − Noise Voltage − nV

300 300
In

1200

100 100

800

Vn
30 30 400

1/f Corner = 2 Hz

10 10 0
1 10 100 1k 0 2 4 6 8 10
f − Frequency − Hz t − Time − s

Figure 17 Figure 18

VOLTAGE-FOLLOWER SMALL-SIGNAL VOLTAGE-FOLLOWER LARGE-SIGNAL

PULSE RESPONSE PULSE RESPONSE
vs vs
TIME TIME
80 6
VCC± = ±15 V VCC+ = 5 V
AV = 1 VCC− = 0
60 5
TA = 25°C VI = 0 to 4 V
RL = 0
40 4 AV = 1
V O − Output Voltage − mV

V O − Output Voltage − V

TA = 25°C

20 3

0 2

−20 1

−40 0

−60 −1

−80 −2
0 2 4 6 8 10 12 14 0 10 20 30 40 50 60 70
t − Time − µs t − Time − µs

Figure 19 Figure 20

16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

TYPICAL CHARACTERISTICS

VOLTAGE-FOLLOWER SMALL-SIGNAL VOLTAGE-FOLLOWER LARGE-SIGNAL

PULSE RESPONSE PULSE RESPONSE
vs vs
TIME TIME
160 6
VCC+ = 5 V VCC+ = 5 V
140 VCC− = 0 VCC− = 0
VI = 0 to 100 mV 5
VI = 0 to 4 V
RL = 600 Ω to GND RL = 4.7 kΩ to 5 V
120
AV = 1
V O − Output Voltage − mV

V O − Output Voltage − mV
AV = 1
TA = 25°C TA = 25°C
100
3
80
2
60
1
40

20 0

0 −1

−20 −2
0 20 40 60 80 100 120 140 0 10 20 30 40 50 60 70
t − Time − µs t − Time − µs

Figure 21 Figure 22

VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
6
VCC+ = 5 V
VCC− = 0
5
VI = 0 to 4 V
RL = 0
4 AV = 1
V O − Output Voltage − V

TA = 25°C
3

−1

−2
0 10 20 30 40 50 60 70
t − Time − µs

Figure 23

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION

single-supply operation
The LT1014 is fully specified for single-supply operation (VCC− = 0). The common-mode input voltage range
includes ground, and the output swings within a few millivolts of ground.
Furthermore, the LT1014 has specific circuitry that addresses the difficulties of single-supply operation, both
at the input and at the output. At the input, the driving signal can fall below 0 V, either inadvertently or on a
transient basis. If the input is more than a few hundred millivolts below ground, the LT1014 is designed to deal
with the following two problems that can occur:
1. On many other operational amplifiers, when the input is more than a diode drop below ground, unlimited
current flows from the substrate (VCC− terminal) to the input, which can destroy the unit. On the LT1014,
the 400-Ω resistors in series with the input (see schematic) protect the device even when the input is 5 V
below ground.
2. When the input is more than 400 mV below ground (at TA = 25°C), the input stage of similar type operational
amplifiers saturates, and phase reversal occurs at the output. This can cause lockup in servo systems.
Because of unique phase-reversal protection circuitry (Q21, Q22, Q27, and Q28), the LT1014 outputs do
not reverse, even when the inputs are at −1.5 V (see Figure 24).
However, this phase-reversal protection circuitry does not function when the other operational amplifier on the
LT1014 is driven hard into negative saturation at the output. Phase-reversal protection does not work on an
amplifier:
D When 4’s output is in negative saturation (the outputs of 2 and 3 have no effect)
D When 3’s output is in negative saturation (the outputs of 1 and 4 have no effect)
D When 2’s output is in negative saturation (the outputs of 1 and 4 have no effect)
D When 1’s output is in negative saturation (the outputs of 2 and 3 have no effect)
At the output, other single-supply designs either cannot swing to within 600 mV of ground or cannot sink more
than a few microproamperes while swinging to ground. The all-npn output stage of the LT1014 maintains its low
output resistance and high gain characteristics until the output is saturated. In dual-supply operations, the output
stage is free of crossover distortion.

5 5 5
V I(PP) − Input Voltage − V

4
V O − Output Voltage − V

V O − Output Voltage − V

4 4
3
3 3
2
2 2
1

0 1 1

−1 0 0

−2 −1 −1
(a) VI(PP) = −1.5 V to 4.5 V (b) Output Phase Reversal (c) No Phase Reversal
Exhibited by LM358 Exhibited by LT1014

Figure 24. Voltage-Follower Response

With Input Exceeding the Negative Common-Mode Input Voltage Range

18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION

comparator applications
The single-supply operation of the LT1014 can be used as a precision comparator with TTL-compatible output.
In systems using both operational amplifiers and comparators, the LT1014 can perform multiple duties (see
Figures 25 and 26).

5 5
VCC+ = 5 V
V O − Output Voltage − V

V O − Output Voltage − V
4 VCC− = 0
4
TA = 25°C
10 mV 5 mV 2 mV
3 3

2 2
Overdrive 10 mV 5 mV 2 mV
1 1
Overdrive
0 0

Input Voltage
Differential
Input Voltage
Differential

VCC+ = 5 V 100 mV
100 mV
VCC− = 0
TA = 25°C

0 50 100 150 200 250 300 350 400 450 0 50 100 150 200 250 300 350 400 450
t − Time − µs t − Time − µs

Figure 25. Low-to-High-Level Output Response Figure 26. High-to-Low-Level Output Response
for Various Input Overdrives for Various Input Overdrives

low-supply operation
The minimum supply voltage for proper operation of the LT1014 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290 µA; therefore, power dissipation is only 1 mW per amplifier.

offset voltage and noise testing

Figure 30 shows the test circuit for measuring input offset voltage and its temperature coefficient. This circuit
with supply voltages increased to ±20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1014 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise-voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION
0.1 µF

100 kΩ

10 Ω
+
2 kΩ
LT1014 + 22 µF
4.3 kΩ Oscilloscope
− 4.7 µF LT1001
Rin = 1 MΩ
AVD = 50,000
− 2.2 µF
100 kΩ

110 kΩ
24.3 kΩ
0.1 µF

NOTE A: All capacitor values are for nonpolarized capacitors only.

Figure 27. 0.1-Hz to 10-Hz Peak-to-Peak Noise Test Circuit

10 kΩ

10 Mن 10 Mن
ƪVno2 * (820 nV)2ƫ
1ń2
+
100 Ω LT1014 Vn In +
10 Mن 10 Mن 40 MW 100
−

† Metal-film resistor

Figure 28. Noise-Current Test Circuit and Formula

50 Ω
(see Note A)

15 V

+
100 Ω
LT1014 VO = 1000 VIO
(see Note A)
−
50 Ω
(see Note A) −15 V

NOTE A: Resistors must have low thermoelectric potential.

Figure 29. Test Circuit for VIO and αVIO

20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION
5V

Q3
2N2905

820 Ω
Q1
2N2905

T1‡ 1N4002 (4)

10 µF 10 µF
+ +
68 Ω
SN74HC04 (6)

0.002 µF
10 kΩ 820 Ω Q2
2N2905
10 kΩ 10 kΩ
0.33 µF 100 kΩ
Q4
2N2222 5V
10 Ω†
±
2 kΩ
1/4 10 kن
100 Ω†
LT1014 4 kن 20-mA
+ Trim
100 pF 1 kΩ
10 kن 4-mA 80 ن 4-mA to 20-mA OUT
Trim
± To Load
4.3 kΩ 1/4 2.2 kΩ Max
5V
LT1014
+
LT1004
1.2 V
IN
0 to 4 V

† 1% film resistor. Match 10-kΩ resistors 0.05%.

‡ T1 = PICO-31080

Figure 30. 5-V Powered, 4-mA to 20-mA Current-Loop Transmitter With 12-Bit Accuracy

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 21






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION

0.1 Ω T1 1N4002 (4)

10 µF
5V + +
100 kΩ 1/4
To − LT1014
1/4
Inverter −
LT1014
Driver 68 kن 4-mA to 20-mA OUT
+
Fully Floating
10 kن

4.3 k٠4 kن 301 ن

5V
2 kΩ 1 kΩ
LT1004 4-mA 20-mA
1.2 V Trim Trim
IN
0 to 4 V
† 1% film resistor

Figure 31. Fully Floating Modification to 4-mA to 20-mA Current-Loop Transmitter With 8-Bit Accuracy

5V
1/2 LTC1043
6 5 5 8
IN+ +
1/4 7
2 OUT A
1 µF LT1014
1 µF 6
3 −
4 R2
18 15
IN−

R1

1/2 LTC1043
7 8 3
IN+ +
1/4 1
11 OUT B
1 µF LT1014
1 µF 2
12 −
R2
13 14
IN−

0.01 µF R1

NOTE A: VIO = 150 µV, AVD = (R1/R2) + 1, CMRR = 120 dB, VICR = 0 to 5 V

Figure 32. 5-V Single-Supply Dual Instrumentation Amplifier

22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265






    

 
SLOS039D − JULY 1989 − REVISED AUGUST 2009

APPLICATION INFORMATION

10
+
8 To Input
200 kن LT1014
9 Cable Shields
−
5V 2
−
‡ 1 10 kΩ†
LT1014
20 k٠3 10 kن
IN− + 5V
10 kΩ 13 4
‡ −
RG (2 kΩ Typ) 14
LT1014 OUT
200 kΩ 12
+
1 µF 11
10 kΩ
6
‡ −
7
LT1014
20 kΩ 5
IN+ 10 kن 10 kن
+
‡

5V
† † 1% film resistor. Match 10-kΩ resistors 0.05%.
‡ For high source impedances, use 2N2222 as diodes (with collector connected to base).
NOTE A: AVD = (400,000/RG) + 1

Figure 33. 5-V Powered Precision Instrumentation Amplifier

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 23

 PACKAGE OPTION ADDENDUM

www.ti.com 15-Oct-2009

PACKAGING INFORMATION

Orderable Device Status (1) Package Package Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Type Drawing Qty
5962-89677012A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
5962-8967701CA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
5962-89677022A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
5962-8967702CA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
LT1014AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
LT1014AMJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
LT1014AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
LT1014CN ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014CNE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014DDW ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DDWE4 ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DDWR ACTIVE SOIC DW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DDWRE4 ACTIVE SOIC DW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DIDW ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DIDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DIDWR ACTIVE SOIC DW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DIDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DIN ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014DINE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014DMDW ACTIVE SOIC DW 16 40 TBD CU NIPDAU Level-1-220C-UNLIM
LT1014DMDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
LT1014DN ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014DNE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
LT1014IN OBSOLETE PDIP N 14 TBD Call TI Call TI
LT1014MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
LT1014MJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
LT1014MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
(1)
The marketing status values are defined as follows:

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 15-Oct-2009

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF LT1014D :

• Enhanced Product: LT1014D-EP
NOTE: Qualified Version Definitions:
• Enhanced Product - Supports Defense, Aerospace and Medical Applications

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 7-Jul-2009

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 (mm) B0 (mm) K0 (mm) P1 W Pin1
Type Drawing Diameter Width (mm) (mm) Quadrant
(mm) W1 (mm)
LT1014DDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1
LT1014DIDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 7-Jul-2009

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LT1014DDWR SOIC DW 16 2000 346.0 346.0 33.0
LT1014DIDWR SOIC DW 16 2000 346.0 346.0 33.0

Pack Materials-Page 2
 MECHANICAL DATA

MLCC006B – OCTOBER 1996

FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER

28 TERMINAL SHOWN

NO. OF A B
18 17 16 15 14 13 12
TERMINALS
** MIN MAX MIN MAX

0.342 0.358 0.307 0.358

19 11 20
(8,69) (9,09) (7,80) (9,09)
20 10 0.442 0.458 0.406 0.458
28
(11,23) (11,63) (10,31) (11,63)
21 9
B SQ 0.640 0.660 0.495 0.560
22 8 44
(16,26) (16,76) (12,58) (14,22)
A SQ
23 7 0.739 0.761 0.495 0.560
52
(18,78) (19,32) (12,58) (14,22)
24 6
0.938 0.962 0.850 0.858
68
(23,83) (24,43) (21,6) (21,8)
25 5
1.141 1.165 1.047 1.063
84
(28,99) (29,59) (26,6) (27,0)
26 27 28 1 2 3 4

0.020 (0,51) 0.080 (2,03)

0.010 (0,25) 0.064 (1,63)

0.020 (0,51)
0.010 (0,25)

0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)

0.028 (0,71) 0.045 (1,14)

0.022 (0,54) 0.035 (0,89)
0.050 (1,27)

4040140 / D 10/96

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DLP® Products www.dlp.com Broadband www.ti.com/broadband
DSP dsp.ti.com Digital Control www.ti.com/digitalcontrol
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Military www.ti.com/military
Logic logic.ti.com Optical Networking www.ti.com/opticalnetwork
Power Mgmt power.ti.com Security www.ti.com/security
Microcontrollers microcontroller.ti.com Telephony www.ti.com/telephony
RFID www.ti-rfid.com Video & Imaging www.ti.com/video
RF/IF and ZigBee® Solutions www.ti.com/lprf Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated