Introduction and Basic Concepts: Heat and Mass Transfer

Heat and Mass Transfer: Fundamentals & Applications
Fourth Edition
Yunus A. Cengel, Afshin J. Ghajar
McGraw-Hill, 2011
Chapter 1
INTRODUCTION AND BASIC
CONCEPTS
Copyright 2011 The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
1-1 THERMODYNAMICS AND HEAT TRANSFER

Heat: The form of energy that can be transferred from one
system to another as a result of temperature difference.
Thermodynamics is concerned with the amount of heat
transfer as a system undergoes a process from one
equilibrium state to another.
Heat Transfer deals with the determination of the rates of
such energy transfers as well as variation of temperature.
The transfer of energy as heat is always from the highertemperature medium to the lower-temperature one.
Heat transfer stops when the two mediums reach the same
temperature.
Heat can be transferred in three different modes:
conduction, convection, radiation
2
Application Areas of Heat Transfer
Energy Transfer
Energy can be transferred to or from a given mass
by two mechanisms:
when
is constant:
heat transfer (J) and work.

Heat transfer rate: (J/s, W) The amount of heat
transferred per unit time.
Heat flux: (W/m2) The rate of heat transfer per unit
area normal to the direction of heat transfer.
Power: The work done per unit time.
Figure 1.14
1-5 HEAT TRANSFER MECHANISMS
Heat as the form of energy that can be transferred from one

system to another as a result of temperature difference.
A thermodynamic analysis is concerned with the amount of heat
transfer as a system undergoes a process from one equilibrium
state to another.
The science that deals with the determination of the rates of such
energy transfers is the heat transfer.
The transfer of energy as heat is always from the highertemperature medium to the lower-temperature one, and heat
transfer stops when the two mediums reach the same temperature.
Heat can be transferred in three basic modes:
conduction
convection
radiation
All modes of heat transfer require the existence of a temperature
difference.
1-6 CONDUCTION
Conduction: The transfer of energy from the more
energetic particles of a substance to the adjacent less
energetic ones as a result of interactions between the
particles.
In gases and liquids, conduction is due to the
collisions and diffusion of the molecules during their
random motion.
In solids, it is due to the combination of vibrations of
the molecules in a lattice and the energy transport by
free electrons.
The rate of heat conduction through a plane layer is
proportional to the temperature difference across the
layer and the heat transfer area, but is inversely
proportional to the thickness of the layer.
Heat conduction
through a large plane
wall of thickness x
and area A.
9
When x 0
Fouriers law of
heat conduction
Thermal conductivity, k: A measure of the ability of

a material to conduct heat.
Temperature gradient dT/dx: The slope of the
temperature curve on a T-x diagram.
A = 1 m2
Heat is conducted in the direction of decreasing

temperature, and the temperature gradient becomes
negative when temperature decreases with
increasing x. The negative sign in the equation
ensures that heat transfer in the positive x direction
is a positive quantity.
A = 1 m2
In heat conduction
analysis, A represents
the area normal to the
direction of heat
transfer.
The rate of heat conduction

through a solid is directly
proportional to its thermal
10
conductivity.
Figure 1.27
Thermal
Conductivity
Thermal conductivity:
The rate of heat transfer
through a unit thickness
of the material per unit
area per unit
temperature difference.
The thermal conductivity
of a material is a
measure of the ability of
the material to conduct
heat.
A high value for thermal
conductivity indicates
that the material is a
good heat conductor,
and a low value indicates
that the material is a
poor heat conductor or
insulator.
A simple experimental setup

to determine the thermal
conductivity of a material by
measuring the terminal
temperature.
13
The range of
thermal
conductivity of
various
materials at
room
temperature.
14
The thermal conductivities of gases such

as air vary by a factor of 104 from those of
pure metals such as copper.
Pure crystals and metals have the
highest thermal conductivities, and gases
and insulating materials the lowest.
The mechanisms of heat

conduction in different
phases of a substance.
15
The variation of
the thermal
conductivity of
various solids,
liquids, and gases
with temperature.
16
Thermal Diffusivity
cp Specific heat, J/kg C: Heat capacity
per unit mass
cp Heat capacity, J/m3C: Heat capacity
per unit volume
Thermal diffusivity, m2/s: Represents
how fast heat diffuses through a material
A material that has a high thermal

conductivity or a low heat capacity will
obviously have a large thermal diffusivity.
The larger the thermal diffusivity, the faster
the propagation of heat into the medium.
A small value of thermal diffusivity means
that heat is mostly absorbed by the
material and a small amount of heat is
conducted further.
17
Figure 1.32
Figure 1.33
1-7 CONVECTION
Convection: The mode of
energy transfer between a
solid surface and the
adjacent liquid or gas that is
in motion, and it involves
the combined effects of
conduction and fluid motion.
The faster the fluid motion,
the greater the convection
heat transfer.
In the absence of any bulk
fluid motion, heat transfer
between a solid surface and
the adjacent fluid is by pure
conduction.
Heat transfer from a hot surface to air

by convection.
21
Forced convection: If
the fluid is forced to flow
over the surface by
external means such as
a fan, pump, or the wind.
Natural (or free)
convection: If the fluid
motion is caused by
buoyancy forces that are
induced by density
differences due to the
variation of temperature
in the fluid.
The cooling of a boiled egg by

forced and natural convection.
Heat transfer processes that involve change of phase of a fluid are also
considered to be convection because of the fluid motion induced
during the process, such as the rise of the vapor bubbles during boiling
or the fall of the liquid droplets during condensation.
22
Newtons law of cooling

h
As
Ts
T
convection heat transfer coefficient, W/m2 C

the surface area through which convection heat transfer takes place
the surface temperature
the temperature of the fluid sufficiently far from the surface.
The convection heat transfer

coefficient h is not a property
of the fluid.
It is an experimentally
determined parameter
whose value depends on all
the variables influencing
convection such as
- the surface geometry
- the nature of fluid motion
- the properties of the fluid
- the bulk fluid velocity
23
Figure 1.37
1-8 RADIATION
Radiation: The energy emitted by matter in the form of electromagnetic
waves (or photons) as a result of the changes in the electronic
configurations of the atoms or molecules.
Unlike conduction and convection, the transfer of heat by radiation does
not require the presence of an intervening medium.
In fact, heat transfer by radiation is fastest (at the speed of light) and it
suffers no attenuation in a vacuum. This is how the energy of the sun
reaches the earth.
In heat transfer studies we are interested in thermal radiation, which is
the form of radiation emitted by bodies because of their temperature.
All bodies at a temperature above absolute zero emit thermal radiation.
Radiation is a volumetric phenomenon, and all solids, liquids, and
gases emit, absorb, or transmit radiation to varying degrees.
However, radiation is usually considered to be a surface phenomenon
for solids.
26
StefanBoltzmann law
= 5.670 10-8 W/m2 K4 StefanBoltzmann constant
Blackbody: The idealized surface that emits radiation at the maximum rate.
Radiation emitted
by real surfaces
Emissivity : A measure of how closely
a surface approximates a blackbody for
which = 1 of the surface. 0 1.
Blackbody radiation represents the maximum

amount of radiation that can be emitted from
a surface at a specified temperature.
27
Absorptivity : The fraction of the radiation energy incident on a

surface that is absorbed by the surface. 0 1
A blackbody absorbs the entire radiation incident on it ( = 1).
Kirchhoffs law: The emissivity and the absorptivity of a surface at
a given temperature and wavelength are equal.
The absorption of radiation incident on

an opaque surface of absorptivity .
28
Net radiation heat transfer:

The difference between the
rates of radiation emitted by the
surface and the radiation
absorbed.
The determination of the net
rate of heat transfer by radiation
between two surfaces is a
complicated matter since it
depends on
When a surface is completely enclosed by a

much larger (or black) surface at temperature
Tsurr separated by a gas (such as air) that
does not intervene with radiation, the net rate
of radiation heat transfer between these
two surfaces is given by
the properties of the surfaces

their orientation relative to
each other
the interaction of the medium
between the surfaces with
radiation
Radiation is usually
significant relative to
conduction or natural
convection, but
negligible relative to
forced convection.
Radiation heat transfer between a

surface and the surfaces surrounding it.
29
When radiation and convection occur

simultaneously between a surface and a gas:
Combined heat transfer coefficient hcombined

Includes the effects of both convection and radiation
30
Figure 1.41
Table 1-6
1-9 SIMULTANEOUS HEAT

TRANSFER MECHANISMS
Heat transfer is only by conduction in opaque solids,
but by conduction and radiation in semitransparent
solids.
A solid may involve conduction and radiation but not
convection. A solid may involve convection and/or
radiation on its surfaces exposed to a fluid or other
surfaces.
Heat transfer is by conduction and possibly by
radiation in a still fluid (no bulk fluid motion) and by
convection and radiation in a flowing fluid.
In the absence of radiation, heat transfer through a
fluid is either by conduction or convection, depending
on the presence of any bulk fluid motion.
Convection = Conduction + Fluid motion
Although there are three mechanisms of
Heat transfer through a vacuum is by radiation.
heat transfer, a medium may involve
only two of them simultaneously.
Most gases between two solid surfaces
do not interfere with radiation.
Liquids are usually strong absorbers of
33
radiation.
Figure 1.43
Table 1-6
Figure 1.44
Figure 1.45
Figure 1.47

Introduction and Basic Concepts: Heat and Mass Transfer

Uploaded by

Copyright:

Available Formats

Introduction and Basic Concepts: Heat and Mass Transfer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Introduction and Basic Concepts: Heat and Mass Transfer

Uploaded by

Copyright:

Available Formats

Heat and Mass Transfer: Fundamentals & Applications

1-1 THERMODYNAMICS AND HEAT TRANSFER

Application Areas of Heat Transfer

heat transfer (J) and work.

1-5 HEAT TRANSFER MECHANISMS

Heat as the form of energy that can be transferred from one

Thermal conductivity, k: A measure of the ability of

Heat is conducted in the direction of decreasing

The rate of heat conduction

A simple experimental setup

The thermal conductivities of gases such

The mechanisms of heat

A material that has a high thermal

Heat transfer from a hot surface to air

The cooling of a boiled egg by

Newtons law of cooling

convection heat transfer coefficient, W/m2 C

The convection heat transfer

Blackbody radiation represents the maximum

Absorptivity : The fraction of the radiation energy incident on a

The absorption of radiation incident on

Net radiation heat transfer:

When a surface is completely enclosed by a

the properties of the surfaces

Radiation heat transfer between a

When radiation and convection occur

Combined heat transfer coefficient hcombined

1-9 SIMULTANEOUS HEAT

You might also like