La5744

Ordering number : ENA0717C
Monolithic Linear IC
Separately-Excited Step-Down
LA5744
Switching Regulator
(Variable Type)
Overview
The LA5744 is a separately-excited step-down switching regulator (variable type).
Functions
High efficiency.
Time-base generator (300kHz) incorporated.
Current limiter incorporated.
Thermal shutdown circuit incorporated.
Soft start circuit incorporated.
Specifications
Maximum Ratings at Ta = 25C
Parameter
Input voltage
Symbol
Conditions
Ratings
VIN
Maximum output current

SW pin application reverse voltage
Allowable power dissipation
Unit
30
IO max
VSW
-1
1.75
Pd max1
No heat sink
Pd max2
Infinite heat sink
7.5
Operating temperature
Topr
-30 to +125
Storage temperature
Tstg
-40 to +150
Junction temperature
Tj max
150
* Specified circuit board : 76.1114.31.6mm3 : Copper foil ratio 60% FR4
Recommended Operating Conditions at Ta = 25C

Parameter
Input voltage range
Symbol
VIN
Conditions
Ratings
Unit
4.5 to 28
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
52307 MS PC 20070522-S00004 / 42507 MS PC / 31407 MS PC / 30707 MS PC 20070215-S00001 No.A0717-1/5
LA5744
Electrical Characteristics at Ta = 25C, VO = 5V
Parameter
Symbol
Ratings
Conditions
min
Reference voltage
VOS
VIN = 15V, IO = 1.0A
VIN = 15V, IO = 1.0A
Efficiency
Switching frequency
typ
1.20
Unit
max
1.23
1.26
83
VIN = 15V, IO = 1.0A
300
360
kHz
Line regulation
VOLINE
VIN = 8 to 20V, IO = 1.0A
40
100
mV
Load regulation
VOLOAD
VIN = 20V, IO = 0.5 to 1.5A
10
30
VO/Ta
Output voltage temperature
240
0.5
Designed target value. *
mV
mV/C
coefficient
Ripple attenuation factor
RREJ
Current limiter operating voltage
f = 100 to 120Hz
IS
Thermal shutdown operating
45
VIN = 15V
dB
3.1
TSD
165
TSD
15
temperature
Thermal shutdown Hysteresis
width
* Design target value : No measurement made.
Package Dimensions
unit : mm (typ)
3343
Pd max -- Ta
4.5
10.4MAX
10.0
1.3
21.7
23.0
15.3
(8.8)
15.0
2.7
3.6
0.9
2.7
1
0.8
(1.6)
8.0
7.5
1001001.5mm3
6.0
5.6
50501.5mm3
4.0
3.3
2.0
1.75
1.7
0.4
4.5
Infinite heat sink jc=5C
Al heat
sink
mounting
torque
39Ncm
silicone
grease
applied
30301.5mm3
No heat sink
0
-30 -20
Allowable power dissipation, Pd max -- W
10.0
20
40
60
80
100
Ambient temperature, Ta -- C
120
140
160
MSG07021
8.4
SANYO : 220-5HK
Pin Assignment
(1) VIN (2) SWOUT (3) GND (4) VOS (5) SS
No.A0717-2/5
LA5744
Block Diagram
VIN 1
2 SWOUT
Constant
current
circuit
Reg.
OCP
Reset
OSC
Drive
Comp.
TSD
4 VOS
Amp.
ON/OFF Comp.
0.4V
VREF
SS
GND
Application Circuit Example

L1
22H
VIN
SWOUT
LA5744
C2
390F
D1
SBD
C1
470F
/50V
VOS
SS
GND
R2
R1
C3
1F
Notes :
1. C3 is for the soft start function. Delete C3 and keep the SS pin open when the soft start function is not necessary.
2. In some cases, the output may not turn on if power is applied when a load is connected. If this is a problem, increase the value of
the inductor.
No.A0717-3/5
LA5744
Protection Circuit Functional Descriptions
1. Overcurrent protection function
The overcurrent protection function detects, on a cycle-by-cycle basis, the output transistor current and turns off that
output transistor current if it exceeds 3.1A.
Limit current
Inductor current
SWOUT voltage
2. Short circuit protection function

This IC prevents the current from increasing when the outputs are shorted by setting the switching frequency to 30kHz
if the VOS pin voltage falls below 0.8V.
Note 3 : If the soft start function is not used, the IC will start up with the overcurrent protection function operating. At this
time, the switching frequency will be cut in half. This means that the switching frequency will be 15kHz at
startup.
Note 4 : Since the switching frequency becomes 30kHz when the VOS pin voltage falls under 0.8V, the current capacity is
reduced. If a load is applied with the VOS pin voltage over 0.8V, the inductance value operates at 22H. If a load
is to be applied when this voltage is under 0.8V, the inductance value must be increased.
Description of Functional Settings

1. Calculation equation to set the output voltage
This IC controls the switching output so that the VOS pin voltage becomes 1.23V (typ).
The equation to set the output voltage is as follows :
R2
VO = 1+
1.23V(typ)
R1
The VOS pin has the inrush current of 1A (typ). Therefore, the error becomes larger when R1 and R2 resistance
values are large.
2. Startup Delay Function
The output voltage rises when the internal voltage reaches 0.4V (typical). Until that point, a capacitor is charged from
an internal 10A (typical) constant-current supply. The startup delay time can be calculated as shown below
Example : Assume a 1F capacitor is used.
Td =
C V 1F 0.4
=
= 40 ms
i
10A
No.A0717-4/5
LA5744
Timing Chart
VIN voltage
30kHz
300kHz
SWOUT voltage
1.23V
0.8V
VOS voltage
0V
Td
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of May, 2007. Specifications and information herein are subject
to change without notice.
PS No.A0717-5/5
This datasheet has been downloaded from:

www.EEworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn
All Datasheets Cannot Be Modified Without Permission

Copyright Each Manufacturing Company

La5744

Uploaded by

Copyright:

Available Formats

La5744

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

La5744

Uploaded by

Copyright:

Available Formats

Ordering number : ENA0717C

Maximum output current

Infinite heat sink

* Specified circuit board : 76.1114.31.6mm3 : Copper foil ratio 60% FR4

Recommended Operating Conditions at Ta = 25C

52307 MS PC 20070522-S00004 / 42507 MS PC / 31407 MS PC / 30707 MS PC 20070215-S00001 No.A0717-1/5

VIN = 15V, IO = 1.0A

VIN = 15V, IO = 1.0A

VIN = 15V, IO = 1.0A

VIN = 8 to 20V, IO = 1.0A

VIN = 20V, IO = 0.5 to 1.5A

Output voltage temperature

Designed target value. *

Current limiter operating voltage

Thermal shutdown operating

Designed target value. *

Designed target value. *

Infinite heat sink jc=5C

Allowable power dissipation, Pd max -- W

Application Circuit Example

2. Short circuit protection function

Description of Functional Settings

This datasheet has been downloaded from:

All Datasheets Cannot Be Modified Without Permission

You might also like