ETPETQEN

Transducer ETP 30, ETQ 30
DATA SHEET - N00312/4
For active and reactive power
Characteristics
Active power measuring in balanced and unbalanced singlephase or three-phase mains. Power measuring for sinusoidal
signals.
Output signal with or without suppressed zero.
Galvanic isolation between input and output and auxiliary
power supply
Reduced size for mounting space saving.
Case type housing for fixing with screws or in din-rail
Output with load divider (optional).
Application
Conversion of the active and reactive power of single-phase and

three-phase mains into a direct current or voltage signal, which is
independent on the load.
Page 1/5
August 2003
Characteristic curves
Functioning
The transducers ETP-30 and ETQ-30 are fully electronic

instruments. The electrical power is calculated as follows:
That means: The instantaneous voltage and current values are

multiplied between each other and integrated in the time interval of
0T.
Examples of zero-displacement.
Power
direction
Unidirectional
The transforming units (1) attenuate the voltage and current input
signals, condition them to the multiply module (2) and establish a
galvanic isolation between the input and output signals
The multiplier (2) uses the TDM (time-division-multiplication)
principle working with an insignificant deviation from the above
mentioned equation. The result is a voltage signal proportional to be
measured power. The amplifier (3) filters this signal and converts it
into a direct current or voltage signal. The power supply (4) feeds
auxiliary power to all intern circuits with galvanic isolation from the
power net by means of an own transformer. The output module (5)
transmits 180 displaced pulses via two transmission channels in a
frequency, which is proportional to the input signal.
Bi-directional
Io
IrtdO
A
=
=
=
A/B
Characteris
tics
Measuring
Field (kW)
Output
(mA)
Zerodisplacement
A
C
F
A/B
A/B
E
D
0....100
0....100
20..100
-100..0...+100
-20....0...+100
-50....0....+100
-75....0....+50
0...20
4...20
0...20
-20...0...+20
-4...0...+20
0...20
4...20
no
yes
yes
no
no
yes
yes
Output current between 0...IrtdO.

Rated output current.
Unidirectional measuring for input without zerodisplacement and with constant inclination.
Bi-directional measuring for input without zerodisplacement and with constant inclination.
Unidirectional measuring for output with suppressed
zero.
Bi-directional measuring for output with suppressed
zero.
Bi-directional measuring for input with zerodisplacement.
Unidirectional measuring for expanded measuring
field.
Technical data (NBR 8145)

Input
Rated voltage
Current
Signal limit
Calibration
factor (cf)
Zero
displacement
Consumption
Rated frequency
Overload
Ground voltage
0..110/220/380/500V
0..1//5 A (other on consult)
UrtdI = 10...660V
IrtdI = 0,5...5 A
0,5...1,5 (others on consult)
The scale end value has to be calculated with a
factor between 0,5...1,5 times the value of the
apparent power. The apparent power (S) is
calculated using the value of the primary winding
of the transformers:
S = U x I (single phase circuit)
S = U x I x 3 (three phase circuit)
cf = P or Q = wanted power (scale end)
S
apparent power
max. 75%
voltage input: 1mA
current input: 0,15VA
50;60:400 Hz 10%
(others on consult)
permanently: 1,5 x UrtdI ; 2 x IrtdI
briefly: 4 x UrtdI/1s; 50 x IrtdI/1s
maximum: 250 A/1s
660V max. (IEC 348)
Output
Unidirectional
measuring
Bi-directional
measuring
Signal limit
Load limit
Residual ripple
Output with load
divider (optional)
0...1/5/10/20mA, 4...20mA (others on consult)

-5...0...+5mA
-10..0..+10mA max. zero displacement 75%
-20...0...+20mA
4....20mA max. zero displacement 75%
(others on consult)
Unidirectional measuring: 1...20mA
1...10V ; Rc 500
Bidirectional measuring: 1... 20 mA
1 10V ; Rc 500
maximum:
1,5 IrtdO,
25V; Rc = infinite
Rc =
15.000(mV)
max output signal (mA)
0,5% (peak to peak)
To calculate Rc use 7.500mV instead of
15.000mV, the results will br the same
for both outputs.
Page 2/5
August 2003
Power supply
a) 2060Vac/Vdc
b) 85265Vac/90300Vdc
consumption: 4W
Influence magnitudes
0,5%(normal) or 0,25% (optional)
Error limit
Reference
conditions
Input
Frequency
Form factor:
Auxiliary power
supply:
Power factor
II = 0...IrtdI;
UI = 0...UrtdI
frtd 2%
1,111
UAX 2%
c o s = 1 (active power)
s e n = 1 (reactive power)
0,5RC max.
Load:
Ambient
temperature:
25C 2K
Heat up time:
20 min.
Additional error above
1,2IrtdI or UrtdI
0,2%
Linearity deviation
0,2% (included in error limit)
Load
0,05% RC = 0....RC max.
(included in error limit)
Temperature
0,2% /10 K;
rated temperature 25C
Auxiliary power supply
0,05% within the permitted
tolerance range for the supply voltage
Response time
200 ms
External magnetic
interference
0,5% for field intensity of
0,4 kA/m
Radio frequency
interference
0,5% between 27...460MHz
at a distance of 1m; power 1 W
Crest factor
4 for alternating not sinusoidal
electrical magnitude
Electrical test
Test voltage:
UAX = 2060Vca/Vcc = 1,5kV/1 min. 60Hz
between auxiliary power supply and others
Test voltage:
UAX = 85265Vca/90300Vcc = 2,5kV/1 min. 60Hz
Between auxiliary power supply and others
Peak and transient
protection
5kV; 1,2/50 Uo; 0,5Wo
High frequency
interference
2,5kV; 1MHz; 400 pulses / 1s

Construction and mounting

Type
Electrical
connection
Protection class
(NBR6146)
Weight
Base and cover of plastic

Surface mounting with two screws M4, or using
DIN rail.
Frontal terminals for eye and fork type cable
shoes
IP 50 in housing
IP 20 at the connection terminals
0,7 kg
Climatic conditions
Operation temperature
Functioning temperature
Transport and storage temp.
Relative humidity
-20...+60C
-25...+70C
-40...+80C
75% of annual average with light
condensation (others on consult)
Mechanical test
Impact
Vibration
acceleration 30g during 11ms

acceleration 2g frequency 5..150Hz
Notes:
Umin = 50V for single-phase circuit power or equilibrated threephase circuit with a simulated phase.
Frequency deviation = 0,6% max. for active power measuring in
single-phase circuit or reactive power measuring in equilibrated
three-phase circuit with a simulated phase.
Unidirectional measuring related to the end value of the output
signal. Bi-directional measuring related to the end value of the
biggest signal range.
Response times below 200 ms result in bigger residual ripple.
Electrical Connections
13 14
UAX
Uax
O1
O2
=
=
=
+ _ + _
61 62 63 64
O1
Page 3/5
August 2003
Input without PT
Case
Housing
Fastening
O2
Auxiliary power supply

Current or voltage output - normal
Output with load divider (double output) - optional
Notes
When using only O2 jump terminals 61 and 62
When using double output, there is no galvanic isolation
between the output signals.
Page 4/5
August 2003
Input with PT
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
Active or reactive power for single-phase AC or active

power for 4-wire 3-phase with balanced load.
Active power for 3-wire 3-phase with balanced load (ETP-30).

Active power for 3-wire 3-phase with balanced load, one phase
simulated only with (ETP-30).
Reactive power for 3-wire or 4 wire 3-phase with balanced load
only with (ETQ-30).
Active or reactive power for 3-wire 3-phase with unbalanced
load.
Active or reactive power for 4-wire 3-phase with unbalanced
load
Voltage transformer for connection diagram (a), ( c) and (d).
Voltage transformer in V circuit for connection diagram (b), (e)
and (f).
3 single-pole isolated voltage transformers for connection
diagram (b), ( e) and (f)
3-phase transformer for connection diagram (b), ( e) and (f).
(*) 4-wire 3-phase with unbalanced load:

Terminal connection 11 is omitted only in transducer ETQ-30 and
ETP-30 with 2 multipliers ( UL1 + UL2 + UL3 = 0).
Dimensional drawing
Dimension in mm
Additional information
The following items contain tips and cautions to be observed by the user for
a good functional performance, as well as the maintenance of the instrument
and the safety of the installations.
Cautions
Be sure the voltages and current to be connected to the instrument,

are compatible.
Loosen all connections from the instrument before removing it from
the installation.
Mounting Instructions
Observed the ambient temperature range. At the place of installation, values

for vibration, dust, dirt and humidity, which must remain between the limits,
established by the protection class of the housing and the climatic group,
specified in this data sheet, have to be observed.
For fastening on flat area use two M4 screws. For mounting on DIN rail, use
the snap-in device on the rear of the instrument.
The connections can be made with eye or fork type cable shoes.
Instructions for Use
When connections have been made, switch on the power supply and
check at the output the functioning of the transducer.
For quoting and ordering please issue your order according to the
specification text.
Example:
Transducer ETP-30
Housing:
Rated frequency:
Measuring circuit:
Input voltage and current:
Auxiliary power supply:
Calibration factor:
Output signal:
Measuring field:
Optional:
Case
60Hz
Single-phase
0...110V/ 0...5A
85265Vca/90300Vcc
0,909
4...20mADC
200..500W
Class 0,5%
Code number: N0031221221355C
Page 5/5
August 2003
Ordering information
TRANSDUCER FOR POWER, housing case
Model / Variable
ETP-30 active power
ETQ-30 reactive power
Rated Frequency
50 Hz
60 Hz
400 Hz
Others
Measuring Circuit
Single-phase
3-wire 3-phase balanced load 3 ~1 E
3-wire 3-phase unbalanced load 3 ~2 E
4-wire 3-phase unbalanced load 3N ~3 E
Input Voltage (+/- 15% )
66V
110V
220V
380V
500V
Input Current
1A
5A
Others
Power Supply
20 60Vca/Vcc
86265Vca/90300Vcc
Output Signal
0...1mADC
0...5mADC
0...10mADC
0...20mADC
4...20mADC
0...10VDC
Others(+/- 1mAdc, +/- 20mAdc, +/- 1Vdc and +/- 15Vdc)
Option
Error limit 0,25%
Output with load divider ( double output)
Others response times between 50ms and 2s
Standard (Class 0,5%)
Additional Information
Standard
Complement (Inform measuring field, TP, TC, etc)
Catalog number
-
2
4
ABB Ltda - ATLV/IE Electrical Instrumentation

Av. Dos Autonomistas, 1496 - 06020-902 - Osasco - SP
Tel: +55 11 3688-8320 / 8323 / 8347 - Fax: +55 11 3688-8322
instrumentacao@br.abb.com
1
2
3
0
1
2
4
7
1
2
3
4
5
1
2
0
12
13
1
2
3
4
5
7
0
1
2
4
5
1
C

ETPETQEN

Uploaded by

Copyright:

Available Formats

ETPETQEN

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ETPETQEN

Uploaded by

Copyright:

Available Formats

Transducer ETP 30, ETQ 30

DATA SHEET - N00312/4

For active and reactive power

Conversion of the active and reactive power of single-phase and

The transducers ETP-30 and ETQ-30 are fully electronic

That means: The instantaneous voltage and current values are

Output current between 0...IrtdO.

Transducer ETP 30, ETQ 30

DATA SHEET - N00312/4

For active and reactive power

Technical data (NBR 8145)

0...1/5/10/20mA, 4...20mA (others on consult)

0,5%(normal) or 0,25% (optional)

Transducer ETP 30, ETQ 30

Construction and mounting

Base and cover of plastic

acceleration 30g during 11ms

DATA SHEET - N00312/4

Auxiliary power supply

Transducer ETP 30, ETQ 30

DATA SHEET - N00312/4

For active and reactive power

Active or reactive power for single-phase AC or active

Active power for 3-wire 3-phase with balanced load (ETP-30).

(*) 4-wire 3-phase with unbalanced load:

Be sure the voltages and current to be connected to the instrument,

Observed the ambient temperature range. At the place of installation, values

Instructions for Use

Code number: N0031221221355C

Transducer ETP 30, ETQ 30

DATA SHEET - N00312/4

For active and reactive power

ABB Ltda - ATLV/IE Electrical Instrumentation

You might also like