Product description The digital universal measuring device PEM735 is suited for measuring and displaying electrical quantities of electricity networks. The device measures currents and voltages, energy consumption and power, and displays the individual current/voltage harmonics for assessment of the power quality in accordance with DIN EN 50160. The accuracy of active energy measurements corresponds to class 0.2 S in accordance with DIN EN 62053-22 (VDE 0418 part 3-22). The current inputs are connected via external /1 A or /5 A measuring current transformers. Typical application Continuous monitoring of the voltage quality in accordance with DIN EN 50160 PEM735
Collection of relevant data for energy management systems
High-resolution waveform recording allows analysis of power quality phenomena
Device features Class A power analyser, certified according to DIN EN 61000-4-30 Monitoring the quality of the voltage in accordance with DIN EN 50160 A ccuracy class according to IEC 62053-22: 0.2 S TFT colour display (640x480) 5.7 Modbus/RTU and Modbus/TCP 4 current inputs 5 voltage inputs 1 GB internal memory Panel mounting 144x144 Integrated web server Data export via FTP: comtrade, PQDIF Flicker measurement Detection and recording of transients (40 s)
Description of function Sampling rate of the measuring channels: 25.6 kHz Calculation of the total harmonic distortion THDU/THDI: harmonics up to the 63rd harmonic Individual current/voltage harmonics Password protection History memory for minimum and maximum values of current, voltage, energy, power rating etc. for each month. Inputs and outputs: 6 digital outputs, 8 digital inputs (1 kHz sampling rate) 24 adjustable parameter setpoints System protocol: 1024 events, setup changes, setpoint alarming, DI status changes, DO switching operations Communication: Galvanically isolated RS-485 interface (1.200 to 19.200 bit/s) Modbus/RTU protocol Modbus/TCP (10/100 MBit/s)
Sampling rate: 512 samples/cycle
Standards
F reely configurable recorders for waveform,
consumption and long-term recording
The universal measuring device for Power Quality and Energy Measurement/PEM735 was developed in accordance with the following standards: IEC 62053-22(VDE 0418 Part 3-22), DIN EN 61557-12 (VDE 0413-12), DIN EN 50160, DIN EN 61000-4-30 (VDE 0847-4-30), DIN EN 61000-4-7 (VDE 0847-4-7), DIN EN 61000-4-15 (VDE 0847-4-15)
IEC 61850
2 PEM735_D00084_00_D_XXEN/06.2014
Power Quality and Energy Measurement PEM735
Operating elements
1 PEM735 LINETRAXX
1 - Pulse LED: kWh
2 - Pulse LED: kvarh
kvarh
kWh
3 - Display 4 - " " button: Selection (in the menu) 5 - " " button: Up (in the menu) 6 - " " button: Down (in the menu)
7 - " " button: Selection (in the menu)
8 - "ENTER" button: OK 9 - "ESC" button:
ENTER
ESC
Example for system set-up
PEM7xx
PEM7xx
Ethernet Datenbank Modbus/TCP
Modbus/TCP
NSHV
L PEN
CP700
PE PAS BMS PEM5xx
PEM5xx
Modbus/TCP
RCMS
I 112
Modbus/TCP
Modbus/RTU L N PE
Modbus/ RTU
Modbus/RTU UV1
UV2
PEM3xx
Modbus/RTU
RCMS
PEM3xx
112
U I
Modbus/RTU
PEM735_D00084_00_D_XXEN/06.2014 3
Power Quality and Energy Measurement PEM735
Wiring diagram
Connection diagram voltage inputs
US
Three-phase 4-wire system (TN, TT, IT systems)
The PEM can be used in three-phase 4-wire systems, independent of the type of distribution system (TN, TT, IT system).
2 DO1+
DO1-
DO2+
DO2-
AC 400 V/230 V AC 690V/400 V
DI1
DI2
DI3
DI4
DI5
DI7
DI6
DIC
DI8
L1
NC
L1
SH D+
L4
L2
DSH
L3
DIC
RO13
DI1
RO14
DI2
RO23
DI3
RO24
DI4
RO33
DI5
RO34
DI6
RO43
DI7
RO44
NC
NC
D-
P1(RS-485)
D+
PEM Three-phase 3-wire system The PEM can be used in three-phase 3-wire systems.
Link
AC 690 V
DO1+ DO1DO2+
A1/+ Power
I32 l42
AC 400 V
10/100M Ethernet
P3
l31 l41
l22
l21
Act
LED
l11
I12
DI8
L3
Ri
P2(RS-485)
L2
DO2-
A2/-
2 L1
I12
I22
I32
I21
I11
I31
I42
L2
L3
Ri
I41 L1
PEM
L2 L3 N
5 L1
L2
L3
Connection via voltage transformers
The coupling via measuring current transformers allows the use of the measuring device in medium and high voltage systems. The transformation ration can be adjusted in the PEM735. LV / MV / HV
1 - Connection RS-485 bus
2 - Supply voltage. Power protection by a 6 A fuse, quick response. If being supplied from an IT system, both lines have to be protected by a fuse. 3 - Digital inputs 4 - Digital outputs (N/O contacts) 5 - Measuring voltage inputs
L1
6 - Connection to the system to be monitored: The measuring
leads should be protected with appropriate fuses.
Ri
7 - Connection Ethernet 8 - Relay output
4 PEM735_D00084_00_D_XXEN/06.2014
PEM
L2
L3
Power Quality and Energy Measurement PEM735
Technical data Insulation co-ordination
Interface
Measuring circuit Rated insulation voltage Overvoltage category Pollution degree Supply circuit Rated insulation voltage Overvoltage category Pollution degree
Interface/protocol Baud rate Cable length Shielded cable ((shield connected to PE on one side)
600 V III 2 300 V II 2
Supply voltage Rated supply voltage US Frequency range of US Power consumption
95250 V DC, 44440 Hz 11 VA
Measuring circuit Measuring voltage inputs UL1-N,L2-N,L3-N 400 V UL1-L2,L2-L3,L3-L1 690 V Measuring range 10 120 % Un Rated frequency 4258 Hz Internal resistance (L-N) > 500 k Measuring current inputs External measuring current transformer, should at least comply with accuracy class 0.2 S Burden n.A., internal current transformers Measuring range 0.1 120 % IN CT transformation ratio, secondary 15 A CT transformation ratio, primary 130000 A Accuracies (of measured value/of full scale value) Phase voltage UL1-N, UL2-N, UL3-N 0.1 % of the measured value. Current 0.1 % of measured value + 0.05 % of full scale value. Frequency 0.005 Hz Phase position 1 Active energy measurement acc. to DIN EN 62053-22 (VDE 0418 Part 3-22) R.m.s. voltage measurements acc. to DIN EN 61557-12 (VDE 0413-12), chapter 4.7.6 R.ms. phase current measurements acc. to DIN EN 61557-12 (VDE 0413-12), chapter 4.7.5 Frequency measurements acc. to DIN EN 61557-12 (VDE 0413-12), chapter. 4.7.4 Measurement of the harmonics acc. to DIN EN 61000-4-7 class A
2 x RS-485, Modbus/RTU 1.219.2 kbits / s 01200 m recommended: J-Y(St)Y min. 2x0.8
InterfaceEthernet Protocol FTP, Modbus/TCP, IEC 61850 Baud rate 100 MBit/s Switching elements Outputs (RO) 4 x N/O contacts Operating principle N/O operation Rated operational voltage AC 230 V DC 24 V AC 110 V DC 12 V Rated operational current 5A 5A 6A 5A Minimum contact rating 1 mA at AC/DC 10 V Inputs 8 electrically separated digital inputs Imin 2.4 mA UDI DC 24 V 2 electronic outputs (DO) max. 80 V
Imax 50 mA Environment/EMC EMC Operating temperature Climatic class acc. to DIN EN 60721 stationary use Classification of mechanical conditions acc. to IEC 60721 stationary use
DIN EN 61326-1 -25+ 55 C 3K5 3M4
Connection Connection
screw-type terminals
Other Degree of protection, installation Degree of protection, front Documentation number Weight
IP20 IP52 D00084 1100 g
PEM735_D00084_00_D_XXEN/06.2014 5
Ordering information Nominal system voltage 3(N)AC 100690 V
PEM735_D00084_00_D_XXEN / 06.2014 / pdf / Schw / Bender GmbH & Co. KG, Germany Subject to change! The specified standards take into account the current edition at the time of going to press.
