Technical Data

A Power Quality analyser and

fault recorder

Model PQI-DE
1 4 x voltage, 5 x current
1 20 kHz bandwidth
1 Residual current monitor RCM
The PQI-DE meets the requirements of IEC 61000-4-
1. Application 30:2015 Ed 3 +A1:2021 for Class A measuring instru-
ments for 100 % of the parameters.
The Power Quality Analyser and Fault Recorder PQI-DE
for low, medium and high voltage networks is the cen-
tral component of a system with which all Parameter IEC61000-4-30 Ed. 3 Class
measurement tasks in electrical networks can be
solved. Power frequency A
The PQI-DE can be used as a Power Quality Interface Magnitude of the Supply Voltage A
according to power quality standards such as
IEC 61000-2-2 / EN 50160 or to check the technical Flicker A
connection guidelines such as DIN VDE AR 4110 and
DIN VDE 4120 and many more. Due to the available Supply voltage dips and swells A
open SCADA standard interfaces such as Modbus
RTU/TCP as well as IEC 61850 with open data exchange Voltage interruptions A
format PQDIF (IEEE1159-3), the device can also be used
as a highly accurate measurement transducer for all Supply voltage unbalance A
physically defined measured variables in 3-phase sys-
tems parallel to the continuous recording of measured Voltage harmonics A
values over a very long period.
In addition to the possibility of standard evaluations, Voltage interharmonics A
the PQI-DE also has a high-speed disturbance recorder
with a recording rate of 40.96kHz/10.24kHz and a 10ms Mains signalling voltage A
TRMS effective value recorder. This allows a detailed
evaluation of grid disturbances. Measurement aggregation intervals A
The PQI-DE is equipped with a fifth current input for
continuous residual current monitoring (RCM). It is Time-clock uncertainty A
possible to freely program thresholds for alarms or
warnings. Flagging A
Modern Power Quality Analysers comply with the IEC
Transient influence quantities A
62586 standard, which describes the complete product
feature of a Power Quality Analyser. This standard The measuring device and the development are subject
defines not only the purpose of use, the EMC environ- to strict security requirements within the scope of the
ment and the environmental conditions, but also the requirements in the area of KRITIS. In relation to these,
exact measurement methods IEC 61000-4-30 Class A, in an active patch management, encrypted communica-
order to create a comparable and reliable basis for the tion standards as well as a User Rights Management
end-user. (URM) via RADIUS are available in the device! This also
According to IEC 62586, the PQI-DE is a device of class includes signed firmware updates, security logging and
PQI-A-FI-H and is therefore fully certified in external active protection against brute force attacks. All this
laboratories. Power Quality Interface – Class A – Fixed contributes to a secure operation in your IT environ-
Installed Measurement Device for Indoor operation in ment!
Harsh EMC environments

Version Aug-23
g
We take care of it.

2. Design 0 Recording of power quality incidents according to

DIN EN 50160; IEC 61000-2-2; -2-12; -2-4
The PQI-DE has been developed for measurements 0 Power buffer for voltage interruptions of up to 2
performed within public grids as well as for recording seconds
PQ data within an industrial environment up to 690V 0 Spectral analysis 2 kHz…20kHz (90 frequency bands,
(L-L) measurement voltage. Bandwidth = 200Hz) of voltages and currents
0 No moving parts (fans, hard drives etc.) according (IEC 61000-4-7)
0 CAT IV 0 Phase of voltage and current harmonics n=2..50
0 Extensive storage capability (can be extended up to 0 8 digital inputs (Triggering fault records, Recording
32 GB by the user, permitting several years record- Start / Stop,
ing without connection to database) 0 4 relay outputs for protection monitoring and
1 Optional: “IEC 61000-4-7 - 2 kHz to 20kHz” (B1) alarming
0 Frequency measurement of voltage and current 0 EDGE function - 32 freely configurable monitoring
according to IEC 61000-4-7 from 2 kHz to 20kHz. states for monitoring and triggering all measured
0 Sampling rate voltage and current 40.96kHz variables - Output as binary message or via protocol
0 Free of charge analysis software WinPQ lite (sold as
1 Optional: Residual current monitor RCM (D1)
a package)
1 Optional: "PQDIF data format" (F1) 0 Option: Analysis of the data on a database using the
0 Open data exchange format according to IEEE1159- WinPQ software package.
3 via MMS / IEC61850 (feature P2) Permanent communication and evaluation of the
data with many devices in parallel.
2.1 Characteristics of the Power-
Quality Interface PQI-DE Communication Protocols

2.1.1 Technical Data – MODBUS RTU & MODBUS TCP

0 5-inch colour display – IEC 60870-5-104 (Option P1)

0 Keypad for basic/direct device configuration – IEC 61850 (Option P2)
0 1 GB internal memory (extended up to 32 GB) – Modbus Master (Option P3)
0 IP54 in installed condition
Time synchronisation protocols
0 Input channel bandwidth 20 kHz
0 4 voltage inputs Accuracy < 0.1 % – IEEE 1344 / IRIG-B000...007
0 4 current inputs
– GPS (NMEA +PPS)
0 PE current input for the detection of differential
currents or currents of the ZEP (central grounding – DCF77
point)
0 Temperature input for Pt100 and Pt1000 sensor – NTP
0 Simultaneous processing of sampled and calculated
voltages and currents Interfaces
0 Oscilloscopic voltage and current recorder Ethernet RJ45 (10/100 Mbit)
sampling rate : 40.96 kHz / 10.24 kHz
0 Half cycle recorder : USB USB 2.0 – Type C
power frequency, RMS of voltages and currents,
voltage and current phasors, power Two RS232/RS485 switchable
recording rate : ~10 ms(50 Hz) / ~8.33 ms (60 Hz)
Dimensions
0 Powerful recorder triggering
0 Online streaming of voltages and currents LxBx 144 x 144 x 90 mm without termi-
nals
at 40.96 kHz sampling rate.
Weight 1220 g

Page 2 Design
Voltage inputs Flicker DIN EN 61000-4- Klasse F1
Feature E1 E2 E3 15:2011
Channels U1, U2, U3, UN/E/4 Dip residual voltage ±0,2 % Unom
Electrical safety 150V 300V SELV @ 10 %..100 % Unom
DIN EN 61010 CATII CAT IV Dip duration ±20 ms
600V @ 10 %..100 % Unom
CAT III Swell residual voltage ±0,2 % Unom
Input reference level PE PE PE @ 100 %..150 % Unom
Impedance -> PE 2 MΩ 10 MΩ 2 MΩ|| Swell duration ±20 ms
|| 25pF || 50pF @ 100 %..150 % Unom
25pF Interruption duration ±20 ms
Nominal input voltage 100 VAC 230 VAC 3,25V @ 1 %..100 % Unom
Un Voltage unbalance ±0,15 %
Full scale range (FSR) 0…120 0…480 0…5 VAC @ 1 %..5 % Messwert
VAC L-E VAC L-E L-E Mains signalling volt- ±5% des Messwerts
Overload, permanent 150VAC 600VAC 10VAC age @ Us = 3%..15% Unom
(< 3 kHz) ±0,15 % Un
Maximum crest factor 3 3 2,2
@ Unom @ Us = 1 %..3 % Unom

Bandwidth DC…20 kHz

Nominal power fre- 50 Hz / 60 Hz
quency fnom
Frequency range of the fn ± 15 %
fundamental 42,5..50..57,5 Hz
51,0..60..69,0 Hz
Accuracy
Fundamental, r.m.s.
U1 ≤ 150% Unom
0°C ≤ TA ≤ +45°C: ±0.1% v. Unom
-25°C ≤ TA ≤ +55°C: ±0.2% v. Unom
Fundamental, Phase
U1 ≥ 10% Unom: ±0.02°
Harmonics n = 2…50,
r.m.s. ±5.0% v. Uh
Uh ≥ 1% Unom: ±0.05% v. Unom
Uh < 1% Unom:
Harmonics n = 2…50,
Phase ±0.5°
Uh ≥ 1% Unom:
Interharmonics
n = 1…49, r.m.s.
Uih ≥ 1% Unom: ±5.0% v. Uh
Uih < 1% Unom: ±0.05% v. Unom
Power frequency ±1 mHz
@ 10 %...200 % Unom

Design Page 3

Page 3
 We take care of it.

Current inputs Accuracy

Option C30 C31 Feature 30 C31
Channels I1, I2, I3, IN/4
Fundamental, I1 ≥ 10% FSR: I1 = 1%...20% FSR:
Electrical safety 300V CAT III r.m.s. ±0.1% v. I1 ±0.5% v. I1
DIN EN 61010 I1 < 10% FSR: I1 < 1% FSR:
±0.01% v. FSR ±0.005% v. FSR
Input type potentialfrei
Fundamental, I1 ≥ 10% FSR: I1 = 1%...20% FSR:
Impedance ≤ 4mΩ
Phase ±0.1° ±0.5°
Nominal input cur- 5 AAC
rent In Harmonic n =
2…50, r.m.s.
Full scale range (FSR) 10AAC 100AAC Ih ≥ 3% Inom: ±5.0% v. Ih ±10% v. Ih
Overload capacity Ih < 3% Inom: ±0.15% v. Inom ±0.3% v. Inom
permanent 20 AAC
≤ 10s 100 AAC Harmonic n =
≤ 1s 500 AAC 2…50, Phase
Ih ≥ 3% Inom: ±0.5° ±2.0°
Waveform AC, any
Interharmonic n
Maximum crest fac- 3 30 = 1…49, r.m.s.
tor @ In
Iih ≥ 3% Inom: ±5.0% v. Iih ±10% v. Iih
Bandwidth 25Hz...20kHz Iih < 3% Inom: ±0.15% v. Inom ±0.3% v. Inom
Tightening torque 2 Nm

Page 4 Design
Feature C40 C44 C45
Full Scale Range (FSR) 0.35VAC @ 50Hz 0.50VAC ±5.6V
Impedance 1MΩ 1MΩ 1MΩ
Input type symmetrisch
Isolation basic (SELV) basic (SELV) basic (SELV)
External sensors Rogowski coil, current clamp, Hall-Sensor,
potential free potential free potential free
Differential overload, perma- 10VAC ±15V ±15V
nent
Common mode area ±15V ±15V ±15V
Bandwidth 25Hz…20kHz DC…20kHz DC…20kHz
Accuracy
Grundschwingung, r.m.s.
I1 ≥ 10% FSR: ±0.2% v. I1 ±0.1% v. I1 ±0.1% v. I1
I1 < 10% FSR: ±0.02% v. FSR ±0.01% v. FSR ±0.01% v. FSR
Grundschwingung, Phase
I1 ≥ 10% FSR: ±0.2° ±0.1° ±0.1°
Harmonische n = 2…50, r.m.s.
Ih ≥ 1% FSR: ±5.0% v. Ih ±5.0% v. Ih ±5.0% v. Ih
Ih < 1% FSR: ±0.05% v. FSR ±0.05% v. FSR ±0.05% v. FSR
Harmonische n = 2…50, Phase
Ih ≥ 1% FSR: ±1.0° ±0.5° ±0.5°
Zwischenharmonische n =
1…49, r.m.s.
Iih ≥ 1% FSR: ±5.0% v. Iih ±5.0% v. Iih ±5.0% v. Iih
Iih < 1% FSR: ±0.05% v. FSR ±0.05% v. FSR ±0.05% v. FSR

Power supply Storage of measured values

Feature H1 H2 H3 Internal memory 1024 MB
AC Nominal range [V] 100...240 - -
SD memory card 1 GB to 32 GB
AC Operating range [V] 90…264 - -

DC Nominal range [V] 120...320 24...60 48…138 Residual current monitor (RCM)
DC Operating range [V] 108…350 18…75 40…160 Nominal current 30 mA

Power ≤ 10 W ≤ 10 W ≤ 10 W Impedance 4Ω
consumption < 20 VA
Overload capacity 5 A (1 seconds)
Frequency Nominal 50...60Hz DC DC
Resolution 24bit-ADC
Frequency Operating 40...70Hz DC DC

External fuse 6A 6A 6A
characteristics B B B

Energy storage 2 sec 2 sec 2 sec

Design Page 5

Page 5
 We take care of it.

Binary outputs (BO) Electrical safety DIN 300V

4 binary outputs 3 x closer EN 61010
1 x changeover
Contact specification Binary inputs (BI)
(EN60947-4-1, -5-1) : 3 x SPST (Single Pole Single Throw) Feature M1 M2
Configuration 1 x SPDT (Single Pole Double Throw) 8 binary inputs 0 V..250 VAC 0 V...48 VDC
Nominal voltage 250VAC /VDC
Nominal current Range
6A
Nominal load AC1 1500 VA – H – Level > 35 V > 10V
Nominal load AC15, 300 VA – L – Level < 20 V < 5V
230VAC Signal frequency DC ... 70 Hz DC ... 70 Hz
Interrupting power 6/0.2/0.12 A Input resistance > 100 kΩ 6.8 kΩ
DC1, 30/110/220 V
Electrical isolation Optocoupler,
Number of switching ≥ 60·103 electrical
electrically isolated
operations AC1
Electrical safety 300V
Electrical Isolation Isolated from all internal
DIN EN 61010
potentials

Temperature input Pt 100 / Pt 1000 / KTY– (Firmware V2.2)

Contacting measurement sensor 2 wire
(software setting) 3 wire
4 wire
Update rate 1 second / 1Hz
Resolution 15 Bit
Burden 1,9 kOhm
Accuracy 0.05 % FSR

Page 6 Design
Electromagnetic Compatibility
Immunity
– IEC 61000-6-5, environment H
Emissions
– CISPR22 (EN 55022) , class A

Electrical safety
– IEC 61010-1
– IEC 61010-2-030
Protection class 1
Pollution degree 2
Overvoltage category
mains supply option :
H1 300V CAT II
H2/H3 150V CAT II
Measurement category 300V CAT IV
600V CAT III
Altitude ≤ 2000 m
IP protection class IP54 (in installed condition)

Environmental parameters Storage and transport Operation

Ambient temperature : IEC 60721-3-1 / 1K5 IEC 61010
Limit range of operation -40 ... +70°C -25 ... +45°C H1
IEC 60721-3-2 / 2K4 -25 ... +50°C H2/H3
-40 ... +70°C
Ambient temperature : IEC DIN EN 61010
Rated range of operation H1 --- -25 ... +45°C
Rated range of operation H2 /H3 -25 ... +50°C
Relative humidity: 24h average 5...95 % 5...95 %
No condensation or ice

Solar radiations --- 700 W/m2

Vibration, earth tremors IEC 60721-3-1 / 1M1 IEC 60721-3-3 / 3M1
IEC 60721-3-2 / 2M1

Design Page 7

Page 7
According to IEC61557-12, the PQI-DE corresponds to a PMD type III of class PMD -SD according to Table
2 (indirect current measurement, direct voltage measurement) for low voltage or PMD SS (indirect
current measurement, indirect voltage measurement) in climatic category K55.
Thus a marking according to IEC61557-12 is possible for the measuring device as follows:
PMD SD / K55 / 0.2
PMD SS / K55 / 0.2
Herewith the following accuracies are given:

Measured variable C40 / C44 / C30 @ 5A Current clamp Current clamp

C45 Klasse 0.5 Klasse 1
Active energy 0.2 0.2 <1 <2
Active power 0.2 0.2 <1 <2
Reactive energy <2 <2 <2 2
Reactive power <1 <1 1 <2
Apparent energy 0.2 0.2 <1 <2
Apparent power 0.2 0.2 <1 <2
Frequency < 0.02
Phase current 0.1 0.1 <1 <2
Measured IN < 0.2 < 0.2 <1 <2
Calculated IN 0.1 0.1 <1 <2
Voltage 0.1
Power factor < 0.5 < 0.5 <1 <2
Flicker 5
Dips and swells < 0.5
Voltage interruption 0.5
Voltage unbalance 0.2
Voltage harmonics 1
Voltage THD 1
Current unbalance 0.2 0.2 <1 <2
Current harmonics 1 1 <2 2
Current THD 1 1 1 1

Page 8 Design
2.1.2 Mechanical design
The PQI-DE is used as a panel-mounted device and fulfils IP54 when installed. All connections are accessible via
Phoenix terminals. Apart from the current inputs, the connections are made using plug-in terminal technology.
A TCP/IP interface (RJ 45 LAN connection) and a USB interface (type C socket) are available for communication. In
addition to the internal memory of 1 GB, the device memory can be expanded by a further 32 GB via an external
memory card. The memory card can also be used to easily read out measurement data from the instrument and
transmit it to an evaluation PC.
RCM Residual current
Powersupply monitor (RCM)

4 Voltage inputs
8 Binary Inputs

4 Binary Outputs
SD – card interface

4 current inputs
Back view PQI-DE

Temperature input
Pt 100 / Pt 1000

COM 2 COM 1
USB

Side view of PQI-DE

Design Page 9

Page 9
2.1.3 Terminal strip number PQI-DE

Terminal Designation Function Terminal cross section Stripping Torque in Nm

strip no. no. [mm²] length mm

L (+) 11 0.2 ... 2.5 10 0,5 ... 0,6

X1 Auxiliary voltage UH
L (-) 12 0.2 ... 2.5 10 0.5 ... 0.6

X1 Ground ring terminals

GND PE 13 - 0.5 ... 0.6
M4

Page 10 Design
Terminal Designation Function Terminal cross section Stripping Torque in
strip no. no. [mm²] length mm Nm
BICOM - 21 10 0.5 ... 0.6
BI1 + 22 10 0.5 ... 0.6
BI2 + 23 10 0.5 ... 0.6
solid:
BI3 + 24 10 0.5 ... 0.6
0.2 ... 1.5
X2 Binary input BI4 + 25 10 0.5 ... 0.6
flexible:
BI5 + 26 10 0.5 ... 0.6
0.2 ... 2.5
BI6 + 27 10 0.5 ... 0.6
BI7 + 28 10 0.5 ... 0.6
BI8 + 29 10 0.5 ... 0.6
Phase voltage L1 (AC) U1 L1 31 10 0.5 ... 0.6

Phase voltage L2 (AC) U2 L2 32 10 0.5 ... 0.6

X3 Phase voltage L3 (AC) U3 L3 33 0.2 ... 2.5 10 0.5 ... 0.6

Neutral point voltage U4 N/E 34

10 0.5 ... 0.6
(AC)

RTDOUT+ 41 10 0.5 ... 0.6

PT100/Pt1000/KTY RTDIN+ 42 10 0.5 ... 0.6

X4 T1 0.14 ... 0.5
Temperature input RTDIN- 43 10 0.5 ... 0.6

RTDOUT- 44 10 0.5 ... 0.6

NO 51 10 0.5 ... 0.6

R1 NC 52 10 0.5 ... 0.6

Pol 53 10 0.5 ... 0.6

NO (+) 54 solid: 10 0.5 ... 0.6

R2
0.2 ... 1.5
X5 Binary output Pol (-) 55 10 0.5 ... 0.6
flexible:
NO (+) 56 0.2 ... 2.5 10 0.5 ... 0.6
R3
Pol (-) 57 10 0.5 ... 0.6

NO (+) 58 10 0.5 ... 0.6

R4
Pol (-) 59 10 0.5 ... 0.6

I1 S1 (K) 61
Phase current L1 0.5 ... 0.8
S2 (L) 62

I2 S1 (K) 63
Phase current L2 0.5 ... 0.8
S2 (L) 64
X6
1.5 – 4 mm²
I3 S1 (K) 65
Phase current L3 0.5 ... 0.8
S2 (L) 66

I4 S1 (K) 67
Neutral / sum current 0.5 ... 0.8
S2 (L) 68

X9 + 91 solid: 10 0.5 ... 0.6

0.34... 2.5
RCM - Input I5
- 92 flexible:
0.2 ... 2.5 10 0.5 ... 0.6

Design Page 11

Page 11
2.1.4 Dimensions

Front view PQI-DE Back View PQI-DE

Panel cut-out PQI-DE Right view PQI-DE

The maximum panel thickness for PQI-DE installation is 8mm.

Page 12 Design
2.1.5 Colour display
The device's 5-inch colour display provides information about the correct connection of the measuring cables and
transmitter and shows online data of voltage, current, total harmonic distortion (THD), harmonics up to 9 kHz
power and energy. A kind of drag pointer function informs about the maximum current of the last day, the last
week, the last month and absolute since the last reset of the extreme value.
The number of Power Quality events, oscilloscope and RMS fault records for the last day, week and month appear
on the display.

The commissioning and parameterisation of the PQI-DE can be carried out very easily via the keypad and
the display of the device or via the WinPQ Lite software.

Design Page 13

Page 13
2.2 Measurement / Functions
PQI-DE complies with the automatic event detection and measurement standards, which are:
EN50160:2021/ IEC61000-2-2 / IEC61000-2-12 /IEC61000-2-4 (Class 1; 2; 3) / NRS048 / IEEE519 / IEC61000-4-30
Class A Ed 3/ IEC 61000-4-7 / IEC61000-4-15 / IEEE1159-3
Continuous Recording:
Five fixed and two variable measurement time intervals are available for continuous recording:
10/12 T (200ms), 1 sec, n*sec, 150/180 T (3sec), n*min, 10 min, 2 h

Time Interval Voltage 10/ 150/ 10 2 1 10s N* N*

12T 180T min h s s min
PQDIF ✓ ✓ ✓
Power frequency ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Extremes, standard deviation of power frequency (10s) ✓ ✓
r.m.s. values (IEC61000-4-30) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Extremes, standard deviation of T/2-values ✓
Underdeviation [%] , Overdeviation [%] (IEC61000-4-30) ✓ ✓ ✓ ✓
Harmonic subgroups n= 0..50 (IEC61000-4-7) ✓ ✓ ✓ ✓
Maximum values of 10/12 T harmonic subgroups n = 2..50 ✓
Interharmonic subgroups n=0..49 (IEC61000-4-7) ✓ ✓ ✓ ✓
Total Harmonic Distortion (THDS) (IEC61000-4-7) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Partial Weighted Harmonic Distortion (PWHD) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Unbalance, negative-/positive- sequence , sequence sign ✓ ✓ ✓ ✓ ✓ ✓ ✓
Unbalance, zero-/positive- sequence ✓ ✓ ✓ ✓ ✓ ✓ ✓
Positive-, negative-, zero sequence phasors ✓ ✓ ✓ ✓ ✓ ✓ ✓
Phasors (fundamental) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Flicker (IEC61000-4-15) ✓ ✓
Instant flicker (IEC61000-4-15) ✓ ✓
Mains signalling voltages [%] (IEC61000-4-30) ✓ ✓
Phase angle( zero crossings) of phase voltage harmonics ✓ ✓ ✓ ✓
n=2..50 to fundamental of reference voltage
Frequency bands 1..90 , 2kHz..20kHz, r.m.s. (IEC61000-4-7) ✓ ✓ ✓ ✓ ✓

Page 14 Design
Time Interval Current 10/ 150 10 2 1 N* N*
12T /180T min h s s min
PQDIF ✓ ✓
r.m.s. values ✓ ✓ ✓ ✓ ✓ ✓ ✓
Extremes of T/2-values ✓
Harmonic subgroups n= 0..50 (IEC61000-4-7) ✓ ✓ ✓ ✓
Maximum values of 10/12 T harmonic subgroups n = 2..50 ✓
Interharmonic subgroups n=0..49 (IEC61000-4-7) ✓ ✓ ✓ ✓
Total Harmonic Distortion (THDS) (IEC61000-4-7) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Total Harmonic Currents ✓ ✓ ✓ ✓ ✓ ✓ ✓
Partial Weighted Harmonic Distortion (PWHD) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Partial Odd Harmonic Currents (PHC) ✓ ✓ ✓ ✓ ✓ ✓ ✓
K-Factors ✓ ✓ ✓ ✓ ✓ ✓ ✓
Unbalance, negative-/positive- sequence , sequence sign ✓ ✓ ✓ ✓ ✓ ✓ ✓
Unbalance, zero-/positive- sequence ✓ ✓ ✓ ✓ ✓ ✓ ✓
Positive-, negative-, zero sequence phasors ✓ ✓ ✓ ✓ ✓ ✓ ✓
Phasors (fundamental) ✓ ✓ ✓ ✓ ✓ ✓ ✓
Phase angle( zero crossings) of current harmonics n=2..50 to ✓ ✓ ✓ ✓
fundamental of reference voltage
Frequency bands 1..35 , 2kHz..9kHz, r.m.s. (IEC61000-4-7) ✓ ✓ ✓ ✓ ✓

Time Interval Energy 10 2 1 N* N*

min h s s min
PQDIF ✓ ✓
Active energy, phase ✓ ✓ ✓ ✓ ✓
Active energy, total ✓ ✓ ✓ ✓ ✓
Exported active energy, phase ✓ ✓ ✓ ✓ ✓
Exported active energy, total ✓ ✓ ✓ ✓ ✓
Imported active energy, phase ✓ ✓ ✓ ✓ ✓
Imported active energy, total ✓ ✓ ✓ ✓ ✓
Reactive energy (inductive), phase ✓ ✓ ✓ ✓ ✓
Reactive energy (inductive), total ✓ ✓ ✓ ✓ ✓
Exported reactive energy (inductive), phase ✓ ✓ ✓ ✓ ✓
Exported reactive energy (inductive), total ✓ ✓ ✓ ✓ ✓
Imported reactive energy (inductive), phase ✓ ✓ ✓ ✓ ✓
Imported reactive energy (inductive), total ✓ ✓ ✓ ✓ ✓
Total apparent energies, phase& total ✓ ✓ ✓ ✓ ✓
Export apparent energies, phase & total ✓ ✓ ✓ ✓ ✓
Import apparent energies, phase & total ✓ ✓ ✓ ✓ ✓
Distortion reactive energies, phase & total ✓ ✓ ✓ ✓ ✓

Design Page 15

Page 15
Time Interval Power 10 2 1 N* N*
min h s s min
PQDIF ✓ ✓
Active power, phase ✓ ✓ ✓ ✓ ✓

Active power, total ✓ ✓ ✓ ✓ ✓

Active power extremes ✓

Reactive power, phase ✓ ✓ ✓ ✓ ✓

Reactive power, total ✓ ✓ ✓ ✓ ✓

Reactive power extremes ✓

Apparent power, phase ✓ ✓ ✓ ✓ ✓

Apparent power, total ✓ ✓ ✓ ✓ ✓

Fundamental active power, phase ✓ ✓ ✓ ✓ ✓

Fundamental active power, total ✓ ✓ ✓ ✓ ✓

Fundamental reactive power, phase ✓ ✓ ✓ ✓ ✓

Fundamental reactive power (displacement), total ✓ ✓ ✓ ✓ ✓

Fundamental apparent power, phase ✓ ✓ ✓ ✓ ✓

Phase angle of fundamental apparent power, phase ✓ ✓ ✓ ✓ ✓

Fundamental apparent power, total ✓ ✓ ✓ ✓ ✓

Phase angle of fundamental apparent power, total ✓ ✓ ✓ ✓ ✓

Reactive distortion power, phase ✓ ✓ ✓ ✓ ✓

Reactive distortion power, total ✓ ✓ ✓ ✓ ✓

Active power factors, phase, total ✓ ✓ ✓ ✓ ✓

Reactive power factors, phase, total ✓ ✓ ✓ ✓ ✓

COS + sign, phase, total ✓ ✓ ✓ ✓ ✓

SIN + sign, phase, total ✓ ✓ ✓ ✓ ✓

COS + sign of reactive distortion power, phase, total ✓ ✓ ✓ ✓ ✓

Capacitive-, inductive scaling factor of COS (-1..0..+1) : ✓ ✓ ✓ ✓ ✓

tan (L+), Phase, total on imported inductive reactive energy ✓ ✓ ✓ ✓

tan (C-),Phase, total on exported capacitive reactive energy ✓ ✓ ✓ ✓

tan (L-),Phase, total on exported inductive reactive energy ✓ ✓ ✓ ✓

tan (C+),Phase, total on imported capacitve reactive energy ✓ ✓ ✓ ✓

Triggered interval mean active power, phase

Triggered interval mean active power, total
Triggered interval mean reactive power, phase
Triggered interval mean reactive power, total

Time interval temperature & RCM 10/ 150/ 10 2 1 N* N*

12T 180T min h s s min
Temperature ✓ ✓ ✓
Residual current RCM ✓ ✓ ✓ ✓
Residual current FCM ✓ ✓ ✓ ✓
Leakage conductances, capacitances ✓ ✓ ✓ ✓

Page 16 Design
2.3 Oscilloscopic recorder
Sampling rate: 40.96 kHz / 10,24kHz / 1.024kHz
Max. Record length: 4sec (40,96kHz) / 16sec (10,24kHz) / 160sec (1.024kHz)

Quantities
3-wire system 4-wire system
phase – ground voltages phase –neutral voltages
residual voltage neutral – ground voltage
phase – phase voltages
phase currents
total current neutral current

Design Page 17

Page 17
2.4 Half cycle recorder
Recording rate: ~10 ms (50 Hz) or ~8.333 ms (60 Hz)
Max. Record length: 6 min (50 Hz) or 5 min (60 Hz)

Quantities
Power frequency
r.m.s. voltages
r.m.s. currents
Active power, phase
Reactive power, phase
Active power, total
Fundamental reactive power (displacement), total
Phase angle of fundamental apparent power, total
Voltage phasors (fundamental)
Current phasors (fundamental)
Positive-, negative-, zero sequence voltage phasors
Positive-, negative-, zero sequence current phasors

Very long recording of an grid fault with F, U, I, P and Q

Page 18 Design
2.5 Recorder triggering
trigger quantity lower upper step
RMS phase voltages (T/2) ✓ ✓ ✓

RMS phase-phase voltages (T/2) ✓ ✓ ✓

RMS residual/neutral-ground voltage (T/2) ✓ ✓

Positive sequence voltage (T/2) ✓ ✓

Negative sequence voltage (T/2) ✓

Zero sequence voltage (T/2) ✓

Phase voltage phase (T/2) ✓

phase voltages wave shapes (wave shape filter)

phase-phase voltages wave shapes (wave shape filter) +/- threshold
residual/neutral-ground voltage wave shape (wave shape filter)
RMS phase currents (T/2) ✓ ✓ ✓

RMS total / neutral current (T/2) ✓ ✓

Power frequency (T/2) ✓ ✓ ✓

Binary inputs (debounced) rising, falling slope

Command external

2.6 PQ Events
trigger quantity lower upper
Voltage dip (T/2) ✓
Voltage swell (T/2) ✓
Voltage interruption (T/2) ✓
Voltage rapid voltage change (T/2) sliding average filter
mean +/- threshold
Voltage change (10min) ✓ ✓
Voltage unbalance (10min) ✓
Mains signalling voltage (150/180T) ✓
Voltage harmonics (10min) ✓
Voltage THD (10min) ✓
Voltage short term flicker PST (10min) ✓
Voltage long term flicker PLT (10min) ✓
Power frequency (10s) ✓ ✓

Design Page 19

Page 19
2.7 Online mode for direct readings
Measurement / Functions
Oscilloscopic recorder
Voltage and current harmonics n=2..50
Voltage and current interharmonics n=0..49
Voltage and current harmonics 2-9kHz
Frequency spectra up to 20 kHz of voltages and currents
Online streaming of all data classes and all measured values

Page 20 Design
3. Order specifications PQI-DE
For determining the smart code ordering details:
0 Only one unit can be ordered for codes with the same capital letter.
0 When a code's capital letter is followed by the number 9, additional information in plain text is required.
0 When a code's capital letter is followed only by zeros, the code may be omitted.
Characteristic Code

Power Quality Interface and fault recorder PQI-DE

0 4 voltage converters, 4 current transformers
0 In accordance with DIN EN 50160 and IEC 61000-4-30 (Class A)
0 8 digital inputs
0 4 relay outputs
0 WinPQ Lite software for PQI-DE
Supply voltage (operation range)
0 AC 90 V..110 V..264 V or DC 108 V..220 V..350 V H1
0 DC 18 V...60 V...75 V H2
0 DC 40 V…160V H3

Voltage inputs
0 100V 2MOhm||25pF (150V CATII) E1
0 100V / 400 V / 690V 10MOhm ||25pF (300V CAT IV) E2
0 3,25V 2MOhm || 50pF for small signal transducer IEC 61869-11 (SELV) E3

Current inputs
0 4 current inputs for metering circuit 1A/5A (range 10A) C30
0 4 current inputs for protection circuit 1A/5A (range 100A) C31
0 4 current inputs for Rogowski Coils (330mV input) C40
0 4 AC current inputs for current clamps (0,5V input AC converter) C44
0 4 DC current inputs for current clamps (5V input DC converter) C45

Binary inputs
0 8 programmable binary inputs (AC/DC 48..250V) M1
0 8 programmable binary inputs (DC 10..48V) M2

Option IEC 61000-4-7 (40.96 kHz sampling)

0 10.24 kHz sampling; without 2 kHz to 20kHz measurement B0
0 Frequency measurement of voltage and current from 2 kHz to 20kHz accord- B1
ing IEC61000-4-7; 40.96 kHz sampling oscilloscope recorder

Option RCM
0 Without Residual current monitor RCM (5th current input) D0
0 Residual current monitor RCM (5th current input) (Firmware V2.2) D1

Option communication protocol

0 Modbus RTU & TCP P0
0 IEC 60870-5-104 (RJ45) P1
0 IEC 61850 (RJ45) P2
0 Modbus Master (Option P3) für I-Sense Strom Abgangsmessung und Aufzeich- P3
nung

Order specifications PQI-DE Page 21

Page 21
Option Data format
0 Without PQDIF export function according to IEEE1159-3 F0
0 With PQDIF export function according to IEEE1159-3 F1
Data transfer via feature P2 - IEC61850 / MMS

Operating instructions
0 German G1
0 English G2

3.1 Option PQI-DE

Software WinPQ lite Code

Software WinPQ lite

For parameterising , as well as reading measurement data and online data as a single-user licence –
free of charge

Expansion WinPQ lite 900.9287

For recalibration of the PQI-DA smart and test report creation

WinPQ database Code

Software WinPQ WinPQ

For parameterization, archiving and evaluation of PQI-D, PQI-DA, PQI-DA smart and PQI-DE
measurement data with the following basic functions:
0 32-bit/64-bit Windows program interface
0 Database for saving the measured values per measuring point
0 Data access via TCP/IP network
0 Visualization option for all measured variables retrievable from a PQI-D, PQI-DA, PQI-DA
smart and PQI-DE as a function of time and as a statistical variable
0 Automatic reporting according to EN50160; IEC61000-2-2 / 2-4; IEEE519; etc.
0 Automatic export functions (Comtrade, PQDif, ASCII, PDF) and fault report transmission
0 One additional workstation license for one Windows user is included in the price
Licences
0 as single-user license for 2 PQ measuring instruments L0
(PQI-D, PQI-DA, PQI-DA smart, PQI-DE)
0 as single-user license for 2 to 10 PQ measuring instruments L1
(PQI-D, PQI-DA, PQI-DA smart, PQI-DE)
0 as single-user license for > 10 PQ measuring instruments L2
(PQI-D, PQI-DA, PQI-DA smart, PQI-DE)
0 as single-user license for > 100 PQ measuring instruments L3
(PQI-D, PQI-DA, PQI-DA smart, PQI-DE)

Operating instructions
0 German A1
0 English A2

Page 22 Order specifications PQI-DE

Additions to PQI-DE Code

SD-memory card (external): 4 GByte industrial standard 900.9099.4

Radio time clock interface DFC 77 111.9024.01

GPS-Clock – Navilog Set - RS485 . DIN-Rail 111.7083

GPS receiver, GPS converter 5m connection cable, mounting bracket
Power supply for Navilog (DIN rail power supply, 88-264VAC/24V, 10W) 111.7079

19" mounting frame - 6 HE - aluminium, anodised, dimensions: W x H:483x267

0 with one cut out (138 x 138 mm) for a PQI-DE 564.0144.01
0 with two cut-outs (138 x 138 mm) for two PQI-DE 564.0144.02

Order specifications PQI-DE Page 23

Page 23
A. Eberle GmbH & Co. KG

Frankenstraße 160
D-90461 Nuremberg

Tel.: +49 (0) 911 / 62 81 08-0

Fax: +49-(0)911-62 81 08 99
E-mail: info@a-eberle.de
http://www.a-eberle.de

Presented by:

_______________________________

Copyright 2022 by A. Eberle GmbH & Co. KG

Subject to change without prior notice.

Version: 8/17/2023 9:57 AM

Page 24 Order specifications PQI-DE