GE Measurement & Control

2300 Series Vibration Monitors

Bently Nevada* Asset Condition Monitoring

Description
The 2300 Monitors feature two seismic channels and a speed
channel, providing continuous monitoring and protection for BOP
(Balance of plant) equipment. It is a perfect match for proactively
managing your assets, rather than waiting until production
outages to replace equipment.

The 2300 series monitors enable condition based monitoring and

protection with support for various interfaces and functions.
Inputs include seismic and speed transducers, and outputs include
relays, buffered output, TCP/IP Ethernet, and an LCD display. This
monitor is available with either 4-20 mA output (2300/20 1) or a
TrendMaster SPA line interface (2300/25 2).

The 2300/20 Monitor can be used to replace legacy Bently Nevada

monitors such as the 1900/27, but more importantly it is a full
featured monitor for use in monitoring and protecting assets such
as motors, pumps, and fans.

The monitor is software configurable, and includes configuration

software. There is also an integrated LCD and multiple LEDs to
show the channels’ real-time data and status locally.

Effective plant asset management, and particularly effective fleet

management of machinery assets, often depends on remote
access using condition monitoring software such as System 1*
Evolution.

1 Modbus® (2nd Quarter 2016)

2 2300/25 (2nd Quarter 2016)

Part Number: 105M0340-01

Rev. E (10/15)

Page 1 of 10
Monitor Key Features

2300/20 2300/25
 Two 4-20mA outputs  Trendmaster SPA interface
 Two relay outputs with programmable setpoints  Two relay outputs with programmable setpoints
 Ethernet 10/100 Base-T communication for  Ethernet 10/100 Base-T communication for
configuration using Bently Nevada Monitor configuration using Bently Nevada Monitor
Configuration software (included) Configuration software (included)
 One dedicated speed and Keyphasor* channel  One dedicated speed and Keyphasor channel
supporting Proximity probes, Magnetic pickup supporting Proximity probes, Magnetic pickup
and Proximity switch type sensors and Proximity switch type sensors
 Three buffered transducer outputs (including  Three buffered transducer outputs (including
Keyphasor signal) providing short circuit and EMI Keyphasor signal) providing short circuit and EMI
protection. Buffered outputs for each signal are protection. Buffered outputs for each signal are
through BNC connectors through BNC connectors
 Continuous monitoring and protection  Continuous monitoring and protection
 LCD display showing vibration amplitude,  LCD display showing vibration amplitude,
setpoints, and speed setpoints, and speed
 Two acceleration inputs with synchronized  Two acceleration inputs with synchronized
sampling for advanced diagnostics sampling for advanced diagnostics
 Key measurements(Direct 0-pk, pk-pk, Direct rms,  Key measurements(Direct 0-pk, pk-pk, Direct rms,
Derived pk, integrated direct pk, Speed) real-time Derived pk, integrated direct pk, Speed) real-time
provided with alarm configuration provided with alarm configuration
 LEDs show the monitor status  LEDs show the monitor status
 Local contacts for positive engagement of  Local contacts for positive engagement of
channel bypass, configuration lockout, and reset channel bypass, configuration lockout, and reset
 Optional Modbus®1 over Ethernet  Optional Modbus®1 over Ethernet

Recommend for Demonstration Kit

2300/20_KIT-003
 1 - 2300/20 Monitor
 1 - 6 ft. (1.8M) shielded Ethernet cable
 2 - Accelerometer sensors
 2 - 12 ft. (3.6M) accelerometer cables
To be ordered separately
110M7102-01 Power supply for DIN rail mounting,
100/240AC to 24DC/1.3A
(-25°C ~70°C, 22.5*99*107 mm)

Part Number: 105M0340-01

Rev. E (10/15)

Page 2 of 10
Specifications  Proximity Switch Interface:
o Supply Voltage: -10 to -24 VDC
o Lower Not Ok limit: -2.75 ±0.05 V
Inputs / Outputs
o Rpm range: 1 to 120,000
Power Input:  Magnetic Pick up:
 DC Input: 18~36VDC, max 7.5W o Input voltage up to ±125V (250Vp-p)
Supports 2 seismic channels: o Rpm range: 200 to 120,000
 Supports ICP accelerometers Contact Inputs
o Bandpass variable: 0.2 Hz High pass, 20 kHz Monitor provides the capability of 3 contact inputs
Low pass with terminals. One is used for configuration lock,
o Scale Factor range: 5 to 575 mV/g one is for alarm reset function, and the 3rd one is
used for monitor Alarm/Relay Inhibit.
o Full scale range: 2 to 80 g peak
 Activate: 0 to 10 kΩ
o Bias output voltage: -12VDC
 De-activate: 150 kΩ to infinite
o Configurable Upper OK limit: -0.25 to -22 V
(greater than lower ok) Button Inputs

o Configurable Lower OK limit: -0.25 to -22 V  External button to reset alarm and relay
(less than upper ok)  One buried button provides 3 functions:
o Current Sink Source: 3.3 mA ± 5% o Display monitor information including:
o Open Circuit Voltage: -21 to -24 VDC  User account/Password
o Accuracy: ±1% of full scale range  IP address
 Supports custom accelerometers (2 or 3 wires)  FW/HW version
 Independent 24-bit ADCs on both channels o LCD contrast adjustment
Speed/Keyphasor Inputs o Reset settings to default including:
 Supported Keyphasor transducers include:  User account name
o Proximity probe  Password
o Proximity switch  Network configuration
o Magnetic Pickup Jumper between COM & Chassis GND
 Supports multiple events per revolution and  There is a 2-pin terminal interface which allows
event ratios for speed inputs up to 20 kHz connection of COM and Chassis GND together.
 Threshold voltage resolution: 0.1VDC  Alternatively, COM can be connected to earth
 Proximity Transducer Interface: ground separately through a terminal.

o Supply Voltage: -22.8 to –25.2 VDC Buffered Output

o Maximum Rated Current: 15 mA  There are three buffered outputs available on the
monitor through BNC connectors:
o Short Circuit Current: 15.1 mA to 23.6 mA
o 2 Vibration Outputs
o Accuracy: ±1% of full scale range
o 1 Tachometer Output
o Input Impedance: 3-wire Voltage Mode, 10
kΩ
o Rpm range: 1 to 120,000

Part Number: 105M0340-01

Rev. E (10/15)

Page 3 of 10
Relay Output
 There are two dry-contact relay outputs SPA Output (2300/25)2
 May be normally energized or de-energized  Input signal range
 No output feedback determination o High AC: 8Vpp
 Relay circuit specification in Non-Hazardous o Low AC: 1.6Vpp
area:
o DC GAP: 0 to -20Vdc (max measurable AC
o Type: Single pole, double throw signal is 1Vpp)
o Sealing: Epoxy sealed  Accuracy
o Contact life: o AC: ±1% of Full-Scale at 100Hz
100,000 cycles @ 5 amps 250 VAC
o DC GAP: ±0.5V
200,000 @ 1 amp, 24 VDC
 Frequency response
o Insulation resistance:
1000 MΩ minimum @ 500 VDC o 1.67Hz to 3000Hz (0% to -5%)
o Relay closed contact resistance: LEDs
1 Ω maximum
 OK: Indicates when the monitor is operating
o Relay open contact resistance: properly
1 MΩ minimum
 Protection fault: indicates a problem with the
o Maximum switched contact voltage: system preventing normal operation
250V AC /250V DC
 User inhibit: indicates the relays have been
o Maximum breaking contact current: intentionally inhibited from operation
6A @250VAC / 6A @24VDC
 Relay status: indicates if relays have been
o Maximum switched power: activated
1500VA AC / 150 Watts DC
 TX/RX: Indicates the Ethernet status and monitor
 Relay circuit specification in Hazardous area: communicating with remote software
o Maximum switched contact voltage and  Speed channel status
current: 6A @24VAC / 5A @30VAC / 5.8A
 Channel Alarm Status:
@24VDC / 4A @30VDC
o Alert LED: engages if any channel is in alert
4-20mA Output (2300/20)
state
 Two 4-20mA outputs
o Danger LED: engages if any channel is in
 4 to 20mA output values are proportional to the danger state
full-scale of the associated measurement
LCD
 Each output can be software configured to
LCD display allows viewing machine speed, vibration
output any variable from channel 1 or 2
levels, setpoints, and configuration information.
 Voltage compliance: 0 to +12Vdc range across
load
 Load resistance: 0 to 600Ω Communications
 Resolution: 0.3662uA
Ethernet
 Accuracy: 1% over operating temperature range
 Ethernet, 10Base-T and 100Base-TX. Conforms
 Update rate: 100ms to IEEE802.3
 2mA clamp current  RJ-45 for 10Base-T/100Base-TX Ethernet cabling
 No output feedback determination  Cable length: 100 meters (328 ft.) maximum

Part Number: 105M0340-01

Rev. E (10/15)

Page 4 of 10
Environmental Limits Intrinsic Safety Parameters:
For Proximitor Transducer:
Operating Temperature:
Uo: 24VDC; Io: 46mA; Co: 200nF; Lo: 1mH
 -30 °C to +65 °C (-22 °F to +149 °F)
For Accelerometer Transducer:
Storage Temperature:
Uo: 24VDC; Io: 3.3mA; Co: 200nF; Lo: 1mH
 -40 °C to +85 °C (-40 °F to +185 °F)
Humidity:
Physical
 Up to 95%, non-condensing
Battery Life for Real Time Clock: Dimensions (Width x Depth x Height)
 Powered: 38 years @ 50°C (122 °F) 127mm x 127mm x 76.2mm (5in x 5in x 3in)
 Un-powered: 12 years @ 50°C (122 °F) Weight
1.03kg (2.26lbs)

Compliance and Certifications Mounting

Panel mount or DIN rail (adapter included)
General and Electrical Safety:
UL Std. No. 61010-1 (3rd Edition)
CAN/CSA C22.2 No. 61010-1-12
2006/95/EC Low Voltage
Standard:
EN61010-1: 2010
European Community Directives:
2006/95/EC Low Voltage

EMC
Standards:
EN61000-6-2 Immunity for Industrial Environments
EN61000-6-4 Emissions for Industrial Environments
EN61326-1 Electrical equipment for measurement,
control and laboratory use - EMC requirements

European Community Directives:

EMC Directive 2004/108/EC

Hazardous Area Approvals

For a detailed listing of country and product
specific approvals, refer to the Approvals Quick
Reference Guide (document 108M1756) located at
the following website: www.GEmeasurement.com.

CSA/NRTL/C
Class I, Division 2/Zone 2
AEx/Ex nA nC [ic] IIC T4 Gc
Class I, Div. 2, Groups A, B, C, D
ATEX/IECEx
II 3 G
Ex nA nC [ic] IIC T4 Gc
Part Number: 105M0340-01
Rev. E (10/15)

Page 5 of 10
Ordering Information (Excluding Keyphasor sensor and 24VDC
power supply 3)
For a detailed listing of country and product
specific approvals, refer to the Approvals Quick 003
Reference Guide (document 108M1756) located at 1 - 2300/20 Monitor
the following website: www.GEmeasurement.com.
1 - 6 ft. shielded Ethernet cable
2300 Series Vibration Monitor 2 - Accelerometer sensors
2 - 12 ft. accelerometer cables
2300/20-AA: Monitor with 4-20ma Outputs
(Excluding Keyphasor sensor, enclosure
(including DIN rail mount assembly, manual and
and 24 VDC power supply 3)
monitor configuration software)
BB: Approvals Option
2300/25-AA: Monitor with SPA Outputs2 00
(including DIN rail mount assembly, manual and None
monitor configuration software)
02
AA: Approvals Option Multiple Explosive Atmosphere
00 Certifications (ATEX/IECEx/CSA)
None
02
3 We provide 3 kinds of power supplies with different temperature
Multiple Explosive Atmosphere
Certifications (ATEX/IECEx/CSA) range and different power. Please check Accessories below for
the details.
2300/20_KIT-AAA-BB: Bently Nevada 2300/20
Condition Monitoring System Kit

2300/25_KIT-AAA-BB: Bently Nevada 2300/25 Accessories

Condition Monitoring System Kit
106M7607-01 Power supply for DIN rail mounting,
AAA: Configuration
100/240AC to 24DC/1.5A
001 Certifications (ATEX)
(-25°C ~70°C, 35*99*95 mm)
1 - 2300/20 Monitor
(One power can drive max 4
1 - 6 ft. (1.8m) shielded Ethernet cable monitors)
1 – 13 x 15 x 8 in. (338 x 389 x 209mm) 110M7102-01 Power supply for DIN rail mounting,
fiberglass housing with window 100/240AC to 24DC/1.3A
2 - Accelerometer sensors Certifications (CID2 by UL)
(-25°C ~70°C, 22.5*99*107 mm)
2 – 12 ft. (3.6m) accelerometer cables (One power can drive max 4
(Excluding Keyphasor sensor and 24 VDC monitors)
power supply 3) 106M6694-01 Power supply for DIN rail mounting,
110/220AC to 24VDC/5A
Certifications (ATEX, IECEx, CID2 by
002 UL)
(-40°C ~70°C, 40*130*125 mm)
1 - 2300/20Monitor
1 - 6 ft. shielded Ethernet cable
1 - 13x15x8 in. fiberglass housing with
window
1 - Accelerometer sensor
1- 12 ft. accelerometer cable
Part Number: 105M0340-01
Rev. E (10/15)

Page 6 of 10
105M6193-01 Fiberglass NEMA 4X/IP68 100M0741 Proximity Switch
weatherproof housing with window
in door (includes mounting plate for
monitor)

Dimensions:
(Width x Depth x Height)
338.3 x 389.1 x 209.8mm
(13.3 x 15.3 x 8.2in)

284947 Magnetic Pickup

Proximity Probes

Please refer to proximity probe datasheet for details

141194-01 3300XL 8mm

146256-01 3300XL 11mm

147385-01 3300XL NSV

02120015 Bulk Cable from Proximity sensor to

monitor (500 ft.)

AM3100T2-Z2 Accelerometer sensor 9571-AA Low cost cable for accelerometer

AA: From “20” to “99” Increments of 1.0 foot

84661-AA Armored cable for accelerometer

AA: From “30” to “99” Increments of 1.0 foot

Part Number: 105M0340-01

Rev. E (10/15)

Page 7 of 10
CB2W100-AAA Cable for accelerometer Software
AAA:
016 16 ft. (4.8 m) 100M9465-01 BN Monitor Configuration SW/FW
032 32 ft. (9.8 m) DVD
064 64 ft. (19.5 m)
112 112 ft. (34.1 m) o BNMC version 4.0 or greater
125 125 ft. (38.1 m) o 2300 series monitor firmware
150 150 ft. (45.7 m)
200 200 ft. (61.0 m) (DVD including BNMC Configuration
250 250 ft. (76.2 m) Guide)
Note: Cable lengths greater than 30 meters (100 feet)
will experience some attenuation of amplitudes at
higher frequencies. User Manual

Bently_Manuals 2300 Series Operation and

286244 Magnetic mounting base ¼-28 Maintenance Manual
threaded hole (Document 105M0341)

Ethernet Cables
Training Materials Link
138131-AAA Standard 10 Base-T/100 Base-TX http://ge-
Shielded Category 5 Cable with energy.turnstilesystems.com/ProgramDetail.aspx/23
RJ-45 connectors (solid conductor) 00Monitor

AAA: Cable Length

006 6 ft. (1.8 m)
010 10 ft. (3.0 m)
025 25 ft. (7.6 m)
040 40 ft. (12.2 m)
050 50 ft. (15.2 m)
075 75 ft. (22.9 m)
085 85 ft. (25.9 m)
100 100 ft. (30.5 m)

Spares

105M6203-01 35mm DIN rail mount and screws

(included with 2300/20 monitor)

106M3210 10 pins 4-20mA output connector

106M2223 5 pins contact input connector

(Alarm Reset)

106M3408 5 pins contact input connector

(Alarm Inhibit, Config lock)

106M3211 16 pins transducer input connector

106M3212 6 pins relay output connector

106M2231 3 pins power input connector

Part Number: 105M0340-01

Rev. E (10/15)

Page 8 of 10
Graphs and Figures

2300 Series Monitor Recommended Clearance

Part Number: 105M0340-01

Rev. E (10/15)

Page 9 of 10
Wiring Diagram

2300 Series Wiring Diagram

Note: 2300/20 and 2300/252 uses the same interface connector for recorder output or SPA output.

1 Modbus (2nd Quarter 2016)

2 2300/25 (2nd Quarter 2016)

Modbus® is a registered trademark of Schneider Electric USA, INC.

© 2014-2015 Bently Nevada, Inc. All rights reserved.

* Denotes a trademark of Bently Nevada, Inc., a wholly owned subsidiary of General Electric Company.
The information contained in this document is subject to change without prior notice.
Printed in USA. Uncontrolled when transmitted electronically.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 775.782.3611 Fax: 775.215.2873
www.GEmeasurement.com
Part Number: 105M0340-01
Rev. E (10/15)

Page 10 of 10