Freja 300: Relay Testing System
Freja 300: Relay Testing System
F R EJA 300
FREJA 300
Operation
Relay Testing
Using the dial by turning and clicking it is easy to make the settings.
All settings are saved automatically when you exit, but if you prefer
you can assign the settings a name and save them separately for
convenient access when you conduct your next test. The display can
also show the measured value that is being generated. This feature is
equivalent to three voltmeters and three ammeters that present RMS
values for all generators.
ANSI No.
Distance protection equipment
21
Synchronising or synchronism-check relays
25
Undervoltage relays
27
Directional Power relays
32
Undercurrent or underpower relays
37
Negative sequence overcurrent relays
46
Overcurrent-/ ground fault relays
50
Inverse time overcurrent-/ ground fault relays
51
Power factor relays
55
Overvoltage relays
59
Voltage or current balance relays
60
Directional overcurrent relays
67
DC overcurrent relays
76
Phase-angle measuring or out-of-step protective relays 78
Automatic reclosing devices
79
Frequency relays
81
Differential protective relays
87
Directional voltage relays
91
Voltage and power directional relays
92
Control center
F R EJA 300
Application
F R EJA 300
Binary inputs.
Multiconnector for voltage (L1U, L2U, L3U, NU) and current (L1I, L2I, L3I, NI).
DC-supply, connect to (10) to read the values (in General mode page 5/6 on the display).
F R EJA 300
Calibration box
F R EJA 300
Specifications are valid for resistive load, nominal voltage supply and
ambient temperature +25C 3C, (77F 5.4F) after 30 minutes
warm up time. All hardware data are for full scale values. Specifications are subject to change without notice.
Environment
Application field
Temperature
Operating
Storage & transport
Humidity
EMC
20 mA
SW 0.1 A
HW 0.6 A
0.01% typical,
0.03% guaranteed (= 6 A)
10 V
SW 0.1 mV
HW 0.3 mV
0.01% typical,
0.03% guaranteed (= 3 mV)
3 X 0...2 VRMS
3 X 0...2 VRMS
5 mA
<0.1% typ. (<0.2% guaranteed)
250 V
<0.05% typ. (<0.1% guaranteed)
5 minutes
Generator section
Voltage outputs L1U, L2U, L3U
Measurement section
Binary inputs
Internal resolution
time
Galvanic isolation
<1% 1digit
<2% 2digit
Binary outputs
Break capacity AC
Break capacity DC
General
Number
Type
Inaccuracy
Voltage AC/DC
Current AC/DC
Number
Type
CE-marking
LVD
14 A DC, 10 A ACRMS
DC <0.1%, AC <0.3%
Range
4-phase AC
1-phase AC (L-L)
DC (L-N)
Power
3-phase AC
1-phase AC (L-L)
DC (L-N)
Resolution
SW
HW
Inaccuracy3) (guaranteed)
Distortion (THD+N)4)
4 x 150 V
2 x 300 V
180 V
3 x 82 VA at 150 V
1 x 140 VA at 300 V
87 W
10 mV
6.5 mV
(0.01% of range) + (0.05% of reading)
0.02% typical (0.04% max)
3 x 15 A
1 x 45 A
15 A
3 x 87 VA
1 x 250 VA
3 x 87 W (max)
1 mA
0.65 mA
(0.01% of range) + (0.3% of reading)
0.1% typical (0.2% max)
F R EJA 300
Generators, general
Frequency range
Continuous signals DC 2000 Hz
Transient signals
DC 3.5 kHz
Frequency resolution 1 mHz
Frequency inaccuracy 0.01%
Phase angle range
0 360
Phase resolution
0.1
0.1
Phase inaccuracy3)
Connection (Amplifier 4 mm stackable safety plugs or 8-pin
outputs)
amplifier multiconnector
All seven generators are continuously and independently adjustable
in amplitude and phase. No switching of range is necessary. All current and voltage outputs are fully overload- and short-circuit-proof
and protected against external high voltage transient signals and
overtemperature.
Note! To allow continuous generation of high DC current (12 - 15
A), a minimum load impedance of 0.2 Ohm is required. For lower
load impedances, e.g. short-circuit, the time is limited to 1 minute.
20 210 V DC
75 W at 210 V
1)
2)
3)
4)
50 or 60 Hz AC + harmonics only
Parallel connection
For sinusoidal signals at 50/60 Hz
THD+N: Values at 50/60 Hz, at max amplitude, 50% power and resistive load. Measurement bandwidth 22 Hz 22 kHz
5) For higher current or output power you can use amplifier CA30
Ordering information
Complete with: FREJA Win Standard, FREJA PC
software key, Two test lead sets, Calibration box,
Hard transport case
Same as above but with soft transport case
Other
On-line measurement of the current and voltage output, presented
on the built-in display.
Calibration check when the temperature is changed. Full calibration
can be conducted a any time using the FREJA calibration box. This
means you do not need to send away FREJA for calibration. Only the
calibration box needs to be sent for calibration once per year.
Connection to PC (minimum Pentium II 266 MHz, 32Mb RAM,
Win 95/98/2000, NT 4.0) via the serial port. The FREJA has a built-in
switch that enables you to switch communication back and forth
between the PC and your relay.
Art.No.
FREJA 300
CF-19091
CF-19090
CF-19000
CF-19004
CF-19098
Optional accessories
See section Relay testing accessories
CF-19099
Programma Electric AB
Eldarvgen 4
Box 2970
SE-187 29 TBY
Sweden
2008