SOM 2 Marks

UNIT I
STRESS, STRAIN AND DEFORMATION OF SOLIDS

1. Define Poissons Ratio.
The negative ratio of lateral strain to the longitudinal strain is known as Poissons ratio.
2. What is thermal Stress?
If the expansion of a structural member is constrained, it will cause stresses to develop which are
known as thermal Stress.
3. State HookesLaw.
The Ratio of stress to the strain with in elastic limit is known as Hookes Law.
4. Define Bulk Modulus.
The Ratio of direct stress to the corresponding volumetric strain is known as Bulk Modulus.
5. Define Modulus of resilience.
Proof resilience per unit volume is defined as Modulus of resilience.
6. Define Elasticity.
It is the property of material to regain its original shape and dimensions on removing external
load acting on it.
7. Give the relation between Modulus of Elasticity and Modulus of Rigidity.
The relation between modulus of elasticity and modulus of rigidity are as follows
E= 2G(1+v)
8. What is Strain Energy?
The Workdone is stored in rod and is known as strain energy.
9. Define Proof Resilience.
The maximum strain energy that can be stored in a body without permanent deformation is known as
Proof resilience.
10. Define compressive stress.
The Resistance offered by the section of member or body against the decrease in length due to
applied pushing load.
11. Define: Bulk-modulus
The ratio of direct stress to volumetric strain is called as bulk modulus..
Bulk modulus, K = Direct stress / Volumetric strain
12. Define: Shear modulus or Modulus of rigidity
The ratio of shear stress to shear strain is called as bulk modulus.. Shear modulus,
G = shear stress / shear strain
13. State the relationship between Youngs Modulus and Modulus of Rigidity.
E = 2G (1+)
Where,
E - Youngs Modulus
G Modulus of rigidity
- Poissons ratio
14. Give the relationship between Bulk Modulus and Youngs Modulus.
E = 3K (1-2)
Where,E - Youngs Modulus
K - Bulk Modulus
- Poissons ratio
15. What is principle of super position?
The resultant deformation of the body is equal to the algebric sum of the deformation of the
individual section. Such principle is called as principle of super position
16. What is compound bar?
A composite bar composed of two or more different materials joined together such that the system is
elongated or compressed in a single unit.
17. What you mean by thermal stresses?
If the body is allowed to expand or contract freely, with the rise or fall of temperature no stress is
developed, but if free expansion is prevented the stress developed is called temperature stress or strain.
.
18. Define principle stresses and principle plane.
Principle stress: The magnitude of normal stress, acting on a principal plane is known as
principal stresses.
Principle plane: The planes which have no shear stress are known as principal planes.
19. What is the radius of Mohrs circle?
Radius of Mohrs circle is equal to the maximum shear stress.
20. What is the use of Mohrs circle?
To find out the normal, resultant and principle stresses and their planes.
21. List the methods to find the stresses in oblique plane?
1. Analytical method
2. Graphical method
UNIT II
TRANSVERSE LOADING ON BEAMS AND STRESSES IN BEAMS
1. State the assumptions while deriving the general formula for shear stresses.
i. The material is homogenous, isotropic and elastic.
ii. The modulus of elasticity in tension and compression are same and the
shear stress is constant along the beam width.
2. Define shear stress distribution.
`
The variation of shear stress along the depth of beam is called shear stress distribution.
3. Mention the different types of beams.
i. Cantilever beam,
ii. Simply supported beam,
iii. Fixed beam,
iv. Continous beam and
v. Over hanging beam
4. Write down the bending moment equation.
The bending equation M /I = /y =E/R
Where,
M bending moment
I moment of inertia of the section,
bending stress at that section,
y distance from the neutral axis,
E Youngs modulus of the material,
R radius of curvature of the beam.
5. What do you understand by the term point of contraflexure?
The point where the shear force changes its sign or zero is called as point of contraflexure.At this
point the bending moment is maximum.
6. What is the value of bending moment corresponding to a point having a zero shear
force?
The value of bending moment is maximum where the shear force changes it sign or zero.
7. Mention the types of supports.
Roller support
Fixed support
Hinged or pinned support
8. Define bending moment in beam.
The bending moment of the beam may be defined as the algebraic sum of the moments of the forces,
to the right or left of the section.
9. Define shear force.

Shear force at any section is defined as the algebraic sum of all forces acting on either side of a
beam.
10. What is meant by Neutral axis of the beam?
It is an imaginary plane, which divides the section of the beam into the tension and compression
zones on the opposite sides of the plane.
11. What is mean by compressive and tensile force?
The forces in the member will be compressive if the member pushes the joint to which it is
connected whereas the force in the member will be tensile if the member pulls the joint to which it is
connected.
12. How will you determine the forces in a member by method of joints?
In method of joint after determining the reactions at the supports, the equilibrium of every
support is considered. This means the sum all vertical forces as well as the horizontal forces acting on a
joint is equated to zero. The joint should be selected in such a way that at any time there are only two
members, in which the forces are unknown.
13. What are the benefits of method of sections compared with other methods?
1. This method is very quick
2. When the forces in few members of the truss are to be determined, then the method of section is
mostly used.
UNIT III TORSION

1. What are the assumptions made in torsion equation?
The material of the shaft is homogeneous, perfectly elastic and obeys Hooks law.
Twist is uniform along the length of the shaft and
The stress does not exceed the limit of proportionality
2. Write down the expression for power transmitted by a shaft.
Power, P = 2NT/ 60
Where,
T Torque in kN.m
N Speed in r.p.m.
P Power in Kw
3. Define polar modulus.
It is the ratio between polar moment of inertia and radius of the shaft.
4. State the differences between closed and open coil helical springs.
Closed coiled helical springs
Open coiled helical springs
Adjacent coils are very close to each other

It can carry only tensile loads .
Large gap between adjacent coils

It can carry Both tensile and Compression
loads.
Helix angle is considerable
Helix angle is negligible
5.Find the torque which a shaft of 50mm diameter can transmit safely, if the
allowable shear stress in 75 N/mm?
T = / 16 x fsx d3
T = / 16 x 75 x (50)3
T = 1.840 kN.m
6. What is mean by stiffness?
The stiffness of the spring is defined as the load required to product unit deflection.
7.Classify the types of springs.
Torsion spring and
Bending spring
8.What is meant by spring?
Spring is a device which is used to absorb energy by taking very large change in its form without
permanent deformation and then release the same when it is required.
9.Define torsion.
When a pair of forces of equal magnitude but opposite in direction acting on body, it tends to twist
the body. It is known as twisting moment or simply as torque.
10.what is meant by torsion spring?
A spring, which is subjected to torsion or twisting moment only is known as torsion spring.
11. What is the ratio of maximum shear stress to the average shear stress in the case of
solid circular section?
Qmax is 4/3 times the Qavg.
12. Where the shear stress is max for Triangular section?
In the case of triangular section, the shear stress is not max at N A. The shear stress is max at a
height of h/2
13. Define: Mohrs Theorem for slope
The change of slope between two points of a loaded beam is equal to the area of
BMD between two points divided by EI.
Slope,
UNIT IV- DEFLECTION OF BEAMS

1. List any four methods of determining slope and deflection of loaded beam?
i)Double integration method, ii)Macaulays method, iii)Moment area method and iv)Conjugate
beam method
2. What is the relation between slope, deflection and radius of curvature of a beam?
1/R =(d2y)/(dx2)
Where R =radius of curvature.
Y= deflection.
3. State two assumptions made in the Eulers columns theory
i)The cross section of the column is uniform throughout its length and
ii)The length of the column is very long as compared to its cross sectional dimensions.
4. State Slenderness ratio
The ratio between actual length to least radius of gyration Slenderness ratio = L / k
5. Describe the double integration method.
While integrating twice the original differential equation, we will get two constant C 1 and C2. The
value of these constants may be found by using the end conditions.
6. Define shear force and bending moment?
SF at any cross section is defined as algebraic sum of the vertical forces acting either side of
beam.
BM at any cross section is defined as algebraic sum of the moments of all the
forces which are placed either side from that point.
7. When will bending moment is maximum?
BM will be maximum when shear force change its sign.
8. What is maximum bending moment in a simply supported beam of span L subjected to UDL of
w over entire span?
2
Max BM =wL /8
9. In a simply supported beam how will you locate point of maximum bending moment?
The bending moment is max. when SF is zero. Writing SF equation at that point
and equating to zero we can find out the distances x from one end .then find maximum
bending moment at that point by taking moment on right or left hand side of beam.
10. What is shear force and bending moment diagram?
It shows the variation of the shear force and bending moment along the length of the beam.
11. What are the types of beams?
1. Cantilever beam
2. Simply supported beam
3. Fixed beam
4. Continuous beam
5. over hanging beam
12. What are the types of loads?

1. Concentrated load or point load
2. Uniform distributed load (udl)
3. Uniform varying load(uvl)
13. Write the assumptions in the theory of simple bending?
1. The material of the beam is homogeneous and isotropic.
2. The beam material is stressed within the elastic limit and thus obey hookes law.
3. Each layer of the beam is free to expand or contract independently about the layer, above or
below
4.The value of E is the same in both compression and tension
14. Write the theory of simple bending equation?

M - Maximum bending moment
Where, I - Moment of inertia
f - Maximum stress induced
y- Distance from the neutral axis
E - Youngs modulus
R Radius of neutral layer.
15. Define: Neutral Axis
The N.A of any transverse section is defined as the line of intersection of the neutral layer
with the transverse section.
16. Define: Moment of resistance
Due to pure bending, the layers above the N.A are subjected to compressive stresses,
whereas the layers below the N.A are subjected to tensile stresses. Due to these stresses, the forces
will be acting on the layers. These forces will have moment about the N.A. The total moment of these
forces about the N.A for a section is known as moment of resistance of the section.
17. Define: Section modulus
Section modulus is defined as the ratio of moment of inertia of a section about the
N.A to the distance of the outermost layer from the N.A.
Section modulus,
Where, I M.O.I about N.A
ymax - Distance of the outermost layer from the N.A
UNIT-V
THIN CYLINDERS, SPHERES AND THICK CYLINDERS
1. List out the modes of failure in thin cylindrical shell due to an internal pressure.
i)Circumferential or hoop stress
ii)Longitudinal stress
2. What do you mean by principal plane?
The planes which have no shear stress are known as principal planes.
3. What are assumptions involved in the analysis of thin cylindrical shells?
The material of the cylinder is homogeneous, isotropic and obeys Hooks law.
i)The hoop stress distribution in thin cylinder is uniform over the cross section from inner
to outer surface since the thickness of the cylinder is thin and
ii)Weight of fluid and material of the cylinder is not taken into account.
4. Define Circumferential and Hoop stress.
A thin cylinder shell is subjected to an internal pressure, as a result of internal pressure, the
cylinder
has tendency to split up into two troughs is called circumferential stress. The same cylinder
shell, subjected to the same internal pressure, the cylinder also has a tendency to split in to
two ieces is known as Hoop stress.
5. Define thin cylinder?
If the thickness of the wall of the cylinder vessel is less than 1/15 to 1/20
of its internal diameter, the cylinder vessel is known as thin cylinder.
6. What are types of stress in a thin cylindrical vessel subjected to internal pressure?
These stresses are tensile and are know as
1.Circumferential stress (or hoop stress ) 2.Longitudinal
stress.
7. What is mean by circumferential stress (or hoop stress) and longitudinal stress?
The stress acting along the circumference of the cylinder is called
circumferential stress (or hoop stress) whereas the stress acting along the length of the
cylinder is known as longitudinal stress.
8. What are the formula for finding circumferential stress and longitudinal stress?
Circumferential stress, f1 = pd / 2t
longitudinal stress, f2= pd /4t

SOM 2 Marks

Uploaded by

Copyright:

Available Formats

SOM 2 Marks

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SOM 2 Marks

Uploaded by

Copyright:

Available Formats

UNIT I

STRESS, STRAIN AND DEFORMATION OF SOLIDS

9. Define shear force.

UNIT III TORSION

Open coiled helical springs

Adjacent coils are very close to each other

Large gap between adjacent coils

Helix angle is negligible

UNIT IV- DEFLECTION OF BEAMS

12. What are the types of loads?

14. Write the theory of simple bending equation?

You might also like