Tooling - Chapter 3

Tooling
This chapter sponsored by R.L. Best Company www.rlbest.com

This chapter covers the semi-permanent press tooling: dummy blocks, stems,
containers, container liners, and their repair, maintenance, and lubrication.

Fixed Dummy Blocks

Most aluminum extrusion presses are now fitted with fixed dummy blocks. They offer
several advantages over loose dummy blocks:

Operator involvement is virtually eliminated.

Expense and downtime due to a handling system for loose dummy blocks are
eliminated.

Slightly longer billets are possible (typically about 2 inches [50mm] longer.

Butt disposal is simplified.

Eliminates damage to front of container from loose dummy blocks.

Eliminates the risk of extruding without a dummy block or having dummy block fall
over in the loader.

Dead cycle time may usually be reduced.
To successfully apply fixed dummy blocks to your press, several factors must be
considered:
Design of the Fixed Block. Several proprietary designs for fixed dummy blocks are available on
1,2,3,4
the market today. The design principles have been well described in previous publications
and will not be reviewed here. In general, the geometry of the body of the block expands under
extrusion load, causing the outer edge to expand practically to the inside diameter of the
container. The expansion is caused by pushing the insert into the body of the block. At the end of
extrusion, relaxation of press pressure allows the insert to retract and the body to contract in
diameter, helping to push the butt away from the face of the block.
Dummy block failure is usually related to the limited elasticity of the steels used and the
extreme stresses involved, which tend to expand the block past the steels creep limits. When the
blocks outside diameter experiences a permanent increase of 0.020 (0.5mm), permanent loss of
elasticity is likely to have occurred. Common problems are the build-up of excessive aluminum on
the block, causing high drawback loads and blistering; and wear on the periphery of the block.
Fixed dummy blocks are commonly constructed of alloy H-13 steel, and hardened to
Rockwell C 45 - 49.
Clearance Within the Container. The diameter of the dummy block must be selected to allow a
tight seal to the container during extrusion, and sufficient clearance to pass easily through the
container during the return stroke. There is no general agreement on the proper clearance, as it
will depend somewhat on the design of the block. Also, poor press alignment will require greater
clearance and thus poorer block performance. Recommended clearances between block and
1
Castle, Alan F., Improving Fixed Dummy Block Performance, Proceedings of 6th International
Aluminum Extrusion Technology Seminar, Vol. I, (1996), p. 301-304.
2
Bessey, Guy, Fixed Dummy Block Design, Proceedings of 4th International Aluminum Extrusion
Technology Seminar, Vol. II, (1988), 131-133.
3
Castle, Alan F., Fixed Dummy Block Extrusion, Proceedings of 4th International Aluminum
Extrusion Technology Seminar, Vol. II, (1988), 134-138.
4
Robbins, Paul, Dummy Blocks, Clean Out Blocks, Lubrication and Film Coatings, and Alignment
(the Enemy), presented at AEC Press Maintenance Seminar, (1995), Chicago.

3-1
Tooling - Chapter 3

container vary: most commonly 0.030 (0.75mm); but 0.4 to 1.0mm (0.016 to 0.040) according to
5
other sources . In fact, most press operators must arrive at the optimum clearance for their
situation by trial and error.
Method of Attachment to the Ram Stem. Once again, different proprietary designs tend to
prevail. The most basic method of attachment is a threaded stud connecting ram stem to dummy
block; drawbacks to this design include inflexibility, seizing, difficult changing, and occasional
loosening of the block. If the block becomes loose on the stud, the full force of extrusion will
come to bear on the stud and will likely break it. Keys and dowels are commonly used to prevent
loosening.
A second popular design is the tie bar passing
through the stem to a nut at the rear. In this case the
base of the block is always in contact with the stem,
avoiding excessive loads on the threads.
A proprietary bayonet-type design is said to
permit quick change of the block. It is also said to avoid
thread damage and to accommodate a small amount of
misalignment by permitting some radial movement. (See
Figures 3-3 and 3-7)
Press Alignment. Alignment of the ram stem and
container have been discussed under Chapter 2: Press
Alignment. Service life of fixed dummy blocks will be
Figure 3-1: Fixed dummy block
dramatically reduced by poor alignment. Most (Photo courtesy of Castool)
authorities recommend that misalignment never exceed
0.020 (0.5mm).
Preheating the Dummy Block. Although the process
of extrusion will generate considerable heat, the fixed
dummy block still should be preheated before it is
placed in service. Preheating will minimize thermal
shock and also increase the toughness of the steel,
which is higher at press operating temperatures. A
o o
recommended temperature is about 600 F (315 C).
The block may be preheated in a special oven, or by
leaving it in the center of the container for a few hours.
However, do not leave the block in any oven for more Figure 3-2: Fixed dummy block with
than a couple of hours, in order to avoid decarburization replaceable wear ring
and loss of temper. (Illustration courtesy of Castool)

Lubrication of the Dummy Block and Billet. This

subject has been discussed under Lubrication of
Extrusion Press Tooling page 3-27. In general, to
eliminate sticking of aluminum to the steel dummy
block, lubricant(s) must be applied to the block and/or
billet. Most operators lubricate the block by manual or
automatic application of water-borne specialty lubes, or
manual swabbing of graphite compounds. The ends of
pre-cut billets may be painted with specialty lubes or Figure 3-3: Fixed dummy block with
graphite. Sheared billets must be coated after shearing, bayonet mount and replaceable wear
using flame-generated carbon or spray-applied specialty ring (Illustration courtesy of Castool)
products such as Boron Nitride.

5
Castle, Alan F., Ibid.

3-2
 Tooling - Chapter 3

Figure 3-4: Fixed dummy block for oblong billet

(Photo courtesy of COMPES)

Repairing the Fixed Dummy Block. Replacement is most commonly needed due to wearing of
the land area, increase in pick-up during drawback, or loss of elasticity. Castool offers a patented
design with a replaceable wear ring.
Worn land areas of dummy blocks may be repaired by welding and re-machining to the
6
original diameter. Castle offers a welding procedure for H-13 blocks:
o o
Preheat to approximately 400 C (750 F)
o o
Weld using a gas-shielded arc process (temperature should not fall below 350 C (660 F)
o o o o
Slow cool in air to 80 -100 C (175 -212 F) -- very important!
Double temper
7
Preventing Dummy Block Damage from the Container Seal Face . The main cause of
stem/dummy block breakage is container shifting caused by a build-up of aluminum on the mating
surfaces of the die and container seal face. This area needs to be kept in good condition and free
of aluminum.
Liner ID (inside diameter) may be constricted (coined) from using small dies.
Dummy block should never completely pass through the exit end of the container.
Butt shear should cut clean on the die face.

6
Castle, Alan F., Fixed Dummy Block Extrusion, Proceedings of 4th International Aluminum
Extrusion Technology Seminar, Vol. II, (1988),p. 134-138.
7
From Castool Solutions Bulletin Fixed Dummy Block.

3-3
Tooling - Chapter 3

Acetylene torches and pneumatic tools should never be used to clean the sealing face.
Container travel should be slowed prior to impacting the die face.
When a burp cycle is needed, do not open the container, only the ram and seal pressures
should be reduced.
Explosions caused by air and lubricant should be eliminated.
8
Dummy Block Maintenance . The dummy block should be inspected daily. It should be visually
checked for aluminum build-up on the face and land. The land should also be checked for signs
of explosions. On blocks with springs, the mandrel should be free and forward from the face of
the dummy block. This confirms that the spring is functioning. At the same time, the cap screws
securing the bayonet lug and keys should be checked for tightness.
Once each week the dummy block should be removed from the press and cleaned in
caustic. It should be visually inspected for wear and accurately measured across the face, the
dimension recorded and compared to the original diameter when the block was first delivered.
The dummy block will eventually take a set to a larger diameter during use. As the diameter
increases, blisters result. Operating life is decreased.
Machining the dummy blocks diameter and/or back face of the mandrel can extend its
useful life.

Loose Dummy Blocks

Where still in use, loose blocks should be regularly checked for aluminum build up; for
stress fractures; for nicks and damage due to mechanical problems; and for dimensional
tolerances. If blocks show damage, re-check alignment of the billet loader; and inspect the
dummy block handling system and repair as needed.

Clean-out Blocks
Regular use of clean-out blocks is recommended for both process reasons and to
improve dummy block life. A special block is built to a diameter larger than the dummy block;
recommendations range from 0.010 (0.25mm) less than container inside diameter, to 0.030
o
(0.75mm) larger than the fixed dummy block. The clean-out block must be preheated to 800 F
o
(425 C) before use.
Frequency of use varies
according to the plant, some pushing
the clean-out unit once every shift or
after alloy changes; and others never
using it. A more typical frequency is
once weekly.

Figure 3-5: Clean-out block

(Photo courtesy of Castool)

8
Ibid.

3-4
 Tooling - Chapter 3

Stem
Function. The stem (or ram) transmits the compressive forces from the main cylinder to the
billet, and so it must operate under compressive
stress without bending, breaking, or upsetting.
Material. The stem is constructed of hot work
tool steels, typically high in chrome,
molybdenum, and tungsten, or chrome,
vanadium, and molybdenum; A1S1 H-12 or H-13.
Heat Treatment. The stem is typically hardened,
quenched, and tempered to a hardness range of
429 - 477 Brinell (Rockwell C45-50). As the stem
is not normally subjected to extreme
temperatures, it is hardened primarily to provide
the necessary compressive strength.
Desired Material Characteristics. The stem
material is chosen to provide very high hardness,
high compressive strength, and very low ductility. Figure 3-6: Stem for threaded dummy
Causes of Damage. The stem may be block attachment (Photo courtesy of Lake Park
Tool)
damaged by:
Thermal Shock: The stem is very sensitive to
thermal shock. Heating or cooling the stem too
quickly will invite cracking.
Failure to Preheat: At room temperature the
stem is too stiff and brittle to be used safely.
o o
Preheat to 200-400 F (or 100-200 C) before use.
Never use direct flame use a slow soaking
furnace to preheat the stem.
Misalignment: Any misalignment may greatly
increase the stress concentration within the ram
and result in bending or breaking. See Chapter 2 Figure 3-7: Stem for bayonet-type
- Press Alignment. dummy block attachment (Illustration
courtesy of Castool)
Impact: Any sudden impact, such as striking the
container or malfunction of the dummy block,
may cause sharp stresses and eventually weaken the stem. These stresses may be relieved by
following the procedure described below.
Upsetting: Watch the face of the stem (the face where the fixed dummy block attaches) for
upsetting or deformation under load. When the stem diameter increases by 1/8-inch (3mm), or
when hairline cracks appear, the stem should be turned down and re-faced.
Work Hardening: Continued high-pressure contact with the dummy block may result in formation
on the surface of a thin layer of hard metal with many hairline cracks. To prevent these cracks
from expanding and propagating into the stem, periodically remove this work-hardened layer and
re-face the stem.
Fatigue: The stem, like all press components, is subject to fatigue failure in the form of tiny
cracks at stress concentration points. To relieve this condition, stress relieve according to the
following procedure:
o o o o
1. Heat the stem to 1000 F (540 C), at a rate no more than 100 F (55 C) per hour.
2. Hold at this temperature for one hour per inch (25 mm) of stem diameter.
3. Remove from furnace and air cool in still air at room temperature.

3-5
Tooling - Chapter 3

Frequency of stress relief of the stem should vary according to the history of the stem; suggested
intervals for normal conditions:

Compressive Stress - Range of Operation Suggested Interval for Stress Relief

180,000 - 200,000 psi 20,000 to 30,000 billets
160,000 - 180,000 psi 30,000 to 40,000 billets
130,000 - 160,000 psi 40,000 to 50,000 billets
100,000 - 130,000 psi 50,000 to 60,000 billets
Below 100,000 psi 100,000 billets

Precautions. To avoid damage and maximize life of the stem:

o
1. Preheat the stem before use. A slow heat-up is desirable. Temperatures above 200 F
o
(93 C) are adequate, but the temperature must be achieved through to the center of the
stem.
2. Avoid any direct flame impingement.
3. Avoid any water contact (unless anticipated and a special material chosen for this
application).
4. Check press alignment through the entire stroke of the ram.
5. Keep the ram clean and correct any visible damage. Re-machine to remove cracks,
upsetting, impact scars, or cuts, and stress relieve after each machining.
6. Avoid welding.
Preventive Maintenance Check List.
1. Keep the stem dressed at all times. Correct any visible damage as soon as possible by
machining to clean metal. Watch for small cracks, upsetting, impact scars, or cuts.
Stress relieve the stem after each machining. Never weld the stem.
2. Maintain good press alignment.
3. Check the end of the stem for upsetting, weekly or each time a fixed dummy block is
changed.
4. Check the end of the stem for work hardening, weekly or each time a fixed dummy block
is changed.
5. Stress relieve when required according to service and keep a record of stress relief.
6. Check its straightness with a straightedge.
7. Check the pressure plate to which the stem is mounted for damage, deflection, or
coining, by using a straightedge and feeler gauges; remove and re-grind flat if damaged.
The seat must also be clean.
8. The stem retention ring or other stem mounting devices must be properly tightened.
Check the stem and fixed dummy block often for signs of build-up or excessive wear.
Any contact forces are transmitted back to the main cylinder and may result in premature wear of
the main ram and bushings, and to the crosshead cylinders as well.
Maintain accurate drawings of all tools, for purchase or repair of replacement of spares.
Inspect spare tools when received (new or repaired) for condition and conformance to
dimensions dont wait until they are needed for use.
Store spare tools in a warm place, to minimize preheat time and avoid thermal shock.

Note: Stems are subject to sudden, catastrophic failure. See the photos in Chapter D Safety &
Environment, Figures D-2 and D-3.

3-6
 Tooling - Chapter 3

Container
Function. The container holds and supports the liner to prevent it from breaking under the
extreme forces of extrusion. The stress on the liner must be transmitted uniformly to the
container, so an accurate shrink fit is required. The shrink fit also induces compressive stresses
in the liner, allowing it ultimately to withstand higher stresses. The support must remain uniform
and continuous during the extrusion cycle; without it the elastic limit of the liner may be exceeded,
causing the liner to fail.
Material. The container is a forging, usually chrome-nickel-molybdenum or chrome-molybdenum-
vanadium steel, of SAE 4350 or SAE 4150 modified type.
Heat Treatment. The container is typically hardened, quenched, and tempered to a hardness
o o
range of 280 - 350 Brinell. Draw temperatures over 1000 F (540 C) are used to insure stability at
normal operating temperatures; no permanent softening of the container should be experienced
during normal service.
Desired Material Characteristics. The container
material is chosen to provide toughness, high
strength, and good ductility when warm.
Potential Causes of Damage. The container may
be damaged by:
Thermal Shock: Any sudden heating or cooling of
the container may cause stress cracking or other
damage to the container.
Excessive Heat: At elevated temperatures, the
container material will soften and weaken. At about
o o
1100 F (590 C) , permanent softening will occur and
the container may become unfit for further use.
Non-uniform Temperature: During operation,
uneven heat retention may result in a higher
temperature near the center of the container. The
hotter area will also be weaker and may yield under
the pressure of extrusion, causing a belly or
distortion of the diameter near the center. At lower
o o
temperatures (400-600 F/ 200-315 C) this distortion
may not be a problem, but at higher temperatures it
may become permanent and require re-boring of the
container. Figure 3-8: Container cracked
through hole for lifting eye. Container
Precautions. To avoid damage to the container: was also overheated.
(Photos courtesy of Lake Park Tool)
1. Preheat the container before use.
o o
2. Heat up slowly 100 F (55 C) per hour rate
of heat-up.
3. Avoid direct flame impingement.
4. Avoid welding. If welding is unavoidable,
follow this procedure:
o o
Preheat to 1000 F (540 C) before
welding
Weld
Anneal immediately after welding: heat to
o o
1600 F (870 C), soak, furnace cool, re- Figure 3-9: Alternative dove tail
heat treat. design for container lifting.

3-7
Tooling - Chapter 3

5. Avoid sudden cooling shocks.

6. Operate at the minimum container temperature consistent with good extrusion
practices.
7. Check thermocouples often.
8. Visually inspect the containers keyways periodically for cracks. Cracks found in the
bottom radii should be milled or ground to stop their migration into the container body.
9. Check the container for signs of relative movement in the container holder and repair
as needed.
Container Preventive Maintenance Check List.
1. Maintain good press alignment.
2. Check thermocouples at least weekly.
3. Check radii of keyways for cracks each time container is out of the press.
4. Check container hardness each time a new liner is installed.
5. Re-bore each time a new liner is installed.
6. Check for signs of relative movement in the container holder and repair as needed.
7. Check the faces of the container for nicks, scores, or metal build-up; clean and de-
burr, and readjust if needed.

For additional information on Container maintenance, see Extrusion Container

Care and Maintenance by James M. Pope, page 3-11.

3-8
 Tooling - Chapter 3

Container Liner
Function. The container liner resists the abrasive effects of the aluminum and oxides during
extrusion. High hardness at elevated temperatures is achieved at the expense of reduced
ductility, so the liner must depend on the support of the container to resist breakage.
Material. The liner is typically an A1S1 H-12 forging. It is a separate part from the container for
increased strength and so that it may be replaced when required by wear or damage.
Shrink Fit. The liner is subject to axial loading from friction between the billet and container, so a
shrink fit between the liner and container is used to prevent slippage between the components. A
9
shrinkage of 0.24% of the mantle ID is considered the maximum that may be used .
Heat Treatment. The container is typically hardened, quenched, and tempered to a hardness
range of 400 - 450 Brinell. A minimum of 2 draws is recommended, three where a final hardness
in excess of 477 BHN (50 Rc) is required. Each draw should be held at temperature for 2 hours
per inch of thickness, to insure proper soak.
Desired Material Characteristics. The container liner material is chosen to provide high
hardness, low strength, and very low ductility.
Potential Causes of Damage. The container liner may be damaged by:
Thermal Shock: The liner is very sensitive to any thermal shock. Any sudden or severe heating
or cooling of the container may cause breaking.
Lack of Support: The liner must be fully supported by the container by means of an accurate
shrink fit, or it will fail due to the tensile stresses of extrusion. If the container becomes hotter than
the liner, the shrink fit will be lost, resulting in failure.
Excessive Heat: At elevated temperatures, the liner material will soften, resulting in premature
wear-out. Lower operating temperature will result in longer life and lower costs.
Precautions. To avoid damage and maximize liner life:
o o
1. Preheat the liner before use. A long, slow heat-up (100 F/55 C) per hour is
recommended.
2. Be sure that the preheat procedure does not result in loss of the shrink fit.
3. Keep the liner warm when the press is not operating. As a minimum, close the ends of
the container to prevent cooling; advance the ram so that the dummy block is inside the
container bore. During longer delays, an electrical resistance heater should be placed in
the bore of the liner and the ends of the container covered.
4. Be sure that the container temperature never exceeds liner temperature enough to result
in the loss of the shrink fit.
5. Avoid any direct flame impingement.
6. Avoid any contact with water.
7. Avoid welding.
8. Keep the sealing face clean; avoid any accumulation of dirt, aluminum flash, lubricants, or
water.
Preventive Maintenance Check List.
1. Keep the bore from cooling when the press is not operating.
2. Keep the sealing face clean.
3. Do not operate with a cracked or broken liner.

9
Hahnel, Werner, and Herder, Manfred, Tool Steel and Design of Modern Containers for
Extrusion of Light Metal, Proceedings of 8th International Aluminum Extrusion
Technology Seminar, (2004)

3-9
Tooling - Chapter 3

Notes:

3-10
 Tooling - Chapter 3

Editors Note; The following paper was presented by Jim Pope, Special Projects Consultant to
Lake Park Tool:

Extrusion Container Care and Maintenance

by James M. Pope
st
Presentation at AEC Press Maintenance Workshop, Chicago, Illinois May 1 , 2002
Introduction. For those of you who work in an extrusion plant, that big hunk of steel referred to
as the press appears to simply sit there and effortlessly produce extrusions. To the contrary,
however, this machine is doing tremendous work, and very high stresses are being induced in all
the major components. During every push the tie rods are stretching, the main cylinder is bowing
and elongating, the front platen is bending, the stem is being compressed, and the container liner
assembly is subject to very high hoop stress forces. In this presentation we are going to examine
the container-liner assembly and how to obtain the maximum life from it.
Container-liner assemblies are considered expendable tooling and are therefore expected
to have a finite service life. Unfortunately they are also one of the most abused parts of an
extrusion press. Excluding the dies they are the only part of the press that has to do its work at a
constantly elevated temperature. The stem also gets hot, but it is normally half the temperature of
the container. Due to the combination of high stresses and heat under which it must perform it is
imperative that certain procedures be observed in order to get the maximum possible life out or
your container-liner assemblies.
Following are the most common causes of premature container or liner damage and failure:
Improper pre-heating
Over-heating
Fatigue cracks
Misalignment between the stem and the container
Misalignment of the press frame (tie rods)
Insufficient bearing area between the die and the liner face
Aluminum buildup on the face of the die
Caved platen pressure ring or caved platen
Pre-heating. Let us start with a review of the proper pre-heat procedures for a new or cold
container. The most preferred way to pre-heat a container is in a dedicated pre-heat oven with
accurate temperature controls. Lacking this piece of equipment some extruders use their aging
oven or die pre-heat oven. When using an extrusion aging oven for pre-heating, the container
o o
can only be brought up to 400 to 450 F (200 to 230 C). The remainder of the heating process will
have to be done in the press.
During pre-heating the container should be brought up to extrusion temperature of 700 to
o o o o
800 F (370 to 425 C) in increments of 100F (55C ). It is recommended to allow a 15 minute
minimum soaking time between raising the temperature increments when the container is below
o o o o
400 F (200 C). Once it is above 400 F (200 C) the soaking time should be 30 minutes between
raising the temperature increments. The container should have a thermocouple inserted in it to
verify the temperature. If the container is being pre-heated in the press there should be a
minimum of two thermocouples used, one to read the internal temperature at the liner and another
to read the temperature of the outside diameter. It is important to monitor the outside diameter
temperature in order to not over heat and anneal the container. If a bore heater is being used in
tandem with the press heaters, care should be taken to balance the heating between the two
systems. A bore heater should never be used as the only source of pre-heating a container as
there is a great risk of splitting the liner and container. A container should never be put into
o o o o
production under 650 F (340 C) with 700 F (370 C) being the recommended minimum.

3-11
Tooling - Chapter 3

Over heating. Evidence of over heating is scaling or erosion of the container outside diameter.
In most instances of over heating the container has also lost its proper hardness. In extreme
cases the entire container will be bowed.
Annealing of steel is a basic function of
time versus temperature. The annealing
temperature for H-12 and H-13 steels starts at
o o
1100 F (590 C). However prolonged use at lower
temperatures has the same effect. Therefore it is
of utmost importance to limit the temperature of
o o
containers to 750 F (400 C) or less. Overheating
can usually be attributed to inadequate temperature
controls or in some cases failed controls. Very few
presses built prior to the late 1980s had more than
a single thermocouple to monitor the container
temperature. Due to increasing complaints about
short container life, the press builders began to
install a second thermocouple to monitor the
temperature on the outside of the container. This
o
controller was normally set at 900 to 950 F (480 to
o
510 C) and would shut off the container heating
system if the container reached this temperature. If
your press does not have an over-temperature
protection thermocouple one should be installed as
soon as possible.
Today all new presses are being built with
four to six zones of temperature controls. Another
feature now being used in containers is air cooling
of the liner in the front half next to the die. This is
being done as a production enhancement, however
it has also contributed to keeping the container in Figure 3-10: Container with crack through
the desired temperature range. The zone heating keyway, probably caused by overheating.
and liner cooling are also features that are now A larger radius may help eliminate this
being incorporated into retrofit packages for older problem
presses. (Photos courtesy of Lake Park Tool)

Fatigue Cracks. Cracking begins to occur in

containers that have been in service long enough to begin to lose their hardness. Most cracks
start to show in keyways and this is due to several factors. A loss of hardness is the most
common reason and this is due to over heating. Another reason is improper machining. No
sharp corners should exist in internal corners. They should be machined with at least a .125 inch
(0.30mm) radius. Sometimes the container design can be modified to eliminate keyways being
cut the entire length of the container. If cracks start to show up around lift holes or thermocouple
holes this again is usually due to a loss of hardness and the resultant bowing. Once cracking has
started to occur, the containers useful life is basically over.
Misalignment Between the Stem and the Container. Some 15 to 20 years ago, before
widespread use of fixed dummy blocks, container alignment was not a real critical component of
extrusion press operation. As long as the container was close to being centered on the die and
the billet would go into the liner bore and the stem was close to being in line with the liner bore,
this was good enough as the loose dummy blocks of that era had excellent self aligning
properties. Today, with almost universal use of fixed dummy blocks, accurate container alignment
is critical to the operation of an extrusion press. Some fixed dummy blocks are designed to float
or adjust for small amounts of misalignment. However the ability for dummy block self alignment
should not be an excuse for not having precise guiding of the container and good alignment
adjustment capability. Misalignment between the fixed dummy block and the liner bore can cause
chips to be cut out of the entry end of the liner face. Longitudinal score lines on the inside of the
liner bore are also an indication of the container bore not being concentric with the press
centerline.

3-12
 Tooling - Chapter 3

Misalignment of the Press Tie Rods. If the tie rods have lost their pre-stress or the cylinder and
front platens are out of tram this could cause the container to shift away from the press centerline
during extrusion. This condition would cause longitudinal scoring inside the liner bore. This
condition cannot be detected by simply checking the clearances between the stem and liner bore
when the press is at rest as the container shifts out of alignment only after pressure has been
applied. A pre-stress and tram check of the press is required to find and correct this problem.
Insufficient Bearing Area Between the
Die and Liner Face. To prevent flashing
of the aluminum between the die and the
liner, a positive clamping force is applied to
seal the container against the die. This
force is greatly augmented at the beginning
of extrusion by the force of the press. This
is due to a good percentage of the press
tonnage being transmitted into the
container due to friction of the billet against
the liner bore. This force diminishes as the
billet is extruded until a point is reached
whereby a reverse force is actually induced
into the liner. One would think that it would
be easy to calculate the force of the liner
on the die and allow for sufficient bearing
area. However it is not so simple.
The sealing pressure exerted on
the die by the press container shift
cylinders is easy to calculate. The
additional forces emanating from the press
are very difficult if not impossible to
determine as they vary with the pressure
required to extrude each billet and are
constantly diminishing as the ram
advances through the container. To
reduce or prevent die indentation into the
liner face, ideally there should be a
minimum of 1 inches of bearing area
around the liner. This means that a 7-3/8
inch bore liner should have a 10 3/8 inch
die face. In the real world this does not
usually happen due to the costs of the
larger dies. Most presses with a 7-3/8 liner
bore have die faces of only 8-1/2 inches
and sometimes even less. This is the
reason that the die coins itself into the face
of the liner and it must be periodically faced
off. When a container is relined a
minimum of inch but no more than
inch should be allowed for future facing. In
no case should the liner be allowed to
become flush with the container.
Aluminum Build Up on the Face of the
Die. The build up of aluminum on the face
of the die will cause flash outs and damage Figure 3-11: Liner with badly coined face,
to the face of the container. The internal probably due to insufficient contact surface
bore of the liner could also experience between die and liner face.
(Photo courtesy of Lake Park Tool)
scoring if the build up is of sufficient
thickness and is unevenly distributed

3-13
Tooling - Chapter 3

around the die to such an extent that it forces the container off centerline. The dies need to be
kept clean and free of this buildup. The buildup of aluminum is mainly caused by the butt shear
not severing the butt cleanly off the die. This can be the fault of the shear in that its design is not
conducive to clean shearing. Another contributing factor to aluminum buildup is the fact that in
most presses the die tooling is not held in position securely enough to prevent moving during
shearing. Spraying the face of the die is one remedy but not a cure. A more long term solution is
to install a butt shear that has a well guided blade carrier and a sharp cutting angle on the shear
blade itself. For the shear to operate most efficiently a positive die hold-down that is hydraulically
activated is required. This device will hold the die tooling securely in place during shearing.
Caved Pressure Ring and/or Caved Platen Seat Behind the Ring. If the die support ring in the
platen or the platen itself is dished or caved in, this will cause the container to move off centerline
and cause the same problems as die build up. This condition will also cause numerous die
problems, however this subject is not part of this presentation.
Inspection before relining. When a container does need to be relined, a thorough inspection of
the unit in your plant could save you the cost of shipping a heavy piece of scrap to a reline shop.
If the container has extensive cracks in the keyways or in lift holes or in thermocouple holes or is
annealed and bowed, it is probably not worth relining. New containers made from 4340 forged
steel are heat treated to 34-38 Rockwell C scale. If H-13 is used for the container they are heat
treated to 38-42 Rockwell C. The liners are mostly made from H-13 and are heat treated to 44-
48 Rockwell C. If A-286 or Inco alloys are used for the liners they are solution aged to 40-44
Rockwell C.
In summary there are a number of corrective measures that can be taken to get the most
life possible out of your containers and liners. Understanding the cause of the problems will allow
you to take the proper corrective measures that will extend the life of your container/liner
assemblies.

3-14
 Tooling - Chapter 3

Recent Improvements in Container Design

Container Heating. In years past, most
containers were heated by electric
heating elements located outside the
container, in the container housing
(Figure 3-12). However, the need for
more uniform container temperatures as
well as improved container life led, some
years ago, to development of systems to
heat the container from inside the mantle
(Figure 3-13). In the case of external
heaters, it is possible that the heat
source combined with the heat from
extrusion may cause the mantle to
10
overheat and become annealed (Figure
3-14). Figure 3-12: Container with external heating
elements.
Another improvement designed
to improve temperature uniformity is the
change to multiple zones of control.
Newer presses often offer 4 or 6 zones
of control, divided into 2 or 3 zones
axially, as well as separate zones top
and bottom (Figure 3-15).
An important requirement is to
provide thermocouples for each zone
and also for the mantle itself, to prevent
over-temperature and annealing.
Note that axial variations in
temperature along the liner, caused by
heat loss at the container end faces, may Figure 3-13: Container using heaters inserted into
result in a higher temperature near the the mantle.
center and result in bulging or barrel
effect.
Container Cooling. Most new presses
now offer optional cooling of the container liner, by means of passages for compressed air to
circulate around the container liner. Air flow is typically controlled by PLC. Combined with multi-
o o
zone heating control, PLC controls may maintain liner temperature within a range of 10C (18F ).
FEM Analysis is an essential tool for analyzing the sum of stresses in the container and liner,
including thermal stresses. Figure 3-17 illustrates a FEM analysis of a container mantle and liner
with cooling, indicating increased stress levels at the cooling grooves. Similar analyses allow
design improvements to reduce stress levels and improve container life.

10
Hahnel, Werner, and Herder, Manfred, Ibid.

3-15
 Tooling - Chapter 3

Figure 3-14: Influence of external vs. internal Figure 3-15: Various multi-zone heating systems
(Illustration courtesy of Kind & Co.)
heating systems. (Illustration courtesy of Kind & Co.)

Figure 3-17: Finite element analysis of container

Figure 3-16: Container cooling grooves during extrusion cycle, with cooling (from Wieser,
(Illustration courtesy of Kind & Co.) footnote 11)

11,12,13
Further references on modern improvements in container design are listed in the footnotes .

11
Wieser, Volker; Sommitsch, Christof; Haberfellner, Kurt; and Lehofer, Paul; New
Developments in the Design and Production of Container Assemblies, Proceedings of
8th International Aluminum Extrusion Technology Seminar, (2004).
12
Van Dine, Dennis, Thermal Control of the Extrusion Press Container, Proceedings of 8th
International Aluminum Extrusion Technology Seminar, (2004)
13
Robbins, Paul, Superextruders: Improving Container Life Through Temperature Control, Light
Metal Age Magazine, April 2003, Page 44.

3-16
 Tooling - Chapter 3

Spare and Replacement Tools

The following recommendations are offered for maintaining spare tools such as container,
liner, ram, etc.:
Maintain accurate drawings of all tools, for purchase or repair of replacement of
spares.
Inspect spare tools when received (new or repaired) for condition and conformance to
dimensions.
Store spare tools in a warm place, to minimize preheat time and avoid thermal shock.

Dies & Back-up Tooling

While not normally considered a part of press maintenance, proper care and handling of
dies and support tooling are critical to smooth press operation. For example, in plants where the
outside dimensions of the tooling stack do not adhere to strict tolerances, excessive maintenance
to the butt shear and die changer will result.
Additional information on maintenance of dies and back-up tooling is contained in the
following article, Preventive Maintenance of Extrusion Tooling, by Gary Dion, Nova Tool and Die,
Inc.

Die and Tooling Cleaning

Dies, dummy blocks, and other tooling must periodically be cleaned of aluminum build up.
The use of sodium hydroxide for die cleaning, rather than employing emery paper, can
result in a decrease in extrusion pressure, permit lower temperatures, higher speeds, and less
metal pickup, partly because of ther superior finish on bearing surfaces. Solutions of 10% to 25%
are customary. When tanks are employed, standard solutions are the rule, but a higher
o o
concentration is necessary if wiped on. Tank solutions are heated to about 140 F (60 C).
Thorough rinsing is necessary following cleaning to guard against caustic effects on the
aluminum. Precautions against excessive breathing of fumes as well as direct contact with the
skin, particularly the eyes, should be taken. Potassium hydroxide also is used for cleaning but the
14
cost may be prohibitive. Cleaning caustics may stain extrusions .

14
From Extrusion Dies and Tooling Manual: Recommended Handling and Maintenance, AEC
(Aluminum Extruders Council), www.aec.org.

3-17
Tooling - Chapter 3

Note: The following paper provides useful information about the inspection, handling, and
preventive maintenance of extrusion dies and back-up tooling. It was first presented by the author
at the AEC Press Maintenance Seminar, in Chicago, May 2, 1995, and is reprinted here with his
permission.

PREVENTIVE MAINTENANCE OF EXTRUSION TOOLING

by Gary Dion
Extrusion Consultant (former owner of Nova Tool and Die)

How does preventive maintenance relate to extrusion tooling? From surveying many
extruders it was found that proper preventive maintenance of tooling plays a very important role in
the success of an extrusion operation. Improper maintenance can and most likely will result in
poor performance in one or more of the following areas:
Pounds per hour of aluminum produced
Extrusion die life
Die and support tooling breakage
Press downtime which is very expensive
Maximizing die life while minimizing weight per foot
Even though with dies you dont check the oil level, inspect roller bearings, or monitor
wear of motor brushes, there are many aspects of the extrusion tooling to be checked and
maintained properly. As the Fram oil filter man says, You can pay me now, or pay me later, and
in some cases a whole lot more! The possible checks and maintenance steps for extrusion
tooling can be broken into four major categories.
1) Incoming inspection of dies and tooling
2) Handling of dies and tooling
3) Inspection of dies and tooling after use
4) External features of dies and tooling
Incoming Inspection
It is not good manufacturing practice to put a bad die in the press and waste valuable
press time, labor, billet, etc. Of course this probably doesnt happen, at least not very often. But
what are you currently monitoring to maximize your presses' productivity? Could you be
monitoring more? Listed below are many of the checks extruders have implemented to achieve
the highest quality product at the most productive rate.
1) Proper tooling identification. Die, suffix, backer, bolster and feeder plate numbers are
important. If the wrong number is on the die, it could be set up and run incorrectly, causing major
problems. Also, date and vendor ID are a good idea.
2) Check for metal chips or shavings from manufacturing. These tiny metal shavings will
hide in the relief area or bearing area of the die and show up in the extruded product or possibly
create die lines.
3) Check die and related tooling for proper Rockwell. Even though most die makers
thoroughly inspect for this, it's not impossible to vary by a few Rockwell C points.
4) Tool diameter, thickness and step dimensions. Its better to be safe than sorry. Checking
tool dimensions will prevent tools from being stuck in die rings, or being loose, allowing for

3-18
 Tooling - Chapter 3

misalignment and/or aluminum seepage into undesired space, butt shear from hitting the tooling
face, etc.
5) Pinout of die openings. This will tell you how much tool deflection you are getting on your
tooling, which is extremely useful for future dies. It will give accurate information for zeroing in on
minimum weight per foot, allowing for maximum poundage from each die.
6) Support tooling clearance. Check for interference of backers, bolsters, sub-bolsters and
platen opening. It is better to grind in some clearance which will decrease the possibility of
plugging and/or possibly breaking the assembly.
7) Proper support on backer, bolster. Make certain that the backer and bolster have the
proper support to eliminate as much tool deflection as possible, and minimize the chance of tool
breakage.
8) Proper exit clearance. Check the step behind the bearing for proper clearance. There
should be a minimum step on critical tongues, screwbosses, etc. Too much clearance can cause
a die to cave and run incorrectly. Approximately 0.040" (0.10mm) is considered normal.
9) Proper die support. On tongues it is desired to have maximum support for best results. Zero
degrees of back taper is usually desired on areas with small or long tongues and screw bosses.
10) Bearing finish. Check die bearings for:

Wire EDM lines

Scratches from files, gage pins, or emery paper

EDM pits

Nicks from handling, shipping

Burrs on exit side of bearing from orbital EDM or milling relief
It would be better to catch one of these items and correct it prior to sampling or attempting to run
the order. How many times have you pulled a die because of die lines?
11) Bearing flatness, squareness. Not enough can be said for the importance of square and
flat bearings. A precision square needs to be used to confirm that the bearings on both the die
and mandrel are flat and square.
12) Bearing transitions. Proper placement and smoothness of bearing transitions are critical as
this is another area which can cause die lines. Improper placement of transitions will also cause
the die to produce a product that is not dimensionally correct.
13) Maximum port/spreader/feeder plate openings. These items if made too close to the
container opening will cause poor metal finish. Contamination will enter the ports from the skin of
the billet and be extruded into the profile. Poor metal quality will also result if the profiles are too
close to the container size on a solid die.
14) Proper die alignment and handling features. Inspect dowel pins, keyways, bolster pins,
etc., for proper position and sizes.

Handling of Tooling
Dies and tooling are the heart of your finished product. Bad dies, bad extrusions. It's that
simple. Dies should be treated like jewelry, not blacksmith anvils. This slight exaggeration was
not meant to insult the die handlers but to stress a point. Too often dies are not treated with
enough care and are damaged due to carelessness. Make every attempt to keep dies off the
floor as dirt in the tools will result in poor metal finishes. Care must be taken when removing
assemblies from the die rings. A die separator would be recommended rather than a big
hammer, even if the hammer is aluminum. Too many tongues, screwbosses, etc., have been lost
to the blow of a hammer. Careless banging of tooling together can damage bearing surfaces and
mating surfaces.

3-19
Tooling - Chapter 3

Inspection of Tooling After Use

After the tools are used to extrude the required product and have been run through
caustic, a careful inspection of all components is recommended. Putting a damaged tool in
production is obviously not a desirable practice. Here are a few areas to check for:
All Dies:
After each extrusion run, all dies should be inspected for the following conditions:
1) Wash-out on bearing surface. Washed out bearings can cause poor metal finish. Polishing
the wash-out from the bearing will eventually cause an overweight condition. It might be time to
consider ordering a backup die for stock or future orders.
2) Cracks on tongues and critical areas. Breakage is on the horizon. This can waste valuable
press production time.
3) Weight per foot. Monitoring this factor will prevent you from giving extra metal to your
customers.
Hollow Dies:
Hollow dies should be inspected after each run for the following conditions:
1) Check for cracked webs, armpits or weld chambers on the housing. Some hairline
cracks are normal, but excessive cracks will lead to complete tool failure.
2) Flatness of housing face, die face. A caved entry is a sign of tool fatigue and replacement
might be considered. This can cause die and mandrel bearings to be misaligned resulting in poor
metal quality.
3) Rockwell hardness of tool components. Low Rockwell hardness of dies can cause poor
metal quality and tool failure. Recommended Rockwell C is usually 47-49. Sometimes tools can
be re-heat-treated to avoid premature failure.
4) Tapered sealing area on die and spider assemblies. Check for nicks on the outside taper
which could damage the die ring.
Solid Dies:
Solid dies should be inspected after each run for the following conditions:
1) Flatness of die, backer. If the die or backer isn't flat, more than likely the metal isn't hitting
the bearing surface correctly and you are losing control of the metal flow. It also is allowing the
die to deflect too much which contributes to poor production and bad material. Caved tooling
could be a sign of improper or cracked support tooling (backers, bolsters).
2) Cracked corners on die openings. This could result in burrs or die lines on the extruded
product. This also could be a sign of poor or cracked support tooling.
3) Cracked backers. Cracks in backers will cause metal to run poorly and can result in
premature failure of dies.
Bolsters and Support Tooling:
Support tooling should be inspected on a regular basis rather than only when a profile runs poorly.
Check for the following conditions:
1) Flatness. Bolsters and sub-bolsters which are not flat will cause problems when extruding.
This will allow for the die to deflect too much. It is also extremely important when running wide
profiles or profiles with critical tongue conditions. Many times bolsters, etc., can be reground flat
and even re-hardened if necessary.
2) All surfaces clean and free of aluminum build up.

3-20
 Tooling - Chapter 3

3) Rockwell. Periodically check the Rockwell to insure the tool isn't being annealed over time
being exposed to temperature changes. The ideal Rockwell is between 42 and 46 RC.
4) Inspect for cracks. Small cracks in the corners eventually become big cracks, which could
cause the whole tool stack to fail, including the die and backer. Replacement should be
considered soon.
5) Nitrogen Inlets. N2 couplings and inlets must be kept clean to allow free flowing of liquid or
gas nitrogen. Also, this prevents dirt from passing through to the metal.
6) Nicks. Check for nicks caused by handling the tooling. It's easy to bang these large tools into
other pieces of steel or tooling. Nicks will keep other tooling from sitting flat and could cause
damage.
7) Lift holes. Make sure threaded lift holes are free from foreign materials which could prevent
the eye-bolt from being threaded in completely. This decreases the chance for accidentally
dropping the bolster, thus damaging the tool and even possibly injuring someone.
Platen Pressure Ring:
As true with other support tooling the platen pressure ring needs to be inspected periodically.
Check the following items:
1) Flatness. Check for an impression approximately the size of the bolster or sub-bolster. This
means the ring is wearing and needs to be considered for replacement.
2) Clean. Free from aluminum build-up.
3) Cracks. If the pressure ring is cracked you can be assured the whole tool stack is deflecting
which will eventually cause other tooling components to fail.
Die Rings:
The ring which contains the die assemblies also needs to be regularly maintained:
1) Sealing areas on tapered die rings. The tapered area on die rings which hold spider
assemblies must be kept free of nicks and aluminum build-up. It is also important to monitor the
sealing area for impressions from the assembly. This could be an indication that the spider
assembly is improperly sized. This will also allow unwanted aluminum to build up between the
ring and assembly.
2) Sealing areas on step die rings. Again check for metal build up. Inspect for chips of the ring
missing which could allow aluminum to squeeze between the ring and die components resulting in
difficulty to disassemble. Check the step dimension to insure that the die doesn't protrude too far,
allowing the butt shear to hit the die. This could also cause the die to leave an impression on the
container liner which could cause flashing.
3) Lift holes. Make sure threaded lift holes are free from foreign materials which could prevent
the eye-bolt from being threaded in completely. This decreases the chance of dropping the
assembly, damaging the tools and even possibly injuring someone.
4) Keyways. Worn keys can cause misalignment of the die and backer assembly. This could
result in clearances not being correct and plugging of the tool. Replace the keyways periodically
for maximum reliability.
5) Nitrogen hookups. If gas or liquid N2 is introduced through the die ring make sure hookups
and inlets are in proper working condition, clear and free from buildup. Check sealing area for
damage or wear.
Die Carriers, Die Slides:
Over the course of multiple die changes the die slide is prone to wear and tear. Proper inspection
and upkeep will help keep the dies in their proper position during the extrusion process, and keep
the die and ring from being damaged by the shear. Routinely check for the following items:
1) ID of horseshoe. Check for proper fit to die rings.

3-21
Tooling - Chapter 3

2) Build up of grease, dirt, or aluminum. This will cause improper alignment of tooling.
3) Horseshoe bolts. Assure tightness of these bolts periodically.

Other steps to take for optimizing press and tooling performance

Organization of dies and support tooling with easy access will help prevent the wrong
support tool from being used. Location numbers can even be used to organize the tools.
Once the die, whether it be a hollow or a solid, is cleaned, inspected and ready for
storage, it is recommended that the internal areas of the die be coated for protection from rust,
dirt, etc. These areas would be die bearings, pockets, ports, etc. On some complex profiles
some extruders even leave the die full of aluminum if the die performed well on the last run. One
of the more popular coatings is an aluminum spray which doesn't affect the metal on the next run.
A good high temperature anti-seize compound should be applied to all bolts used in the
die assemblies. Anti-seize also should be used on replaceable parts such as pincores and
mandrels which fit into pockets. This will help during the replacement process.
If you have more than one press in which a die assembly can be used, it is important that
care is taken when making tool stack setups. Make sure the proper bolster, sub-bolster, spacer
rings, etc., are used to make up the proper tool stack. It's easy to miss the proper thickness and
plug the first billet, creating unwanted downtime. Also check for proper clearances all the way
through the tool stack.
Press alignment plays an important role in the production and quality of metal. There are
various means of checking press alignment, and it should be checked and corrected weekly.
Developing a re-nitriding program will help maximize die life and press productivity.
Through such a program one should be able to accurately predict the amount of billets to run of a
certain section, rather than waiting for a die line or something to show up on the metal. Excessive
tool wear and bearing washout can be reduced through proper monitoring.
On hard pushing dies the practice of using a short, and sometimes hotter billet is
recommended to start the die on the first billet. This will reduce the risk of damaging the die.
Insuring that dies and support tooling are preheated properly is of critical importance.
Cold bolsters and other support tooling can crack during use, and can also draw too much heat
out of the die assembly.

Summary
Although some of the items covered in this article might seem a little elementary, it is
important to make sure as much prevention is considered with extrusion tooling as possible.
Anytime a problem or potential problem is detected before trying to extrude, you can save
valuable press time, and even prevent major tool failure.
Gary Dion

3-22
 Tooling - Chapter 3

Minimizing the Occurrence of Flared Billets in

Aluminum Extrusion Presses

A common problem of aluminum extrusion is flared or mushroomed billets --- in which the
aluminum spreads out between container and die instead of passing through the extrusion die.
Flared billets result in lost production time and also scrap. Occurrence of more than one or two
flares per month is considered excessive.
Mr. Domenico Bertoli of SEPAL, a well known extrusion expert, has recommended steps
which can be taken to reduce the occurrence of flared billets:
1. The sealing surface between container and die/die ring must be clean and smooth. The butt
shear blade must be in good condition and designed for a smooth, clean cut. Clearance must
be adjusted properly, typically 0.020 inches (0.5 mm) for smaller presses, up to 0.125 inches
15
(3.2mm) on larger presses . Proper release agents sprayed automatically on the shear
16
blade will also help .
2. It is also important to maintain the correct specific sealing pressure on the surface between
container and die/die ring. Specific pressure is defined as the sealing force divided by the
17 2
contact surface area. The minimum value desired is 2.5 kg/mm , which converts to 3,550
pounds per square inch.
To compute the specific sealing pressure:
Calculate the sealing force. For each sealing cylinder, the effective area is the area of
18
the bore minus the area of the rod . Multiply this net area by the sealing pressure and by
the number of sealing cylinders (typically two, occasionally 4). The result is the sealing
force.
Calculate the area of the contact surface. This area is the difference between two
circles. The smaller circle is the container inside diameter, which is usually about 0.375
inches (9mm) larger than the nominal billet diameter. The larger circle varies with
containers but should be the outside diameter (OD) of the container liner, assuming that
the liner extends slightly outside the container forging as it should. Subtract the smaller
area from the larger to determine the contact area.
Divide the force by the area. Divide the sealing force by the sealing area to determine
the sealing specific pressure.
If the specific sealing pressure is too low, indicating poor sealing, there are two ways to
increase it:
1. Increase sealing pressure. This is subject to the capabilities of the hydraulic system
and the pressure ratings of the hydraulic cylinders and piping. Do not exceed capacity of
cylinders.

15
Follow press manufacturers recommendations.
16
For additional information contact Amcol Corporation, 21435 Dequindre, Hazel Park MI, tel 248-
414-5700, fax 248-414-7489, www.amcolcorp.com.
17
Mr. Alan Castle of Service Aluminium recommends values up to twice this value, but cautions
that the contact area between liner and die must bear additional force during the early part
of extrusion, when the friction force is added to the sealing pressure. He cautions to be
sure that the contact area is not reduced so much that it will cause the die to deflect or
unduly; he especially advises that the liner not contact the die ring, which is usually
unsupported and so may deflect too much under this force.
18
For presses with platen-mounted sealing cylinders. A few presses such as front-loading
presses, have direct-acting cylinders, mounted on the main cylinder, in which case the rod
area is not deducted.

3-23
Tooling - Chapter 3

2. Reduce the contact area. Since the inside diameter of the container liner should not be
changed, the outside diameter may be reduced. First calculate the desired outside
diameter, based on the area needed to give the correct specific pressure. Then at that
o
diameter introduce a slight (7 ) bevel at that point to limit the contact surface. (See
illustration.)

Sample Calculations:
Sealing force: assume 2 cylinders, 9 bore x 6 rod, 2500 psi
2
Area = d /4
2 2
Total area = 9 /4 = (3.14159)(81)/4 = 63.62 in
2 2
Minus rod area = 6 /4 = (3.14159)(36)/4 = 28.27 in
2
Effective area = (63.62 28.27) x 2 rods = 35.35 in x 2
2
Force = 2500 psi x 70.70 in = 176,750 pounds

Contact area: container ID 8.375, liner OD = 12.5

2 2
Total area = 12.5 /4 = (3.14159)(156.25)/4 = 122.72 in
2 2
Minus ID area = (8.375) /4= (3.14159)(70.14)/4= 55.09 in
2
Effective area = 122.72 55.09 = 67.63 in
2
Specific pressure: Force/area = 176,750/67.63 in = 2613 psi (too low)

To calculate a suitable sealing area:

Assume no change in sealing force = 176,750 pounds

2
Desired area = 176,750 3550 psi = 49.79 in
2
Plus area of liner ID = 55.09 + 49.79 = 104.88 in
2 2
Using Area = d /4 = 104.88 in
2
d = 104.88 x 4/ = 133.54

d = 11.56 inches

Therefore, mark the face of the container liner at 11.56 and bevel the face outside that point.
(See Illustration)

3-24
Tooling - Chapter 3

3-25
Tooling - Chapter 3

Notes:

3-26
 Tooling - Chapter 3

Lubrication of Extrusion Press Tooling19

Why Lubricate Press Tools?

Because hot aluminum and many of its alloys tend to stick to hot steel and its alloys,
lubrication of press tools is standard operating procedure when deforming hot aluminum. Once the
process of aluminum build-up on tool steels begins, it continues until the build up eventually affects
the machine process. This eventual build up of aluminum can be avoided in one of two ways:
A. Lubricate as Needed - Before or after sticking of metal to the tool steels has begun, apply a high
temperature grease, oil, or other parting compound to the point of build- up with a swab or similar
tool so as to penetrate the metal-to-metal contact point and separate the build up from the tool
steel. This process is often creates smoke, flames, and soot. In addition, if lubrication is not
applied at the proper time, build-up will lead to sticking that eventually causes machine wear,
premature misalignment, and eventual
downtime (See Figure 3-18).
B. Lubricate as Preventative
Maintenance - Prior to metal build up
occurring, automatically apply a high-
temperature water-based solution to Figure 1: Left unlubricated, tools build
the points of aluminum/steel contact at up metal that eventually leads to
regular intervals (i.e., with every billet, problems.
with every other billet, etc.). Using the
proper chemicals, applied with well-
engineered spray equipment, this
process goes virtually unnoticed while
at the same time reducing or
eliminating metal build up and thus
allowing for uninterrupted press
operation. Figure 3-18: Left unlubricated, tools build up metal
that eventually leads to problems.
It is not hard to see that in todays
world of quality directives and automation
implementation that the latter is the best solution, as long as the cost of use and implementation does
not exceed the potential benefits. We will first review the recognized advantages of automatic
lubrication of these tools and then discuss a variety of items relating to the implementation of
automatic lubrication.

Automatic Lubrication of Press Tools

Automatic press tool lubrication can be used to improve extrusion press efficiency and
safety. Specifically, the use of automatic lubrication for butt shear blades, log shear tools, fixed
dummy blocks, and billet scalpers, is now in common use; other areas such as die ring/container
rings and piercing mandrels are under consideration.
Automatic lubrication was initially not well received, because the early equipment and
chemical designs were not always suited for the rough environment associated with an extrusion
factory. Additionally, extrusion presses are expected to be clean and the early systems were messy
to operate. The technology has been updated to a point that has been time-tested to be effective and
usable within this rugged working environment and within the cost parameters of this very competitive
industry. Implementation of automatic lubrication requires proper system design, installation,
operation, and maintenance, so as to insure long-term success.

19
Dyla, James, Protect Your Press Tools, Proceedings of 7th International Aluminum Extrusion
Technology Seminar, Vol II, (2000), p. 277-282.
3-27
Tooling - Chapter 3

Advantages of Automatic Lubrication

The advantages of automatic lubrication of press tools as an integral part of the aluminum
extrusion process are now recognized by aluminum extruders and equipment suppliers to the
industry. This is because it is not possible to leave these tools unlubricated when the tools or
machine become worn and/or misaligned. Used properly, automatic lubrication will:
1. Significantly reduce press downtime due to hang-ups, sometimes by a factor of ten (10) or
more, when compared to less predictable
manual methods.
2. Provide better cuts for improved billet-to-
billet contact, potentially reducing air
entrapment (See Figure 3-19).
3. Eliminate manual lubrication by press
operators, allowing them to focus their
attention on other parts of the process.
Also, this is one more step towards the full
elimination of operator intervention into the
hazardous extrusion press working
environment.
4. Clean up the smoke and soot associated
with graphite and oil chemicals used with
manual methods, providing a cleaner and Figure 3-19: Proper lubrication of the butt
safer production environment. shear results in a clean and complete
removal of th butt from the die.
5. Make the lubrication process predictable,
adjustable and able to be monitored for a
more quality-oriented process and a method for continuous improvement.
The technology is proven to have benefits, with the simplest and most cost effective
application being lubrication of the butt discard shear and log shear cutting blades. Thus, we can
now detail chemicals and equipment that have been engineered specifically for application to press
tools, how they are implemented, and the potential pitfalls in their use.

Fluids for Non-ferrous Extrusion

A variety of chemistries have been used for manual and automatic spray lubrication of tools,
such as graphite/water suspensions, boron nitride suspensions, fatty oil mixtures, water carried
soaps, inorganic solutions, organic polymer dispersions, and other specialty blends. Simple graphite
and boron nitride dispersion chemistries have shown to perform most effectively in this area;
however, these dispersions have proven hard to apply consistently and safely. Water carried soaps
and inorganic solutions have proven to be most easily applied, yet performance characteristics can
be limited. Organic polymer dispersions and other proprietary blends seem to provide a good
balance of performance and applicability.
The following list details the ideal characteristics for a universal fluid for all applications in
aluminum extrusion:
1. Non-flammable - Any fluid to be sprayed around an extrusion press must be non-flammable
and such that the remaining lubricant cannot be easily ignited. The Flash Point and Auto Ignition
Temperature found on a Material Safety Data Sheet (MSDS) should be not applicable or not
burnable and the National Fire Protection Association (NFPA) fire rating should be zero (0).
2. Not Detrimental to Extrusions - The litmus test for lubricants used in and around the extrusion
process is to spray the product into a die and on the dummy block for several billets and follow
the product through extrusion, fabrication, and finishing. A product that is detrimental to the
extrusion process cannot be considered a viable alternative.
3. Lubricating at High Temperatures - As the primary function is to provide tool lubrication and
release properties, the fluid must keep the hot aluminum from sticking to the tool steel at the
3-28
 Tooling - Chapter 3

pressures and temperatures associated with the extrusion process. Manual spray methods are
used to help simulate automatic methods as a test procedure to insure the success of automatic
methods (See Figure 3-20).
4. Good Wetting Properties on Hot
Tool Steel - Water carried fluids
have a tendency to bounce off hot
surfaces; the water carried fluid
must therefore stick to the tool
steel and allow for evaporation of
the water as a method to provide
momentary surface cooling. Once
the water has evaporated from the
spray applied fluid, the remaining
lubricant must be able to spread
out onto the hot surface to form a
light, uniform film over the area
onto which it is sprayed. This
allows for the fluid to reach Figure 3-20: Manual spray wands are used for testing
surfaces that cannot be directly and production application of spray fluids.
sprayed.
5. Water Miscible - A well-designed water-miscible lubricant can be easily blended with tap water
to form a light-viscosity solution, which can then be spray atomized. Once mixed with water it
must be stable so as not to separate and it must be resistant to biodegradation from bacterial
contamination, which is often found in tap water. Equipment designs are simpler and application
is more predictable with water-miscible chemistries. If the product is unstable in water, yet
mixable with water, equipment designs are available for continuous mixing.
6. Safe to be Sprayed - Many chemicals cannot be sprayed as they will cause bodily harm if
inhaled or absorbed through the skin. Be sure these types of chemicals are not atomized in the
working environment.
7. Overspray Easily Cleaned Up - Overspray will occur when atomizing a fluid to a remote
location; therefore, be sure that the remaining overspray is easily removed with warm water or a
light duty industrial cleaning solution.
Lubricants have been developed that meet all of these parameters if the surface to be coated
o
is normally below 400 F; however, the technology in the area of high temperature coatings applied to
o
surfaces which exceed 400 F is still under development. The butt and log shear blades are normally
o
well below 400 F at the time of application and thus this is an area which is in common use and very
successful. Dummy blocks, billet scalpers, and piercing mandrels are much hotter and the fluids
used in this area continue in their development.

Equipment Designs
Application success is dependent on the fluid technology combined with proper application
method. The equipment must be rugged, yet user and maintenance friendly. The following is a list of
components required for a complete spray application system, along with some suggestions for
success:

3-29
Tooling - Chapter 3

Component Important Details

Fluid Reservoir Use stainless steel or coated metals to provide
flexibility in fluid compatibility.
Automate filling and mixing.
Test for correct fluid dilutions.
Clean out on scheduled basis.
Spray Metering, Atomization and Pattern Definition Protect fluid metering from high heat areas.
Shape the spray according to the tool to be
coated.
System Actuation, Control and Supply Lines Include flow controls and gages for adjustment
and monitoring.
Filter liquid to no less than 80-mesh particle
size.
Spray Mounting Assemblies Protect spray devices from press and billet
movement.
Observe press cycle and operation prior to
installation.
Provide flexibility for ease of operation and
maintenance.

Proper installation, combined with complete operator training, is then the most important
factor in the potential ongoing success of press tool spray lubrication systems.
Results with Automatic Spray Coating of
Press Tools
Today, a variety of pre-designed and
pre-assembled packages are available for a
variety of applications; the three most common
applications are butt shear blades, log shearing
knives, and dummy blocks. Butt and log shear
systems can be economical, simple to install
and maintain, and easily cost justified in most
applications. Dummy block spray systems, on
the other hand, are more complex and
expensive in nature due to the requirement for
limiting their effect on dead cycle time. Specific
applications will now be discussed.
Butt Shear Lubrication - Spray lubrication of the Figure 3-21: Remote mounting of nozzles away
butt shear blade can virtually eliminate sticking from the heat allows for easy adjustment and
butts, improve cut quality, lower shear repair.
pressures, and reduce cut deflection. Some
extruders lubricate only the die side, others coat the container side, and many hit both sides
according to user expectation, shear blade design, alloy pushed, discard butt lengths and extrusion
product mix. In all cases, spray is applied to both sides of the blade to insure even lubrication. One
extruder observed that the use of automatic lubrication on a blunt shear eliminated abnormal guide
and cylinder wear that previously caused complete press shut down twice yearly.
Log Shear Lubrication - Lubrication at the cutting tool interface and log contact points will instantly
reduce billet hang-up and build up in the shear, while also providing improved cut quality. With most
installations, the atomizing nozzles are mounted to the platen on the exit side of the shear and
remotely spray the upper sides of the tool where the fluid can then drain down to the lower cutting
edges. Spraying from the exit side allows for nozzle adjustment and repair out of the hot zone;
further, the atomized spray from the exit side is against the air flow out of the log oven (i.e. hot to
cold) which minimizes overspray (See Figure 3-21). A detailed investigation of one specific

3-30
 Tooling - Chapter 3

installation proved to virtually eliminate press downtime related to stuck logs when combined with
an improvement in shear tooling alignment; chips created in the cut and smearing of the log end were
also significantly reduced.
Dummy Block Lubrication Fixed dummy blocks have proven to be the most challenging tools to
spray lubricate automatically. The technology to date has required a spray nozzle to be moved in
front of the dummy block, spray the face and land, and move back out of the way of the press cycle.
In addition, due to the necessity for uniform dummy block wear, a rotating nozzle (rather than a fixed
nozzle) is used to apply the fluid. Ongoing developments (See Figure 3-22) continue to improve
system reliability, however the most successful
systems in operation still require ongoing
maintenance and operator intervention.
Many new presses and log shears built
today have automatic lubrication systems already
installed. This is a clear sign that there are
benefits to automatic lubrication of these vital
press functions.
Potential Pitfalls
Automatic spray lubrication, as with most
automation, has several inherent problems
associated with its use. The best designed
equipment and chemicals for this process must be
Figure 3-22: Rotating nozzles are driven
monitored and maintained properly so as to
with an air driven gearmotor for improved
provide optimal results.
system reliability.
With the fluids, it is important to see to
proper dilution and mixing of the concentrate with good quality water. In addition, the reservoir
must not be allowed to run dry, as this will put air into the fluid line, which causes inconsistent spray
patterns and volumes.
With the equipment, filters and seals must be changed and cleaned on a scheduled basis
prior to becoming deteriorated and causing a long list of other problems. Nozzle extensions must be
put back into position after being moved, in order to assure proper spray direction. Fluid volumes
and spray patterns may require some adjustment accordingly.
Improper system operation and maintenance can cause a variety of concerns that include,
but are not limited to, the following:
Overspray on equipment.
Clogging of nozzles.
Smoke and mist.
Investing the time, effort and training can make all the difference in assuring successful
implementation of spray equipment into the extrusion process. A successful installation will quickly
offer the benefits highlighted throughout this article.
Conclusion
Automatic lubrication of press tools is well documented to provide improvements in cut and
quality, while at the same time reducing or eliminating metal hang-up and sticking if performed on a
regular basis. The technology is at a point where the combination of application-specific chemicals,
used in combination with the proper applicator system, can be expected to operate continuously and
predictably to provide these results. As with all forms of automation, automatic spray lubrication
requires scheduled maintenance and adjustment so as to optimize expected results.
by James E. Dyla, President
AMCOL Corporation - 21435 Dequindre - Hazel Park MI 48030 - USA
Tel 248.414.5700 - Fax 248.414.7489
jim.dyla@amcolcorp.com - www.amcolcorp.com

3-31