21 300/112 ED

RQ*-P
PRESSURE RELIEF VALVES
SERIES 41

SUBPLATE MOUNTING
RQ3-P ISO 6264-06 (CETOP R06)
RQ5-P ISO 6264-08 (CETOP R08)

r
RQ7-P ISO 6264-10 (CETOP R10)

c.i
HYDRAULIC SYMBOL OPERATING PRINCIPLE
uli
ra

X P T
yd

Pilot operated pressure relief valve; main stage with

shutter and cone seal.
Subplate mounting in accordance with ISO 6264 (CETOP
RP 121H) standards.
Possibility of remote piloting using port X (see Hydraulic
Eh

symbol table).
The RQ*-P valves allow use of the entire flow of the
pump even with pressure values near the set value.
The wide passages allow reduced pressure drops,
improving the energy efficiency of the plant.

PERFORMANCES (measured with mineral oil of viscosity 36 cSt at 50C)

RQ3-P RQ5-P RQ7-P

Maximum operating pressure bar 350

Maximum flow rate l/min 200 400 500

Ambient temperature range C -20 / +50

Fluid temperature range C -20 / +80

Fluid viscosity range cSt 10 400

Fluid contamination degree According to ISO 4406:1999 class 20/18/15

Recommended viscosity cSt 25

Mass kg 3,5 4,3 6,5

21 300/112 ED 1/4
 RQ*-P
SERIES 41

1 - IDENTIFICATION CODE

R Q - P / / 41 /
Seals: omit for mineral oils
Double stage pressure relief valve
V = viton for special uids
Size: 3 = ISO 6264-06 (CETOP R06)
5 = ISO 6264-08 (CETOP R08) Series No.
7 = ISO 6264-10 (CETOP R10) (the overall and mounting dimensions
remain unchanged from 40 to 49)
Subplate mounting

Pressure adjustment range: M = adjustment with SICBLOC knob

3 = up to 70 bar 6 = up to 350 bar (omit for adjustment with hexagonal head screw)
5 = up to 210 bar

r
2 - CHARACTERISTIC CURVES (values obtained with viscosity of 36 cSt at 50C)
ADJUSTMENT MINIMUM CONTROLLED PRESSURE

c.i
uli
ra
3 - HYDRAULIC FLUIDS

Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals. For fluids HFDR type
(phosphate esters) use FPM seals (code V). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical
department. Using fluids at temperatures higher than 80 C causes a faster degradation of the fluid and of the seals characteristics.
yd

The fluid must be preserved in its physical and chemical characteristics.

4 - RQ3-P OVERALL AND MOUNTING DIMENSIONS

dimensions in mm
3
Eh

1 Mounting
surface with
103 sealing rings:
2 OR type 123
60 (17.86x2.62)
90 Shore
22
1 OR type 109
(9.13x2.62)
6 90 Shore
6 1 2 Hexagonal
head
53.8 adjustment
80 47.5
screw.
47.5 13 Spanner 13.
22.1
Clockwise
13 rotation to
2 increase
pressure.
26.9 X P T 80 X P T
53.8 3 Pressure
gauge port Y
14.7 (max) 3/8 BSP
G

4.8 7.5 M12 178.5

FASTENING BOLTS:
4 SHC bolts M12x40
MOUNTING SURFACE: ISO 6264-06-09-*-97 (CETOP 4.4.2-2-R06-350) Tightening torque: 69 Nm

21 300/112 ED 2/4
 RQ*-P
SERIES 41

5 - RQ5-P OVERALL AND MOUNTING DIMENSIONS

dimensions in mm

1 Mounting surface
3 with sealing rings:
N. 2 OR 3118
(29.82x2.62)
113
90 Shore
70 N. 1 OR 109
(9.13x2.62)
27 90 Shore
2 Hexagonal head
6 adjustment screw.
6
1 Spanner 13.
Clockwise rotation
66.7 to increase

r
55.6 pressure.
33.4 118 3 Pressure gauge

c.i
23.8 11.1 M16 35.8 port 3/8 BSP

15
2
35 P T
X
70 100 X P T
uli
G

6.3 23.4 (max) 7.5 170 FASTENING BOLTS:

ra
4 SHC bolts M16x50
Tightening torque 170 Nm
MOUNTING SURFACE: ISO 6264-08-13-*-97 (CETOP 4.4.2-2-R08-350)

6 - RQ7-P OVERALL AND MOUNTING DIMENSIONS

yd

dimensions in mm

123
Eh

1 Mounting surface
80 with sealing rings:
35 N. 2 OR 4137
(34.52x3.53)
90 Shore
6 N. 1 OR 109
6
1 (9.13x2.62)
90 Shore
2 Hexagonal head
88.9 adjustment screw.
76.2 Spanner 13.
152 Clockwise rotation
44.5
44.1 to increase
31.8 12.7 pressure.
3 Pressure gauge
18.7 port 3/8 BSP
41.3 P T
X 32 (max)
82.6 120 X P T
2
G
FASTENING BOLTS:
4 SHC bolts M18x60
6.3 7.5 M18 180 Tightening torque: 235 Nm
MOUNTING SURFACE: ISO 6264-10-17-*-97 (CETOP 4.4.2-2-R10-350)

21 300/112 ED 3/4
 RQ*-P
SERIES 41

7 - ADJUSTMENT KNOB

The RQ valves can be equipped with a SICBLOC adjustment knob. To operate it, push and rotate at the
same time.
To request this option, add: /M (see paragraph 1).

8 - SUBPLATES (see catalogue 51 000)

RQ3-P RQ5-P RQ7-P

PMRQ3-AI4G PMRQ5-AI5G PMRQ7-AI7G
Type
rear ports rear ports rear ports
P: 1/2 BSP
P, T ports dimension 1 BSP 1 1/4 BSP

r
T: 3/4 BSP

c.i
X port dimension 1/4 BSP 1/4 BSP 1/4 BSP

uli
ra
yd
Eh

DUPLOMATIC OLEODINAMICA S.p.A.

20015 PARABIAGO (MI) Via M. Re Depaolini 24
Tel. +39 0331.895.111
Fax +39 0331.895.339
www.duplomatic.com e-mail: sales.exp@duplomatic.com

21 300/112 ED REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.
4/4