Datcom K3

Communication module
TYPE
DATCOM-K3
accessories for the correctors and data logger

isolating barrier for communication device connection
isolating barrier for digital output form connected device
communication interface conversion RS232/ RS485
possibility of modem connection
external power supply for one corrector or data logger
variation with decreased consumption
1
Technical description
DATCOM-K3 is designed as accessories for the correctors miniELCOR, maxiELCOR,
midiELCOR, ELCOR-2, microELCOR-2 and electronic data logger miniDATCOM, maxiDATCOM, midi-
DATCOM and DATCOM-2. The device is designed as associated apparatus from the point of intrinsic
safety and the device has to be installed outside of hazardous area during operation. Safety standards
and safety parameters of intrinsic safety have to be respected with regards to using the device with other
devices (see chapter Technical data).
Communication module DATCOM-K3 is power supplied with direct tension 12 V.
Communication module DATCOM-K3 is manufactured into plastic box and is assembled on DIN
bar 35 mm into distributor. Clamps with maximum cross-section 1,5 mm2 are determined for connection of
the cables.
Communication module provides following functions:

communication with either one or more devices (e.g. correctors) connected with intrinsically
safe (JB) communication interface RS-485 (port P0)
safe separation of communication interface RS-485 (port P0) and conversion to communication
interface RS-232 (port P2)
safe separation (isolating barrier) for intrinsically safe digital outputs of the device
external power supply for connected device
Main function of this communication module is to provide interface between intrinsically

safe circuits (the device installed in hazardous area) and other circuits (the device installed outside of
hazardous area). Module realises function of intrinsically safe separator partly for communication circuit of
corrector or datalogger and also for their output circuits. Other device (such as PC, modem, etc.) may be
connected to the non-intrinsically safe circuit of DATCOM-K3 and also consecutive system for processing
of output pulses from correctors.
Data transmission between port P0 and P2 is transparent, communication speed and
communication protocol are not changed. Likewise, signals transfer from DI1 - DI4 to clamps DO1 DO4
are transparent.
Module DATCOM-K3 contains also intrinsically safe power supply which may be with
some limitation (see further) used for power supply of one corrector or datalogger.
Communication module DATCOM-K3 is prepared for upgrade of processor board
(upgrade to module DATCOM-K4 respectively DATCOM-K4/A).
Module is manufactured in two variants, in basic variant DATCOM-K3 and in variant DATCOM-
K3/A to be powered using the accumulator only.
2
Technical data
Mechanical parameters
plastic box for assembly on DIN bar
dimensions (width x height x length) 93 x 42 x 96 mm (height without holder)
weight 0,16 kg
clamps for connection of cables 1,5 mm2
ambient temperature -25 C to +60 C
storing temperature -40 C to +85 C
protection IP20 (according to EN 60529)
Non-hazardous variant
classification II (2)G [Ex ia] IIC
ATEX approval FTZ 05 ATEX 0364
classification of environment - hazardous area
- normal environment
(according to EN 33 2000-3)
galvanic separation (only for DATCOM-K3) 1 500 V
Power supply range (clamps 12V)
power supply range 12 VDC -10% / +25%
max. value of voltage Um 250 V (only for DATCOM-K3)
60 V (only for DATCOM-K3/A)
idle (own) current consumption *) typically 28 mA at 14 V (DATCOM-K3)
typically 2 mA (DATCOM-K3/A)
max. current consumption **) 120 mA (DATCOM-K3)
100 mA (DATCOM-K3/A)
max. length of cable 30 m
*) to the clamps, resp. connector is not connected to any outer circuit
**) to the connector, D-Sub is connected to the device (PC, modem) output clamps of intrinsically safe power supply
(6 V OUT) are short-circuited
Port P0 (intrinsically safe port)
communication interface RS-485
communication speed 4 800 Bd to 38 400 Bd
max. length of cable 100 m 1)
Port P2
communication speed 4800 Bd to 38 400 Bd
- communication interface RS232 (connector D-Sub9)
- communication interface RS485 (terminals D-, D+)
max. length of cable 1 200 m
number of line wire 2
Digital inputs DI1 to DI4 (intrinsically safe)
number of inputs 4
Digital outputs DO1 to DO4
number of outputs 4
type of output open collectro
max. voltage 30 V
max. current 100 Ma
max. resistance at fastened state 10 R
Intrinsically safe power supply (clamps 6V OUT)
off-load voltage typically 6,2 V
current limitation typically 74 mA
1)
Inductivity and capacity of cable (depends on used length and type of cable) has to be in accordance
with parameters of system non explosiveness.
3
Basic variant DATCOM-K3
Basic variant is determined for systems which are powered from network voltage (Um = 250V).
DATCOM-K3 may be powered from not back-up mains source or from the source which is back-up with
accumulator, charged with mains charger, etc.
Fig. 1 Basic variant DATCOM-K3, principle of use

This manufacturing variant has galvanic separation between intrinsically safety circuits (blue
clamps) and other circuits (orange clamps).
Variant DATCOM-K3/A
Manufacturing variant DATCOM-K3/A has got decreased consumption with comparison to basic
variant. Using of DATCOM-K3/A is determined for systems which are powered from accumulator only.
Accumulator may also be charged with solar panel (Um = 60V).
Fig. 2 Variant DATCOM-K3/A, principle of use
This manufacturing variant does not have galvanic separation between intrinsically safe input cir-
cuit (blue clamps) and other circuit (orange clamps). All GND clamps are interconnected mutually.
Manufacturer: ELGAS, s.r.o., Ohrazenice 211, 533 53 Pardubice, Czech Republic

Tel.: +420/ 466 414 500, 466 414 511 fax: +420/ 466 411 190
E-mail: sales@elgas.cz, http://www.elgas.cz
The company is a holder of certified quality system ISO 9001 with international validity
and it is authorised to manufacture equipment for hazardous areas.
L060EN_201201 4

Datcom K3

Uploaded by

Copyright:

Available Formats

Datcom K3

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Datcom K3

Uploaded by

Copyright:

Available Formats

Communication module

accessories for the correctors and data logger

Communication module provides following functions:

Main function of this communication module is to provide interface between intrinsically

Fig. 1 Basic variant DATCOM-K3, principle of use

Fig. 2 Variant DATCOM-K3/A, principle of use

Manufacturer: ELGAS, s.r.o., Ohrazenice 211, 533 53 Pardubice, Czech Republic

You might also like