FMC Mining Machinery 2015

FMC- Mining Machinary
Question Text:
For no slip condition the limiting ratio of the tension of the two sides of a belt conveyor is
Options:
(1) T1/T2 < e
(2) T1/T2 = e
(3) T1/T2 > e
(4) T1/T2 e
(5) None of the Options
Correction Answer : Option No.(2)

Question Text:
Minimum number of dead turns of the rope on drum in winder
Options:
(1) 1 turn
(2) 1-2 turns
(3) 2-3 turns
(4) 3-4 turns
(5) 5 turns

Question Text:
Automatic contrivances provided with drum winder is mandatory for the shaft depth of
Options:
(1) <60m
(2) 60-90m
(3) 100m
(4) 150m
(5) 200m

Question Text:
Recapping of haulage rope should be performed once at least in every
Options:
(1) 3 months
(2) 6 months
(3) 9 months
(4) 1 year
(5) 1 years

Question Text:
The fluid used in the SDL and LHD machines is
Options:
(1) HFA
(2) HFB
(3) HFC
(4) HFD
(5) Mineral Oil

Question Text:
The ratchet and pinion mechanism is used
Options:
(1) To restrict the rotation in one direction.
(2) To restrict the rotation in both direction.
(3) To allow the rotation in both direction.
(4) To lift load.

Question Text:
The loop take up system of belt conveyor is provided for
Options:
(1) For tensioning the belt when required
(2) To accommodate extra belt
(3) To avoid regular shortening of the belt
(4) Used in longer- lengths of conveyors
(5) All the Options

Question Text:
Compressed air driven machines are generally designed for the operating pressure
Options:
(1) <3 bar
(2) 3-5 bar
(3) 6-7 bar
(4) 8-10 bar
(5) > 10 bar

Question Text:
One of these is not a safety device in the belt conveyor system
Options:
(1) Pull cord system
(2) Lock out system
(3) Painter plate
(4) Pre-start warning system
(5) Warning through Telephone

Question Text:
The fibre core of a wire rope is thoroughly impregnated with a lubricant for all but one of the
following reasons
Options:
(1) To prevent absorption of moisture
(2) To inhibit corrosion inside the rope
(3) To give additional strength to the rope
(4) To preserve the shape of the rope under strain

Question Text:
Which of the following advantages of Koepe Winder is FALSE
Options:
(1) Requires only half the space needed for the Drum Winder
(2) Most suitable for winding bigger loads from greater depths
(3) Suitable for winding from more than one level
(4) Arrangement is simple,compact and lighter
(5) No extra coils of main rope is required.

Question Text:
AFC in longwall mining stands for
Options:
(1) Armed face conveyor
(2) Armoured face conveyor
(3) Armed flexible conveyor
(4) Armoured flexible chain

Question Text:
For a given set of geo-mining conditions, the longwall package is decided upon
Options:
(1) The capacity of the powered supports
(2) The capacity of the shearer machine
(3) The capacity of the AFC
(4) The capacity of the power pack
(5) The capacity of the gate belt conveyor

Question Text:
Which of the following do not have identical dimensions
Options:
(1) Momemtum and impulse
(2) Torque and energy
(3) Torque and work
(4) Moment of a force and angular momentum

Question Text:
Forging means
Options:
(1) Heating and striking
(2) Heating
(3) Melting
(4) Hammering
(5) Turning

Question Text:
Head and tail stocks are the main components of
Options:
(1) Lathe machine
(2) Milling machine
(3) Shaper machine
(4) Drilling machine
(5) Planer machine

Question Text:
Prime mover of electric dumper
Options:
(1) Diesel engine
(2) Electric motor
(3) Hydraulic motor
(4) Pneumatic motor
(5) All the Options

Question Text:
Gate end box is basically a
Options:
(1) Transformer
(2) Junction Box
(3) Switch gear with protective devices
(4) Transformer and Junction Box
(5) All the Options

Question Text:
Which of these is not a safety feature in the continuous miner
Options:
(1) Water interlock
(2) Dust scrubber
(3) Methane monitor
(4) Gathering arm
(5) Emergency stop switch

Question Text:
The blade of multi-stage axial flow fan is of
Options:
(1) Aerofoil Cross-section
(2) Trapezoidal Cross-section
(3) Rectangular Cross-section
(4) Square Cross-section

Question Text:
__________ is mounted on the boiler and its function is to put off the fire in the furnace when
water level falls below the safe limit
Options:
(1) stop valve
(2) safety valve
(3) fusible plug
(4) blow off cock

Question Text:
Which of the these is not a circuit breaker
Options:
(1) OCB
(2) VCB
(3) SF6
(4) ACB

Question Text:
Speed control of induction motor can be effected by varying
Options:
(1) Flux
(2) Voltage input to stator
(3) Keeping rotor coil open
(4) All the options

Question Text:
The transfomer laminations are insulated from each other by
Options:
(1) Mica strip
(2) Thin coat of varnish
(3) Paper
(4) All the options

Question Text:
CBT used in gateend box is to sense
Options:
(1) Over load current
(2) Single phasing
(3) Unbalanced supply system
(4) Earth fault current
(5) All the Options

Question Text:
Flexible trailing cable used with
Options:
(1) Shearer motor
(2) Rope haulage motor
(3) Mine winder motor
(4) Pump motor
(5) All the Options

Question Text:
Flameproof enclosure is necessary for
Options:
(1) Intrinsically safe circuit
(2) Coal face motor
(3) Gate end box
(4) Coal face motor and Gate end box
(5) All the Options

Question Text:
Haulage signalling cirucit is
Options:
(1) Intrinsically safe circuit
(2) High voltage circuit
(3) Low voltage circuit
(4) Capacitive circuit
(5) inductive circuit

Question Text:
Static Ward-Leonard Device is used to control the speed of
Options:
(1) DC motor
(2) Induction motor
(3) Synchronous motor
(4) Shunt motor
(5) Compound motor

Question Text:
Drill cable is a
Options:
(1) 5 core flexible trailing cable
(2) Five core pliable wire armoured trailing cable
(3) Three core PVC cable
(4) 3.5 core XLPE cable
(5) All the Options

Question Text:
Retarder is put into operation when dumper is moving in
Options:
(1) uphill road
(2) down hill road
(3) undulated road
(4) level road
(5) All the Options

Question Text:
The function(s) of turbo-charger in engines is
Options:
(1) supply engine cylinder with compressed air
(2) increase the power output
(3) supply engine cylinder with compressed air and increase the power output
(5) increase speed

Question Text:
Nitrogen gas under pressure is filled in dragline boom for
Options:
(1) increasing the strength of the boom
(2) detecting crack in the boom
(3) resisting corrosion
(4) making environment eco-fiendly
(5) All the Options

Question Text:
PVC belt possesses
Options:
(1) fire resistance property
(2) anti slippage property
(3) high co-efficient friction value than rubber belt
(5) high capacity of transportation

Question Text:
Melting point of white metal used for re-capping of mine winder ropes is
Options:
(1) 150C
(2) 270C
(3) 365C
(4) 600C
(5) 400C

Question Text:
Centrifugal fan develops
Options:
(1) equall pressure as developed by axial flow fans
(2) less pressure than developed by axial flow fans
(3) higher pressure than developed by axial flow fans
(4) only flow
(5) only pressure

Question Text:
Jack hammer drills are
Options:
(1) rotary type drill machine
(2) rotary percussive type drill machine
(3) percussive type drill machine
(4) DTH type drill machine
Question Text:
Gate end box is basically a
Options:
(1) star-delta starter
(2) A DOL Starter
(3) A step up transformer
(4) A step down transformer
(5) Auto transformer starter

Question Text:
Function of cowl and dozer plate in shearer is
Options:
(1) to protect the cutting drum from loose coal failing from roof
(2) to protect the cutting drum from coal dust
(3) to increase the coal loading efficiency
(4) to increase the coal cutting efficiency
(5) All the Options

Question Text:
Why fleet angle is limited to 1.5
Options:
(1) To reduce the side travel on the pulley
(2) To prevent excessive wear and tear of the winding rope.
(3) To allow maximum persons to travel at a time.
(4) It allows use of rope having lesser diameter
(5) It allows minimum slippage.

Question Text:
One killowatt is equal to
Options:
(1) 1 HP
(2) 1.34 HP
(3) 1.40 HP
(4) 1.50 HP
(5) 1.74 HP

Question Text:
In torque converter
Options:
(1) Input torque > Output torque
(2) Output torque > Input torque
(3) Input torque= Outpur torque
(4) Input speed = Output speed
(5) Input speed < Output speed

Question Text:
Composition of white metal is
Options:
(1) Fe, Sn, Cu, Pb
(2) Au, Sn, Cu, Pb
(3) Au, Ag, Sb, Pb
(4) Sn, Sb, Cu, Pb

Question Text:
A typical composition of steel ropes percentage wise , used in mining , is
Options:
(1) C-0.5, S-0.003, P-0.014, Fe-Rest
(2) C-2.0, S-0.003, P-0.014, Fe-Rest
(3) C-2.0, S-3.0, P-0.014, Fe-Rest
(4) C-0.5, S-3.0, P-0.014, Fe-Rest

Question Text:
A steam winder of 25 HP is used for both man and material winding as well as coal winning .The
driver of the winder should possesses
Options:
(1) I Class Engine Driver's Certificate
(2) II Class Engine Driver's Certificate
(3) Manager's Permit
(4) Manager's authorisation

Question Text:
Setting pressure of a powered support should be _____% of yield pressure of the powered support
Options:
(1) 50
(2) 50-60
(3) 65-75
(4) 75-85
(5) More than 85

Question Text:
Hydraulic pressure is required at the gate belt conveyor for
Options:
(1) Tensioning the belt
(2) Shortening the belt
(3) Shifting the gate belt tailend function
(4) Providing sprinkling arrangement on the gate belt
(5) All the Options

Question Text:
Buttress supports in a longwall face
Options:
(1) Face end supports at the gate roads
(2) Mid face supports
(3) Supports over the stage loader
(4) supports at the 35% and 65% portion of a longwall face where load is maximum

Question Text:
Time dependent yield is known as
Options:
(1) Fracture
(2) Fatigue
(3) Buckling
(4) Creep
(5) None

Question Text:
Blair winder is basically a
Options:
(1) Multi-rope double drum winder
(2) Single rope friction winder
(3) Multi-rope friction winder
(4) Single rope drum winder
(5) Drum with center weight

Question Text:
A vane pump and gear pump are a type of
Options:
(1) Non-positive displacement pump
(2) positive displacement pump
(3) either positive displacement or non-positive displacement pump
(4) reciprocating pump
(5) All the Options

Question Text:
In isentropic process of compression, the change in entropy is
Options:
(1) more than zero
(2) less than zero
(3) equals to zero
(4) All the options

Question Text:
The methane sensor incorporated in the continuous miner cuts off the power to the machine,
when the methane percentage reaches.
Options:
(1) 0.75
(2) 1
(3) 1.25
(4) 1.5
(5) >2.00

Question Text:
Compression ratio of diesel engine has a range of
Options:
(1) 8 to 10
(2) 10 to 15
(3) 16 to 20
(4) 21 to 25

Question Text:
The neutral point is the position of the booster at which
Options:
(1) The pressure difference between the intake and return is equal the booster fan pressure
(2) The pressure difference between the intake and return is less than the booster fan pressure
(3) The pressure difference between the intake and return is higher than the booster fan pressure
(4) All the options

Question Text:
The accurate sizing and finishing operation performed on a previously drilled hole is called as
Options:
(1) Drilling
(2) Boring
(3) Shaping
(4) Reaming
(5) Sinking

Question Text:
The full load copper loss of a transformer is 1600 W. At half-load the copper loss will be
Options:
(1) 6400W
(2) 1600W
(3) 800W
(4) 400W

Question Text:
Power transformers are generally designed to have maximum efficiency around
Options:
(1) No load
(2) Half load
(3) Near full load
(4) 10% overload

Question Text:
The power factor in an AC circuit is defined as
Options:
(1) The actual power divided by the maximum power the circuit can handle
(2) The ratio of the real power to the imaginary power
(3) The ratio of the apparent power to the true power
(4) The ratio of the true power to the apparent power
(5) The ratio of the imaginary power to the apparent power

Question Text:
A transformer has negative voltage regulation when its load power factor is
Options:
(1) Zero
(2) Unity
(3) Leading
(4) Lagging
Question Text:
The DC motor, which can provide zero speed regulation at full load without any controller is
Options:
(1) Series
(2) Shunt
(3) Cumulative compound
(4) differential compound

Question Text:
Three phase double cage induction motor for shearer machine demands
Options:
(1) High starting torque
(2) constant speed
(3) Low starting voltage
(4) Low starting torque
(5) Low starting power

Question Text:
Full load slip of induction motor should be
Options:
(1) Low
(2) High
(3) Zero
(4) one

Question Text:
Transformer neutral for three phase power supply of shovel is grounded to a resistor to avoid
Options:
(1) Shock hazard
(2) Explosion hazard
(3) High earth fault current
(4) High voltage hazards
(5) Shock hazard and High earth fault current

Question Text:
6 x 21 stranded rope of same diameter is
Options:
(1) more rigid compared to 6 x 9 stranded rope
(2) more flexible compared to 6 x 9 stranded rope
(3) equally rigid and equally flexible like 6 x 9 stranded rope
(4) more rigid and less flexible compared to 6 x 9 stranded rope
(5) All the Options

Question Text:
Lilly controller in drum winder is required
Options:
(1) To immediately apply the brake when a man tries to enter into the cage before stopping
(2) To stop the hoist immediately when normal speed is exceeded.
(3) To check whether the skip is properly filled before hoisting
(4) To prevent over speeding in lowering and raising a skip
(5) To prevent over loads of the winder.

Question Text:
The profile of the gear teeth
Options:
(1) Cycloidal
(2) Helical
(3) Involute
(4) Cycloidal and Involute
(5) Helical and Involute

Question Text:
The maximum diameter of the hole that can be punched from a plate of maximum shear stress
1/4 th of its maximum crushing stress of punch, is equal to (where t = Thickness of the plate)
Options:
(1) t
(2) 2t
(3) 4t
(4) 8t
(5) 3t

Question Text:
When trying to turn a key into a lock, following is applied
Options:
(1) Couple
(2) Non-coplanar forces
(3) Moment
(4) Coplanar force
(5) Non-complaner force

Question Text:
In a hydrodynamic journal bearing, there is
Options:
(1) a very thin film of lubricant between the journal and the bearing such that there is contact
between the journal and the bearing
(2) a thick film of lubricant between the journal and the bearing
(3) no lubricant between the journal and the bearing
(4) a forced lubricant between the journal and the bearing

Question Text:
The usual stroke frequency of jack hammer drill is
Options:
(1) 500 strokes/min
(2) 1000 strokes/min

Question Text:
The basic difference in the fan, compressor and blower is
Options:
(1) in their operating speed
(2) compression ratio of air
(3) rate of air delivered
(4) power of the machine

Question Text:
1 mm water gauge is equivalent to
Options:
(1) 10 Pa
(2) 1.0 Pa
(3) 100 Pa
(4) 0.10 Pa
(5) 5 Pa

Question Text:
Dozer blade has the dimension of 4500 mm x 2000 mm operates on level ground. The output
capacity of the dozer is
Options:
(1) 11 m3 approx)
(2) 15 m3 (approx)
(3) 20 m3 (approx)
(4) 8 m3 (approx)
(5) 10 m3 (approx)

Question Text:
The maximum static tension on a rope when the weight of the cage with its suspension gear etc. Is
6 tonnes, hoisting depth is 300 m and rope weight is 40 N/m
Options:
(1) 70 kN
(2) 72 kN
(3) 75 kN
(4) 80 kN
(5) 100 kN

Question Text:
A refrigerator operates between 255 K and 303 K has the maximum possible coefficient of
performance
Options:
(1) 21.32
(2) 2.35
(3) 1.8
(4) 2.1
(5) 2.5

Question Text:
Power factor of synchronous motor
Options:
(1) can be controlled
(2) can not be controlled
(3) may vary between lagging and leading power factor
(4) can be controlled and may vary between lagging and leading power factor
(5) All the Options

Question Text:
An AFC of length 114 m run at a speed of 0.535 m/sec. The mass of chains and flights is 54 kg.m,
and the coefficient of friction between the chain and through is 0.33. The power needed to run the
empty conveyor is
Options:
(1) 6.94 kW
(2) 10.68 kW
(3) 21.36 kW
(4) 25.74 kW
(5) 15 kW

Question Text:
A conveyor is 600 m long and carried coal of bulk density 0.8 t/ m 3 up a gradient of 1 in 60 at the
rate of 220 t/hr.
If the belt width (w) is 0.75 m and cross sectional area of the materials is 0.1 w 2
determine the belt speed
Options:
(1) 0.04 m/sec
(2) 0.96 m/sec
(3) 1.36 m/sec
(4) 1.80 m/sec
(5) 1.5 m/sec

Question Text:
The percentage of Manganese is in the steel used for the bucket teeth of an excavator
Options:
(1) 1% - 1.5%
(2) > 1%
(3) 1.5% - 5%
(4) 5% - 8%
(5) 11% - 14%

FMC Mining Machinery 2015

Uploaded by

Copyright:

Available Formats

FMC Mining Machinery 2015

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FMC Mining Machinery 2015

Uploaded by

Copyright:

Available Formats

FMC- Mining Machinary

Correction Answer : Option No.(2)

Correction Answer : Option No.(3)

Correction Answer : Option No.(3)

Correction Answer : Option No.(2)

Correction Answer : Option No.(2)

Correction Answer : Option No.(1)

Correction Answer : Option No.(5)

Correction Answer : Option No.(3)

Correction Answer : Option No.(3)

Correction Answer : Option No.(3)

Correction Answer : Option No.(1)

Correction Answer : Option No.(2)

Correction Answer : Option No.(1)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(1)

Correction Answer : Option No.(1)

Correction Answer : Option No.(3)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(3)

Correction Answer : Option No.(5)

Correction Answer : Option No.(2)

Correction Answer : Option No.(2)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(1)

Correction Answer : Option No.(1)

Correction Answer : Option No.(2)

Correction Answer : Option No.(3)

Correction Answer : Option No.(2)

Correction Answer : Option No.(1)

Correction Answer : Option No.(3)

Correction Answer : Option No.(3)

Correction Answer : Option No.(2)

Correction Answer : Option No.(3)

Correction Answer : Option No.(2)

Correction Answer : Option No.(2)

Correction Answer : Option No.(2)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(2)

Correction Answer : Option No.(4)

Correction Answer : Option No.(3)

Correction Answer : Option No.(1)

Correction Answer : Option No.(4)

Correction Answer : Option No.(1)

Correction Answer : Option No.(2)

Correction Answer : Option No.(3)

Correction Answer : Option No.(1)

Correction Answer : Option No.(3)

Correction Answer : Option No.(1)

Correction Answer : Option No.(4)

Correction Answer : Option No.(4)

Correction Answer : Option No.(3)

Correction Answer : Option No.(4)