Medium Voltage Distribution

SF circuit breakers
up to 40.5 kV
fixed and withdrawable versions

Catalogue

2008
 SF circuit breakers

One range of comprehensive and proven SF1 circuit breakers fixed version from 12 kV to 36 kV
three-pole circuit breaker units for indoor
installation using SF6 technology.
Both compact and dependable, it is ideally
suited to the most demanding applications.
This circuit breaker range meets

PE56503
IEC standard 62271-100.

SF2 circuit breakers fixed version from 24 kV to 40.5 kV

PE56501

SF F400 circuit breakers withdrawable version

from 24 kV to 40.5 kV
PE56502
General contents

General presentation 2

Panorama 4

SF1 and SFset circuit breakers

fixed version 7

SF2 circuit breakers

fixed version 25

SF F400 circuit breakers

withdrawable version 35

1
 General presentation SF circuit breakers
The advantages of proven technology

With over 37 years industrial experience in Safety

SF6 techniques and over 300,000 installed The breaking medium is sulfur hexafluoride (SF6) used at low pressure.
The insulating enclosure containing the circuit breaker pole(s) is equipped with
devices throughout the world, a safety membrane.
Schneider Electric is today one of the In addition, the rated characteristics, breaking the rated current under the rated
foremost manufacturers of SF6 switchgear. voltage, are generally maintained at zero relative bars of SF6.
Schneider Electric has developed a wide
range of high performance and reliable Reliability
devices operating faultlessly on all The motor-charged spring stored energy operating mechanism is a key factor
5 continents. of device reliability: Schneider Electric cumulates 37 years experience with
Continuously increasing its performance, this type of mechanism, 300,000 of which are already in operation.
Schneider Electrics mastery of design and the testing of sealed systems guarantees
the company maintains a very high level sustained device performance for at least 30 years.
of innovation in its offer.
Increased endurance
The mechanical and electrical endurance of Schneider Electric SF6 breaking
61051N

devices are in conformity with the most demanding specifications recommended by

the IEC.
These devices therefore meet requirements for even the most exposed of networks.

Less maintenance
Throughout the devices service life, which in normal operating conditions may be
at least 30 years, the only maintenance required is on the mechanical operating
mechanism, once every 10 years or every 10,000 operations.
Although no maintenance is performed on poles, a diagnosis is possible:
b contact wear can be checked by external pole measurement
b SF6 pressure can be continually monitored by a pressure switch.

Environmentally-friendly
Schneider Electric devices have been designed to ensure protection of
the environment:
b the materials used, both insulating and conductive, are identified and easy
to separate and recycle
b the SF6 gas is under control from production through to the circuit breakers end
of life. In particular it can be recovered at the end of the circuit breakers life and
re-used after treatment in line with the new European directive
b an end of life manual for the product details procedures for dismantling and
recycling components.

Quality Assurance
During production, each circuit breaker undergoes systematic routine tests
in order to check quality and conformity:
b pole sealing check
b checking the correct mechanical operation of the device,
b plus its associated locking mechanisms
b checking simultaneous closing of contacts
b checking power frequency insulation level
b checking main circuit resistance
b checking auxiliary circuit insulation
b checking auxiliary circuit electrical resistance
b checking switching speeds
b checking the switching cycle
b measuring the switching times.
The results are recorded on the test certificate for each device
which is initialed by the quality control department.
DE55745

DE55746

Certification
The quality system for the design and production of SF range circuit breakers is
certified in conformity with ISO 9001: 2000 quality assurance standard requirements.
The environmental management system adopted by Schneider Electric production
sites for the production of SF range circuit breakers has been assessed and judged
to be in conformity with requirements in standard ISO 14001.

2
General presentation SF circuit breakers
Breaking principle

Breaking principle: puffer type

SF circuit breakers use the puffer principle with SF6 gas.
This methods cools and extinguishes the electrical arc as it passes through zero
current by puffing a gas compressed by a piston attached to the moving contact.
The gas is channeled by an insulating nozzle towards the tubular arcing contacts
that are used as an exhaust.
This breaking technique is used for high-performance breaking applications
(40.5 kV-31.5 kA) and has been used for the past 37 years.
The operating sequence in a puffer-type breaking chamber with the moving part
actuated by a control mechanism is as follows:

b the circuit breaker is closed

DE51238

b following an opening order the main contacts

DE57439

separate (a) and the current is directed into the

breaking circuit (b). When the main contacts start
to open the piston (c) slightly compresses the SF6 gas
a in the compression chamber (d)

c
b
d

b an electrical arc appears on separation of the arcing

DE57440

contacts. The piston (c) continues its travel downwards.

A small quantity of the gas channeled by the insulating
nozzle (e) is injected towards the arc. For low current
breaking, the arc is cooled by forced ventilation.
However, for high currents the thermal expansion
e moves the hot gases towards cooler parts
c in the breaking unit.
The distance between arcing contacts becomes
sufficient to allow breaking of the current when it
passes through zero due to the dielectric properties
of the SF6 gas

b the moving parts finish their movement and injection

DE51241

of cold gas continues until the contacts are fully open.

The circuit breaker is open.

3
Panorama SF circuit breakers

Circuit breakers

SF range circuit breakers

SF1 fixed SFset fixed SF2 fixed

Side or front operating mechanism Side or front operating mechanism Front operating mechanism
with integrated VIP
Rated voltage Ur (kV, 50/60 Hz)

Rated short-circuit breaking current (Isc)

25 kA from 12.5 to 25 kA 25 kA from 12.5 to 25 kA from 12.5 from 25 31.5 kA
to 40 kA to 40 kA
Rated current (Ir)
630 A from 400 to 1250 A 630 A from 400 to 1250 A from 630 to 3150 A 2500 A

4
Panorama SF circuit breakers (cont.)

Protection, monitoring and control

SFset circuit breakers SF1/SF2/SF F400 C. B.

MERLIN GERIN ext 0 off I on Trip

1 > 51 1 > >51 1o > 51 1o > >51
Sepam on

I1 = 165A RMS
I2 = 166A RMS
I3 = 167A RMS

SF F400 withdrawable VIP300P Sepam series 20

Front operating mechanism for phase protection for normal applications

VIP300LL Sepam series 40

for phase and for demanding applications
earthing protection
Sepam series 80
for customized applications

Separate catalogue

40 kA from 25 to 40 kA 31.5 kA

3150 A 1250 and 2500 A 1250 A

5
6
SF circuit breakers SF1 and SFset circuit breakers
fixed version

General presentation 2
Panorama 4
Presentation 9
General characteristics 10
Description of functions 12
RI stored energy operating mechanism 12
Wiring diagram 12
Opening circuit 13
Remote control 14
Indication and locking/interlocking 15
Protection, monitoring and control 16
VIP300 protection unit 16
Trip curves for VIP300P and VIP300LL 17
Current sensors and test unit for VIP300 18
Dimensions 19
Order form 22
SF2 circuit breakers fixed version 25
SF F400 circuit breakers withdrawable version 35

7
8
 SF1 and SFset Presentation
circuit breakers
fixed version

Description of the device

The basic withdrawable version of the SF circuit breaker comprises:
b 3 main independent poles, that are mechanically linked and each comprising
a sealed pressure system type insulating enclosure. The sealed enclosure is filled
PE56505

with low pressure SF6 gas

b a stored energy operating mechanism of manual RI type (that can be electrically
operated as an option)
This gives the device an opening and closing speed that is independent
of the operator, for both electrical and manual orders.
When equipped with an electrical operating mechanism, the circuit breaker can be
remotely controlled and it is possible to carry out reclosing cycles.
b a front panel housing the manual operating mechanism and status indicators
b upstream and downstream terminals for the power circuit connection
b a terminal block for connection of external auxiliary circuits.
According to its characteristics, the SF circuit breaker is available either in frontal
version or in lateral version.
SF1 circuit breakers with a B1 side operating mechanism Each device can be optionally equipped with:
b an electrical operating mechanism
b a support frame fitted with rollers and floor securing brackets for a fixed installation
b locking of the circuit breaker in the open position by a keylock installed on the
control panel
b a pressure switch for the high performance versions
b a Harting 42-pin type LV connector.
PE56504

The SFset includes an independent protection chain

The SFset is provided with a fully autonomous integrated protection chain
(with a VIP type control unit) operating without an auxiliary power source.
The VIP protection unit exists in two models: VIP300P and VIP300LL.
DE57400

kA
25

20 VIP300LL

16

12,5 VIP300P - VIP300LL

0 17,5 24 kV
SFset circuit breakers with a B1 side operating mechanism
Depending on the model, the unit provides protection against phase over-currents
and earthing faults.
VIP protection units are associated with functional current sensors.
Two interchangeable sensors, CSa and CSb, are sufficient to cover all requirements
from 10 to 1250 A.
SFset is delivered equipped and cabled with its protection chain, this simplifies panel
builders installation work.
DE57401

SF1

Mitop

CS VIP

SFset schematic diagram

Applications
SF circuit breakers are 3-pole MV circuit breakers for indoor installation.
They are mainly used for switching and protection of networks from 12 to 36 kV
in primary and secondary power distribution.
Because the SFset protection chain is autonomous in terms of power, this circuit
breaker is particularly suited to certain dispersed installations on the network.
The autocompression breaking technique used in these circuit breakers means that
making or breaking all types of compacitive or inductive currents can be achieved
without dangerous overvoltages for the switchgear connected to the network.
The SF circuit breaker is therefore well suited to operating capacitor banks.

9
SF1 and SFset General characteristics
circuit breakers
fixed version

Electrical characteristics according to IEC 62271-100

SF1

PE56503
Rated voltage Ur kV 50/60 Hz 12 17.5
Insulation voltage
- power frequency withstand Ud kV 50 Hz 1min 28 38
- lightning impulse withstand Up kV peak 75 95
Rated current Ir A 400 b
630 b b b b
1250 b b b
Short circuit current Isc kA 25 12.5 20 25
Short time withstand current Ik/tk kA/3 s 25 12.5 20 25
Short-circuit making current Ip kA peak 50 Hz 62.5 31.3 50 62.5
60 Hz 65 32.5 52 65
Rated switching sequence O-3 min-CO-3 min-CO b b
O-0.3 s-CO-3 min-CO b b
O-0.3 s-CO-15 s-CO b b
Phase to phase mm 220 b b b
250 b b b b
280
350
380
Operating mechanism A1 lateral (*) b b b
B1 lateral (*) b b b
C1 frontal (*) b b b
For SM6 switchgear b b
Operating times Opening (ms) < 50
Breaking (ms) < 60
Closing (ms) < 65
Service temperature T C 25 to +40
Mechanical endurance Class M2
Number of switching operations 10,000
Electrical endurance Class E2
Capacitive current breaking capacity Class C2

b Available
Not available
(*) See chapter Dimensions.

Specific applications
Switching and protection of capacitor banks
SF range circuit breakers are particularly well suited to switching and protection
of capacitor banks; they are classed C2 according to standard IEC 62271-100.
Tests carried out according to the standard for breaking at 400 A with making
and breaking cycles in case of a capacitor bank with a making current of 20 kA.
Additional tests have been carried out: please consult us.

10
SF1 and SFset General characteristics (cont.)
circuit breakers
fixed version

SFset

PE56504
24 36 12 17.5 24

50 70 28 38 50
125 170 75 95 125
b b b b b b
b b b b b b b b b b b b b b b b
b b b b b b b b b b b b b b b
12.5 16 20 25 12.5 16 20 25 25 12.5 20 25 12.5 16 20 25
12.5 16 20 25 12.5 16 20 25 25 12.5 20 25 12.5 16 20 25
31.3 40 50 62.5 31.3 40 50 62.5 62.5 31.3 50 62.5 31.3 40 50 62.5
32.5 41.6 52 65 32.5 41.6 52 65 65 32.5 52 65 32.5 41.6 52 65
b b b b b
b b b b b
b b b b b
b b b
b b b b b b b b b b b b
b b b b b b b b
b b b
b b b b
b b b b b b b b b b b b b b
b b b b b b b b b b b b b b
b b b b b b b b b b b b b b
b b b b b b b b b b b b
< 50 < 50
< 60 < 60
< 65 < 65
25 to +40 25 to +40
M2 M2
10,000 10,000
E2 E2
C2 C2

11
 SF1 and SFset Description of functions
circuit breakers RI stored energy operating mechanism
fixed version Wiring diagram

Manual or electrical operation of the RI stored energy

PE55826

operating mechanism
This gives the device an opening and closing speed that is independent of the
operator whether the order is electrical or manual.
The electrical control mechanism carries out reclosing cycles and is automatically
recharged by a geared motor each time after closing.
It consists of:
b the stored energy operating mechanism which stores in springs the energy
required to open and close the device
b a manual lever-operated spring arming device
b a geared electrical arming device which automatically re-arms the control
mechanism as soon as the circuit breaker is closed (optional)
b manual order devices by push buttons on the front panel of the device
b an electrical remote closing device containing a release with an antipumping relay
b an electrical opening order device comprising one or several release units which
can be of the following type:
v shunt opening
v undervoltage
v Mitop, a low consumption release, used only with the Sepam 100 LA
protection relay.
b an operation counter
b an open/closed position indicator device with a mechanical indicator
b a device for indicating charged operating mechanism status by mechanical
indicator and electrical contact (optional)
b a module of 14 auxiliary contacts whose availability varies according
to the diagram used.

Wiring diagram (principle)

DE58090EN

Close CB

Open CB

M3

YF + Mitop
anti-pumping YO1 YO2 YM

Motor Shunt closing Control Shunt Under- Low energy Changeover NO NC

release mechanism opening voltage release contact contacts contacts
+ anti-pumping armed release release (Mitop)
system indicator contact

Remote control

12
 SF1 and SFset Description of functions
circuit breakers Opening circuit
fixed version

Composition
DE57612EN

The opening circuit can be produced using the following components:

b a shunt opening release (on energizing) (YO1)
b a second shunt opening release (on energizing) (YO2)
b undervoltage release (YM)
(2) (1) or (3) b low energy release (Mitop).
Note: see the table of the releases combinations page Order form .

Shunt opening release (YO1 and YO2)

Energizing this unit causes instant opening of the circuit breaker.
Characteristics
Power supply See Order form page
Threshold V AC 0.85 to 1.1 Ur
V DC 0.7 to 1.1 Ur
Consumption V AC 160 VA
V DC 50 W
Operating mechanism

Undervoltage release (YM)

DE58092

This release unit causes the systematic opening of the circuit breaker when its
supply voltage drops below a value less than 35% of the rated voltage, even if this
drop is slow and gradual. It can open the circuit breaker between 35% and 70% of
its rated voltage. If the release unit is not supplied power, manual or electrical closing
of the circuit breaker is impossible. Closing of the circuit breaker is compulsory when
Shunt opening release (1) the supply voltage of the release unit reaches 85% of its rated voltage.
Characteristics
DE58093

Power supply See Order form page

Threshold Opening 0.35 to 0.7 Ur
Closing 0.85 Ur
Consumption Triggering V AC 400 VA
V DC 100 W
Latched V AC 100 VA
Undervoltage release (2) V DC 10 W
DE58094

Low energy release (Mitop)

This specific release unit comprises a low consumption unit and is specifically used
for Sepam 100LA self-powered relays.
Characteristics
Low energy release (3) Power supply Direct current
Threshold 0.6 A < I < 3 A
Any tripping due to the Mitop release unit is momentarily indicated by an SDE type
changeover contact (option).

13
 SF1 and SFset Description of functions
circuit breakers Remote control
fixed version

Function
DE57604

Remote control enables the remote opening and closing of the circuit breaker.

Composition
The remote control mechanism comprises:
b an electrical motor with gearing
b a shunt closing release (YF) combined with an anti-pumping device
b an operation counter.

Electrical motor with gearing (M)

The electrical motor carries out the automatic rearming of the stored energy unit as
soon as the circuit breaker is closed. This allows the instant reclosing of the device
after opening. The arming lever is only used as a backup operating mechanism
in the case of the absence of the auxiliary power supply.
The M3 contact indicates the end of arming operations.
Characteristics
Power supply See Order form page
Operating mechanism Threshold V AC/V DC 0.85 to 1.1 Ur
Consumption V AC 380 VA
V DC 380 W
DE58096

Shunt closing release (YF)

This release allows the remote closing of the circuit breaker when the operating
mechanism is armed.
Electrical motor with gearing (4)
Characteristics
Power supply See Order form page
DE58092

Threshold V AC 0.85 to 1.1 Ur

V DC 0.85 to 1.1 Ur
Consumption V AC 160 VA
V DC 50 W
The shunt closing release is combined with an anti-pumping relay that enables priority
Shunt closing release (5) to be given to opening in the case of a permanent closing order. This thus avoids
the device being caught in an uncontrolled opening-closing cycle.
DE58097

Operation counter
The operation counter is visible on the front panel.
Operation counter (6)
It displays the number of switching cycles (CO) that the device has carried out.

14
 SF1 and SFset Description of functions
circuit breakers Indication and locking/interlocking
fixed version

Open/closed auxiliary contacts

DE57491

The number of contacts available depends on the options chosen on the operating
mechanism.
In the basic configuration, the circuit breakers operating mechanism comprises
a total of:
b 5 normally closed contacts (NC)
b 5 normally open contacts (NO)
b 1 changeover contact (CHG).
The usage procedure for auxiliary contacts is given in the following table:
Options
NC contact NO contact
Shunt opening release (each one) 0 1
Undervoltage release 0 0
Low energy release (Mitop) 0 0
In order to know the final number of available contacts, you must deduct the total
number of contacts included in the circuit breaker (5 NC + 5 NO + 1 CHG),
the number of contacts used given in the table above.
E.g.: a circuit breaker equipped with a remote control and a shunt trip unit has
Operating mechanism the following available contacts:
5 NC + 4 NO + 1 CHG.
With a undervoltage release instead of the shunt trip, this circuit breaker would have
DE58098

the following available contacts:

5 NC + 5 NO + 1 CHG.
Shunt opening release combination
1st release Shunt opening Undervoltage release Mitop
Auxiliary contacts (7) release YO1 YM
2nd release
Without 5NC + 4NO + 1CHG 5NC + 5NO+ 1CHG 5NC + 5NO + 1CHG
DE58099

Shunt opening release 5NC + 3NO + 1CHG 5NC + 4NO+ 1CHG 5NC + 4NO + 1CHG
YO2
Undervoltage release 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG
YM
Mitop 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG

Locking the circuit breaker in the open position

This key-operated device allows the circuit breaker to be locked in the open position.
The circuit breaker is locked in the open position by blocking the opening push button
in the engaged position.
Keylocking kit (8)
Locking is achieved using a Profalux or Ronis captive key type keylock.

15
 SF1 and SFset Protection, monitoring and control
circuit breakers VIP300 protection unit
fixed version

The SFset circuit breaker has an integrated and independent

PE56504

protection system
The SFset circuit breaker comprises an SF1 into which is integrated a protection system
comprising:
b a set of current sensors installed on the lower current terminals of the pole units.
Two interchangeable sensors, CSa and CSb, sufficient to cover all requirements
from 10 A to 1250 A.
b a VIP type protection relay mounted on the control unit.
b a Mitop low consumption, release unit installed on the switching device.
The unit is fully independent and functions without an auxiliary power supply.
Operating principle
The protection system is supplied power by sensors which supply:
b the current information, processed by the protection unit
b the electrical power required for the whole protection system to operate ;
VIP unit and Mitop release.
SFset with a VIP protection unit installed on the front panel All settings are visible and accessible from the front of the device.

VIP300P and VIP300LL independent protection unit

PE55772

The VIP300 unit is intended to be installed on distribution networks. It can be used

to protect an MV/LV transformer, to protect the head of an industrial installation,
but also to protect a branch.
The VIP300 provides protection against phase-to-phase faults and against earthing
faults. The choice of trip curves and the large number of settings enable it to be used
in a large number of discrimination arrangements.
The VIP300 is an independent unit supplied power from the current sensors;
it does not require an auxiliary power supply. It activates a Mitop release unit.
The VIP300 exists in 2 models:
b VIP300P: phase protection
b VIP300LL: phase and earthing protection.
DE57402

DE57403

Mitop
VIP300LL protection unit

VIP300
t>

t >>
I
1,2 Is 10 Is I >>
Simplified connection arrangement Phase and earthing protection curve

Phase protection (VIP300P, VIP300LL)

Phase protection has two independently adjustable thresholds:
b the lower threshold can be chosen to be either definite time or inverse definite time.
It can be executed according to the RI curve.
b the upper threshold is inverse definite time.
The definite time curves are in conformity with standard IEC 60255-3.
They are either of type inverse (SI), very inverse (VI) and extremely inverse (EI).
Earthing protection (VIP300LL)
Earthing full protection functions with the measurement of residual current:
this is carried out based on the sum of secondary currents in the sensors.
As for phase protection, earthing protection has two independently adjustable
thresholds.
Indication
Two indicators show the origin of the release (phase or earth).
They stay in position after breaking the release unit power supply.
Two LED indicator lights (phase and earth) show that the lower threshold
has been exceeded and that the time delay has been started.

16
 SF1 and SFset Protection, monitoring and control
circuit breakers Trip curves
fixed version VIP300P and VIP300LL

Trip curves
DE57404

t> t>

t >> t >>

Is 1.2 Is 10 Is I >> Is I> I >>

With a definite time lower threshold With an inverse definite time lower threshold

Definite time curves

DE7405

t (s) t (s)
100 100

10 10
6 6
4
3 4
2 3
1.5 2
1 1 1 1.5
1
0.6
0.4 0.6
0.3 0.4
0.2 0.3
0.15 0.2
0.1 0.1 0.1 0.15
0.07 0.1
0.05 0.07
0.05

I/Is I/Is
0.01 0.01
1 10 100 1 1.2 Is 10 100
RI curve SI curve
DE57406

t (s) t (s)
1000 1000

100 100

10 10

6
4
3 6
1 2 1 4
1.5 3
1 2
0.6 1.5
0.4 1
0.3 0.6
0.1 0.2 0.1 0.4
0.15 0.3
0.1 0.2
0.07 0.15
0.05 0.1
I/Is 0.07 I/Is
0.01 0.01 0.05
1 1.2 Is 10 100 1 1.2 Is 10 100
VI curve EI curve

17
 SF1 and SFset Protection, monitoring and control
circuit breakers Current sensors and test unit for VIP300
fixed version

CSa and CSb current sensors for the VIP300

PE55773

In order to achieve the specified performance levels, the VIP300 protection unit
must be used with the specified sensors. The combination of the unit/sensor
is essential in order to comply with characteristics and in particular with:
b operation throughout the whole range
b response time
b accuracy
b short circuit thermal withstand.
Two interchangeable sensors, CSa and CSb, suffice to cover all requirements
from 10 A to 1250 A.

Sensor selection Service current (Is)

CSa 10 A to 200 A
CSb 63 A to 1250 A

Cs type current sensors

VAP6 test unit
VIP type protection units have a test, socket to connect a VAP6 test unit.
This portable unit with its own power supply enables the correct functioning
PE55774

of the protection unit to be checked.

VAP6 test unit

18
 SF1 and SFset Dimensions
circuit breakers
fixed version

Basic fixed unit

Operating mechanism on the right hand side (A1)
SF1, SFset SF1 SFset
DE57407

E E P/D P/D

350 350

L/W 270

Operating mechanism on the left hand side (B1)

SF1 SFset SF1, SFset
DE57408

P/D P/D E E

350 350

270 L/W

Operating mechanism on the front (C1)

SF1, SFset SF1 SFset
DE57409

E E P/D 270 P/D 270

345 345

L/W

Dimensions and weights

SF1 SFset
Rated voltage (kV) Dimensions (mm) Weight (kg) Dimensions (mm) Weight (kg)
H W D E H W D E
Operating mechanism on the right or left
17.5 750 993 290 220 78 750 993 420 220 88
24 750 1143 290 280 80 750 1143 420 280 90
36 750 1560 365 380 88
Operating mechanism on the front
17.5 745 766 490 220 78 745 766 620 220 88
24 745 886 490 280 80 745 886 620 280 90
36 745 927 559 350 85
36 745 1260 565 380 88
For SF circuit breakers with SM6, consult us.

19
 SF1 and SFset Dimensions (cont.)
circuit breakers
fixed version

Fixed unit with support frame

Operating mechanism on the right hand side (A1)
SF1, SFset SF1 SFset
DE57412

E E P/D P/D

H (1)

775 (1) 775 (1)

L/W

Operating mechanism on the left hand side (B1)

SF1 SFset SF1, SFset
DE57411

P/D P/D E E

H (1)

775 (1) 775 (1)

L/W

Operating mechanism on the front (C1)

SF1, SFset SF1 SFset
DE57410

E E P/D P/D

H (1)

775 (1) 775 (1)

L/W

Dimensions and weights

SF1 SFset
Rated voltage (kV) Dimensions (mm) Weight (kg) Dimensions (mm) Weight (kg)
H W D E H W D E
Operating mechanism on the right or left hand side
17.5 1175 1065 600 220 103 1175 1065 600 220 103
24 1175 1215 600 280 105 1175 1215 600 280 105
36 1175 632 600 380 113
Operating mechanism on the front
17.5 1175 853 600 220 103 1175 853 649 220 103
24 1175 973 600 280 105 1175 973 649 280 105
36 1175 1347 600 380 113
(1) Additional holes, provided on the fixed support frame allow the device to be positioned 215 mm lower.

20
 SF1 and SFset Dimensions (cont.)
circuit breakers
fixed version

Connection
Top
Ir y 630 A
SF1, SFset (A) SF1, SFset (B)
20 24 20
DE57413-A

40

DE57414

DE57413-B
M8 kA M8
25

20 (B)
56 56
16 20

17 17
8 13 +0.2
0 12,5 (A) 8 +0.2
13 0

17,5 24 36 kV

Ir = 1250 A
SF1, SFset (B)
20 40
DE57413-B

DE57415

M8 kA
25

20
56
20 16 (B)

17 +0.2 12,5
8 13 0

17,5 24 36 kV

Bottom
SF1, insulation y 125 kV impulse SF1, insulation y 170 kV impulse SFset
2 M8 25 0,5 2 M8
DE57416

DE57417

DE57418

2 10,5 52
20
10
18 40 40
20 20
60
75

Note: recommended connection screw M8 class 8.8.

Tightening torque: 28 Nm with contact washer.

21
SF1 and SFset Order form
circuit breakers SF1 lateral/frontal fixed up to 36 kV
fixed version

Only one of the boxes (ticked X or filled by Basic fixed circuit breaker Quantity
the needed value) have to be considered between each
Rated voltage Ur (kV)
horizontal line.
Green box X corresponds to none priced functions. Impulse voltage Up (kVbil)

Short-circuit current Isc (kA)

Rated current Ir (A)

Frequency 50 Hz 60 Hz

Operating mechanism position A1 B1 C1

Colour for push buttons and indicators
Push buttons open/close: Red/black
Indicator open/close: Black/white
Operating mechanism charged/discharged: White/yellow

Circuit breaker options

1st opening release (see possible choices in combination table below)
Shunt opening release YO1
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Mitop Without contact With contact

2nd opening release (see possible choices in combination table below)

Shunt opening release YO2
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Mitop Without contact With contact

Remote control
Electrical motor M 2432 Vdc 110127 Vdc/ac
4860 Vdc/ac 220250 Vdc/ac
Shunt closing release YF
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

Low voltage wiring connection Male plug (1.2 m) Female socket (2 m)

Locking C.B. in open position Ronis Profalux
Support frame Low (560 mm) High (775 mm)
Leaflets language French English
Pressure switch (not available for all electrical characteristics)

Releases combinations table

Shunt opening releases YO1/YO2 1 2 1 1
Undervoltage release YM 1 1 1
Mitop 1 1 1

22
SF1 and SFset Order form
circuit breakers SFset lateral/frontal fixed up to 24 kV
fixed version

Only one of the boxes (ticked X or filled by Basic fixed circuit breaker Quantity
the needed value) have to be considered between each
Rated voltage Ur (kV)
horizontal line.
Green box X corresponds to none priced functions. Impulse voltage Up (kVbil)

Short-circuit current Isc (kA)

Rated current Ir (A)

Frequency 50 Hz 60 Hz

Operating mechanism position A1 B1 C1

Colour for push buttons and indicators
Push buttons open/close: Red/black
Indicator open/close: Black/white
Operating mechanism charged/discharged: White/yellow

Control unit and sensors

VIP 300P (not available for all CSa 200/1 Is = 10 to 50 A Is = 40 to 200 A
electrical characteristics) CSb 1250/1 Is = 63 to 312 A Is = 250 to 1250 A

VIP 300LL CSa 200/1 Is = 10 to 50 A Is = 40 to 200 A

CSb 1250/1 Is = 63 to 312 A Is = 250 to 1250 A

Circuit breaker options

2nd opening release (see possible choices in combination table below)
Shunt opening release YO2
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

Remote control
Electrical motor M 2432 Vdc 110127 Vdc/ac
4860 Vdc/ac 220250 Vdc/ac
Shunt closing release YF
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

Low voltage wiring connection Male plug (1.2 m) Female socket (2 m)

Locking C.B. in open position Ronis Profalux
Support frame Low (560 mm) High (775 mm)
Test unit (VAP 6)
Leaflets language French English
Pressure switch (not available for all electrical characteristics)

Releases combinations table

Mitop 1 1 1
Shunt opening release YO2 1
Undervoltage release YM 1

23
24
SF circuit breakers SF2 circuit breakers
fixed version

General presentation 2
Panorama 4
SF1 and SFset circuit breakers fixed version 7
Presentation 26
General characteristics 27
Description of functions 28
GMH stored energy operating mechanism 28
Wiring diagram 28
Opening circuit 29
Remote control 30
Indication and locking/interlocking 31
Dimensions 32
Order form 33
SF F400 circuit breakers withdrawable version 35

25
 SF2 circuit breakers Presentation
fixed version

Description of the device

PE56501

The basic fixed version of the SF circuit breaker comprises:

b 3 main independent poles, that are mechanically linked and each comprising
a sealed pressure system type insulating enclosure. The sealed enclosure is filled
with low pressure SF6 gas
b a GMH stored energy electrical operating mechanism.
This gives the device an opening and closing speed that is independent
of the operator, for both electrical and manual orders.
The circuit breaker can be remotely controlled and it is possible to carry out reclosing
cycles.
b a front panel housing the manual operating mechanism and status indicators
b upstream and downstream terminals for the power circuit connection
b a terminal block for connection of external auxiliary circuits.
The SF circuit breaker is only available with a frontal operating mechanism.
Each device can be optionally equipped with:
b a support frame fitted with rollers and floor securing brackets for a fixed installation
b locking of the circuit breaker in the open position by a keylock installed on the
control panel
b a pressure switch for the high performance versions
b a Harting 42-pin type LV connector.

Applications
SF circuit breakers are 3-pole MV circuit breakers for indoor installation.
They are mainly used for switching and protection of networks from 24 to 40.5 kV
in primary and secondary power distribution.
The autocompression breaking technique used in these circuit breakers means that
making or breaking all types of compacitive or inductive currents can be achieved
without dangerous overvoltages for the switchgear connected to the network.
The SF circuit breaker is therefore well suited to operating capacitor banks.

26
SF2 circuit breakers General characteristics
fixed version

Electrical characteristics according to IEC 62271-100

SF2
Rated voltage Ur kV 50/60 Hz 24 36 40.5
Insulation voltage
- power frequency withstand Ud kV 50 Hz 1min 50 70 95
- lightning impulse withstand Up kV peak 125 170 185
Rated current Ir A 630 b b b b
1250 b b b b
2500 b b b b b b b b
3150 b b
Short circuit current Isc kA 12.5 25 31.5 40 25 31.5 40 31.5
Short time withstand current Ik/tk kA/3 s 12.5 25 31.5 40 25 31.5 40 31.5
Short-circuit making current Ip kA peak 50 Hz 31.3 63 79 100 62.5 79 100 78.8
60 Hz 32.5 65 82 104 65 82 104 81.9
Rated switching sequence O-3 min-CO-3 min-CO b b b b b b b b
O-0.3 s-CO-3 min-CO b b b b b b
O-0.3 s-CO-15 s-CO b b b b
Phase to phase mm 300 b b b b
400 b b b
457 b
Operating mechanism Frontal b b b
Operating times Opening (ms) < 50
Breaking (ms) < 60
Closing (ms) < 65
Service temperature T C 25 to +40
Mechanical endurance Class M2
Number of switching operations 10,000
Electrical endurance Class E2
Capacitive current breaking capacity Class C2

b Available
Not available.

Specific applications
Switching and protection of capacitor banks
SF range circuit breakers are particularly well suited to switching and protection
of capacitor banks; they are classed C2 according to standard IEC 62271-100.
Tests carried out according to the standard for breaking at 400 A with making
and breaking cycles in case of a capacitor bank with a making current of 20 kA.
Additional tests have been carried out: please consult us.

27
 SF2 circuit breakers Description of functions
fixed version GMH stored energy operating mechanism
Wiring diagram

Operation of the electrical GMH stored energy mechanism

028368

This gives the device an opening and closing speed that is independent of the
operator whether the order is electrical or manual.
The electrical control mechanism carries out reclosing cycles and is automatically
recharged by a geared motor each time after closing.
It consists of:
b the stored energy operating mechanism which stores in springs the energy
required to open and close the device
b a manual lever arming device for the springs
b an electrical arming device with a motor to automatically rearm the control
mechanism as soon as the circuit breaker is closed (optional)
b manual push-button controls on the front face of the circuit breaker (red and black)
b an electrical remote-closing device comprising a release and an anti-pumping relay.
b an electrical opening device comprising one or several releases of the following
type:
v shunt opening
v undervoltage
v Mitop, low energy release only used Sepam 100 LA protection relays
b an operation counter
b an open/closed position indicator with a mechanical indicator (black and white)
b an armed control mechanism status indicator with a mechanical indicator
and an electrical contact (optional)
b a block of 14 auxiliary contacts, available according to the wiring layout used
b a pressure switch contact activated by a drop in gas pressure (optional: single
or double threshold pressure switch)

Wiring diagram (principle)

DE57420EN

Close CB

Open CB

M3

YF + Mitop
anti-pumping YO1 YO2 YM

Motor Shunt closing Control Shunt Under- Low energy Changeover NO NC Pressostat
release mechanism opening voltage release contact contacts contacts
+ anti-pumping armed release release (Mitop)
system indicator contact

Remote control

28
 SF2 circuit breakers Description of functions
fixed version Opening circuit

Composition
DE57421EN

The opening circuit can be produced using the following components:

b a shunt opening release (on energizing) (YO1)
b a second shunt opening release (on energizing) (YO2)
b undervoltage release (YM)
(1) b low energy release (Mitop).
Note: see the table of the releases combinations page Order form .

Shunt opening release (YO1 and YO2)

Energizing this unit causes instant opening of the circuit breaker.
(1) or (2) Characteristics
or (3) Power supply See Order form page
Threshold V AC 0.85 to 1.1 Ur
V DC 0.7 to 1.1 Ur
Consumption V AC 160 VA
Operating mechanism V DC 50 W
DE58092

Undervoltage release (YM)

This release unit causes the systematic opening of the circuit breaker when its
supply voltage drops below a value less than 35% of the rated voltage, even if this
drop is slow and gradual. It can open the circuit breaker between 35% and 70% of
its rated voltage. If the release unit is not supplied power, manual or electrical closing
Shunt opening release (1) of the circuit breaker is impossible. Closing of the circuit breaker is compulsory when
the supply voltage of the release unit reaches 85% of its rated voltage.
DE57390

Characteristics
Power supply See Order form page
Threshold Opening 0.35 to 0.7 Ur
Closing 0.85 Ur
Consumption Triggering V AC 400 VA
V DC 100 W
Undervoltage release (2) Latched V AC 100 VA
V DC 10 W
DE57391

Low energy release (Mitop)

This specific release unit comprises a low consumption unit and is specifically used
for Sepam 100LA self-powered relays.
Characteristics
Power supply Direct current
Low energy release (3)
Threshold 0.6 A < I < 3 A
Any tripping due to the Mitop release unit is momentarily indicated by an SDE type
changeover contact (option).

29
 SF2 circuit breakers Description of functions
fixed version Remote control

Function
DE57422

Remote control enables the remote opening and closing of the circuit breaker.

Composition
The remote control mechanism comprises:
b an electrical motor with gearing
b a shunt closing release (YF) combined with an anti-pumping device
b an operation counter.

Electrical motor (M)

The electrical motor carries out the automatic rearming of the stored energy unit as
soon as the circuit breaker is closed. This allows the instant reclosing of the device
after opening. The arming lever is only used as a backup operating mechanism
in the case of the absence of the auxiliary power supply.
The M3 contact indicates the end of arming operations.
Characteristics
Operating mechanism
Power supply See Order form page
Threshold V AC/V DC 0.85 to 1.1 Ur
DE57392

Consumption V AC 380 VA
V DC 380 W

Electrical motor (4) Shunt closing release (YF)

This release allows the remote closing of the circuit breaker when the operating
mechanism is armed.
DE58092

Characteristics
Power supply See Order form page
Threshold V AC 0.85 to 1.1 Ur
V DC 0.85 to 1.1 Ur
Consumption V AC 160 VA
Shunt closing release (5)
V DC 50 W
The shunt closing release is combined with an anti-pumping relay that enables priority
DE57393

to be given to opening in the case of a permanent closing order. This thus avoids
the device being caught in an uncontrolled opening-closing cycle.

Operation counter (6)

Operation counter
The operation counter is visible on the front panel.
It displays the number of switching cycles (CO) that the device has carried out.

30
 SF2 circuit breakers Description of functions
fixed version Indication and locking/interlocking

Open/closed auxiliary contacts

DE57423

The number of contacts available depends on the options chosen on the operating
mechanism.
In the basic configuration, the circuit breakers operating mechanism comprises
a total of:
b 5 normally closed contacts (NC)
b 5 normally open contacts (NO)
b 1 changeover contact (CHG).
The usage procedure for auxiliary contacts is given in the following table:
Options
NC contact NO contact
Shunt opening release (each one) 0 1
Undervoltage release 0 0
Low energy release (Mitop) 0 0
In order to know the final number of available contacts, you must deduct the total
number of contacts included in the circuit breaker (5 NC + 5 NO + 1 CHG),
the number of contacts used given in the table above.
Operating mechanism E.g.: a circuit breaker equipped with a remote control and a shunt trip unit has
the following available contacts:
5 NC + 4 NO + 1 CHG.
DE57394

With a undervoltage release instead of the shunt trip, this circuit breaker would have
the following available contacts:
5 NC + 5 NO + 1 CHG.
Shunt opening release combination
Auxiliary contacts (7) 1st release Shunt opening Undervoltage release Mitop
release YO1 YM
2nd release
DE57395

Without 5NC + 4NO + 1CHG 5NC + 5NO+ 1CHG 5NC + 5NO + 1CHG
Shunt opening release 5NC + 3NO + 1CHG 5NC + 4NO+ 1CHG 5NC + 4NO + 1CHG
YO2
Undervoltage release 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG
YM
Mitop 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG
Keylocking kit (8)

Locking the circuit breaker in the open position

This key-operated device allows the circuit breaker to be locked in the open position.
The circuit breaker is locked in the open position by blocking the opening push button
in the engaged position.
Locking is achieved using a Profalux or Ronis captive key type keylock.

31
 SF2 circuit breakers Dimensions
fixed version

Basic fixed unit

P/D 300
DE57424

E E 190

372

L/W

Fixed unit with a support frame

P/D 300
DE57425

E E
190

630

L/W 644

Connection
630, 1250 A (24-36 kV) 2500, 3150 A (24-36 kV) 2000, 2500 A (40.5 kV)
35 78 2 M12
DE57426

DE57419

32,5

10 70 30
100
90 30 20 60
35
8 13 49,5
18,5 90

63 70

26
26 47 10 117

Dimensions and weights

Basic fixed unit Fixed unit with support frame
Rated current Rated voltage Dimensions (mm) Weight Dimensions (mm) Weight
(A) (kV) H L P E (kg) H L P E (kg)
630, 1250 24 825 910 750 300 159 1030 910 750 300 179
36 825 1110 750 400 212 1030 1110 750 400 239
40.5 825 1224 750 457 242 1030 1224 750 457 272
2500, 3150 24 942 910 777 300 174 1147 910 777 300 194
36 942 1110 777 400 227 1147 1110 777 400 254
40.5 942 1224 777 457 242 1147 1224 777 457 272

32
SF2 circuit breakers Order form
fixed version SF2 fixed up to 40.5 kV

Only one of the boxes (ticked X or filled by Basic fixed circuit breaker Quantity
the needed value) have to be considered between each
Rated voltage Ur (kV)
horizontal line.
Green box X corresponds to none priced functions. Impulse voltage Up (kVbil)

Short-circuit current Isc (kA)

Rated current Ir (A)

Frequency 50 Hz 60 Hz
Colour for push buttons and indicators
Push buttons open/close: Red/black
Indicator open/close: Black/white
Operating mechanism charged/discharged: White/yellow

Circuit breaker options

1st opening release (see possible choices in combination table below)
Shunt opening release YO1
24 Vdc 60 Vdc 220 Vdc 250 Vac (50 Hz)
32 Vdc 100-109 Vdc 110 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 100-127 Vdc 220 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
32 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Mitop Without contact With contact

2nd opening release (see possible choices in combination table below)

Shunt opening release YO2
24 Vdc 60 Vdc 220 Vdc 250 Vac (50 Hz)
32 Vdc 100-109 Vdc 110 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 100-127 Vdc 220 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
32 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Mitop Without contact With contact

Remote control
Electrical motor M 2432 Vdc 110127 Vdc/ac
4860 Vdc/ac 220250 Vdc/ac
Shunt closing release YF
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
32 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

Low voltage wiring connection Male plug (1.2 m) Female socket (2 m)

Locking C.B. in open position Ronis Profalux
Pressure switch
Support frame
Leaflets language French English

Releases combinations table

Shunt opening releases YO1/YO2 1 2 1 1
Undervoltage release YM 1 1
Mitop 1 1

33
34
SF circuit breakers SF F400 circuit breakers
withdrawable version

General presentation 2
Panorama 4
SF1 and SFset circuit breakers fixed version 7
SF2 circuit breakers fixed version 25
Presentation 36
General characteristics 37
Description of functions 38
Racking-in 38
MV and LV connection 40
GMH stored energy operating mechanism 41
Wiring diagram 41
Opening circuit 42
Remote control 43
Indication and locking/interlocking 44
Safety functions 45
Dimensions 46
Order form 48

35
 SF F400 circuit breakers Presentation
withdrawable version

Device description
PE56502

The basic withdrawable version of the SF circuit breaker comprises:

b the circuit breaker unit with its control mechanism:
v 3 main independent poles, that are mechanically linked and each comprising
a sealed pressure system type insulating enclosure. The sealed enclosure is filled
with low pressure SF6 gas
v a GMH stored energy electrical operating mechanism
This gives the device an closing and opening speed that is independent
of the operator, whether the control order is electrical or manual.
When remotely controlled, the circuit breaker allows reclosing cycles
to be performed
v a front face with status indicators
b racking components:
v the circuit breaker is equipped with racking arms and clusters. It is mounted
on a racking/unracking unit with a threaded shaft actuated by a crank which includes
all of the safety interlocking systems
v a Harting type male LV connector for external auxiliary circuits.
The SF circuit breaker is only available with front controls.
Each device can be fitted with the following options:
b position locking of the circuit breaker:
v open, by a keylock installed on the control panel
v racked out, by a keylock installed on the racking device
b the M1 and M2 basic cassettes comprising:
v a metal structure and one guide rail
v fixed connector fingers insulated by bushings
v metal insulating shutters for the MV part
v safety interlocking systems
v Harting type female LV connector
v indicator contacts for circuit breaker racked-in or racked-out positions
(4 NO + 4NC)
v a circuit breaker control mechanism spring discharge system
v a circuit breaker racking-in blocking mechanism
v an equipped door
v a foolproofing system for the circuit breaker rating
b M1 et M2 cassettes (optional):
v a VPIS kit (voltage indicator).

Applications
SF circuit breakers are 3-pole MV circuit breakers for indoor installation.
They are mainly used for switching and protection of networks from 24 to 40.5 kV
in primary and secondary power distribution.
The autocompression breaking technique used in these circuit breakers means that
making or breaking all types of compacitive or inductive currents can be achieved
without dangerous overvoltages for the switchgear connected to the network.
The SF circuit breaker is therefore well suited to operating capacitor banks.

36
SF F400 circuit breakers General characteristics
withdrawable version

Electrical characteristics according to IEC 62271-100

SF F400
Rated voltage Ur kV 50/60 Hz 24 36 40.5
Insulation voltage
- power frequency withstand Ud kV 50 Hz 1min 50 70 95
- lightning impulse withstand Up kV peak 125 170 185
Rated current Ir A 1250 b b b b
2500 b b b
3150 b
Short circuit current Isc kA 40 25 31.5 40 31.5
Short time withstand current Ik/tk kA/3 s 40 25 31.5 40 31.5
Short-circuit making current Ip kA peak 50 Hz 100 62.5 79 100 79
60 Hz 104 65 82 104 82
Rated switching sequence O-3 min-CO-3 min-CO b b b b b
O-0.3 s-CO-3 min-CO b b b
O-0.3 s-CO-15 s-CO b
Phase to phase mm 300 b b b b b
Operating mechanism Frontal b b b b b
Operating times Opening (ms) < 50
Breaking (ms) < 60
Closing (ms) < 65
Service temperature T C 25 to +40
Mechanical endurance Class M2
Number of switching operations 10,000
Electrical endurance Class E2
Capacitive current breaking capacity Class C2

b Available
Not available.

Specific applications
Switching and protection of capacitor banks
SF range circuit breakers are particularly well suited to switching and protection
of capacitor banks; they are classed C2 according to standard IEC 62271-100.
Tests carried out according to the standard for breaking at 400 A with making
and breaking cycles in case of a capacitor bank with a making current of 20 kA.
Additional tests have been carried out: please consult us.

37
 SF F400 circuit breakers Description of functions
withdrawable version Racking-in

Overall composition
DE57396

The racking-in/racking-out function is achieved by:

b the SF F400 withdrawable circuit breaker with its LV connector (moving part)
b the M1 or M2 cassettes with their bushings (fixed part).

Switching the circuit breaker

The withdrawable circuit breaker can be moved between three stable positions:
b service position: the circuit breaker racked-in and locked in position,
the LV connector is connected
b test position: the circuit breaker is racked-out and locked in position,
the LV connector is connected
b disconnected position: the circuit breaker is racked-out and locked in position,
the LV connector is disconnected.

SF F400 circuit breaker safety functions

A racking system with a threaded shaft makes it easier to rack-in and rack-out.
DE57430

Test position contact

This is activated when the circuit breaker is in the test or service positions.
Earthing is achieved throughout the operation through the racking carriage wheels.
Interlocking
In conformity with standards IEC 62271-100 and 62271-200, the following interlocks
are available:
Service position b prohibiting racking-in or racking-out if the circuit breaker is not in the open position
b prohibiting racking-in of the circuit breaker if the LV connector is not connected
DE57429

b prohibiting disconnecting of the LV connector if the circuit breaker is not racked-out.

Interlocking with the cubicle door
The racking base is equipped with a device that allows interlocking between
racking-out of the circuit breaker and the cubicle door.
b only possible to rack-in the circuit breaker if the door is closed
b only possible to open the door if the circuit breaker is racked-out.
This device must be disabled if this interlocking function is not present.
Test position
DE57428

M1 and M2 cassettes safety features

The M1 or M2 cassettes are fitted with the SF F400 circuit breaker and comprise
the following safety features for racking-in.
A metal structure with one guide rail
The rail guides the circuit breaker during racking-in/racking-out operations.
disconnected position
Fixed connector fingers, insulated by bushings
The three ends of the circuit breaker, with their racking clusters, make the contact
with these three fingers.
PE50198

Metal insulating shutters for the MV part

Protective shutters mounted on the structure stop fingers from accessing the racking
mechanism when the circuit breaker is extracted (protection index: IP2X).
Safety interlocking systems
When carrying out maintenance operations it is possible to:
b padlock the shutters in the locked position
b unlock the fixed contact access mechanism.
A control spring discharge system
The springs of the circuit breaker mechanism are automatically discharged when
it is extracted from the cassette. This function avoids any risk of nuisance closing
of the circuit breaker.
Volets de protection Foolproofing system
This allows the circuit breaker rating to be matched to the cassette rating.
This system is mounted on the cassette side. The panel builder must ensure
that the right circuit breaker rating is being used.

Protective shutters

38
 SF F400 circuit breakers Description of functions
withdrawable version Racking-in (cont.)

Locking/interlocking functions
Possibilities for padlocking
PE50201

For further operator safety it is possible to use a padlock:

b on the connector to lock the selector
b on the shutter protecting the mechanical opening pushbutton
b on the shutter opening mechanism in the circuit breaker compartment
b on the rotary voltage transformer switching mechanism.
PE50202

A mechanism to prohibit racking-in of the moving part

A mechanism associated with a padlock or a keylock prohibits the racking-in
of the moving part. Locking is either achieved via:
b 1 to 3 padlocks, not supplied
b 1 keylock (optional).

A blocking system for the circuit breaker opening order, when it is closed
PE50204

This device can also be used as an additional way of prohibiting racking-in and out.
A transparent shutter blocks access to the opening and closing pushbutton.
The device allows independent locking of the opening or closing button.
It is often associated with an electrical motor (M). Locking is achieved by
a padlock (not supplied) mounted on the shutter protecting the mechanical
opening pushbutton.

A system to prohibit disconnection of the moving part

PE50205

This keylocking system prohibits disconnection of the moving part. It may be used
for a circuit breaker or for a racking base.

Optional accessories
b a self-adhesive front plate shows circuit breaker racking-in and racking-out
operations. It is systematically delivered when the circuit breaker is ordered
with the cassette or can be ordered separately.
b 4 racked-in/racked-out position contacts.
b 1 position contact for the cassette locked in the racked-in/racked-out position.
b a keylocking system (Ronis or Profalux) for the circuit breaker in the racked-in
or racked-out position.

39
SF F400 circuit breakers Description of functions
withdrawable version MV and LV connection

MV Connection
The customer connection is easily carried out from the back of M1 and M2 cassettes
using the upper and lower bushings.

PE50194

PE50195
MV connection with M1 cassette MV connection with M2 cassette

LV connection
With the withdrawable circuit breaker, LV wiring uses an LV connector with:
b the moving part (male Harting socket) at the end of a flexible cable, entirely
connected to the control mechanism terminal via a bellow
b the fixed part (female Harting socket) compatible with the male part mounted
on the top inside part of the cassette.
Interlocking function
In conformity with standard IEC 62271-200, an interlocking function prohibits:
b racking-in when the LV connector is not connected
b disconnection of the LV connector if the circuit breaker is in the racked-in position.
PE50197

LV plug connection

40
 SF F400 circuit breakers Description of functions
withdrawable version GMH stored energy operating mechanism
Wiring diagram

Operation of the electrical GMH stored energy mechanism

028368

This gives the device an opening and closing speed that is independent of the
operator whether the order is electrical or manual.
The electrical control mechanism carries out reclosing cycles and is automatically
recharged by a geared motor each time after closing.
It consists of:
b the stored energy operating mechanism which stores in springs the energy
required to open and close the device
b a manual lever arming device for the springs
b an electrical arming device with a motor to automatically rearm the control
mechanism as soon as the circuit breaker is closed (optional)
b manual push-button controls on the front face of the circuit breaker (red and black)
b an electrical remote-closing device comprising a release and an anti-pumping relay.
b an electrical opening device comprising one or several releases of the following
type:
v shunt opening
v undervoltage
v Mitop, low energy release only used Sepam 100 LA protection relays
b an operation counter
b an open/closed position indicator with a mechanical indicator (black and white)
b an armed control mechanism status indicator with a mechanical indicator
and an electrical contact (optional)
b a block of 14 auxiliary contacts, available according to the wiring layout used
b a pressure switch contact activated by a drop in gas pressure (optional: single
or double threshold pressure switch)

Wiring diagram (principle)

DE57420EN

Close CB

Open CB

M3

YF + Mitop
anti-pumping YO1 YO2 YM

Motor Shunt closing Control Shunt Under- Low energy Changeover NO NC Pressostat
release mechanism opening voltage release contact contacts contacts
+ anti-pumping armed release release (Mitop)
system indicator contact

Remote control

41
 SF F400 circuit breakers Description of functions
withdrawable version Opening circuit

Composition
DE57421EN

The opening circuit can be produced using the following components:

b a shunt opening release (on energizing) (YO1)
b a second shunt opening release (on energizing) (YO2)
b undervoltage release (YM)
(1) b low energy release (Mitop).
Note: see the table of the releases combinations page Order form .

Shunt opening release (YO1 and YO2)

Energizing this unit causes instant opening of the circuit breaker.
(1) or (2) Characteristics
or (3) Power supply See Order form page
Threshold V AC 0.85 to 1.1 Ur
V DC 0.7 to 1.1 Ur
Consumption V AC 160 VA
Operating mechanism V DC 50 W
DE58092

Undervoltage release (YM)

This release unit causes the systematic opening of the circuit breaker when its
supply voltage drops below a value less than 35% of the rated voltage, even if this
drop is slow and gradual. It can open the circuit breaker between 35% and 70% of
its rated voltage. If the release unit is not supplied power, manual or electrical closing
Shunt opening release (1) of the circuit breaker is impossible. Closing of the circuit breaker is compulsory when
the supply voltage of the release unit reaches 85% of its rated voltage.
DE57390

Characteristics
Power supply See Order form page
Threshold Opening 0.35 to 0.7 Ur
Closing 0.85 Ur
Consumption Triggering V AC 400 VA
V DC 100 W
Undervoltage release (2) Latched V AC 100 VA
V DC 10 W
DE57391

Low energy release (Mitop)

This specific release unit comprises a low consumption unit and is specifically used
for Sepam 100LA self-powered relays.
Characteristics
Power supply Direct current
Low energy release (3)
Threshold 0.6 A < I < 3 A
Any tripping due to the Mitop release unit is momentarily indicated by an SDE type
changeover contact (option).

42
 SF F400 circuit breakers Description of functions
withdrawable version Remote control

Function
DE57422

Remote control enables the remote opening and closing of the circuit breaker.

Composition
The remote control mechanism comprises:
b an electrical motor with gearing
b a shunt closing release (YF) combined with an anti-pumping device
b an operation counter.

Electrical motor (M)

The electrical motor carries out the automatic rearming of the stored energy unit as
soon as the circuit breaker is closed. This allows the instant reclosing of the device
after opening. The arming lever is only used as a backup operating mechanism
in the case of the absence of the auxiliary power supply.
The M3 contact indicates the end of arming operations.
Characteristics
Operating mechanism
Power supply See Order form page
Threshold V AC/V DC 0.85 to 1.1 Ur
DE57392

Consumption V AC 380 VA
V DC 380 W

Electrical motor (4) Shunt closing release (YF)

This release allows the remote closing of the circuit breaker when the operating
mechanism is armed.
DE58092

Characteristics
Power supply See Order form page
Threshold V AC 0.85 to 1.1 Ur
V DC 0.85 to 1.1 Ur
Consumption V AC 160 VA
Shunt closing release (5)
V DC 50 W
The shunt closing release is combined with an anti-pumping relay that enables priority
DE57393

to be given to opening in the case of a permanent closing order. This thus avoids
the device being caught in an uncontrolled opening-closing cycle.

Operation counter (6)

Operation counter
The operation counter is visible on the front panel.
It displays the number of switching cycles (CO) that the device has carried out.

43
 SF F400 circuit breakers Description of functions
withdrawable version Indication and locking/interlocking

Open/closed auxiliary contacts

DE57423

The number of contacts available depends on the options chosen on the operating
mechanism.
In the basic configuration, the circuit breakers operating mechanism comprises
a total of:
b 5 normally closed contacts (NC)
b 5 normally open contacts (NO)
b 1 changeover contact (CHG).
The usage procedure for auxiliary contacts is given in the following table:
Options
NC contact NO contact
Shunt opening release (each one) 0 1
Undervoltage release 0 0
Low energy release (Mitop) 0 0
In order to know the final number of available contacts, you must deduct the total
number of contacts included in the circuit breaker (5 NC + 5 NO + 1 CHG),
the number of contacts used given in the table above.
Operating mechanism E.g.: a circuit breaker equipped with a remote control and a shunt trip unit has
the following available contacts:
5 NC + 4 NO + 1 CHG.
DE57394

With a undervoltage release instead of the shunt trip, this circuit breaker would have
the following available contacts:
5 NC + 5 NO + 1 CHG.
Shunt opening release combination
Auxiliary contacts (7) 1st release Shunt opening Undervoltage release Mitop
release YO1 YM
2nd release
DE57395

Without 5NC + 4NO + 1CHG 5NC + 5NO+ 1CHG

Shunt opening release 5NC + 3NO + 1CHG 5NC + 4NO+ 1CHG 5NC + 4NO + 1CHG
YO2
Undervoltage release 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG
YM
Mitop 5NC + 4NO + 1CHG 5NC + 5NO + 1CHG
Keylocking kit (8)

Locking the circuit breaker in the open position

This key-operated device allows the circuit breaker to be locked in the open position.
The circuit breaker is locked in the open position by blocking the opening push button
in the engaged position.
Locking is achieved using a Profalux or Ronis captive key type keylock.

44
SF F400 circuit breakers Description of functions
withdrawable version Safety functions

This table describes the safety functions available on the SF circuit breaker
withdrawable version.
How to use the table
Each of the boxes describes the functional status of each circuit breaker position
and the associated parts:
Possible status
Possible status, impossible operation
Impossible status

Parts Circuit breaker positions

Insertion Racking-in

Extraction Racking-out
Removed Disconnected Test position Service
1 - Cassette Fool-proof
protection (1)

No opening shutters

Shutters padlocking possible

2 - LV plug Disconnected No door closing

Connected No unplugging (4)

3 - Circuit breaker Closed No racking-in No racking-out

Auto-discharge
function (2)
Open No closing

Open position circuit breaker locking available (2)

4 - Switchboard door Open No racking-in

Closed No door opening (3)

(1) This protection mechanism ensures that the performance levels of the circuit breaker correspond with those of the cassette..
(2) Option.
(3) Interlocking device to be fitted to the cubicle door.
(4) Because the door is closed.

45
SF F400 circuit breakers Dimensions
withdrawable version

Basic withdrawable unit

SF F400/M1
Dimensions and weights

DE57431

DE57432
1250 A 2500/3150 A
Dimensions (mm) A 738 752
B 540 533
C 2030 2030
D 36 40
Weight (kg) 750 850

DE57433

SF F400/M2
Dimensions and weights
DE57442
DE57441

1250 A 2500/3150 A
Dimensions (mm) A 1278 1285
C 2030 2030
D 36 40
Weight (kg) 750 850
DE57433

46
 SF F400 circuit breakers Dimensions (cont.)
withdrawable version

Connection
SF F400/M1
1250 A 2500/3150 A
DE57437

DE57438

SF F400/M2
1250 A 2500/3150 A
DE57443

DE57444

47
SF F400 circuit breakers Order form
withdrawable version SF F400 withdrawable up to 40.5 kV

Only one of the boxes (ticked X or filled by Basic withdrawable circuit breaker Quantity
the needed value) have to be considered between each
Rated voltage Ur (kV)
horizontal line.
Green box X corresponds to none priced functions. Impulse voltage Up (kVbil)

Short-circuit current Isc (kA)

Rated current Ir (A)

Frequency 50 Hz 60 Hz
Colour for push buttons and indicators
Push buttons open/close: Red/black
Indicator open/close: Black/white
Operating mechanism charged/discharged: White/yellow

Circuit breaker options

1st opening release (see possible choices in combination table below)
Shunt opening release YO1
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

2nd opening release (see possible choices in combination table below)

Shunt opening release YO2
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Undervoltage release YM
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)
Mitop (not available with sismic version)
Without contact With contact

Remote control
Electrical motor M 2432 Vdc 110127 Vdc/ac
4860 Vdc/ac 220250 Vdc/ac
Shunt closing release YF
24 Vdc 60 Vdc 220 Vdc 220 Vac (50 Hz)
30 Vdc 110 Vdc 48 Vac (50 Hz) 120 Vac (60 Hz)
48 Vdc 125 Vdc 110 Vac (50 Hz) 240 Vac (60 Hz)

Locking C.B. in open position Ronis Profalux

Leaflets language French English

M1/M2 cassettes
MC cassette type M1 M2
Rated short-circuit current Isc y 40 kA
Rated current Ir 1250 A 2500/3150 A

M1/M2 cassettes accessories

Racked-in/out position contact 4 NO, 4 NC
Extra handle Quantity
VPIS kit

Releases combinations table

Shunt opening releases YO1/YO2 1 2 1 1 2
Undervoltage release YM 1 1 1 1
Mitop 1 1

48
 ART.95993 Schneider Electric Industries SAS - All rights reserved

Schneider Electric Industries SAS As standards, specifications and designs change from time to time, please ask for confirmation
89, boulevard Franklin Roosevelt of the information given in this publication.
F-92506 Rueil-Malmaison Cedex
Tel: +33 (0)1 41 29 85 00 This document has been printed
www.schneider-electric.com on ecological paper

Publishing: Schneider Electric Industries SAS

Design: Schneider Electric Industries SAS
Printing: Imprimerie du Pont de Claix/JPF - Made in France

AMTED304010EN 01-2008