Piston Pump Metaris

VARIABLE DISPLACEMENT PUMP MA10VO/VSO, SERIES 31
Features
Axial piston pump MA10VO in swashplate
design is used in open loop circuits.
Flow is proportional to drive speed and
displacement. By adjusting the position of
the swashplate it is possible to smoothly
vary the output flow of the pump.
– Port connections to SAE or metric – Long service life
– 2 case drain ports – Short control times
– Operating pressure 4000PSI (280 bar) – Axial and radial loading of drive shaft
possible
– Good suction characteristics
– Wide range of controls
– Low noise level
– Through drive option for multi-circuit system
– High power/weight ratio
– SAE & ISO mounting flanges available
2
Technical Data
1. Input Operating Pressure Range
Absolute pressure at port S (A)
Pabs min .................. 11.6 PSI or (0.8 Bar)
Pabs max ................. 435 PSI or (30 Bar)
2. Output Operating Pressure Range

Pressure at port B
Nominal pressure ........... PN 4000 PSI or (280 Bar)
Peak pressure ................ Pmax 5070 PSI or (350 Bar)
3. Case Drain Pressure

The maximum pump case drain pressure measured at ports L, L1 is 7 PSI (0.5 Bar) higher than
the input pressure at ports S, but not exceeding more than 30 PSI (2 Bar) absolute.
4. Direction of Flow
(“S” inlet port to “B” pressure port)
5. Table of values (theoretical values, without considering ηmh and ηv; values rounded)
Size 18 28 45 71 100 140
Displacement Vgmax cm 3
18 28 45 71 100 140
Max. Speed at Vgmax nomax rpm 3000 3000 2600 2200 2000 1800
Max. flow at nomax Qomax L/min 59.4 84 117 156 200 252
Max. power ∆p = 4000 psi
at nomax Pomax kW 27.7 39 55 73 93 118
(∆p = 280 bar)
Max. torque ∆p = 4000 psi

at Vgmax Tmax Nm 58.3 125 200 316 445 623
(∆p = 280 bar)
Weight (without fluid) m kg 26.5 15 21 33 45 60

Notes: Values shown are valid for an absolute pressure of 1 bar at suction port. If the flow is reduced or if the inlet pressure is increased
the speed may be increased.
Hydraulic Formula
6. Determination of Size Vg = geometric displacement cu.in. or [cm3]
Imperial Metric per rev.
Vg ● n ● ηv Vg ● n ● η v
Flow Q= gpm L/min ∆p = differential pressure PSI or (Bar)
231 1000
n = speed [rpm]
Vg ● ∆p Vg ● ∆p
Torque T= lb-ft Nm ηv = volumetric efficiency
24 ● ● ηmh 20 ● ● ηmh
ηmh = mechanical-hydraulic efficiency
Q ● ∆p Q ● ∆p ηt = total efficiency (ηt = ηv ● ηmh)
Power P= HP kW
1714 ● ηt 600 ● ηt
Q = Flow (gpm) or (L/min.)
3
Performance Information
Flow Q.
Power @ Q max. Power @ Q min.
Flow Q.
Power @ Q max.
Power @ Q min.
Flow Q.
Power @ Q max.
Power @ Q min.
4
Performance Information - cont’d
Flow Q.
Power @ Q max.
Power @ Q min.
Flow Q.
Power @ Q max.
Power @ Q min.
5
Performance Information - cont’d
140 Series at 1800 rpm
Size 140
_________
n = 1800 rpm
Total efficiency:
Imperial Metric
Q●P Q●P
ηt =
PQ max ● 1714 PQ max ● 600
Volumetric efficiency:
Q
ηv =
Qtheor.
6
Ordering Code
MA10V 0 71 DR 31 R P S
Axial piston unit
Swash plate variable pump MA10V
Swash plate variable pump, for industrial MA10VS
Modes of operation
Pump, open circuit O
Size
Displacement Vgmax (cm³) 18 28 45 71 100 140

Control devices
Pressure control DR
     
G - Remote control DRG
Pressure and flow control, DFR

     
X channel plugged DFR1
Pressure flow and power
–     – DFLR
control
Series
Series 31
Direction of rotation
clockwise R
Viewed on drive shaft
counter-clockwise L
Seals
Buna-N (NBR per DIN ISO 1629) ; P
FPM (fluorocarbon) V
Shaft end 18 28 45 71 100 140

SAE-splined shaft 3/4” 7/8” 1” 1 1/4” 1 1/2” 1 3/4” S
SAE-splined shaft, reinforced (higher thru drive torques) 3/4” 7/8” 1” 1 1/4” * * R
SAE-splined shaft, smaller size (not for pumps with thru drive) 5/8” * 7/8” * 1 1/4” * U
SAE-splined shaft, reinforced U-type shaft * * 7/8” * 1 1/4” * W
SAE-keyed shaft 3/4” 7/8” 1” 1 1/4” 1 1/2” 1 3/4” K
parallel with key DIN 6885 18mm 22mm 25mm 32mm 40mm 45mm P
7
Ordering Code
C 62 N00
Thru-drive 18 28 45 71 100 140

Without through drive       N00
Thru-drive pumps are only fitted with side ports
Mounting flange Shaft/coupling SAE BB A10V45 –      K04
82-2 (SAE A) 16-4 (SAE A) G2, GC2/GC3-1X –      K01
101-2 (SAE B) 22-4 (SAE B) A10VO28 (shaft S), G3 –      K02
101-2 (SAE B) 22-4 (SAE B) A10VO28 (shaft S), G4 –     – K68
127-2 (SAE C) 32-4 (SAE C) A10VO71 (shaft S) – – –    K07
152-4 (SAE D) 44-4 (SAE D) A10VO140 (S.E. S) – – – – –  K17
For unlisted coupling sizes please contact Metaris
Service ports
(Pressure port B and Suction port S) 18 28 45 71 100 140

(Rear ports, UNC Mounting screws)       61
(Opposite side ports, UNC mounting screws)       62 Port pos.
(Rear ports, metric mounting screws) –      11 61, 11, 91
and 41
(Opposite side ports, metric mounting screws)       12 only for
(Rear ports, UNC Mounting screws) – – –  – – 91 version
without
(Opposite side ports, UNC mounting screws) – – –  – – 92 through
(Rear ports, metric mounting screws) – – –  – – 41 drive
(Opposite side ports, metric mounting screws) – – –  – – 42
Mounting flange 18 28 45 71 100 140

SAE 2 hole 3.250” 4” 4” 5” 5” * C
ISO 2 hole 80mm 100mm 100mm 125mm 125mm 180mm A
SAE 4 hole * * * * * 6” D
 = available
Multiple Pumps
1. If a second Metaris hydraulic pump is to be factory-mounted, then both ordering codes are to be
specified, combined with a “+”. Ordering code 1st pump + Ordering code 2nd pump. Ordering
example: MA10VO71DR/31R-PSC62K02 + MA10VO28DR/31R-PSC62N00
2. If a gear pump is to be factory-mounted please contact Metaris support staff.
8
Fluid
1. Hydraulic Fluid
The MA10V open loop pump in the standard design should be used with a good quality, petroleum
based anti-wear hydraulic fluid.
2. Operating Viscosity Range

In order to obtain optimum efficiency we recommend that the operating viscosity be selected from
within the range.
At operating temperature
Optimum viscosity (opt) __80...170 SUS (16 / 36 mm2/s)
Limits of viscosity range

The following values are valid for extreme operating conditions:
min = 60 SUS (10 mm2/s)

for short periods at max. leakage oil temperature of 93° C
max = 4600SUS (1000 mm2/s)

1400 SUS (300 mm2/s) on short term cold start
3. Temperature Range
tmin = -15°C; tmax = +80°C.; tmin = -5°F; tmax = +175°F
Filtration
In order to ensure reliable operation of the axial piston unit, the operating fluid must be maintained
to a cleanliness class of 18/14 to ISO4406 or NAS 1638 class 9. As a guide the fluid cleanliness level
may be achieved using a 10 micron filter.
Installation Information
The pump housing must be filled with clean hydraulic fluid prior to pump start up and remain full.
The concentricity between the prime mover drive shaft and the pump shaft 0.05mm.
Prime mover drive shaft Pump shaft
.05mm
9
Installation Information - cont’d.

The installation position of the pump is optional.
The pump housing must be filled with fluid both when commissioning and in
operation. In order to achieve low noise levels, all connecting lines (inlet, case
drain) should be isolated from the tank by flexible lines.
1. Vertical installation the following conditions should be noted:

- Before installing the pump inside a tank fill the pump case with
- fluid
- Make sure the ports are below the oil level (L), (L1) & S
- Avoid mounting above the tank whenever possible in order to maintain a
low noise level
- The permissible inlet height is a result of the overall pressure loss “A” may
not be greater than 32 inches (800 mm)
2. Horizontal Installation
- The pumps must be install so (L) or (L1) the case drain is at the top of the
pump
- If the minimum fluid level is below the ports of the pump, pipe the ports L
or L1 & S below the minimum oil level.
low noise level.
- The permissible inlet height (h) is a result of the overall pressure loss, “A”
may not be greater then 32 inches (800 mm).
Below the tank position

- Pipe “L”, “L1” and “S” must be mounted below the oil level
10
DR Pressure Control
The pressure control serves to maintain a
constant pressure in the hydraulic system,
within the control range of the pump. The
pump therefore supplies only the amount
of hydraulic fluid required by the actuators.
Pressure may be smoothly set at the control
valve.
Ports
B Pressure Port
S Suction port
L, L1 Case drain ports (L1 sealed)
Response time
t t t
Dynamic response curve sa(ms) sa (ms) sa (ms)
The operating curves values taken under the Size
following conditions 725 psi / 50 bar 3200 psi / 220 bar 4000 psi / 280 bar
28 60 30 20
Operating Conditions; n = 1500 rpm 45 80 40 20
Oil temperature 120 F / 50C 71 100 50 25
Pressure cut-off 5100 psi / 350bar 100 125 90 30
140 130 110 30
Load values were taken by closing the
pressure line with a load valve .
Control Data
Hysteresis and repetition accuracy p ………………. Max. 3 bar
Max. Pressure Increase
Size 18 28 45 71 100 140
ΔP BAR 4 4 6 8 10 12
Pilot oil consumption …………………..max. approx. 3 L/min
11
Unit dimensions DR
Service ports at rear; Models 61N00 and 11N00
Size 18 to 140
counter clockwise
Unit dimensions DR
Service ports at side; Models 62N00 and 12N00
Size 18 to 140
counter clockwise
Size A1 A2 A3 A4 A5 Metric Adapter L & L1 X

18 * * 121 126 167 M16 X 1.5 7/16-20UNF-2B
28 74 36 121 136 179 M18 X 1.5 7/16-20UNF-2B
45 81 36 121 146 189 M22 X 1.5 7/16-20UNF-2B
71 92 36 121 160 215 M22 X 1.5 7/16-20UNF-2B
100 98 36 121 158 285 M27 X 2 7/16-20UNF-2B
140 * * 120 209 292 M27 X 2 9/6-18UNF-2B
12
DRG Pressure Control, Remote Control

Size 18 to 100
Function and design as for DR
A pressure relief valve may be externally piped to port X for
remote control purposes. It is not, however, included with
the DRG control.
The differential pressure at the pilot valve is set as standard

to 20 bar and this results in a pilot flow of 1,5 L/min. If
another setting is required (in the range 10-22 bar), please
state this in clear text.
The remote pilot valve should be mounted no more then

78in (2 meters) from the pump.
Static charateristic
(at n1=1500 rpm; oil temp. =125˚F / 51˚C
Ports
B Pressure Port
S Suction port
X Pilot pressure port
DRG 140
Control Data
Hysteresis and repetittion accuracy p ………Max. 3 bar
Size 18 28 45 71 100 140

ΔP BAR 4 4 6 8 10 12
Pilot oil consumption …………….max. approx. 4.5 L/min
13
DFR/DFR1 Pressure/Flow Control
In addition to the pressure control

function,the pump flow may be varied by
means of a differential pressure at the
actuator (e.g. an orifice).
In model DFR1 the X orifice is plugged.
Ports
B Pressure Port
S Suction port
14
DFR/DFR1 Pressure/Flow Control - cont’d
Flow Control/Differential
Pressure p:
Adjustable between 10 and 22 bar (higher values
on request). Standard setting: 14 bar. If a different
setting is required, please state in clear text.
When port X is unloaded to tank, a zero

stroke pressure of
p = 18 ± 2 bar (“stand by”) results.
Control Data
For pressure control technical data see DR Pressure control
Max. flow deviation (hysteresis and increase) measured at drive speed n = 1450 rpm
Size 18 28 45 71 100 140

ΔQmax L/min 0.5 1 1.8 2.8 4.0 6.0
Pilot oil consumption DFR …….. max. approx. 3-4.5 L/min

Pilot oil consumption DFR1 …... max. approx. 3 L/min
15
Unit dimensions DFR / DFR1 / DRG

Size 28 to 140
counter clockwise
L
L1
Unit dimensions DFR / DFR1 / DRG

Service ports on sides; Models 62N00 and 12N00
Size 18 to 140
L counter clockwise
L1
Size A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 X

18 * 36 * * * * 167 121 41 112 126 7/16-20UNF-2B
28 74 36 121 40 211 228 179 121 41 116 135 7/16-20UNF-2B
45 81 36 121 40 231 248 189 118 40 122 140 7/16-20UNF-2B
71 92 36 121 40 264 281 215 119 40 145 163 7/16-20UNF-2B
100 98 36 121 40 328 346 286 119 40 145 164 7/16-20UNF-2B
140 * 50 * * * * 292 120 26 186 210 9/16 - 18 UNF-2B
16
DFLR Pressure/Flow/Power Control
In order to achieve a constant drive torque

with a varying operating pressure, the swivel Not included
angle and with it the output flow from the
axial piston unit is varied so that the product
of flow and pressure remain constant.
Flow control is possible below the limit of the

power curve.
Ports
B Pressure Port
S Suction port
The power characteristic is factory-set, so please enter details in clear text, e.g. 20 kW at 1450 rpm.
There are four spring arrangements used for the power valve set-up refer to the chart below.
Spring group A ..... to 1300 psi/90 bar

Spring group B ..... to 2320 psi/160 bar
Spring group C ..... to 3480 psi/240 bar
Spring group D ..... over 3480 psi/240 bar
Control data
For pressure control technical data see DR Pressure control.
For flow control technical data see DFR control.
Start of control …………………………… from 80 bar
Pilot oil consumption …………………….. max. approx. 5.5 L/min
17
Unit dimensions DFLR

Size 28 to 100
counter clockwise
Unit dimensions DFR / DFR1 / DRG / DFLR

Size 18 to 100
counter clockwise
Size A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 X

18 * * * * * * 40 121 130 36 121 40 109 126 7/16-20UNF-2B
28 102 88 57 109 48 228 40 121 143 36 121 40 116 135 7/16-20UNF-2B
45 109 90 57 111 54 248 40 121 153 36 118 40 122 140 7/16-20UNF-2B
71 120 103 57 124 70 281 40 121 180 36 119 40 145 163 7/16-20UNF-2B
100 126 112 57 133 112 345 40 121 249 36 119 40 146 164 7/16-20UNF-2B
140 * * * * * * * * * * * * * * *
18
Mounting Dimension, Sizes 28
Service ports at rear: no through drive

Models 61N00 and 11N00
19
Service ports on side;

no through drive, Models 62N00 and 12N00
model 12, 4- M10 x 1.5 - 6H

model 12, 4- M10 x 1.5 - 6H
20
Service ports at rear;

13
21
Service ports on side;

Without considering adjustments
22
Service ports on sides:

23
Service ports at rear;

MA10 Piston pump with MV10 Vane pump fitted
24
Service ports on sides;

25

Service ports on rear; Models 61N00 and 11N00
26
VARIABLE DISPLACEMENT PUMP MA10VO, SERIES 31
Permissible Bending
Size 28 45 71 100 140

Permissible bending Tm lb-ft 65 101 159 221 332
moment
Nm 88 137 216 300 450
Weight m1 lbs 33 46 73 99 132
kg 15 21 33 45 60
Distance to center l1 in 4.33 5.11 5,91 6.30 6.30
of gravity mm 110 130 150 160 160
Through Drive
Axial piston unit MA10VO can be supplied with a through drive, as shown in the ordering code on page 7 & 8.
The type of through drive is determined by codes (K01-K17). If the combination pump is not mounted in the
factory, the simple type code is sufficient.
Included with the pump are: Coupling sleeve, seals and necessary hardware.
Combination pumps
By mounting combination pumps circuits independent of each other are available for use.
1. If the combination pump consists of 2 MA10VO pumps and if these are to be delivered ready assembled,
then the two type codes are to be combined with a “+”.
Ordering example: MA10VO71DR/31R-PSC62K02 + MA10VO28DR/31R-PSC62N00
2. If a gear pump, vane or other type pump is to be mounted in the factory as a second or third pump, please
consult the factory for available mounting information.
27
Unit Dimensions of Combination Pumps
M1
M2
M3
M4
Pump 1 MA10VO28 MA10VO45 MA10VO71 MA10VO100 MA10VO140

M1 M2 M3 M4 M1 M2 M3 M4 M1 M2 M3 M4 M1 M2 M3 M4 M1 M2 M3 M4
Pump 2
in. 6.5 8.03 13.74 15.71 7.24 9.02 14.72 16.69 8.54 10.51 16.21 18.19 10.83 13.31 19.02 20.98 10.83 13.78 19.49 21.46
MA10VO18
mm 165 204 349 399 184 229 373 424 217 267 412 462 275 338 483 533 275 350 495 545
in. 6.5 8.03 14.53 15.67 7.24 9.02 15.51 16.65 8.54 10.51 17.01 18.15 10.83 13.31 19.8 20.94 10.83 13.78 20.28 21.42
MA10VO28
mm 165 204 369 398 184 229 3.94 423 217 267 432 461 275 338 503 532 275 350 515 544
in. 7.24 9.02 16.3 17.64 8.54 10.51 17.76 19.36 10.83 13.31 20.55 21.93 10.83 13.78 21.02 22.4
MA10VO45
mm 184 229 413 448 217 267 451 486 275 338 522 557 275 350 534 569
in. 8.54 10.51 19.06 20.63 10.83 13.31 21.85 23.43 10.83 13.78 22.32 23.9
MA10VO71
mm 217 267 484 524 275 338 555 585 275 350 567 607
in. 10.83 14.02 24.84 26.5 10.83 14.49 24.31 29.97

MA10VO100
mm 275 356 631 673 275 368 643 685
in. 10.83 14.49 25.31 29.97

MA10VO140
mm 275 368 643 685
28
Dimensions of Through Drive Covers:

Mounting Flange for SAE A 2-holes 3.250 (82.55) pilot
Ordering code with 5/8” 9T spline coupling K01
Ordering code with 3/4” 11T spline coupling K52
SIZE (1) (2) (3)

28 204mm 47mm M10-16mm deep
100 338mm 65mm M10-20mm deep
140 350mm 77mm M10-20mm deep
Mounting Flange for SAE B 2-hole 4” (101.6) pilot

Ordering code with 7/8” 13T spline coupling K 02 & K 68
Ordering code with 1” 15T spline coupling K 04
Ordering code 7/8” keyed coupling K 03
Ordering code 1” keyed coupline K 05
SIZE (1) (2) (3)

100 338mm 65mm M12-20mm deep
140 350mm 77mm M12-20mm deep
29
Mounting flange for SAE 2 hole 5” (127) pilot

Ordering code with 1 1/4” 14T spline coupling K07
Ordering code with 1 1/4” Keyed coupling K08
SIZE (1) (2) (3) (4) (5)

71 177mm 90mm 18mm 52mm M16-18mm deep
Mounting flange for SAE D 4 hole MA10V140

Ordering code K17
30
Features
Axial piston pump MA10VO in swashplate design
is used in open loop circuits. Flow is proportional
to drive speed and displacement. By adjusting the
position of the swashplate it is possible to smoothly
vary the output flow of the pump.
– Port connections to SAE or metric – High power/weight ratio Long service life
– 2 case drain ports – Short control times
– Operating pressure 3625 psi (250 bar) – Axial and radial loading of drive shaft
possible
– Good suction characteristics
– Wide range of controls
– Low noise level
– Through drive available
– SAE & ISO mounting flanges available
31
Technical Data
1. Input Operating Pressure Range
Absolute pressure at port S (A)
Pabs min .................. 11.6 PSI or (0.8 Bar)
Pabs max ................. 435 PSI or (30 Bar)
2. Output Operating Pressure Range

Pressure at port B
Nominal pressure ........... PN 3625 PSI or (250 Bar)
Peak pressure ................ Pmax 4500 PSI or (315 Bar)
3. Case Drain Pressure

The maximum pump case drain pressure measured at ports L, L1 is 7 PSI (0.5 Bar) higher than
the input pressure at ports S, but not exceeding more than 30 PSI (2 Bar) absolute.
4. Direction of Flow
(“S” inlet port to “B” pressure port)
5. Table of values (theoretical values, without considering ηmh and ηv; values rounded)
Size 45 60
Displacement Vgmax cm 3
45 60
Max. Speed at Vgmax nomax rmp 2600 2700
Max. flow at nomax Qomax L/min 117 162
Max. power at nomax Pomax kW 49 68
Max. torque at Vgmax Tmax Nm 179 238
Weight (without fluid) m kg 18 22

Notes: Values shown are valid for an absolute pressure of 1 bar at suction port. If the flow is reduced or if the inlet pressure is increased
the speed may be increased.
Hydraulic Formula
1. Determination of Size Vg = geometric displacement cu.in. or [cm3]
Imperial Metric per rev.
Vg ● n ● ηv Vg ● n ● η v
Flow Q= gpm L/min ∆p = differential pressure PSI or (Bar)
231 1000
n = speed [rpm]
Vg ● ∆p Vg ● ∆p
Torque T= lb-ft Nm ηv = volumetric efficiency
24 ● ● ηmh 20 ● ● ηmh
ηmh = mechanical-hydraulic efficiency
Q ● ∆p Q ● ∆p ηt = total efficiency (ηt = ηv ● ηmh)
Power P= HP kW
1714 ● ηt 600 ● ηt
Q = Flow (gpm) or (L/min.)
32
Ordering Code
MA10VS 0 45 DFR 52 R P S
Axial piston unit
Swash plate variable pump MA10VS
Modes of operation
Pump, open circuit 
Size
Displacement Vgmax (cm³) 45 60
Control devices
Pressure control DR
 
G - Remote control DRG
Pressure and flow control, DFR

 
X channel plugged DFR1
Series
Series
52
Consult the factory for other series 50/53
Direction of rotation
clockwise R
Viewed on drive shaft
counter-clockwise L
Seals
Buna-N (NBR per DIN ISO 1629) ; P
FPM (fluorocarbon) V
Shaft end 45 60
SAE-splined shaft   S
SAE-splined shaft, smaller size (not for pumps with thru drive)   U
SAE-splined shaft, reinforced U-type shaft – – W
SAE-keyed shaft   K
parallel with key DIN 6885   P
33
Ordering Code
C 62 N00
45 60
Without through drive   N00
Thru-drive pump with side ports only
82-2 SAE A 16-4 SAE A   K01
K02 &
101-2 SAE B 22-4 SAE B  
K04
Service ports
(Pressure port B and Suction port S) 45 60
(Rear ports, UNC Mounting screws)   61

Port pos.
(Opposite side ports, UNC mounting screws)   62 61, 11
only for
(Rear ports, metric mounting screws)   11 version
without
through
(Opposite side ports, metric mounting screws) – – 12
drive
(SAE-theaded rear)  – 64
Mounting flange 45 60
SAE 2 Bolt hole   C
SAE 4 Bolt hole –  D
 = available
34
Fluid
1. Hydraulic Fluid
The MA10V open loop pump in the standard design should be used with a good quality, petroleum
based anti-wear hydraulic fluid.
2. Operating Viscosity Range

In order to obtain optimum efficiency we recommend that the operating viscosity by selected from
within the range.
At operating temperature
Optimum viscosity (opt) __80...170 SUS (16 / 36 mm2/s)
Limits of viscosity range

The following values are valid for extreme operating conditions:
min = 60 SUS (10 mm2/s)

for short periods at max. leakage oil temperature of 93° C
max = 4600SUS (1000 mm2/s)

1400 SUS (300 mm2/s) on short term cold start
3. Temperature Range
tmin = -15°C; tmax = +80°C.; tmin
4. Filtration
In order to ensure reliable operation of the axial piston unit, the operating fluid must be maintained
to a cleanliness class of 18/14 to ISO4406 or NAS 1638 class 9. As a guide the fluid cleanliness level
may be achieved using a 10 micron filter.
The pump housing must be filled with clean hydraulic fluid prior to pump start up and remain full.
The concentricity between the prime mover drive shaft and the pump shaft 0.05mm.
Prime mover drive shaft Pump shaft
.05mm
35
Installation Information - cont’d.

The installation position of the pump is optional.
The pump housing must be filled with fluid both when commissioning and in
operation. In order to achieve low noise levels, all connecting lines (inlet, case
drain) should be isolated from the tank by flexible lines.
1. Vertical installation the following conditions should be noted:

- Before installing the pump inside a tank fill the pump case with
- fluid
- Make sure the ports are below the oil level (L), (L1) & S
low noise level
- The permissible inlet height is a result of the overall pressure loss “A” may
not be greater than 32 inches (800 mm)
2. Horizontal Installation
- The pumps must be install so (L) or (L1) the case drain is at the top of the
pump
- If the minimum fluid level is below the ports of the pump, pipe the ports L
or L1 & S below the minimum oil level.
low noise level.
- The permissible inlet height (h) is a result of the overall pressure loss, “A”
may not be greater then 32 inches (800 mm).
Below the tank position

- Pipe “L”, “L1” and “S” must be mounted below the oil level
36
DR Pressure Control
The pressure control serves to maintain a

constant pressure in the hydraulic system,
within the control range of the pump. The
pump therefore supplies only the amount
of hydraulic fluid required by the actuators.
Pressure may be smoothly set at the pilot
valve.
Ports
B Pressure Port
S Suction port
Control Data
Hysteresis and repetitive accuracy p ………………. Max. 3 bar
Size 45 60
ΔP BAR 6 8
Pilot oil consumption …………………..max. approx. 3 L/min
For other controls DRG and DFR see page 13 & 14
37
Pressure control DR
Version MA10VSO45DR/52R-XXC62/12NOO
38
DFR
Version MA10VSO45 DFR1/52L-XXC64N00
DRG
39
DFR
Version MA10VSO60 DFR1/52L-XXC62/12N00
DRG
X Port
40
DFR
DRG
41
DFR
DRG
42
NOTES
43
PTM022010-Rev2

Piston Pump Metaris

Uploaded by

Copyright:

Available Formats

Piston Pump Metaris

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Piston Pump Metaris

Uploaded by

Copyright:

Available Formats

VARIABLE DISPLACEMENT PUMP MA10VO/VSO, SERIES 31

– Port connections to SAE or metric – Long service life

– 2 case drain ports – Short control times

2. Output Operating Pressure Range

3. Case Drain Pressure

Max. torque ∆p = 4000 psi

Weight (without fluid) m kg 26.5 15 21 33 45 60

Power @ Q max. Power @ Q min.

Performance Information - cont’d

Performance Information - cont’d

140 Series at 1800 rpm

Axial piston unit

Swash plate variable pump MA10V

Swash plate variable pump, for industrial MA10VS

Displacement Vgmax (cm³) 18 28 45 71 100 140

Pressure and flow control, DFR

Buna-N (NBR per DIN ISO 1629) ; P

Shaft end 18 28 45 71 100 140

SAE-splined shaft, reinforced U-type shaft * * 7/8” * 1 1/4” * W

SAE-keyed shaft 3/4” 7/8” 1” 1 1/4” 1 1/2” 1 3/4” K

Thru-drive 18 28 45 71 100 140

(Pressure port B and Suction port S) 18 28 45 71 100 140

(Opposite side ports, metric mounting screws) – – –  – – 42

Mounting flange 18 28 45 71 100 140

2. If a gear pump is to be factory-mounted please contact Metaris support staff.

2. Operating Viscosity Range

Limits of viscosity range

min = 60 SUS (10 mm2/s)

max = 4600SUS (1000 mm2/s)

tmin = -15°C; tmax = +80°C.; tmin = -5°F; tmax = +175°F

Prime mover drive shaft Pump shaft

Installation Information - cont’d.

1. Vertical installation the following conditions should be noted:

Below the tank position

Size A1 A2 A3 A4 A5 Metric Adapter L & L1 X

DRG Pressure Control, Remote Control

The differential pressure at the pilot valve is set as standard

The remote pilot valve should be mounted no more then

Max. Pressure Increase

Size 18 28 45 71 100 140

Pilot oil consumption …………….max. approx. 4.5 L/min

DFR/DFR1 Pressure/Flow Control

In addition to the pressure control

In model DFR1 the X orifice is plugged.

DFR/DFR1 Pressure/Flow Control - cont’d

When port X is unloaded to tank, a zero

p = 18 ± 2 bar (“stand by”) results.

Size 18 28 45 71 100 140

Pilot oil consumption DFR …….. max. approx. 3-4.5 L/min

Unit dimensions DFR / DFR1 / DRG

Unit dimensions DFR / DFR1 / DRG

Size A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 X

DFLR Pressure/Flow/Power Control

In order to achieve a constant drive torque

Flow control is possible below the limit of the

Spring group A ..... to 1300 psi/90 bar

Unit dimensions DFLR

Unit dimensions DFR / DFR1 / DRG / DFLR

Size A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 X

Mounting Dimension, Sizes 28