Compact Adjustable Busbar Support (Cabs) Imperial
Compact Adjustable Busbar Support (Cabs) Imperial
Compact Adjustable Busbar Support (Cabs) Imperial
CONTENT
1. WHAT IS A SHORT-CIRCUIT? 03
2. RECOMMENDATIONS OF SUPPORT 06
SPACING TABLES
3. ALUMINUM PROFILE 07
CONFIGURATION ASSEMBLY
5. APPENDIX A: RECOMMENDATIONS 09
OF SUPPORT SPACING TABLES
SPACING RECOMMENDATIONS FOR 10
1/4 INCHES BARS,
2 SLOT INSULATORS
SPACING RECOMMENDATIONS FOR 17
1/4 INCHES BARS,
3 SLOT INSULATORS
SPACING RECOMMENDATIONS FOR 27
1/4 INCHES BARS,
4 SLOT INSULATORS
SPACING RECOMMENDATIONS FOR 40
3/8 INCHES BARS,
2 SLOT INSULATORS
SPACING RECOMMENDATIONS FOR 47
3/8 INCHES BARS,
3 SLOT INSULATORS
SPACING RECOMMENDATIONS FOR 56
3/8 INCHES BARS,
4 SLOT INSULATORS
WHAT IS A SHORT-CIRCUIT?
Short-circuit
The effect of this phenomena is very dangerous, because the creepage and clearance distances can
be dramatically reduced due to movements of non-insulated conductors (mechanical deformation,
oscillations) during the short-circuit.
The result could be a flash over between two conductive parts.
The value of peak current is obtained by multiplying the r.m.s. value of the short-circuit current
by the factor n.
Conclusion:
Compact Adjustable Busbar Support (CABS) Imperial - Using standard calculations, the Compact
Adjustable Busbar Support [CABS] Imperial spacing recommendations have been developed based on
mechanical strength tests and calculated electromagnetic short circuit phenomena [mechanical effects,
vibration, etc.
2) Using the selected table (Appendix A), the desired Short circuit (SCCR rms or Ipk - kA), and
copper bars width, you will find the recommended busbar support distance/spacing between axis
of supports.
1) In the following table, “Weight per Inch” values can be determined by using the dimensions of the copper
busbar in your application.
2) Multiply this “Weight per Inch” value by the quantity of copper bars to be used to generate the “Total Weight
per Inch” for the application.
3) Multiply the “Total Weight per Inch” by the value you found in the “Recommended Spacing Tables”
according to SCCR values. This will give you the total copper weight supported by 1 CABS aluminum
profile.
4) Select the appropriate profile configuration (Single, Double, Stacked) based on the chart titled
“Maximum Allowable Weight on CABS Aluminum Profile.
• Calculation:
1. 5” X 3/8” copper busbar = 0.6029 lbs. per inch
2. 0.6029 X 3 bars X 3 phases = 5.4261 lbs. per inch
3. 5.4261 X 10” (distance between supports) = 54.261 lbs.
4. A 24” long section of the Single profile configuration can safely
support ~280 lbs. Therefore, the Single profile configuration will work for this example.
• Calculation:
1. 5” X 3/8” copper busbar = 0.6029 lbs. per inch
2. 0.6029 X 4 bars X 4 phases = 9.6464 lbs. per inch
3. 9.6464 X 20” (distance between supports) = 192.928 lbs.
4. A 28” long section of the Single profile configuration will safely support ~114 lbs. Therefore, we cannot use
it in this example. We must instead use the Double profile configuration, which can support up to ~327 lbs.
for a 28” span.
RECOMMENDATION OF
SUPPORT SPACING TABLES
COMPACT ADJUSTABLE BUSBAR SUPPORT (CABS) IMPERIAL
SPACING RECOMMENDATIONS FOR 1/4 INCHES BARS (2 SLOT INSULATORS, 1 BAR)
CABS142T / CABS142TN
Phase-Phase Distance
between axis (d): 2.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 28.50 22.17 17.28 15.20 12.68 9.06 7.60 5.55 4.25 - - - -
2.5” X 1/4” 39.37 39.37 32.64 25.39 19.76 17.40 14.49 10.35 8.70 6.38 4.88 - - - -
3” X 1/4” 39.37 39.37 36.65 28.50 22.20 19.53 16.26 11.61 9.76 7.17 5.47 4.06 - - -
3.5” X 1/4” 39.37 39.37 39.37 31.54 24.57 21.61 18.03 12.87 10.79 7.91 5.91 4.25 - - -
4” X 1/4” 39.37 39.37 39.37 34.57 26.93 23.70 19.76 14.09 11.85 8.70 6.18 4.45 - - -
4.5” X 1/4” 39.37 39.37 39.37 37.56 29.29 25.75 21.46 14.88 12.87 9.45 6.50 4.69 - - -
5” X 1/4” 39.37 39.37 39.37 39.37 31.57 27.80 23.15 14.96 13.90 10.20 6.81 4.92 - - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 33.90 29.84 24.84 15.04 14.45 10.94 7.13 5.16 - - -
6” X 1/4” 39.37 39.37 39.37 39.37 36.22 31.85 26.54 15.16 14.49 11.69 7.44 5.39 - - -
Phase-Phase Distance
between axis (d): 3.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 32.24 25.08 19.53 17.20 14.33 10.24 8.58 6.30 4.80 4.09 - - -
2.5” X 1/4” 39.37 39.37 36.61 28.46 22.20 19.53 16.26 11.61 9.76 7.17 5.47 4.65 - - -
3” X 1/4” 39.37 39.37 39.37 31.73 24.72 21.77 18.11 12.95 10.87 7.99 6.10 5.00 - - -
3.5” X 1/4” 39.37 39.37 39.37 34.92 27.20 23.94 19.92 14.25 11.97 8.78 6.69 5.20 - - -
4” X 1/4” 39.37 39.37 39.37 37.99 29.61 26.06 21.69 15.16 13.03 9.57 7.28 5.39 - - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 15.24 14.06 10.31 7.76 5.59 - - -
5” X 1/4” 39.37 39.37 39.37 39.37 34.37 30.24 25.20 15.31 14.65 11.10 8.07 5.83 - - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 36.69 32.28 26.93 15.39 14.69 11.85 8.35 6.02 - - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.06 34.37 28.62 15.47 14.76 12.60 8.66 6.26 4.02 - -
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.67 27.76 21.61 19.02 15.83 11.30 9.49 6.97 5.31 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.38 24.45 21.50 17.91 12.80 10.75 7.87 6.02 5.12 - - -
3” X 1/4” 39.37 39.37 39.37 34.76 27.09 23.86 19.88 14.17 11.93 8.74 6.69 5.67 - - -
3.5” X 1/4” 39.37 39.37 39.37 38.07 29.65 26.10 21.73 15.47 13.03 9.57 7.32 6.18 3.94 - -
4” X 1/4” 39.37 39.37 39.37 39.37 32.17 28.31 23.58 15.55 14.13 10.39 7.91 6.38 4.06 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 34.61 30.47 25.39 15.59 14.84 11.18 8.54 6.57 4.17 - -
5” X 1/4” 39.37 39.37 39.37 39.37 37.01 32.60 27.17 15.67 14.88 11.97 9.13 6.77 4.33 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.69 28.90 16.06 14.96 12.72 9.65 6.97 4.45 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 16.54 15.00 13.50 9.92 7.17 4.57 - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 38.82 30.20 23.54 20.71 17.24 12.32 10.35 7.60 5.79 4.92 3.94 - -
2.5” X 1/4” 39.37 39.37 39.37 34.06 26.54 23.35 19.45 13.90 11.65 8.54 6.54 5.55 4.45 - -
3” X 1/4” 39.37 39.37 39.37 37.64 29.33 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.53 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 16.65 14.06 10.31 7.87 6.69 4.61 - -
4” X 1/4” 39.37 39.37 39.37 39.37 34.57 30.43 25.35 17.01 15.08 11.14 8.54 7.24 4.72 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.64 27.20 17.40 15.12 11.97 9.13 7.56 4.80 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.84 29.02 17.83 15.16 12.76 9.76 7.72 4.92 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.97 30.83 18.27 15.24 13.58 10.35 7.91 5.04 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.60 18.70 15.28 14.21 10.75 8.11 5.20 - -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.48 25.31 22.28 18.54 13.27 11.14 8.15 6.26 5.31 4.25 - -
2.5” X 1/4” 39.37 39.37 39.37 36.57 28.46 25.08 20.87 14.92 12.52 9.17 7.01 5.98 4.76 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.42 27.64 23.03 16.46 13.82 10.16 7.76 6.57 5.20 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.02 8.43 7.17 5.28 - -
4” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.48 27.05 19.33 15.35 11.89 9.09 7.72 5.35 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.76 28.98 20.67 15.39 12.76 9.76 8.27 5.47 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.01 30.83 22.01 15.43 13.58 10.35 8.70 5.55 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.31 15.47 14.33 10.98 8.90 5.67 3.94 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 15.55 14.37 11.57 9.09 5.79 4.02 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 34.65 27.01 23.74 19.80 14.13 11.85 8.70 6.65 5.67 4.53 - -
2.5” X 1/4” 39.37 39.37 39.37 38.94 30.31 26.69 22.24 15.87 13.35 9.80 7.48 6.34 5.08 4.02 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.43 29.41 24.49 17.48 14.69 10.79 8.23 7.01 5.59 4.06 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 36.34 31.97 26.65 19.02 15.59 11.73 8.98 7.60 5.94 4.13 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.09 34.41 28.66 20.47 15.63 12.64 9.65 8.19 6.02 4.17 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 21.89 15.67 13.50 10.31 8.78 6.10 4.25 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 15.83 14.33 10.94 9.33 6.22 4.29 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 16.10 14.49 11.57 9.84 6.34 4.37 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.30 25.91 16.38 14.53 12.20 10.04 6.42 4.45 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
0.1202 in
Short Circuit Current Rating (SCCR), 3 phases
Peak value Ipk (kA) 7.5 17 28 36 46.2 52.5 63 88.2 105 143 187 220 275 330 440
SCCR rms (kA) 5 10 14 18 22 25 30 42 50 65 85 100 125 150 200
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 36.69 28.58 25.16 20.94 14.96 12.56 9.21 7.05 5.98 4.80 3.98 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 32.09 28.23 23.50 16.81 14.09 10.35 7.91 6.73 5.35 4.49 -
3” X 1/4” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.53 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 4.61 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.26 30.24 21.57 17.05 13.31 10.16 8.62 6.69 4.65 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.70 32.24 23.03 17.24 14.21 10.87 9.21 6.77 4.69 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.25 24.45 17.48 14.61 11.54 9.80 6.89 4.76 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.18 25.83 17.76 14.65 12.17 10.35 6.97 4.84 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.03 27.17 17.99 14.69 12.80 10.67 7.09 4.92 -
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 38.62 30.08 26.50 22.05 15.75 13.23 9.72 7.40 6.30 5.04 4.21 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 33.74 29.69 24.76 17.68 14.84 10.91 8.31 7.09 5.67 4.72 -
3” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.68 27.20 19.45 16.34 11.97 9.17 7.80 6.22 5.04 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.43 29.53 21.06 17.72 12.99 9.92 8.43 6.73 5.08 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.07 31.73 22.64 18.78 13.98 10.67 9.06 7.24 5.12 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.82 24.13 18.98 14.76 11.38 9.69 7.44 5.16 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 19.17 14.76 12.05 10.24 7.52 5.24 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.83 27.01 22.68 14.80 12.72 10.83 7.64 5.28 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.39 23.86 14.84 13.39 11.30 7.72 5.35 -
Phase-Phase Distance
between axis (d): 8.25 inches
7.50
Short Circuit Current Rating (SCCR), 3 phases
Peak value Ipk (kA) 7.5 17 28 36 46.2 52.5 63 88.2 105 143 187 220 275 330 440
SCCR rms (kA) 5 10 14 18 22 25 30 42 50 65 85 100 125 150 200
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 31.54 27.76 23.11 16.50 13.86 10.16 7.76 6.61 5.28 4.41 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 35.35 31.10 25.91 18.50 15.55 11.42 8.70 7.40 5.91 4.92 -
3” X 1/4” 39.37 39.37 39.37 39.37 38.86 34.17 28.46 20.35 17.09 12.52 9.57 8.15 6.50 5.43 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.55 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 23.66 19.88 14.61 11.14 9.49 7.56 5.59 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.24 21.18 14.92 11.89 10.12 8.07 5.63 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.73 22.44 14.92 12.60 10.71 8.19 5.71 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.15 23.66 14.96 13.27 11.26 8.31 5.75 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.57 24.84 15.00 13.94 11.85 8.39 5.83 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 32.91 28.98 24.13 17.24 14.49 10.63 8.11 6.89 5.51 4.61 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.44 27.05 19.29 16.22 11.89 9.09 7.72 6.18 5.16 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.63 29.69 21.22 17.80 13.07 10.00 8.50 6.77 5.67 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.62 32.17 22.99 19.29 14.17 10.83 9.21 7.36 6.02 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.53 24.65 20.71 15.08 11.61 9.88 7.91 6.06 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 15.08 12.36 10.51 8.43 6.10 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 15.12 13.11 11.14 8.90 6.18 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 24.61 15.12 13.78 11.73 8.98 6.22 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.71 25.79 15.16 14.21 12.32 9.06 6.26 -
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 34.25 30.12 25.12 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 5.35 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.87 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 21.50 15.24 12.09 10.24 8.19 6.54 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.15 27.24 22.87 15.24 12.83 10.91 8.74 6.57 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.82 24.21 15.28 13.58 11.54 9.25 6.65 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 15.28 14.29 12.17 9.65 6.69 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 15.31 14.33 12.76 9.72 6.73 -
CABS142T / CABS142TN
Phase-Phase Distance
between axis (d): 2.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 28.70 22.32 17.36 15.28 12.76 9.09 7.64 5.59 4.29 - - - -
2.5” X 1/4” 39.37 39.37 33.66 26.18 20.39 17.95 14.96 10.67 8.98 6.57 5.04 - - - -
3” X 1/4” 39.37 39.37 38.50 29.92 23.31 20.51 17.09 12.20 10.24 7.52 5.55 4.02 - - -
3.5” X 1/4” 39.37 39.37 39.37 33.62 26.22 23.07 19.13 13.70 11.54 8.46 5.87 4.21 - - -
4” X 1/4” 39.37 39.37 39.37 37.28 29.06 25.55 21.30 14.76 12.76 9.37 6.14 4.45 - - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 31.85 28.03 23.35 14.84 14.02 10.28 6.46 4.65 - - -
5” X 1/4” 39.37 39.37 39.37 39.37 34.65 30.51 25.43 14.96 14.37 10.98 6.77 4.88 - - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 37.44 32.95 27.44 15.04 14.41 11.34 7.09 5.12 - - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.39 29.49 15.12 14.49 11.69 7.44 5.35 - - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 3.00 inches
Copper bar sizes (inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 30.47 23.70 18.46 16.22 13.54 9.65 8.11 5.94 4.53 - - - -
2.5” X 1/4” 39.37 39.37 35.71 27.76 21.61 19.02 15.87 11.34 9.49 6.97 5.31 4.53 - - -
3” X 1/4” 39.37 39.37 39.37 31.73 24.72 21.73 18.11 12.91 10.87 7.95 6.10 5.00 - - -
3.5” X 1/4” 39.37 39.37 39.37 35.55 27.72 24.37 20.31 14.49 12.17 8.94 6.81 5.20 - - -
4” X 1/4” 39.37 39.37 39.37 39.33 30.67 26.97 22.48 15.16 13.46 9.88 7.44 5.39 - - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 33.54 29.53 24.61 15.24 14.57 10.83 7.72 5.59 - - -
5” X 1/4” 39.37 39.37 39.37 39.37 36.42 32.05 26.69 15.31 14.61 11.77 8.03 5.79 - - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.25 34.53 28.78 15.39 14.69 12.60 8.35 6.02 - - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 15.47 14.76 12.91 8.66 6.22 3.98 - -
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 31.81 24.72 19.25 16.97 14.13 10.08 8.46 6.22 4.76 4.02 - - -
2.5” X 1/4” 39.37 39.37 37.32 29.02 22.60 19.88 16.57 11.85 9.92 7.28 5.55 4.72 - - -
3” X 1/4” 39.37 39.37 39.37 33.15 25.83 22.72 18.94 13.50 11.34 8.35 6.38 5.39 - - -
3.5” X 1/4” 39.37 39.37 39.37 37.17 28.94 25.47 21.22 15.16 12.72 9.33 7.13 6.06 3.94 - -
4” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 15.51 14.06 10.31 7.87 6.34 4.06 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 35.00 30.79 25.67 15.59 14.84 11.30 8.62 6.54 4.17 - -
5” X 1/4” 39.37 39.37 39.37 39.37 37.95 33.39 27.80 15.67 14.88 12.24 9.33 6.73 4.29 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.94 29.96 16.02 14.96 13.19 9.61 6.93 4.45 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.46 32.05 16.50 15.00 14.06 9.92 7.17 4.57 - -
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 32.83 25.55 19.88 17.52 14.61 10.43 8.74 6.42 4.88 4.17 - - -
2.5” X 1/4” 39.37 39.37 38.58 30.00 23.39 20.59 17.13 12.24 10.28 7.56 5.75 4.88 - - -
3” X 1/4” 39.37 39.37 39.37 34.33 26.73 23.50 19.61 13.98 11.73 8.62 6.57 5.59 4.49 - -
3.5” X 1/4” 39.37 39.37 39.37 38.46 29.96 26.38 21.97 15.71 13.19 9.69 7.40 6.26 4.61 - -
4” X 1/4” 39.37 39.37 39.37 39.37 33.15 29.13 24.29 16.97 14.57 10.71 8.19 6.93 4.69 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 36.22 31.89 26.57 17.36 15.12 11.69 8.94 7.52 4.80 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.25 34.53 28.78 17.80 15.16 12.68 9.69 7.72 4.92 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.17 30.98 18.23 15.24 13.62 10.43 7.91 5.04 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 18.66 15.28 14.21 10.75 8.11 5.16 - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 33.70 26.18 20.39 17.95 14.96 10.67 8.98 6.57 5.04 4.25 - - -
2.5” X 1/4” 39.37 39.37 39.37 30.83 24.02 21.14 17.60 12.56 10.55 7.76 5.91 5.04 4.02 - -
3” X 1/4” 39.37 39.37 39.37 35.28 27.48 24.17 20.16 14.37 12.09 8.86 6.77 5.75 4.61 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 30.83 27.13 22.60 16.14 13.54 9.96 7.60 6.46 5.16 - -
4” X 1/4” 39.37 39.37 39.37 39.37 34.09 30.00 25.00 17.83 15.00 10.98 8.43 7.13 5.35 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.28 32.80 27.32 19.53 15.39 12.05 9.21 7.80 5.43 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.55 29.61 21.14 15.43 13.03 9.96 8.46 5.55 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.27 31.89 22.76 15.47 14.02 10.71 8.86 5.67 3.94 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.09 24.33 15.55 14.37 11.46 9.06 5.79 4.02 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.37 26.73 20.83 18.31 15.28 10.91 9.13 6.73 5.12 4.37 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.50 24.53 21.61 17.99 12.83 10.79 7.91 6.06 5.16 4.09 - -
3” X 1/4” 39.37 39.37 39.37 36.10 28.11 24.72 20.63 14.72 12.36 9.06 6.93 5.91 4.72 3.94 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 31.57 27.80 23.15 16.54 13.90 10.20 7.80 6.61 5.28 4.09 -
4” X 1/4” 39.37 39.37 39.37 39.37 34.92 30.75 25.63 18.31 15.35 11.26 8.62 7.32 5.87 4.17 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 38.23 33.62 28.03 20.00 15.67 12.32 9.41 7.99 6.10 4.25 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 15.79 13.39 10.24 8.70 6.22 4.29 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.35 16.06 14.37 10.98 9.33 6.30 4.37 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.96 24.96 16.34 14.53 11.77 10.00 6.42 4.45 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.92 27.17 21.18 18.62 15.51 11.06 9.29 6.81 5.20 4.45 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.09 25.00 21.97 18.31 13.07 10.98 8.07 6.14 5.24 4.17 - -
3” X 1/4” 39.37 39.37 39.37 36.77 28.66 25.20 21.02 15.00 12.60 9.25 7.05 5.98 4.80 3.98 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.20 28.35 23.62 16.85 14.17 10.39 7.95 6.73 5.39 4.49 -
4” X 1/4” 39.37 39.37 39.37 39.37 35.67 31.38 26.14 18.66 15.67 11.50 8.78 7.48 5.98 4.65 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.02 34.33 28.62 20.43 17.17 12.60 9.61 8.19 6.54 4.69 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.24 31.02 22.17 17.48 13.66 10.43 8.86 6.85 4.76 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 17.72 14.65 11.22 9.53 6.97 4.84 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.71 25.51 17.99 14.69 12.01 10.20 7.05 4.88 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.43 27.56 21.46 18.90 15.75 11.22 9.45 6.93 5.28 4.49 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.56 25.35 22.32 18.58 13.27 11.14 8.19 6.26 5.31 4.25 - -
3” X 1/4” 39.37 39.37 39.37 37.36 29.13 25.63 21.34 15.24 12.80 9.41 7.17 6.10 4.88 4.06 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.76 28.82 24.02 17.17 14.41 10.55 8.07 6.85 5.47 4.57 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.30 31.93 26.61 19.02 15.94 11.69 8.94 7.60 6.06 5.08 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.96 29.13 20.79 17.48 12.83 9.80 8.35 6.65 5.16 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.91 31.61 22.56 18.94 13.90 10.63 9.02 7.20 5.24 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 20.39 14.80 11.46 9.72 7.64 5.28 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.38 25.98 21.81 14.80 12.24 10.39 7.72 5.35 -
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.83 27.87 21.69 19.09 15.91 11.38 9.53 7.01 5.35 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.95 25.67 22.60 18.82 13.43 11.30 8.27 6.34 5.39 4.29 - -
3” X 1/4” 39.37 39.37 39.37 37.87 29.53 25.98 21.65 15.47 12.99 9.53 7.28 6.18 4.96 4.13 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.23 29.25 24.37 17.40 14.61 10.71 8.19 6.97 5.55 4.65 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.85 32.40 27.01 19.29 16.18 11.89 9.09 7.72 6.18 5.16 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.51 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.54 32.13 22.91 19.25 14.13 10.79 9.17 7.32 5.67 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.75 14.96 11.65 9.88 7.91 5.75 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.01 26.42 22.20 15.00 12.44 10.59 8.39 5.83 -
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.18 28.15 21.93 19.29 16.06 11.46 9.65 7.09 5.39 4.61 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.35 25.98 22.83 19.06 13.58 11.42 8.39 6.42 5.43 4.33 - -
3” X 1/4” 39.37 39.37 39.37 38.35 29.88 26.30 21.89 15.63 13.15 9.65 7.36 6.26 5.00 4.17 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.66 29.61 24.69 17.60 14.80 10.87 8.31 7.05 5.63 4.69 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.32 32.83 27.36 19.53 16.42 12.05 9.21 7.83 6.26 5.20 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.98 30.00 21.42 17.99 13.19 10.08 8.58 6.85 5.71 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 19.53 14.33 10.94 9.33 7.44 6.14 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.08 25.04 21.06 15.12 11.81 10.04 8.03 6.22 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.56 26.81 22.52 15.16 12.64 10.75 8.58 6.26 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.50 28.39 22.13 19.45 16.22 11.57 9.72 7.13 5.43 4.65 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.66 26.22 23.07 19.21 13.74 11.54 8.46 6.46 5.47 4.37 - -
3” X 1/4” 39.37 39.37 39.37 38.74 30.20 26.54 22.13 15.79 13.27 9.72 7.44 6.34 5.04 4.21 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.02 29.92 24.96 17.80 14.96 10.98 8.39 7.13 5.71 4.76 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.76 33.23 27.68 19.76 16.61 12.20 9.33 7.91 6.34 5.28 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 18.23 13.39 10.24 8.70 6.93 5.79 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.99 23.54 19.76 14.53 11.10 9.45 7.56 6.30 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.55 25.39 21.34 15.28 11.97 10.16 8.11 6.69 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 22.83 15.31 12.80 10.87 8.70 6.73 -
CABS143T / CABS143TN
Phase-Phase Distance
between axis (d): 3.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 32.24 25.08 19.53 17.20 14.33 10.24 8.58 6.30 4.80 4.09 - - -
2.5” X 1/4” 39.37 39.37 36.61 28.46 22.20 19.53 16.26 11.61 9.76 7.17 5.47 4.65 - - -
3” X 1/4” 39.37 39.37 39.37 31.73 24.72 21.77 18.11 12.95 10.87 7.99 6.10 5.20 - - -
3.5” X 1/4” 39.37 39.37 39.37 34.92 27.20 23.94 19.92 14.25 11.97 8.78 6.69 5.51 - - -
4” X 1/4” 39.37 39.37 39.37 37.99 29.61 26.06 21.69 15.28 13.03 9.57 7.28 5.71 - - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 15.35 14.06 10.31 7.87 5.94 - - -
5” X 1/4” 39.37 39.37 39.37 39.37 34.37 30.24 25.20 15.43 14.72 11.10 8.46 6.14 3.94 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 36.69 32.28 26.93 15.55 14.80 11.85 8.86 6.38 4.09 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.06 34.37 28.62 15.63 14.84 12.60 9.17 6.61 4.25 - -
w
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.67 27.76 21.61 19.02 15.83 11.30 9.49 6.97 5.31 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.38 24.45 21.50 17.91 12.80 10.75 7.87 6.02 5.12 3.98 - -
3” X 1/4” 39.37 39.37 39.37 34.76 27.09 23.86 19.88 14.17 11.93 8.74 6.69 5.67 4.09 - -
3.5” X 1/4” 39.37 39.37 39.37 38.07 29.65 26.10 21.73 15.51 13.03 9.57 7.32 6.22 4.17 - -
4” X 1/4” 39.37 39.37 39.37 39.37 32.17 28.31 23.58 15.67 14.13 10.39 7.91 6.73 4.29 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 34.61 30.47 25.39 16.02 14.96 11.18 8.54 6.93 4.45 - -
5” X 1/4” 39.37 39.37 39.37 39.37 37.01 32.60 27.17 16.50 15.00 11.97 9.13 7.17 4.57 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.69 28.90 17.01 15.08 12.72 9.72 7.36 4.72 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 17.52 15.12 13.50 10.31 7.60 4.84 - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 38.82 30.20 23.54 20.71 17.24 12.32 10.35 7.60 5.79 4.92 3.94 - -
2.5” X 1/4” 39.37 39.37 39.37 34.06 26.54 23.35 19.45 13.90 11.65 8.54 6.54 5.55 4.45 - -
3” X 1/4” 39.37 39.37 39.37 37.64 29.33 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.76 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 16.77 14.06 10.31 7.87 6.69 4.88 - -
4” X 1/4” 39.37 39.37 39.37 39.37 34.57 30.43 25.35 17.99 15.20 11.14 8.54 7.24 5.00 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.64 27.20 18.43 15.24 11.97 9.13 7.80 5.12 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.84 29.02 18.86 15.28 12.76 9.76 8.19 5.24 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.97 30.83 22.01 15.35 13.58 10.35 8.39 5.35 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.60 23.27 15.39 14.29 10.94 8.58 5.47 - -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.48 25.31 22.28 18.54 13.27 11.14 8.15 6.26 5.31 4.25 - -
2.5” X 1/4” 39.37 39.37 39.37 36.57 28.46 25.08 20.87 14.92 12.52 9.17 7.01 5.98 4.76 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.42 27.64 23.03 16.46 13.82 10.16 7.76 6.57 5.28 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.02 8.43 7.17 5.59 - -
4” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.48 27.05 19.33 15.47 11.89 9.09 7.72 5.67 3.94 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.76 28.98 20.67 15.55 12.76 9.76 8.27 5.79 4.02 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.01 30.83 22.01 15.59 13.58 10.35 8.82 5.91 4.09 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.31 15.63 14.37 10.98 9.33 6.02 4.17 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 15.67 14.45 11.61 9.61 6.14 4.25 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 34.65 27.01 23.74 19.80 14.13 11.85 8.70 6.65 5.67 4.53 - -
2.5” X 1/4” 39.37 39.37 39.37 38.94 30.31 26.69 22.24 15.87 13.35 9.80 7.48 6.34 5.08 4.21 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.43 29.41 24.49 17.48 14.69 10.79 8.23 7.01 5.59 4.29 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 36.34 31.97 26.65 19.02 15.98 11.73 8.98 7.60 6.10 4.37 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.09 34.41 28.66 20.47 16.26 12.64 9.65 8.19 6.38 4.41 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 21.89 16.50 13.50 10.31 8.78 6.50 4.49 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 16.77 14.33 10.94 9.33 6.57 4.57 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 17.05 14.57 11.57 9.84 6.69 4.65 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.30 25.91 17.32 14.61 12.20 10.39 6.81 4.72 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 36.69 28.58 25.16 20.94 14.96 12.56 9.21 7.05 5.98 4.80 3.98 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 32.09 28.23 23.50 16.81 14.09 10.35 7.91 6.73 5.35 4.49 -
3” X 1/4” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.80 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 4.88 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.26 30.24 21.57 18.03 13.31 10.16 8.62 6.89 4.92 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.70 32.24 23.03 18.27 14.21 10.87 9.21 7.17 5.00 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.25 24.45 18.50 14.72 11.54 9.80 7.28 5.04 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.18 25.83 18.78 14.72 12.17 10.35 7.40 5.12 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.03 27.17 19.06 14.76 12.80 10.87 7.48 5.20 -
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 38.62 30.08 26.50 22.05 15.75 13.23 9.72 7.40 6.30 5.04 4.21 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 33.74 29.69 24.76 17.68 14.84 10.91 8.31 7.09 5.67 4.72 -
3” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.68 27.20 19.45 16.34 11.97 9.17 7.80 6.22 5.20 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.43 29.53 21.06 17.72 12.99 9.92 8.43 6.73 5.35 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.07 31.73 22.64 19.02 13.98 10.67 9.06 7.24 5.43 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.82 24.13 20.28 14.88 11.38 9.69 7.72 5.47 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 21.50 14.88 12.05 10.24 7.99 5.55 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.83 27.01 22.68 14.92 12.72 10.83 8.07 5.59 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.39 23.86 14.92 13.39 11.38 8.19 5.67 -
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 31.54 27.76 23.11 16.50 13.86 10.16 7.76 6.61 5.28 4.41 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 35.35 31.10 25.91 18.50 15.55 11.42 8.70 7.40 5.91 4.92 -
3” X 1/4” 39.37 39.37 39.37 39.37 38.86 34.17 28.46 20.35 17.09 12.52 9.57 8.15 6.50 5.43 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.87 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 23.66 19.88 14.61 11.14 9.49 7.56 5.91 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.24 21.18 15.04 11.89 10.12 8.07 5.98 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.73 22.44 15.04 12.60 10.71 8.54 6.02 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.15 23.66 15.08 13.27 11.26 8.78 6.10 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.57 24.84 15.12 13.94 11.85 8.90 6.14 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 32.91 28.98 24.13 17.24 14.49 10.63 8.11 6.89 5.51 4.61 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.44 27.05 19.29 16.22 11.89 9.09 7.72 6.18 5.16 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.63 29.69 21.22 17.80 13.07 10.00 8.50 6.77 5.67 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.62 32.17 22.99 19.29 14.17 10.83 9.21 7.36 6.14 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.53 24.65 20.71 15.20 11.61 9.88 7.91 6.42 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 15.20 12.36 10.51 8.43 6.46 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 15.24 13.11 11.14 8.90 6.54 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 24.61 15.24 13.78 11.73 9.37 6.57 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.71 25.79 15.28 14.29 12.32 9.57 6.65 -
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 34.25 30.12 25.12 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 5.35 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.87 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 21.50 15.35 12.09 10.24 8.19 6.81 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.15 27.24 22.87 15.39 12.83 10.91 8.74 6.97 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.82 24.21 15.39 13.58 11.54 9.25 7.01 3.94
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 15.39 14.29 12.17 9.72 7.09 3.98
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 15.43 14.41 12.76 10.16 7.13 4.02
CABS143T / CABS143TN
Phase-Phase Distance
between axis (d): 3.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 30.47 23.70 18.46 16.22 13.54 9.65 8.11 5.94 4.53 - - - -
2.5” X 1/4” 39.37 39.37 35.71 27.76 21.61 19.02 15.87 11.34 9.49 6.97 5.31 4.53 - - -
3” X 1/4” 39.37 39.37 39.37 31.73 24.72 21.73 18.11 12.91 10.87 7.95 6.10 5.16 4.13 - -
3.5” X 1/4” 39.37 39.37 39.37 35.55 27.72 24.37 20.31 14.49 12.17 8.94 6.81 5.79 4.65 - -
4” X 1/4” 39.37 39.37 39.37 39.33 30.67 26.97 22.48 16.06 13.46 9.88 7.56 6.42 4.84 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 33.54 29.53 24.61 17.56 14.76 10.83 8.27 7.05 5.04 - -
5” X 1/4” 39.37 39.37 39.37 39.37 36.42 32.05 26.69 18.90 15.31 11.77 8.98 7.64 5.24 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.25 34.53 28.78 20.55 15.39 12.68 9.69 8.23 5.43 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 15.47 13.58 10.39 8.82 5.63 - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 31.81 24.72 19.25 16.97 14.13 10.08 8.46 6.22 4.76 4.02 - - -
2.5” X 1/4” 39.37 39.37 37.32 29.02 22.60 19.88 16.57 11.85 9.92 7.28 5.55 4.72 - - -
3” X 1/4” 39.37 39.37 39.37 33.15 25.83 22.72 18.94 13.50 11.34 8.35 6.38 5.39 4.33 - -
3.5” X 1/4” 39.37 39.37 39.37 37.17 28.94 25.47 21.22 15.16 12.72 9.33 7.13 6.06 4.84 - -
4” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 16.73 14.06 10.31 7.87 6.69 5.35 3.98 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 35.00 30.79 25.67 18.31 15.39 11.30 8.62 7.32 5.87 4.09 -
5” X 1/4” 39.37 39.37 39.37 39.37 37.95 33.39 27.80 19.84 15.67 12.24 9.37 7.95 6.10 4.21 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.94 29.96 21.38 15.94 13.19 10.08 8.54 6.26 4.33 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.46 32.05 22.91 16.46 14.13 10.79 9.17 6.46 4.49 -
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 32.83 25.55 19.88 17.52 14.61 10.43 8.74 6.42 4.88 4.17 - - -
2.5” X 1/4” 39.37 39.37 38.58 30.00 23.39 20.59 17.13 12.24 10.28 7.56 5.75 4.88 - - -
3” X 1/4” 39.37 39.37 39.37 34.33 26.73 23.50 19.61 13.98 11.73 8.62 6.57 5.59 4.49 - -
3.5” X 1/4” 39.37 39.37 39.37 38.46 29.96 26.38 21.97 15.71 13.19 9.69 7.40 6.26 5.00 4.17 -
4” X 1/4” 39.37 39.37 39.37 39.37 33.15 29.13 24.29 17.36 14.57 10.71 8.19 6.93 5.55 4.61 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 36.22 31.89 26.57 18.98 15.94 11.69 8.94 7.60 6.06 4.72 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.25 34.53 28.78 20.55 17.24 12.68 9.69 8.23 6.57 4.84 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.17 30.98 22.13 18.15 13.62 10.43 8.86 7.09 4.96 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 23.66 18.62 14.61 11.14 9.49 7.32 5.08 -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 33.70 26.18 20.39 17.95 14.96 10.67 8.98 6.57 5.04 4.25 - - -
2.5” X 1/4” 39.37 39.37 39.37 30.83 24.02 21.14 17.60 12.56 10.55 7.76 5.91 5.04 4.02 - -
3” X 1/4” 39.37 39.37 39.37 35.28 27.48 24.17 20.16 14.37 12.09 8.86 6.77 5.75 4.61 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 30.83 27.13 22.60 16.14 13.54 9.96 7.60 6.46 5.16 4.29 -
4” X 1/4” 39.37 39.37 39.37 39.37 34.09 30.00 25.00 17.83 15.00 10.98 8.43 7.13 5.71 4.76 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.28 32.80 27.32 19.53 16.38 12.05 9.21 7.80 6.26 5.20 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.55 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.43 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.27 31.89 22.76 19.13 14.02 10.71 9.09 7.28 5.55 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.09 24.33 20.43 14.92 11.46 9.76 7.80 5.67 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.37 26.73 20.83 18.31 15.28 10.91 9.13 6.73 5.12 4.37 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.50 24.53 21.61 17.99 12.83 10.79 7.91 6.06 5.16 4.09 - -
3” X 1/4” 39.37 39.37 39.37 36.10 28.11 24.72 20.63 14.72 12.36 9.06 6.93 5.91 4.72 3.94 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 31.57 27.80 23.15 16.54 13.90 10.20 7.80 6.61 5.28 4.41 -
4” X 1/4” 39.37 39.37 39.37 39.37 34.92 30.75 25.63 18.31 15.35 11.26 8.62 7.32 5.87 4.88 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 38.23 33.62 28.03 20.00 16.81 12.32 9.41 7.99 6.42 5.31 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 18.23 13.39 10.24 8.70 6.93 5.79 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.35 19.61 14.37 10.98 9.33 7.48 6.18 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.96 24.96 20.94 15.16 11.77 10.00 7.99 6.30 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.92 27.17 21.18 18.62 15.51 11.06 9.29 6.81 5.20 4.45 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.09 25.00 21.97 18.31 13.07 10.98 8.07 6.14 5.24 4.17 - -
3” X 1/4” 39.37 39.37 39.37 36.77 28.66 25.20 21.02 15.00 12.60 9.25 7.05 5.98 4.80 3.98 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.20 28.35 23.62 16.85 14.17 10.39 7.95 6.73 5.39 4.49 -
4” X 1/4” 39.37 39.37 39.37 39.37 35.67 31.38 26.14 18.66 15.67 11.50 8.78 7.48 5.98 4.96 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.02 34.33 28.62 20.43 17.17 12.60 9.61 8.19 6.54 5.43 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.24 31.02 22.17 18.62 13.66 10.43 8.86 7.09 5.91 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.04 14.69 11.22 9.53 7.64 6.34 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.71 25.51 21.42 15.35 12.01 10.20 8.15 6.81 -
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.43 27.56 21.46 18.90 15.75 11.22 9.45 6.93 5.28 4.49 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.56 25.35 22.32 18.58 13.27 11.14 8.19 6.26 5.31 4.25 - -
3” X 1/4” 39.37 39.37 39.37 37.36 29.13 25.63 21.34 15.24 12.80 9.41 7.17 6.10 4.88 4.06 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.76 28.82 24.02 17.17 14.41 10.55 8.07 6.85 5.47 4.57 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.30 31.93 26.61 19.02 15.94 11.69 8.94 7.60 6.06 5.08 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.96 29.13 20.79 17.48 12.83 9.80 8.35 6.65 5.55 4.09
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.91 31.61 22.56 18.94 13.90 10.63 9.02 7.20 6.02 4.13
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 20.39 14.96 11.46 9.72 7.80 6.50 4.21
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.38 25.98 21.81 15.59 12.24 10.39 8.31 6.93 4.25
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.83 27.87 21.69 19.09 15.91 11.38 9.53 7.01 5.35 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.95 25.67 22.60 18.82 13.43 11.30 8.27 6.34 5.39 4.29 - -
3” X 1/4” 39.37 39.37 39.37 37.87 29.53 25.98 21.65 15.47 12.99 9.53 7.28 6.18 4.96 4.13 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.23 29.25 24.37 17.40 14.61 10.71 8.19 6.97 5.55 4.65 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.85 32.40 27.01 19.29 16.18 11.89 9.09 7.72 6.18 5.16 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.51 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 4.21
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.54 32.13 22.91 19.25 14.13 10.79 9.17 7.32 6.10 4.53
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.75 15.24 11.65 9.88 7.91 6.57 4.57
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.01 26.42 22.20 16.22 12.44 10.59 8.46 7.05 4.61
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.18 28.15 21.93 19.29 16.06 11.46 9.65 7.09 5.39 4.61 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.35 25.98 22.83 19.06 13.58 11.42 8.39 6.42 5.43 4.33 - -
3” X 1/4” 39.37 39.37 39.37 38.35 29.88 26.30 21.89 15.63 13.15 9.65 7.36 6.26 5.00 4.17 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.66 29.61 24.69 17.60 14.80 10.87 8.31 7.05 5.63 4.69 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.32 32.83 27.36 19.53 16.42 12.05 9.21 7.83 6.26 5.20 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.98 30.00 21.42 17.99 13.19 10.08 8.58 6.85 5.71 4.29
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 19.53 14.33 10.94 9.33 7.44 6.22 4.65
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.08 25.04 21.06 15.43 11.81 10.04 8.03 6.69 4.92
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.56 26.81 22.52 16.54 12.64 10.75 8.58 7.17 4.96
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.50 28.39 22.13 19.45 16.22 11.57 9.72 7.13 5.43 4.65 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.66 26.22 23.07 19.21 13.74 11.54 8.46 6.46 5.47 4.37 - -
3” X 1/4” 39.37 39.37 39.37 38.74 30.20 26.54 22.13 15.79 13.27 9.72 7.44 6.34 5.04 4.21 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.02 29.92 24.96 17.80 14.96 10.98 8.39 7.13 5.71 4.76 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.76 33.23 27.68 19.76 16.61 12.20 9.33 7.91 6.34 5.28 3.94
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 18.23 13.39 10.24 8.70 6.93 5.79 4.33
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.99 23.54 19.76 14.53 11.10 9.45 7.56 6.30 4.72
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.55 25.39 21.34 15.63 11.97 10.16 8.11 6.77 5.08
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 22.83 16.77 12.80 10.87 8.70 7.24 5.35
Data and Calculations are only recommendations and for ERIFLEX’s products only
CABS143T / CABS143TN
Phase-Phase Distance
between axis (d): 3.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.75 27.80 21.65 19.06 15.87 11.34 9.53 6.97 5.35 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.48 25.31 22.28 18.54 13.27 11.14 8.15 6.22 5.31 4.25 - -
3” X 1/4” 39.37 39.37 39.37 37.05 28.86 25.39 21.18 15.12 12.68 9.33 7.13 6.06 4.57 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.32 28.46 23.70 16.93 14.21 10.43 7.99 6.77 4.76 - -
4” X 1/4” 39.37 39.37 39.37 39.37 35.75 31.46 26.22 17.83 15.16 11.54 8.82 7.48 4.92 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.13 34.41 28.70 18.54 15.24 12.64 9.65 8.03 5.12 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.36 31.14 22.24 15.35 13.70 10.47 8.35 5.35 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.54 23.98 15.43 14.29 11.26 8.66 5.55 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.98 25.67 15.51 14.33 11.54 9.02 5.75 3.98 -
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 37.24 28.98 22.56 19.84 16.54 11.81 9.92 7.28 5.55 4.72 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.86 26.38 23.23 19.33 13.82 11.61 8.50 6.50 5.51 4.41 - -
3” X 1/4” 39.37 39.37 39.37 38.58 30.08 26.46 22.05 15.75 13.23 9.69 7.40 6.30 5.04 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.66 29.65 24.69 17.64 14.80 10.87 8.31 7.05 5.63 3.94 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.20 32.72 27.28 19.49 15.55 12.01 9.17 7.80 5.83 4.06 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.79 29.80 21.30 15.63 13.11 10.04 8.50 6.02 4.17 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.78 32.32 23.07 15.79 14.21 10.87 9.25 6.22 4.29 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.80 24.84 16.30 14.49 11.69 9.96 6.42 4.45 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.24 26.61 16.81 14.57 12.52 10.20 6.61 4.57 -
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 38.39 29.84 23.27 20.47 17.05 12.17 10.24 7.52 5.75 4.88 - - -
2.5” X 1/4” 39.37 39.37 39.37 34.96 27.20 23.94 19.96 14.25 11.97 8.78 6.69 5.71 4.57 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.06 27.32 22.76 16.26 13.66 10.00 7.64 6.50 5.20 4.33 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.76 30.59 25.47 18.19 15.28 11.22 8.58 7.28 5.83 4.61 -
4” X 1/4” 39.37 39.37 39.37 39.37 38.39 33.78 28.15 20.12 16.89 12.40 9.49 8.03 6.42 4.69 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.93 30.75 21.97 17.68 13.54 10.35 8.78 6.93 4.80 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.35 23.82 18.11 14.69 11.22 9.53 7.13 4.92 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.63 18.54 14.72 12.09 10.28 7.28 5.04 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.39 27.40 19.02 14.76 12.91 10.98 7.48 5.20 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.29 30.55 23.82 20.94 17.44 12.48 10.47 7.68 5.87 5.00 3.98 - -
2.5” X 1/4” 39.37 39.37 39.37 35.83 27.91 24.57 20.47 14.61 12.28 9.02 6.89 5.83 4.69 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.85 28.03 23.35 16.65 14.02 10.28 7.83 6.65 5.31 4.45 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 35.67 31.38 26.14 18.66 15.67 11.50 8.78 7.48 5.98 4.96 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.69 28.90 20.63 17.32 12.72 9.72 8.27 6.61 5.35 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.91 31.57 22.56 18.94 13.90 10.63 9.02 7.20 5.47 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.21 24.45 20.51 14.88 11.50 9.76 7.83 5.59 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.81 26.30 22.09 14.92 12.40 10.51 8.19 5.67 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.11 23.62 14.96 13.27 11.26 8.39 5.83 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 31.14 24.25 21.34 17.80 12.68 10.67 7.83 5.98 5.08 4.06 - -
2.5” X 1/4” 39.37 39.37 39.37 36.54 28.46 25.04 20.87 14.88 12.52 9.17 7.01 5.94 4.76 3.98 -
3” X 1/4” 39.37 39.37 39.37 39.37 32.52 28.62 23.82 17.01 14.29 10.47 8.03 6.81 5.43 4.53 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 36.46 32.05 26.73 19.09 16.02 11.77 8.98 7.64 6.10 5.08 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.43 29.53 21.10 17.72 12.99 9.92 8.43 6.73 5.63 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.74 32.28 23.03 19.37 14.21 10.87 9.21 7.36 6.14 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.96 24.96 20.98 15.12 11.77 10.00 7.99 6.22 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 22.56 15.16 12.68 10.75 8.62 6.34 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.74 24.13 15.20 13.54 11.50 9.21 6.46 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 31.61 24.61 21.65 18.03 12.87 10.83 7.95 6.06 5.16 4.13 - -
2.5” X 1/4” 39.37 39.37 39.37 37.13 28.90 25.43 21.18 15.12 12.72 9.33 7.13 6.06 4.84 4.02 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.07 29.09 24.25 17.32 14.53 10.67 8.15 6.93 5.55 4.61 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 37.09 32.64 27.20 19.41 16.30 11.97 9.13 7.76 6.22 5.16 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.10 30.08 21.46 18.03 13.23 10.12 8.58 6.89 5.71 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.87 23.46 19.72 14.49 11.06 9.41 7.52 6.26 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.63 25.47 21.38 15.35 12.01 10.20 8.15 6.77 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.35 27.40 22.99 15.39 12.91 10.98 8.78 6.97 3.94
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 24.61 15.43 13.82 11.73 9.37 7.09 3.98
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.01 24.92 21.93 18.27 13.03 10.94 8.03 6.14 5.24 4.17 - -
2.5” X 1/4” 39.37 39.37 39.37 37.60 29.29 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.92 4.09 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.54 29.53 24.61 17.56 14.76 10.83 8.27 7.01 5.63 4.69 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 37.64 33.11 27.60 19.72 16.54 12.17 9.29 7.87 6.30 5.24 3.94
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.65 30.55 21.81 18.31 13.43 10.28 8.74 6.97 5.83 4.13
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.86 20.04 14.72 11.26 9.57 7.64 6.38 4.21
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.22 25.87 21.73 15.55 12.20 10.35 8.27 6.89 4.25
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.98 27.83 23.39 15.59 13.11 11.14 8.94 7.44 4.29
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.80 25.04 15.63 14.06 11.93 9.53 7.76 4.33
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.32 25.20 22.17 18.46 13.19 11.06 8.11 6.22 5.28 4.21 - -
2.5” X 1/4” 39.37 39.37 39.37 38.03 29.65 26.06 21.73 15.51 13.03 9.57 7.32 6.22 4.96 4.13 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.94 29.88 24.88 17.76 14.92 10.94 8.39 7.13 5.67 4.72 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.15 33.54 27.95 19.96 16.77 12.32 9.41 7.99 6.38 5.31 3.98
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.13 30.94 22.09 18.54 13.62 10.43 8.86 7.09 5.91 4.41
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.86 24.17 20.31 14.92 11.42 9.69 7.76 6.46 4.57
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.73 26.26 22.05 16.18 12.36 10.51 8.39 7.01 4.61
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 16.42 13.31 11.30 9.06 7.52 4.69
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.24 25.39 16.61 14.25 12.13 9.69 8.07 4.72
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.64 25.39 22.36 18.62 13.31 11.18 8.19 6.26 5.31 4.25 - -
2.5” X 1/4” 39.37 39.37 39.37 38.43 29.92 26.34 21.93 15.67 13.15 9.65 7.36 6.26 5.00 4.17 -
3” X 1/4” 39.37 39.37 39.37 39.37 34.29 30.20 25.16 17.95 15.08 11.06 8.46 7.20 5.75 4.80 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.54 33.94 28.27 20.20 16.97 12.44 9.53 8.07 6.46 5.39 4.02
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.56 31.30 22.36 18.78 13.78 10.55 8.94 7.17 5.94 4.45
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.29 24.49 20.55 15.08 11.54 9.80 7.83 6.54 4.88
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.20 26.57 22.32 16.38 12.52 10.63 8.50 7.09 5.00
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.62 24.06 17.64 13.50 11.46 9.17 7.64 5.04
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.63 25.75 17.91 14.45 12.28 9.80 8.19 5.12
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.87 25.59 22.52 18.78 13.39 11.26 8.27 6.30 5.35 4.29 - -
2.5” X 1/4” 39.37 39.37 39.37 38.74 30.20 26.57 22.13 15.79 13.27 9.72 7.44 6.34 5.04 4.21 -
3” X 1/4” 39.37 39.37 39.37 39.37 34.61 30.47 25.39 18.11 15.24 11.18 8.54 7.24 5.79 4.84 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.94 34.25 28.54 20.39 17.13 12.56 9.61 8.15 6.54 5.43 4.06
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.95 31.61 22.60 18.98 13.94 10.63 9.06 7.24 6.02 4.53
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.65 24.76 20.79 15.28 11.65 9.92 7.91 6.61 4.96
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.85 22.56 16.57 12.68 10.75 8.62 7.17 5.35
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.94 24.29 17.83 13.62 11.57 9.25 7.72 5.43
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.98 26.02 19.09 14.61 12.40 9.92 8.27 5.47
CABS144T / CABS144TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.67 27.76 21.61 19.02 15.83 11.30 9.49 6.97 5.31 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.38 24.45 21.50 17.91 12.80 10.75 7.87 6.02 5.12 - - -
3” X 1/4” 39.37 39.37 39.37 34.76 27.09 23.86 19.88 14.17 11.93 8.74 6.69 5.67 3.98 - -
3.5” X 1/4” 39.37 39.37 39.37 38.07 29.65 26.10 21.73 15.51 13.03 9.57 7.32 6.22 4.06 - -
4” X 1/4” 39.37 39.37 39.37 39.37 32.17 28.31 23.58 15.59 14.13 10.39 7.91 6.57 4.17 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 34.61 30.47 25.39 15.67 14.88 11.18 8.54 6.73 4.33 - -
5” X 1/4” 39.37 39.37 39.37 39.37 37.01 32.60 27.17 16.06 14.96 11.97 9.13 6.97 4.45 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.69 28.90 16.54 15.00 12.72 9.72 7.17 4.57 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 17.05 15.08 13.50 10.12 7.36 4.72 - -
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 38.82 30.20 23.54 20.71 17.24 12.32 10.35 7.60 5.79 4.92 3.94 - -
2.5” X 1/4” 39.37 39.37 39.37 34.06 26.54 23.35 19.45 13.90 11.65 8.54 6.54 5.55 4.45 - -
3” X 1/4” 39.37 39.37 39.37 37.64 29.33 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.65 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 16.77 14.06 10.31 7.87 6.69 4.72 - -
4” X 1/4” 39.37 39.37 39.37 39.37 34.57 30.43 25.35 17.52 15.12 11.14 8.54 7.24 4.84 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.64 27.20 17.91 15.20 11.97 9.13 7.76 4.96 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.84 29.02 18.35 15.24 12.76 9.76 7.95 5.08 - -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.97 30.83 18.78 15.28 13.58 10.35 8.15 5.20 - -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.60 23.27 15.35 14.25 10.94 8.35 5.35 - -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.48 25.31 22.28 18.54 13.27 11.14 8.15 6.26 5.31 4.25 - -
2.5” X 1/4” 39.37 39.37 39.37 36.57 28.46 25.08 20.87 14.92 12.52 9.17 7.01 5.98 4.76 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.42 27.64 23.03 16.46 13.82 10.16 7.76 6.57 5.28 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.02 8.43 7.17 5.43 - -
4” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.48 27.05 19.33 15.43 11.89 9.09 7.72 5.51 - -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.76 28.98 20.67 15.47 12.76 9.76 8.27 5.63 - -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.01 30.83 22.01 15.51 13.58 10.35 8.82 5.75 3.98 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.31 15.55 14.37 10.98 9.13 5.87 4.06 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 15.63 14.41 11.61 9.33 5.98 4.13 -
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 34.65 27.01 23.74 19.80 14.13 11.85 8.70 6.65 5.67 4.53 - -
2.5” X 1/4” 39.37 39.37 39.37 38.94 30.31 26.69 22.24 15.87 13.35 9.80 7.48 6.34 5.08 4.13 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.43 29.41 24.49 17.48 14.69 10.79 8.23 7.01 5.59 4.17 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 36.34 31.97 26.65 19.02 15.67 11.73 8.98 7.60 6.10 4.25 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.09 34.41 28.66 20.47 15.79 12.64 9.65 8.19 6.22 4.29 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.77 30.63 21.89 16.02 13.50 10.31 8.78 6.30 4.37 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 16.30 14.33 10.94 9.33 6.42 4.45 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 24.61 16.57 14.53 11.57 9.84 6.50 4.53 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.30 25.91 16.85 14.57 12.20 10.20 6.61 4.61 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 36.69 28.58 25.16 20.94 14.96 12.56 9.21 7.05 5.98 4.80 3.98 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 32.09 28.23 23.50 16.81 14.09 10.35 7.91 6.73 5.35 4.49 -
3” X 1/4” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.69 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 4.72 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.26 30.24 21.57 17.56 13.31 10.16 8.62 6.89 4.76 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.70 32.24 23.03 17.76 14.21 10.87 9.21 6.97 4.84 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.25 24.45 17.99 14.69 11.54 9.80 7.09 4.92 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.18 25.83 18.27 14.69 12.17 10.35 7.17 4.96 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.03 27.17 18.54 14.72 12.80 10.87 7.28 5.04 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 38.62 30.08 26.50 22.05 15.75 13.23 9.72 7.40 6.30 5.04 4.21 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 33.74 29.69 24.76 17.68 14.84 10.91 8.31 7.09 5.67 4.72 -
3” X 1/4” 39.37 39.37 39.37 39.37 37.13 32.68 27.20 19.45 16.34 11.97 9.17 7.80 6.22 5.16 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.43 29.53 21.06 17.72 12.99 9.92 8.43 6.73 5.20 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.07 31.73 22.64 19.02 13.98 10.67 9.06 7.24 5.28 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.82 24.13 20.28 14.80 11.38 9.69 7.68 5.31 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 21.50 14.84 12.05 10.24 7.76 5.39 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.83 27.01 22.68 14.84 12.72 10.83 7.83 5.43 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.39 23.86 14.88 13.39 11.38 7.95 5.51 -
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 31.54 27.76 23.11 16.50 13.86 10.16 7.76 6.61 5.28 4.41 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 35.35 31.10 25.91 18.50 15.55 11.42 8.70 7.40 5.91 4.92 -
3” X 1/4” 39.37 39.37 39.37 39.37 38.86 34.17 28.46 20.35 17.09 12.52 9.57 8.15 6.50 5.43 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.71 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 23.66 19.88 14.61 11.14 9.49 7.56 5.75 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.24 21.18 14.96 11.89 10.12 8.07 5.79 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.73 22.44 15.00 12.60 10.71 8.46 5.87 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.15 23.66 15.00 13.27 11.26 8.54 5.91 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.57 24.84 15.04 13.94 11.85 8.62 5.98 -
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 32.91 28.98 24.13 17.24 14.49 10.63 8.11 6.89 5.51 4.61 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 36.89 32.44 27.05 19.29 16.22 11.89 9.09 7.72 6.18 5.16 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.63 29.69 21.22 17.80 13.07 10.00 8.50 6.77 5.67 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.62 32.17 22.99 19.29 14.17 10.83 9.21 7.36 6.14 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.53 24.65 20.71 15.12 11.61 9.88 7.91 6.26 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 15.16 12.36 10.51 8.43 6.30 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 15.16 13.11 11.14 8.90 6.34 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 24.61 15.20 13.78 11.73 9.21 6.42 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.71 25.79 15.20 14.25 12.32 9.33 6.46 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 39.37 34.25 30.12 25.12 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 38.35 33.74 28.11 20.08 16.85 12.36 9.45 8.03 6.42 5.35 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.05 30.87 22.05 18.50 13.58 10.39 8.82 7.05 5.87 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.59 21.50 15.28 12.09 10.24 8.19 6.73 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.15 27.24 22.87 15.31 12.83 10.91 8.74 6.77 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.82 24.21 15.31 13.58 11.54 9.25 6.85 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 15.35 14.29 12.17 9.72 6.89 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 15.35 14.37 12.76 10.00 6.93 -
CABS144T / CABS144TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 31.81 24.72 19.25 16.97 14.13 10.08 8.46 6.22 4.76 4.02 - - -
2.5” X 1/4” 39.37 39.37 37.32 29.02 22.60 19.88 16.57 11.85 9.92 7.28 5.55 4.72 - - -
3” X 1/4” 39.37 39.37 39.37 33.15 25.83 22.72 18.94 13.50 11.34 8.35 6.38 5.39 4.33 - -
3.5” X 1/4” 39.37 39.37 39.37 37.17 28.94 25.47 21.22 15.16 12.72 9.33 7.13 6.06 4.84 4.02 -
4” X 1/4” 39.37 39.37 39.37 39.37 32.01 28.15 23.46 16.73 14.06 10.31 7.87 6.69 5.35 4.45 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 35.00 30.79 25.67 18.31 15.39 11.30 8.62 7.32 5.87 4.88 -
5” X 1/4” 39.37 39.37 39.37 39.37 37.95 33.39 27.80 19.84 16.69 12.24 9.37 7.95 6.34 5.20 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.94 29.96 21.38 17.95 13.19 10.08 8.54 6.85 5.35 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.46 32.05 22.91 19.21 14.13 10.79 9.17 7.32 5.51 -
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 32.83 25.55 19.88 17.52 14.61 10.43 8.74 6.42 4.88 4.17 - - -
2.5” X 1/4” 39.37 39.37 38.58 30.00 23.39 20.59 17.13 12.24 10.28 7.56 5.75 4.88 - - -
3” X 1/4” 39.37 39.37 39.37 34.33 26.73 23.50 19.61 13.98 11.73 8.62 6.57 5.59 4.49 - -
3.5” X 1/4” 39.37 39.37 39.37 38.46 29.96 26.38 21.97 15.71 13.19 9.69 7.40 6.26 5.00 4.17 -
4” X 1/4” 39.37 39.37 39.37 39.37 33.15 29.13 24.29 17.36 14.57 10.71 8.19 6.93 5.55 4.61 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 36.22 31.89 26.57 18.98 15.94 11.69 8.94 7.60 6.06 5.04 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.25 34.53 28.78 20.55 17.24 12.68 9.69 8.23 6.57 5.47 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.17 30.98 22.13 18.58 13.62 10.43 8.86 7.09 5.91 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.15 23.66 19.88 14.61 11.14 9.49 7.56 6.22 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 33.70 26.18 20.39 17.95 14.96 10.67 8.98 6.57 5.04 4.25 - - -
2.5” X 1/4” 39.37 39.37 39.37 30.83 24.02 21.14 17.60 12.56 10.55 7.76 5.91 5.04 4.02 - -
3” X 1/4” 39.37 39.37 39.37 35.28 27.48 24.17 20.16 14.37 12.09 8.86 6.77 5.75 4.61 - -
3.5” X 1/4” 39.37 39.37 39.37 39.37 30.83 27.13 22.60 16.14 13.54 9.96 7.60 6.46 5.16 4.29 -
4” X 1/4” 39.37 39.37 39.37 39.37 34.09 30.00 25.00 17.83 15.00 10.98 8.43 7.13 5.71 4.76 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 37.28 32.80 27.32 19.53 16.38 12.05 9.21 7.80 6.26 5.20 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.55 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.27 31.89 22.76 19.13 14.02 10.71 9.09 7.28 6.06 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.09 24.33 20.43 15.00 11.46 9.76 7.80 6.50 3.94
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.37 26.73 20.83 18.31 15.28 10.91 9.13 6.73 5.12 4.37 - - -
2.5” X 1/4” 39.37 39.37 39.37 31.50 24.53 21.61 17.99 12.83 10.79 7.91 6.06 5.16 4.09 - -
3” X 1/4” 39.37 39.37 39.37 36.10 28.11 24.72 20.63 14.72 12.36 9.06 6.93 5.91 4.72 3.94 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 31.57 27.80 23.15 16.54 13.90 10.20 7.80 6.61 5.28 4.41 -
4” X 1/4” 39.37 39.37 39.37 39.37 34.92 30.75 25.63 18.31 15.35 11.26 8.62 7.32 5.87 4.88 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 38.23 33.62 28.03 20.00 16.81 12.32 9.41 7.99 6.42 5.31 3.98
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 18.23 13.39 10.24 8.70 6.93 5.79 4.21
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.21 32.68 23.35 19.61 14.37 10.98 9.33 7.48 6.22 4.29
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.96 24.96 20.94 15.39 11.77 10.00 7.99 6.65 4.33
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 34.92 27.17 21.18 18.62 15.51 11.06 9.29 6.81 5.20 4.45 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.09 25.00 21.97 18.31 13.07 10.98 8.07 6.14 5.24 4.17 - -
3” X 1/4” 39.37 39.37 39.37 36.77 28.66 25.20 21.02 15.00 12.60 9.25 7.05 5.98 4.80 3.98 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.20 28.35 23.62 16.85 14.17 10.39 7.95 6.73 5.39 4.49 -
4” X 1/4” 39.37 39.37 39.37 39.37 35.67 31.38 26.14 18.66 15.67 11.50 8.78 7.48 5.98 4.96 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.02 34.33 28.62 20.43 17.17 12.60 9.61 8.19 6.54 5.43 4.09
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.24 31.02 22.17 18.62 13.66 10.43 8.86 7.09 5.91 4.41
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.04 14.69 11.22 9.53 7.64 6.34 4.72
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.71 25.51 21.42 15.71 12.01 10.20 8.15 6.81 4.80
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.43 27.56 21.46 18.90 15.75 11.22 9.45 6.93 5.28 4.49 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.56 25.35 22.32 18.58 13.27 11.14 8.19 6.26 5.31 4.25 - -
3” X 1/4” 39.37 39.37 39.37 37.36 29.13 25.63 21.34 15.24 12.80 9.41 7.17 6.10 4.88 4.06 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 32.76 28.82 24.02 17.17 14.41 10.55 8.07 6.85 5.47 4.57 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.30 31.93 26.61 19.02 15.94 11.69 8.94 7.60 6.06 5.08 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.96 29.13 20.79 17.48 12.83 9.80 8.35 6.65 5.55 4.17
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.91 31.61 22.56 18.94 13.90 10.63 9.02 7.20 6.02 4.49
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 20.39 14.96 11.46 9.72 7.80 6.50 4.84
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.38 25.98 21.81 16.02 12.24 10.39 8.31 6.93 5.20
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 35.83 27.87 21.69 19.09 15.91 11.38 9.53 7.01 5.35 4.53 - - -
2.5” X 1/4” 39.37 39.37 39.37 32.95 25.67 22.60 18.82 13.43 11.30 8.27 6.34 5.39 4.29 - -
3” X 1/4” 39.37 39.37 39.37 37.87 29.53 25.98 21.65 15.47 12.99 9.53 7.28 6.18 4.96 4.13 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.23 29.25 24.37 17.40 14.61 10.71 8.19 6.97 5.55 4.65 -
4” X 1/4” 39.37 39.37 39.37 39.37 36.85 32.40 27.01 19.29 16.18 11.89 9.09 7.72 6.18 5.16 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.51 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 4.21
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.54 32.13 22.91 19.25 14.13 10.79 9.17 7.32 6.10 4.57
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.75 15.24 11.65 9.88 7.91 6.57 4.92
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.01 26.42 22.20 16.30 12.44 10.59 8.46 7.05 5.28
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.18 28.15 21.93 19.29 16.06 11.46 9.65 7.09 5.39 4.61 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.35 25.98 22.83 19.06 13.58 11.42 8.39 6.42 5.43 4.33 - -
3” X 1/4” 39.37 39.37 39.37 38.35 29.88 26.30 21.89 15.63 13.15 9.65 7.36 6.26 5.00 4.17 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.66 29.61 24.69 17.60 14.80 10.87 8.31 7.05 5.63 4.69 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.32 32.83 27.36 19.53 16.42 12.05 9.21 7.83 6.26 5.20 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.98 30.00 21.42 17.99 13.19 10.08 8.58 6.85 5.71 4.29
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.09 32.56 23.27 19.53 14.33 10.94 9.33 7.44 6.22 4.65
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.08 25.04 21.06 15.43 11.81 10.04 8.03 6.69 5.00
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.56 26.81 22.52 16.54 12.64 10.75 8.58 7.17 5.35
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 36.50 28.39 22.13 19.45 16.22 11.57 9.72 7.13 5.43 4.65 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.66 26.22 23.07 19.21 13.74 11.54 8.46 6.46 5.47 4.37 - -
3” X 1/4” 39.37 39.37 39.37 38.74 30.20 26.54 22.13 15.79 13.27 9.72 7.44 6.34 5.04 4.21 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.02 29.92 24.96 17.80 14.96 10.98 8.39 7.13 5.71 4.76 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.76 33.23 27.68 19.76 16.61 12.20 9.33 7.91 6.34 5.28 3.94
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.46 30.35 21.69 18.23 13.39 10.24 8.70 6.93 5.79 4.33
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.99 23.54 19.76 14.53 11.10 9.45 7.56 6.30 4.72
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.55 25.39 21.34 15.63 11.97 10.16 8.11 6.77 5.08
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 22.83 16.77 12.80 10.87 8.70 7.24 5.43
CABS144T / CABS144TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 37.24 28.98 22.56 19.84 16.54 11.81 9.92 7.28 5.55 4.72 - - -
2.5” X 1/4” 39.37 39.37 39.37 33.86 26.38 23.23 19.33 13.82 11.61 8.50 6.50 5.51 4.41 - -
3” X 1/4” 39.37 39.37 39.37 38.58 30.08 26.46 22.05 15.75 13.23 9.69 7.40 6.30 5.04 4.21 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 33.66 29.65 24.69 17.64 14.80 10.87 8.31 7.05 5.63 4.69 -
4” X 1/4” 39.37 39.37 39.37 39.37 37.20 32.72 27.28 19.49 16.34 12.01 9.17 7.80 6.22 5.20 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.79 29.80 21.30 17.87 13.11 10.04 8.50 6.81 5.67 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.78 32.32 23.07 19.37 14.21 10.87 9.25 7.40 5.94 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.80 24.84 20.87 15.08 11.69 9.96 7.95 6.10 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.24 26.61 22.36 15.16 12.52 10.67 8.50 6.30 -
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 38.39 29.84 23.27 20.47 17.05 12.17 10.24 7.52 5.75 4.88 - - -
2.5” X 1/4” 39.37 39.37 39.37 34.96 27.20 23.94 19.96 14.25 11.97 8.78 6.69 5.71 4.57 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.06 27.32 22.76 16.26 13.66 10.00 7.64 6.50 5.20 4.33 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 34.76 30.59 25.47 18.19 15.28 11.22 8.58 7.28 5.83 4.84 -
4” X 1/4” 39.37 39.37 39.37 39.37 38.39 33.78 28.15 20.12 16.89 12.40 9.49 8.03 6.42 5.35 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.93 30.75 21.97 18.46 13.54 10.35 8.78 7.05 5.87 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.35 23.82 20.00 14.69 11.22 9.53 7.64 6.34 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.87 25.63 21.54 15.35 12.09 10.28 8.19 6.85 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.39 27.40 23.03 15.43 12.91 10.98 8.78 7.13 4.02
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.29 30.55 23.82 20.94 17.44 12.48 10.47 7.68 5.87 5.00 3.98 - -
2.5” X 1/4” 39.37 39.37 39.37 35.83 27.91 24.57 20.47 14.61 12.28 9.02 6.89 5.83 4.69 - -
3” X 1/4” 39.37 39.37 39.37 39.37 31.85 28.03 23.35 16.65 14.02 10.28 7.83 6.65 5.31 4.45 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 35.67 31.38 26.14 18.66 15.67 11.50 8.78 7.48 5.98 4.96 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.69 28.90 20.63 17.32 12.72 9.72 8.27 6.61 5.51 4.13
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.91 31.57 22.56 18.94 13.90 10.63 9.02 7.20 6.02 4.21
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.21 24.45 20.51 15.08 11.50 9.76 7.83 6.50 4.29
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.81 26.30 22.09 15.67 12.40 10.51 8.43 7.01 4.41
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.11 23.62 15.79 13.27 11.26 9.02 7.52 4.49
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 31.14 24.25 21.34 17.80 12.68 10.67 7.83 5.98 5.08 4.06 - -
2.5” X 1/4” 39.37 39.37 39.37 36.54 28.46 25.04 20.87 14.88 12.52 9.17 7.01 5.94 4.76 3.98 -
3” X 1/4” 39.37 39.37 39.37 39.37 32.52 28.62 23.82 17.01 14.29 10.47 8.03 6.81 5.43 4.53 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 36.46 32.05 26.73 19.09 16.02 11.77 8.98 7.64 6.10 5.08 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.43 29.53 21.10 17.72 12.99 9.92 8.43 6.73 5.63 4.21
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.74 32.28 23.03 19.37 14.21 10.87 9.21 7.36 6.14 4.61
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.96 24.96 20.98 15.39 11.77 10.00 7.99 6.65 4.80
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 22.56 16.57 12.68 10.75 8.62 7.17 4.88
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.74 24.13 17.52 13.54 11.50 9.21 7.68 5.00
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 31.61 24.61 21.65 18.03 12.87 10.83 7.95 6.06 5.16 4.13 - -
2.5” X 1/4” 39.37 39.37 39.37 37.13 28.90 25.43 21.18 15.12 12.72 9.33 7.13 6.06 4.84 4.02 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.07 29.09 24.25 17.32 14.53 10.67 8.15 6.93 5.55 4.61 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 37.09 32.64 27.20 19.41 16.30 11.97 9.13 7.76 6.22 5.16 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.10 30.08 21.46 18.03 13.23 10.12 8.58 6.89 5.71 4.29
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.87 23.46 19.72 14.49 11.06 9.41 7.52 6.26 4.69
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.63 25.47 21.38 15.71 12.01 10.20 8.15 6.77 5.08
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.35 27.40 22.99 16.89 12.91 10.98 8.78 7.32 5.39
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 24.61 18.07 13.82 11.73 9.37 7.83 5.47
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.01 24.92 21.93 18.27 13.03 10.94 8.03 6.14 5.24 4.17 - -
2.5” X 1/4” 39.37 39.37 39.37 37.60 29.29 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.92 4.09 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.54 29.53 24.61 17.56 14.76 10.83 8.27 7.01 5.63 4.69 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 37.64 33.11 27.60 19.72 16.54 12.17 9.29 7.87 6.30 5.24 3.94
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.65 30.55 21.81 18.31 13.43 10.28 8.74 6.97 5.83 4.37
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.86 20.04 14.72 11.26 9.57 7.64 6.38 4.76
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.22 25.87 21.73 15.94 12.20 10.35 8.27 6.89 5.16
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.98 27.83 23.39 17.17 13.11 11.14 8.94 7.44 5.55
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.80 25.04 18.39 14.06 11.93 9.53 7.95 5.94
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.32 25.20 22.17 18.46 13.19 11.06 8.11 6.22 5.28 4.21 - -
2.5” X 1/4” 39.37 39.37 39.37 38.03 29.65 26.06 21.73 15.51 13.03 9.57 7.32 6.22 4.96 4.13 -
3” X 1/4” 39.37 39.37 39.37 39.37 33.94 29.88 24.88 17.76 14.92 10.94 8.39 7.13 5.67 4.72 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.15 33.54 27.95 19.96 16.77 12.32 9.41 7.99 6.38 5.31 3.98
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.13 30.94 22.09 18.54 13.62 10.43 8.86 7.09 5.91 4.41
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.86 24.17 20.31 14.92 11.42 9.69 7.76 6.46 4.84
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.73 26.26 22.05 16.18 12.36 10.51 8.39 7.01 5.24
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.40 13.31 11.30 9.06 7.52 5.63
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.24 25.39 18.66 14.25 12.13 9.69 8.07 6.06
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.64 25.39 22.36 18.62 13.31 11.18 8.19 6.26 5.31 4.25 - -
2.5” X 1/4” 39.37 39.37 39.37 38.43 29.92 26.34 21.93 15.67 13.15 9.65 7.36 6.26 5.00 4.17 -
3” X 1/4” 39.37 39.37 39.37 39.37 34.29 30.20 25.16 17.95 15.08 11.06 8.46 7.20 5.75 4.80 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.54 33.94 28.27 20.20 16.97 12.44 9.53 8.07 6.46 5.39 4.02
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.56 31.30 22.36 18.78 13.78 10.55 8.94 7.17 5.94 4.45
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.29 24.49 20.55 15.08 11.54 9.80 7.83 6.54 4.88
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.20 26.57 22.32 16.38 12.52 10.63 8.50 7.09 5.31
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.62 24.06 17.64 13.50 11.46 9.17 7.64 5.71
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.63 25.75 18.90 14.45 12.28 9.80 8.19 6.14
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 32.87 25.59 22.52 18.78 13.39 11.26 8.27 6.30 5.35 4.29 - -
2.5” X 1/4” 39.37 39.37 39.37 38.74 30.20 26.57 22.13 15.79 13.27 9.72 7.44 6.34 5.04 4.21 -
3” X 1/4” 39.37 39.37 39.37 39.37 34.61 30.47 25.39 18.11 15.24 11.18 8.54 7.24 5.79 4.84 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.94 34.25 28.54 20.39 17.13 12.56 9.61 8.15 6.54 5.43 4.06
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.95 31.61 22.60 18.98 13.94 10.63 9.06 7.24 6.02 4.53
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.65 24.76 20.79 15.28 11.65 9.92 7.91 6.61 4.96
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.85 22.56 16.57 12.68 10.75 8.62 7.17 5.35
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.94 24.29 17.83 13.62 11.57 9.25 7.72 5.79
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.98 26.02 19.09 14.61 12.40 9.92 8.27 6.18
CABS144T / CABS144TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 33.43 26.02 22.91 19.09 13.62 11.46 8.39 6.42 5.47 4.37 - -
2.5” X 1/4” 39.37 39.37 39.37 38.94 30.31 26.69 22.24 15.87 13.35 9.76 7.48 6.34 5.08 4.21 -
3” X 1/4” 39.37 39.37 39.37 39.37 34.45 30.31 25.28 18.03 15.16 11.10 8.50 7.20 5.79 4.80 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 38.50 33.86 28.23 20.16 16.93 12.44 9.49 8.07 6.46 5.35 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.36 31.14 22.24 18.66 13.70 10.47 8.90 7.13 5.51 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.98 24.25 20.39 14.96 11.42 9.72 7.76 5.71 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.81 26.30 22.09 15.00 12.40 10.51 8.43 5.87 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 15.08 13.31 11.34 8.74 6.06 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.24 25.39 15.12 14.21 12.13 9.02 6.26 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 34.49 26.89 23.66 19.69 14.06 11.81 8.66 6.61 5.63 4.49 - -
2.5” X 1/4” 39.37 39.37 39.37 39.37 31.30 27.56 22.95 16.38 13.78 10.12 7.72 6.57 5.24 4.37 -
3” X 1/4” 39.37 39.37 39.37 39.37 35.59 31.30 26.10 18.62 15.63 11.50 8.78 7.44 5.94 4.96 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.96 29.13 20.83 17.48 12.83 9.80 8.35 6.65 5.55 -
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.54 32.13 22.95 19.25 14.13 10.83 9.17 7.36 6.10 -
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.08 25.04 21.02 15.24 11.81 10.04 8.03 6.57 -
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.95 27.09 22.76 15.31 12.76 10.87 8.66 6.73 -
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.13 24.49 15.35 13.74 11.65 9.33 6.93 -
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.14 26.18 15.43 14.41 12.48 9.96 7.09 3.98
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 35.31 27.52 24.21 20.20 14.41 12.09 8.90 6.77 5.75 4.61 - -
2.5” X 1/4” 39.37 39.37 39.37 39.37 32.09 28.27 23.54 16.81 14.13 10.35 7.91 6.73 5.39 4.49 -
3” X 1/4” 39.37 39.37 39.37 39.37 36.50 32.13 26.77 19.13 16.06 11.77 9.02 7.64 6.10 5.08 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 35.91 29.92 21.38 17.95 13.15 10.08 8.54 6.85 5.71 4.06
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 32.99 23.54 19.76 14.53 11.10 9.41 7.52 6.26 4.13
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.98 25.71 21.57 15.55 12.13 10.28 8.23 6.85 4.21
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.94 27.80 23.35 15.59 13.11 11.14 8.90 7.40 4.29
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.88 25.12 15.63 14.09 11.97 9.57 7.80 4.37
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.93 26.85 15.71 14.57 12.80 10.24 7.95 4.49
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 36.02 28.07 24.69 20.55 14.69 12.32 9.06 6.93 5.87 4.69 - -
2.5” X 1/4” 39.37 39.37 39.37 39.37 32.76 28.82 24.02 17.13 14.41 10.55 8.07 6.85 5.47 4.57 -
3” X 1/4” 39.37 39.37 39.37 39.37 37.28 32.80 27.32 19.53 16.38 12.05 9.21 7.80 6.26 5.20 -
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 36.65 30.55 21.81 18.31 13.46 10.28 8.74 6.97 5.83 4.37
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 33.70 24.06 20.20 14.84 11.34 9.65 7.72 6.42 4.65
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 16.18 12.36 10.51 8.43 7.01 4.72
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.43 23.86 16.85 13.39 11.38 9.09 7.60 4.80
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.67 17.13 14.41 12.24 9.76 8.15 4.88
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.64 27.40 17.44 14.76 13.07 10.47 8.70 4.96
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 36.57 28.50 25.08 20.91 14.92 12.52 9.17 7.01 5.98 4.76 3.98 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 33.27 29.29 24.41 17.44 14.65 10.75 8.23 6.97 5.59 4.65 -
3” X 1/4” 39.37 39.37 39.37 39.37 37.91 33.35 27.80 19.84 16.65 12.24 9.37 7.95 6.34 5.28 3.98
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.32 31.10 22.20 18.66 13.70 10.47 8.90 7.13 5.91 4.45
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.29 24.49 20.59 15.12 11.54 9.80 7.83 6.54 4.88
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 37.44 26.73 22.48 16.50 12.60 10.71 8.58 7.13 5.24
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.94 24.33 17.83 13.66 11.57 9.25 7.72 5.31
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 26.14 18.94 14.69 12.48 9.96 8.31 5.39
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.27 27.91 19.21 14.92 13.31 10.67 8.86 5.47
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 37.05 28.86 25.39 21.14 15.12 12.68 9.29 7.13 6.02 4.84 4.02 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 33.74 29.69 24.72 17.68 14.84 10.91 8.31 7.09 5.67 4.72 -
3” X 1/4” 39.37 39.37 39.37 39.37 38.46 33.86 28.19 20.12 16.93 12.40 9.49 8.07 6.46 5.35 4.02
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 37.87 31.57 22.52 18.94 13.90 10.63 9.02 7.20 6.02 4.49
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 34.84 24.88 20.91 15.35 11.73 9.96 7.95 6.65 4.96
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.03 27.17 22.83 16.73 12.80 10.87 8.70 7.24 5.43
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.41 24.69 18.15 13.86 11.77 9.41 7.83 5.83
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.61 26.57 19.49 14.92 12.68 10.12 8.43 5.91
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.82 28.39 20.83 15.12 13.54 10.83 9.02 5.98
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 37.44 29.17 25.67 21.38 15.28 12.83 9.41 7.20 6.10 4.88 4.06 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 34.13 30.04 25.04 17.87 15.00 11.02 8.43 7.17 5.71 4.76 -
3” X 1/4” 39.37 39.37 39.37 39.37 38.94 34.25 28.54 20.39 17.13 12.56 9.61 8.15 6.54 5.43 4.06
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.35 31.97 22.83 19.17 14.06 10.75 9.13 7.32 6.10 4.57
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.28 25.20 21.18 15.55 11.89 10.08 8.07 6.73 5.04
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 38.54 27.52 23.11 16.97 12.99 11.02 8.82 7.36 5.51
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.84 25.04 18.39 14.06 11.93 9.57 7.95 5.94
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.09 26.93 19.76 15.12 12.83 10.28 8.54 6.42
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.29 28.82 21.14 15.31 13.74 10.98 9.13 6.50
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 37.76 29.41 25.91 21.57 15.39 12.95 9.49 7.24 6.18 4.92 4.09 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 34.45 30.31 25.28 18.03 15.16 11.10 8.50 7.20 5.79 4.80 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.33 34.61 28.82 20.59 17.28 12.68 9.69 8.23 6.57 5.47 4.09
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 38.78 32.32 23.07 19.37 14.21 10.87 9.25 7.40 6.14 4.61
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 35.71 25.51 21.42 15.71 12.01 10.20 8.15 6.81 5.08
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.02 27.87 23.39 17.17 13.15 11.14 8.94 7.44 5.55
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.20 25.35 18.62 14.21 12.09 9.69 8.07 6.02
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.48 27.28 20.04 15.31 12.99 10.39 8.66 6.50
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.72 29.17 21.42 15.47 13.90 11.14 9.25 6.93
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 1/4” 39.37 39.37 39.37 38.07 29.65 26.10 21.73 15.51 13.03 9.57 7.32 6.22 4.96 4.13 -
2.5” X 1/4” 39.37 39.37 39.37 39.37 34.76 30.59 25.47 18.19 15.28 11.22 8.58 7.28 5.83 4.84 -
3” X 1/4” 39.37 39.37 39.37 39.37 39.37 34.92 29.09 20.79 17.44 12.80 9.80 8.31 6.65 5.55 4.13
3.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.13 32.64 23.31 19.57 14.37 10.98 9.33 7.44 6.22 4.65
4” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 36.06 25.75 21.61 15.87 12.13 10.31 8.23 6.85 5.16
4.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.15 23.66 17.36 13.27 11.26 9.02 7.52 5.63
5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.51 25.63 18.82 14.37 12.20 9.76 8.15 6.10
5.5” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 27.56 20.24 15.47 13.15 10.51 8.78 6.57
6” X 1/4” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.12 29.49 21.65 15.67 14.06 11.26 9.37 7.01
Data and Calculations are only recommendations and for ERIFLEX’s products only
CABS382T / CABS382TN
Phase-Phase Distance
between axis (d): 3 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 37.64 29.33 25.79 21.50 15.35 12.87 9.45 7.24 6.14 4.65 - -
2.5” X 3/8” 39.37 39.37 39.37 39.37 33.31 29.29 24.41 17.44 14.65 10.75 8.23 6.97 4.80 - -
3” X 3/8” 39.37 39.37 39.37 39.37 37.09 32.64 27.20 19.02 16.30 11.97 9.13 7.76 4.96 - -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.91 29.92 19.13 17.95 13.19 10.08 8.03 5.12 - -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.09 32.60 19.25 18.27 14.33 10.94 8.35 5.31 - -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.20 19.96 18.35 15.51 11.85 8.66 5.55 - -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.80 20.75 18.46 16.65 12.36 8.98 5.75 3.98 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 21.50 18.54 17.32 12.68 9.33 5.94 4.13 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 22.28 18.66 17.36 12.95 9.69 6.18 4.29 -
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 32.44 28.54 23.78 16.97 14.25 10.47 7.99 6.81 5.43 3.94 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 36.65 32.24 26.89 19.21 16.10 11.85 9.06 7.68 5.83 4.02 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.79 29.80 21.30 17.87 13.11 10.04 8.54 5.94 4.13 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.17 32.64 22.09 18.62 14.37 10.98 9.33 6.10 4.25 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.39 22.72 18.70 15.59 11.89 9.84 6.30 4.37 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 23.39 18.78 16.77 12.83 10.12 6.50 4.49 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.09 18.86 17.48 13.62 10.43 6.65 4.65 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.98 18.94 17.52 13.90 10.75 6.89 4.76 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 19.02 17.60 14.17 11.06 7.09 4.92 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.69 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.04 29.17 20.83 17.52 12.83 9.80 8.35 6.65 4.76 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.74 32.28 23.03 18.98 14.21 10.87 9.21 6.97 4.84 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.20 25.16 19.06 15.51 11.85 10.08 7.13 4.92 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 19.13 16.77 12.80 10.87 7.28 5.04 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 19.17 17.68 13.74 11.65 7.44 5.16 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 19.41 17.72 14.65 11.93 7.64 5.28 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 19.88 17.76 15.12 12.20 7.83 5.43 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 20.39 17.80 15.35 12.40 7.99 5.55 -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 37.99 33.43 27.87 19.88 16.69 12.24 9.37 7.95 6.38 5.31 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.60 31.34 22.40 18.78 13.78 10.55 8.98 7.17 5.47 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.39 15.24 11.65 9.88 7.91 5.55 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 20.71 16.57 12.68 10.79 8.15 5.67 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.02 21.10 17.87 13.66 11.61 8.31 5.75 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.06 21.50 17.91 14.65 12.44 8.43 5.87 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 21.89 17.95 15.59 12.99 8.62 5.98 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.00 22.36 17.99 16.34 13.19 8.78 6.10 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 22.80 18.03 16.57 13.35 8.98 6.22 -
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.67 29.72 21.22 17.83 13.07 10.00 8.50 6.77 5.67 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.00 14.69 11.22 9.53 7.64 6.22 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 16.18 12.36 10.51 8.43 6.30 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.54 23.35 17.60 13.46 11.42 9.13 6.38 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.11 14.49 12.32 9.33 6.46 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 27.60 18.15 15.47 13.15 9.45 6.57 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 29.33 18.19 16.46 13.98 9.61 6.65 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 31.02 18.23 17.24 14.13 9.76 6.77 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.90 32.68 18.27 17.28 14.29 9.92 6.89 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.76 31.46 22.48 18.86 13.86 10.59 8.98 7.20 5.98 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.20 21.18 15.55 11.89 10.08 8.07 6.73 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.86 27.76 23.31 17.13 13.07 11.10 8.90 7.01 3.94
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.12 25.31 18.35 14.21 12.09 9.65 7.09 3.98
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.40 27.20 18.39 15.28 12.99 10.35 7.17 4.02
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.57 29.06 18.43 16.30 13.86 10.47 7.28 4.09
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.69 30.83 18.43 17.28 14.69 10.63 7.36 4.13
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.78 32.56 18.46 17.40 15.08 10.79 7.48 4.21
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.25 18.50 17.40 15.24 10.94 7.60 4.25
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.11 23.66 19.88 14.57 11.14 9.49 7.56 6.30 4.29
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.17 26.54 22.28 16.34 12.52 10.63 8.50 7.09 4.33
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 24.49 17.99 13.74 11.69 9.33 7.76 4.37
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.65 26.57 18.58 14.92 12.68 10.12 7.83 4.41
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.98 28.54 18.62 16.02 13.62 10.91 7.91 4.45
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.26 30.43 18.66 17.09 14.53 11.54 7.99 4.49
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 18.70 17.52 15.39 11.65 8.07 4.53
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 18.70 17.52 16.02 11.77 8.19 4.61
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 18.74 17.56 16.14 11.93 8.27 4.65
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.69 24.76 20.83 15.28 11.69 9.92 7.95 6.61 4.72
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 17.13 13.11 11.14 8.90 7.40 4.76
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.63 18.82 14.41 12.24 9.76 8.15 4.76
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 18.86 15.59 13.27 10.59 8.58 4.80
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 29.84 18.86 16.73 14.25 11.38 8.62 4.84
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.87 31.81 18.90 17.64 15.16 12.13 8.70 4.88
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.66 18.94 17.68 16.06 12.52 8.82 4.96
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 18.94 17.68 16.93 12.60 8.90 5.00
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.28 18.98 17.72 17.05 12.68 8.98 5.04
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.22 25.87 21.73 15.94 12.20 10.35 8.27 6.89 5.16
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.98 24.33 17.87 13.66 11.61 9.29 7.72 5.16
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 19.06 15.00 12.76 10.20 8.50 5.20
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.49 28.98 19.09 16.26 13.82 11.06 9.21 5.24
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.01 31.10 19.13 17.44 14.84 11.85 9.37 5.28
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 19.13 17.80 15.79 12.64 9.45 5.31
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.04 19.17 17.80 16.69 13.19 9.53 5.35
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 19.21 17.83 17.28 13.23 9.61 5.39
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.74 19.21 17.83 17.28 13.35 9.69 5.43
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.68 26.89 22.60 16.57 12.68 10.79 8.62 7.17 5.39
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.16 25.31 18.58 14.21 12.09 9.65 8.03 5.59
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 19.72 15.59 13.27 10.59 8.82 5.63
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 19.84 16.89 14.37 11.50 9.57 5.63
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 19.96 17.95 15.39 12.32 10.12 5.67
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.37 20.12 17.95 16.38 13.11 10.20 5.71
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.34 20.24 17.95 17.32 13.82 10.24 5.75
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.27 20.39 17.99 17.40 13.90 10.35 5.79
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 20.59 17.99 17.40 13.98 10.43 5.87
Data and Calculations are only recommendations and for ERIFLEX’s products only
CABS382T / CABS382TN
Phase-Phase Distance
between axis (d): 3 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 37.09 28.90 25.43 21.18 15.12 12.72 9.33 7.13 6.06 4.57 - -
2.5” X 3/8” 39.37 39.37 39.37 39.37 33.58 29.57 24.65 17.60 14.76 10.83 8.27 7.05 4.72 - -
3” X 3/8” 39.37 39.37 39.37 39.37 38.15 33.58 27.99 18.98 16.77 12.32 9.41 7.68 4.88 - -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.52 31.26 19.09 18.15 13.74 10.51 7.95 5.08 - -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.45 19.21 18.23 15.16 11.46 8.27 5.28 - -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 19.80 18.35 16.57 11.89 8.58 5.47 - -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 20.59 18.43 17.24 12.28 8.94 5.71 3.94 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 21.38 18.54 17.28 12.60 9.25 5.91 4.09 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 22.17 18.62 17.36 12.91 9.61 6.14 4.25 -
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 38.90 30.31 26.65 22.20 15.87 13.31 9.76 7.48 6.34 5.08 - -
2.5” X 3/8” 39.37 39.37 39.37 39.37 35.28 31.02 25.87 18.46 15.51 11.38 8.70 7.40 5.75 3.98 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.24 29.33 20.94 17.60 12.91 9.88 8.39 5.91 4.09 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.29 32.76 21.89 18.58 14.41 11.02 9.37 6.06 4.21 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.06 22.52 18.66 15.87 12.13 9.76 6.26 4.33 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.33 23.23 18.74 17.32 13.23 10.08 6.42 4.45 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.39 18.86 17.48 13.58 10.35 6.61 4.61 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 18.94 17.52 13.82 10.71 6.85 4.72 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 19.02 17.56 14.13 11.02 7.05 4.88 -
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 31.42 27.68 23.03 16.46 13.82 10.16 7.76 6.57 5.28 4.37 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 36.61 32.20 26.85 19.17 16.10 11.81 9.02 7.68 6.14 4.72 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.57 30.47 21.77 18.27 13.43 10.24 8.70 6.93 4.80 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 19.02 14.96 11.46 9.72 7.09 4.92 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.44 26.73 19.09 16.50 12.60 10.71 7.24 5.00 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.13 19.17 17.68 13.74 11.57 7.40 5.16 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.50 19.33 17.72 14.84 11.89 7.60 5.28 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.86 19.80 17.76 15.08 12.17 7.80 5.39 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.14 20.31 17.80 15.31 12.40 7.99 5.55 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 32.32 28.46 23.70 16.93 14.21 10.43 7.99 6.77 5.43 4.53 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 37.68 33.15 27.64 19.72 16.57 12.17 9.29 7.91 6.30 5.28 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.68 31.42 22.44 18.82 13.82 10.55 8.98 7.17 5.51 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.04 25.04 20.63 15.43 11.81 10.04 8.03 5.63 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.62 27.56 20.98 17.01 12.99 11.02 8.27 5.71 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.04 21.38 17.91 14.17 12.05 8.43 5.83 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.48 21.81 17.95 15.31 12.95 8.58 5.94 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.88 22.24 17.99 16.30 13.15 8.74 6.06 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 22.72 18.03 16.54 13.31 8.94 6.18 -
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.07 29.09 24.25 17.32 14.53 10.67 8.15 6.93 5.55 4.61 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 38.62 33.98 28.31 20.20 16.97 12.44 9.53 8.11 6.46 5.39 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.62 32.20 22.99 19.29 14.17 10.83 9.21 7.36 6.14 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.94 25.67 21.57 15.83 12.09 10.28 8.23 6.34 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.44 13.35 11.34 9.06 6.42 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.83 25.91 18.15 14.53 12.36 9.41 6.54 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.35 27.99 18.19 15.71 13.35 9.57 6.65 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 30.04 18.23 16.85 14.09 9.72 6.77 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.19 32.09 18.27 17.24 14.25 9.92 6.89 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.70 29.65 24.72 17.64 14.80 10.87 8.31 7.05 5.63 4.69 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 34.65 28.86 20.63 17.32 12.72 9.72 8.27 6.61 5.51 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 32.87 23.46 19.72 14.45 11.06 9.41 7.52 6.26 3.94
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.73 26.22 22.05 16.18 12.36 10.51 8.39 7.01 3.98
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.17 4.02
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.54 26.50 18.39 14.84 12.64 10.12 7.24 4.06
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.09 28.62 18.43 16.06 13.66 10.59 7.36 4.13
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.61 30.75 18.46 17.24 14.65 10.75 7.44 4.17
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.06 32.83 18.50 17.40 15.20 10.91 7.56 4.25
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.24 29.37 20.94 17.60 12.91 9.88 8.39 6.69 5.59 4.17
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 4.33
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.69 22.44 16.46 12.60 10.71 8.54 7.13 4.37
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.45 24.72 18.15 13.90 11.81 9.45 7.87 4.41
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.13 27.01 18.66 15.16 12.87 10.28 7.95 4.49
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.76 29.21 18.66 16.38 13.94 11.14 8.07 4.53
5.5" X 3/8" 1000.00 39.37 39.37 39.37 39.37 39.37 39.37 37.32 31.34 18.70 17.52 14.96 11.77 8.15 4.57
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.46 18.74 17.56 15.98 11.93 8.27 4.65
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.69 30.51 25.43 18.15 15.24 11.18 8.54 7.28 5.83 4.84 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.71 29.76 21.26 17.83 13.11 10.00 8.50 6.81 5.67 4.25
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.94 24.25 20.35 14.96 11.42 9.72 7.76 6.46 4.76
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.99 27.13 22.80 16.73 12.80 10.87 8.70 7.24 4.80
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.96 25.16 18.46 14.09 12.01 9.61 7.99 4.84
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 27.44 18.90 15.39 13.07 10.47 8.70 4.88
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.35 29.69 18.94 16.65 14.17 11.34 8.78 4.92
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.99 31.89 18.94 17.68 15.20 12.17 8.86 5.00
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 18.98 17.72 16.26 12.68 8.98 5.04
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.08 30.87 25.71 18.35 15.43 11.30 8.66 7.36 5.87 4.88 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.14 30.12 21.54 18.07 13.27 10.16 8.62 6.89 5.75 4.29
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.41 24.57 20.63 15.16 11.57 9.84 7.87 6.54 4.92
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.50 27.52 23.11 16.97 12.95 11.02 8.82 7.32 5.24
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 18.74 14.33 12.17 9.72 8.11 5.24
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.15 27.87 19.13 15.63 13.27 10.63 8.86 5.28
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.91 30.16 19.17 16.93 14.37 11.50 9.53 5.35
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.58 32.40 19.17 17.83 15.43 12.36 9.61 5.39
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.61 19.21 17.83 16.50 13.19 9.69 5.43
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.43 31.18 25.98 18.54 15.59 11.42 8.74 7.44 5.94 4.96 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.54 30.43 21.73 18.27 13.39 10.24 8.70 6.97 5.79 4.33
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.76 24.84 20.87 15.31 11.69 9.96 7.95 6.61 4.96
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.98 27.83 23.39 17.17 13.11 11.14 8.90 7.44 5.55
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.98 14.49 12.32 9.84 8.19 5.67
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.58 28.23 20.08 15.83 13.46 10.75 8.98 5.71
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.38 30.55 20.20 17.17 14.57 11.65 9.72 5.75
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.58 28.23 20.08 15.83 13.46 10.75 8.98 5.71
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.09 32.83 20.35 17.99 15.67 12.52 10.31 5.79
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.08 20.55 17.99 16.73 13.39 10.39 5.83
CABS383T / CABS383TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 32.44 28.54 23.78 16.97 14.25 10.47 7.99 6.81 5.43 3.98 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 36.65 32.24 26.89 19.21 16.10 11.85 9.06 7.68 5.87 4.06 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.79 29.80 21.30 17.87 13.11 10.04 8.54 6.02 4.17 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.17 32.64 22.28 18.62 14.37 10.98 9.33 6.18 4.29 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.39 22.91 18.70 15.59 11.89 9.92 6.34 4.41 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.20 18.78 16.77 12.83 10.24 6.54 4.53 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.09 18.90 17.48 13.70 10.55 6.73 4.69 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.98 18.98 17.56 13.98 10.87 6.93 4.80 -
6" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 19.06 17.60 14.25 11.18 7.17 4.96 -
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.72 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.04 29.17 20.83 17.52 12.83 9.80 8.35 6.65 4.80 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.74 32.28 23.03 19.02 14.21 10.87 9.21 7.05 4.88 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.20 25.16 19.09 15.51 11.85 10.08 7.20 5.00 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 19.13 16.77 12.80 10.87 7.36 5.08 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 19.21 17.68 13.74 11.69 7.52 5.20 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 19.61 17.72 14.65 12.05 7.72 5.35 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 20.08 17.80 15.20 12.28 7.87 5.47 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 20.59 17.83 15.47 12.48 8.07 5.63 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 37.99 33.43 27.87 19.88 16.69 12.24 9.37 7.95 6.38 5.31 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.60 31.34 22.40 18.78 13.78 10.55 8.98 7.17 5.55 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.59 15.24 11.65 9.88 7.91 5.63 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 20.91 16.57 12.68 10.79 8.23 5.71 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.02 21.30 17.87 13.66 11.61 8.39 5.79 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.06 21.69 17.95 14.65 12.44 8.50 5.91 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 22.13 17.99 15.59 13.07 8.70 6.02 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.00 22.56 18.03 16.46 13.27 8.86 6.14 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 23.03 18.07 16.69 13.43 9.06 6.30 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.67 29.72 21.22 17.83 13.07 10.00 8.50 6.77 5.67 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.00 14.69 11.22 9.53 7.64 6.26 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 16.18 12.36 10.51 8.43 6.34 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.54 23.98 17.60 13.46 11.42 9.13 6.42 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.15 14.49 12.32 9.41 6.54 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 27.60 18.19 15.47 13.15 9.53 6.61 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 29.33 18.23 16.46 13.98 9.69 6.73 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 31.02 18.27 17.24 14.21 9.88 6.85 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.90 32.68 18.31 17.28 14.37 10.04 6.97 -
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.76 31.46 22.48 18.86 13.86 10.59 8.98 7.20 5.98 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.20 21.18 15.55 11.89 10.08 8.07 6.73 3.94
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.86 27.76 23.31 17.13 13.07 11.10 8.90 7.09 3.98
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.12 25.31 18.39 14.21 12.09 9.65 7.17 4.02
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.40 27.20 18.39 15.28 12.99 10.39 7.24 4.06
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.57 29.06 18.43 16.30 13.86 10.59 7.32 4.13
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.69 30.83 18.46 17.28 14.69 10.71 7.44 4.17
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.78 32.56 18.50 17.40 15.16 10.87 7.56 4.25
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.25 18.54 17.44 15.31 11.02 7.68 4.29
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.11 23.66 19.88 14.57 11.14 9.49 7.56 6.30 4.33
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.17 26.54 22.28 16.34 12.52 10.63 8.50 7.09 4.37
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 24.49 17.99 13.74 11.69 9.33 7.80 4.41
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.65 26.57 18.62 14.92 12.68 10.12 7.91 4.45
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.98 28.54 18.66 16.02 13.62 10.91 7.99 4.49
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.26 30.43 18.66 17.09 14.53 11.61 8.07 4.53
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 18.70 17.52 15.39 11.77 8.15 4.57
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 18.74 17.56 16.10 11.89 8.27 4.65
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 18.78 17.56 16.26 12.05 8.35 4.69
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.69 24.76 20.83 15.28 11.69 9.92 7.95 6.61 4.76
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 17.13 13.11 11.14 8.90 7.40 4.80
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.63 18.82 14.41 12.24 9.76 8.15 4.80
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 18.86 15.59 13.27 10.59 8.66 4.84
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 29.84 18.90 16.73 14.25 11.38 8.74 4.88
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.87 31.81 18.94 17.68 15.16 12.13 8.82 4.96
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.66 18.94 17.68 16.06 12.60 8.90 5.00
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 18.98 17.72 16.93 12.68 8.98 5.04
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.28 19.02 17.72 17.17 12.76 9.09 5.08
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.22 25.87 21.73 15.94 12.20 10.35 8.27 6.89 5.16
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.98 24.33 17.87 13.66 11.61 9.29 7.72 5.24
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 19.09 15.00 12.76 10.20 8.50 5.24
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.49 28.98 19.13 16.26 13.82 11.06 9.21 5.28
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.01 31.10 19.13 17.44 14.84 11.85 9.45 5.31
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 19.17 17.83 15.79 12.64 9.53 5.35
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.04 19.21 17.83 16.69 13.27 9.61 5.39
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 19.21 17.83 17.28 13.35 9.69 5.43
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.74 19.33 17.87 17.28 13.43 9.80 5.51
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.68 26.89 22.60 16.57 12.68 10.79 8.62 7.17 5.39
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.16 25.31 18.58 14.21 12.09 9.65 8.03 5.63
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 19.92 15.59 13.27 10.59 8.82 5.67
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 20.04 16.89 14.37 11.50 9.57 5.71
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 20.16 17.95 15.39 12.32 10.20 5.75
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.37 20.28 17.95 16.38 13.11 10.28 5.79
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.34 20.43 17.99 17.32 13.86 10.35 5.83
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.27 20.59 17.99 17.40 13.98 10.43 5.87
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 20.79 18.03 17.40 14.06 10.51 5.91
CABS383T / CABS383TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 38.90 30.31 26.65 22.20 15.87 13.31 9.76 7.48 6.34 5.08 4.21 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 35.28 31.02 25.87 18.46 15.51 11.38 8.70 7.40 5.91 4.41 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.24 29.33 20.94 17.60 12.91 9.88 8.39 6.54 4.53 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.29 32.76 23.39 18.86 14.41 11.02 9.37 6.69 4.65 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.06 25.75 18.94 15.87 12.13 10.31 6.89 4.80 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.33 28.11 19.06 17.32 13.23 11.10 7.13 4.92 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.39 19.13 17.64 14.33 11.46 7.32 5.08 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 19.21 17.72 14.76 11.81 7.56 5.24 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 19.80 17.76 15.08 12.17 7.80 5.39 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 31.42 27.68 23.03 16.46 13.82 10.16 7.76 6.57 5.28 4.37 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 36.61 32.20 26.85 19.17 16.10 11.81 9.02 7.68 6.14 5.12 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.57 30.47 21.77 18.27 13.43 10.24 8.70 6.97 5.31 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 19.88 14.96 11.46 9.72 7.76 5.43 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.44 26.73 20.35 16.50 12.60 10.71 7.99 5.55 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.13 20.83 17.87 13.74 11.65 8.19 5.67 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.50 21.34 17.91 14.84 12.64 8.39 5.83 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.86 21.89 17.95 15.94 12.99 8.58 5.98 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.14 22.44 17.99 16.38 13.19 8.82 6.10 -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 32.32 28.46 23.70 16.93 14.21 10.43 7.99 6.77 5.43 4.53 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 37.68 33.15 27.64 19.72 16.57 12.17 9.29 7.91 6.30 5.28 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.68 31.42 22.44 18.82 13.82 10.55 8.98 7.17 5.98 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.04 25.04 21.02 15.43 11.81 10.04 8.03 6.22 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.62 27.56 23.15 17.01 12.99 11.02 8.82 6.34 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.04 25.24 18.11 14.17 12.05 9.29 6.46 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.48 27.28 18.15 15.31 12.99 9.49 6.57 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.88 29.29 18.23 16.46 13.98 9.69 6.69 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 31.26 18.27 17.24 14.21 9.88 6.85 -
Phase-Phase Distance
between axis (d): 6.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.07 29.09 24.25 17.32 14.53 10.67 8.15 6.93 5.55 4.61 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 38.62 33.98 28.31 20.20 16.97 12.44 9.53 8.11 6.46 5.39 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.62 32.20 22.99 19.29 14.17 10.83 9.21 7.36 6.14 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.94 25.67 21.57 15.83 12.09 10.28 8.23 6.85 3.94
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.44 13.35 11.34 9.06 7.13 3.98
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.83 25.91 18.39 14.53 12.36 9.88 7.20 4.06
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.35 27.99 18.43 15.71 13.35 10.59 7.32 4.13
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 30.04 18.46 16.85 14.33 10.75 7.48 4.17
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.19 32.09 18.50 17.40 15.24 10.94 7.60 4.25
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.70 29.65 24.72 17.64 14.80 10.87 8.31 7.05 5.63 4.69 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 34.65 28.86 20.63 17.32 12.72 9.72 8.27 6.61 5.51 4.13
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 32.87 23.46 19.72 14.45 11.06 9.41 7.52 6.26 4.33
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.73 26.22 22.05 16.18 12.36 10.51 8.39 7.01 4.37
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.72 4.45
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.54 26.50 18.66 14.84 12.64 10.12 7.99 4.49
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.09 28.62 18.70 16.06 13.66 10.91 8.11 4.57
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.61 30.75 18.74 17.24 14.65 11.73 8.23 4.61
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.06 32.83 18.78 17.56 15.67 12.05 8.35 4.69
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.24 29.37 20.94 17.60 12.91 9.88 8.39 6.69 5.59 4.17
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 4.76
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.69 22.44 16.46 12.60 10.71 8.54 7.13 4.84
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.45 24.72 18.15 13.90 11.81 9.45 7.87 4.88
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.13 27.01 18.94 15.16 12.87 10.28 8.58 4.96
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.76 29.21 18.98 16.38 13.94 11.14 8.90 5.00
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.32 31.34 19.02 17.60 14.96 11.97 9.02 5.08
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.46 19.02 17.72 15.98 12.76 9.13 5.12
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.69 30.51 25.43 18.15 15.24 11.18 8.54 7.28 5.83 4.84 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.71 29.76 21.26 17.83 13.11 10.00 8.50 6.81 5.67 4.25
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.94 24.25 20.35 14.96 11.42 9.72 7.76 6.46 4.84
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.99 27.13 22.80 16.73 12.80 10.87 8.70 7.24 5.31
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.96 25.16 18.46 14.09 12.01 9.61 7.99 5.35
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 27.44 19.17 15.39 13.07 10.47 8.70 5.39
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.35 29.69 19.21 16.65 14.17 11.34 9.45 5.43
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.99 31.89 19.37 17.87 15.20 12.17 9.80 5.51
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 19.57 17.91 16.26 12.99 9.92 5.55
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.08 30.87 25.71 18.35 15.43 11.30 8.66 7.36 5.87 4.88 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.14 30.12 21.54 18.07 13.27 10.16 8.62 6.89 5.75 4.29
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.41 24.57 20.63 15.16 11.57 9.84 7.87 6.54 4.92
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.50 27.52 23.11 16.97 12.95 11.02 8.82 7.32 5.51
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 18.74 14.33 12.17 9.72 8.11 5.79
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.15 27.87 20.43 15.63 13.27 10.63 8.86 5.87
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.91 30.16 20.75 16.93 14.37 11.50 9.57 5.91
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.58 32.40 20.94 18.03 15.43 12.36 10.28 5.94
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.61 21.14 18.07 16.50 13.19 10.71 6.02
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.43 31.18 25.98 18.54 15.59 11.42 8.74 7.44 5.94 4.96 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.54 30.43 21.73 18.27 13.39 10.24 8.70 6.97 5.79 4.33
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.76 24.84 20.87 15.31 11.69 9.96 7.95 6.61 4.96
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.98 27.83 23.39 17.17 13.11 11.14 8.90 7.44 5.55
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.98 14.49 12.32 9.84 8.19 6.14
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.58 28.23 20.71 15.83 13.46 10.75 8.98 6.30
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.38 30.55 22.32 17.17 14.57 11.65 9.72 6.34
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.09 32.83 22.52 18.19 15.67 12.52 10.43 6.42
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.08 22.72 18.23 16.73 13.39 11.14 6.46
CABS383T / CABS383TN
Phase-Phase Distance
between axis (d): 3.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.87 31.57 26.30 18.78 15.79 11.57 8.86 7.52 6.02 4.57 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.57 30.47 21.77 18.27 13.43 10.24 8.70 6.77 4.69 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.49 24.65 18.98 15.20 11.61 9.88 6.97 4.80 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.43 27.44 19.06 16.93 12.91 10.98 7.17 4.96 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.20 19.17 17.68 14.21 11.54 7.40 5.12 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.91 19.41 17.72 14.88 11.93 7.64 5.28 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.55 20.00 17.80 15.20 12.28 7.87 5.47 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.23 20.67 17.83 15.51 12.52 8.11 5.63 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 21.30 17.91 15.83 12.76 8.39 5.83 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 4.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 37.20 32.72 27.28 19.49 16.34 12.01 9.17 7.80 6.22 5.20 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.91 31.61 22.56 18.94 13.90 10.63 9.06 7.24 5.59 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.79 25.55 20.87 15.75 12.05 10.24 8.19 5.67 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.43 21.34 17.52 13.39 11.38 8.39 5.83 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.26 21.85 17.95 14.72 12.52 8.58 5.94 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 22.36 17.99 16.06 13.19 8.78 6.10 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.77 22.95 18.07 16.65 13.43 9.02 6.26 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 23.54 18.11 16.93 13.62 9.25 6.42 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.39 18.19 17.20 13.86 9.49 6.57 -
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 38.23 33.66 28.03 20.04 16.81 12.32 9.45 8.03 6.42 5.35 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.02 32.52 23.23 19.49 14.33 10.94 9.29 7.44 6.18 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.81 26.30 22.09 16.22 12.40 10.51 8.43 6.57 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.25 24.57 18.03 13.78 11.73 9.37 6.69 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.17 27.01 18.23 15.16 12.87 9.80 6.81 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.04 29.41 18.31 16.50 14.02 10.00 6.93 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 31.77 18.35 17.32 14.53 10.20 7.09 3.98
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.09 18.39 17.32 14.72 10.43 7.24 4.06
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.38 18.46 17.36 14.96 10.63 7.40 4.13
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.09 34.41 28.66 20.47 17.20 12.60 9.65 8.19 6.54 5.47 4.09
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.27 23.74 19.96 14.65 11.18 9.53 7.60 6.34 4.13
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.68 26.89 22.60 16.57 12.68 10.79 8.62 7.17 4.17
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.96 25.16 18.46 14.13 12.01 9.61 7.56 4.25
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.95 27.68 18.54 15.55 13.19 10.55 7.68 4.29
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 18.58 16.93 14.37 11.22 7.80 4.37
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.74 32.56 18.62 17.48 15.51 11.42 7.91 4.45
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 18.66 17.52 15.83 11.61 8.07 4.53
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 18.74 17.56 16.02 11.81 8.19 4.61
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.00 29.17 20.83 17.48 12.83 9.80 8.35 6.65 5.55 4.17
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.90 24.21 20.31 14.92 11.42 9.69 7.76 6.46 4.65
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.43 27.44 23.03 16.93 12.91 10.98 8.78 7.32 4.69
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.67 18.82 14.41 12.24 9.80 8.15 4.72
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.62 28.23 18.82 15.87 13.46 10.79 8.54 4.80
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.61 30.75 18.86 17.24 14.69 11.73 8.66 4.84
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.23 18.90 17.68 15.83 12.48 8.78 4.92
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.63 18.98 17.68 16.93 12.60 8.90 5.00
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.03 19.02 17.72 17.13 12.72 9.06 5.08
Phase-Phase Distance
between axis (d): 7.50 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.51 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 4.21
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.41 24.57 20.63 15.16 11.57 9.84 7.87 6.54 4.92
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.06 27.87 23.43 17.20 13.15 11.18 8.94 7.44 5.20
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 26.10 19.09 14.65 12.44 9.96 8.31 5.24
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.21 28.74 19.13 16.14 13.70 10.94 9.13 5.28
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 31.30 19.17 17.56 14.92 11.93 9.53 5.35
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.82 19.21 17.83 16.14 12.91 9.65 5.39
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.30 19.25 17.87 17.28 13.39 9.76 5.47
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.70 19.49 17.87 17.32 13.50 9.88 5.55
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.98 29.96 21.42 17.99 13.19 10.08 8.58 6.85 5.71 4.29
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.88 24.88 20.91 15.35 11.73 9.96 7.95 6.65 4.96
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.44 13.31 11.34 9.06 7.56 5.67
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.54 26.50 19.45 14.88 12.64 10.12 8.43 5.75
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.72 29.17 20.31 16.38 13.90 11.14 9.25 5.79
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 31.77 20.51 17.83 15.16 12.13 10.08 5.83
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.33 20.71 18.03 16.38 13.11 10.51 5.91
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.85 20.94 18.03 17.44 14.06 10.59 5.94
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.33 21.18 18.07 17.44 14.25 10.75 6.02
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.00 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.34 30.28 21.61 18.15 13.35 10.20 8.66 6.93 5.75 4.33
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.28 25.20 21.14 15.51 11.85 10.08 8.07 6.73 5.04
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.62 24.02 17.64 13.46 11.46 9.17 7.64 5.71
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.93 26.81 19.69 15.04 12.80 10.24 8.50 6.22
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.16 29.53 21.69 16.57 14.09 11.26 9.37 6.30
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.35 32.20 22.24 18.07 15.35 12.28 10.24 6.34
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.80 22.44 18.19 16.61 13.27 11.06 6.38
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.36 22.64 18.23 17.56 14.25 11.46 6.46
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 22.87 18.23 17.56 14.96 11.57 6.50
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.69 30.55 21.81 18.35 13.46 10.28 8.74 6.97 5.83 4.37
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.59 25.43 21.34 15.67 11.97 10.20 8.15 6.77 5.08
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.72 5.79
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.28 27.13 19.88 15.20 12.91 10.35 8.62 6.46
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.55 29.88 21.93 16.77 14.25 11.38 9.49 6.77
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.78 32.56 23.90 18.27 15.55 12.44 10.35 6.85
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.24 25.87 18.39 16.81 13.43 11.18 6.89
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 27.76 18.39 17.68 14.45 12.01 6.93
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.65 18.43 17.72 15.39 12.36 7.01
CABS384T / CABS384TN
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.31 31.06 25.91 18.50 15.51 11.38 8.70 7.40 5.91 4.92 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.04 29.17 20.83 17.52 12.83 9.80 8.35 6.65 5.24 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.74 32.28 23.03 19.37 14.21 10.87 9.21 7.36 5.35 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.20 25.16 20.04 15.51 11.85 10.08 7.87 5.47 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.07 27.17 20.47 16.77 12.80 10.87 8.03 5.59 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 20.94 17.87 13.74 11.69 8.23 5.71 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 21.46 17.91 14.65 12.44 8.43 5.87 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 21.97 17.95 15.55 13.03 8.62 5.98 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 22.52 18.03 16.42 13.23 8.86 6.14 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 37.99 33.43 27.87 19.88 16.69 12.24 9.37 7.95 6.38 5.31 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.60 31.34 22.40 18.78 13.78 10.55 8.98 7.17 5.98 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.57 24.69 20.75 15.24 11.65 9.88 7.91 6.14 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 22.60 16.57 12.68 10.79 8.62 6.26 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.02 23.31 17.87 13.66 11.61 9.17 6.34 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.06 26.06 18.15 14.65 12.44 9.33 6.46 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.03 27.76 18.19 15.59 13.23 9.53 6.61 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.00 29.41 18.23 16.50 14.02 9.72 6.73 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 31.02 18.27 17.24 14.25 9.92 6.89 -
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.67 29.72 21.22 17.83 13.07 10.00 8.50 6.77 5.67 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.00 14.69 11.22 9.53 7.64 6.34 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.77 26.26 22.05 16.18 12.36 10.51 8.43 6.97 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.54 23.98 17.60 13.46 11.42 9.13 7.05 3.94
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.35 14.49 12.32 9.84 7.13 4.02
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.83 27.60 18.39 15.47 13.15 10.43 7.24 4.06
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 29.33 18.43 16.46 13.98 10.63 7.36 4.13
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 31.02 18.46 17.40 14.80 10.79 7.48 4.21
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.90 32.68 18.54 17.40 15.28 10.98 7.64 4.29
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.76 31.46 22.48 18.86 13.86 10.59 8.98 7.20 5.98 4.29
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.31 25.20 21.18 15.55 11.89 10.08 8.07 6.73 4.33
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.86 27.76 23.31 17.13 13.07 11.10 8.90 7.40 4.37
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.12 25.31 18.58 14.21 12.09 9.65 7.83 4.41
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.40 27.20 18.62 15.28 12.99 10.39 7.95 4.45
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.57 29.06 18.66 16.30 13.86 11.06 8.03 4.53
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.69 30.83 18.70 17.28 14.69 11.73 8.15 4.57
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.57 29.06 18.66 16.30 13.86 11.06 8.03 4.53
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.25 18.78 17.56 16.26 12.09 8.39 4.72
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.11 23.66 19.88 14.57 11.14 9.49 7.56 6.30 4.72
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.17 26.54 22.28 16.34 12.52 10.63 8.50 7.09 4.76
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.17 24.49 17.99 13.74 11.69 9.33 7.80 4.80
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.65 26.57 18.86 14.92 12.68 10.12 8.43 4.84
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.98 28.54 18.90 16.02 13.62 10.91 8.74 4.92
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.26 30.43 18.94 17.09 14.53 11.61 8.82 4.96
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 18.98 17.68 15.39 12.32 8.94 5.00
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 19.02 17.72 16.26 12.72 9.06 5.08
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 19.06 17.76 17.09 12.83 9.17 5.16
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.69 24.76 20.83 15.28 11.69 9.92 7.95 6.61 4.96
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.90 27.80 23.35 17.13 13.11 11.14 8.90 7.40 5.24
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.63 18.82 14.41 12.24 9.76 8.15 5.28
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 19.13 15.59 13.27 10.59 8.82 5.31
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 29.84 19.17 16.73 14.25 11.38 9.49 5.35
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.87 31.81 19.21 17.83 15.16 12.13 9.65 5.39
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.66 19.21 17.87 16.06 12.83 9.72 5.47
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.51 19.41 17.87 16.93 13.43 9.84 5.51
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.28 19.61 17.91 17.32 13.54 9.92 5.59
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.22 25.87 21.73 15.94 12.20 10.35 8.27 6.89 5.16
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.98 24.33 17.87 13.66 11.61 9.29 7.72 5.71
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.85 26.73 19.65 15.00 12.76 10.20 8.50 5.75
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.49 28.98 20.31 16.26 13.82 11.06 9.21 5.79
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.01 31.10 20.43 17.44 14.84 11.85 9.88 5.83
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 20.59 17.99 15.79 12.64 10.43 5.87
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.04 20.79 18.03 16.69 13.35 10.51 5.91
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 20.98 18.03 17.44 14.09 10.63 5.98
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.74 21.18 18.07 17.44 14.21 10.71 6.02
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.68 26.89 22.60 16.57 12.68 10.79 8.62 7.17 5.39
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.16 25.31 18.58 14.21 12.09 9.65 8.03 6.02
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.11 27.80 20.39 15.59 13.27 10.59 8.82 6.22
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 21.93 16.89 14.37 11.50 9.57 6.22
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.43 32.28 22.05 18.11 15.39 12.32 10.28 6.26
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.37 22.20 18.15 16.38 13.11 10.91 6.34
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.34 22.36 18.19 17.32 13.86 11.34 6.38
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.27 22.56 18.19 17.56 14.61 11.42 6.42
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 22.72 18.23 17.56 14.92 11.54 6.46
CABS384T / CABS384TN
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 31.42 27.68 23.03 16.46 13.82 10.16 7.76 6.57 5.28 4.37 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 36.61 32.20 26.85 19.17 16.10 11.81 9.02 7.68 6.14 5.12 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.57 30.47 21.77 18.27 13.43 10.24 8.70 6.97 5.71 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 20.39 14.96 11.46 9.72 7.76 5.83 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.44 26.73 21.93 16.50 12.60 10.71 8.54 5.98 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.13 22.44 17.95 13.74 11.65 8.82 6.10 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.50 22.99 18.07 14.84 12.64 9.06 6.26 -
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.86 28.43 18.11 15.94 13.54 9.25 6.42 -
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.14 30.35 18.19 17.05 13.86 9.49 6.57 -
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 32.32 28.46 23.70 16.93 14.21 10.43 7.99 6.77 5.43 4.53 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 37.68 33.15 27.64 19.72 16.57 12.17 9.29 7.91 6.30 5.28 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.68 31.42 22.44 18.82 13.82 10.55 8.98 7.17 5.98 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.04 25.04 21.02 15.43 11.81 10.04 8.03 6.69 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.62 27.56 23.15 17.01 12.99 11.02 8.82 6.81 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.04 25.24 18.31 14.17 12.05 9.61 6.93 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.48 27.28 18.35 15.31 12.99 10.20 7.09 3.98
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.88 29.29 18.39 16.46 13.98 10.43 7.24 4.06
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 31.26 18.46 17.36 14.92 10.63 7.40 4.13
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.07 29.09 24.25 17.32 14.53 10.67 8.15 6.93 5.55 4.61 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 38.62 33.98 28.31 20.20 16.97 12.44 9.53 8.11 6.46 5.39 4.06
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 38.62 32.20 22.99 19.29 14.17 10.83 9.21 7.36 6.14 4.17
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.94 25.67 21.57 15.83 12.09 10.28 8.23 6.85 4.25
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.44 13.35 11.34 9.06 7.56 4.29
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.83 25.91 18.58 14.53 12.36 9.88 7.80 4.37
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.35 27.99 18.62 15.71 13.35 10.67 7.91 4.45
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.79 30.04 18.66 16.85 14.33 11.46 8.03 4.53
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.19 32.09 18.70 17.52 15.31 11.81 8.19 4.61
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 33.70 29.65 24.72 17.64 14.80 10.87 8.31 7.05 5.63 4.69 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 34.65 28.86 20.63 17.32 12.72 9.72 8.27 6.61 5.51 4.13
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 32.87 23.46 19.72 14.45 11.06 9.41 7.52 6.26 4.69
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.73 26.22 22.05 16.18 12.36 10.51 8.39 7.01 4.72
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.72 4.80
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.54 26.50 18.86 14.84 12.64 10.12 8.43 4.84
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.09 28.62 18.90 16.06 13.66 10.91 8.74 4.92
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.61 30.75 18.94 17.24 14.65 11.73 8.90 5.00
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.06 32.83 18.98 17.72 15.67 12.52 9.02 5.08
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.21 30.12 25.08 17.91 15.04 11.06 8.43 7.17 5.75 4.76 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.24 29.37 20.94 17.60 12.91 9.88 8.39 6.69 5.59 4.17
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.43 23.90 20.04 14.72 11.26 9.57 7.64 6.38 4.76
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.40 26.69 22.44 16.46 12.60 10.71 8.54 7.13 5.24
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.45 24.72 18.15 13.90 11.81 9.45 7.87 5.28
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.13 27.01 19.17 15.16 12.87 10.28 8.58 5.31
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.76 29.21 19.17 16.38 13.94 11.14 9.29 5.39
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.32 31.34 19.21 17.60 14.96 11.97 9.72 5.47
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.46 19.45 17.87 15.98 12.76 9.84 5.51
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 34.69 30.51 25.43 18.15 15.24 11.18 8.54 7.28 5.83 4.84 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.71 29.76 21.26 17.83 13.11 10.00 8.50 6.81 5.67 4.25
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.94 24.25 20.35 14.96 11.42 9.72 7.76 6.46 4.84
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.99 27.13 22.80 16.73 12.80 10.87 8.70 7.24 5.43
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.96 25.16 18.46 14.09 12.01 9.61 7.99 5.75
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 27.44 20.16 15.39 13.07 10.47 8.70 5.83
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.35 29.69 20.63 16.65 14.17 11.34 9.45 5.87
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.99 31.89 20.87 17.91 15.20 12.17 10.12 5.94
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 21.10 18.07 16.26 12.99 10.67 5.98
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.08 30.87 25.71 18.35 15.43 11.30 8.66 7.36 5.87 4.88 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.14 30.12 21.54 18.07 13.27 10.16 8.62 6.89 5.75 4.29
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.41 24.57 20.63 15.16 11.57 9.84 7.87 6.54 4.92
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.50 27.52 23.11 16.97 12.95 11.02 8.82 7.32 5.51
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.35 25.51 18.74 14.33 12.17 9.72 8.11 6.06
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.15 27.87 20.43 15.63 13.27 10.63 8.86 6.30
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.91 30.16 22.13 16.93 14.37 11.50 9.57 6.38
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.58 32.40 22.56 18.19 15.43 12.36 10.28 6.42
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.61 22.76 18.23 16.50 13.19 10.98 6.50
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 35.43 31.18 25.98 18.54 15.59 11.42 8.74 7.44 5.94 4.96 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.54 30.43 21.73 18.27 13.39 10.24 8.70 6.97 5.79 4.33
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.76 24.84 20.87 15.31 11.69 9.96 7.95 6.61 4.96
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.98 27.83 23.39 17.17 13.11 11.14 8.90 7.44 5.55
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.75 25.83 18.98 14.49 12.32 9.84 8.19 6.14
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.58 28.23 20.71 15.83 13.46 10.75 8.98 6.73
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.38 30.55 22.44 17.17 14.57 11.65 9.72 6.85
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.09 32.83 24.09 18.39 15.67 12.52 10.43 6.89
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.08 25.75 18.39 16.73 13.39 11.14 6.97
CABS384T / CABS384TN
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 37.20 32.72 27.28 19.49 16.34 12.01 9.17 7.80 6.22 5.20 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.91 31.61 22.56 18.94 13.90 10.63 9.06 7.24 6.02 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.79 25.55 21.46 15.75 12.05 10.24 8.19 6.54 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.43 23.90 17.52 13.39 11.38 9.09 6.65 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.26 26.26 18.27 14.72 12.52 9.84 6.85 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.06 28.58 18.31 16.06 13.62 10.08 7.01 3.94
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.77 30.91 18.39 17.32 14.69 10.35 7.17 4.02
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.15 18.43 17.36 14.92 10.63 7.36 4.13
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.39 18.50 17.40 15.20 10.91 7.56 4.25
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 38.23 33.66 28.03 20.04 16.81 12.32 9.45 8.03 6.42 5.35 4.02
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.02 32.52 23.23 19.49 14.33 10.94 9.29 7.44 6.18 4.17
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.81 26.30 22.09 16.22 12.40 10.51 8.43 7.01 4.21
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.25 24.57 18.03 13.78 11.73 9.37 7.68 4.29
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.17 27.01 18.58 15.16 12.87 10.31 7.80 4.37
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.04 29.41 18.62 16.50 14.02 11.22 7.95 4.49
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 31.77 18.70 17.52 15.16 11.69 8.11 4.57
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.09 18.74 17.56 16.14 11.97 8.31 4.65
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.38 18.82 17.60 16.38 12.20 8.46 4.76
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.09 34.41 28.66 20.47 17.20 12.60 9.65 8.19 6.54 5.47 4.09
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.27 23.74 19.96 14.65 11.18 9.53 7.60 6.34 4.72
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.68 26.89 22.60 16.57 12.68 10.79 8.62 7.17 4.80
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.96 25.16 18.46 14.13 12.01 9.61 7.99 4.88
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.95 27.68 18.94 15.55 13.19 10.55 8.78 4.92
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 18.98 16.93 14.37 11.50 8.94 5.00
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.74 32.56 19.02 17.72 15.51 12.40 9.09 5.12
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.92 19.06 17.76 16.65 12.91 9.25 5.20
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 19.13 17.80 17.24 13.07 9.41 5.28
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.00 29.17 20.83 17.48 12.83 9.80 8.35 6.65 5.55 4.17
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.90 24.21 20.31 14.92 11.42 9.69 7.76 6.46 4.84
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.43 27.44 23.03 16.93 12.91 10.98 8.78 7.32 5.39
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.55 25.67 18.86 14.41 12.24 9.80 8.15 5.43
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.62 28.23 19.33 15.87 13.46 10.79 8.98 5.51
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.61 30.75 19.61 17.24 14.69 11.73 9.76 5.59
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.23 19.88 17.91 15.83 12.68 10.08 5.67
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.63 20.16 17.95 17.01 13.58 10.20 5.75
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.03 20.47 17.99 17.40 13.90 10.35 5.83
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.51 29.61 21.14 17.76 13.03 9.96 8.46 6.77 5.63 4.21
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.41 24.57 20.63 15.16 11.57 9.84 7.87 6.54 4.92
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.06 27.87 23.43 17.20 13.15 11.18 8.94 7.44 5.59
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.10 26.10 19.17 14.65 12.44 9.96 8.31 6.02
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.21 28.74 21.10 16.14 13.70 10.94 9.13 6.06
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 31.30 21.54 17.56 14.92 11.93 9.96 6.14
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.82 21.81 18.11 16.14 12.91 10.75 6.22
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.30 22.09 18.15 17.32 13.86 11.18 6.30
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.70 22.36 18.19 17.52 14.76 11.34 6.38
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 35.98 29.96 21.42 17.99 13.19 10.08 8.58 6.85 5.71 4.29
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.88 24.88 20.91 15.35 11.73 9.96 7.95 6.65 4.96
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.27 23.74 17.44 13.31 11.34 9.06 7.56 5.67
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.54 26.50 19.45 14.88 12.64 10.12 8.43 6.30
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.72 29.17 21.42 16.38 13.90 11.14 9.25 6.65
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 31.77 23.31 17.83 15.16 12.13 10.08 6.69
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.33 25.20 18.31 16.38 13.11 10.91 6.77
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.85 27.05 18.35 17.60 14.06 11.73 6.85
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.33 28.86 18.39 17.68 15.00 12.28 6.93
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.34 30.28 21.61 18.15 13.35 10.20 8.66 6.93 5.75 4.33
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.28 25.20 21.14 15.51 11.85 10.08 8.07 6.73 5.04
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.62 24.02 17.64 13.46 11.46 9.17 7.64 5.71
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.93 26.81 19.69 15.04 12.80 10.24 8.50 6.38
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.16 29.53 21.69 16.57 14.09 11.26 9.37 7.05
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.35 32.20 23.62 18.07 15.35 12.28 10.24 7.28
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.80 25.55 18.54 16.61 13.27 11.06 7.32
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.36 27.44 18.54 17.80 14.25 11.89 7.40
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.29 18.58 17.83 15.24 12.68 7.48
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 36.69 30.55 21.81 18.35 13.46 10.28 8.74 6.97 5.83 4.37
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.59 25.43 21.34 15.67 11.97 10.20 8.15 6.77 5.08
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.72 5.79
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.28 27.13 19.88 15.20 12.91 10.35 8.62 6.46
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.55 29.88 21.93 16.77 14.25 11.38 9.49 7.13
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.78 32.56 23.90 18.27 15.55 12.44 10.35 7.76
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.24 25.87 18.74 16.81 13.43 11.18 7.91
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 27.76 18.74 17.95 14.45 12.01 7.95
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.65 18.78 17.99 15.39 12.83 8.03
Data and Calculations are only recommendations and for ERIFLEX’s products only
CABS384T / CABS384TN
Phase-Phase Distance
between axis (d): 4.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 37.95 31.65 22.60 18.98 13.94 10.63 9.06 7.24 6.02 -
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 36.50 26.06 21.89 16.06 12.28 10.43 8.35 6.22 -
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.41 23.39 18.11 13.86 11.77 9.21 6.38 -
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 27.44 18.15 15.39 13.07 9.41 6.54 -
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 30.12 18.23 16.89 14.02 9.69 6.69 -
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.98 32.72 18.27 17.24 14.25 9.92 6.89 -
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.31 18.35 17.28 14.53 10.20 7.09 3.98
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.87 18.39 17.36 14.80 10.47 7.28 4.09
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 18.46 17.40 15.04 10.75 7.48 4.17
Phase-Phase Distance
between axis (d): 5.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.13 32.60 23.27 19.57 14.37 10.98 9.33 7.44 6.22 4.02
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 37.64 26.89 22.56 16.57 12.68 10.75 8.62 7.17 4.09
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.31 25.47 18.46 14.29 12.13 9.72 7.40 4.17
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.66 28.27 18.50 15.87 13.50 10.79 7.56 4.25
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 31.02 18.54 17.40 14.80 11.10 7.68 4.33
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.70 18.62 17.48 15.55 11.30 7.83 4.41
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.34 18.66 17.52 15.79 11.57 8.03 4.49
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.98 18.74 17.56 16.02 11.81 8.19 4.61
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 18.78 17.56 16.26 12.09 8.39 4.72
Phase-Phase Distance
between axis (d): 6 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 33.39 23.82 20.00 14.69 11.22 9.53 7.64 6.34 4.61
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 38.54 27.52 23.11 16.97 12.95 11.02 8.82 7.32 4.69
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.06 26.10 18.82 14.65 12.44 9.96 8.31 4.72
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.49 28.98 18.86 16.26 13.82 11.06 8.54 4.80
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.83 31.77 18.90 17.64 15.16 12.13 8.70 4.88
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.53 18.94 17.68 16.46 12.56 8.82 4.96
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.24 18.98 17.72 17.05 12.68 8.98 5.04
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 19.06 17.76 17.20 12.83 9.17 5.16
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 19.09 17.76 17.24 12.99 9.33 5.24
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 6.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.02 24.29 20.39 14.96 11.46 9.72 7.76 6.46 4.84
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.29 28.07 23.58 17.32 13.23 11.26 8.98 7.48 5.28
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.69 26.61 19.13 14.92 12.68 10.16 8.46 5.31
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.20 29.57 19.17 16.61 14.09 11.26 9.41 5.39
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.62 32.44 19.21 17.83 15.47 12.36 9.69 5.43
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.24 19.41 17.87 16.81 13.43 9.84 5.51
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.03 19.69 17.91 17.32 13.58 9.96 5.59
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 20.00 17.95 17.36 13.70 10.12 5.67
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 20.31 17.95 17.36 13.86 10.28 5.79
Phase-Phase Distance
between axis (d): 7.5 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 34.53 24.65 20.71 15.20 11.61 9.88 7.91 6.57 4.92
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.54 23.98 17.60 13.43 11.42 9.13 7.60 5.71
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.24 27.09 19.88 15.20 12.91 10.31 8.58 5.91
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.83 30.08 20.91 16.89 14.33 11.46 9.57 5.94
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.29 33.03 21.14 18.07 15.75 12.60 10.47 6.02
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 35.87 21.38 18.07 17.13 13.70 10.83 6.10
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 38.70 21.65 18.11 17.48 14.45 10.94 6.14
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 21.93 18.15 17.52 14.57 11.10 6.22
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 22.20 18.15 17.52 14.69 11.26 6.34
Phase-Phase Distance
between axis (d): 8.25 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.00 25.00 20.98 15.39 11.77 10.00 7.99 6.65 5.00
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 28.90 24.29 17.83 13.62 11.57 9.25 7.72 5.79
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.68 27.44 20.16 15.39 13.11 10.47 8.74 6.50
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.34 30.51 22.40 17.13 14.57 11.65 9.69 6.54
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.50 23.15 18.27 15.98 12.80 10.67 6.57
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.42 23.39 18.27 17.36 13.90 11.57 6.65
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.29 28.86 18.31 17.64 15.00 11.97 6.73
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 30.91 18.35 17.64 15.39 12.09 6.81
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 32.95 18.35 17.68 15.55 12.24 6.89
Data and Calculations are only recommendations and for ERIFLEX’s products only
Phase-Phase Distance
between axis (d): 9 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.35 25.28 21.22 15.59 11.89 10.12 8.07 6.73 5.04
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.25 24.57 18.03 13.78 11.73 9.37 7.80 5.87
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.07 27.80 20.39 15.59 13.27 10.59 8.82 6.61
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.81 30.91 22.68 17.36 14.72 11.77 9.80 7.13
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.94 24.92 18.46 16.18 12.95 10.79 7.17
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 36.93 27.09 18.50 17.60 14.09 11.73 7.20
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.25 18.50 17.80 15.20 12.68 7.28
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.34 18.54 17.80 16.26 12.76 7.36
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.43 18.54 17.83 16.38 12.87 7.44
Phase-Phase Distance
between axis (d): 9.75 inches
Copper bar sizes (Inch) Distance between axes of busbar supports (inch)
2” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 35.71 25.51 21.42 15.71 12.01 10.20 8.15 6.81 5.08
2.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.57 24.80 18.23 13.94 11.85 9.45 7.87 5.91
3” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.43 28.07 20.63 15.75 13.39 10.71 8.94 6.69
3.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.20 31.26 22.95 17.56 14.92 11.93 9.92 7.44
4” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 34.33 25.20 18.66 16.38 13.11 10.91 7.76
4.5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 37.36 27.44 18.70 17.83 14.25 11.89 7.80
5” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 29.61 18.70 17.91 15.39 12.80 7.87
5.5" X 3/8" 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 31.73 18.74 17.95 16.50 13.39 7.91
6” X 3/8” 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 39.37 33.82 18.74 17.95 17.20 13.46 7.99
Data and Calculations are only recommendations and for ERIFLEX’s products only
Pentair, CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON are owned by Pentair or its global affiliates.
All other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.
© 2017 Pentair.