Basic Electricals Engg. 15ele15 Notes PDF

For More Visit @ www.vtupro.
com
Basic Electrical Engineering 15ELE15
SYLLABUS
Subject Code: 15ELE15/25 IA Marks : 25
No. of Lecture Hrs./ Week : 04 Exam Hours : 03
Total No. of Lecture Hrs. : 52 Exam Marks : 100
Module – 1
1a. D.C.Circuits: Ohm‟s Law and Kirchhoff‟s Laws, analysis of series, parallel and series-
parallel circuits excited by independent voltage sources. Power and Energy. Illustrative
examples.
1b. Electromagnetism: Review of field around a conductor, coil, magnetic flux and flux
density, magneto motive force and magnetic field intensity, reluctance and permeability,
definition of magnetic circuit and basic analogy between electric and magnetic circuits. 5 Hours
Electromagnetic induction: Definition of Electromagnetic Induction, Faradays Laws, Fleming‟s

right hand rule, Lenz‟s Law, Statically and dynamically induced emf. Concept of self-
inductance, mutual inductance and coefficient of coupling. Energy stored in magnetic field.
Illustrative examples. Force on current carrying conductor placed in a magnetic field, Fleming‟s
left hand rule. 5 Hours
Module – 2
2a. D.C.Machines: Working principle of D.C.Machine as a generator and a motor. Types and
constructional features. Types of armature windings, Emf equation of generator, relation between
induced emf and terminal voltage with an enumeration of brush contact drop and drop due to
armature reaction. Illustrative examples, neglecting armature reaction. Operation of D.C. motor,
back emf and its significance, torque equation. Types of D.C. motors, characteristics and
applications. Necessity of a starter for D.C. motor. Illustrative examples on back emf and torque.
7 Hours
2b. Measuring Instruments: Construction and Principle of operation of dynamometer type

wattmeter and single phase induction type energy meter. 3 Hours
Department of EEE, SJBIT Page 1
VTU PRO - A Complete Platform For VTU Students

For More Visit @ www.vtupro.com
Module – 3
3a.Single-phase A.C. Circuits : Generation of sinusoidal voltage, frequency of generated

voltage, definition and numerical values of average value, root mean square value, form factor
and peak factor of sinusoidally varying voltage and current, phasor representation of alternating
quantities. Analysis, with phasor diagrams, of R, L, C, R-L, R-C and R-L-C circuits and, parallel
and series- parallel circuits. Real power, reactive power, apparent power and power factor.
Illustrative examples. 7 Hours
3b. Domestic Wiring: Service mains, meter board and distribution board. Brief discussion on
concealed conduit wiring. Two-way and three-way control. Elementary discussion on Circuit
protective devices: fuse and Miniature Circuit Breaker (MCB‟s). Electric shock, precautions
against shock–Earthing, Earth leakage circuit breaker (ELCB) and Residual current circuit
breaker (RCCB). 3 Hours
Module – 4
4a. Three Phase Circuits : Necessity and advantages of three phase systems, generation of three
phase power. Definition of Phase sequence, balanced supply and balanced load. Relationship
between line and phase values of balanced star and delta connections. Power in balanced three-
phase circuits, measurement of power by two-wattmeter method. Determination power factor
using wattmeter readings. Illustrative examples. 6 Hours
4b. Three Phase Synchronous Generators: Principle of operation, Types and constructional
features, Advantages of rotating field type alternator, Synchronous speed, Frequency of
generated voltage,Emf equation. Concept of winding factor (excluding the derivation of
distribution and pitch factors). Illustrative examples on emf equation. 4 Hours
Module – 5
5a. Single Phase Transformers: Necessity of transformer, Principle of operation and

construction of single-phase transformers (core and shell types). Emf equation, losses, variation
losses with respect to load, efficiency, Condition for maximum efficiency, Voltage regulation
and its significance (Open Circuit and Short circuit tests, equivalent circuit and phasor diagrams
are excluded). Illustrative problems on emf equation and efficiency only. 6 Hours

5b. Three Phase Induction Motors: Principle of operation, Concept and production of rotating
magnetic field, Synchronous speed, rotor speed, Slip, Frequency of the rotor induced emf, Types
and Constructional features. Slip and its significance. Applications of squirrel - cage and slip –
ring motors. Necessity of a starter, starting of motor using stars-delta starter. Illustrative
examples on slip calculations. 4 Hours
TEXT BOOKS
1 “Basic Electrical Engineering”, D C Kulshreshtha, TMH, 2009 Edition.
2 “Fundamentals of Electrical Engineering”, Rajendra Prasad, PHI, Second Edition, 2009.
REFERENCE BOOKS:
1. "Electrical Technology", E. Hughes International Students 9th Edition, Pearson, 2005.
2. “Basic Electrical Engineering”, Abhijit Chakrabarti, Sudiptanath, Chandan Kumar Chanda,

TMH, First reprint 2009.
3. Problems in Electrical Engineering, Parker Smith, CBS Publishers and Distributors, 9th
Edition, 2003.

CONTENTS
Sl.
TOPICS PAGE NO.
No
Module-1: 1a) DC Circuits

1. 5-19
1b) Electromagnetism
Module-2: 2 a) D.C.Machines
2. 20-37
2 b) Measuring Instruments
Module-3 3a) Single-phase A.C. Circuits

3. 38-91
3 b) Domestic Wiring
Module-4 4 a) Three Phase Circuits

4. 92-110
4 b) Three Phase Synchronous Generators
Module-5 5 a) Single Phase Transformers

5. 111-140
5 b) Three Phase Induction Motors

MODULE – 1
1. D. C. Circuits
Ohm‟s Law : the current flowing through the electric the electric circuit is directly proportional
to the potential difference across the circuit and inversely proportional to the resistance of the
circuit, provided the temperature remains constant.
The limitations of the Ohm‟s law are,
1) It is not applicable to the nonlinear devices such as diodes, zener diodes, voltage
regulators ect.
2) It does not hold good for non-metallic conductors such as silicon carbide.
The law for such conductors is given by,
V = K Im where k, m are constants.
( I ) Current is what flows on a wire or conductor like water flowing down a river. Current flows
from negative to positive on the surface of a conductor. Current is measured in (A) amperes or
amps.
( E ) Voltage Ohm's Law defines the relationships between (P) power, (E) voltage, (I) current,
and (R) resistance. One ohm is the resistance value through which one volt will maintain a
current of one ampere is the difference in electrical potential between two points in a circuit. It's
the push or pressure behind current flow through a circuit, and is measured in (V) volts.
( R ) Resistance determines how much current will flow through a component. Resistors are used
to control voltage and current levels. A very high resistance allows a small amount of current to
flow. A very low resistance allows a large amount of current to flow. Resistance is measured in
ohms.

To make a current flow through a resistance there must be a voltage across that resistance. Ohm's
Law shows the relationship between the voltage (V), current (I) and resistance (R). It can be
written in three ways:
V V
V=I×R or I= or R=
R I
where: V = voltage in volts (V) or: V = voltage in volts (V)

I = current in amps (A) I = current in milliamps (mA)
R = resistance in ohms ( ) R = resistance in kilohms (k )

State and explain Kirchhoff’s laws.
Kirchhoff‟s current law:
The law can be stated as,
The total current flowing towards a junction point is equal to the total current flowing y from
that junction point.
 The word algebraic means considering the signs of various currents.
at junction point = 0
 Sign convention : Currents flowing towards a junction point are assumed to be positive
whie currents flowing away from a junction point assumed to be negative.
 e.g. Refer to Fig. 1, currents I1 and I2 are positive while I3 and I4 are negative.
 Applying KCL, at junction 0 = 0
 I1 + I2 - I3 - I4 = 0 i.e. I1 + I2 = I3 + I4
 The law is very helpful in network simplification.

Kirchhoff’s voltage law :
“In any network, the algebraic sum of the voltage drops across the circuit elements of any
closed path (or loop or mesh) is equal to the algebraic sum of the e.m.f s in the path”
In other words, “the algebraic sum of all the branch voltages, around any closed path or
closed loop is always zero.”
Around a closed path =0
The law states that if one starts at a certain point of a closed path and goes on tracing and
noting all the potential changes (either drops or rises), in any one particular direction, till
the starting point reached again, he must be at the same potential with which he started
tracing a closed path.
Sum of all the potential rises must be equal to sum of all the potential drops while tracing
any closed path of the circuit. The total change in potential along a closed path is always
zero.
This law is very useful in loop analysis of the network.
A circuit consists of two parallel resistors having resistance of 20 and 30
respectively connected in series with 15 .If current through 15 resistor is 3 A,
Resistance
Resistance is the property of a component which restricts the flow of electric current. Energy
is used up as the voltage across the component drives the current through it and this energy
appears as heat in the component.

Resistors connected in Series
When resistors are connected in series their combined resistance is equal to the individual
resistances added together. For example if resistors R1 and R2 are connected in series their
combined resistance, R, is given by: Combined resistance in series:
R = R1 + R2
This can be extended for more resistors: R = R1 + R2 + R3 + R4 + ...
Note that the combined resistance in series will always be greater than any
of the individual resistances.
Resistors connected in Parallel
When resistors are connected in parallel their combined resistance is less than any of the
individual resistances. There is a special equation for the combined resistance of two resistors R1
and R2:
Combined resistance of R1 × R2
two resistors in parallel: R =
R1 + R2
For more than two resistors connected in parallel a more difficult equation must be used. This
adds up the reciprocal ("one over") of each resistance to give the reciprocal of the combined
resistance, R:
1 1 1 1
= + + + ...
R R1 R2 R3
The simpler equation for two resistors in parallel is much easier to use!

Note that the combined resistance in parallel will always be less than any of the individual
resistances.
( P ) Power is the amount of current times the voltage level at a given point measured in wattage
or watts.
electrical energy - energy made available by the flow of electric charge through a conductor;
"they built a car that runs on electricity" measured in k Watt Hour
Energy=VItKWhour
Faraday’s Laws:
1st law: Whenever magnetic flux linking with a coil changes with time an emf is induced
in that coil or whenever a moving conductor cuts the magnetic flux, an emf is induced in
the conductor.
2nd law: The magnitude of the induced emf is equal to the product of the number of turns
of the coil and the rate of change of flux linkage.
Lenz’s law :
It states that the direction of an induced emf produced by the electromagnetic induction is
such that it sets up a current which always opposes the cause that is responsible for inducing the
emf.
In short the induced emf always opposes the cause producing it which is represented by
negative sign, mathematically in its expression
Consider a solenoid as shown in Fig.1. Let a bar magnet is moved towards coil such that N-pole
of magnet is facing a coil which will circulate the current through the coil.
According to Lenz‟s law, the direction of current due to induced emf is so as to oppose the
cause. The cause is motion of bar magnet towards coil So emf will set up a current through coil
in such a way that the end of solenoid facing bar magnet will become N-pole. Hence two like
poles will face each other experiencing force of repulsion which is opposite to the motion of bar
magnet as shown in the above

Fleming’s rules:
1. Fleming‟s Right hand rule: This rule helps in deciding the direction of the induced
emf.
Hold the right hand thumb, fore finger and the middle finger set at right
angles to each other and the thumb points the direction of the motion of the
conductor and the fore finger points the direction of the field and the middle
finger points the direction of the induced emf.
2. Fleming’s Left hand rule: This rule helps in deciding the direction of
force acting on a conductor.

 Hold the left hand thumb, fore finger and the middle finger set at right angles to
each other and the thumb points the direction of the force acting on the conductor
and the direction of the fore finger points the direction of the magnetic field and the
middle finger points the direction of the current in the conductor
The emf induced in a coil due to change of flux linked with it (change of flux is by the
increase or decrease in current) is called statically induced emf.Transformer is an example of
statically induced emf. Here the windings are stationary, magnetic field is moving around the
conductor and produces the emf.
Dynamically induced emf
The emf induced in a coil due to relative motion of the conductor and the magnetic field is
called dynamically induced emf.
Example: dc generator works on the principle of dynamically induced emf in the conductors
which are housed in a revolving armature lying within magnetic field
Statically induced e.m.f
The change in flux lines with respect to coil can be achieved without physically moving
the coil or the magnet. Such induced e.m.f. in a coil which is without physical movement of coil
or a magnet is called statically induced e.m.f.
To have an induced e.m.f there must be change in flux associated with a coil. Such a
change in flux can be achieved without any physical movement by increasing and decreasing the
current producing the flux rapidly, with time.
Consider an electromagnet which is producing the necessary flux for producing e.m.f.
Now let current through the coil of an electromagnet be an alternating one. Such alternating
current means it changes its magnitude periodically with time. This produces the flux which is
also alternating i.e. changing with time. Thus there exists associated with coil placed in the
viscinity of an electromagnet. This is responsible for producing an e.m.f in the coil. This is called
statically induced e.m.f.
There is no physical movement of magnet or conductor; it is the alternating supply which

is responsible for such an induced e.m.f.
Such type of an induced e.m.f. is available in transformers.

Dynamically induced e.m.f.
The change in the flux linking with a coil, conductor or circuit can be brought about by
its motion relative to magnetic field. This is possible by moving flux with respect to coil
conductor or circuit or it is possible by moving conductor, coil, circuit with respect to stationary
magnetic flux.
Such an induced e.m.f. which is due to physical movement of coil, conductor with
respect to flux or movement of magnet with respect with to stationary coil, conductor is called
dynamically induced e.m.f. or motional induced e.m.f.
This type of induced e.m.f. is available in the rotating machines such as alternators,
generator etc.
Self inductance :
According to Lenz‟s law the direction of this induced e.m.f. will be so as to oppose the
cause producing it. The cause is the current I hence self-induced e.m.f will try to set up a current
which is in opposite direction to that of current I. When current is increased, self-induced e.m.f.
reduces the current tries to keep to its original value. If current is decreased, self-induced e.m.f.
increases the current and tries to maintain it back to its original value. So any change in current
through coil is opposed by the coil.
This property of the coil which opposes any change in the current passing through it is
called self-inductance or only inductance.
It is analogous to electrical inertia or electromagnetic inertia.
The formula for self-inductance is given by,
L=
It can be defined as flux linkages per ampere current in it. Its unit is Henry (H)
Expressions for coefficient of self-inductance (L):
L=
But =
∴ L =

∴ L= henries
Now s
L=
∴ L = = Henries
Where l = length of magnetic circuit
a = area of cross-section of magnetic circuit which flux is passing.
Derive an Expression for energy stored in the inductor:
Let the induced e.m.f. in a coil be,

e = -L
This opposes a supply voltage. So supply voltage „V‟ supplies energy to overcome this, which
ultimately gets stored in the magnetic field.
∴ V = -e = - =L
Power supplied = V × I = L ×I
Energy supplied in time dt is,

E = power x time = L x I x dt
= L di x I joules.
This is energy supplied for a change in current of dI but actually current changes from zero to I.
∴ Integrating above total energy stored is,
E=
State i) Fleming’s right hand rule, and

ii) Fleming’s left hand rule. And Mention their applications.
Fleming’s right hand rule : The Fleming‟s left hand rule is used to get direction of force
experienced by conductor carrying current placed in magnetic field while Fleming‟s right hand
rule can be used to get direction of induced e.m.f. when conductor is moving at right angles to
the magnetic field.

According to this rule, outstretch the three fingers of right hand namely the thumb, fore
finger and the middle finger, perpendicular to each other. Arrange the right hand so that finger
point in the direction of flux lines ( from N to S ) and thumb in the direction of motion of
conductor with respect to the flux then the middle finger will point in the direction of the induced
e.m.f. ( or current ).
Fleming’s left hand rule: The direction of the force experienced by the current carrying
conductor placed in magnetic field can be determined by a rule called „Fleming‟s left hand rule‟.
The rule states that „ outstretch the three fingers on the left hand namely the first finger, middle
finger and thumb such that they are mutually perpendicular to each other. Now point the first
finger in the direction of magnetic field and middle finger in the direction of the current then the
thumb gives the direction of the force experienced by the conductor.‟
The rule is explained in the diagrammatic form in fig. 2.

Applications: Fleming‟s right hand rule is used to get the direction of induced emf in case of
generators and alternators while left hand rule is used to get the direction of torque induced in
motors.
Mutual inductance:
Magnitude of mutually induced e.m.f

Let N1 = Number of turns of coil A
N2 = Number of turns of coil B
I1 = Current flowing through coil A
∅1 = Flux produced due to current I1 in webers.
∅2 = Flux linking with coil B
According to Faraday‟s law, the induced e.m.f. in coil B is,
e2 =
Negative sign indicates that this e.m.f will set up a current which will oppose the change of flux
linking with it.
Now ∅2 =
If permeability of the surroundings is assumed constant then ∅2 ∝ I1 and hence ∅∕I1 is constant.
∴ Rate of change of ∅2 = Rate of change of current I1

Here is called co efficient of mutual inductance dented by M
Volts
Coefficient of mutual inductance is defined as the property by which e.m.f gets induced in the
second coil because of change in current through first coil.
Coefficient of mutual inductance is defined as the property by which e.m.f gets induced in the
second coil because of change in current through first coil.
Coefficient of mutual inductance is also called mutual inductance. It is measured in Henries.
Definitions of mutual inductance and its unit:

1) The coefficient of mutual inductance is defined as the flux linkages of the coil per ampere
current in other coil.
2) It can also be defined as equal to e.m.f induced in volts in one coil when current in other
coil changes uniformly are rate of one ampere per second.
Similarly its unit is defined as follows:
1) Two coils which are magnetically coupled are said to have mutual inductance of one
hence when a current of one ampere flowing through one coil produces a flux linkage of
one Weber turn in the other coil.
2) Two coils which are magnetically coupled are said to have mutual inductance of one
Henry when a current changing uniformly at the rate of one ampere per second in one
coil, induces as e.m.f of one volts in the other coil.
Expressions of the mutual inductance (M):
1)
2) ∅2 is the part of the flux ∅1 produced due to I1. Let K1 be the fraction of ∅1 which is linkage
with coil B.
∴

3) The flux ∅1 can be expressed as,
∅1 =
If all the flux produced by the coil A links with coil B K1= 1.
4) Now and K1 = 1
Then
5) If second coil carries current I2, producing flux ∅2, the part of which links with coil A i.e.∅1
then,
∅1 = K2 ∅2 and
Now
= therefore =
Coupling Coefficient: The coefficient of coupling is define as the ratio of the actual mutual
inductance present between the two coils as the maximum possible value of the mutual
inductance. It gives an idea about magnetic coupling between the two coils. This coefficient
indicates the amount of linking with other coil which is produced by one coil.
Let N1 = Number of turns of first coil
N2 = number of turns of second coil

I1 = current through first coil
I2 = current through by first coil
1= flux produced by first coil
2= flux produced by second coil
M= and M =
Multiplying the two expressions,
M×M= ×
M2 = K1K2
But = L1 = self-inductance of first coil
And = L2 = self-inductance of second coil
M2 = K1K2L1L2
M=
Let K= = coefficient of coupling
M=K
K=

MODULE – 2
2a. D.C.Machines:
A machine which works on direct current is defined as a D.C.Machine.
D.C.Machines are of two types. (i) D.C.Generator and (ii) D.C.Motor.
Sl.No. D.C. Generator D.C.Motor
1 Definition: Definition:
A generator is a rotating machine which A motor is a machine which converts

converts mechanical energy into electrical electrical energy into mechanical
energy energy
2 Principle: Principle:
Whenever a coil is rotated in a magnetic Whenever a current coil is placed

field an e.m.f. will be induced in this coil under a magnetic field the coil
experiences a mechanical force, and is
and is given by e=BlvSinθ volts/coil side given by F= BIlSinθ Newtons/coil
where, B=The flux density in Tesla, l=the side.
active length of the coil side in meters, Where, I is the current through the coil
v=the velocity with which the coil is in ampere.
moved in meters/sec and θ is the angle
between the direction of the flux and the
direction of rotation of the coil side.
3 The direction of the emf induced is fixed The direction of the force acting is
by applying the Fleming‟s right hand rule fixed by applying the Fleming‟s left
hand rule.
Types and constructional features
Salient parts of a D.C.machine are:
 Field system (poles)

 Coil arrangement (armature)
 Commutator
 Brushes
 Yoke

Fig shows the details of a four pole D.C. machine with both shunt and series field windings.
It consists of the following parts:

Yoke:
a) Functions :
i) It serves the purpose of outermost cover of the d.c. machine. So that the insulating materials
get protected from harmful atmospheric elements like moisture, dust and various gases like SO2,
acidic fumes etc.
ii) It provides mechanical support to the poles.
iii) It forms a part of the magnetic circuit. It provides a path of low reluctance for magnetic flux.
The low reluctance path is important to avoid wastage of power to provide same flux. Large
current and hence the power is necessary if the path has high reluctance, to produce the same
flux.
b) Choice of material: To provide low reluctance path, it must be made up of some magnetic
material. It is prepared by using cast iron because it is cheapest. For large machines rolled steel,
cast steel, silicon steel is used which provides high permeability i.e. low reluctance and gives
good mechanical strength.As yoke does not need any machining or

good finishing as it rough, casting is the best method

of construction of yoke.
Poles:
Each pole is divided into two parts Namely,
a) pole core and b) pole shoe This is shown in fig. 27.
a) Function of pole core and pole shoe:

i) pole core basically carries a field winding which is necessary to produce the flux.
ii) It directs the flux produced through air gap to armature core, to the next pole.
iii) pole shoe enlarges the area of armature core to come across the flux, which is necessary
to produce larger induced e.m.f. to achieve this, pole shoe has given a particular shape.
b) Choice of material : It is made up of magnetic material like cast iron or cast steel.as it
requires a definite shape and size, laminated construction is used. The laminations of required
size and shape are stamped together to get a pole, which is then bolted to the yoke.
Field winding [F1-F2] :

The field winding is wound on the pole core with a definite direction.
a) Functions: i) To carry current due to which pole core on which the winding placed behaves as
an electromagnet, producing necessary flux.
As it helps in producing the magnetic field i.e. exciting the pole as electromagnet it is
called „Field winding‟ or „Exciting winding‟.
3) Explain Choice of material: As it has to carry current hence obviously made up of some
conducting material. So aluminium or copper is the choice. But field coils are required
to take any type of shape and bend about pole core and copper has good pliability i.e. it
can bend easily. So copper is the proper choice.
Filed winding is divided into various coils called bas field coils. These are connected in series
with each other and wound in such a direction around pole cores, such that alternate „N‟ and „S‟
poles are formed.

By using right hand thumb rule for current carrying circular conductor, it can be easily
determined that how a particular core is going to behave as „N‟ or „S‟ for a particular winding
direction around it.
Armature:
It is further divided into two parts namely,
I) Armature core and II) Armature winding
I) Armature core is cylindrical in shape mounted on the shaft. It consists of slots on its
periphery and the air ducts to permit the air flow through armature which serves cooling purpose.
a) Functions:
i) Armature core provides house for armature winding i.e. armature conductors.
ii) To provide a path of low reluctance to the magnetic flux produced by the field winding.
b) Choice of material : A it has to provide a low Reluctance path to the flux, it is made up of
magnetic material like cast iron or cast steel.
It is made up of laminated Construction to keep eddy current Loss as low as possible. A single
circular Lamination used for the construction of the armature core is shown in Fig. 28.
II) Armature winding is nothing but the interconnection of the armature conductors, placed in
the slots provided on the armature core periphery. When the armature is rotated, in case of
generator, magnetic flux gets cut by armature conductors and e.m.f. gets induced in them.
a) Functions:
i) Generation of e.m.f. takes place in the armature winding in case of generators.
ii) To carry the current supplied in case of d.c. motors
iii) To do the useful work in the external circuit.

b) Choice of material: As armature windings carries entire current which depends on external
load, it has to be made up of conducting material, which is copper.
Armature winding is generally former wound. The conductors are placed in the armature
slots which are lined with tough insulating material.
Commutator:
We have seen earlier that the basic nature of e.m.f induced in the armature conductors is
alternating. This needs rectifications in case of d.c. generator which is possible by device called
commutator.
a) Functions:
i) To facilitate the collection of current from the armature conductors.
ii) To convert internally developed alternating e.m.f. to unidirectional (d.c.) e.m.f.
iii) To produce unidirectional torque in case of motors.
b) Choice of material: As it collects current from armature, it is also made up of copper
segments.
It is cylindrical in shape and is made up of wedge shaped segments of hard drawn, high
conductivity copper. Those segments are insulated from each other by thin layer of mica. Each
commutator segment is connected to the armature conductor by means of copper lug or strip.
This connection is shown in the fig.

Brushes and brush gear:

Brushes and stationary and resting on the surface of the commutator.
a) Functions:
i) To collect current from commutator and make it available to the stationary external circuit.
b) Choice of material: Brushes are normally made up of soft material like carbon. Brushes are
rectangular in shape. They are housed in brush holders, which are usually of box type. The
brushers are made to press on the commutator surface by means of a spring, whose tension can
be adjusted with the help of lever. A flexible copper conductor called pig tail is used to connect
the brush to the external circuit.
Bearings:
Ball bearings are usually as they are more reliable. For heavy duty machines, roller bearings are
preferred.

Comparison of lap and wave windings:
LAP WAVE
Number of armature parallel paths Number of parallel paths is always

is equal to the number of poles. equal to two.
Preferred when large current at Preferred when large voltage with

lesser voltage is the requirement. lesser current is the requirement.
1. A 500V shunt motor has 4 poles and a wave connected winding with 492 conductors. The
flux per pole is 0.05 Wb. The full load current is 20 Amps. The armature and shunt field
resistances are 0.1 and 250 respectively. Calculate the speed and the developed torque.
Sol:
P = 4, V =500volts
Φ = 0.05Wb
Z = 492
IL = IF.L. = 20A
Ra = 0.1
Rsh = 250 ,A = 2 for wave winding

Ish = = = 2A
IL = Ia + Ish Ia = IL – Ish = 20-2 = 18A
Now, Eb = =
But, Eb = V-IaRa = 500-(18)(90.1) = 500-1.8
498.2 =
N=
N = 607.56 rpm
Now, Eb∙Ia = Ta × ω
Ta = =
Ta =
Ta = 140.94N-m) A 250 KVA, 11000/415V, 50 Hz single phase
Principle: Whenever a current coil is placed in a magnetic field the coil experiences a
Mechanical force, and is given by
F=BIlSinθ newtons. Where B is the flux density in Tesla
I is the current through the coil
l is the active length of the coil side
θ is the angle between the movement of the
coil and the direction of the flux
The direction of the force acting can be decided by applying Fleming‟s left hand rule.
The construction of a D.C.Motor is same as the construction of a D.C.generator.

Types of D.C.Motors:
Depending on the interconnection between the armature and the field circuit D.C.Motors are
classified as (i) Shunt Motor, (ii) Series Motor and (iii) Compound motors just like
D.C.Generators.
Back EMF:
Whenever a current coil is placed under a magnetic field the coil experiences a mechanical
force due to which the coil starts rotating. This rotating coil again cuts the magnetic lines of
force resulting an EMF induced in it whose direction is to oppose the applied EMF (as per
Fleming‟s right hand rule), and hence the name BACK EMF or Counter Emf.
Significance of Back EMF: Back EMF is a must in a motor which helps to regulate the
armature current and also the real cause for the production of torque.
Expression for the back Emf is given by E=V-IaRa,
Where E is the back emf, V is the applied emf, Ia is the armature current and Ra is the armature
circuit resistance. And also E= PZNФ/60A volts, from the machine parameters.
Production of torque in a D.C. Motor.
The production of torque in a d.c. motor can be well explained with the help of the following
figures.
Fig (a) represents the magnetic field distribution between a bipolar magnet from North pole to
South pole.
Fig(b) shows the field set up around a current carrying coil
In fig © the current carrying coil is brought under the influence of bipolar magnetic field.
The resultant field around the coil due to the inter action of the main field and the coil field is
seen in fig (d) where in the flux is strengthened in the left part of the upper coil side and
weakened in the right part of the upper coil side and vice-versa in the lower coil side. The
resultant flux which strengthened at one point exerts a force on the conductor as per Fleming‟s
left hand rule and thereby the coil side experiences a mechanical force.
In the construction it is seen that several coils sides are on the armature and the tangential force
acting on each of these coil sides add each other and resulting in a unidirectional movement
which makes the armature to rotate at a uniform speed thereby torque is produced.

TORQUE EQUATION:
Let P be the total number of poles, Z be the total number of armature conductors arranged in A
number of parallel paths. Let Ф be the flux per pole, N be the speed of rotation in rpm, and T be
the torque in Nm.
We know that the back emf E=V-IaRa
It is seen that the turning or twisting force about an axis is called torque.
Consider a wheel of radius R meters, acted upon by a

Circumferential force of F Newton‟s as shown in fig. 30.
The wheel is rotating at a speed of N r.p.m.
Then angular speed of the wheel is,
So work done in one revolution is,

W = F× distance travelled in one revolution
= F× 2πR joules
And Pm = power developed =
Pm = T×ω
where T = Torque in N-m = (F×R)
. ω = angular speed in rad/sec = (2 N/60)

Let Ta be the gross torque developed by the armature of the motor. It is also called armature
torque. The gross mechanical power developed in the armature is Eb Ia, as seen from the power
equation. So if speed of the motor is N r.p.m. then,
Power in armature = Armature torque × ω
But Eb in a motor given by, Eb =
∴ N-m
This is the torque equation of a d.c.motor.
2. A 4 pole generator with wave wound armature has 51 slots, each having 24 conductors.
The flux per pole is 0.01 Weber. At what speed must the armature rotate to give an induced
emf of 220 V? What will be the voltage developed if the voltage developed if the winding is
lap and the armature rotates at the same speed?
sol.: P = 4, for wave winding A = 2
Number of slots = 51, conductors/slot = 24
∅ = 0.01 wb;
E = 220 volts
Z = Number of slots × conductors/slots
= 51 × 24
= 1224
E=
N= =
N = 539.21 rpm
Now speed is same but winding is lap A=P

E=
E = 110 volts
2. A 4 pole, 220 V. lap connected DC shunt motor has 36 slots, each slot containing 16
conductors. It draws a current of 40 A from the supply. The field resistance and armature
resistance are 110 , 0.1 respectively. The motor develops an output power of 6 kW. The
flux per pole is 40 mwb. Calculate
a) the speed b) the torque developed by the armature and c) the shaft torque
Sol.: P = 4, V = 220 volts, slots = 36, A=P=4
Conductors/slot = 16, Z = 36 × 16 = 576
IL = 40 A
R sh = 110 = 0.1
P output = 6 KW, ∅ = 40× wb
Ish =
IL = Ia+Ish
Ia = IL - Ish
= 40 – 2 = 38A
Eb = V - IaRa
Eb = 220 – (38) (0.1)
= 220-3.8
Eb = 216.2 volts
Now, Eb = N= =
N = 563 rpm
Ta = 0.159 ∅ Z = 0.159 ∅ ZIa

= (0.159) (40× 10 -3) (576) (38)
T a = 139.20 N-m
P out = T sh .
Tsh = = 101.76 N-m
T sh = 101.76 N-m
Characteristics of D.C.Motors: To study the performance of a motor it is necessary to study

the variation of its speed and torque with the variations of the load on it.
There are two types of characteristics: (i) Speed v/s load characteristics
(ii) Torque v/s load characteristics
1. Speed/Load characteristics: (a) D.C.Shunt Motor:
In a shunt motor the flux is considered to be constant because of the reason that the
field circuit is connected across a constant power supply. Also as the applied voltage is constant
the speed is directly proportional to the armature current only, and also as the load is increased
the armature current also increases at the same rate and the speed becomes constant. But due to
the increased friction at the bearings with the increase of the load there is a small decrease in the
speed. The characteristic is shown in the fig. and is compared with the ideal characteristics. The
drop in the speed can be reduced by slightly de-exciting the field flux, there by the speed is
controlled.
(b) Series Motor:
In a series motor the flux is solely dependent on the armature current hence the speed variation
with load is not like shunt motor. At no load condition only residual flux is in action which is
very very small resulting in a dangerously high speed. Therefore series motors are not to be
started on no load, which result in the initial speed of dangerously high value called RUN
AWAY SPEED which severely damages the motor. Hence in series motors there is a provision

of a fly wheel fixed to the shaft which acts like a mechanical load to prevent the motor to attain
this high speed.
characteristics of D.C. i) series and ii) shunt motors. Mention two applications of each motor
DC series motor :
i) N=1 characteristics :
ii) T-I characteristics :
Applications: Cranes, trolleys .

2. DC shunt motor :
i) N-I characteristics

ii) T-I characteristics:
2b. Measuring Instruments:

DYNAMOMETER WATTMETER:-
In this type there will not be any permanent magnets and there will be a pair of fixed coils
connected in series when energized gives the same effect as that of the permanent magnets. In
the field of these fixed coils there will be a moving coil which when energized acted upon by a
torque by which it deflects
F1 F2: Fixed coils
M: Moving coil
R: High resistance in series with m
I1 : load current
I2: current through
The two fixed coils in series act as the current coil and the moving coil in series with R act as the
potential coil. The moving coil is pivoted between the two fixed coils carries a current I2

proportional to V. This current is fed to m through two springs which also provides the necessary
controlling torque. This instrument can be used on both ac and dc circuits as both the coils are
energized simultaneously by a common source due to which a unidirectional torque is produced.
INDUCTION TYPE ENERGY METER:-
This is a measuring instrument/device which works on the principle of induction and

measures the energy consumed over a definite period.
1) Upper Magnet/ shunt magnet (P.P)
2) Potential coil/ Voltage coil
3) Copper Shading bands
4) Friction compensator
5) Aluminium disc
6) Brake magnet
7) Lower magnet/Series magnet
8) Current coil (C-C)
This instrument consisting two electromagnets as in fig.

1. Upper magnet or Shunt magnet: which carries the potential coil on its central limb
which also carries one or two copper shading bands for the power factor adjustment.
2. Lower magnet or Series magnet: Which carries the current coil as shown. An
aluminum disc is between the fields of the upper and lower electro magnets. There is a friction
compensator in the upper magnets for the measurement at very low loads. The aluminum disc
rotates in the field of a brake magnet whose position can be set so that the disc rotates at proper
speeds at higher loads.
This instrument works on the principle of induction that when both the shunt and series coils
are energized by ac, there will be tow alternative fluxes are in the shunt coil and one in the series
coil these time varying fluxes are cut by a stationary disc. Inducing currents in the disc. These
currents interacts with the fluxes and results in a torque which is given by
T k1 i
sh se K2 i
se sh there by the disc rotates in a particular direction and the number and
speed of rotations depends on the energy consumed by the load.
Sometimes the energy meters disc rotates slowly even on no load conditions as the
potential coil is continuously energized and this effect is called the „CREEP‟ and the speed is
called the „CREEP SPEED‟ to minimum this creep one pair of diametrically opposite holes are
made in the aluminum disc which alters the reluctance and minimizes the creep effect.

MODULE – 3
3a.Single-phase A.C. Circuits:
Generation of sinusoidal AC Voltage:
Alternating voltage may be generated:
a) By rotating a coil in a magnetic field as shown in Fig.3.1.

b) By rotating a magnetic field within a stationary coil as shown in Fig.3.2.
“ In each case, the value of the alternating voltage generated depends upon the number of turns
in the coil, the strength of the field and the speed at which the coil or magnetic field rotates.”
The alternating voltage generated has regular changes in magnitude and direction. If a load
resistance (e.g. a light bulb) is connected across this alternating voltage, an alternating current
flows in the circuit. When there is a reversal of polarity of the alternating voltage, the direction
of current flow in the circuit also reverses.
Equation of Alternating E.M.F.
Let us take up the case of a rectangular coil of N turns rotating in the anticlockwise direction,
with an angular velocity of ω radians per second in a uniform magnetic field as shown in Fig.3.3.
let the time be measured from the instant of coincidence of the plane of the coil with the
X-axis. At this instant maximum flux max‟ links with the coil. As the coil rotates, the flux linking
with it changes and hence e.m.f. is induced in it. Let the coil turn through an angle θ in time„t‟
seconds, and let it assume the position as shown in Fig.3.3. Obviously θ = ωt.

When the coil is in this position, the maximum flux acting vertically downwards can be
resolved into two components, each perpendicular to the other, namely:
a) Component max sin ωt, parallel to the plane of the coil. This component does not induce
e.m.f. as it is parallel to the plane of the coil.
b) Component max cos ωt, perpendicular to the plane of coil. This component induces e.m.f.
in the coil.
flux linkages of coil at that instant (at θ0) is
= No. of turns x flux linking
=N max cos ωt
As per faraday‟s Laws of Electromagnetic induction, the e.m.f. induced in a coil is equal to
the rate of change of flux linkages of the coil. So, instantaneous e.m.f. „e‟ induced in the coil at
this instant is:
e=- (flux linkages)
=- (N max cos ωt)
=-N max (cos ωt)
= -N max ω (-sin ωt)
e=+N max sin ωt volts . . . (1)
It is apparent from eqn.(1) that the value of „e‟ will be maximum (Em), when the coil has rotated
through 900 (as sin 900 = 1)
Thus Em = N ω max volts ... (2)
Substituting the value of N ω max from eqn.(2) in eqn.(1), we obtain:

e = Em sin ωt . . .(3)
We know that θ = ωt
e = Em sin θ
It is clear from this expression of alternating e.m.f. induced in the coil that instantaneous
e.m.f. varies as the sin of the time angle (θ or ωt).
ω = 2πf, where „f‟ is the frequency of rotation of the coil. Hence eqn.(3) can be written as
e = Em sin 2πft . . . (4)
If T = time of the alternating voltage = , then eqn.(iv) may be re-written as
e = Em sin t
so, the e.m.f. induced varies as the sine function of the time angle, ωt, and if e.m.f. induced is
plotted against time, a curve of sine wave shape is obtained as shown in Fig.3.4. Such an e.m.f. is
called sinusoidal when the coil moves through an angle of 2π radians.
Equation of Alternating Current
When an alternating voltage e = Em sin ωt is applied across a load, alternating current flows
through the circuit which will also have a sinusoidal variation. The expression for the alternating
current is given by:
i = Im sin ωt
In this case the load is resistive (we shall see, later on, that if the load is inductive or capacitive,
this current-equation is changed in time angle).

Important Definitions
Important terms/definitions, which are frequently used while dealing with a.c. circuits, are
as given below:
1. Alternating quantity: An alternating quantity is one which acts in alternate positive and
negative directions, whose magnitude undergoes a definite series of changes in definite
intervals of time and in which the sequence of changes while negative is identical with the
sequence of changes while positive.
2. Waveform: “The graph between an alternating quantity (voltage or current) and time is
called waveform”, generally, alternating quantity is depicted along the Y-axis and time
along the X-axis.fig.4.4 shows the waveform of a sinusoidal voltage.
3. Instantaneous value: The value of an alternating quantity at any instant is called
instantaneous value.
The instantaneous values of alternating voltages and current are represented by „e‟ and „I‟
respectively.
4. Alternation and cycle: When an alternating quantity goes through one half cycle (complete
set of +ve or –ve values) it completes an alternation, and when it goes through a complete
set of +ve and –ve values, it is said to have completed one cycle.
5. Periodic Time and Frequency: The time taken in seconds by an alternating quantity to
complete one cycle is known as periodic time and is denoted by T.
The number of cycles completed per second by an alternating quantity is know as
frequency and is denoted by „f‟. in the SI system, the frequency is expressed in hertz.
The number of cycles completed per second = f.
Periodic Time T – Time taken in completing one cycle =
Or f =
In India, the standard frequency for power supply is 50 Hz. It means that alternating voltage
or current completes 50 cycles in one second.

6. Amplitude: The maximum value, positive or negative, which an alternating quantity attains
during one complete cycle, is called amplitude or peak value or maximum value. The
amplitude of alternating voltage and current is represented by Em and Im respectively.
Different Forms of E.M.F. Equation
The standard form of an alternating voltage, as already mentioned in sec.3.2 is
e = Em sin θ = Em sin ωt = Em sin 2πf t = Em sin t
on perusal of the above equations, we find that
a) The amplitude or peak value or maximum value of an alternating voltage is given by

the coefficient of the sine of the time angle.
b) The frequency „f‟ is given by the coefficient of time divided by 2π.
Taking an example, if the equation is of an alternating voltages is given by e = 20 sin 314t,

then its maximum value is 20 V and its frequency is
f= 50 Hz
In a like manner, if the equation is of the form
e = Im sin 2 ωt, then its maximum value is
Em = Im and the frequency is
Or Hertz
Root-mean-square (R.M.S.) Value:
The r.m.s. or effective value, of an alternating current is defined as that steady current which
when flowing through a given resistance for a given time produces the same amount of heat as
produced by the alternating current, when flowing through the same resistance for the same time.

Let us take two circuits with identical resistance, but one is connected to a battery and the
other to a sinusoidal voltage source. Wattmeters are employed to measure heat power in each
circuit. The voltage applied to each circuit is so adjusted that the heat power produced in each
circuit is the same. In this event the direct current I will equal , which is termed r.m.s. value of
the sinusoidal current.
The following method is used for finding the r.m.s. or effective value of sinusoidal waves.
The equation of an alternating current varying sinusoid ally is given by i= Im sin θ.
Let us consider an elementary strip of thickness dθ in the first cycle of the squared wave, as
shown in Fig.3.5.
Let i2 be mid-ordinate of this strip.
Area of the strip = i2 d θ
Area of first half-cycle of squared wave
= dθ
= dθ (∵ I = Im sin θ)

= Im2 d (∵ sin2 =
I=
= = 0.707Im
Hence, for a sinusoidal current,
R.M.S. value of current = 0.707 x maximum value of current.
Similarly, E = 0.707 Em
Average Value
The arithmetical average of all the values of an alternating quantity over one cycle is called
average value.
In the case of a symmetrical wave e.g. sinusoidal current or voltage wave, the positive half
is exactly equal to the negative half, so that the average value over the entire cycle is zero.
Hence, in this case, the average value is obtained by adding or integrating the instantaneous
values of current over one alternation (half-cycle) only.
The equation of a sinusoidally varying voltage
Is given by e = Em sin θ.

Let us take an elementary strip of thickness dθ in the first half-cycle as shown in Fig.3.6. let
the mid-ordinate of this strip be „e‟.
Area of the strip = e dθ
Area of first half-cycle
= dθ
= dθ (∵ e = Em sin θ)
= Em dθ
= Em = 2Em
Average value, Eav =
Or Eav = 0.637 Em
In a similar manner, we can prove that, for alternating current varying sinusoidally,
Iav = 0.637 Im
Average value of current = 0.637 x maximum value
Form Factor and crest or peak or Amplitude Factor (Kf)
A definite relationship exists between crest value (or peak value), average value and r.m.s.
value of an alternating quantity.
1. Form Factor: The ratio of effective value (or r.m.s. value) to average value of an
alternating quantity (voltage or current) is called form factor, i.e.
From Factor, Kf =

For sinusoidal alternating current,
Kf = = 1.11
For sinusoidal alternating voltage,
Kf = = 1.11
Hence, the R.M.S. value (of current or voltage) is 1.11 times its average value.
2. Crest or Peak or Amplitude Factor (Ka): It is defined as the ratio of maximum value to
the effective value (r.m.s. value) of an alternating quantity. i.e.,
Ka =
For sinusoidal alternating current,
Ka = = = 1.414
For sinusoidal alternating voltage,
Ka = = 1.414
The knowledge of Crest Factor is particularly important in the testing of dielectric strength
of insulating materials; this is because the breakdown of insulating materials depends upon the
maximum value of voltage.
Phase
An alternating voltage or current changes in magnitude and direction at every instant. So, it is
necessary to know the condition of the alternating quantity at a particular instant. The location of
the condition of the alternating quantity at any particular instant is called its phase.

We may define the phase of an alternating quantity at any particular instant as the
fractional part of a period or cycle through which the quantity has advanced from the
selected origin.
Taking an example, the phase of current at point A (+ve maximum value) is T/4 second, where
T is the time period, or expressed in terms of angle, it is π/2 radians (Fig.3.7). In other words, it
means that the condition of the wave, after having advanced through π/2 radians (900) from the
selected origin (i.e.,0) is that it is maximum value (in the positive direction).similarly, -ve
maximum value is reached after 3π/2 radians (2700) from the origin, and the phase of the current
at point B is 3T/4 second.
Phase Difference (Lagging or Leading of Sinusoidal wave)
When two alternating quantities, say, two voltages or two currents or one voltage and one
current are considered simultaneously, the frequency being the same, they may not pass through
a particular point at the same instant.
One may pass through its maximum value at the instant when the other passes through a
value other than its maximum one. These two quantities are said to have a phase difference.
Phase difference is specified either in degrees or in radians.
The phase difference is measured by the angular difference between the points where the
two curves cross the base or reference line in the same direction.
The quantity ahead in phase is said to lead the other quantity, whereas the second quantity
is said to lag behind the first one. In Fig.3.8, current I1, represented by vector 0A, leads the
current I2, represented by vector 0B, by , or current I2 lags behind the current I1 by .

The leading current I1 goes through its zero and maximum values first and the current I2 goes
through its zero and maximum values after time angle . The two waves representing these two
currents are shown in Fig.3.8. if I1 is taken as reference vector, two currents are expressed as
i1 = I1m sin ωt and i2 = I2m sin (ωt- )
The two quantities are said to be in phase with each other if they pass through zero values
at the same instant and rise in the same direction, as shown in Fig.3.9. However, if the two
quantities pass through zero values at the same instant but rise in opposite, as shown in Fig.3.10,
they are said to be in phase opposition i.e., the phase difference is 1800. When the two alternating
quantities have a phase difference of 900 or π/2 radians they are said to be in quadrature.
Phasor Representation of Alternating Quantities
We know that an alternating voltage or current has sine waveform, and generators are
designed to give e.m.f.s. with the sine waveforms. The method of representing alternating
quantities continuously by equation giving instantaneous values (like e = Em sin ωt) is quite

tedious. So, it is more convenient to represent a sinusoidal quantity by a phasor rotating in an

anticlockwise direction (Fig.3.12).
While representing an alternating quantity by a phasor, the following points are to be kept in
mind:
i) The length of the phasor should be equal to the maximum value of the alternating
quantity.
ii) The phasor should be in the horizontal position at the alternating quantity is zero and is
increasing in the positive direction.
iii) The inclination of the line with respect to some axis of reference gives the direction of
that quantity and an arrow-head placed at one end indicates the direction in which that
quantity acts.
iv) The angular velocity in an anti-clockwise direction of the phasor should be such that it
completes one revolution in the same time as taken by the alternating quantity to
complete one cycle.
Consider phasor 0A, which represents the maximum value of the alternating e.m.f. and its
angle with the horizontal axis gives its phase (Fig.3.12). now, it will be seen that the projection
of this phasor 0A on the vertical axis will give the instantaneous value of e.m.f.
0B = 0A sin ωt
Or e = 0A sin wt
= Em sin ωt
Note: The term „phasor‟ is also known as „vector‟.
a) 8+j6= < 0.75=10<36.90

b) -10-j7.5= < 0.75
= 12.5 < 0.75

This vector also falls in the third quadrant, so, following the same reasoning as mentioned
in method 1, the angle when measured in CCW direction is
= (1800+ 0.75)
= 1800+36.90=216.90
Measured in CCW direct from + ve co-ordinate of x-axis, the angle is
- (3600 – 216.90) = - 143.10
So this expression is written as 12.5 <-143.10
So, expression (ii) is rewritten as
10 < 36.90×12.5 <-143.10
125 <-106.20 which is the same as before.
A.C. circuits
The path for the flow of alternating current is called on a.c. circuit.
In a d.c. circuit, the current/flowing through the circuit is given by the simple relation I = .
However, in an a.c. circuit, voltage and current change from instant to instant and so give rise to
magnetic (inductive) and electrostatic (capacitive) effects. So, in an a.c. circuit, inductance and
capacitance must be considered in addition to resistance.
We shall now deal with the following a.c. circuits:
i) AC circuit containing pure ohmic resistance only.

ii) AC circuit containing pure inductance only.
iii) AC circuit containing pure capacitance only.
AC circuit containing pure ohmic Resistance
When an alternating voltage is applied across a pure ohmic resistance, electrons (current)
flow in one direction during the first half-cycle and in the opposite direction during the next half-
cycle, thus constituting alternating current in the circuit.

Let us consider an a.c. circuit with just a pure resistance R only, as shown in Fig.3.31.
Let the applied voltage be given by the equation
= Vm sin = Vm sin t --- (i)
As a result of this alternating voltage, alternating current „i‟ will flow through the circuit.
The applied voltage has to supply the drop in the resistance, i.e.,
= iR
Substituting the value of „ ‟ from eqn. (i), we get
Vm sin t = iR or i= sin t --- (ii)
The value of the alternating current „i‟ is maximum when sin t = 1,
i.e.,
Eqn.(ii) becomes,
i= sin t --- (iii)
From eqns.(i) and (ii), it is apparent that voltage and current are in phase with each other. This
is also indicated by the wave and vector diagram shown in Fig. 3.32.
Power: The voltage and current are changing at every instant.
Instantaneous power, P= Vm sin t. =

= .cos 2
Thus instantaneous power consists of a constant part and a
Fluctuating part cos 2 of frequency double that of voltage and current waves.
The average value of cos 2 over a complete cycle is zero.
So, power for the complete cycle is
P= =
or P = V1 watts
Where V = r.m.s. value of applied voltage
I = r.m.s. value of the current
Power curve
The power curve for a purely resistive circuit is shown in Fig. 3.33. It is apparent that power
in such a circuit is zero only at the instants a,b and c, when both voltage and current are zero, but
is positive at all other instants. in other words, power is never negative, so that power is always
lost in a resistive a.c. circuit. This power is dissipated as heat.

A.C. circuit containing pure Inductance
An inductive coil is a coil with or without an iron core and has negligible resistance. In
practice, pure inductance can never be had as the inductive coil has always a small resistance.
However, a coil of thick copper wire wound on a laminated iron core has negligible resistance,
so, for the purpose of our study, we will consider a purely inductive coil.
On the application of an alternating voltage (Fig.3.34) to a circuit containing a pure inductance, a

back e.m.f. is produced due to the self-inductance of the coil. This back e.m.f. opposes the rise or
fall o f current, at every stage. Because of the absence of voltage drop, the applied voltage has to
overcome this self-induced e.m.f. only.
Inductive Reactance: L in the expression Im = is known as inductive reactance and is

denoted by , i.e., = L. If „L‟ is in henry and „ ‟ is in radians per second, then will be
in ohms. So, inductive reactance plays the part the part of resistance.
Power: Instantaneous Power,
P = ×i= . Im sin
=- cos
The power measured by a wattmeter is the average value of „p‟, which is zero since average
of a sinusoidal quantity of double frequency over a complete cycle is zero. Put in mathematical
terms,
Power for the whole cycle, P = - dt = 0

Hence, power absorbed in a pure inductive circuit is zero.
Power curve
The power curve for a pure inductive circuit is shown in Fig. 3.36. This indicates that power
absorbed in the circuit is zero. At the instants a,c and e, voltage is zero, so that power is zero: it is
also zero at points b and d when the current is zero. Between a and b voltage and current are in
opposite directions, so that power is negative and energy is taken from the circuit. Between b and
c voltage and current are in the same direction, so that power is positive and is put back into the
circuit. Similarly, between c and d, power is taken from the circuit and between d and e it is put
into the circuit. Hence, net power is zero.
AC circuit containing pure capacitance
When an alternating voltage is applied across the plates of a capacitor, the capacitor is
charged in one direction and then in the opposite direction as the voltage reverses. With
reference to Fig. 3.38,
Let alternating voltage represented by = be applied across a capacitor of

capacitance C Farads.
Instantaneous charge, q = c = CVm sin
Capacitor current is equal to the rate of change of charge, or

i= (CVm sin )
= CVm cos
or i= sin
The current is maximum when t = 0
Im =
Substituting = Im in the above expression for instantaneous current, we get
i = Im sin
Capacitive Reactance: in the expression Im = is known as capacitive reactance and is
denoted by Xc.
i.e., Xc =
If C is farads and „ ‟ is in radians, then Xc will be in ohms.
It is seen that if the applied voltage is given by = , then the current is given by i =
Im sin this shows that the current in a pure capacitor leads its voltage by a quarter
cycle as shown in Fig. 3.39, or phase difference between its voltage and current is with the
current leading.

Power: Instantaneous Power,
P= i
= t. Im sin
= Im sin t cos t
= Im
Power for the complete cycle
= Im dt = 0
Hence power absorbed in a capacitive circuit is zero.
Power curves (Fig. 3.40)
At the instants b,d, the current is zero, so that power is zero; it is also zero at the instants
a,c and e, when the voltage is zero. Between a and b, voltage and current are in the same
direction, so that power is positive and is being put back in the circuit. Between b and c, voltage
and current are in the opposite directions, so that power is negative and energy is taken from the
circuit. Similarly, between c and d, power is put back into the circuit, and between d and e it is
taken from the circuit.
Therefore, power absorbed in a pure capacitive circuit is zero.

Series R-L circuit
Let us consider an a.c. circuit containing a pure resistance R ohms and a pure inductance of L
henrys, as shown in Fig. 3.43.
Let V = r.m.s. value of the applied voltage
I = r.m.s. value of the current
Voltage drop across R, VR = IR (in phase with I)
Voltage drop across L, VL = IXL (leading I by 900)
The voltage drops across these two circuit components are shown in Fig. 3.44, where vector OA
indicates VR and AB indicates VL. The applied voltage V is the vector sum of the two, i.e., OB.
V= =
=I
I=
The term offers opposition to current flow and is called the impedance (Z) of the
circuit. It is measured in ohms.
I=
Referring to the impedance triangle ABC, (Fig. 3.45)
or (impedance)2 + (reactance)2

Referring back to Fig. 3.44, we observe that the
applied voltage V leads the current I by an angle .
tan =
The same feature is shown by means of waveforms (Fig. 3.46). We observe that circuit
current lags behind applied voltage by an angle .
So, if applied voltage is expressed as = t, the current is given by i = Im( t - ),

Where Im = .
Definition of Real power, Reactive Power, Apparent power and power Factor
Let a series R-L circuit draw a current I (r.m.s. value) when an alternating voltage of r.m.s.
value V is applied to it. Suppose the current lags behind the applied voltage by an angle as
shown in Fig. 3.47.
Power Factor and its signifies
Power Factor may be defined as the cosine of the angle of lead or lag. In Fig. 3.47, the angle
of lag is shown.
Thus power Factor = cos .
In addition to having a numerical value, the power factor of a circuit carries a notation that
signifies the nature of the circuit, i.e., whether the equivalent circuit is resistive, inductive or
capacitive. Thus, the p.f. might be expressed as 0.8 lagging. The lagging and leading refers to the
phase of the current vector with respect to the voltage vector. Thus, a lagging power factor

means that the current lags the voltage and the circuit is inductive in nature. However, in the case
of leading power factor, the current leads the voltage and the circuit is capacitive.
Apparent Power: The product of r.m.s. values of current and voltage, VI, is called the apparent
power and is measured in volt-amperes (VA) or in kilo-volt amperes (KVA).
Real Power: The real power in an a.c. circuit is obtained by multiplying the apparent power by
the factor and is expressed in watts or killo-watts (kW).
Real power (W) = volt-amperes (VA) × power factor cos
or Watts = VA cos
Here, it should be noted that power consumed is due to ohmic resistance only as a pure
inductance does not consume any power.
Thus, P = V I cos
cos = (refer to the impedance triangle of Fig. 3.45)
P=VI×
= × IR = I2R
or P = I2R watts
Reactive Power: It is the power developed in the inductive reactance of the circuit. The
quantity VI sin is called the reactive power; it is measured in reactive volt-amperes or vars
(VAr).
The power consumed can be represented by means of waveform in Fig. 3.48.
We will now calculate power in terms of instantaneous values.
Instantaneous power, P = vi = Vm sin t × Im sin ( t - )
= Vm Im sin t sin( t- )
= Vm Im [cos - cos(2 t- )]

This power consists of two parts:
i) Constant part Vm Im cos which contributes to real power.

ii) Sinusoidally varying part Vm Im cos (2 t- ), whose frequency is twice that of the
voltage and the current, and whose average value over a complete cycle is zero (so it
does not contribute to any power).
So, average power consumed, P = Vm Im cos
= cos
= V I cos
Where V and I are r.m.s. values
Power curves:
The power curve for R-L series circuit is shown in Fig. 3.48. The curve indicates that the greater
part is positive and the smaller part is negative, so that the net power over the cycle is positive.
During the time interval a to b, applied voltage and current are in opposite directions, so that
power is negative. Under such conditions, the inductance L returns power to the circuit. During
the period b to c, the applied voltage and current are in the same direction so that power is
positive , and therefore, power is put into the circuit. In a similar way, during the period c to d,
inductance L returns power to the circuit while between d and e, power is put into the circuit.
The power absorbed by resistance R is converted into heat and not returned.

Series R – C circuit
Consider an a.c. circuit containing resistance R ohms and capacitance C farads, as shown in
the fig. 3.52(a).
Let V = r.m.s. value of voltage

I = r.m.s. value of current
voltage drop across R, VR = IR - in phase with I

Voltage drop across C, VC = IXC - lagging I by
The capacitive resistance is negative, so VC is in the negative direction of Y – axis, as shown
in the fig. 3.52(b).
We have V=
Or I=
The denominator, Z is the impedance of the circuit, i.e., Z = fig. 3.52(c) depicts
the impedance triangle.
Power factor, cos =

Fig. 3.52(b) shows that I leads V by an
angle , so that tan =
This implies that if the alternating voltage is v = Vm sin t, the resultant current in the R – C
circuit is given by
i = Im sin( t + ), such that current leads the applied voltage by the angle . The waveforms of
fig. 3.53 depict this.

Power: Average power, P = v × I = VI cos (as in sec. 3.17).
Power curves: The power curve for R – C series circuit is shown in fig. 3.54. The curve
indicates that the greater part is positive and the smaller part is negative, so that the net power is
positive.
Resistance, Inductance and capacitance in series (RLC – Series Circuit)
Consider an a.c. series circuit containing resistance R ohms, Inductance L henries and
capacitance C farads, as shown in the fig. 3.59.

Let V = r.m.s. value of applied voltage

I = r.m.s. value of current
Voltage drop across R, VR = IR - in phase with I

voltage drop across L, VL = I.XL - lagging I by 900
Voltage drop across C, VC = IXC - lagging I by 900
Referring to the voltage triangle of Fig. 3.60, OA represents VR, AB and AC represent inductive
and capacitive drops respectively. We observe that VL and VC are 1800 out of phase.
Thus, the net reactive drop across the combination is

AD = AB – AC
= AB – BD (∵ BD = AC)
= VL – VC
= I (XL - XC)
OD, which represents the applied voltage V, is the vector sum of OA and AD.
OD = OR V =
Or I = =
The denominator is the impendence of the circuit.

So (impedance)2 = (resistance)2 + (net reactance)2

Or Z2 = R2 + = R2 + X2
Where the net reactance = X (fig. 3.61)
Phase angle is given by
tan =
power factor,
cos =
Power = VI cos
If applied voltage is represented by the equation v = Vm sin t, then the resulting current in an
R – L – C circuit is given by the equation
i = Im sin( t )
If XC > XL , then the current leads and the +ve sign is to be used in the above equation.
If XL > XC, then the current lags and the –ve sign is to be used.
If any case, the current leads or lags the supply voltage by an angle , so that tan = .
If we employ the j operator (fig. 3.62), then we have

Z = R + j (XL - XC)
The value of the impedance is
Z=
The phase angle = tan-1
Z =Z tan-1
= Z tan-1
Parallel AC circuits
In a parallel a.c. circuit, the voltage across each branch of the circuit is the same whereas
current in each branch depends upon the branch impedance. Since alternating currents are vector
quantities, total line current is the vector sum of branch currents.
The following are the three methods of solving parallel a.c. circuits:
a) Vector method.
b) Admittance method.

c) Symbolic or j- method.
3.20.1 Vector method

In this method the total line current is found by drawing the vector diagram of the circuit.
As voltage is common, it is taken as the reference vector and the various branch currents are
represented vectorially. The total line current can be determined from the vector diagram either
by the parallelogram method or by the method of components.
Branch 1
Impedance Z1 =
Current I1 =
Cos 1= or 1 = cos-1
Current I1 lags behind the applied voltage by (fig. 3.65).

Branch 2
Impedance Z2 =
Current I2 =
Cos 2= or 2 = cos-1
Current I2 leads V by 2 (fig. 3.65).

Resultant current : The total line current I is the vector sum of the branch currents I1 and I2 and
is found by using the parallelogram law of vectors, as shown in fig. 3.65.
The second method is the method of components i.e., resolving the branch currents I1 and I2
along the x- axis and y- axis and then finding the resultant of these components (fig. 3.66).
Let the resultant current be I and be its phase angle, as shown in fig. 3.66 (b). Then the
components of I along X- axis is equal to the algebraic sum of the components of branch currents
I1 and I2 along the X- axis (active components).

Similarly, the component of I along Y- axis is equal to the algebraic sum of the components of I1
and I2 along Y- axis i.e,
Component of resultant current along Y- axis
= algebraic sum of I1 and I2 along X – axis
or I cos = I1 cos 1 + I2 cos 2
Component of resultant current along Y – axis

= algebraic sum of I1 and I2 along Y – axis
or I sin = I1 sin 1 – I2 sin 2
I=
and tan =
If tan is positive, current leads and if tan is negative, then the current lags behind applied
voltage V. power factor for the entire circuit
Cos =
Admittance Method
The reciprocal of impedance of a circuit is called its admittance. It is represented by Y.
Y=
So, Y =
Its unit is Siemens (S). A circuit with an impedance of one ohm has an admittance of one siemen.
Earlier, the unit of admittance was mho.

Just as impedance Z of a circuit had two rectangular components, resistance R and reactance X,
admittance Y also has two rectangular components known as conductance g and susceptance b.
fig. 3.67 shows the impendence triangle and the admittance triangle. It is clear the admittance has
two components g and b. The component g along the X- axis is the conductance which is the
reciprocal of resistance. The component b is called susceptance, which is the reciprocal of
reactance.
In fig. 3.67(a), the impedance and admittance triangles for an inductive circuit are shown.
It is apparent that susceptance b is negative, being below X – axis. Hence inductive susceptance
is negative. In fig. 3.67 (b), the impedance and admittance triangles for capacitive circuit is
shown. It is evident that susceptance is positive, being above the X – axis; hence, capacitive
susceptance is positive.
Relations
Conductance g = Y cos
Or g=
Conductance is always positive.
Susceptance b = Y sin =

Susceptance b is positive if reactance X is capacitive and negative if reactance is inductive.

Admittance Y =
The units of g, b and y are in Siemens.
Application of admittance method

Let us consider a parallel circuit with three branches, as given in fig. 3.68.
we can determine the conductors by just adding the conductance of the three branches. In a like
manner, susceptance is determined by the algebraic addition of the susceptances of the different
branches.
Total conductance,
G = g1 + g2 + g3
Total susceptance
B = (-b1) + (-b2) + b3
Total admittance Y =
Total current I = VY
Power factor, cos =
Symbolic or j- method
Let us take the parallel two – branch circuit of fig. 3.69, with the same p.d. across the
two impedances Z1 and Z2.
I1 = and I2 =
Total current I = I1 + I2 = =V

= V (Y1 + Y2)
= VY
Where the total admittance Y = Y1 + Y2
We should note that admittances are added for parallel branches, whereas impedances are added
for series branches. Both admittances and impedances are complex quantities, so all additions
have to be performed in complex form.
In case of the two parallel branches of fig. 3.70,
Y1 = =
Where g1 = ---- conductance of top branch
b1 = ----- susceptance of top branch

In similar manner,
Y2 = =
Total admittance Y = Y1 + Y2
=
= (g1 + g2) – j(b1 – b2)
= G – JB
Y=
= tan-1
0
In polar form, admittance Y = Y
Y= tan-1
Total current I = VY; I1 = VY1 and I2 VY2

V = V 00 and Y = Y
So I = VY = V 00 × Y = VY
Taking a general case,
V=V and Y = Y , then
So I = VY = V ×Y = VY +

3b. Domestic Wiring:

Introduction
A network of wires drawn connecting the meter board to the various energy consuming loads
(lamps, fans, motors etc) through control and protective devices for efficient distribution of
power is known as electrical wiring.
Electrical wiring done in residential and commercial buildings to provide power for lights, fans,
pumps and other domestic appliances is known as domestic wiring. There are several wiring
systems in practice. They can be classified into:
Types of wiring: Depending upon the above factors various types of wiring used in practice are:
1. Cleat wiring
2. Casing wiring
3. Surface wiring
4. Conduit wiring
i ) Clear wiring:
In this type V.I.R or P.V.C wires are clamped between porcelain cleats.

The cleats are made up of two halves. One half is grooved through which wire passes while
the other fits over the first. The whole assembly is then mounted on the wall or wooden beam
with the help of screws.
This method is one of the cheapest method and most suitable for temporary work. It can be
very quickly installed and can be recovered without any damage of material. Inspection and
changes can be made very easily.
This method does not give attractive appearance. After some time due to sagging at some
places, it looks shabby. Dust and dirt collects on the cleats. The wires are directly exposed to
atmospheric conditions like moisture, chemical fumes etc. maintenance cost is very high.
Due to these disadvantages this type is not suitable for permanent jobs.
ii) Casing capping: This is very popularly used for residential buildings. In this method,
casing is a rectangular strip made from teak wood or new a day‟s made up of P.V.C. It has two
grooves into which the wires are laid. Then casing is covered with a rectangular strip of wood or
P.V.C. of the same width, called capping. The capping is screwed into casing is fixed to the walls
the help or porcelain discs or cleats.
Good protection to the conductors from dangerous atmospheric conditions, neat and clean
appearance are the advantages of this type.
In case of wooden casing capping, there is high risk of fire along with the requirement of skilled
labour. The method is costly.

Surface wiring: in this type, the wooden battens are fixed on the surface of the wall, by
means of screws and rawl plugs. The metal clips are provided with the battens at regular
intervals. The wire runs on the batten and is clamped on the batten using the metal clips. The
wires used may lead sheathed wires or can tyre sheathed wires. Depending upon type of wire
used surface wiring is also called lead sheathed wiring or cab tyre sheathed wiring. If the wire
used is though rubber Sheathed then it is called T.R.S. wiring while if the wire used is cab tyre
Sheathed Then it is called C.T.S wiring.
Conduit wiring: In this method, metallic tubes called as conduits are used to run the wires.
This is the best system of wiring as it gives full mechanical protection to the wires. This is most
desirable for workshops and public Buildings. Depending on whether the conduits are laid inside
the walls or supported on the walls, there are two types of conduit wiring which are :

i) Surface conduit wiring: in this method conduits are mounted or supported on the walls
with the help of pipe books or saddles. In damp situations, the conduits are spaced apart from
the wall by means of wooden blocks.
ii) Concealed conduit wiring: In this method, the conduit are buried under the wall at the
some of plastering. This is also called recessed conduit wiring.
The beauty of the premises is maintained due to conduit wiring. It is durable and has long
life. It protects the wires from mechanical shocks and fire hazards. Proper earthing of
conduits makes the method electrical shock proof. It requires very less maintenance.
The repairs are very difficult in case of concealed conduit wiring. This method is most
costly and erection requires highly skilled labour. These are few disadvantages of the
conduit type of wiring. In concealed conduit wiring, keeping conduit at earth potential is
must.
FACTORS AFFECTING THE CHOICE OF WIRING SYSTEM:
The choice of wiring system for a particular installation depends on technical factors and
economic viability.
1. Durability: Type of wiring selected should conform to standard specifications, so that it is

durable i.e. without being affected by the weather conditions, fumes etc.
2. Safety: The wiring must provide safety against leakage, shock and fire hazards for the
operating personnel.
3. Appearance: Electrical wiring should give an aesthetic appeal to the interiors.

4. Cost: It should not be prohibitively expensive.
5. Accessibility: The switches and plug points provided should be easily accessible. There must
be provision for further extension of the wiring system, if necessary.
6 Maintenance Cost: The maintenance cost should be a minimum
7. Mechanical safety: The wiring must be protected against any mechanical damage
Specification of Wires:
The conductor material, insulation, size and the number of cores, specifies the electrical wires.
These are important parameters as they determine the current and voltage handling capability of
the wires. The conductors are usually of either copper or aluminum. Various insulating materials
like PVC, TRS, and VIR are used. The wires may be of single strand or multi strand. Wires with
combination of different diameters and the number of cores or strands are available.
For example: The VIR conductors are specified as 1/20, 3/22,….7/20 ………
The numerator indicates the number of strands while the denominator corresponds to the
diameter of the wire in SWG (Standard Wire Gauge). SWG 20 corresponds to a wire of
diameter 0.914mm, while SWG 22 corresponds to a wire of diameter 0.737 mm.
A 7/0 wire means, it is a 7-cored wire of diameter 12.7mm (0.5 inch). The selection of the wire
is made depending on the requirement considering factors like current and voltage ratings, cost
and application.
Example: Application: domestic wiring
1. Lighting - 3/20 copper wire

2. Heating - 7/20 copper wire
The enamel coating (on the individual strands) mutually insulates the strands and the wire on the
whole is provided with PVC insulation. The current carrying capacity depends on the total area
of the wire. If cost is the criteria then aluminum conductors are preferred. In that case, for the
same current rating much larger diameter of wire is to be used.

Two- way and Three- way Control of Lamps:
The domestic lighting circuits are quite simple and they are usually controlled from one point.
But in certain cases it might be necessary to control a single lamp from more than one point
(Two or Three different points).
For example: staircases, long corridors, large halls etc.
Two-way Control of lamp:
Two-way control is usually used for staircase lighting. The lamp can be controlled from two
different points: one at the top and the other at the bottom - using two- way switches which strap
wires interconnect. They are also used in bedrooms, big halls and large corridors. The circuit is
shown in the following figure.
Switches S1 and S2 are two-way switches with a pair of terminals 1&2, and 3&4 respectively.
When the switch S1 is in position1 and switch S2 is in position 4, the circuit does not form a
closed loop and there is no path for the current to flow and hence the lamp will be OFF. When
S1 is changed to position 2 the circuit gets completed and hence the lamp glows or is ON. Now if
S2 is changed to position 3 with S1 at position 2 the circuit continuity is broken and the lamp is
off. Thus the lamp can be controlled from two different points.

Position of S1 Position of S2 Condition of lamp
1 3 ON
1 4 OFF
2 3 OFF
2 4 ON
Three- way Control of lamp:
In case of very long corridors it may be necessary to control the lamp from 3 different points. In
such cases, the circuit connection requires two; two-way switches S1and S2 and an intermediate
switch S3. An intermediate switch is a combination of two, two way switches coupled together. It
has 4 terminals ABCD. It can be connected in two ways
a) Straight connection
b) Cross connection
In case of straight connection, the terminals or points AB and CD are connected as shown in
figure 1(a) while in case of cross connection, the terminals AB and
C D is connected as shown in figure 1(b). As explained in two –way control the lamp is ON if
the circuit is complete and is OFF if the circuit does not form a closed loop.

The condition of the lamp is given in the table depending on the positions of the switches S1, S2
and S3.

EARTHING:
The potential of the earth is considered to be at zero for all practical purposes as the generator
(supply) neutral is always earthed. The body of any electrical equipment is connected to the earth
by means of a wire of negligible resistance to safely discharge electric energy, which may be due
to failure of the insulation, line coming in contact with the casing etc. Earthing brings the
potential of the body of the equipment to ZERO i.e. to the earth‟s potential, thus protecting the
operating personnel against electrical shock. The body of the electrical equipment is not
connected to the supply neutral because due to long transmission lines and intermediate
substations, the same neutral wire of the generator will not be available at the load end. Even if
the same neutral wire is running it will have a self-resistance, which is higher than the human
body resistance. Hence, the body of the electrical equipment is connected to earth only.
Thus earthing is to connect any electrical equipment to earth with a very low resistance wire,
making it to attain earth‟s potential. The wire is usually connected to a copper plate placed at a
depth of 2.5 to 3meters from the ground level.
BLOCK DIAGRAM
The earth resistance is affected by the following factors:
1. Material properties of the earth wire and the electrode

2. Temperature and moisture content of the soil
3. Depth of the pit
4. Quantity of the charcoal used

The importance of earthing is illustrated in the following figures


 Necessity of Earthing:
1. To protect the operating personnel from danger of shock in case they come in contact
with the charged frame due to defective insulation.
2. To maintain the line voltage constant under unbalanced load condition.
3. Protection of the equipments
4. Protection of large buildings and all machines fed from overhead lines against lightning.

 Methods of Earthing:
The important methods of earthing are the plate earthing and the pipe earthing. The earth
resistance for copper wire is 1 ohm and that of G I wire less than 3 ohms. The earth resistance
should be kept as low as possible so that the neutral of any electrical system, which is earthed, is
maintained almost at the earth potential. The typical value of the earth resistance at powerhouse
is 0. 5 ohm and that at substation is 1 ohm.
1. Plate earthing 2. Pipe earthing

Plate Earthing
In this method a copper plate of 60cm x 60cm x 3.18cm or a GI plate of the size 60cm x 60cm x
6.35cm is used for earthing. The plate is placed vertically down inside the ground at a depth of
3m and is embedded in alternate layers of coal and salt for a thickness of 15 cm. In addition,
water is poured for keeping the earth electrode resistance value well below a maximum of 5
ohms. The earth wire is securely bolted to the earth plate. A cement masonry chamber is built
with a cast iron cover for easy regular maintenance.
Pipe Earthing
Earth electrode made of a GI (galvanized) iron pipe of 38mm in diameter and length of 2m
(depending on the current) with 12mm holes on the surface is placed upright at a depth of 4.75m

in a permanently wet ground. To keep the value of the earth resistance at the desired level, the
area (15 cms) surrounding the GI pipe is filled with a mixture of salt and coal.. The efficiency of
the earthing system is improved by pouring water through the funnel periodically. The GI earth
wires of sufficient cross- sectional area are run through a 12.7mm diameter pipe (at 60cms
below) from the 19mm diameter pipe and secured tightly at the top as shown in the following
figure.
When compared to the plate earth system the pipe earth system can carry larger leakage currents
as a much larger surface area is in contact with the soil for a given electrode size. The system
also enables easy maintenance as the earth wire connection is housed at the ground level.

PROTECTIVE DEVICES
Protection for electrical installation must be provided in the event of faults such as short circuit,
overload and earth faults. The protective circuit or device must be fast acting and isolate the faulty
part of the circuit immediately. It also helps in isolating only required part of the circuit without
affecting the remaining circuit during maintenance. The following devices are usually used to
provide the necessary protection:
 Fuses
 Relays
 Miniature circuit breakers (MCB)
 Earth leakage circuit breakers (ELCB)
FUSE
The electrical equipment‟s are designed to carry a particular rated value of current under normal
circumstances. Under abnormal conditions such as short circuit, overload or any fault the current
raises above this value, damaging the equipment and sometimes resulting in fire hazard. Fuses
are pressed into operation under such situations. Fuse is a safety device used in any electrical
installation, which forms the weakest link between the supply and the load. It is a short length of
wire made of lead / tin /alloy of lead and tin/ zinc having a low melting point and low ohmic
losses. Under normal operating conditions it is designed to carry the full load current. If the
current increases beyond this designed value due any of the reasons mentioned above, the fuse
melts (said to be blown) isolating the power supply from the load as shown in the following
figures.

CHARACTERISTICS OF FUSE MATERIAL

The material used for fuse wires must have the following characteristics
1. Low melting point

2. Low ohmic losses
3. High conductivity
4. Lower rate of deterioration

Different types of fuses:

Re-wirable or kit -kat fuses: These fuses are simple in construction, cheap and available
up-to a current rating of 200A. They are erratic in operation and their performance deteriorates
with time.
Plug fuse: The fuse carrier is provided with a glass window for visual inspection of the
fuse wire.
Cartridge fuse: Fuse wire usually an alloy of lead is enclosed in a strong fiber casing.
The fuse element is fastened to copper caps at the ends of the casing. They are available up-to a
voltage rating of 25kV. They are used for protection in lighting installations and power lines.
Miniature Cartridge fuses: These are the miniature version of the higher rating
cartridge fuses, which are extensively used in automobiles, TV sets, and other electronic
equipment‟s.
Transformer fuse blocks: These porcelain housed fuses are placed on secondary of the
distribution transformers for protection against short circuits and overloads.
Expulsion fuses: These consist of fuse wire placed in hollow tube of fiber lined with
asbestos. These are suited only for out door use for example, protection of high voltage circuits.
Semi-enclosed re-wirable fuses: These have limited use because of low breaking
capacity.
Time-delay fuse: These are specially designed to withstand a current overload for a
limited time and find application in motor circuits.

HRC CARTRIDGE FUSE:
The high rupturing capacity or (HRC) fuse consists of a heat resistant ceramic body. Then silver
or bimetallic fuse element is welded to the end brass caps. The space surrounding the fuse
element is filled with quartz powder. This filler material absorbs the arc energy and extinguishes
it. When the current exceeds the rated value the element melts and vaporizes. The vaporized
silver fuses with the quartz and offers a high resistance and the arc is extinguished.
Advantages:
1. Fast acting
2. Highly reliable
3. Relatively cheaper in comparison to other high current interrupting device
Disadvantages:
1. Requires replacement
2. The associated high temperature rise will affect the performance of other devices
TERMS RELATED WITH FUSES:

Rated current: It is the maximum current, which a fuse can carry without undue heating or
melting. It depends on the following factors:

1. Permissible temperature rise of the contacts of the fuse holder and the
fuse material
2. Degree of deterioration due to oxidation.
Fusing current: The minimum current at which the fuse melts is known as the fusing current.
It depends on the material characteristics, length, diameter, cross-sectional area of the fuse
element and the type of enclosure used.
Fusing Factor: It is the ratio of the minimum fusing current to the rated current. It is always
greater than unity.

MODULE – 4
4a. Three Phase Circuits:
Advantages of three phase system:
In the three phase system, the alternator armature has three windings and it produces three
independent alternating voltages. The magnitude and frequency of all of them is equal but they
have a phase difference of 1200 between each other. Such a three phase system has following
advantages over single phase system:
1) The output of three phase machine is always greater than single phase machine of same
size, approximately 1.5 times. So for a given size and voltage a three phase alternator
occupies less space and has less cost too than single phase having same rating.
2) For a transmission and distribution, three phase system needs less copper or less
conducting material than single phase system for given volt amperes and voltage rating so
transmission becomes very much economical.
3) It is possible to produce rotating magnetic field with stationary coils by using three phase
system. Hence three phase motors are self-starting.
4) In single phase system, the instantaneous power is a function of time and hence fluctuates
w.r.t. time. This fluctuating power causes considerable vibrations in single phase motors.
Hence performance of single phase motors is poor. While instantaneous power in
symmetrical three phase system is constant.
5) Three phase system give steady output.
6) Single phase supply can be obtained from three phase but three phase cannot be obtained
from single phase.
7) Power factor of single phase motors is poor than three phase motors of same rating.
8) For converting machines like rectifiers, the d.c. output voltage becomes smoother if
number of phases are increased.
But it is found that optimum number of phases required to get all above said advantages is
three. Any further increase in number of phases cause a lot of complications. Hence three phase
system is accepted as standard polyphase system throughout the world.

Generation of 3-phase E.M.F.
In the 3-phase system, there are three equal voltages of the same frequency but
displaced from one another by 1200 electrical. These voltages are produced by a three-phase
generator which has three identical windings or phases displaced 1200 electrical apart. When
these windings are rotated in a magnetic field, e.m.f. is induced in each winding or phase.
These e.m.f. s are of the same magnitude and frequency but are displaced from one another
by 1200 electrical.
Consider three electrical coils mounted on the same axis but

displaced from each other by 1200 electrical. Let the three coils be rotated in an anticlockwise
direction in a bipolar magnetic field with an angular velocity of radians/sec, as shown in
Fig. 3.80. Here, , are the start terminals and are the end terminals
of the coils.
When the coil is in the position AB shown in Fig. 3.80, the magnitude and direction
of the e.m.f. s induced in the various coils is as under:

a) E.m.f. induced in coil is zero and is increasing in the positive direction. This is
indicated by wave in Fig. 3.80 (b).
b) The coil is 1200 electrically behind coil the e.m.f. induced in this coil is
negative and is approaching maximum negative value. This is shown by the wave.
c) The coil is 2400 electrically behind or 1200 electrically behind coil . The
e.m.f. induced in this coil is positive and is decreasing. This is indicated by wave .
Thus, it is apparent that the e.m.f.‟s induced in the three coils are of the same magnitude
and frequency but displaced 1200 electrical from each other.
Vector Diagram: The r.m.s. values of the three phase voltage are shown vectorially in
Fig. 3.80(c).
Equations: The equations for the three voltages are:
= sin t
= sin ; = sin
Meaning of phase sequence
The order in which the voltages in the voltages in the phases reach their maximum positive
values is called the phase sequence. For example, in Fig. 3.80(a), the three coils , and
are rotating in anticlockwise direction in the magnetic field. The coil is 1200 electrical
ahead of coil and 2400 electrical ahead of coil . Therefore, e.m.f. in coil leads the
e.m.f. in coil by 1200 and that in coil by 2400. It is evident from Fig. 3.80(b) that
attains maximum positive first, then and . In other words, the order in which
the e.m.f. s in the three phases , and attain their maximum positive values is
a,b,c. Hence, the phase sequence is a,b,c.
Naming the phases
The 3 phases may be numbered (1,2,3) or lettered (a,b,c) or specified colours (R Y B). By
normal convention, sequence RYB is considered positive and R B Y negative.

Meaning of phase sequence
It is necessary to employ some systematic notation for the solution of a.c. circuits and systems
containing a number of e.m.f. s. acting and currents flowing so that the process of solution is
simplified and less prone to errors.
It is normally preferred to employ double-subscript notation while dealing with a.c. electrical
circuits. In this system, the order in which the subscripts are written indicates the direction in
which e.m.f. acts or current flows.
For example, if e.m.f. is expressed as

it indicates that e.m.f. acts from a to b; if it is
expressed as , then the e.m.f. acts in a direction
opposite to that in which acts. (Fig. 3.81)
i.e., =- .
Similarly, Iab indicates that current flows in the direction from a to b but Iba indicates that
current flows in the direction from b to a; i.e., Iba = -Iab.
Balanced Supply and Load
When a balanced generating supply, where the three phase voltages are equal, and the phase
difference is 1200 between one another, supplies balanced equipment load, where the impedance
of the three phases or three circuit loads are equal, then the current flowing through these three
phases will also be equal in magnitude, and will also have a phase difference of 120 0 with one
another. Such an arrangement is called a balanced load.
Obtaining Relationship between Line & Phase Values & Expression for power for
Balanced Star Connection
This system is obtained by joining together similar ends, either the start or the finish; the other
ends are joined to the line wires, as shown in Fig.3.82 (a). The common point N at which similar
(start or finish) ends are connected is called the neutral or star point. Normally, only three wires
are carried to the external circuit, giving a 3-phase, 3-wire, star-connected system; however,

sometimes a fourth wire known as neutral wire, is carried to the neutral point of the external
load circuit, giving a 3-phase, 4-wire connected system.
The voltage between any line and the neutral point, i.e., voltage across the phase winding, is
called the phase voltage; while the voltage between any two outers is called line voltage.
Usually, the neutral point is connected to earth. In Fig.3.82 (a), positive directions of e.m.f.s. are
taken star point outwards. The arrow heads on e.m.f.s. and currents indicate the positive
direction. Here, the 3-phases are numbered as usual: R,Y and B indicate the three natural colours
red, yellow and blue respectively. By convention, sequence RYB is taken as positive and RYB as
negative.
In Fig.3.82 (b), the e.m.f.s induced in the three phases, are shown vectorially. In a star-
connection there are two windings between each pair of outers and due to joining of similar ends
together, the e.m.f.s induced in them are in opposition.
Hence the potential difference between the two outers, know as line voltage, is the vector
difference of phase e.m.f.s of the two phases concerned.
For example, the potential difference between outers R and Y or
Line voltage ERY, is the vector difference of phase e.m.f.s ER and EY or vector sum of phase
e.m.f.s ER and (-EY).
i.e. ERY = ER- EY (vector difference)

or ERY = ER + (-EY) (vector sum)
as phase angle between vectors ER and (-EY) is 600,
from vector diagram shown in Fig.3.82(b),
ERY =
Let ER = EY = EB = EP (phase voltage)
Then line voltage ERy = = EP
Similarly, potential difference between outers Y and B or line. Voltage EYB = EY – EB =

EP and potential difference between outers B and R, or line voltage EBR = EB – ER = EP.
In a balanced star system, ERY, EYB and EBR are equal in magnitude and are called line
voltages.
EL = EP
Since, in a star-connected system, each line conductor is connected to a separate phase, so

the current flowing through the lines and phases are the same.
i.e. Line current IL = phase current IP
If the phase current has a phase difference of with the voltage,
Power output per phase = EPIP cos
Total power output, P = 3EPIP cos
=3 IP cos
= EL IL cos
i.e. power = x line voltage x line current x power factor
Apparent power of 3-phase star-connected system

= 3 x apparent power per phase
= 3EPIP = 3x x IL = EL IL
Obtaining Relationship between Line and Phase Values and Expression for Power for
Balanced Delta Connection
When the starting end of one coil is connection to the finishing end of another coil, as
shown in Fig.3.83 (a), delta or mesh connection is obtained. The direction of the e.m.f.s is as
shown in the diagram.
From Fig.3.83 it is clear that line current is the vector difference of phase currents of the
two phases concerned. For example, the line current in red outer IR will be equal to the vector
difference of phase currents IYR and IRB. The current vectors are shown in Fig.3.83 (b).
Referring to Fig.3.83 (a) and (b),
Line current, IR = IYR – IRB (vector difference)
= IYR + (-IRB) (vector sum)
As the phase angle between currents IYR and –IRB is 600
IR =
For a balanced load, the phase current in each winding is equal and let it be = IP.

Line current, IR = = IP
Similarly, line current, IY = IBY – IYR = IP
And line current, IB = IRB – IBY = IP
In a delta network, there is only one phase between any pair of line outers, so the potential
difference between the outers, called the line voltage, is equal to phase voltage.
i.e. Line voltage, EL = phase voltage, EP
Power output per phase = EPIP cos ,; where cos is the power factor of the load.
Total power output, P = 3EPIP cos
= 3EL cos
= ELIL cos
i.e. Total power output = x Line voltage x Line current x p.f.
Apparent power of 3-phase delta-connected system
= 3 x apparent power per phase
= 3 EPIP = 3EL ELIL
Show that in a three phase, balanced circuit, two wattmeters are sufficient to measure the
total three phase power and power factor of the circuit.
Two wattmeter method: The current coils of the two wattmeters are connected in any two lines
while the voltage coil of each wattmeters is connected between its own current coil terminal and
line without current coil. Consider star connected balanced load and two wattmeters connected as
shown in fig. 13. Let us consider the rms values of the currents and voltages to prove that sum of
two wattmeter gives total power consumed by three phase load.

VRB = VR VB ; VYB = VY VB ; VR^IR =

VR = VY = VB = Vph
VRB = VR VB , IR = IY = IL = Iph
VYB = VY VB = VRB = VL
From fig. 14, IR^VRB = 30 and IR^VRB = 30 +
W1 = IR VRB cos ( 30 ) = VL IL cos ( 30 )
W2= IY VYB cos ( 30 + ) = VL IL cos ( 30 + )
W1 + W2 = VL IL[ cos ( 30 ) + cos ( 30 + )]
= VLIL[cos 30 cos + sin 30 sin + cos 30 cos sin 30 sin ]
= 2VLIL cos30 cos = 2VLIL cos
= VLIL cos = total power
1. Each of the two wattmeters connected to measure the input to a three phase reads 20
kW. What does each instrument reads, when the load p.f. is 0.866 lagging with the total
three phase power remaining unchanged in the altered condition?
sol. : Each wattmeters reads 20 kW total power = 40 kW

As both wattmeters reads same cos =1 = 00
Now p.f. is 0.866 lag
Cos new = 0.866 new = 300

We have, = here = new
As the total power in 3ph circuit remains same W1 + W2 = 410 ------- (i)
300 =
= W1 W2
W1 W2 = 13.33
(i) + (ii) gives,
2W1 = 53.33
W1 = 26.66 kW
From (i), W2 = 40 W1 = 40 26.66 = 13.33
W2 = 13.33 kW
2) Three similar coils each having resistance of 10 ohm and reactance of 8 ohm are
connected in star across a 400 V, 3 phase supply. Determine the i) Line current; ii) Total
power and
iii) Reading of each of two wattmeters connected to measure the power.
Ans.: R=10 , = 8 , = 400 V, star

= 10 + j 8 = 12.082
= = = 230.94 V, …star
i) = = = 18.0334 V,
= = 18.0334 A.
ii) = cos where = 38.6590
= 400 18.0334 cos
= 9756.2116 W
iii) = cos (30- ) = 400 18.0334 cos ( - )
= 7131.1412 W
= cos (30+ ) = 400 18.0334 cos ( + )
= 2625.0704 W
4b. Three Phase Synchronous Generators:
Electric power is generated using three phase alternators.
Principle: Whenever a coil is rotated in a magnetic field an EMF will be induced in the coil.
This is called the dynamically induced EMF.

Alternators are also called as Synchronous Generators due to the reason that under normal
conditions the generator is to be rotated at a definite speed called “SYNCHRONOUS SPEED”,
Ns R.P.M. in order to have a fixed frequency in the output EMF wave.
Ns is related with the frequency as Ns = 120f / P, where f is the frequency and P is the total
number of poles.
The following table gives the idea of the various synchronous speeds for various numbers of
poles for the fixed frequency of 50 Hz.
P 2 4 6 8 10 12 16 ……….
Ns rpm 3000 1500 1000 750 600 500 375 ……….
Working principle of alternator :

The alternators work on the principle of electromagnetic induction. When there is a
relative motion between the conductors and the flux, e.m.f. gets induced in the conductors. The
d.c. generators also work on the same principle. The only difference in practical alternator and a
d.c. generator is that in an alternator the conductors are stationary and field is rotating. But for
understanding purpose we can always consider relative motion of conductors with respect to the
flux produced with respect to the flux produced by the field winding.
Consider a relative motion of a single conductor under the magnetic field produced by two
stationary poles. The magnetic axis of the two poles produced by field is vertical, shown dotted
in the fig. 34.

Let the conductor starts rotating from position 1. At this instant, the entire velocity component is
parallel to the flux lines. Hence there is no cutting of flux lines by the conductor. So at this
instant is zero and hence induced e.m.f. in the conductor is also zero.
As the conductor moves from position 1 to position 2, the part of the velocity
component becomes perpendicular to the flux lines and proportional to that e.m.f. increases as
the conductor moves from position 1 towards 2.
At position 2, the entire velocity component is perpendicular to the flux lines. Hence
there exists maximum cutting of the flux lines. And at this instant, the induced e.m.f. in the
conductor is at its maximum.
As the position of the conductor changes from 2 towards 3, the velocity component
perpendicular to the flux starts decreasing and hence induced e.m.f. magnitude also starts
decreasing. At position 3, again the entire velocity component is parallel to the flux lines and
hence at this instant induced e.m.f. in the conductor is zero.
As the conductor moves from position 3 towards 4, the velocity component
perpendicular to the flux lines again starts increasing. But the direction of velocity component
now is opposite to the direction of velocity component existing during the movement of the
conductor from position 1 to 2. Hence induced e.m.f. in the conductor increases but in the
opposite direction.
At the position 4, it achieves maxima in the opposite direction, as the entire velocity
component becomes perpendicular to the flux lines.
Again from position 4 to 1, induced e.m.f. decreases and finally at position 1,again becomes
zero. This cycle continues as conductor rotates at a certain speed.
So if we plot the magnitudes of the induced e.m.f. against the time, we get alternating nature of
the induced e.m.f. as shown in the fig. 34 (b).This is the working principle of an alternator.
TYPES AND THEIR CONSTRUCTION:
Their two basic parts in an alternator:
(i) Stator,
(ii) Rotor.
Stator is the stationary part and Rotor is the revolving part.

There are two possibilities that (i) The armature can be the stator and the field system can be the
rotor, and (ii) The armature can be the rotor and the field system be the stator. In practice large
alternators are of the first type where in the stator is the armature and the rotor is the field
system. And this type is called the “REVOLVING FIELD TYPE”.
Revolving field types are preferred due to the following reasons:
(i) More conductors can be easily accommodated and with these high voltage and higher
power capacity can be achieved.
(ii) Armature conductors can be easily braced over a rigid frame.
(iii) It is easier to insulate a stationary system.
(iv) Cooling of the conductors will be very effective with proper cooling ducts / vents in the
stationary part.
(iv) Power can be tapped easily without any risk from the stationary part through terminal
bushings.
(v) The armature conductors are totally free from any centrifugal force action which tends
to drag the conductors out of the slots.
CONSTRUCTION:
Revolving field type alternators are further classified into two types:
(i) Salient pole type,

(ii) (ii) Non-salient pole type or cylindrical rotor type.

Figs. (a), (b) and (c) shows the constructional features of the Alternator. Fig. (a) Represents
the stator, the core of which is made of steel laminations with slots cut in its inner periphery
and all the stator stampings are pressed together and are fixed to the stator frame. Three
phase windings are accommodated in these slots. These coils are identical to each other and
are physically distributed such that they are displaced from each other by 120 degrees as
shown in fig. (d).Fig. (b) Represents the structure of a salient pole rotor where the poles are
of projected type and are mounted on a spider and the field or the pole windings are wound
over the pole core as shown. This type is preferred where the running speeds are low. Fig.(c)
represents the structure of a non-salient pole rotor where the overall structure is like a
cylinder having 2 or 4 poles. This type is preferred where the running speeds are very high.
The armature windings in the stator are made of copper and are normally arranged in two
layers and are wound for lap or wave depending on the requirements and are usually
connected in star with the neutral terminal brought out.
EMF Equation:
Let P be the total number of poles, Ns be the synchronous speed, f be the frequency of the
induced EMF and the flux Φ considered to be sinusoidally distributed.

As we know that the induced emf is due to the rate of change of flux cut by coils, the average
induced emf in Tph number of turns is
Eavg = Tph dΦ / dt volts.
For a flux change from Φm to Φm is d Φ = 2 Φm in time dt= T / 2 seconds,
The average induced Emf = Tph. 2 Φ m / ( T/2 ) = 4 Tph .f. m volts.
For a sine wave we know that the form factor is of value 1.11= Erms / Eavg.
Therefore, Erms = 1.11.Eavg.
Erms = 4.44 f Φm Tph volts per phase. . . . . . . . . . .(1)
If the armature windings are connected in star the line emf is El = 3 Ephase.
If the armature windings are connected in delta the line emf is the phase emf itself.
Equation (1) represents the theoretical value of the induced emf in each phase but in practice
the Induced emf will be slightly less than the theoretical value due to the following reasons:
(i) The armature windings are distributed throughout the armature in various slots and
this is accounted by a factor called the “Distribution factor” Kd and is given by
Kd = (Sin(mα / 2) / mSin(α / 2)), where m is the number of slots per pole peer phase
and α is the slot angle.
α = 1800 / no. of slots per pole.
(ii) The span of the armature coil is less than a full pitch – This is done deliberately to
eliminate some unwanted harmonics in the emf wave, this fact is accounted by a factor called the
coil span factor or the pitch factor, Kp and is given by
Kp = Cos (β / 2), where β is the angle by which the coils are short chorded.
The modified Emf equation with these two factors taken into account will be
E = 4.44 Kd.Kp.f Tph volts per phase.

The product of Kd and Kp is called as the winding factor Kw .which is of value around 0.95.
VOLTAGE REGULATION:
The voltage regulation of an alternator is defined as the change in the terminal voltage between
no load and full load at a specified power factor, without any change in the speed and excitation.
(No load terminal voltage – Full load terminal voltage)
% Voltage regulation = --------------------------------------------------------------------- x 100
Full load terminal voltage
E–V
% Voltage regulation = -------- x 100
The idea of voltage regulation is necessary to judge the performance of an alternator.

Lesser the value of the regulation better will be the load sharing capacity at better efficiency.
1. A 3 phase, 6 pole, star connected alternator has 48 slots and 12 conductors per slot on the
armature. If the rotor at 1200RPM and the flux per pole is 0.3 Wb, calculate the e.m.f.
induced in the armature. The coils are full pitched and the winding factor is 0.95.
sol. : P = 6, slots = 48, conductors/ slots = 12, = 0.3 wb
Ns = Ns = 1200 rpm
f=
for full pitched winding, Kc = 1, Kd = 0.95
Total conductors = slots × conductors/slot = 48×12 = 576
Zph =
Tph =
Eph = 4.44 Kc Kd f Tph
Eph = 4.44×1×0.95×60×0.3×96

= 75.9 × 96
Eph = 7288.70 volts
Eline = 3 Eph = 3×7288.70
Eline = 12.624 Kv
Difference between salient and cylindrical type of rotor :
Salient pole type Smooth cylindrical type

1 Poles are projecting out from the Portion of the cylinder acts as poles
surface. hence poles are non-projecting.
2 Air gap is non uniform. Air gap is uniform due to smooth
cylindrical periphery.
3 Diameter is high and axial length is Small diameter and large axial length is
small. the feature.
4 Mechanically weak. Mechanically robust.
5 Preferred for low speed alternators. Preffered for high speed alternators i.e.
for tuboalternators.
6 Prime mover used is water turbines, I.C. Prime mover used are steam turbines,
engines. electric motors.
7 For same size, the rating is smaller than For same size, rating is higher than
cylindrical type. sailent pole type.
8 Separate damper winding is provided Separate damper winding is not
necessary.
Explain voltage regulation of an alternator and its significance.
Voltage regulation of an alternator:

Under the load condition, the terminal voltages of alternator is less than the induced e.m.f.
Eph. So if the load is disconnected, Vph will change from Vph to Eph, if flux and speed is
maintained constant. This is because when load is disconnected Ia is zero hence there are no
voltage drops and no armature flux to cause armature reaction. This change in the terminal
voltage is significant in defining the voltage regulation.
The voltage regulation of an alternator is defined as the change in its terminal
voltage when full load is removed, keeping field excitation and speed constant, divided by the
rated terminal voltage.
So if, Vph = Rated thermal voltage
Eph = No load induced e.m.f.
Then voltage regulation is defined as,
% Reg =

The value of the regulation not only depends on the load current but also on the power factor
of the load. For lagging and unity p.f. conditions there is always drop in the terminal voltage
hence regulation values are always positive. While for leading capacitive load conditions , the
terminal voltage increases as load current Increases. Hence regulation is negative in such cases.
The relationship between load current and the terminal voltage is called load characteristics for
various load power factor conditions are shown in the fig. 38.
3) A 3 phase, 6 pole, star connected alternator has 48 slots and 12 conductors per slot on
the armature. If the rotor at 1200RPM and the flux per pole is 0.3 Wb, calculate the e.m.f.
induced in the armature. The coils are full pitched and the winding factor is 0.95.
sol. : P = 6, slots = 48, conductors/ slots = 12, = 0.3 wb

Ns = Ns = 1200 rpm
f=
for full pitched winding, Kc = 1, Kd = 0.95
Total conductors = slots × conductors/slot = 48×12 = 576
Zph =
Tph =
Eph = 4.44 Kc Kd f Tph
Eph = 4.44×1×0.95×60×0.3×96
= 75.9 × 96
Eph = 7288.70 volts
Eline = 3 Eph = 3×7288.70

Eline = 12.624 Kv

MODULE – 5
5a. Single Phase Transformers:
TRANSFORMER is a static device which transfer electric energy from one electric circuit to
another at any desired voltage without any change in frequency.
PRINCIPLE:- A transformer works on the principle of mutual induction. “Whenever a change

in current takes place in a coil there will be an induced emf in the other coil wound over the same
magnetic core”. This is the principle of mutual induction by which the two coils are said to be
coupled with each other.
V1
Load
Fig.1
The fig1 shows the general arrangement of a transformer. C is the iron core made of laminated
sheets of about 0.35mm thick insulated from one another by varnish or thin paper. The purpose
of laminating the core is to reduce the power loss due to eddy currents induced by the alternating
magnetic flux. The vertical portions of the core are called limbs and the top and bottom portions
are called the yokes. Coils P and S are wound on the limbs. Coil P is connected to the supply and
therefore called as the primary, coil S is connected to the load and is called as the secondary.
An alternating voltage applied to P drives an alternating current though P and this current
produces an alternating flux in the iron core, the mean path of the flux is represented by the
dotted line D. This flux links with the coil S and thereby induces an emf in S.
TYPES AND CONSTRUCTION OF TRANSFORMERS
There are two basic circuits in a transformer

1) Magnetic circuit
2) Electric circuit
The core forms the magnetic circuit and the electric circuit consists of two windings primary and
secondary and is made of pure copper. There are two types of single phase transformers.
a) CORE TYPE
b) SHELL TYPE
Figs (a) and (b) shows the details of the elevation and plan of a core type transformer. The limbs
are wound with half the L.V. and half the H.V. windings with proper insulation between them.
The whole assembly taken inside a steel tank filled with oil for the purpose of insulation and
cooling.
CORE TYPE TRANSFORMER.
In the core type the core is surrounded by the coils but in the shell type the core is on the either
side of the coils. There are three limbs and the central limb is of large cross section than that of
outer limbs, and both the LV and HV windings are wound on the central limb and the outer limb
is only for providing the return path for the flux.
The windings are of concentric type (i.e. LV on which the HV windings) or Sandwich type.
The core is made of very thin laminations of high grade silicon steel material to reduce the eddy
current loss and Hysteresis losses in the core.

2222222222222222222222222222222222
1- Insulation between L V
winding
and the core and the core.
2- L V winding.
3- Insulation between L V
and H V winding winding.
4- End insulation between the coils and
the yoke.
5- H V winding.
6- Limbs.
` 7- Yoke.
FIG. (b)

SHELL TYPE TRANSFORMER.
1 – Outer limbs, 4 – L V winding
2 – Central limb, 5 – Insulation between L V and H V windings.
3 – Insulation between L V and Core. 6 – H V winding. 7 – End insulation
In the shell type transformers the core is of different type having three limbs with the central
limb of larger cross section compared to the two outer limbs and carries both the L V and H V
windings wound over each other with proper insulation between them. The entire assembly is
immersed in a steel tank filled with oil for the cooling purpose.

EMF EQUATION:
Principle: - Whenever a coil is subjected to alternating flux, there will be an induced emf in it
Nd
and is called the statically induced emf e
dt
Let N1, N2 be the no. of turns of the primary and secondary windings, E1, E2 the induced emf in
the primary and secondary coils. be the flux which is sinusoidal f be the frequency in Hz
Figure showing the sinusoidally varying flux of peak value Фm .
Whenever a coil of N no- of tunes are linked by a time varying flux , the average emf induced
in this coil is
Nd
e
dt
As the flux is sinusoidal the change in flux from + m to - m is d = 2 m, and this change
takes place in a duration dt = T/2 seconds.
The average induced emf in these N number of turns is
Eavg = N.d /dt = N.2 m/ (T/2) = 4 mN/T = 4f mN volts (as f =1/T)
We know that the Form factor of a pure sine wave F.F. = Erms/Eavg = 1.11

Therefore, Erms = 1.11 Eavg.
= (1.11) (4f m N) = 4.44 f mN volts.
In the primary coil, N = N1 , E1 = 4.44f m N1 volts
In the secondary coil, N = N2 , E2 = 4.44f m N2 volts
TRANSFORMATION RATIO:
It is defined as the ratio of the secondary induced emf to the primary induced emf.
Therefore, E1 / E2 = N1 / N2 = K
For an ideal (loss free) transformer, the input power is equal to the output power.
Therefore E1I1 = E2I2, from which, E2/E1 = I1/I2
Also the induced emf per turn is same for both the primary and secondary turns.
If the value of the transformation ratio K>1, then it is a step up case.
If the value of the transformation ratio K<1, then it is a step down case.
If the value of the transformation ratio K=1, then it is a one:one transformer.
LOSSES AND EFFICIENCY:
There a two types of power losses occur in a transformer
1) Iron loss
2) Copper loss
1) Iron Loss: This is the power loss that occurs in the iron part. This loss is due to the alternating
frequency of the emf. Iron loss in further classified into two other losses.
a) Eddy current loss b) Hysteresis loss

a) EDDY CURRENT LOSS: This power loss is due to the alternating flux linking the core,
which will induced an emf in the core called the eddy emf, due to which a current called the eddy
current is being circulated in the core. As there is some resistance in the core with this eddy
current circulation converts into heat called the eddy current power loss. Eddy current loss is
proportional to the square of the supply frequency.
b) HYSTERISIS LOSS: This is the loss in the iron core, due to the magnetic reversal of the flux
in the core, which results in the form of heat in the core. This loss is directly proportional to the
supply frequency.
Eddy current loss can be minimized by using the core made of thin sheets of silicon steel
material, and each lamination is coated with varnish insulation to suppress the path of the eddy
currents.
Hysteresis loss can be minimized by using the core material having high permeability.
2) COPPER LOSS: This is the power loss that occurs in the primary and secondary coils when
the transformer is on load. This power is wasted in the form of heat due to the resistance of the
coils. This loss is proportional to the sequence of the load hence it is called the Variable loss
whereas the Iron loss is called as the Constant loss as the supply voltage and frequency are
constants
EFFICENCY: It is the ratio of the out put power to the input power of a transformer
Input = Output + Total losses
= Output + Iron loss + Copper loss
outputpower
outputpower Ironloss copperloss
V2 I 2 cos
V2 I 2 cos Weron Wcopper
Where, V2 is the secondary (out put) voltage, I2 is the secondary (out put) current and cosФ is
the power factor of the load.
The transformers are normally specified with their ratings as KVA,

Therefore, (KVA)(103) cosΦ
Efficiency= ----------------------------------------------
(KVA)(103) cosΦ + Wiron + Wcopper
Since the copper loss varies as the square of the load the efficiency of the transformer at any
desired load x is given by
x. (KVA)(103) cosΦ
Efficiency= -------------------------------------------------
x. (KVA)(103) cosΦ + Wiron + (x)2 Wcopper
Where Wcopper is the copper loss at full load
Wcopper = I2R watts
CONDITION FOR MAXIMUM EFFICIENCY:
In general for the efficiency to be maximum for any device the losses must be minimum.
Between the iron and copper losses the iron loss is the fixed loss and the copper loss is the
variable loss. When these two losses are equal and also minimum the efficiency will be
maximum.
Therefore the condition for maximum efficiency in a transformer is
Iron loss = Copper loss ( whichever is minimum)
VOLTAGE REGULATION:
The voltage regulation of a transformer is defined as the change in the secondary terminal
voltage between no load and full load at a specified power factor expressed as a percentage of
the full load terminal voltage.

(Percentage (No load secondary voltage)-(Full load secondary voltage)
Voltage = ---------------------------------------------------------------------------x 100
Regulation) (Full load secondary voltage)
Voltage regulation is a measure of the change in the terminal voltage of a transformer between
No load and Full load. A good transformer has least value of the regulation of the order of ±5%
1. A 600 KVA transformer has an efficiency of 92% at full load, uni8ty p.f. and at half load,
0.9 p.f. determine its efficiency of 75% of full load and 0.9 p.f.
Sol. : S = 600 KVA, % = 92% on full load and half load both
On full load, % =
0.92 =
…………
(1)
On half load, and
0.92 =
………….. (2)
Subtracting (2) from (1),

= 28695.64
= 38260.86 watts
and Pi = 13913.04 watts
Now n = 0.75 i.e., 75% of full load and cos 2 = 0.9
(Pcu) new = n2 (Pcu) F.L. = (0.75)2 × .
% =
= 91.95%
Transformer has 80 turns on the secondary.
Calculate:
i) The rated primary and secondary currents
ii) The number of primary turns
iii) The maximum value of flux
iv) Voltage induced per turn.
Sol: KVA rating = 250
V1 = 11000 volts
V2 = 415 volts
N2 = 80
N1 = = N2 = 80 = 2120

N1 = 2120
KVA =V1I1 = V2I2
I1 = = = 22.72A
I2 = = = 602.40A
Neglecting drops in primary,
V1 = E1 = 11000
E1 = 4.44f m× N1
= m
m = 0.023 Wb = 23 mWb
Voltage induced per turn = = = 5.1886 volts.
3. In a 25 kVA, 2000/200 V Transformer, the iron and copper losses are 350 watts and 400 watts
respectively, calculate the efficiency at U.P.F. at half and 3/4th full load.
Sol.: S = 25 k V A
P i = 350 W, (P cu )FL = 400 W
i) At half load, cos ∅ = 1
= =

% Efficiency =
% Efficiency = 96.525
ii) At th load, cos∅ = 1
% Efficiency =
% Efficiency = 97.02%
4. A 600 KVA transformer has an efficiency of 92% at full load, uni8ty p.f. and at half load, 0.9
p.f. determine its efficiency of 75% of full load and 0.9 p.f.
Sol. : S = 600 KVA, % = 92% on full load and half load both

On full load, % =
0.92 =
…………
(1)
On half load, and
0.92 =
………….. (2)
Subtracting (2) from (1),
= 28695.64
= 38260.86 watts
and Pi = 13913.04 watts
Now n = 0.75 i.e., 75% of full load and cos 2 = 0.9
(Pcu) new = n2 (Pcu) F.L. = (0.75)2 × .
% =
= 91.95%

5b. Three Phase Induction Motors:

INTRODUCTION
The asynchronous motors or the induction motors are most widely used ac motors in industry.
They convert electrical energy in AC form into mechanical energy. They work on the principle
of electromagnetic induction. They are simple and rugged in construction, quite economical
with good operating characteristics and efficiency, requiring minimum maintenance, but have a
low starting torque. They run at practically constant speed from no load to full load condition.
The 3 - phase induction motors are self-starting while the single phase motors are not self-
starting as they produce equal and opposite torques (zero resultant torque) making the rotor
stationary. The speed of the squirrel cage induction motor cannot be varied easily.
CLASSIFICATION -
They are basically classified into two types based on the rotor construction
1. Squirrel cage motor

2. Slip ring motor or phase wound motor
CONSTRUCTION
Three phase induction motor consists of two parts

(1) Stator (2) rotor
1. Stator
It is the stationary part of the motor supporting the entire motor assembly. This outer frame is
made up of a single piece of cast iron in case of small machines. In case of larger machines they
are fabricated in sections of steel and bolted together. The core is made of thin laminations of
silicon steel and flash enameled to reduce eddy current and hysteresis losses. Slots are evenly
spaced on the inner periphery of the laminations. Conductors insulated from each other are
placed in these slots and are connected to form a balanced 3 - phase star or delta connected stator
circuit. Depending on the desired speed the stator winding is wound for the required number of
poles. Greater the speed lesser is the number of poles.
2. Rotor
Squirrel cage rotors are widely used because of their ruggedness. The rotor consists of hollow
laminated core with parallel slots provided on the outer periphery. The rotor conductors are solid
bars of copper, aluminium or their alloys. The bars are inserted from the ends into the semi-
enclosed slots and are brazed to the thick short circuited end rings. This sort of construction
resembles a squirrel cage hence the name “squirrel cage induction motor”. The rotor conductors
being permanently short circuited prevent the addition of any external resistance to the rotor
circuit to improve the inherent low starting torque. The rotor bars are not placed parallel to each
other but are slightly skewed which reduces the magnetic hum and prevents cogging of the rotor
and the stator teeth.

The rotor in case of a phase wound/ slip ring motor has a 3-phase double layer distributed
winding made up of coils, similar to that of an alternator. The rotor winding is usually star
connected and is wound to the number of stator poles. The terminals are brought out and
connected to three slip rings mounted on the rotor shaft with the brushes resting on the slip rings.
The brushes are externally connected to the star connected rheostat in case a higher starting
torque and modification in the speed torque characteristics are required. Under normal running
conditions all the slip rings are automatically short circuited by a metal collar provided on the
shaft and the condition is similar to that of a cage rotor. Provision is made to lift the brushes to
reduce the frictional losses. The slip ring and the enclosures are made of phosphor bronze.
In both the type of motors the shaft and bearings (ball and roller) are designed for trouble free
operation. Fans are provided on the shaft for effective circulation of air. The insulated (mica and
varnish) stator and rotor windings are rigidly braced to withstand the short circuit forces and
heavy centrifugal forces respectively. Care is taken to maintain a uniform air gap between the
stator and the rotor.

Comparison of the squirrel cage and slip ring rotors

The cage rotor has the following advantages:
1. Rugged in construction and economical.

2. Has a slightly higher efficiency and better power factor than slip ring motor.
3. The absence of slip rings and brushes eliminate the risk of sparking which helps in a
totally enclosed fan cooled (TEFC) construction.
The advantages of the slip ring rotor are:
1. The starting torque is much higher and the starting current much lower when compared to
a cage motor with the inclusion of external resistance.
2. The speed can be varied by means of solid state switching
WORKING OF THE INDUCTION MOTOR

a) Production of a rotating magnetic field
Consider a 3- phase induction motor whose stator windings mutually displaced from each other
by 120° are connected in delta and energized by a 3- phase supply.

The currents flowing in each phase will set up a flux in the respective phases as
The corresponding phase fluxes can be represented by the following equations

sin t sin B m sin t 240

R m m
sin t 120 B m sin 240

Y m
Y m sin 120
The resultant flux at any instant is given by the vector sum of the flux in each of the phases.
(i) When 0  , from the flux waveform diagram ,we have
R 0
3
Y km sin( 120 ) m
2
3
B m sin( 240 ) m
2
The resultant flux r is given by,
3
r 2* m cos(30 ) 1..5 m
2
3
B m
2
3
Y m
2

r 1.5 m
(ii) When 60o
3
R m
2
3
Y m
2
B 0
(iii) When 120
3
R m
2
Y 0
3
B m
2

(iv) When 180
R 0;
3
Y m
2
3
B
2
From the above discussion it is very clear that when the stator of a 3-phase induction motor is
energized, a magnetic field of constant magnitude (1.5 φm) rotating at synchronous speed

(Ns) with respect to stator winding is produced.
(b) Rotation of the rotor
Consider a 3- phase stator winding energized from a 3 phase supply. As explained earlier a
rotating magnetic field is produced running at a synchronous speed NS
120 f
NS = ---------
Where f = supply frequency
P = Number of stator poles
ANIMATION INSTRUCTION
Consider a portion of 3- phase induction motor as shown in the above figure which is
representative in nature. The rotating field crosses the air gap and cuts the initially stationary

rotor conductors. Due to the relative speed between the rotating magnetic field and the initially
stationary rotor,(change of flux linking with the conductor) an e.m.f. is induced in the rotor
conductors, in accordance with the Faraday‟s laws of electromagnetic induction. Current flows in
the rotor conductors as the rotor circuit is short circuited. Now the situation is similar to that of a
current carrying conductor placed in a magnetic field. Hence, the rotor conductors experience a
mechanical force which eventually leads to production of torque. This torque tends to move the
rotor in the same direction as that of the rotating magnetic field.
CONCEPT OF SLIP (S)

According to Lenz‟s law, the direction of rotor current will be such that they tend to oppose the
cause producing it. The cause producing the rotor current is the relative speed between the
rotating field and the stationary rotor. Hence, to reduce this relative speed, the rotor starts
running in the same direction as that of stator field and tries to catch it. In practice the rotor can
never reach the speed of the rotating magnetic field produced by the stator. This is because if
rotor speed equals the synchronous speed, then there is no relative speed between the rotating
magnetic field and the rotor. This makes the rotor current zero and hence no torque is produced
and the rotor will tend to remain stationary. In practice, windage and friction losses cause the
rotor to slow down. Hence, the rotor speed (N) is always less than the stator field speed (NS).
Thus the induction motor cannot run with ZERO SLIP. The frequency of the rotor current
fr = sf. The difference between the synchronous speed (NS) of the rotating stator field and the
actual rotor speed (N) is called the slip speed.
Slip speed = NS – N depends upon the load on the motor
NS - N
% Slip (s) = ---------- * 100
NS
Note: In an induction motor the slip value ranges from 2% to 4%
APPLICATIONS OF INDUCTION MOTORS

Squirrel cage induction motor
Squirrel cage induction motors are simple and rugged in construction, are relatively cheap and
require little maintenance. Hence, squirrel cage induction motors are preferred in most of the
industrial applications such as in
i) Lathes
ii) Drilling machines
iii) Agricultural and industrial pumps
iv) Industrial drives.
Slip ring induction motors
Slip ring induction motors when compared to squirrel cage motors have high starting torque,
smooth acceleration under heavy loads, adjustable speed and good running characteristics.
They are used in
i) Lifts
ii) Cranes
iii) Conveyors , etc.,
Necessity of starters for 3 phase induction motor

When a 3- phase motor of higher rating is switched on directly from the mains it draws a starting
current of about 4 -7 times the full load (depending upon on the design) current. This will cause
a drop in the voltage affecting the performance of other loads connected to the mains. Hence
starters are used to limit the initial current drawn by the 3 phase induction motors.
The starting current is limited by applying reduced voltage in case of squirrel cage type induction
motor and by increasing the impedance of the motor circuit in case of slip ring type induction
motor. This can be achieved by the following methods.
1. Star –delta starter
2. Auto transformer starter

3. Soft starter
Star delta starter
The star delta starter is used for squirrel cage induction motor whose stator winding is delta
connected during normal running conditions. The two ends of each phase of the stator winding
are drawn out and connected to the starter terminals as shown in the following figure.
When the switch is closed on the star-start side

(1) The winding is to be shown connected in star

(2) The current I = 1/3 * (I direct switching)
(3) Reduction in voltage by1/ 3
V = V supply*1/ 3
When the switch is closed on to delta –run side
(1) the winding to be shown connected in delta

(2) (2) application of normal voltage V supply (3) normal current I
During staring the starter switch is thrown on to the STAR - START. In this position the stator
winding is connected in star fashion and the voltage per phase is 1/ 3 of the supply voltage.
This will limit the current at starting to 1/3 of the value drawn during direct switching. When the
motor accelerates the starter switch is thrown on to the DELTA - RUN side. In this position the
stator winding gets connected in the fashion and the motor draws the normal rated current.
WORKED EXAMPLES
1. A 12 pole, 3 phase alternator is coupled to an engine running at 500 rpm. It supplies an

Induction Motor which ahs a full load speed of 1440 rpm. Find the percentage slop and the
number of poles of the motor.
Solution: NA = synchronous speed of the alternator
PNA 12 X 500
F =------- = --------------- = 50 Hz (from alternator data)
120 120
When the supply frequency is 50 Hz, the synchronous speed can be 750 rpm, 1500 rpm,
3000rpm etc., since the actual speed is 1440 rpm and the slip is always less than 5% the
synchronous speed of the Induction motor is 1500 rpm.
NS – N 1500 - 1440
s = --------- = ----------------- = 0.04 OR 4%

NS 1500
120f 120 x 50
NS = ------------ = -------------- = 1500
P P
P=4
2. A 6 pole induction motor is supplied by a 10 pole alternator, which is driven at 600 rpm. If
the induction motor is running at 970 rpm, determine its percentage slip.
P NA 10 X 600
From alternator date: f =------- = --------------- = 50 Hz
120 120
Synchronous speed of the induction motor
120 f 120 50
NS 1000rpm
P 6
From I.M. data:
NS N 1000 970
%slip 100 3%
NS 1000

3. A 12 pole, 3 phase alternator is driven by a 440V, 3 phase, 6 pole Induction Motor running at
a slip of 3%. Find frequency of the EMF generated by the alternator
120 f 120 50
For induction motor: N S 1000rpm
P 6
N 1 s NS 1 0.03 1000 970rpm
As the alternator is driven by the Induction motor, the alternator runs at 970 r.p.m.
PN 12 970
For alternator: f 97Hz
120 120
4. A three phase 4 pole, 440 V, 50Hz induction motor runs with a slip of 4%. Find the rotor
speed and frequency of the rotor current.
Solution:
120 f 120 50
NS 1500rpm
P 4
NS N 1500 N
S i.e.0.04 , N 1440rpm
NS 1500
fr sf 0.04 50 2 Hz
5. A 3 phase, 50Hz 6 pole induction motor has a full load percentage slip of 3%.
Find(i) Synchronous speed and (ii) Actual Speed
Solution:

120 f 120 50
NS 1000rpm
P 6
: NS N 100 N
S i.e.0.03 N 970rpm
NS 1000
6. A 3 phase induction motor has 6 poles and runs at 960 RPM on full load. It is supplied from
an alternator having 4 poles and running at 1500 RPM. Calculate the full load slip and the
frequency of the rotor currents of the induction motor.
Solution:
PN 4 1500
f 50Hz ( from alternator data)
120 120
forInduction motor
120 f 120 50
NS 1000rpm
P 6
N S N 1000 960
S 0.04 or 4%
NS 1000
fr sf 0.04 50 2 Hz

Basic Electricals Engg. 15ele15 Notes PDF

Uploaded by

Copyright:

Available Formats

Basic Electricals Engg. 15ele15 Notes PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basic Electricals Engg. 15ele15 Notes PDF

Uploaded by

Copyright:

Available Formats

For More Visit @ www.vtupro.

Electromagnetic induction: Definition of Electromagnetic Induction, Faradays Laws, Fleming‟s

2b. Measuring Instruments: Construction and Principle of operation of dynamometer type

Department of EEE, SJBIT Page 1

VTU PRO - A Complete Platform For VTU Students

3a.Single-phase A.C. Circuits : Generation of sinusoidal voltage, frequency of generated

5a. Single Phase Transformers: Necessity of transformer, Principle of operation and

Department of EEE, SJBIT Page 2

VTU PRO - A Complete Platform For VTU Students

1 “Basic Electrical Engineering”, D C Kulshreshtha, TMH, 2009 Edition.

2 “Fundamentals of Electrical Engineering”, Rajendra Prasad, PHI, Second Edition, 2009.

1. "Electrical Technology", E. Hughes International Students 9th Edition, Pearson, 2005.

2. “Basic Electrical Engineering”, Abhijit Chakrabarti, Sudiptanath, Chandan Kumar Chanda,

Department of EEE, SJBIT Page 3

VTU PRO - A Complete Platform For VTU Students

Module-1: 1a) DC Circuits

Module-3 3a) Single-phase A.C. Circuits

Module-4 4 a) Three Phase Circuits

Module-5 5 a) Single Phase Transformers

Department of EEE, SJBIT Page 4

VTU PRO - A Complete Platform For VTU Students

The limitations of the Ohm‟s law are,

Department of EEE, SJBIT Page 5

VTU PRO - A Complete Platform For VTU Students

where: V = voltage in volts (V) or: V = voltage in volts (V)

Department of EEE, SJBIT Page 6

VTU PRO - A Complete Platform For VTU Students

State and explain Kirchhoff’s laws.

Kirchhoff‟s current law:

The law can be stated as,

 The word algebraic means considering the signs of various currents.

whie currents flowing away from a junction point assumed to be negative.

 Applying KCL, at junction 0 = 0

 The law is very helpful in network simplification.

Department of EEE, SJBIT Page 7

VTU PRO - A Complete Platform For VTU Students

Kirchhoff’s voltage law :

closed loop is always zero.”

Around a closed path =0

tracing a closed path.

This law is very useful in loop analysis of the network.

A circuit consists of two parallel resistors having resistance of 20 and 30

respectively connected in series with 15 .If current through 15 resistor is 3 A,

Department of EEE, SJBIT Page 8

VTU PRO - A Complete Platform For VTU Students

Resistors connected in Series

This can be extended for more resistors: R = R1 + R2 + R3 + R4 + ...

Resistors connected in Parallel

Department of EEE, SJBIT Page 9

VTU PRO - A Complete Platform For VTU Students

Department of EEE, SJBIT Page 10

VTU PRO - A Complete Platform For VTU Students

Department of EEE, SJBIT Page 11

VTU PRO - A Complete Platform For VTU Students

Dynamically induced emf

Statically induced e.m.f

There is no physical movement of magnet or conductor; it is the alternating supply which

Such type of an induced e.m.f. is available in transformers.

Department of EEE, SJBIT Page 12