NFS-320 Installation Manual

Fire Alarm Control Panel
NFS-320/E/C
Installation Manual
A
Document 52745
01/12/2007 Rev:
P/N 52745:A ECN 06-166
Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and
smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter-
warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level. Rate-of-rise
notification capability—can provide early warning of a develop- heat detectors may be subject to reduced sensitivity over time.
ing fire. Such a system, however, does not assure protection For this reason, the rate-of-rise feature of each detector
against property damage or loss of life resulting from a fire. should be tested at least once per year by a qualified fire pro-
The Manufacturer recommends that smoke and/or heat detec- tection specialist. Heat detectors are designed to protect
tors be located throughout a protected premise following the property, not life.
recommendations of the current edition of the National Fire IMPORTANT! Smoke detectors must be installed in the
Protection Association Standard 72 (NFPA 72), manufacturer's same room as the control panel and in rooms used by the sys-
recommendations, State and local codes, and the recommen- tem for the connection of alarm transmission wiring, communi-
dations contained in the Guide for Proper Use of System cations, signaling, and/or power. If detectors are not so
Smoke Detectors, which is made available at no charge to all located, a developing fire may damage the alarm system, crip-
installing dealers. A study by the Federal Emergency Man- pling its ability to report a fire.
agement Agency (an agency of the United States government) Audible warning devices such as bells may not alert people
indicated that smoke detectors may not go off in as many as if these devices are located on the other side of closed or
35% of all fires. While fire alarm systems are designed to pro- partly open doors or are located on another floor of a building.
vide early warning against fire, they do not guarantee warning Any warning device may fail to alert people with a disability or
or protection against fire. A fire alarm system may not provide those who have recently consumed drugs, alcohol or medica-
timely or adequate warning, or simply may not function, for a tion. Please note that:
variety of reasons:
• Strobes can, under certain circumstances, cause seizures
Smoke detectors may not sense fire where smoke cannot in people with conditions such as epilepsy.
reach the detectors such as in chimneys, in or behind walls, on
roofs, or on the other side of closed doors. Smoke detectors • Studies have shown that certain people, even when they
also may not sense a fire on another level or floor of a building. hear a fire alarm signal, do not respond or comprehend the
A second-floor detector, for example, may not sense a first- meaning of the signal. It is the property owner's responsi-
floor or basement fire. bility to conduct fire drills and other training exercise to
make people aware of fire alarm signals and instruct them
Particles of combustion or “smoke” from a developing fire on the proper reaction to alarm signals.
may not reach the sensing chambers of smoke detectors
because: • In rare instances, the sounding of a warning device can
cause temporary or permanent hearing loss.
• Barriers such as closed or partially closed doors, walls, or
chimneys may inhibit particle or smoke flow. A fire alarm system will not operate without any electrical
power. If AC power fails, the system will operate from standby
• Smoke particles may become “cold,” stratify, and not reach batteries only for a specified time and only if the batteries have
the ceiling or upper walls where detectors are located. been properly maintained and replaced regularly.
• Smoke particles may be blown away from detectors by air Equipment used in the system may not be technically com-
outlets. patible with the control panel. It is essential to use only equip-
• Smoke particles may be drawn into air returns before ment listed for service with your control panel.
reaching the detector. Telephone lines needed to transmit alarm signals from a
The amount of “smoke” present may be insufficient to alarm premise to a central monitoring station may be out of service
smoke detectors. Smoke detectors are designed to alarm at or temporarily disabled. For added protection against tele-
various levels of smoke density. If such density levels are not phone line failure, backup radio transmission systems are rec-
created by a developing fire at the location of detectors, the ommended.
detectors will not go into alarm. The most common cause of fire alarm malfunction is inade-
Smoke detectors, even when working properly, have sensing quate maintenance. To keep the entire fire alarm system in
limitations. Detectors that have photoelectronic sensing excellent working order, ongoing maintenance is required per
chambers tend to detect smoldering fires better than flaming the manufacturer's recommendations, and UL and NFPA stan-
fires, which have little visible smoke. Detectors that have ion- dards. At a minimum, the requirements of NFPA 72 shall be
izing-type sensing chambers tend to detect fast-flaming fires followed. Environments with large amounts of dust, dirt or
better than smoldering fires. Because fires develop in different high air velocity require more frequent maintenance. A main-
ways and are often unpredictable in their growth, neither type tenance agreement should be arranged through the local man-
of detector is necessarily best and a given type of detector ufacturer's representative. Maintenance should be scheduled
may not provide adequate warning of a fire. monthly or as required by National and/or local fire codes and
Smoke detectors cannot be expected to provide adequate should be performed by authorized professional fire alarm
warning of fires caused by arson, children playing with installers only. Adequate written records of all inspections
matches (especially in bedrooms), smoking in bed, and violent should be kept.
explosions (caused by escaping gas, improper storage of
flammable materials, etc.). Limit-C-9-2005
2 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be Like all solid state electronic devices, this system may
connected to the fire alarm control panel. Disconnect all operate erratically or can be damaged when subjected to light-
sources of power before servicing. Control unit and associ- ning induced transients. Although no system is completely
ated equipment may be damaged by removing and/or insert- immune from lightning transients and interference, proper
ing cards, modules, or interconnecting cables while the unit is grounding will reduce susceptibility. Overhead or outside aerial
energized. Do not attempt to install, service, or operate this wiring is not recommended, due to an increased susceptibility
unit until manuals are read and understood. to nearby lightning strikes. Consult with the Technical Ser-
CAUTION - System Re-acceptance Test after Software vices Department if any problems are anticipated or encoun-
Changes: To ensure proper system operation, this product tered.
must be tested in accordance with NFPA 72 after any pro- Disconnect AC power and batteries prior to removing or
gramming operation or change in site-specific software. Re- inserting circuit boards. Failure to do so can damage circuits.
acceptance testing is required after any change, addition or Remove all electronic assemblies prior to any drilling, filing,
deletion of system components, or after any modification, reaming, or punching of the enclosure. When possible, make
repair or adjustment to system hardware or wiring. All compo- all cable entries from the sides or rear. Before making modifi-
nents, circuits, system operations, or software functions known cations, verify that they will not interfere with battery, trans-
to be affected by a change must be 100% tested. In addition, former, or printed circuit board location.
to ensure that other operations are not inadvertently affected,
at least 10% of initiating devices that are not directly affected Do not tighten screw terminals more than 9 in-lbs. Over-
by the change, up to a maximum of 50 devices, must also be tightening may damage threads, resulting in reduced terminal
tested and proper system operation verified. contact pressure and difficulty with screw terminal removal.
This system meets NFPA requirements for operation at 0-49º This system contains static-sensitive components.
C/32-120º F and at a relative humidity 93% ± 2% RH (non- Always ground yourself with a proper wrist strap before han-
condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful dling any circuits so that static charges are removed from the
life of the system's standby batteries and the electronic com- body. Use static suppressive packaging to protect electronic
ponents may be adversely affected by extreme temperature assemblies removed from the unit.
ranges and humidity. Therefore, it is recommended that this Follow the instructions in the installation, operating, and pro-
system and its peripherals be installed in an environment with gramming manuals. These instructions must be followed to
a normal room temperature of 15-27º C/60-80º F. avoid damage to the control panel and associated equipment.
Verify that wire sizes are adequate for all initiating and indi- FACP operation and reliability depend upon proper installation.
cating device loops. Most devices cannot tolerate more than a Precau-D1-9-2005
10% I.R. drop from the specified device voltage.
FCC Warning
WARNING: This equipment generates, uses, and can Canadian Requirements
radiate radio frequency energy and if not installed and This digital apparatus does not exceed the Class A limits
used in accordance with the instruction manual may for radiation noise emissions from digital apparatus set
cause interference to radio communications. It has been out in the Radio Interference Regulations of the Cana-
tested and found to comply with the limits for class A dian Department of Communications.
computing devices pursuant to Subpart B of Part 15 of
FCC Rules, which is designed to provide reasonable Le present appareil numerique n'emet pas de bruits radi-
protection against such interference when devices are oelectriques depassant les limites applicables aux appa-
operated in a commercial environment. Operation of this reils numeriques de la classe A prescrites dans le
equipment in a residential area is likely to cause interfer- Reglement sur le brouillage radioelectrique edicte par le
ence, in which case the user will be required to correct ministere des Communications du Canada.
the interference at his or her own expense.
Acclimate Plus™, HARSH™, NIS™, Notifier Integrated Systems™, NOTI•FIRE•NET™, and ONYXWorks™ are all trademarks; and FlashScan®, NION®,
NOTIFIER®, ONYX®, UniNet®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc. Echelon® is a registered trademark and
LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint Corporation. Microsoft® and Windows® are
registered trademarks of the Microsoft Corporation. LEXAN® is a registered trademark of GE Plastics, a subsidiary of General Electric Company.
©Monday, January 15, 2007 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 3

Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions
about our online Help or printed manuals, you can email us.
Please include the following information:
• Product name and version number (if applicable)
• Printed manual or online Help
• Topic Title (for online Help)
• Page number (for printed manual)
• Brief description of content you think should be improved or corrected
• Your suggestion for how to correct/improve documentation
Send email messages to:
FireSystems.TechPubs@honeywell.com
Please note this email address is for documentation feedback only. If you have any technical issues, please contact
Technical Services.

Table of Contents
Section 1: About This Manual.................................................................................................. 7
1.1: Standards and Other Documents....................................................................................................................7
1.2: UL 864 Compliance.......................................................................................................................................8
1.2.1: Products Subject to AHJ Approval......................................................................................................8
1.3: Related Documents .......................................................................................................................................8
1.4: Cautions and Warnings ..................................................................................................................................9
1.4.1: Typographic Conventions....................................................................................................................9
Section 2: System Overview .................................................................................................. 10
2.1: System Description ......................................................................................................................................10
2.1.1: Standard Features ..............................................................................................................................10
2.1.2: Options ..............................................................................................................................................11
2.1.3: System Limitations ............................................................................................................................11
2.2: System Components ....................................................................................................................................11
2.2.1: Standard Equipment ..........................................................................................................................11
2.2.2: Control Panel Circuit Board .............................................................................................................11
2.2.3: Main Power Supply KAPS-24/E ......................................................................................................12
2.2.4: Circuit Board Components ................................................................................................................13
2.2.5: System Cabinet ..................................................................................................................................15
2.3: Compatible Equipment ...............................................................................................................................16
Notifier Compatible Equipment ...........................................................................................................16
System Sensor Equipment....................................................................................................................17
Retrofit Equipment: Compatible Notifier Equipment Listed Under Previous Editions of UL 864 .....17
Section 3: Installation............................................................................................................. 18
3.1: Preparing for Installation .............................................................................................................................18
3.1.1: Standards and Codes..........................................................................................................................18
3.2: Installation Checklist ...................................................................................................................................19
3.3: Mounting a Cabinet .....................................................................................................................................20
3.4: Installing Option Boards..............................................................................................................................20
Installing a Transmitter Module TM-4.................................................................................................21
Network Control Module .....................................................................................................................22
3.5: Connecting the Power Cables ......................................................................................................................22
3.5.1: Overview ...........................................................................................................................................22
3.5.2: Connecting the Control Panel to AC Power......................................................................................23
3.5.3: Checking AC Power ..........................................................................................................................23
3.5.4: Installing and Connecting the Batteries ............................................................................................24
3.5.5: External DC Power Output Connections...........................................................................................24
3.6: NAC Connections and Releasing Circuits...................................................................................................25
3.7: Output Relay Connections ...........................................................................................................................26
3.8: Backup-Alarm Switches .............................................................................................................................26
3.9: UL Power-limited Wiring Requirements.....................................................................................................27
3.9.1: Labeling Modules and Circuits..........................................................................................................28
3.10: Installing EIA-485 Devices .......................................................................................................................28
3.11: Installing Remote Printers and/or CRT......................................................................................................28
3.11.1: Custom Cable Fabrication ...............................................................................................................28
3.11.2: Installing and Configuring the PRN Series Printer .........................................................................29
Connecting a Remote PRN Series Printer ............................................................................................29
Setting Printer Options .........................................................................................................................29
3.11.3: Installing and Configuring a CRT-2................................................................................................30
Setting CRT-2 Parameters....................................................................................................................30
3.11.4: Connecting Multiple Printers, CRTs, or CRT/PRN Combination ..................................................31
3.12: Wiring a Signaling Line Circuit (SLC)......................................................................................................32
3.13: Connecting a PC for Off-Line Programming ............................................................................................33

Table of Contents
Section 4: Applications .......................................................................................................... 34

4.1: Overview......................................................................................................................................................34
Municipal Box (Auxiliary) ...................................................................................................................34
4.2: NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) ..................................34
4.3: NFPA 72 Proprietary Fire Alarm Systems...................................................................................................35
4.4: Fire/Security Applications ..........................................................................................................................36
4.4.1: General Operation..............................................................................................................................36
4.4.2: Installing a Security Tamper Switch..................................................................................................37
4.4.3: Receiving Unit ...................................................................................................................................37
4.4.4: Programming .....................................................................................................................................37
4.4.5: Wiring for Proprietary Security Alarm Applications ........................................................................38
4.5: Releasing Applications ................................................................................................................................39
4.5.1: Overview............................................................................................................................................39
4.5.2: Programming .....................................................................................................................................39
4.5.3: Wiring ................................................................................................................................................39
4.5.4: Connecting a Releasing Device to the Control Panel ........................................................................40
4.5.5: Connecting a Releasing Device to the FCM-1 Module.....................................................................42
4.5.6: Connecting an NBG-12LRA Agent Release-Abort Station ..............................................................43
Section 5: Testing the System .............................................................................................. 44
5.1: Acceptance Test ...........................................................................................................................................44
5.2: Periodic Testing and Service........................................................................................................................44
5.3: Operational Checks ......................................................................................................................................44
5.4: Battery Checks and Maintenance.................................................................................................................45
Appendix A: Power Supply Calculations ............................................................................. 46
A.1: Calculating AC Branch Circuit Current......................................................................................................46
AC Branch Circuit Installation .............................................................................................................46
A.2: Calculating the System Current Draws ......................................................................................................46
How to Use the Calculating Tables ......................................................................................................46
A.2.1: Calculating the Maximum Secondary Power Fire Alarm Current Draw..........................................49
A.3: Calculating the Battery Requirements ........................................................................................................50
A.3.1: Calculating the Battery Capacity ......................................................................................................50
A.3.2: Calculating the Battery Size .............................................................................................................51
Appendix B: Electrical Specifications .................................................................................. 52
B.1: Electrical Specifications ..............................................................................................................................52
AC Power .............................................................................................................................................52
Batteries ................................................................................................................................................52
Signaling Line Circuit (SLC) ..............................................................................................................52
Notification Appliance Circuits and Releasing Circuits ......................................................................53
Output Relays (common)......................................................................................................................53
Four-wire Smoke Detector Power ........................................................................................................53
Power Output ........................................................................................................................................53
Operating Power: AC Branch Circuit...................................................................................................53
Operating Power: Secondary Power Source (Batteries).......................................................................54
B.2: Wire Requirements......................................................................................................................................54
Index ........................................................................................................................................ 57

Section 1: About This Manual
1.1 Standards and Other Documents

This Fire Alarm Control Panel complies with the following NFPA standards:
• NFPA 12 CO2 Extinguishing Systems
• NFPA 12A Halon 1301 Extinguishing Systems
• NFPA 13 Sprinkler Systems
• NFPA 15 Water Spray Systems
• NFPA 16 Foam/Water Deluge and Foam/Water Spray Systems
• NFPA 17 Dry Chemical Extinguishing Systems
• NFPA 17A Wet Chemical Extinguishing Systems
• NFPA 72 Central Station Fire Alarm Systems (Automatic, Manual and Waterflow) Protected
Premises Unit (requires Notifier UDACT).
• NFPA 72 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Fire Alarm
Systems.
• NFPA 72 Auxiliary (Automatic, Manual and Waterflow) Fire Alarm Systems (requires TM-4).
• NFPA 72 Remote Station (Automatic, Manual and Waterflow) Fire Alarm Systems
• NFPA 72 Proprietary (Automatic, Manual and Waterflow) Fire Alarm Systems (Protected
Premises Unit).
• NFPA 2001 Clean Agent Fire Extinguishing Systems
The installer should be familiar with the following documents and standards:
• NFPA 72 Initiating Devices for Fire Alarm Systems
• NFPA 72 Inspection, Testing and Maintenance for Fire Alarm Systems
• NFPA 72 Notification Appliances for Fire Alarm Systems
Underwriters Laboratories
• UL 38 Manually Actuated Signaling Boxes
• UL 217 Smoke Detectors, Single and Multiple Station
• UL 228 Door Closers - Holders for Fire Protective Signaling Systems
• UL 268 Smoke Detectors for Fire Protective Signaling Systems
• UL 268A Smoke Detectors for Duct Applications
• UL 346 Waterflow Indicators for Fire Protective Signaling Systems
• UL 464 Audible Signaling Appliances
• UL 521 Heat Detectors for Fire Protective Signaling Systems
• UL 864 Standard for Control Units for Fire Protective Signaling Systems
• UL 1481 Power Supplies for Fire Protective Signaling Systems
• UL 1971 Visual Signaling Appliances
• UL 1076 Proprietary Burglar Alarm Systems
• UL 60950 Safety of Information Technology Equipment
Underwriters Laboratories of Canada (ULC)
• Standard CAN/ULC-S527-M99
• CAN/ULC-S524-M91 Standard for the Installation of Fire Alarm Systems
Other
• EIA-485 and EIA-232 Serial Interface Standards
• NEC Article 300 Wiring Methods
• NEC Article 760 Fire Protective Signaling Systems
• Applicable Local and State Building Codes
• Requirements of the Local Authority Having Jurisdiction
• C22.1-98 The Canadian Electrical Code, Part 1

About This Manual UL 864 Compliance
1.2 UL 864 Compliance

1.2.1 Products Subject to AHJ Approval
This product has been certified to comply with the requirements in the Standard for Control Units
and Accessories for Fire Alarm Systems, UL 864 9th Edition.
The following products have not received UL 864 9th Edition certification and may only be used in
retrofit applications. Operation of the NFS-320/E/C with products not tested for UL 864 9th
Edition has not been evaluated and may not comply with NFPA 72 and/or the latest edition of UL
864. These applications will require the approval of the local Authority Having Jurisdiction (AHJ).
• For a complete list of all peripherals that can be used with this fire alarm control panel (FACP),
and which of those peripherals have not received UL 864, 9th Edition certification and may
only be used in retrofit applications, see Section 2.3, “Compatible Equipment”, on page 16.
1.3 Related Documents

Table 1.1 below provides a list of documents referenced in this manual, as well as documents for
selected other compatible devices. The document series chart (DOC-NOT) provides the current
document revision. A copy of this document is included in every shipment.
Compatible Conventional Devices (Non-addressable) Document Number
Device Compatibility Document 15378
Fire Alarm Control Panel (FACP) and Main Power Supply Installation Document Number
NFS-320/E/C Installation, Operations, and Programming Manuals 52745, 52746, 52747

NFS-320C Canadian Applications Addendum 52745CDN
SLC Wiring Manual 51253
Note: For individual SLC Devices, refer to the SLC Wiring Manual
Off-line Programming Utility Document Number
VeriFire™ Tools CD help file VERIFIRE-TCD
Power Supplies, Auxiliary Power Supplies & Battery Chargers Document Number
ACPS-2406 Installation Manual 51304
APS-6R Instruction Manual 50702
CHG-120 Battery Charger Manual 50641
FCPS-24S6/FCPS-24S8 Field Charger/Power Supply Manual 51977
Networking Document Number
Noti•Fire•Net Manual, Network Version 4.0 & Higher 51584
ONYXWorks™ Workstation Hardware & Software Application: Installation and Operation Manual 52342
ONYXWorks™ NFN Gateway (PC Platform) Installation & Operation Manual 52307
ONYXWorks™ NFN Gateway (Embedded Platform) Installation & Operation Manual 52306
NCM-W/F Installation Document 51533
NCS ONYX® Network Control Station Manual, Network Version 4.0 & Higher 51658
NCA-2 Network Control Annunciator Manual 52482
Table 1.1 Reference Documentation (1 of 2)

Cautions and Warnings About This Manual
NCA Network Control Annunciator Manual 51482
System Components Document Number
Annunciator Control System Manual 15842
Annunciator Fixed Module Manual 15048
AFM-16A Annunciator Fixed Module Manual 15207
ACM-8R Annunciator Control Module Manual 15342
FDU-80 Remote Annunciator Manual 51264
LDM Series Lamp Driver Annunciator Manual 15885
SCS Smoke Control Manual (Smoke and HVAC Control Station) 15712
DPI-232 Direct Panel Interface Manual 51499
TM-4 Installation Document (Reverse Polarity Transmitter) 51490
UDACT Manual (Universal Digital Alarm Communicator/Transmitter) 50050
FireVoice-25/50 & FireVoice-25/50ZS Manual 52290
RA400Z Remote LED Annunciator Installation Document I56-508
Table 1.1 Reference Documentation (2 of 2)
1.4 Cautions and Warnings

This manual contains cautions and warnings to alert the reader as follows:
CAUTION:
! Information about procedures that could cause programming errors, runtime errors, or equipment
damage.
WARNING:
! Indicates information about procedures that could cause irreversible damage to the control panel,
irreversible loss of programming data or personal injury.
1.4.1 Typographic Conventions

NOTE: The term NFS-320 is used in this manual to refer to the NFS-320, the NFS-320E and the
NFS-320C unless otherwise noted.

Section 2: System Overview
2.1 System Description

The NFS-320/E/C control panel is a modular, intelligent fire alarm control panel (FACP) with an
extensive list of powerful features. The control panel uses the KAPS-24/E power supply with
integral battery charger. This is mounted in its cabinet to create a complete fire alarm control
system. The panel supports FlashScan® and CLIP mode; the board provides an integral signalling
line circuit (SLC) that can support up to 318 addressable points (159 detectors and 159
monitor/control modules). The panel is networkable, and can be monitored across a network by
other networked panels.
Modular devices mount in the cabinet or in auxiliary backboxes to provide additional circuits. A
240-volt Export version is available. Cabinetry can be ordered in black or in red. The
NFS-320/E/C chassis is removable, allowing work to be done outside the cabinet.
2.1.1 Standard Features

• Uses Notifier’s VIEW® early warning fire detection and the FlashScan® or Classic Loop
Interface Protocol (CLIP) families of detectors and modules
• Four standard Notification Appliance Circuits (NAC), Class A or B
• Alarm, Trouble, Supervisory and Security relays
• Support for 32 annunciator addresses, with 10 special annunciator groups
• Supports Style 4, Style 6, Style 7 SLC loops
• Releasing service using on-board NACs or FCM-1 modules
• Logic Equations
• Display scroll selection
• Alarm verification supervisory indication (NYC)
• Supervisory duct detectors
• Supports ONYX® Intelligent Sensing algorithms
• Network operation
• Battery charger supports 18 to 200 amp hour sealed lead-acid batteries
• EIA-485 connections for wiring ACS annunciators (including LDM custom graphic
annunciators), TM-4 transmitter
• EIA-232 connections for printer, CRT, printer/CRT, or network operation
• Veri·Fire Tools® off-line programming utility
• Autoprogram feature for faster device programming
• The control panel provides 6 amps of usable output power in an alarm condition; it provides
3 amps of usable output power in normal or continuous operating conditions
• Diagnostic LEDs and switches
• Ground fault detection (0 ohm impedance)
• Battery and battery-charger supervision, voltage-monitoring, and current-monitoring
• Programmable for strobe synchronization
• QWERTY silicone-rubber keypad with a 2x40 LCD display and eight indicator LEDs

System Components System Overview
2.1.2 Options
Refer to Section 2.2 “System Components” for descriptions of the various optional modules.
• Optional devices include: NCM-W/F connection to NotiFireNet, UDACT Universal Digital
Alarm Communicator/Transmitter, and ACM-8R remote relay module to increase point
capacity.
• Optional annunciators connected through the EIA-485 interface allow remote system
monitoring.
2.1.3 System Limitations

System expansion must take into consideration the following:
1. The physical limitations of the cabinet configuration.
2. The electrical limitations of the system power supply.
3. The capacity of the secondary power source (standby batteries). (Note that batteries larger
than 26 AH will require a separate battery backbox.)
2.2 System Components

2.2.1 Standard Equipment
The standard, factory-assembled NFS-320/E/C system includes the following components:
• The control panel, power supply, and cabinet. CPU-320 (120V operation) or CPU-320E
(240V operation), and KAPS-24/E. CPU-320/E is the “control panel” itself and the heart of
the system; it ships with a grounding cable, battery interconnect cables, and document kit.
KAPS-24/E mounts directly on the control panel. The system ships pre-installed in its cabinet.
• A primary display KDM-R2 keypad/display.
Batteries are ordered separately; refer to Appendix A.3 “Calculating the Battery Requirements” for
system current-draw calculations.
Up to two option boards can be installed within the FACP’s cabinet; additional optional peripherals
can be mounted in auxiliary backboxes. Refer to Section 2.3, “Compatible Equipment” for
equipment listed for use with this FACP.
2.2.2 Control Panel Circuit Board

The control panel electronics are contained in CPU-320/E and its built-in power supply. The
printed circuit board incorporates a signaling line circuit (SLC) and the central processing unit; the
power supply has an integral battery charger. A keypad/display unit is installed over the power
supply as shown Figure 2.1. Wiring is shown in Figure 2.2, “CPU-320 and Power-Supply: Wiring
Connections” and Figure 2.3, “CPU-320 and Power-Supply: Jumpers, LEDs and Switches”.

System Overview System Components
320door_open.wmf
Figure 2.1 NFS-320/E/C System, Shown with Door Open
2.2.3 Main Power Supply KAPS-24/E

The main power supply mounts directly over the control panel’s circuit board. It provides a total of
3.9 A (7.4 A in alarm) and contains an integral battery charger. This can be used for many
functions including:
• Powering the NFS-320/E/C
• Powering a variety of UL-listed 24 VDC notification appliances from four built-in NAC
outputs
• Providing up to 1.25 A of resettable power for four-wire smoke detectors
• Providing up to 1.25 A of non-resettable power for external devices such as the TM-4
Transmitter Module.
See Figure 2.2, “CPU-320 and Power-Supply: Wiring Connections” and Figure 2.3, “CPU-320 and
Power-Supply: Jumpers, LEDs and Switches” for details.

TB10 - DC Power TB11 - EIA-485 Terminal Mode Connection (supervised)
(24 VDC power-limited) (Figure 3.12 on page 28)
Non-resettable TB11 - EIA-485 ACS Mode Connection (supervised)
Resettable
(See Figure 3.6 on page 24) TB12 - EIA-232 Printer Connection (Figure 3.13 on page 29)
TB12 - EIA-232 PC/Terminal Connection (CRT)
(Figure 3.14 on page 30)
J1 - Network/Service Connection (NUP)
System Components
(power-limited, supervised)
J2 - USB A VeriFire Tools Connection

J3 - USB B VeriFire Tools Connection
TB13 - SLC Loop #1
All NAC Circuits: (supervised,
power-limited, supervised power-limited)
(Figure 3.8 on page 25) (Figure 3.16)
TB9 - NAC#1
TB3 - Battery Connection

TB8 - NAC#2
(over-current protected, non-power-limited)
(+) (-)
NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

F2 - 15 Amp
Slo-Blow Fuse P/N
2.2.4 Circuit Board Components
TB7 - NAC#3 12057
TB6 - NAC#4
details. (Larger images are referenced on these drawings.)
TB1 - AC Power Connection

(non-power-limited)
Hot
TB5 - Neutral
Figure 2.2 CPU-320 and Power-Supply: Wiring Connections

Supervisory Relay Earth
Security Relay Ground
TB4 -
CPU320-KAPS.wmf
Alarm Relay
Trouble Relay
shows jumpers, LEDs and switches. See Section 3 “Installation” for larger images and more
Output Relays - power-limited only if connected to a power-limited

LEDs on the CPU-320 and its power supply. Figure 2.2 shows wiring connections; Figure 2.3
source. (See Figure 3.9 on page 26 for details.) J7 - KDM-R2

Connection J5 - Security Tamper Switch
The following three figures illustrate the location of the various connections, switches, jumpers and
13
System Overview
J6 - Auxiliary Trouble Input

JP1 - SLC Ground
14
JP2 - Cut for 200MA Operation Fault Jumper
NAC
LEDs
System Overview
F2 - 15 Amp Slo-Blow Fuse P/N 12057

SW1 - Ground Fault Detection Enable/Disable
LED3 - Earth Fault LED (general board ground fault)
LED10 – SLC Loop

Ground Fault LED
CPU320-KAPS.wmf, CPU2-640-LEDs.wmf
Disable - Enable Switches System Switches - ‘No

for Backup Alarm Keyboard Operation’
(Figure 3.10 on page 26) SW5 - Acknowledge
SW6 - Silence
SW7 - Reset
LED1 - Power-on LED (AC or battery)
Figure 2.3 CPU-320 and Power-Supply: Jumpers, LEDs and Switches

LED2 - Signals Silenced LED
LED3 - Point Disabled LED
LED4 - System Trouble LED
LED5 - Supervisory LED
LED6 - Security LED
LED7 - Pre-Alarm LED
System Components
NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

LED8 - Fire Alarm LED
System Components System Overview
2.2.5 System Cabinet

The control panel is factory installed in its backbox. The lockable door is hinged on the left and
opens a full 180 degrees. Mounting methods include surface-mounting or semi-flush mounting on
a wall between 16 inch (40.64 cm) on-center studs. A trim ring option is available for semi-flush
mounting.
External measurements:
• Backbox: 18.12 in. (46.025 cm) width;
18.12 in. (46.025 cm) height;
5.81 in. (14.76 cm) depth.
• Door: 18.187 in. (46.195 cm) width;
18.40 in. (46.736 cm) height;
0.75 in. (1.905 cm) depth.
When using trim ring TR-320, mount mount backbox with at least 1 inch (2.54 cm) between wall
surface and front of backbox, to allow door to open fully past the trim ring. The TR-320 molding
width is 0.905 in. (2.299 cm).
Additional Options
The NFS-320/E/C control panel provides space for one or two additional option boards to be
installed, as shown in Figure 3.3 on page 21. The NFS-320C fulfills ULC annunciation
requirements; see NFS-320C Canadian Applications Addendum for details. NFS-320/E/C A
variety of compatible annunciators are available with their own backboxes; see Section 2.3,
“Compatible Equipment”.

System Overview Compatible Equipment
2.3 Compatible Equipment

These are the most common devices at time of publishing; the most complete list of compatible
intelligent SLC loop devices is provided in the SLC Wiring Manual; for conventional
non-addressable equipment see the Device Compatibility Document. These devices are UL and
ULC listed unless marked otherwise (in parentheses next to the product). Other control panels and
their equipment can also be connected in a network, via Noti•Fire•Net version 5.0; refer to the
Noti•Fire•Net Version 4.0 & Higher Installation Manual for details. For products documented
separately, see Section 1.3 “Related Documents”.
WARNING: UL 9th Edition Compliance

! This product has been certified to comply with the requirements in the Standard for Control Units and
Accessories for Fire Alarm Systems, UL 864 9th Edition. Operation of the NFS-320/E/C with
products not tested for UL 864 9th Edition has not been evaluated and may not comply with NFPA 72
and/or the latest edition of UL 864. These applications will require the approval of the local Authority
Having Jurisdiction (AHJ).
Peripheral devices in the second list were listed under UL 8th Edition and may only be used in retrofit
applications (see Section 1.2, “UL 864 Compliance”, on page 8).
Notifier Compatible Equipment

NOTE: Products marked with a checkmark “✔” have not received UL 864 9th Edition certification
and may only be used in retrofit applications (see Section 1.2, “UL 864 Compliance”, on page 8).
ABF-1B Annunciator Flush Box FDX-551 Intelligent Thermal Sensor

ABF-1DB Annunciator Flush Box with Door FDU-80, FDU-80G Remote Fire Annunciator
ABF-2B Annunciator Flush Box FMM-1 Monitor Module
ABF-2DB Annunciator Flush Box with Door FMM-101 Mini Monitor Module
ABF-4B Annunciator Flush Box FSB-200S Single-ended beam smoke detector with
ABF-4DB Annunciator Flush Box with Door sensitivity testing
ABM-16AT Annunciator Blank Module FSB-200 Single-ended beam smoke detector.
ABM-32A Annunciator Module Blank FSD-751P Photoelectric Duct Detector
ABS-1TB Annunciator Surface Box FSD-751RP Photoelectric Duct Detector with alarm
ABS-1B Annunciator Surface Box relay
ABS-2B Annunciator Surface Box FSD-751PL Low-flow Duct Detector
ABS-4B Annunciator Surface Box FSD-751RPL Low-flow Duct Detector with alarm
ABS-8RB Annunciator Backbox for ACM-8R relay
ACM-24AT Annunciator Control Module DHX-501, DHX-502 Duct Detectors
ACM-48A Annunciator Control Module FSI-751, FSI-851 Ion Detector
ACM-8R Annunciator Control Module FAPT-751, FAPT-851 Acclimate Plus™
AEM-24AT Annunciator Expander Module Combination Photoelectric/Heat Detector
AEM-48A Annunciator Expander Module FSH-751 HARSH™ Smoke Detector
AFM-16A Annunciator Fixed Module HPX-751Intelligent HARSH™ Detector(CLIP)
AFM-16AT Annunciator Fixed Module FSL-751 VIEW® Low Profile Laser Detector
AFM-32A Annunciator Fixed Module FSM-101 Pull Station Monitor Module
AKS-1B Annunciator Key Switch FPJ Firefighter’s Phone Jack
BAT-12180 Battery 12-volt, 18 amp-hour FRM-1 Relay Module
BAT-12250 Battery 12-volt, 25 amp-hour FSP-751, FSP-851 Photo Detector
BAT-12260 Battery 12-volt, 26 amp-hour FSP-751T, FSP-851T Photo/Thermal Detector
BAT-12550 Battery 12-volt, 55 amp-hour FST-751, FST-851 Thermal Detector
BAT-12600 Battery 12-volt, 60 amp-hour FST-751R, FST-851R Thermal Detector (rate of rise)
BAT-121000 Battery 12-volt, 100 amp-hour FST-851H High Temperature Detector
BX-501 Intelligent Detectors/Sensors Base FTM-1 Telephone Module
B501 Intelligent base FZM-1 Monitor and Zone Interface Module
B501BH Sounder base FDM-1 Dual Monitor Module
B710LP Intelligent detector base ISO-X Loop Fault Isolator Module
CCM-1 Communication Converter Module KDM-R2 Keypad/Display Unit
CMX-1 Addressable Control Module LDM-32 Lamp Driver Module
CMX-2 Addressable Control Module LDM-E32 Lamp Driver Module
CPU-320/E/C control panel circuit board LDM-R32 Lamp Driver Module
CPX-551 Ionization Smoke Detector LPX-751 VIEW® Low Profile Laser Detector (CLIP
CPX-751 Intelligent Ionization Smoke Detector mode)
CRT-2 Video Display Monitor with Keyboard MMX-1 Addressable Monitor Module
DPI-232 Direct Panel Interface MMX-2 Addressable Monitor Module
FCM-1 NAC Module MMX-101 Addressable Mini Monitor Module
FCPS-24S6/S8 Field Charger Power Supply NBG-12LRA Agent Release-Abort Station
Continued on next page...
Compatible Equipment System Overview
NBG-12 Series Manual Pull Station A77-716B End-of-Line Resistor Assembly

NBG-12LX Addressable Manual Pull Station RPT-485F EIA-485 Repeater (Fiber)
NCA-2 Network Control Annunciator RPT-485W EIA-485 Repeater (Wire)
NCM-F Network Control Module (Fiber) RPT-485WF EIA-485 Repeater (Wire/Fiber)
NCM-W Network Control Module (Wire) SCS-8, SCE-8 Smoke Control Station
NCS Network Control Station SCS-8L, SCE-8L Smoke Control Lamp Driver
N-ELR Assortment ELR Pack with Mounting Plate SDX-551 Intelligent Photoelectric Detector
NFS-LBB Battery Box SDX-751 Intelligent Photoelectric Detector
NFS-LBBR Red Battery Box STS-1 Security Tamper Switch
ONYXWorks Graphical Workstation TM-4 Transmitter Module
PRN-6 80-Column Printer UDACT Universal Digital Alarm Communicator
R-120 120 Ohm End-of-Line Resistor Transmitter
R-2.2K 2.2K End-of-Line Resistor XP6-C Supervised Control Module
R-27K 27K End-of-Line Resistor XP6-R Six Relay Control Module
R-470 470 End-of-Line Resistor XP6-MA Six Zone Interface Module
R-47K 47K End-of-Line Resistor XP10-M Ten Input Monitor Module
System Sensor Equipment

A2143-00 End of Line Resistor Assembly FSB-200, FSB-200S Beam Detectors
EOLR-1 End-of-Line Resistor Assembly
Retrofit Equipment: Compatible Notifier Equipment Listed Under Previous

Editions of UL 864
NOTE: The products in this list have not received UL 864 9th Edition certification and may only be
used in retrofit applications (see Section 1.2, “UL 864 Compliance”, on page 8).
✔ACM-16AT Annunciator Control Module ✔PRN-4, PRN-5 80-Column Printer
✔ACM-32A Annunciator Control Module ✔RA400 Remote Annunciator
✔ACPS-2406 Auxiliary Charger/Power Supply ✔RA400Z Remote Annunciator with diode
✔AEM-16AT Annunciator Expander Module ✔XP5-C Transponder Control Module
✔AEM-32A Annunciator Expander Module ✔XP5-M Transponder Monitor Module
✔APS-6R Auxiliary Power Supply ✔XPC-8 Transponder Control Module
✔BGX-101L Addressable Manual Pull Station ✔XPDP Transponder Dress Panel
✔CHG-120 Battery Charger ✔XPM-8 Transponder Monitor Module
✔FCPS-24 Field Charger Power Supply ✔XPM-8L Transponder Monitor Module
✔IPX-751 Advanced Multi-Sensor Intelligent ✔XPP-1 Transponder Processor
Detector (Discontinued) ✔XPR-8 Transponder Relay Module
✔NCA Network Control Annunciator

Section 3: Installation
3.1 Preparing for Installation

Choose a location for the fire alarm system that is clean, dry, and vibration-free with moderate
temperature. The area should be readily accessible with sufficient room to easily install and
maintain it. There should be sufficient space for cabinet door(s) to open completely.
Carefully unpack the system and inspect for shipping damage. Count the number of conductors
needed for all devices and find the appropriate knockouts. (Refer to Section 3.9 “UL
Power-limited Wiring Requirements” for selection guidelines.)
Before installing the fire alarm system, read the following:
• Review the installation precautions at the front of this manual, including temperature and
humidity limits for the system (Page 3).
• All wiring must comply with the National and Local codes for fire alarm systems.
• Do not draw wiring into the bottom 9 inches (22.86 cm) of the cabinet except when using a
separate battery cabinet; this space is for internal battery installation.
• Review installation instructions in Section 3.2 “Installation Checklist”.
CAUTION:
! Make sure to install system components in the sequence listed below. Failure to do so can damage
the control panel and other system components.
WARNING:
! This system contains static-sensitive components. Always ground yourself with a proper wrist strap
before handling any circuits. Use static-suppressive packaging to protect electronic assemblies
removed from the unit.
3.1.1 Standards and Codes

In addition, installers should be familiar with the following standards and codes:
• NEC Article 300 Wiring Methods.
• NEC Article 760 Fire Protective Signaling Systems.
• Applicable Local and State Building Codes.
• Requirements of the Local Authority Having Jurisdiction.
• C22.1-98 The Canadian Electrical Code, Part 1.
• CAN/ULC-S5524-01 Standard for the Installation of Fire Alarm Systems.

Installation Checklist Installation
3.2 Installation Checklist

Table 3.1 provides an installation checklist for installing, wiring, and testing the NFS-320/E/C
system. It has references to installation information included in manuals listed in Section 1.3
“Related Documents”.
Seq Task Refer to
1. Mount the cabinet backbox to the wall. Section 3.3 “Mounting a Cabinet”
2. If adding option boards such as such as NCM-W/F or TM-4: Section 3.4 “Installing Option Boards”,
• Remove keypad. Section 1. “Remove and re-install KDM-R2 as shown in
• Install option boards Figure 3.2. It may be convenient to do some basic
• Replace keypad field-wiring before reinstalling KDM-R2.”, and Section 3.4
“Installing Option Boards”
Also see option board documentation for board-specific
details.
3. Optional: Install auxiliary power supply and/or external Auxiliary power manuals, Section 3.8 “Backup-Alarm
battery charger; set backup-alarm switches. Switches”
4. Connect AC wiring, place batteries into backbox without Section 3.5 “Connecting the Power Cables”
connecting them, and run cable to optional power supplies,
DC power outputs, NACs, and relays.
CAUTION: Do not apply AC or DC power at this time.
5. Optional: Install output devices such as a printer, or CRT Section 3.11 “Installing Remote Printers and/or CRT”
terminal.
6. Wire annunciators and network connections. Relevant product manuals
7. Wire the Signaling Line Circuits. Section 3.12 “Wiring a Signaling Line Circuit (SLC)”
8. Terminate wire shielding as instructed. SLC Wiring Manual
9. Apply AC power to the control panel by placing the external circuit breaker to the ON position.
Do NOT connect batteries.
10. Check AC power. Table 3.2 in Section 3.5 “Connecting the Power Cables”
11. Connect the batteries using interconnect cable, P/N 75560 and 75561.
12. Program the control panel. NFS-320/E/C Programming Manual and VeriFire Tools
Online Help.
13. Field test the system. Section 5 “Testing the System”
Table 3.1 Installation Checklist
Top two
mounting holes
Location for 1 or 2
option boards
Two lower
mounting holes
are behind
batteries.
Figure 3.1 NFS-320/E/C in Cabinet

Installation Mounting a Cabinet
3.3 Mounting a Cabinet

This section provides instructions for mounting the NFS-320/E/C backbox to a wall. The
NFS-320/E/C is assembled with a removable chassis that can be removed to provide easier access
to the backbox’s mounting holes, or to allow the electronics to be worked on outside the cabinet.
Follow these guidelines when mounting the backbox:
• Locate the backbox so that the top edge is 66 inches (1.6764 m) above the surface of the
finished floor.
• Access to the cabinet shall be provided in accordance with NFPA 90, article 110.33.
• Allow sufficient clearance around cabinet for door to swing freely. (See Section 2.2.5 “System
Cabinet”.)
• Use the four holes in the back surface of the backbox to provide secure mounting. (See
Figure 3.1.)
• Mount the backbox on a surface that is in a clean, dry, vibration-free area.
CAUTION:
! Unless you are familiar with the placement of components within this backbox, only use the knockout
locations provided for conduit entry.
Follow the instructions below.

1. Mark and pre-drill holes for the top two keyhole mounting bolts (0.25 inch, 0.635 cm). Use
mounting hardware appropriate for the mounting surfaces; see UL 2017 Pull-Test
Requirements.
2. Select and punch open the appropriate knock-outs. (For selection guidelines, see Section 3.9
“UL Power-limited Wiring Requirements”.)
3. Using the keyholes, mount the backbox over the two screws.
4. Mark the location for the two lower holes, remove the backbox and drill the mounting holes.
5. Mount the backbox over the top two screws, then install the remaining fasteners. Tighten all
fasteners securely.
6. Feed wires through appropriate knockouts.
3.4 Installing Option Boards

The NFS-320/E/C ships fully assembled with in its cabinet. One or two option boards can be
mounted inside the NFS-320 cabinet, under the keypad, as shown in Figure 3.3. Option boards that
can be installed internally include NCM-W, NCM-F, TM-4, and UDACT. See Section 2.3,
“Compatible Equipment” for a complete list. When installing option boards, temporarily remove
the KDM-R2 keypad/display unit to provide full access to hardware connections. It may be
convenient to do some basic field-wiring before reinstalling KDM-R2.
NOTE: UDACT only:

If using UDACT inside the cabinet, do not install a second option board.
See the UDACT Manual for instructions on using the mounting bracket.

Installing Option Boards Installation
1. Remove and re-install

KDM-R2 as shown in
Figure 3.2. It may be
convenient to do some
basic field-wiring before
320_assembly_tech_pubs_5.wmf
reinstalling KDM-R2.
2. Lay the first option board
over the four stand-offs
already installed on the
CPU, so that the holes and
stand-offs align.
Figure 3.2 Removing and Reinstalling KDM-R2
3. If attaching a second
option board, use its standoffs to
secure the first option board, then lay
the second option board over the
standoffs. Two sizes of standoffs are
shipped with the option boards; select
standoffs that allow sufficient
320_assembly_tech_pubs_3.wmf
clearance for electronics on the lower
option board.
4. Secure the top option board with four
#4-40 screws (supplied).
5. Re-attach KDM-R2.
Figure 3.3 Installing Option Boards
CAUTION:
! It is critical that all mounting holes of the NFS-320/E/C are secured with a screw or standoff to insure
continuity of Earth Ground.
NOTE: It may be convenient to field-wire the SLC loop before installing any option boards, and
to make wiring connections on the first option board before installing a second option board in
front of it.
Installing a Transmitter Module TM-4

TM-4 is power-limited. Connections are on TB10 nonresettable output and TB11 EIA-485 ACS
Mode. Refer to the Transmitter Module TM-4 installation document for installation details.

Installation Connecting the Power Cables
Network Control Module

If networking two or more control panels or network control annunciators, each unit requires a
Network Control Module (NCM); wire and fiber versions are available. The NCM-W/F takes one
of the NFS-320/E/C’s option-board slots, mounted in front of the control panel on the right.
1. Mount the NCM in the selected position (see Section 3.4, “Installing Option Boards”).
2. Connect J1 on the control panel to J3 on the NCM using the network cable provided
(P/N 75556) as described in the NCM Installation Document. Do not connect two NCMs via
NUP ports (“NUP to NUP”).
3. Connect Channel A and/or Channel B as described in the NCM Installation Document.
NOTE: See the Noti•Fire•Net Manual and NCM Installation Document for wiring diagrams and
system configuration information. See the BMP-1 Product Installation Drawing if considering
mounting the module behind blank module plate in a dress plate or annunciator backbox.
NOTE: Over-bending fiber-optic cable can damage it. Do not exceed a 3 inch (7.62 cm)
minimum bend radius.
3.5 Connecting the Power Cables

WARNING:
! Remove all power sources to equipment while connecting electrical components. Leave the
external, main power breaker OFF until installation of the entire system is complete.
WARNING:
! Several sources of power can be connected to the control panel. Before servicing the control panel,
disconnect all sources of input power including the battery. While energized, the control panel and
associated equipment can be damaged by removing and/or inserting cards, modules, or
interconnecting cables.
3.5.1 Overview
Complete all mounting procedures and check all wiring before applying power. Electrical
connections include the following:
• Primary AC power source – 120 VAC, 50/60 Hz, 5.0 A from line voltage source (with
NFS-320E use 240 VAC, 50/60 Hz, 2.5 A). Overcurrent protection for this circuit must
comply with Article 760 of the National Electrical Code (NEC) and/or local codes. Use 12
AWG (3.31 mm2) wire (maximum) with a 600-volt rating.
• Secondary power source – 24 VDC from batteries, installed in the control panel (or in an
optional battery cabinet). Secondary (battery) power is required to support the system during
loss of primary power.
• External power sources – 24 VDC power for Smoke Detectors (4 wire), NACs, and
Annunciators.
See Appendix B “Electrical Specifications” for details and overall installation guidelines.

Connecting the Power Cables Installation
3.5.2 Connecting the Control Panel to AC Power

Connect primary power as follows (see
TB1 - AC Power Connection
Figure 3.4):
1. Turn off the circuit breaker at the main Hot
power distribution panel. Neutral
KAPS-24-AC.wmf
2. Open the hinged insulating cover on TB1. Ground
(Earth)
3. Connect the service ground to terminal
marked Ground (Earth).
4. Connect the primary neutral line to terminal
marked NEUTRAL and the primary Hot line Figure 3.4 KAPS-24/E:
to terminal marked HOT. AC Power Connections
5. Close the hinged insulating cover over TB1.
3.5.3 Checking AC Power

Table 3.2 contains a checklist for checking the system with AC power applied:
CAUTION:
! While checking AC power, make sure batteries are not connected.
Follow the sequence of steps in Section 3.2 “Installation Checklist”, Table 3.1; this is Step 10.
Component Status
Control panel The green AC Power indicator on; the system Trouble indicator on because batteries are not connected.
circuit board
Each option board In an unconfigured system, the yellow Trouble indicator may come on for approximately 10 seconds after
applying AC power.
Each auxiliary power The yellow Trouble indicator comes on because batteries are not connected.
supply
Table 3.2 AC Power Checklist

Installation Connecting the Power Cables
3.5.4 Installing and Connecting the Batteries

w
WARNING:
! Battery contains sulfuric acid which can cause severe burns to the skin and eyes, and can destroy
fabrics. If contact is made with sulfuric acid, immediately flush skin or eyes with water for 15 minutes
and seek immediate medical attention.
WARNING:
! Do not connect the Battery Interconnect Cables (P/N 75560 and 75561) at this time. Make this
connection AFTER initial system primary powerup. Follow sequence of steps in Section 3.2
“Installation Checklist”, Table 3.1; this is Step 11.
Batteries are installed in the control panel cabinet TB3 - Battery Connection
or in a separate battery cabinet which can be
mounted below the control panel or up to 20 feet Battery (+) Battery (-)
(6.096 m) away from the control panel, in conduit
in the same room.
Connect the battery as follows (see Figure 3.4
above):
1. Install batteries into bottom of cabinet or into
separate battery cabinet.
2. Connect the red cable from TB3(+) on the Figure 3.5 KAPS-24/E:
KAPS-24/E power supply to the positive (+) DC Power Connections
terminal of one battery.
3. Connect the black cable from TB3(–) on the
KAPS-24/E power supply to the negative (–) terminal of the other battery.
4. Connect the remaining cable between the negative (-) terminal on the first battery to the
positive (+) terminal on the second battery.
3.5.5 External DC Power Output Connections

Terminal TB10 provides two (2) power outputs, resettable and non-resettable. Each output is
power-limited. Follow sequence of steps in Section 3.2 “Installation Checklist”, Table 3.1; this is
part of Step 4.
Non-resettable Resettable
Power Power
CPU-320-DCOut.wmf
Figure 3.6 Power Supply DC Outputs - TB10
24 VDC Resettable Power Circuit (Four-Wire Smoke Detectors). The power supply
provides a single 24 VDC filtered, power-limited, resettable power circuit for devices that require
resettable power (such as four-wire smoke detectors). This circuit is power-limited, but must be
supervised. To provide supervision, install a UL-listed end-of-line power supervision relay (such
as the System Sensor model 1424, or the EOLR-1) after the last device. Connect the power
supervision relay normally open contact in series with an Initiating Device Circuit (IDC). The
four-wire power circuit energizes the power supervision relay. When you reset the system, the
control panel removes power from these terminals for approximately 15 seconds.

NAC Connections and Releasing Circuits Installation
Connect external field wires to the power supply terminals TB10 RESET(+) and (–) to provide up
to 1.25 A of current for powering four-wire smoke detectors. See Figure 3.6 above.
24 VDC Non-resettable Power Circuit The power supply provides one 24 VDC filtered,
power-limited, non-resettable power output, capable of up to 1.25 A. Use this circuit to power
devices that require low-noise 24 VDC power (such as Notifier annunciator model ACS-24AT or
the transmitter module TM-4).
Connect external field wires to power supply terminals TB10 NONRESET(+)and(–) to provide up
to 1.25 A of non-resettable current for powering external devices such as annunciators. See
Figure 3.6 above.
CAUTION:
! During system reset, power remains at terminals TB10 NONRESET(+)and(–).
3.6 NAC Connections and Releasing Circuits

The control panel provides four NAC terminals as shown in Figure 3.8. Each can be configured as
Style Y (Class B) or Style Z (Class A) as shown in Figure 3.7. Each circuit can provide 1.5 A of
current, but the total current drawn from the main power supply cannot exceed 7.4 A in alarm
condition (refer to Table A.2). NAC circuits are supervised and power-limited. Use UL-listed
24 VDC notification appliances only (refer to the Device Compatibility Document).
A–
TB9 - NAC#1 A+
B–
UL-listed ELR-2.2K,
B+
1/2 W (supplied)
A–
TB8 - NAC#2 A+
B–
B+
nfs640-nacout.cdr
B+ B– A+ A– B+ B– A+ A– B+ B– A+ A–
A–
TB7 - NAC#3 A+
B–
Unused Circuits Style Y (Class B) Style Z (Class A) B+
Connection Connection
Figure 3.7 Notification Appliance Circuit (NAC) A–

CPU-320-NACS.wmf
Connections TB6 - NAC#4 A+

B–
B+
Figure 3.8 NAC Terminals and NAC LEDs
NOTE: Any NAC can be programmed as a releasing circuit, and the releasing circuit must
be supervised; see Figure 4.6–Figure 4.8. For more information, refer to Section 4.5
“Releasing Applications” in this manual and the NFS-320/E/C Programming Manual. Refer to the
Device Compatibility Document for UL-listed compatible releasing devices. Sample connections
for NAC terminals are shown in Figure 3.7. Follow sequence of steps in Section 3.2 “Installation
Checklist”, Table 3.1; this is part of Step 4.

Installation Output Relay Connections
3.7 Output Relay Connections

The panel provides a set of Form-C relays. These
are rated for 2.0 A at 30 VDC (resistive):
• Alarm - TB4
• Trouble - TB4
• Supervisory - TB5
• Security - TB5
These are power-limited only if connected to a
power-limited source.
Using VeriFire Tools, the Supervisory and
CPU-320-relays.wmf
Security contacts can also be configured as Alarm
contacts. Follow instructions in the VeriFire
Tools online help.
Figure 3.9 Form-C Relay

Connections
3.8 Backup-Alarm Switches

WARNING:
! Do not enable the BACKUP option switch for any of the four Notification Appliance Circuits (NACs) if
they are used for releasing functions!
Backup alarm switches are provided that enable NACs

and the alarm relay to activate during a backup alarm
condition. If the main board’s microcontroller fails
CPU-320-bckalm.wmf
and an alarm is reported by any detector or a monitor
module that has backup reporting enabled, the NAC
will turn on if the corresponding switch was enabled.
The alarm will activate during microcontroller failure
regardless of the settings of switches SW1-SW4.
Figure 3.10 Backup Alarm
• SW1 - NAC#1 Switches
• SW2 - NAC#2
• SW3 - NAC#3
• SW4 - NAC#4
So, for example, if SW1 and SW4 were enabled at the time of an alarm during microcontroller
failure, NAC#1 and NAC#4 would activate. Follow sequence of steps in Section 3.2 “Installation
Checklist”, Table 3.1.

UL Power-limited Wiring Requirements Installation
3.9 UL Power-limited Wiring Requirements

Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All
power-limited circuit wiring must remain at least 0.25 inches (6.35 mm) from any
nonpower-limited circuit wiring. All power-limited and nonpower-limited circuit wiring must
enter and exit the cabinet through different knockout and or conduits. To maintain separation,
group non-power limited modules together, i.e., group modules on the same side of the enclosure or
in separate rows.
Figure 3.11 shows one configuration that meets these UL requirements. Equipment is configured
with at least a 0.25 inch (6.35 mm) separation between power-limited and nonpower-limited
wiring; AC and battery wiring is routed away from power-limited wiring.
Power-limited Circuits*
Power-
limited
circuits
Maintain vertical
separation where NPL
circuits appear to
“cross”
NPL
Nonpower-
limited
640-2-PWRLMTWIR-ISO2.wmf
circuits
To cabinet-mounted batteries
(nonpower-limited)
Figure 3.11 Typical Wiring for UL Power-limited Wiring Requirements

(Shown with relays as connected to power-limited modules)
NOTE: AC and battery wiring are not power-limited. Maintain at least 0.25 inches (6.35 mm)
between power-limited and non power-limited circuit wiring. Install tie wraps and adhesive squares
to secure the wiring. Use a power-limited source for relay output on terminals
TB5 and TB4.
See Figure 2.2, “CPU-320 and Power-Supply: Wiring Connections” on page 13 to identify
power-limited and non-powerlimited circuits.
NOTE: Drawing is not to scale; proportions and angles are exaggerated to show wire-placement
more clearly.

Installation Installing EIA-485 Devices
3.9.1 Labeling Modules and Circuits

At the time of installation, each nonpower-limited circuit connected to ACM-8R, and LDM-R32
modules must be identified in the space provided on the cabinet door label when connected to a
non-power-limited source of power.
The label lists all compatible power-limited modules and circuits; also see Figure 2.2 on page 13.
The LDM-R32 is power-limited only when connected to power-limited sources. When connected
to a non-power-limited source, the power-limited marking must be removed.
3.10 Installing EIA-485 Devices

Figure 3.12 provides a closer view of the EIA-485 connections provided on TB11. Because
specific connections can vary by the type of device being connected, refer to the product
installation manual for details.
cpu2-640tb200.wmf
Figure 3.12 EIA-485 Connections
3.11 Installing Remote Printers and/or CRT

3.11.1 Custom Cable Fabrication
A custom cable needs to be fabricated to connect the PRN Printer or the CRT-2 Monitor to the
system. Length of the cable will vary with each installation, but should not exceed a maximum
length of 20 feet (6.1 m). Printer must be installed in the same room as the panel, and the cable be
installed in conduit. Construct cable as follows:
1. Using overall foil/braided-shield twisted-pair cable, properly connect one end to the DB-25
Connector using the wiring specifications shown in the table below. (Custom cable kit
P/N 90106 is provided.)
2. Tighten clamp on connector to secure cable.
DB-25 Connector
TB12 on Control Panel
(Custom cable kit 90106)
Pin 3 TX
Pin 2 RX
Pin 7 REF

Installing Remote Printers and/or CRT Installation
3.11.2 Installing and Configuring the PRN Series Printer

When connected to the Control Panel via an EIA-232 interface, the PRN prints a copy of all status
changes within the control panel and time-stamps the printout with the time of day and date the
event occurred. It provides 80 columns of data on standard 9" by 11" tractor-feed paper.
NOTE: You can also use the EIA-232 printer interface with UL-listed information technology
equipment, such as personal computers, to monitor the control panel for supplementary
purposes.
This section contains information on connecting a printer to the control panel and for setting the
printer options.
Connecting a Remote PRN Series Printer
Remote printers require a 120 VAC, 50/60 Hz primary power source. If required for the fire alarm
system configuration (for example, a Proprietary Fire Alarm System), a remote printer requires a
secondary power source (battery backup). Because a secondary power source is not provided, use a
separate Uninterruptable Power Supply (UPS) that is UL-listed for Fire Protective Signaling. You
may use your building emergency power supply, so long as it meets the power continuity
requirements of NFPA 72. Refer to NFPA 72 for further details.
Connect the remote printer to the Control Panel as follows:
1. Connect the three (3) open leads of the custom cable to the TB12 terminal block on the control
panel as shown in Figure 3.13.
2. Plug the DB-25 connector end of the custom cable into the EIA-232 port of the remote printer.
Tighten securely.
Note: Outputs are power-limited

but are not supervised.
DB-25 connector on PRN
series printer (female
socket shown)
Terminate one end of
shield at backbox
CPU-320-prn.wmf
Control Panel
Figure 3.13 Remote Printer Connections
Setting Printer Options

Refer to the documentation supplied with the PRN series printer for instructions on using the
printer menu controls. Set the printer options (under the menu area) according to the settings listed
in Table 3.3.

Installation Installing Remote Printers and/or CRT
Option Setting Option Setting

Font HS Draft CPI 10 CPI
LPI 6 LPI Skip 0.5
ESC Character ESC Emulate Epson FX-850
Bidirectional Copy ON I/O
CG-TAB Graphic Buffer 40K
Country E-US ASCII Serial
Auto CR OFF Baud 9600, 4800, or 2400
Color Option Not Installed Format 7 Bit, Even, 1 Stop
Protocol XON/XOFF
Formlen
Character Set Standard
Lines 6LPI=60
Standard Exec 10.5 Sl.Zero On
Auto LF Off
PAPER
BIN 1 12/72"
BIN 2 12/72"
SINGLE 12/72"
PUSH TRA 12/72"
PULL TRA 12/72"
PAP ROLL 12/72"
Table 3.3 PRN Setup Options
3.11.3 Installing and Configuring a CRT-2

A CRT-2 can only be used in a non-networked application when used with the NFS-320/E/C. For
further details on setting up the CRT-2, refer to the NFS-320/E/C Operations Manual.
Connect a CRT-2 to the Control Panel as follows:
1. Connect the three (3) open leads of the custom cable to the TB12 terminal block on the control
panel as shown in Figure 3.14.
2. Plug the DB-25 connector end of the custom cable into the EIA-232 port of the CRT-2.
Tighten securely.
3. Set parameters as discussed in Table 3.14.
DB-25 connector
on CRT-2
(female socket shown)
Terminate one end of

shield at backbox
nfs640-crt2conn.cdr
Control
Panel
Figure 3.14 Connecting a CRT-2
Setting CRT-2 Parameters

The CRT-2 communicates with the control panel through a protocol defined by thirteen groups of
parameters. To access a parameter group, press the corresponding function key (F1-F12) as shown
in Table 3.4 below. You can then program parameters in each group.
Enter the CRT-2 setup menu by pressing and holding the <Ctrl> key while pressing the <Scroll
Lock> key. Use arrow keys to move through the selections in each setup group; press the space bar
to view the options for each parameter. When finished programming all setup groups, press the
<Pause> key. To save all changes, press <Y>.

Installing Remote Printers and/or CRT Installation
Table 3.4 shows the standard settings for using the CRT-2 with the NFS-320/E/C; for one instance
where these settings may change slightly see Section 3.11.4 “Connecting Multiple Printers, CRTs,
or CRT/PRN Combination”. The basic settings for using the CRT-2 with NFS-320/E/C are:
• Baud Rate 9600 • Data format 8 1 N • Protocol xon/off.
NOTE: This section covers installation only; for information on how the CRT-2 functions as part
of the fire alarm system, see the NFS-320/E/C Operations Manual.
NOTE: The CRT cannot be connected at the same time as the network.
Function Key CRT-2 Parameters

F1: Quick Emulation=CRT-2 EIA Baud Rate=9600 EIA Data Format=8/1/N
(“Read Status” key) Comm Mode=Full Duplex Aux Baud Rate=9600 Aux Data Format=8/1/N
Enhanced=On Language=U.S. Host/Printer=EIA/Aux
F2:Genrl Emulation=CRT-2 Enhanced=On Auto Wrap=Off
(“Alter Status” key) Auto Font Load=On Auto Page=Off Auto Scroll=On
Monitor Mode=Off Bell Volume=09 Warning Bell=On
Host/Printer=EIA/Aux
F3: Displ Page Length=24 Screen Length=26 Lines Screen Video=Normal
(“Prog” key) Display Cursor=On Cursor=Blink Line Auto Adjust Cursor=On
Columns=80 Width Change Clear=Off Speed=Normal
Scroll=Jump Refresh Rate=60 Hz Overscan Borders=Off
F4: Kybd Language=U.S. Char Set Mode=ASCII Key Mode=ASCII
(“Spl Funct” key) Keyclick=Off Key Repeat=Off Margin Bell=Off
Key Lock=Caps Keyboard Present=Yes
F5: Keys Enter Key=<CR> Return Key=<CR> Backspace=<BS>/<DEL>
(“Prior” key) Alt Key=Meta Disconnect=Pause Desk Acc=Disabled
Pound Key=U.S.
F6: Ports EIA Baud Rate=9600 EIA Data Format=8/1/N EIA Parity Check=On
(“Next” key) Aux Baud Rate=9600 Aux Data Format=8/1/N Aux Parity Check=On
EIA Xmt=Xon-Xoff EIA Recv=Xon-Xoff(XPC) EIA Xmt Pace=Baud
Aux Xmt=Xon-Xoff Aux Recv=Xon-Xoff(XPC) Aux Xmt Pace=Baud
EIA Break=Off EIA Modem Control=Off EIA Disconnect=2 sec
Aux Break=Off Aux Modem Control=Off Aux Disconnect=2 sec
F7: Host Comm Mode=Full Duplex Local=Off Recv <CR>=<CR>
(“Auto Step” key) Recv <DEL>=Ignore Send ACK=On Send Line Term=<CR><LF>
Send Block Term=<CR> Null Suppress=On
F8: Print Prnt Line Term=<CR><LF> Prnt Block Term=<CR> Secondary Recv=Off
(“Activ Signal” key)
F9: Emul Attribute=Page Bright Video=Off Page Edit=Off
WPRT Intensity=Dim WPRT Reverse=Off WPRT Underline=Off
WPRT Blink=Off Display NV Labels=Off Save Labels=On
Status Line=Off Fkey Speed=Normal
F10 Setup Group F10 does not affect communications with the control panel.
F11 Setup Group F11 does not affect communications with the control panel.
F12: Prog Program the function keys as follows: F1 ~A F2 ~B F3 ~C F4 ~D F5 ~E F6 ~F F7 ~G
(“Ack Step” key) F8 ~H F9 ~I F10 ~J F11 ~K F12 ~L F13 ~M F14 ~N F15 ~O F16 ~P Shift F13 ~Q
Table 3.4 Standard CRT-2 Settings for Use with NFS-320/E/C
3.11.4 Connecting Multiple Printers, CRTs, or CRT/PRN

Combination
Connecting multiple devices requires changing the CRT-2 setup using the F1(Quick) menu:
• Set Host/Printer=EIA/AUX.
• Set EIA Data Format=8/1/N.
• If the AUX device is a printer, set the Printer and AUX Data Format=7/1/E.
• If the AUX device is a second CRT-2, set the AUX Data Format=8/1/N.

Installation Wiring a Signaling Line Circuit (SLC)
Connect multiple devices as shown in Figure 3.15.

To Control Panel
TB12-PC/CRT REF
TB12-PC/CRT TX
7 3 2 7 3 2 TB12- PC/CRT RX
To AUX Port of CRT-2 To EIA-232 port of CRT-2

(female socket shown) (female socket shown)
prncrt-conn.cdr
7 3 2
To EIA-232 port of next
CRT-2 or PRN (female socket shown)
Note: For wire requirements, see Table B.1 in Appendix B “Electrical Specifications”.
Figure 3.15 Connecting Multiple Devices on the EIA-232 Circuit
3.12 Wiring a Signaling Line Circuit (SLC)

Overview
Communication between the control panel and intelligent and addressable initiating, monitor, and
control devices takes place through a Signaling Line Circuit (SLC). You can wire an SLC to meet
the requirements of NFPA Style 4, Style 6, or Style 7 circuits.
This manual provides requirements and performance details specific to this control panel; for
installation information and general information, refer to the SLC Wiring Manual.
Wiring
Maximum wiring distance of an SLC using 12 AWG (3.31 mm2) wire is 12,500 feet (3810 meters)
total twisted-pair for Style 4, Style 6 and Style 7 circuits.
Capacity
The NFS-320/E/C provides one (1) SLC, with a total capacity of 318 intelligent/addressable
devices:
• 01-159 intelligent detectors
• 01-159 monitor and control modules
Units employing multiple detector operation shall include a minimum of two detectors in each
protected space and reduce the detector installation spacing to 0.7 times the linear spacing in
accordance with National Fire Alarm Code, NFPA. For spacing requirements refer to the detector’s
installation instructions.
NOTE: To meet the ten-second response time required by UL 864, 9th edition, when SLC loops
are configured to run in CLIP mode, all input modules must be mapped to address 19 and lower
on both loop one and 2. There are no limits to detectors or output modules.
Installation
This control panel supports one SLC loop, which connects to TB13 on the control panel. For
details on designing, installing and configuring SLC loops, see the SLC Wiring Manual.

Connecting a PC for Off-Line Programming Installation
SLC B SLC A
nfs640-slcloops.cdr, CPU-320-SLC-TB.wmf
SLC B (output loop)
SLC A (loop return)
SLC Loop Connections

on FACP’s main circuit board
B+ A+ B- A- TB13 on B+ A+ B- A-
NFS-320/E/C
Style 4 SLC Loops Style 6 SLC Loops
Note: T-Tapping is not allowed on a four-wire SLC.
Figure 3.16 SLC Loop Connections and Wiring
3.13 Connecting a PC for Off-Line Programming

A PC can be hooked up to the control panel to allow the VeriFire Tools programming utility to
upload and download the operating program. Refer to the insert in the VeriFire Tools CD and to the
program’s on-line help function for instructions. There are two options for connection:
Two options are available.
1. For PCs with USB Ports, connect the PC to USB B via a standard USB B cable.
2. For PCs without USB Ports, connect the PC’s serial port to the Control Panel’s
Network/Service Connection (J1, NUP).
NOTE: Download operations that change the basic program of the control panel must be
performed by responsible service personnel in attendance at the control panel. After downloading
a program, test the control panel in accordance with NFPA 72.

Section 4: Applications
4.1 Overview
Chapter Covers the following topics
Section 4.2 “NFPA 72 Central or How to install UDACT with the control panel for use as a NFPA Central
Remote Station Fire Alarm System or Remote Station Fire Alarm System (Protected Premises Unit)
(Protected Premises Unit)”
Section 4.3 “NFPA 72 Proprietary How to set up a Protected Premises Unit to communicate with a listed
Fire Alarm Systems” compatible Protected Premises Receiving Unit.
Section 4.4 “Fire/Security How to use the control panel as a combination Fire/Security system,
Applications” including the following:
• Installing a Security Tamper Switch into the cabinet
• Circuit Wiring
Section 4.5 “Releasing How to install the following releasing applications:

Applications” • Releasing Device to the Control Panel (NAC integral circuits)
• Releasing Device to the FCM-1 Module
• NBG-12LRA Agent Release-Abort Station
Municipal Box (Auxiliary)

Municipal Box applications require a TM-4 Transmitter module. Refer to the TM-4 Transmitter
Module installation document for installation details.
4.2 NFPA 72 Central or Remote Station Fire Alarm System

(Protected Premises Unit)
Figure 4.1 shows typical wiring diagram for a NFPA 72 Central Station Fire Alarm System
(Protected Premises Unit) or a Remote Station Fire Alarm System (Protected Premises Unit) using
the Universal Digital Alarm Communicator/Transmitter (UDACT) and control panel. This
provides typical wiring only; connect and program the UDACT according to the directions given in
the UDACT Instruction Manual.
NOTE: An NFPA 72 Central Station or Remote Station requires 24 hours of standby power and 5
minutes in alarm.
NOTE: This application can also be done with the TM-4 Transmitter; refer to the TM-4
Transmitter Module installation document for more details.

NFPA 72 Proprietary Fire Alarm Systems Applications
Ferrite cores
FACP Cabinet P/N 29090
To supervised Solid earth

phone lines ground
24 VDC EIA-485
Nonresettable power (ACS Mode)
Supervised and power-limited

EIA-485 and power wiring
CPU-320-udact.wmf
UDACT in ABS-8RB
(shown with cover removed)
Figure 4.1 Typical Wiring Diagram for a Central Station Fire Alarm System
NOTE: Install a UL-listed 120 ohm End-of-Line resistor (P/N 71244) UDACT TB1 terminals 3
and 4 if this is the last or only device on EIA-485 line.
4.3 NFPA 72 Proprietary Fire Alarm Systems

When connected and configured as a protected premises unit with UDACT, the NFS-320/E will
automatically transmit General Alarm, General Trouble, and General Supervisory signals to a listed
compatible Protected Premises Receiving Unit. See the UDACT Manual for compatible receiving
units. A simplified drawing of connections between the receiving unit and the NFS-320/E
protected premises unit is shown in Figure 4.2.
Connect the receiving unit to the protected premises unit as shown in Section 4.2 “NFPA 72 Central
or Remote Station Fire Alarm System (Protected Premises Unit)”.
For information on installing and programming the Receiving unit, refer to the documentation for
that control panel.

Applications Fire/Security Applications
Telephone line and backup
UDACT
Compatible Receiving Unit

(see UDACT Manual) NFS-320/E
NFS-320/E
Protected Premises Unit
Figure 4.2 Typical Proprietary Fire Alarm Systems Wiring Connections
4.4 Fire/Security Applications

NOTE: NFS-320/E/C is not approved for use in security applications in Canada.
4.4.1 General Operation

The control panel can be used as a combination Fire/Security system when installed and operated
according to the instructions in this section.
For security applications, program one or more monitor modules (listed for security applications)
with the SECURITY Type Code, and wire as shown in Figure 4.4. Activating this type of module
lights the SECURITY LED, and displays a security alarm condition on the control panel LCD display.
The panel sounder will sound until the Security alarm is acknowledged. You can also program
additional sounders or output devices to activate with the security alarm initiating device. The
SECURITY Type Code is designed to indicate an alarm as follows: (a) on an open or short circuit; or
(b) on a ±50% change in resistance value from the End-of-Line resistor value.
A tamper switch installed in the cabinet door will indicate a door tamper condition whenever the
door is open. If the control panel indicates a Security alarm, you can acknowledge, silence, and
reset the condition from the control panel.
When the system resets, a 30-second exit timer starts. During this time the tamper switch and all
Security alarms are ignored. There is no entrance delay timer.
For bypass of security zones, use the DISABLE routine (covered in the Status Change section of
the NFS-320/E/C Operations Manual) for Security type devices.
WARNING:
! Damage can result from incorrect wiring connections.

Fire/Security Applications Applications
4.4.2 Installing a Security Tamper Switch

To wire the cabinet with a Security Tamper Switch kit model STS-1, refer to Figure 4.3:
1. Install the STS-1 Tamper Switch into the location shown in Figure 4.3. Push the switch
through the opening until it snaps into place.
2. Install the magnet on the corresponding location in the cabinet door. Push the magnet through
the opening in the door until it snaps into place.
3. Connect the STS-1 connector to J5 (Security Tamper) on the Control Panel. (As shown in
Figure 4.3, J5 is located on the circuit board, underneath the edge of KDM-R2.)
STS-1 mounting location
Connect to
J5 “Security Tamper”
320_STS1.wmf
Figure 4.3 Installing the STS-1 Security Tamper Switch
4.4.3 Receiving Unit

For applications requiring transmission of security alarm information to a central receiving unit, the
control panel may be connected via the UDACT to a compatible receiving unit (see the UDACT
Manual). For information on configuring the Receiving unit for Combination Fire/Security
applications, refer to the documentation for that control panel.
4.4.4 Programming
The control panel can communicate with any number of security devices. To do so, program the
points as follows:
1. Select the address of the module(s) to be used for security.
2. Select the Type Code SECURITY.
NOTE: For detailed instruction on programming Type Codes, refer to the NFS-320/E/C
Programming Manual.

Applications Fire/Security Applications
4.4.5 Wiring for Proprietary Security Alarm Applications

Table 4.4 shows typical wiring for proprietary security alarm applications with FMM-1 modules.
Note the following:
• The module is programmed with software SECURITY Type Code.
• For use with UL listed systems only; application not for ULC security usage.
• NAC devices used for security cannot be shared with fire NAC devices.
• Refer to the Device Compatibility Document for compatible NAC devices.
• All monitor modules used for security application must be installed in the NFS-320/E cabinet
with STS-1 Security Tamper Switch.
NFS-320//E Protected Premises Unit
UL-listed 47K UL-listed,

End-of-Line Resistor normally-open
(provided with module) security switch
SLC
Channel
A or B
CPU-320-burg.wmf
UL-listed, normally-closed
security switch
FlashScan Monitor Module
Figure 4.4 Wiring Diagram for Proprietary Security Alarm Applications

Releasing Applications Applications
4.5 Releasing Applications

WARNING:
! When used for CO2 releasing applications, observe proper precautions as stated in NFPA 12.
Do not enter the protected space unless physical lockout and other safety procedures are fully
completed. Do not use software disable functions in the panel as lockout.
WARNING:
4.5.1 Overview
This control panel can be used for agent release or preaction/deluge control applications. In a
properly configured system with compatible, listed actuating and initiating devices, this control
panel complies with the following NFPA standards for installation in accordance with the
acceptable standard:
Standard Covers
NFPA 12 CO2 Extinguishing Systems
NFPA 12A Halon 1301 Extinguishing Systems
NFPA 13 Sprinkler Systems
NFPA 15 Water Spray Systems
NFPA 16 Foam-Water Deluge and Foam-water Spray Systems
NFPA 17 Dry Chemical Extinguishing Systems
NFPA 17A Wet Chemical Extinguishing Systems
NFPA 2001 Clean Agent Fire Extinguishing Systems
Table 4.1 NFPA Standards for Releasing Applications
4.5.2 Programming
The control panel supports up to ten releasing software zones. You can map these zones to activate
Control Panel releasing outputs and FCM-1 modules. Program the FCM-1 module for the
appropriate type code according to the chart below:
Type Code: RELEASE CKT Type Code: REL CKT ULC

• For use in UL applications. • For use in UL or ULC applications.
• Do not use REL device at the solenoid. • Requires REL device at solenoid.
• Cannot use power-limited wiring. • Power-limited wiring.
• Supervised for open circuit only. • Supervised for open circuit and shorts.
• Supervised for power loss with • Supervised for power loss with
power-supervision relay. power-supervision relay.
For more information, refer to the NFS-320/E/C Programming Manual.
4.5.3 Wiring
References to wiring diagrams for releasing applications:
To connect Refer to
A releasing device to the control panel. Section 4.5.4 “Connecting a Releasing Device to the Control Panel”.
A releasing device to the FCM-1 Module. Section 4.5.5 “Connecting a Releasing Device to the FCM-1 Module”.
An NBG-12LRA Agent Release-Abort Station. Section 4.5.6 “Connecting an NBG-12LRA Agent Release-Abort Station”.

Applications Releasing Applications
4.5.4 Connecting a Releasing Device to the Control Panel

Use TB6 (NAC#4), TB7 (NAC#3), TB8 (NAC#2), or TB9 (NAC#1) on the control panel for
NAC⁄Releasing Circuits. The releasing circuit must be supervised and use listed, compatible
releasing devices; see Figure 4.6–Figure 4.8 (page 41).
B+ NAC/Releasing output (source)

B– NAC/Releasing output (source)
A+ Class A (return for NAC only)
A– Class A (return for NAC only)
Compatible UL-listed
24 VDC releasing device
CPU-320-RELCONN1.wmf
Control
Panel
REL-2.2K (Use with Type Code

Rel Ckt ULC, or see Circuit
Note: See text below for circuit requirements. Requirement 4.)
Figure 4.5 Typical Style 4 Connection of a Releasing Device to Control Panel
WARNING:
Circuit Requirements. When connecting a releasing device, note the following:

1. The control panel provides four NAC/Releasing Circuits (Style Y or Z). Each circuit can
provide 1.5 A. Total current drawn from the power supply cannot exceed 7.4 A in an alarm
condition (refer to Table A.2, “System Draw Current Calculations,” on page 48). Use
compatible UL-listed 24 VDC appliances only. For more information on compatible
appliances, refer to the Device Compatibility Document.
2. Refer to the Releasing Applications appendix in the NFS-320/E/C Programming Manual for
configuration details (such as setting the Soak Timer).
3. For applications using power-limited circuits:
a) Use an in-line supervisory device (P/N REL-2.2K) with control panel releasing circuits.
Connect the End-of-Line device as shown in Figure 4.5.
b) Program the releasing circuit for Type Code REL CKT ULC.
c) Circuits are supervised against opens and shorts.
4. For applications not requiring power-limited circuits –
a) If the application does not require supervising the releasing device against shorts, in-line
supervisory devices (P/N REL-2.2K) are not required.
b) In non-power-limited applications, program the releasing circuit for Type Code
RELEASE CKT.
c) Limited energy cable cannot be used to wire a non-power-limited releasing device circuit
d) Maintain a 0.25 inch (6.35 mm) spacing between the non-power-limited releasing circuit
device wiring and any power-limited circuit wiring.)
5. The releasing circuit must be programmed with a releasing type code listed in the
NFS-320/E/C Programming Manual.

IQActuatorsa.wmf
Figure 4.6 Releasing Circuits (Option 1)
IQActuatorsb.wmf
Figure 4.7 Releasing Circuits (Option 2)
IQActuatorsb.wmf
Figure 4.8 Releasing Circuits: Option 3

Applications Releasing Applications
4.5.5 Connecting a Releasing Device to the FCM-1 Module

The module can control 1 A of current. Make sure to keep total system current within the limits of
the power supply. You can power the module from the power supply of the Control Panel or any
UL/ULC listed 24 VDC regulated power-limited power supply for Fire Protective Signaling. For
more information, refer to the Device Compatibility Document.
SLC from FACP
+
–
– +
Compatible UL-listed
24 VDC releasing device 9 0
6 7 8 9 10
5
8
4
3
11
12 1 Non-resettable
– 7
2
TENS
1 0 1514
13
2 24 VDC Power
6789
Brown Red 6 4
3
5
3 –
+ 5
2
10
4
+
Relconn-fcm.cdr
REL-47K ONES
ADDRESS
LOOP
(Use with Type Code
Rel Ckt ULC, N.C. Supervision
or see Circuit
Relay Contact Power Supervision
Requirement 3.)
Part of EOLR-1 Relay (EOLR-1)
FCM-1
Note: See text for circuit requirements.
Figure 4.9 Typical Connection of a 24 VDC Releasing Device to the FCM-1 Module
Circuit Requirements When connecting a releasing device to the FCM-1 module, note the
following:
1. Refer to the Releasing Applications appendix in the NFS-320/E/C Programming Manual for
configuration details (such as setting the Soak Timer).
2. For applications using power-limited circuits:
a) Use an in-line supervisory device (P/N REL-47K) with the FCM-1 module. Connect the
in-line supervisory device as shown in Figure 4.9.
b) Program the releasing circuit for Type Code REL CKT ULC.
c) Circuits are supervised against opens and shorts.
3. For applications not requiring power-limited circuits:
a) In-line supervisory devices (P/N REL-47K) are not required; however, the releasing device
circuit is not supervised against shorts.
b) In non-power-limited applications, program the releasing circuit for Type Code
RELEASE CKT.
c) Limited energy cable cannot be used to wire a non-power-limited releasing device circuit.
d) Maintain a 0.25 inch (6.35 mm) spacing between the non-power-limited releasing circuit
device wiring and any power-limited circuit wiring.
WARNING:
! The XP6-C is not listed for releasing applications and cannot be substituted for FCM-1.

4.5.6 Connecting an NBG-12LRA Agent Release-Abort Station

SLC loop to
FACP
NBG-12LRA Manual Abort Yellow FMM-101
Black
See Document 51369 – – –
for installation details.
Violet Red
+ + +
Manual Release Yellow Black

FMM-1
– –
Violet Red
+ +
Normal Non-resettable +24 VDC
from main power supply
ELR mode R-47K Release
supervised and
–
NBG640-NBG12LRA.cdr
power-limited 1
FRM-1
6 2 +
C.
5 4
N.C. N.O.
System
Common (–)
24 VDC power
from FACP’s
0
main power supply
24 VDC UL-listed 7-
FCM-1
1 –
releasing device 2
+
6+ 3– –
Brown Red N.C. Supervision 4 +
REL-47K Relay Contact +
(use with Type Code
Rel Ckt ULC)
Power Supervision
Relay (EOLR-1)
Figure 4.10 Typical Connections for an NBG-12LRA Agent Release-Abort Station
NOTE: If using the on-board NACs, see Circuit Requirements for Section 4.5.4 “Connecting a
Releasing Device to the Control Panel” on page 40. If using FCM-1, see Circuit Requirements for
Section 4.5.5 “Connecting a Releasing Device to the FCM-1 Module” on page 42.

Section 5: Testing the System
5.1 Acceptance Test

When finished with the original installation and all modifications, conduct a complete operational
test on the entire installation to verify compliance with applicable NFPA standards. Testing should
be conducted by a factory-trained fire alarm technician in the presence of a representative of the
Authority Having Jurisdiction and the owner’s representative. Follow procedures outlined in
NFPA Standard 72’s section on Inspection, Testing and Maintenance.
5.2 Periodic Testing and Service

Periodic testing and servicing of the control panel, all initiating and notification devices, and any
other associated equipment is essential to ensure proper and reliable operation. Test and service the
control panel according to the schedules and procedures outlined in the following documents:
• NFPA Standard 72’s section on Inspection, Testing and Maintenance.
• Service manuals and instructions for the peripheral devices installed in the system. Correct
any trouble condition or malfunction immediately.
5.3 Operational Checks

Between formal periodic testing and servicing intervals, the following operation checks should be
performed monthly, or more frequently when required by the Authority Having Jurisdiction.
Before proceeding: a) notify the fire department and the central alarm receiving station if
transmitting alarm conditions; b) notify facility personnel of the test so that alarm sounding
devices are disregarded during the test period; and c) when necessary, disable activation of
alarm notification appliances and speakers to prevent their sounding.
Disconnect all releasing devices to prevent accidental activation in accordance with NFPA
2001 and NFPA 12A releaseing agents..
WARNING:
! Do not rely on disable/enable software settings to lockout releasing devices.
Check that the green POWER LED lights.

Check that all status LEDs are off.
Press and hold the LAMP TEST key. Verify that all LEDs and all LCD display segments work.
Activate an Initiating Device Circuit using an alarm initiating device or an addressable
initiating device on the SLC and check that all programmed active notification appliances
function. Reset the alarm initiating device, the control panel, and any other associated
equipment. Select the paging function and confirm that the message can be heard in the
affected fire zones. Repeat the above step with each Initiating Device Circuit and each
addressable device.
Remove AC power, activate an Initiating Device Circuit through an alarm initiating device or
an addressable initiating device on the SLC, and check that programmed active notification
appliances sound, and alarm indicators illuminate. Measure the battery voltage with
notification appliances active. Replace any battery with a terminal voltage less than 21.6 VDC
Continued on next page...

Battery Checks and Maintenance Testing the System
and reapply AC Power.
NOTE: The battery test requires fully charged batteries. If batteries are new or discharged due
to a recent power outage, allow the batteries to charge for 48 hours before testing.
Return all circuits to their pretest condition.

Check that all status LEDs are off and the green POWER LED is on.
Notify fire, central station and/or building personnel when you finish testing the system.
5.4 Battery Checks and Maintenance

Maintenance-free sealed lead-acid batteries used in the system do not require the addition of water
or electrolyte. These batteries are charged and maintained in a fully charged state by the main
power supply’s charger during normal system operation. A discharged battery typically reaches the
voltage of 27.6 VDC within 48 hours; the charge rate depends on the battery size (1.5A-2.0A for
18-26AH; 5.0A-5.7A for 26AH-200AH).
Sealed lead-acid batteries must be replaced within at most 5 years from their date of manufacture.
Minimal replacement battery capacity appears on the control panel marking label. Immediately
replace a leaking or damaged battery. You can get replacement batteries from the manufacturer.
WARNING:
! Batteries contain Sulfuric Acid which can cause severe burns to the skin and eyes and damage to
fabrics.
• If a battery leaks and contact is made with the Sulfuric Acid, immediately flush skin and/or
eyes with water for at least 15 minutes. Water and household baking soda provides a good
neutralizing solution for Sulfuric Acid.
• If Sulfuric Acid gets into eyes, seek immediate medical attention.
• Ensure proper handling of the battery to prevent short circuits.
• Take care to avoid accidental shorting of the leads from uninsulated work benches, tools,
bracelets, rings, and coins.
WARNING:
! Shorting the battery leads can damage the battery, equipment, and could cause injury to personnel.

Appendix A: Power Supply Calculations
Calculations must be done to determine standby and alarm DC current loads. Ampere-hour
requirements must be calculated as well to determine battery size.
The KAPS-24/E power supply provides filtered 24VDC power that may be used for operating
external devices. Use Table A.2 to determine if external loading is within the capabilities of the
power supply.
A.1 Calculating AC Branch Circuit Current

Use Table A.1 below to determine the total amount of current, in AC amperes, that a 120 VAC,
50/60 Hz service must be able to supply to the fire alarm system. Devices rated for 240 VAC
operation will draw approximately one-half the current listed in Table A.1.
Device Type No. of Devices Current (amps) Total Current

KAPS-24/E Power Supply [ 1 ] X 5.0 = 5.0
FCPS-24S6/S8 [ ] X 3.2 =
ACPS-2406 [ ] X 2.7* =
APS-6R [ ] X 2.5 =
CHG-120 [ ] X 2.0 =
Sum column for AC Branch Current required=amps
Table A.1 120 VAC Fire Alarm Circuit

* Separate calculations are required for any devices powered by the
ACPS-2406. It has its own integral battery charger and batteries can be
connected directly to it. Refer to the ACPS-2406 Installation Manual for its
battery calculations.
AC Branch Circuit Installation

For guidelines on wiring the AC branch circuit current, see “Operating Power: AC Branch Circuit”
on page 53 in Appendix B.1 “Electrical Specifications”.
A.2 Calculating the System Current Draws

The control panel’s main power supply must be able to power all internal system devices (and
several types of external devices) continuously during non-fire alarm conditions. Use column 1 in
Table A.2 to calculate the Non-Fire Alarm Load on the power supply regulator when applying
primary power. The main power supply must also provide a finite amount of additional current
during a fire alarm condition. Use column 2 in Table A.2 to calculate the additional current needed
during fire alarms. The requirements for non-fire alarm and fire alarm current loads cannot exceed
the capabilities of the power supply as listed below:
• 3.9 A at 24 VDC during Standby; and
• 7.4 A at 24 VDC during Alarm.
How to Use the Calculating Tables
As used in this section, “Primary” refers to the control panel’s on-board power supply, its primary
source of AC power. “Secondary” refers to the control panel’s backup batteries (or any other 24
VDC power supply listed for Fire Protective Signaling and connected in place of the batteries).
The term “standby” refers to the output current required when no fire alarm is present. The term
“alarm” refers to the output current required when a fire alarm is present.
The Primary Power Source Non-Alarm Current and Alarm Current columns are DC current
calculations. These calculations confirm that the power supply can provide enough current to
support the system during Primary Non-Fire Alarm and Fire Alarm conditions.

Calculating the System Current Draws Power Supply Calculations
Quantities List the number of devices powered by the FACP and its power supply. Devices
powered by the Accessories Output (TB9) draw current directly from the panel. Devices powered
by the Panel Output draw current through the fire panel’s connection to the power supply. Use
these quantities to calculate total current draw of each set of devices in calculation columns 1, 2,
and 3.
Calculation Column 1 (Primary, Non-Fire Alarm Current in amps) Add the contents of
calculation column 1 to get the current drawn from the power supply during a non-alarm condition,
with AC power applied. This current draw cannot exceed 3.9 A without an auxiliary power supply.
Calculation Column 2 (Primary, Fire Alarm Current in amps) Calculation column 2 lets
the system designer determine the current load that the power supply must support during a fire
alarm. The total current draw during a fire alarm cannot exceed 7.4 A without an auxiliary power
supply.
Typically, a system should contain capacity to activate all output circuits and relays, and support
fire alarms on no less than 10% of Initiating Device Circuits, subject to the requirements of the
Authority Having Jurisdiction (AHJ).
The Control Panel provides power for Notification Appliance Circuits. Refer to the Device
Compatibility Document for 24 VDC notification appliances that are UL- and ULC-listed for fire
alarm systems.
Calculation Column 3 [Secondary (Battery) Non-Alarm Current] Column 3 lets the
system designer calculate the non-fire alarm current drawn from the secondary source in a non-fire
alarm condition during AC power loss.The non-fire alarm current is required to complete the
standby battery calculations. After summing all current draws, insert the total in Table A.3.

Power Supply Calculations Calculating the System Current Draws
Calculation Column 1 Calculation Column 2 Calculation Column 3

Category Primary, Non-Fire Alarm Primary, Fire Alarm Secondary, Non-Fire Alarm
Current (amps) Current (amps) Current (amps)
Qty X [current draw]= Total Qty X [current draw]= Total Qty X [current draw]= Total
CPU-320/E 1 x [0.250] = 1 x [0.250] = 1 x [0.250] =
# NACs in use (0, 1, 2, 3 or 4)* [ ] x [0.035] [ ] x [0.035] [ ] x [0.035]
KAPS-24/E n/a n/a n/a n/a 1 x [0.040]
KDM-R2 (Backlight on) [ ] x [0.100]= [ ] x [0.100]= [ ] x [0.100]=
SLC loop†: 1 1 1
with jumper JP2 cut on CPU x [0.200]= x [0.200]= x [0.200]=
or without jumper JP2 cut on CPU x [0.400]= x [0.400]= x [0.400]=
NCA, NCA-2 Back-light ON [ ] x [0.400]= [ ] x [0.400]= [ ] x [0.400]=
NCA, NCA-2 Back-light OFF [ ] x [0.200]= [ ] x [0.200]= [ ] x [0.200]=
NCM-W, NCM-F [ ] x [0.110]= [ ] x [0.110]= [ ] x [0.110]=
TM-4 [ ] x [0.110]= [ ] x [0.175]= [ ] x [0.110]=
DPI-232 (Refer to manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
APS-6R [ ] x [0.025]=
ACPS-2406 [ ] x [0.0013]=
ACM-24AT [ ] x [0.016]= [ ] x [0.070]= [ ] x [0.016]=
ACM-48A [ ] x [0.016]= [ ] x [0.070]= [ ] x [0.016]=
AEM-24AT [ ] x [0.002]= [ ] x [0.056]= [ ] x [0.002]=
AEM-48A [ ] x [0.002]= [ ] x [0.056]= [ ] x [0.002]=
Maximum number of LEDs illuminated on [ ] x [0.0054]= [ ] x [0.0054]=
these annunciators during non-fire
conditions:
AFM-16AT, AFM-32A [ ] x [0.040]= [ ] x [0.056]= [ ] x [0.040]=
ACM-16AT, ACM-32A [ ] x [0.040]= [ ] x [0.056]= [ ] x [0.040]=
AEM-16AT, AEM-32A [ ] x [0.002]= [ ] x [0.018]= [ ] x [0.002]=
AFM-16A [ ] x [0.025]= [ ] x [0.065]= [ ] x [0.025]=
ACM-8R (refer to manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
LDM (refer to manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
FDU-80 [ ] x [0.0643]= [ ] x [0.0643]= [ ] x [0.0643]=
FZM-1, MMX-2 [ ] x [0.0094]= [ ] x [0.090]= [ ] x [0.0094]=
RPT-W, RPT-WF, RPT-F [ ] x [0.017]= [ ] x [0.017]= [ ] x [0.017]=
RPT-485W, RPT-485WF
UDACT Communicator [ ] x [0.040]= [ ] x [0.100]= [ ] x [0.040]=
NFV-25/50 (see manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Four-Wire Smoke Detectors‡ [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
[ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Power Supervision Relay [ ] x [0.020]= [ ] x [0.020]= [ ] x [0.020]=
EOLR-1 or A77-716B
Notification Appliance powered from Main [ ] x[ ]=
Power Supply** [ ] x[ ]=
DHX-501, FSD-751RP, FSD-751RPL [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
(Duct Detectors with internal relays) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Refer to installation document
CHG-120 Battery Charger [ ] x [0.060]=
Local Energy Municipal Box [ ] x[ ]=
Compatable Devices not listed above†† [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
[ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Sum each column for totals Primary, non-alarm: Primary, alarm: Secondary, non-alarm:
Table A.2 System Draw Current Calculations

* Maximum current draw for all NACs plus DC output from TB10 is 3.0 A during standby.
† Value represents an SLC’s maximum current draw. Refer to device datasheets for individual current draws. If jumper JP2 is cut, total device current cannot
exceed 200 mA; if jumper JP2 is not cut, total device current cannot exceed 400 mA.
‡ The total regulated load current supplied to four-wire smoke detector and power supervision relays cannot exceed 1.25 A.
** Enter the total notification appliance draw from the Main Power Supply, excluding the current from APS-6R supplies. Refer to Device Compatibility Document.
†† Refer to manual and/or Device Compatibility Document. See Table 1.1, “Reference Documentation,” on page 8 for specific documentation part numbers.

Calculating the System Current Draws Power Supply Calculations
A.2.1 Calculating the Maximum Secondary Power Fire Alarm

Current Draw
Use Table A.3 below to determine the maximum current requirements of secondary power source
during fire alarm conditions. The result obtained is the amount of current that the batteries must be
able to supply to the fire alarm system. Use the result in Table A.4 to determine the size of the
batteries needed for the fire alarm system.
Results taken from Table A.3 below assume that, while in a fire alarm condition, batteries must
feed the main power supply (and any additional supplies such as the APS-6R) with the maximum
rated power each supply can provide.
Current
Device Quantity Total Current/Type
(in amps)
Alarm Current, from Table A.2, col 2 =
APS-6R* [ ] X 6 =
Sum Column for Secondary Fire Alarm Load =
Table A.3 Maximum Secondary Power Fire Alarm Current Draw

* Actual load current may be used in place of maximum rated supply
current. To calculate actual load current, sum the current draws for
each appliance connected to APS-6R supplies.
NOTE: The Secondary Fire Alarm Load cannot exceed the following:
• 12 A with BAT-12250 batteries (12 V, 26 AH).
• 20 A with BAT-12550 batteries (12 V, 55 AH).

Power Supply Calculations Calculating the Battery Requirements
A.3 Calculating the Battery Requirements

A.3.1 Calculating the Battery Capacity
Use this table to determine the battery capacity needed for the system:
Current (amps) X Time (hours) = AH
Secondary Non-Fire Alarm Current Required Secondary Non-Fire Alarm

(from column 3 in Table A.2) Standby Time (24 or 60 hours)
(see Note 8)
X ________________ = _________AH
________________
APS-6R Required Secondary Non-Fire Alarm

Standby Load Current Standby Time (24 or 60 hours)
________________ X ________________ = _________AH
Secondary Fire Alarm Load Required Fire Alarm Standby Time:

(from Table A.3) (for 5 minutes, enter 0.084; for 15
(see Note 8) minutes, enter 0.25)
________________ X ________________ = _________AH

Sum Column for Total Secondary Amp Hours calculated = _________AH
Multiply by the derating factor x 1.2 (see Note 7) = _________AH
Battery Size – Total Secondary Amp Hours Required = _________AH

1. NFPA 72 Local, Proprietary, and Central Station systems requires 24 hours of standby power followed by
5 minutes in alarm.
2. NFPA 72 Auxiliary and Remote Station Systems require 24 hours of standby power followed by 5 minutes
in alarm.
3. Batteries installed in a system powered by an automatic starting engine generator need to provide at
least 4 hours of standby power.
4. Factory Mutual requires 90 hours of standby for deluge-preaction systems.
5. Emergency voice/alarm communications systems require 2 hours of operation in the alarm condition.
Due to the sporadic nature of voice operation, however, NFPA 72 permits 15 minutes of operation at a
maximum connected load to equal 2 hours of normal use.
6. If the total exceeds 26 AH, the system requires a separate NFS-LBB battery enclosure for two
BAT-12550, 55 AH batteries in a separate NFS-LBB enclosure. If the total exceeds 55 AH, the system
requires an auxiliary battery charger with sufficient amp-hour capacity; this charger must be UL-listed for
Fire-Protective Signaling. If CHG-120 battery charger is used, it requires a second NFS-LBB enclosure.
7. The following battery derating factors must be used for Canadian installations using NFS-320C charger:
• For a 26 AH battery, use derating factor of 1.5
When batteries are charged by CHG-120 charger use a derating factor of 1.2 for 26 AH and 55 AH
batteries.
8. For 26 AH batteries: maximum standby current cannot exceed 0.65A; maximum alarm current cannot
exceed 6.75A.
Table A.4 Secondary Power Standby and Fire Alarm Load

Calculating the Battery Requirements Power Supply Calculations
A.3.2 Calculating the Battery Size

Use this table to choose the battery size, in amp-hours, needed to support the fire alarm system.
The KAPS-24/E can charge batteries from 18 to 200 AH. Select batteries that meet or exceed the
Total Amp-Hours calculated in Table A.4 and that are within the acceptable battery charger range.
Write the amp-hours requirements on the Protected Premises label.
The maximum battery size that can be mounted inside the NFS-320’s cabinet is 26AH.
Voltage Number Our Part

Battery Size
Rating Required Number* Backbox Part Number†
18 AH 12 volts two BAT-12180 NFS-320 enclosure, BB-25
26 AH 12 volts two BAT-12260 NFS-320 enclosure, BB-25
100 AH 12 volts four for 100 AH BAT-121000 BB-100
two for 200 AH BB-200
*Manufactured to our specifications.
†Red version available; add “R” to part number listed here
Table A.5 Selecting Battery and Battery Backbox

Appendix B: Electrical Specifications
B.1 Electrical Specifications

AC Power
Component Values
Main Power Supply 120 VAC, 50/60 Hz, 5.0 A; or

240 VAC, 50/60 Hz, 2.5 A
Wire size Maximum 12 AWG (3.31 mm2) with 600 VAC insulation
NOTE: If using an auxiliary power supply such as FCPS-24S6/S8 or APS-6R, refer to the
documentation for that equipment.
Batteries
The control panel uses only sealed lead-acid batteries for secondary standby power. Maximum
battery capacity for the KAPS-24/E main power supply is 200 AH. The NFS-320 enclosure
provides space for two 18 AH batteries. Use external battery boxes if the installation requires
larger capacity batteries; see Table A.5, “Selecting Battery and Battery Backbox,” on page 51.
The table below contains battery charger specifications.
Charger Description Specifications
KAPS-24/E An internal battery charger Normal Charge: 27.6 VDC +/- 0.24 VDC
Main Power Supply for 18 AH to 200 AH Charging Current: 2.0 A or 5.7 A (Software selectable)
CHG-120 An external battery charger Dual Rate: High Charge: 28.1 VDC
Battery Charger designed to charge lead-acid Normal Charge: 27.6 VDC
batteries between 26 AH and Charging Current: 4.5 A
120 AH
ACPS-2406 An internal battery charger Normal Charge: 27.6 VDC
Auxiliary for 7AH to 26 AH Charging Current: 1.1 A max (0.750 A typical)
Charger/Power
Supply
Signaling Line Circuit (SLC)

Item Value
Voltage 24 VDC nominal, 27.6 VDC maximum
Maximum length 12,500 ft. (3810 m) per channel (NFPA Style 4) or 10,000 ft. (3048 m) total
loop or circuit length (NFPA Style 6 and 7)
Note: Refer to Appendix B.2 “Wire Requirements” for limitations.
Maximum current 400 mA peak, (max short circuit; circuit will shut down until short is fixed)
Maximum resistance 50 ohms (supervised and power-limited)

Electrical Specifications Electrical Specifications
Notification Appliance Circuits and Releasing Circuits

Item Value
Max. wiring voltage drop 2 VDC
(Retrofit note: SLCs with old CMX modules are restricted to 1.2 VDC.)
NAC Nominal operating 24 VDC regulated; 1.5 A max.
voltage
Special Applications for 20.16 - 26.42 VDC
Releasing Circuits
Current for all external 7.4 A in alarm (3.9 A continuous)
devices connected to the
control panel’s power supply
Optional ACPS-2406 Total 6 A in alarm (5 A continuous)
Optional APS-6R Total 6 A in alarm (4 A continuous)
Maximum signaling 1.5 A
current/circuit per NAC Note: Some devices have maximum draws less than this; refer to the device’s
documentation.
End-of-Line Resistors Control Panel NACs (TB6, TB7, TB8, TB9): 2.2K, 1/2 watt
(ELRs) XP6-C, FCM-1 Modules: 47K, 1/2 watt
NOTE: For a list of compatible Notification Appliance Circuits and Releasing Circuits see Notifier Device
Compatibility Document 15378.
Output Relays (common)

Output relays for Alarm and Trouble are common on TB4; Supervisory, and Security are
programmable on TB5. See Figure 3.9, “Form-C Relay Connections” on page 26).
Contact ratings: 2.0 A @ 30 VDC (resistive)
Four-wire Smoke Detector Power
Control Panel terminals TB10 RESET (+) and (–) supply filtered, low-noise power for four-wire
smoke detectors. Specifications are:
• Nominal voltage: 24 VDC special applications.
• Maximum rated current: 1.25 A DC
• Maximum ripple voltage: 176 mVrms
Refer to the Device Compatibility Document for compatible 24 VDC detectors.
Power Output
Control Panel terminals TB10 NONRESET (+) and (–) supply one (1) power-limited circuit
available to power external devices, such as notification appliances and annunciators.
• Nominal voltage: 24 VDC regulated, special applications, 1.5 A max.
• Maximum rated current: 1.25 A DC
• Maximum ripple voltage: 176 mVrms
Refer to the Device Compatibility Document for compatible devices and notification appliances.
NOTE: The Control Panel provides a total of 7.4 A of power in alarm (3.9 A in standby), shared
by all internal circuitry and external provisions (24 V resettable and non-resettable). For power
requirements, refer to the power supply calculation tables in Appendix A.
Operating Power: AC Branch Circuit

The control panel requires connection to a separate dedicated AC branch circuit. Follow these
guidelines when connecting the AC branch circuit:
• Label the branch circuit “Fire Alarm”. This must be a separate dedicated AC fire alarm circuit.
• Connect the branch circuit to the line side of the main power feed of the protected premises.

Electrical Specifications Wire Requirements
• Do not power other equipment from the fire alarm branch circuit.
• Run the AC branch circuit wire continuously, without any disconnect devices except for
overcurrent protection, from the power source to the fire alarm control panel.
• Overcurrent protection for the AC branch circuit must comply with Article 760 of the National
Electrical Codes, as well as local codes.
• Use 12 AWG (3.31 mm2) wire with 600 VAC insulation for the AC branch circuit.
Connect the ground terminal (TB1-Earth) to a solid earth ground (a metallic, cold water pipe may
be suitable in some installations). This connection is vital to maintaining the control panel’s
immunity to unwanted transients generated by lightning and electrostatic discharge.
Operating Power: Secondary Power Source (Batteries)
The battery charger is current-limited and can recharge sealed lead-acid type batteries. The battery
charger shuts off when the control panel is in alarm.
B.2 Wire Requirements

Each type of circuit within the Fire Alarm Control System requires use of a specific wire type to
ensure proper circuit operation. The wire gauge of a particular circuit depends on the length of that
circuit and the current traveling through it. Use Table B.1 below to determine the specific wiring
requirements for each circuit.
Compliance with the Federal Communications Commission (FCC) and Canadian Department of
Communication regulations on electrical energy radiation requires the following: Use twisted-pair
shielded wire for any non-SLC-loop wiring entering or exiting the cabinet that is not enclosed in
conduit. Use twisted-pair unshielded wiring for SLC-loop wiring.
NOTE: If running an SLC in conduit with Notification Appliance Circuits, you can reduce
problems by exclusively using electronic sounders (such as the SpectrAlert, SpectrAlert Advanced
or MA/SS-24 Series) instead of more electronically noisy notification appliances (such as
electromechanical bells or horns).

Wire Requirements Electrical Specifications
Circuit Distance
Circuit Type
Function
Wire Requirements
(feet/meters) Typical Wire Type*
SLC Connects to Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm2)
(power limited) intelligent and (3.31 to 0.82 mm2). 50 ohms maximum per 9,500 ft. (2,895.6 m) 14 AWG (2.08 mm2)
addressable length of Style 6 and 7 loops. 50 ohms per 6,000 ft. (1,828.8 m) 16 AWG (1.31 mm2)
modules. branch maximum for Style 4 loop. 3,700 ft. (1,127.76 m) 18 AWG (0.82 mm2)
or Untwisted, unshielded wire, in conduit or 1,000 ft. (304.8 m) 12 to 18 AWG (3.31 to
outside of conduit. 0.82 mm2)
Note: Maximum total capacitance of all

SLC wiring (both between conductors and
from any conductor to ground) should not
exceed 0.5 mircofarads.
EIA-485 Connects to Twisted-shielded pair with a characteristic 6,000/1829 16 AWG (1.31 mm2)
(power limited) FDU-80, ACS impedance of 120 ohms. 18 AWG (0.82 (max)
modules, or mm2) minimum.
TM-4
Transmitter
EIA-232 Connects to Twisted-shielded pair in conduit. 20 feet (6.1 m) 16 AWG (1.31 mm2)
(power limited) Printers, CRT, 18 AWG (0.82 mm2) minimum. (without modem)
or PC.
IDC FMM-1, 12-18 AWG (3.31 to 0.82 mm2). 12 to 18 AWG (3.31 to
Initiating Device FMM-101, Maximum circuit resistance is 20 ohms. 0.82 mm2)
Circuit FDM-1,
XP10-M,
XP6-MA
(power limited)
NAC FCM-1*, XP6-C 12-18 AWG (3.31 to 0.82 mm2). To meet 1.2 V drop, 12 to 18 AWG (3.31 to
Notification (power limited) At alarm current level, no more than a 1.2 or sized to provide 0.82 mm2)
Appliance V drop at the end of the circuit, or sized to the minimum rated
Circuit provide the minimum rated operating operating voltage of
voltage of the appliances used. the appliances used.
24 VDC Power To TM-4 12-18 AWG (3.31 to 0.82 mm2). To meet 1.2 volt drop 12 to 18 AWG (3.31 to
Runs Transmitter, Size wire so that no more than 1.2 V drop 0.82 mm2)
(power-limited) Annunciator and across wire run from supply source to end
FCM-1 modules of any branch.
CHG-120 External battery 12 AWG (3.31 mm2) in conduit 20/6.1 (max) 12 AWG (3.31 mm2)
charger
*FCM-1 can not be used for synchronized strobe/sounder applications.
Table B.1 Wire Requirements
* Notifier brand cable is recommended; see the product catalog available from Paige Electric.
NOTE: Lightning arresters required on circuits extending between buildings; 999 meter length
maximum to meet UL 60950.

Electrical Specifications Wire Requirements

Index
Numerics EOLR-1 See power supervision relay
24 VDC, see Power (DC)
F
A FCM-1 42
Fire/Security Applications 36–38
A77-716B
FMM-1 38
Replaced by EOLR-1
See power supervision relay Form-C relays 26, 53
AC, see Power 23, 24 Four-wire Smoke Detector
Specifications 53
Acceptance Test 44
ACM-8R
labeling requirements 28 I
Agent Release-Abort Station 43 Installation
Alarm relays, see Form-C relays 26 Checklist 19
Preparation 18
B
Backup-alarm switches 26 J
Batteries Jumper locations 13, 14
Battery calculations 46, 48, 49, 50, 51
Battery Checks and Maintenance 45
Battery specifications 52
K
Connections 24 KAPS-24/E, see Power supply
see also Power: DC 24
L
C LDM-R32
Cabinets 15 non-power-limited circuits 28
Mounting 20 LED locations 14
central receiving unit lockout 44
see also UDACT manual 37
Circuit Board, see CPU M
Compatible Equipment 16 Main power supply, see Power supply
compatible equipment 16, 17 Maintenance 44
Components 13, 14 microcontroller failure 26
Control Panel Circuit Board, see CPU Multiple Detector Operation 32
CPU
CPU-320 (120V operation) 11
CPU-320E (240V operation) 11 N
drawing 11, 13, 14 NACs (Notification Appliance Circuits)
Overview 11 Backup option 26
CRTs 31 NAC Connections 25
CRT/PRN combination 31 Releasing applications 25, 26, 39, 40
CRT-2 Configuration 30 Specifications 53
CRT-2 Function Keys and parameters 31 NBG-12LRA 43
Installation 28–32 Networking 22
NFPA Applications
NFPA 72 Central or Remote Station Fire
D Alarm System 34
DC, see Power 23, 24 NFPA Applications (Overview) 34
Nonpower-limited circuits
E UL wiring requirements 27, 28
Electrical connections 22 Notification Appliance Circuits, see NACs
Electrical Specifications 52

O–W Index
O Supplemental Documentation 8
Switches
Operating Power 53, 54
Backup-alarm 26
Operational Checks 44
switch locations 13, 14
Option boards
Installation steps 20 System
Description of features 10
Output relays
Connections 26, 53 Limitations 11
Options 11
Specifications 53
System current draws 46, 48, 49, 50, 51
P
T
Periodic Testing 44
Power Terminal block locations 13, 14
AC Power Checklist 23 Testing 44
TM-4
AC power connections 23, 24
see TM-4 Transmitter Module Installation
AC specifications 52
Document 21
DC power connections 23, 24
Trouble relays, see Form-C relays 26
Installation steps 22
Power specifications 22, 53
power supervision relay 42, 43 U
power supply 12 UL nonpower-limited wiring requirements 27
Power supply calculations 46, 48, 49, 50, 51 UL Requirements 27
Power-limited Wiring Requirements 27
Printers 31
Installation 28–32
V
PRN series connections 29 VeriFire 33
PRN settings 29
PRN/CRT combination 31 W
Proprietary Security Alarm Applications Wiring
Wiring 38 Proprietary Security Alarm Applications
Protected Premises Unit 34 38
Wire Requirements 54
R
Related Documentation 8
Relays, see Form-C relays 26
Releasing Circuits
Connections 25
Releasing Applications 39–43
Specifications 53
Releasing Device
Connections 40
FCM-1 Connections 42
S
Security relays, see Form-C relays 26
Security Tamper Switch 37, 38
Service 44
SLC
see also SLC Wiring Manual 32
specifications 52
Specifications 52, 53
Standard equipment 11
STS-1, see also Security Tamper Switch 38
Supervisory and Security contacts
configuring as Alarm contacts 26
Supervisory relays, see Form-C relays 26

Limited Warranty
NOTIFIER® warrants products manufactured by it to be free from

defects in materials and workmanship for eighteen (18) months from
the date of manufacture, under normal use and service. Products are
date stamped at time of manufacture. The sole and exclusive
obligation of NOTIFIER® is to repair or replace, at its option, free of
charge for parts and labor, any part that is defective in materials or
workmanship under normal use and service. All returns for credit are
subject to inspection and testing at the factory before actual
determination is made to allow credit. NOTIFIER® does not warrant
products not manufactured by it, but assigns to the purchaser any
warranty extended by the manufacturer of such products. This
warranty is void if the product is altered or repaired by anyone other
than NOTIFIER® or as expressly authorized by NOTIFIER® in
writing, or is serviced by anyone other than NOTIFIER® or its
authorized distributors. This warranty is also void if there is a failure to
maintain the products and systems in which they operate in a proper
and workable manner. In case of defect, secure a Return Material
Authorization form from our Return Authorization Department.
This writing constitutes the only warranty made by NOTIFIER®, with
respect to its products. NOTIFIER®, does not represent that its
products will prevent any loss by fire or otherwise, or that its products
will in all cases provide the protection for which they are installed or
intended. Buyer acknowledges that NOTIFIER®, is not an insurer
and assumes no risk for loss or damages or the cost of any
inconvenience, transportation damage, misuse, abuse, accident or
similar incident.
NOTIFIER® GIVES NO WARRANTY, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
OR OTHERWISE WHICH EXTENDS BEYOND THE DESCRIPTION
ON THE FACE HEREOF. UNDER NO CIRCUMSTANCES SHALL
NOTIFIER® BE LIABLE FOR ANY LOSS OF OR DAMAGE TO
PROPERTY, DIRECT, INCIDENTAL OR CONSEQUENTIAL,
ARISING OUT OF THE USE OF, OR INABILITY TO USE
NOTIFIER®’S PRODUCTS. FURTHERMORE, NOTIFIER® SHALL
NOT BE LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH
MAY ARISE IN THE COURSE OF, OR AS A RESULT OF,
PERSONAL, COMMERCIAL OR INDUSTRIAL USE OF ITS
PRODUCTS.
This warranty replaces all previous warranties and is the only
warranty made by NOTIFIER®. No increase or alteration, written or
verbal, of the obligation of this warranty is authorized.
"NOTIFIER" is a registered trademark.
Warn-NL-04-2005.fm

World Headquarters
12 Clintonville Road
Northford, CT 06472-1653 USA
203-484-7161
fax 203-484-7118
www.notifier.com

NFS-320 Installation Manual

Uploaded by

Copyright:

Available Formats

NFS-320 Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NFS-320 Installation Manual

Uploaded by

Copyright:

Available Formats

Fire Alarm Control Panel

2 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 3

4 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 5

Section 4: Applications .......................................................................................................... 34

6 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

1.1 Standards and Other Documents

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 7

1.2 UL 864 Compliance

1.3 Related Documents

Compatible Conventional Devices (Non-addressable) Document Number

Device Compatibility Document 15378

NFS-320/E/C Installation, Operations, and Programming Manuals 52745, 52746, 52747

SLC Wiring Manual 51253

Off-line Programming Utility Document Number

VeriFire™ Tools CD help file VERIFIRE-TCD

ACPS-2406 Installation Manual 51304

APS-6R Instruction Manual 50702

CHG-120 Battery Charger Manual 50641

FCPS-24S6/FCPS-24S8 Field Charger/Power Supply Manual 51977

Networking Document Number

Noti•Fire•Net Manual, Network Version 4.0 & Higher 51584

NCM-W/F Installation Document 51533

NCA-2 Network Control Annunciator Manual 52482

Table 1.1 Reference Documentation (1 of 2)

8 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

NCA Network Control Annunciator Manual 51482

System Components Document Number

Annunciator Control System Manual 15842

Annunciator Fixed Module Manual 15048

AFM-16A Annunciator Fixed Module Manual 15207

ACM-8R Annunciator Control Module Manual 15342

FDU-80 Remote Annunciator Manual 51264

LDM Series Lamp Driver Annunciator Manual 15885

DPI-232 Direct Panel Interface Manual 51499

TM-4 Installation Document (Reverse Polarity Transmitter) 51490

UDACT Manual (Universal Digital Alarm Communicator/Transmitter) 50050

FireVoice-25/50 & FireVoice-25/50ZS Manual 52290

RA400Z Remote LED Annunciator Installation Document I56-508

Table 1.1 Reference Documentation (2 of 2)

1.4 Cautions and Warnings

1.4.1 Typographic Conventions

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 9

2.1 System Description

2.1.1 Standard Features

10 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

2.1.3 System Limitations

2.2 System Components

2.2.2 Control Panel Circuit Board

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007 11

2.2.3 Main Power Supply KAPS-24/E

12 NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

J2 - USB A VeriFire Tools Connection

TB3 - Battery Connection

NFS-320/E/C Installation Manual — P/N 52745:A 01/12/2007

TB7 - NAC#3 12057

TB1 - AC Power Connection

Figure 2.2 CPU-320 and Power-Supply: Wiring Connections

Output Relays - power-limited only if connected to a power-limited