MPD Falcon PDF

FALCON 900EX EASY
SCHEDULED MAINTENANCE
0900400080496827 - VALIDATED - Certification Repository
Effectivity: ALL
Rev. Date: MAR 15/2011
00-00-00
page 1 / 1
"DASSAULT AVIATION Proprietary Data"
FALCON 900EX EASY
05-00-03
LIST OF REVISIONS
CHAPTER 5
REVISION No. DATE OF ISSUE
ORIGINAL EDITION MARCH 2011
Effectivity: ALL
05-00-03
page 1 / 1
FALCON 900EX EASY
05-00-05
INFORMATION TO OPERATORS
1. INFORMATION TO OPERATORS
You will find herewith the Original Issue dated March 2011 of the Chapter 5 DGT 125289.
This manual supersedes the Chapter 5 Extended (DGT 440) Revision 2 dated March 2010 and the Chapter
5 Non Extended (DGT 620) Revision 11 dated July 2010.
The Original Issue of this manual is based on the ATA AMTOSS specification implemented in the AMM for
maintenance task numbering.
In order to assist operators with this new standardized numbering convention, both the old numbering and the
new AMTOSS numbering are indicated in the column "Scheduled maintenance task number" as follow:
A. Section 05-10
Scheduled maintenance task number example
24-30-00-710-801 AMTOSS numbering

24-304 Old MP numbering
B. Section 05-20
Scheduled maintenance task number examples
21-32-06-200-801-01 AMTOSS numbering

21-314 [213141] Old MP numbering [Old operation code]

[212041] Old MP not available [Old operation code]

[321052, 321054] Old MP not available [2 old operation codes merged in a single AMTOSS
operation code]
27-53-01-350-802-01 AMTOSS numbering of new task

[] Old MP not available [Old operation code not available]
2. CROSS PROCEDURE REFERENCE TABLE

In addition, a cross procedure reference table is available in the FIELD collection (manual GENERAL) and a
(.xls) file is posted on the Falcon portal through [Reference - Center / FIELD / FIELD 5 / How-To].
3. MAIN MODIFICATIONS
The main modifications of the sections 05-10 and 05-20 done in the Original Version of this MPD Chapter 5
compared to the F900EXEASy/F900DX WITH SB F900EX-333 or S/N 195 to 600 or S/N > 618 Chapter 5
(DGT 440) Revision 2 (March 2010) with TR 7, 8 and 9 are listed hereafter:
A. All sections:
• Better RVSM tasks identification.
Effectivity: ALL
05-00-05
page 1 / 2
FALCON 900EX EASY
B. Section 05-10
• Creating the new Z inspection in order to cancel enrolment prerequisites to move to the extended
maintenance schedule (Refer to Chapter 05-10-00, Paragraph “Maintenance Cycle”).
As a consequence, this new manual is applicable to all aircraft compliant or not with the SB
F900EX-333. The Z inspection must be reckoned from the date of the last 4A+ inspection (Chapter 5
DGT ) or the date of the last 3A+ inspection (Chapter 5 DGT ).
C. Section 05-20
• Operation “RESTORATION OF THE STARTER GENERATORS (OVERHAUL). Effectivity changed
to add P/N 8060-140, 8060-140-1, 8060-141 and 8060-141-1.
• Operation “CHECK/REPLACEMENT OF STARTER-GENERATOR BRUSHES” created for P/N
8060-140, 8060-140-1, 8060-141 and 8060-141-1.
• Operation “DISCARD OF THE FLAP SCREW JACKS – LH/RH OUTBOARD FLAP SCREW JACK”.
Effectivity P/N 1-5319-3 or 2-5319-3. Interval changed from “15,000 LDG or 24 Y” to “16,000 LDG”.
• Operation “DISCARD OF THE FLAP SCREW JACKS – LH/RH INBOARD FLAP LATERAL/CENTER
SCREW JACK“. Effectivity P/N 5318-3. Interval changed from “15,000 LDG or 24 Y” to “15,000 LDG”.
• Operation “FUNCTIONAL TEST OF THE BP MANIFOLD THERMAL EXPANSION SYSTEMS - BP 2
MANIFOLD (M32WB)”. Effectivity changed to add P/N L88A31-695.
• Operation "CALIBRATION OF THE RADIO ALTIMETER RECEIVER / TRANSMITTER – RADIO
ALTIMETER 2 RECEIVER/TRANSMITTER (22SA)". Operation code created with a “2 Y” interval for
Radio-altimeter 2 receiver/transmitter (22SA). Effectivity only for CAT II and CAT III operation and with
P/N 7001840-932.
• Operation “LEAK TEST OF PILOT / COPILOT / STAND-BY AIR PRESSURE SYSTEM": NO LONGER
SCHEDULED. Operation already included in “Functional test of the air data indicator”.
Effectivity: ALL
DD 1-169876476 Rev. Date: MAR 15/2011
05-00-05
page 2 / 2
FALCON 900EX EASY
CONTENTS
TABLE OF CONTENTS
00-00: MAINTENANCE PLANNING DOCUMENT
00-00-00: MAINTENANCE PLANNING DOCUMENT

MAR 15/2011 ALL
05-00: GENERAL
05-00-00: GENERAL
MAR 15/2011 ALL
05-00-03: LIST OF REVISIONS

MAR 15/2011 ALL
05-00-05: INFORMATION TO OPERATORS

MAR 15/2011 ALL
05-00-10: TABLE OF MODIFICATIONS

MAR 15/2011 ALL
05-10: AIRCRAFT MAINTENANCE OPERATIONS
05-10-00: AIRCRAFT MAINTENANCE OPERATIONS

MAR 15/2011 ALL
05-10 CHAPTER 05 : TIME LIMITS / MAINTENANCE CHECKS
MAR 15/2011 ALL
05-10 CHAPTER 21 : AIR CONDITIONING

MAR 15/2011 ALL
05-10 CHAPTER 22 : AUTO FLIGHT

MAR 15/2011 ALL
05-10 CHAPTER 23 : COMMUNICATIONS

MAR 15/2011 ALL
05-10 CHAPTER 24 : ELECTRICAL POWER

MAR 15/2011 ALL
05-10 CHAPTER 25 : EQUIPMENT / FURNISHINGS

MAR 15/2011 ALL
05-10 CHAPTER 26 : FIRE PROTECTION

MAR 15/2011 ALL
Effectivity: ALL
CONTENTS
page 1 / 5
FALCON 900EX EASY
CONTENTS
05-10 CHAPTER 27 : FLIGHT CONTROLS

MAR 15/2011 ALL
05-10 CHAPTER 28 : FUEL

MAR 15/2011 ALL
05-10 CHAPTER 29 : HYDRAULIC POWER

MAR 15/2011 ALL
05-10 CHAPTER 30 : ICE AND RAIN PROTECTION

MAR 15/2011 ALL
05-10 CHAPTER 31 : INDICATING - RECORDING SYSTEMS

MAR 15/2011 ALL
05-10 CHAPTER 32 : LANDING GEAR

MAR 15/2011 ALL
05-10 CHAPTER 34 : NAVIGATION

MAR 15/2011 ALL
05-10 CHAPTER 35 : OXYGEN

MAR 15/2011 ALL
05-10 CHAPTER 36 : PNEUMATIC

MAR 15/2011 ALL
05-10 CHAPTER 38 : WATER - WASTE

MAR 15/2011 ALL
05-10 CHAPTER 45 : CENTRAL MAINTENANCE SYSTEM (CMS)

MAR 15/2011 ALL
05-10 CHAPTER 52 : DOORS

MAR 15/2011 ALL
05-10 CHAPTER 53 : FUSELAGE

MAR 15/2011 ALL
05-10 CHAPTER 54 : NACELLES AND PYLONS

MAR 15/2011 ALL
05-10 CHAPTER 55 : STABILIZERS

MAR 15/2011 ALL
Effectivity: ALL
CONTENTS
page 2 / 5
FALCON 900EX EASY
CONTENTS
05-10 CHAPTER 56 : WINDOWS

MAR 15/2011 ALL
05-10 CHAPTER 57 : WINGS

MAR 15/201 ALL
05-10 CHAPTER 71 : POWER PLANT

MAR 15/2011 ALL
05-10 CHAPTER 73 : ENGINE FUEL AND CONTROL

MAR 15/2011 ALL
05-10 CHAPTER 76 : ENGINE CONTROLS

MAR 15/2011 ALL
05-10 CHAPTER 77 : ENGINE INDICATING

MAR 15/2011 ALL
05-10 CHAPTER 78 : EXHAUST

MAR 15/2011 ALL
05-20: COMPONENT MAINTENANCE OPERATIONS
05-20-00: MAINTENANCE OF COMPONENTS, TIME BETWEEN

OVERHAULS AND LIFE LIMIT
MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL
Effectivity: ALL
CONTENTS
page 3 / 5
FALCON 900EX EASY
CONTENTS

MAR 15/2011 ALL

MAR 15/2011 ALL
MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL
05-20 CHAPTER 33 : LIGHTING

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL

MAR 15/2011 ALL
Effectivity: ALL
CONTENTS
page 4 / 5

FALCON 900EX EASY
CONTENTS
05-40: AIRWORTHINESS LIMITATIONS
05-40-00: AIRWORTHINESS LIMITATIONS (See Reference DGT 113875)
05-50: UNSCHEDULED MAINTENANCE CHECKS
05-50-00: UNSCHEDULED MAINTENANCE CHECKS

MAR 15/2011 ALL
Effectivity: ALL
CONTENTS
page 5 / 5
FALCON 900EX EASY
05-00-00
GENERAL
1. FOREWORD
This manual is the maintenance manual chapter 5 of the FALCON 900EX EASy including A/C with M5281
(winglet).
The sections 05-00, 05-10, 05-20 and 05-50 of this manual define maintenance operations and frequencies
recommended by DASSAULT AVIATION to maintain the aircraft's airworthiness and to prevent degradation
of maintenance standards directly related to reliability. In addition, this schedule is intended to maintain these
standards at a minimum cost. The technical content of these sections is approved under the authority of DOA
nr.EASA.21J.051. Only the most recent revision of the present document corresponds to the
recommendations of the manufacturer DASSAULT AVIATION. The manual forms an entity, and the operations
described in one of the sections take into account the correct accomplishment of all operations contained in
the other sections. Consequently, only the whole document incorporating this most recent revision is approved
and it supersedes all previous revisions or reissues.
In addition, this Manual is completed by the "Airworthiness Limitations Section" 5-40 (DGT 113875). These
Airworthiness Limitations are limitations established for airframe, systems and items of equipment. This
section 5-40 is approved by the EASA (European Aviation Safety Agency). Mandatory operations on the
structure or systems in section 5-40 are also listed in section 5-10 and 5-20. These operations cannot be
deleted from the maintenance program. Their frequencies can be modified only with the agreement of the
manufacturer and the approval of the Certification Authorities without exceeding frequencies given in section
5-40.
2. APPLICABILITY
This maintenance program is valid for FALCON 900EX EASy delivered by DASSAULT AVIATION. This
manual refers only to installations designed or approved by the airplane manufacturer and incorporated in the
aircraft type design. It is recommended to use the spares, tools and special equipment listed in this
Maintenance Manual and Tools and Equipment Manual, unless alternate tools are developed and acceptable
to the local authority.
Other changes such as STCs, P.M.A. (Parts Manufacturer Approval) are not included in this manual.
Consequently, the operators shall add, modify, replace or delete operations required for maintenance of
different or supplementary installations to the maintenance program recommended by DASSAULT AVIATION.
The "standard" Chapter 5 maintenance program may not apply to the aircraft that are involved in accidents
and/or incidents which result in structural damage or other major or unusual damage to the aircraft.
Falcon aircraft involved in such accident or incident will require the review and/or the inspection of all structure/
equipment that has sustained significant or unusual damage associated with the accident/incident. Only the
manufacturer or its authorized representative can determine if the recommended maintenance program is still
applicable to such aircraft. Should this review/inspection reveal that the standard chapter 5 maintenance
program is not suitable, based upon the facts involved, subject aircraft maintenance program may have to be
supplemented by additional inspection criteria.
This maintenance program is applicable to aircraft on a fleet-wide basis regardless of the regulations of the
country in which the aircraft is registered. It includes the maintenance inspections required for operation in
the RVSM airspace.
However, the operator shall comply with the specific requirements as prescribed by the Authority of his country
of registration, e.g:
- EASA Part M (unless National Authority regulations are applicable),
Effectivity: ALL
05-00-00
page 1 / 6
FALCON 900EX EASY
- FAA regulations applicable to the USA and certain countries in the Western Hemisphere, particularly FAR
Parts 91 and 135,
- regulations established by the representative authorities of other countries.
This manual is based on a standard flight defined as follows:
- one take-off, one climb, one descent and one landing.
If the aircraft operation is different than the above description, or specific, the maintenance program must be
modified (refer to paragraph 5. - Structural Maintenance).
With approval of the relevant authorities of the country in which the aircraft is registered, the operator
of the aircraft may adapt the maintenance program recommended by the manufacturer. The operator
is held responsible for these changes.
These changes enable to adapt the maintenance program:
- in relation to the aircraft grounding possibility for the maintenance and desired operational availability,
- in relation with the aircraft operation (flying hours per year, environmental conditions, etc.).
3. MANUAL BREAKDOWN
The manual consists of 3 sections:
A. Section 5-10: Aircraft Maintenance Operations

This section lists all scheduled maintenance operations to be performed on the aircraft with their time
frequencies. It does not include maintenance operations performed in the workshop on items of
equipment, removed from the aircraft, which are addressed in section 5-20.
B. Section 5-20: Component maintenance operations

This section lists all scheduled maintenance operations for items of equipment and provides their time
frequencies.
C. Section 5-50: Unscheduled Maintenance Checks

This section lists all maintenance operations (Inspection/Check or Test) justified by a particular type of
aircraft operation, or unscheduled maintenance operations associated with aircraft safety.
NOTE: The " Airworthiness Limitations Section" 5-40 is provided as a separate document DGT 113875.
4. ENGINE AND APU INSPECTIONS

- For engine inspection, see engine manufacturer's Maintenance Documentation.
- It is essential to record engine cycles in order to comply with the time limits of the internal components of
the TFE 731-60 engine. These limitations are given in the Engine manufacturer's technical publications.
HONEYWELL-ALLIED SIGNAL REPORT 72-03-06 for MODEL TFE 731-60.
- For APU, see manufacturer's maintenance documentation for inspection and life limited parts.
HONEYWELL-ALLIED SIGNAL REPORT 49-24-02 for MODEL GTCP 36-150[F].
5. STRUCTURAL MAINTENANCE
Airworthiness is achieved by taking all the necessary steps to prevent damage occurring during use and likely
to affect the safe operation of the aircraft.
The FALCON 900EX EASy satisfies the "DAMAGE TOLERANCE" JAR 25.571 change 13 - structural design
conditions.
Effectivity: ALL
05-00-00
page 2 / 6
FALCON 900EX EASY
Fatigue damage simulation tests corresponding to 20,000 flight cycles have been performed by mathematical
modelling and confirmed by 40,000 fatigue cycles followed by 20,000 damage tolerance cycles, i.e. a total of
60,000 fatigue test cycles on an airframe representative of the complete aircraft.
A maintenance program is associated with these tests and updated regularly by the manufacturer. It is based
on periodic operations to be performed systematically, described in the various chapters and whose
frequencies are derived directly from the results of mathematical modelling and the results of fatigue tests or
damage tolerance calculations. It is on this basis that the manufacturer's stress department fixed the frequency
of the C inspection at 3750 flight cycles.
The "SAFE LIFE" components, the life limits of which have been demonstrated during the fatigue tests, are
listed in section 5-40. The limits for mandatory structural inspections resulting from the tests and damage
tolerance calculations are incorporated in the section 5-40 in accordance with appendix H of JAR 25.
NOTE: Servicing interval, TBO and service life are determined as follows:
• in Flying Hours (FH) for structural components, for which stress accumulation is function of flight
duration,
• in Landings (LDG) for structural components where maximum stress is encountered during landing/
take-off. The number of Landings is the number of flights plus the number of touch-and-go,
• in Flight Cycles (FC) for structural components mainly affected by cabin pressurization. The number
of Flight Cycles is the number of flights plus the number of additional pressurization cycles above
1 psi.
6. MAINTENANCE MANUALS TO BE CONSULTED

- Aircraft MAINTENANCE MANUAL.
- Engine Light Maintenance Manual for MODEL TFE 731-60.
- APU Maintenance Manual for MODEL GTCP 36-150[F].
- Supplemental MM and Chapter 5 issued by the completion center.
NOTE: Options installed during initial completion may be also covered by the basic AMM and/or Chapter 5.
In that case, refer to the most recent publication.
7. COMMUNICATION AND NAVIGATION SYSTEMS
A. In all cases the scheduling of maintenance procedures applicable to communication and navigation
systems shall not provide intervals exceeding those advised by manufacturers. The recommended
schedule is provided in Chapter 5 section 5-10 and 5-20, ATA 22, 23, 24 and 34.
Some operational regulations (Public Transportation, precision approaches categories I, II, III, etc.) may
influence the scheduling of maintenance in relation to aircraft flight operation (e.g. number of successful
CAT II approach landings). It is therefore required to check for compliance of manufacturer's
recommended schedule in view of aircraft flight activities.
The regulations and notes concerning the operation and maintenance of aircraft for Public Transport,
and aircraft operated in CAT I and CAT II are:
• aircraft registered in France: "Arrêté" dated May 12, 1997 and JAR AWO (All Weather Operations),
• aircraft registered in the United States under FAR 121, FAR 135: Advisory Circular No. 120-29,
• aircraft registered in another country: following requirements of local authorities.
Maintenance of these systems is performed in the following manner.
(1) Functional tests scheduled in section 5-10 to be performed on the aircraft and designed to validate
all the components comprising a system.
Effectivity: ALL
05-00-00
page 3 / 6
FALCON 900EX EASY
These tests are generally performed using tests integrated in the main components within the
system.
This maintenance philosophy is applicable to components of digital design. Integrated tests replace
bench tests of these components and thus avoid any possible damage to connectors.
(2) Bench test of components scheduled in section 5-20, to be performed in specialized workshops
approved by the airworthiness authorities (E.A.S.A., FAA, etc.).
These bench tests generally apply to analog components receiving electronic data or air pressure
from static or pitot pressure probes. Several components of this type can be calibrated on the aircraft
using a calibrated test bench. This test bench is designed to check that these components operate
within the required tolerances.
(3) During the first year of operation, each operator must supply the representatives of the local
authority in charge of airworthiness with a three-monthly report containing the following data:
(a) The number of real or simulated approaches employing category II equipment.
(b) The total number of unsatisfactory approaches and the technical reasons for these.
(c) The total number of instances of removal of components required for category II certification
(for failure or unsatisfactory operation).
NOTE: Operating report is to be submitted monthly for aircraft under FAA registration.
The list of data submitted in the operating report and the presentation of this data is to be
subject to negotiation between each operator and the local airworthiness authorities.
B. Operators using the aircraft for Private Transport (FAR 91) using category II must satisfy FAR 91
appendix A.
Maintenance of their navigation radio and automatic pilot equipment must be performed according to
sub-paragraphs (1) and (2) of paragraph A. above.
8. NOTES
NOTE 1:
Return to approved repair agent for maintenance action per instruction in AMM maintenance procedure.
NOTE 3:
It is recommended to replace both main batteries at the same time.
NOTE 4:
The battery has a maximum installed service life of 4 years and a combined service/storage life of 6 years.
While the battery is stored, perform a battery capacity check using the ENERGY LEVEL TEST switch at least
every 90 days.
NOTE 5:
The storage duration must not exceed 5 years.
NOTE 6:
For cartridges P/N 861375 and 861385: the cartridge has a maximum installed service life of 5 years and a
combined service/storage life of 7 years.
For cartridges P/N 862700-00 and 862710-00: the cartridge has a maximum installed service life of 10 years
and combined service/storage life of 12 years.
NOTE 8:
Overhaul required if test fails. After overhaul tube starts again as zero time.
NOTE 9:
Effectivity: ALL
05-00-00
page 4 / 6
FALCON 900EX EASY
Download interval depends on PCMCIA card capacity. The appropriate interval must be calculated as a
function of this parameter (Refer to table: fig. 1).
NOTE 10:
The time base is for factory installed landing gear:
- the delivery date to the customer, if the delivery date of aircraft to customer after completion by the Completion
Center or the manufacturer does not exceed 10 months after aircraft first flight,
- the date of the first flight plus 10 months, if the delivery date of aircraft to customer after completion by the
Completion Center or the manufacturer exceeds 10 months after aircraft first flight,
The time base for new or overhauled spare landing gear is: the date of first installation on the aircraft, except
if storage conditions have not been in accordance with the CMM. In that case the time base will be the overhaul
date.
This time base is also applicable to the subassemblies of the new Landing Gear installed on the A/C as well
as to a complete spare Landing Gear.
NOTE 11:
The TBO of main landing gear legs and of nose landing gear leg is extended to 12 years if the detailed
inspection of main landing gear legs (Refer to TASK 32-11-00-220-801) and of nose landing gear leg (Refer
to TASK 32-21-00-220-801) have been performed at 6 years.
NOTE 12:
The time base for passenger door pneumatic actuator life limit is the delivery date of A/C to the customer (new
or after an actuator change), or the manufacture date of the actuator plus 18 months whichever comes first.
NOTE 13:
Limited storage time: 18 months maximum.
Effectivity: ALL
05-00-00
page 5 / 6
FALCON 900EX EASY
Figure 1: Note 9 QAR download scheduling
Effectivity: ALL
05-00-00
page 6 / 6
FALCON 900EX EASY
05-00-10
TABLE OF MODIFICATIONS
1. TABLE OF MODIFICATIONS LISTED IN CHAPTER 5
ATA MODIF. DESCRIPTION SB NOTES
24 M3420 Installation of batteries charging by SB 150 Option

GPU
30 M3580 Brake heating system SB 230 Option
30 M5505 Brake heating system
32 M5028 Nose landing gear shield door - adding SB 265

safety stop
57 M5281 Winglet installation
73 M5288 Improved fuel filter bypass indication SB 311 Option
Effectivity: ALL
05-00-10
page 1 / 1
FALCON 900EX EASY
05-10-00
AIRCRAFT MAINTENANCE OPERATIONS
1. GENERAL
This section lists, in accordance with the ATA 100 chapter breakdown system, all maintenance operations
which must be performed on aircraft systems and the airframe.
The zonal inspection/check procedures are itemized in "STRUCTURE" ATA chapters 53, 54, 55 and 57 and
include inspections of structure, aircraft systems and equipment located in these areas.
2. TERMINOLOGY
A. A, Z, B and C inspections.
B. Functional test/check.
Quantitative check to determine if one or more functions of an item performs within specified limits.
C. Operational test/check.
Task to determine if an item is fulfilling its intended purpose. The task does not require quantitative
tolerances.
D. Inspection/check
Visual or detailed inspection required to determine the condition of a system, an item of equipment or a
structure in relation to the design standard.
3. MAINTENANCE CYCLE
A. General
The maintenance cycle is based on 4 types of inspection:
• A inspection: every 400 flying hours (FH) or 8 months (M)
• Z inspection: every 2 years (Y)
• B inspection: every 1600 flying hours (FH)
• C inspection: every 3750 flight cycles (FC) or 6 years (Y)
Inspections may be performed with a shorter interval than recommended maintenance schedule. For
instance:
• a A inspection can be done at 6 months (M),
• a B inspection can be done at 1500 flying hours (FH).
B. A inspection
The A inspection must be performed at every 400 flying hours or 8 months, whichever limit is reached
first.
Effectivity: ALL
05-10-00
page 1 / 6
FALCON 900EX EASY
NOTE: To facilitate scheduling the A inspections, the manufacturer authorizes a tolerance of + 40 flying
hours for the flying hours + 1 month for the calendar limit. These tolerances are not cumulative.
The due time of any A inspection (or multiple) must never be exceeded by more than 40 flying
hours or 1 month. In addition, the period of time between two A inspections must not exceed
440 flying hours or 9 months.
The A, 2A, etc., inspections are basic maintenance inspections which mainly include the servicing
operations (greasing and lubrication, inspection/check) whose basic purpose is to ensure regular
verification of the aircraft condition regardless of its utilization rate.
Some operations are performed at multiples of the A inspection (identified as 2A, 4A, etc.).
They are complementary to the A inspection but are to be performed only at the times specified for a
multiple inspection. The 2A operations are therefore to be scheduled once every two A inspections, the
3A operations are to be scheduled once every three A inspections, the 4A operations are to be scheduled
once every four A inspections, etc.
Example: The fourth A inspection (1600 flying hours or 32 months) will include the A inspection
operations, plus the 2A operations, plus the 4A operations.
The operations complementary to A identified by the "+" symbol are calendar time operations.
Consequently, they should be performed every 8 months for a A+, 16 months for a 2A+, etc.
NOTE: It is possible to separate the A check from multiple of the A check (2A, 3A, 4A). However
tolerances, listed here after, between two same type of inspection have to be respected:
• A = 400 FH + 40 FH or 8 months + 1 month,
• 2A = 800 FH + 40 FH or 16 months + 1 month,
• 3A = 1200 FH + 40 FH or 24 months + 1 month,
• 4A = 1600 FH + 40 FH or 32 months + 1 month.
Effectivity: ALL
05-10-00
page 2 / 6
FALCON 900EX EASY
C. B inspection
• The B inspection must be performed at every 1600 flying hours.
NOTE: The manufacturer authorizes a tolerance of plus 40 flying hours maximum beyond the B
inspection due time (or multiple thereof). These tolerances are not cumulative (refer to the
following diagram). The due time of any B inspection (or multiple) must never be exceeded by
more than 40 flying hours. In addition, the period of time between two B inspections must never
exceed 1640 flying hours.
The purpose of the B inspection is to ensure operational and/or functional capabilities of systems whose
condition is mainly related to flying hours.
Some operations are performed at multiples of the B inspection (identified as 2B, 3B, etc.). They are
complementary to the B inspection but are to be performed only at the times specified for such operations.
Example: A 2B inspection will include B inspection operations and operations specific to the 2B
inspection.
D. Z inspection
The Z inspection must be performed at every 24 months.
This Z inspection is a complement to the A inspection. It is a basic maintenance inspection which mainly
includes zonal and specific RVSM operations.
NOTE: To facilitate scheduling the Z inspection, the manufacturer authorizes a tolerance of plus 1
month. This tolerance is not cumulative.
E. C inspection
Effectivity: ALL
05-10-00
page 3 / 6
FALCON 900EX EASY
The C inspection must be performed at every 3750 flight cycles or 6 years whichever limits is reached
first.
NOTE: The manufacturer authorizes a maximum tolerance of plus 2 months beyond the C inspection
calendar due time. No tolerance is allowed beyond the C inspection flights limit due time. The
interval between two C Inspections must be reckoned from the end of the C Inspection if the
duration of the inspection does not exceed 3 months. If the duration of the C Inspection exceeds
3 months, the interval must be reckoned 3 months after the beginning of the C Inspection.
NOTE: Cumuling tolerances on the C inspection is authorized. As 05-20-00 operations are independent
of the C operation, tolerances on C inspection cannot be applied to 05-20-00 operations.
The C inspection must be considered as a detailed inspection of the airframe and systems after opening
all doors and access panels.
The C inspection must also be considered as an inspection which, considering the extended down time
of the aircraft, allows reconditioning work to be done as well as the application of Service Bulletins which
are not already applied.
The C inspection must be supplemented by all the operations of the A inspection and multiples of A with
flying hours and calendar time limits (A, A+, 2A, 2A+, 3A, 4A, Z, etc.).
The C inspection must be supplemented by the B inspection operations if a B inspection has not been
performed since new or since the last C inspection.
However, the cycle of multiples of B inspection (2B, 3B, 4B) continues independently of the C inspection
cycle.
Some operations multiples of C (identified as 2C, 3C, etc.) are to be accomplished only at the time of
the multiple inspection.
A 2C inspection will include C inspection operations plus the operations specific to the 2C inspection.
Some inspections can be scheduled by number of flying hours (FH), those operations can be performed
during C checks.
4. DATE OF ORIGIN FOR THE CALENDAR INSPECTIONS

- If the date of origin for calendar inspections is listed in the aircraft log book, follow this date of origin.
- If not, the date of origin is the delivery date of the aircraft to the customer by DASSAULT AVIATION (the
date the Airworthiness Certificate is obtained), in the case of aircraft fully equipped by the manufacturer. For
aircraft delivered by DASSAULT AVIATION and equipped by a completion center, the date of origin for
calendar inspections must be reckoned from the delivery date to the customer by the completion center.
However, if the period of aircraft completion by the completion center exceeds 9 months, the date of the first
Effectivity: ALL
05-10-00
page 4 / 6
FALCON 900EX EASY
inspections may be reckoned from the date the stripped aircraft was delivered by DASSAULT AVIATION (the
date the Airworthiness Certificate is obtained) plus 9 months.
The date of calendar inspections (A or Z type) following a C inspection is reckoned from the date defined on
§ “Maintenance cycle – C inspection.
5. OPTIMIZED CONTINUOUS INSPECTION PROGRAM (O.C.I.P.)

Following the request of operators, DASSAULT AVIATION has developed an Optimized Continuous
Inspection Program, which is customized for each operator covering the A and Z, or A, Z and B inspections
and multiples.
These maintenance programs are an option available for operators who request it from the manufacturer. In
order to satisfy a maximum number of operators, two cycles have been retained:
- high rate of use > 600 flying hours per year,
- low and medium rate of use < 600 flying hours per year.
These programs are part to the present approved Chapter 5 and are presented as an optional appendix based
on the same tasks and intervals as the A, Z and B inspections.
This document indicates how to "enter" and "leave" the program, and gives the rules and instructions for use.
6. SERVICING
The aircraft servicing operations are described in the "Operating Manual Ground Servicing ".
This manual contains a daily servicing which is not part of the present aircraft inspection program.
The purpose of the daily servicing is to maximize the dispatch reliability and mission success of the aircraft.
Fluid level checks and replenishment are not part of the present maintenance program but are described in
the "Operating Manual - Ground Servicing".
The present maintenance program is based on the assumption that the aircraft is operated and serviced in
accordance with this operating document and that fluid level checks and replenishment (oil, hydraulic fluid,
oxygen, tire pressure, draining) are performed as required, based upon usage and consumption.
7. BASIC INSPECTION
The basic inspection must be performed every 60 days or 200 flying hours (first limit reached). A tolerance of
5 days may be used.
The basic inspection operations are listed in the maintenance procedure 05-60-00-200-801 (Refer to TASK
05-60-00-200-801).
NOTE: If the A/C has not flown for more than 65 days it is considered as a storage A/C. Refer to
10-10-00-550-801 (Refer to TASK 10-10-00-550-801) for storage and removal from storage
instructions.
8. LIST OF AIRCRAFT MAINTENANCE OPERATIONS

The recommended maintenance operations to be performed on the aircraft are listed in tabular form as follows:
A. Column 1: Scheduled maintenance task number, may be either:
• A procedure number (12 digits), in accordance with the AMM procedures numbering system. In this
case, the whole procedure (all operations of the procedure) must be performed at the required interval.
• An operation number (14 digits), the first 12 digits being the AMM procedures number. In this case,
only the operation codes listed have to be performed at the required interval.
B. Column 2: Task title: Description of the procedure or of the operation in accordance with the AMM.
Effectivity: ALL
05-10-00
page 5 / 6
FALCON 900EX EASY
C. Column 3: Interval: Interval at which the task is to be performed and repeated.
D. Column 4: Effectivity: May be for example:

• Blank: the task is applicable to all aircraft.
• A Part Number: the task is applicable only to indicated P/N.
• With Mxxx, Without Mxxx, with SBxxx, Without SB xxxx: the task is applicable to any aircraft on which
modification or SB is or is not embodied.
• A/C xxx to xxx : the task is applicable to aircraft A/C xxx to xxx included.
E. Column 5: Source: Reserved.
F. Column 6: Note: Notes or comments related to the procedure/operation or its interval.

- The numbered notes are listed in section 05-00-00.
9. UPDATING OF SECTION 05-10-00
A. A new operation
A new maintenance operation, introduced by a revision or temporary revision of chapter 5 section
05-10-00 will have to be performed when the next inspection for which it is scheduled falls due.
Any exception to this rule will be stated in the revision.
Example:
New operation due at 2B inspection and aircraft with inspection 2B already performed: operation to be
scheduled at next B inspection then at each multiple of the 2B inspection interval.
New operation due at 2C inspection and aircraft with inspection 2C already performed: operation to be
scheduled at next C inspection then at each multiple of the 2C inspection interval.
NOTE: Regarding the Optimized Continuous Inspection Program, the manufacturer integrates this new
operation and releases to the operator an updated print-out which defines the maintenance block
where the operation is to be performed.
B. An interval change
If the interval of an operation is changed in a revision, check that the interval between the last time this
operation was performed and the next due inspection does not exceed the new interval value. If it does,
perform the operation at a convenient time not to exceed the recommended interval.
Effectivity: ALL
05-10-00
page 6 / 6
FALCON 900EX EASY
05-10 CHAPTER 05 : TIME LIMITS / MAINTENANCE CHECKS
Scheduled
maintenance Task title Interval Effectivity Source Notes
task number
05-60 BASIC INSPECTION
05-60-00-200-801-01 Every (60 D + 5 D) or

BASIC INSPECTION See 5-40
05-102 200 FH
This part of the Basic Inspection does not
05-60-00-200-801-03 BASIC INSPECTION - SERVICING Every (60 D + 5 D) or need to be performed again if already
05-102 OPERATIONS 200 FH performed in the last 5 days before Basic
Inspection.
Effectivity: ALL
"DASSAULT AVIATION Proprietary Data" 05-10-05
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
21-30 PRESSURIZATION
21-30-00-790-802 IN-FLIGHT LEAK CHECK OF THE Or procedure 21-30-00-790-801 (Ground

1B
21-301 CABIN SEALING check of cabin sealing)
21-31-00-720-801 FUNCTIONAL TEST OF THE NOSE
1B
21-307 CONE PRESSURIZATION SYSTEM
FUNCTIONAL TEST OF THE NOSE
21-31-01-720-801
CONE OVERHEAT INDICATING 1B
21-201 SYSTEM
21-32-00-710-801 OPERATIONAL TEST OF THE CABIN
1B
21-302 PRESSURIZATION SYSTEM
OPERATIONAL TEST OF THE
21-32-00-710-802
EMERGENCY SUPPLY OF 1B
21-303 PRESSURIZATION SYSTEM
21-32-00-790-801 LEAK CHECK AROUND THE STATIC Specific RVSM
Z
21-321 PRESSURE PROBES requirement
INSPECTION OF THE BAGGAGE
21-32-17-200-801
COMPARTMENT PRESSURE RELIEF 1B
21-304 VALVES
FUNCTIONAL TEST OF THE BAGGAGE
21-32-17-720-801
COMPARTMENT PRESSURE RELIEF 1C
21-305 VALVES
21-32-33-710-801
BAGGAGE COMPARTMENT 1A
21-202 ISOLATION VALVE
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
task number
INSPECTION OF THE BAGGAGE
21-32-37-200-801
COMPARTMENT NEGATIVE 1B
21-306 PRESSURE RELIEF VALVES
21-32-41-200-801 INSPECTION OF THE NICOTINE
1C More often if necessary
21-316 FILTER CARTRIDGE
21-50 COOLING
21-52-00-710-801 OPERATIONAL TEST OF THE WATER

2B
21-507 REINJECTION SYSTEM
TURBOCOOLER OIL SERVICING -
21-52-05-610-801-02
TURBOCOOLER (504HN) OIL 2A
21-501 DRAINING AND REFILLING
21-52-09-210-802 GENERAL VISUAL INSPECTION OF
1 A+
21-503 THE ECU HEAT EXCHANGER GRID
When you receive the original edition of
chapter 5 DGT 125289, check that the due
21-52-18-100-801 CLEANING OF THE HP WATER
3A interval will be correctly respected.
21-505 SEPARATOR FILTER
Otherwise perform this operation at the next
A visit.
21-52-19-200-801 INSPECTION / CHECK OF THE LP More often if aircraft operated in a high
1 A+
21-508 WATER SEPARATOR COMPONENTS humidity environment
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
05-10 CHAPTER 22 : AUTO FLIGHT
Scheduled
task number
22-10 AUTOMATIC FLIGHT CONTROL SYSTEM (AFCS)

22-10-00-710-801
AUTOMATIC FLIGHT CONTROL 2A Also RVSM requirement
22-100 SYSTEM (AFCS)
CHECK OF THE AUTOPILOT
22-10-07-700-801
SERVOMOTOR CABLES AND 1C Also RVSM requirement
22-102 PULLEYS
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 23 : COMMUNICATIONS
Scheduled
task number
23-10 SPEECH COMMUNICATIONS
See 5-40
23-11-17-710-801 OPERATIONAL TEST OF THE "VHF 1
1B chapter 5 DGT 125289, check that the due
23-110 EMERG" RADIO TUNING SWITCH
interval will be correctly respected.
Otherwise calculate the first due interval.
23-50 AUDIO INTEGRATING
See 5-40
23-50-00-710-802 OPERATIONAL TEST OF THE "BKUP"
1B chapter 5 DGT 125289, check that the due
23-503 AUDIO BUTTON
interval will be correctly respected.
23-60 STATIC DISCHARGERS
VISUAL INSPECTION AND

23-60-00-760-801
ELECTRICAL BONDING CHECK OF 1B
23-602 THE STATIC DISCHARGERS
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
24-30 DC GENERATION
24-30-00-710-801 OPERATIONAL TEST OF THE

1B
24-304 VOLTAGE MONITORING CIRCUITS
OPERATIONAL TEST OF THE APU
24-30-00-710-802
SHUTDOWN SAFETIES WITH 1B
24-313 "MASTER" APU CONTROL
24-40 EXTERNAL POWER
FUNCTIONAL TEST OF THE GROUND

24-40-00-720-801
POWER RECEPTACLE 1B
24-400 OVERVOLTAGE PROTECTION PCB
FUNCTIONAL TEST OF BATTERY
24-41-00-720-801-01 A/C with M3420 or SB
CHARGING BY GPU - GENERAL TEST 1B
24-930 OF THE FUNCTION F900EX-150
24-41-00-720-801-02 A/C with M3420 or SB
CHARGING BY GPU - TEST OF 1B
24-930 SAFETY DEVICES F900EX-150
24-41-00-720-801-03 CHARGING BY GPU - TEST OF THE A/C with M3420 or SB
1A
24-930 EASY INTERFACE TIME DELAY RELAY F900EX-150
(713PD)
24-60 DC LOAD DISTRIBUTION
24-63-13-710-801 OPERATIONAL TEST OF THE DOME

1B
24-323 LIGHTS PCB
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
25-00 GENERAL
25-00-01-200-801
INSPECTION OF THE ONBOARD KIT 2 A+
25-605
INSPECTION OF THE CREW AND
25-00-05-200-801
PASSENGER SEAT HARNESSES AND 1 C
25-000 SAFETY BELTS
25-00-09-200-801 CHECK OF THE CLOSING AND FAA A.D. 74-08-09 and "Arrete" dated April
2A
25-200 SEALING OF TRASH CANS 5th 1989
25-10 COCKPIT
25-11-13-640-801 GREASING OF THE PILOT SEAT

1B
25-100 ACTUATOR ROD END-FITTINGS
25-11-25-200-801 INSPECTION OF THE PILOT SEAT
1C
25-105 ROLLER PINS
25-60 EMERGENCY EQUIPMENT
25-60-00-200-801 INSPECTION OF THE SAFETY

2 A+
25-600 EQUIPMENT
1A
25-603 EMERGENCY LOCATOR SYSTEM
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
26-10 DETECTION
26-10-00-720-802 FUNCTIONAL TEST OF THE PINPOINT

2B
26-105 FIRE DETECTORS
26-20 EXTINGUISHING
CHECK OF THE CORRECT

26-20-01-760-801
OPERATION OF FIRE EXTINGUISHER 1C
26-201 CONTROL SWITCHES
26-20-11-700-801 CHECKING EXTINGUISHING LINES
1C
26-216 FOR CLOGGING
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
27-00 GENERAL
27-00-00-640-801 PRESSURE GREASING OF THE

2C
27-004 SERVO-ACTUATOR BEARINGS
PRESSURE GREASING /
27-00-00-640-802
LUBRICATION OF FLIGHT CONTROL 2C
27-006 RODS AND BELLCRANKS BEARINGS
REMOVAL / INSTALLATION OF THE
27-00-00-640-805 FLIGHT CONTROL SEALED BOXES
2C
27-013 FOR VISUAL INSPECTION AND
GREASING OF BEARINGS
27-00-00-710-801 OPERATIONAL TEST OF THE FLIGHT
1B
27-000 CONTROLS
27-00-00-710-802 OPERATIONAL TEST OF THE TRIM
1C
27-001 SYSTEMS
27-00-00-720-804 CHECK OF THE AUXILIARY AFU NON-
2C See 5-40
27-009 DISCONNECTION
27-00-00-790-804 CHECK OF THE INTERNAL LEAKS OF
3 C then every 1 C
27-007 SERVO-ACTUATORS
27-10 AILERONS AND SPOILERS
GREASING / LUBRICATION OF THE

27-13-01-640-802
ROLL CONTROL BALL BUSHINGS IN 1C
27-102 PRESSURIZED AREA
Effectivity: ALL
page 1 / 5
FALCON 900EX EASY
Scheduled
task number
27-13-01-640-803 ROLL CONTROL LINKAGE
Z
27-101 COMPONENTS OUTSIDE
PRESSURIZED AREA
REMOVAL / INSTALLATION OF THE
27-13-03-220-801
FR15 ROLL BELLCRANKS FOR 1C
27-133 INSPECTION AND GREASING
27-14-05-720-801 FUNCTIONAL TEST OF THE ROLL
2C See 5-40
27-104 TRIM CONTROL SAFETY RELAYS
PRESSURE GREASING OF THE ROLL
27-15-01-640-801
ARTHUR VARIABLE BELLCRANK 2C
27-103 BEARINGS
27-15-01-720-801 FUNCTIONAL TEST OF THE ROLL
1C
27-107 ARTHUR VARIABLE BELLCRANK
27-15-07-640-801 PRESSURE GREASING OF THE ROLL
2C
27-105 AUXILIARY AFU BEARING
27-20 RUDDER
LUBRICATION OF YAW CONTROL

27-23-01-640-801
LINKAGE HINGES OUTSIDE 1C
GREASING OF YAW CONTROL
27-23-01-640-802
LINKAGE BALL-BUSHINGS OUTSIDE Z
27-23-01-640-804
YAW CONTROL BALL BUSHINGS IN 1C
27-24-05-720-802 FUNCTIONAL TEST OF THE YAW TRIM
2C See 5-40
27-206 CONTROL SAFETY RELAYS
Effectivity: ALL
page 2 / 5
FALCON 900EX EASY
Scheduled
task number
27-30 ELEVATORS
27-31-01-640-801 GREASING OF THE CONTROL

2C
27-021 COLUMNS
27-33-01-640-801 PITCH CONTROL LINKAGE
1C
27-303 COMPONENTS OUTSIDE
PRESSURIZED AREA
GREASING OF THE PITCH CONTROL
27-33-01-640-802
LINKAGE BALL-BUSHING OUTSIDE Z
27-33-01-640-803
PITCH BALL-BUSHINGS IN 1C
27-35-00-720-801 FUNCTIONAL TEST OF THE PITCH
2B
27-308 ARTHUR CONTROL SYSTEM
PRESSURE GREASING OF THE PITCH
27-35-01-640-801
ARTHUR VARIABLE BELLCRANK 2C
27-306 BEARINGS
27-35-07-640-801 PRESSURE GREASING OF THE PITCH
2C
27-307 AUXILIARY AFU BEARINGS
27-40 HORIZONTAL STABILIZER
FUNCTIONAL TEST OF THE

27-40-00-720-801
HORIZONTAL STABILIZER CONTROL 1 B
27-404 AND INDICATING SYSTEM
GREASING OF THE HORIZONTAL
27-40-01-640-802
STABILIZER ACTUATOR HINGES AND 2 A
27-401 JACK SCREW
Effectivity: ALL
page 3 / 5
FALCON 900EX EASY
Scheduled
task number
OPERATIONAL TEST OF THE RELAY
27-40-15-710-801
IN THE HORIZONTAL STABILIZER 2C See 5-40
27-411 EMERGENCY CONTROL BOX
27-40-17-720-801 FUNCTIONAL TEST OF THE
3B See 5-40
27-405 HORIZONTAL STABILIZER RELAY BOX
27-50 FLAPS
27-50-00-640-802 GREASING / LUBRICATION OF THE

2A
27-501 FLAP MECHANISM HINGES
27-50-00-640-803 CLEANING / GREASING OF THE FLAP
1A
27-500 SCREW JACK ACTUATING SCREWS
FUNCTIONAL TEST OF THE FLAP
27-50-00-720-801-01
CONTROL AND INDICATING SYSTEM - 1 B
27-503 USING THE HYDRAULIC GPU
27-50-00-720-802 FUNCTIONAL TEST OF THE FLAP
1A See 5-40
27-502 ASYMMETRY DETECTION SYSTEM
27-50-00-720-803 CHECK OF THE GEAR BACKLASH OF
2 B then every 1 B
27-508 FLAP LINKAGE
27-52-13-200-801 CHECK / GREASING OF FLAP
1C
27-507 CONTROL ROD SPLINES
27-60 AIRBRAKES

1B
27-605 AIRBRAKES IN NORMAL MODE
27-61-00-720-801
AUTOMATIC AIRBRAKE EXTENSION 1A See 5-40
27-610 CIRCUIT ("BSCU HARDWARE" RELAY)
Effectivity: ALL
page 4 / 5
FALCON 900EX EASY
Scheduled
task number
27-61-00-720-802 AUTOMATIC AIRBRAKE EXTENSION
1A See 5-40
27-611 CIRCUIT ("LH THROTTLE" and "RH
THROTTLE" RELAYS)
27-61-00-720-803
27-612 CIRCUIT ("BSCU SOFTWARE" RELAY)
27-61-00-720-806
27-615 CIRCUIT (MONITORING SYSTEM)
27-80 SLATS
27-80-00-640-801 GREASING / LUBRICATION OF THE

2 A+
27-800 SLAT MECHANISMS
27-80-00-720-801
FUNCTIONAL TEST OF THE SLATS 1B See 5-40
27-803
27-80-17-720-802 FUNCTIONAL TEST OF THE SLAT /
2B
27-802 FLAP POSITION MICROSWITCHES
Effectivity: ALL
page 5 / 5
FALCON 900EX EASY
Scheduled
task number
28-00 GENERAL
28-00-00-280-801 CHECK FOR NON-CONTAMINATION

1A And more often if necessary
28-001 OF THE FUEL
28-10 STORAGE
28-10-00-280-801 SPECIAL DETAILED INSPECTION OF

1C
28-101 THE FUEL TANK FLAPPER VALVES
28-20 DISTRIBUTION
28-21-13-710-801 OPERATIONAL TEST OF THE FUEL

1C See 5-40
76-200 SHUT-OFF VALVES
28-21-13-790-801 LEAK TEST OF THE FUEL SHUT-OFF During engine
76-202 VALVES Removal for MPI
2A
28-302 CROSSFEED UNITS
Also at 25-75 and 100-150 hours following
CLEANING OF THE CROSSFEED UNIT
28-21-29-100-801 delivery or C inspection or following a
FILTERS AND BOOSTER PUMP 2 UNIT 2 A
28-301 FILTER removal of the wing removable panel and
more often if necessary
28-22-00-710-802 OPERATIONAL TEST OF THE MANUAL
1B
28-308 FUEL TRANSFER TO REAR TANK
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
task number
28-30 DRAINING AND DEFUELING
28-30-00-680-803 DRAINING OF THE GRAVITY Every (60 D + 5 D) or A/C with P/N

28-705 DEFUELING LINE 200 FH L88A31-663 (M32WB)
28-40 INDICATING
28-41-00-720-801 FUNCTIONAL TEST OF THE FUEL

2B
28-500 QUANTITY INDICATING SYSTEM
28-43-01-720-801 FUNCTIONAL TEST OF THE FUEL
1C
28-504 TEMPERATURE SENSOR
28-70-01-780-801 CHECK FOR CORRECT CALIBRATION

1C
28-207 OF THE PRESSURE GAUGE
28-70-17-130-801 CLEANING OF FUEL TANK
1B
28-200 PRESSURIZATION AIR FILTERS
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
task number
29-10 PRIMARY HYDRAULIC POWER
29-10-00-720-801 FUNCTIONAL TEST OF THE MAIN

1C
29-100 HYDRAULIC SYSTEMS
29-14-01-680-801 DRAINING OF THE HYDRAULIC
1C
29-111 RESERVOIRS
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
30-00 GENERAL
30-00-00-960-801 REPLACEMENT OF THE ANTI-ICING

2C
30-108 SYSTEM WIGGINS COUPLING SEALS
30-10 WING ANTI-ICING
INSPECTION OF THE WING ANTI-

30-11-17-200-803
ICING SYSTEM GENERAL 1C
30-107 CONNECTOR COUPLINGS
30-20 ENGINE AIR INTAKE ANTI-ICING
30-20-00-710-801 OPERATIONAL TEST OF THE ENGINE

1B
30-200 AIR INTAKE ANTI-ICING SYSTEM
30-30 PROBE ANTI-ICING
30-30-00-710-801 OPERATIONAL TEST OF THE AIR

1B
30-300 DATA PROBE ANTI-ICING SYSTEM
30-40 WINDOWS, WINDSHIELDS AND DOORS

3B
30-400 WINDSHIELD ANTI-ICING SYSTEM
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
task number
30-90 BRAKE HEATING
30-90-00-710-801 OPERATIONAL TEST OF THE BRAKE A/C with SB

1B
30-110 HEATING SYSTEM F900EX-230 or M5505
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
task number
31-30 RECORDERS
31-31-00-710-802 OPERATIONAL TEST OF THE FLIGHT

2 A+
31-300 DATA RECORDER (FDR) SYSTEM
31-31-00-720-801 FUNCTIONAL TEST OF THE 88- Refer to country of
31-307 PARAMETER FDR registration
31-31-00-970-801 DOWNLOAD OF THE FLIGHT DATA Refer to country of
31-311 RECORDER (FDR) registration
31-31-35-700-801 CHECK OF THE FLIGHT CONTROL
4 A+
22-107 INPUT FORCE SENSORS
31-31-50-710-801
COCKPIT VOICE RECORDER (CVR) 2 A+
23-700 SYSTEM
31-60 CENTRAL DISPLAY SYSTEM (CDS)
See 5-40
OPERATIONAL TEST OF THE When you receive the original edition of
31-60-00-710-801-08
CENTRAL DISPLAY SYSTEM (CDS) - 1B chapter 5 DGT 125289, check that the due
31-600 REVERSION CONTROLLER (34FV) interval will be correctly respected.
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
32-00 GENERAL
A/C with NLG uplock

CHECK OF THE MLG AND NLG
32-00-00-700-801-01 box (P/N C24245006 or
UPLOCK BOXES - NLG UPLOCK BOX 2 A+
32-320 (13GA) P/N C24245006-1 or
P/N C24245006-2)
A/C with LH MLG uplock
CHECK OF THE MLG AND NLG
32-00-00-700-801-02 box (P/N C24244007 or
UPLOCK BOXES - LH MLG UPLOCK 2 A+
32-320 BOX (L7GA) P/N C24244007-1 or
P/N C24244007-2)
A/C with RH MLG
CHECK OF THE MLG AND NLG uplock box (P/N
32-00-00-700-801-03
UPLOCK BOXES - RH MLG UPLOCK 2 A+ C24245007 or
32-320 BOX (R7GA) P/N C24245007-1 or
P/N C24245007-2)
32-10 MAIN LANDING GEARS (MLG) AND MLG DOORS
32-10-00-640-801 LUBRICATION OF THE MAIN LANDING

1A
32-100 GEARS (MLG) AND MLG DOORS
CHECK OF THE CHARGING
32-11-05-780-801
PRESSURE OF THE MLG SHOCK 1B
32-111 ABSORBERS
Effectivity: ALL
page 1 / 3
FALCON 900EX EASY
Scheduled
task number
32-20 NOSE LANDING GEAR (NLG) AND NLG DOORS
32-20-00-640-801 LUBRICATION OF THE NOSE LANDING

1A
32-200 GEAR (NLG) AND NLG DOORS
32-21-01-780-801
PRESSURE OF THE NLG SHOCK 1B
32-212 ABSORBER
32-21-01-780-802 PRESSURE OF THE NLG SHOCK A/C without M5028 or This check can also be performed using MP
2 A+
32-210 ABSORBER BY APPLYING A without SB F900EX-265 32-21-01-780-801
ROTATIONAL TORQUE
32-30 EXTENSION AND RETRACTION
FUNCTIONAL TEST OF EXTENSION

32-30-00-720-801
AND RETRACTION OF LANDING 1B
32-300 GEARS AND DOORS
CHECK OF THE LANDING GEAR
32-31-00-700-801
RETRACTION INHIBITION ON THE 1B
32-303 GROUND
LUBRICATION OF THE LANDING GEAR
32-32-00-640-801
MECHANICAL EMERGENCY RELEASE 2 A+
32-302 CONTROL CABLES
LUBRICATION OF THE LANDING GEAR
32-32-17-640-801
HYDRAULIC EMERGENCY 2 A+
32-301 EXTENSION CONTROL CABLE
32-40 WHEELS AND BRAKES
32-41-00-220-801 DETAILED INSPECTION OF THE

Z
32-420 BRAKE LINKAGE CONTROL
Effectivity: ALL
page 2 / 3
FALCON 900EX EASY
Scheduled
task number
SERVICING OF THE PEDAL
32-41-07-610-801
INTERCONNECTION FLEXIBLE 1C
32-422 CONTROLS
2B
32-444 HYDRAULIC FUSES
32-42-00-610-801 SERVICING OF THE PARK BRAKE
2 A+
32-425 CONTROL
32-42-05-720-801 FUNCTIONAL TEST OF THE PARK
4 A+
32-408 BRAKE ACCUMULATOR CAPACITY
Effectivity: ALL
page 3 / 3
FALCON 900EX EASY
Scheduled
task number
34-10 FLIGHT ENVIRONMENT DATA
CHECK OF THE ELECTRICAL ZERO

34-10-11-720-801
SETTING OF ANGLE-OF-ATTACK 1C
27-804 SENSORS
CHECK OF THE TOTAL PRESSURE
34-11-01-200-801
PROBE DRAIN HOLES FOR 1 A+
34-107 CLOGGING
34-20 ATTITUDE AND HEADING
CHECK OF THE GENERAL-PURPOSE

34-21-00-700-801
BUSES TO THE INERTIAL 3B See 5-40
34-209 REFERENCE SYSTEM (IRS)
34-30 LANDING AND TAXIING AIDS
34-31-00-710-801 OPERATIONAL TEST OF THE HEAD-

2 A+ A/C with HUD
34-321 UP GUIDANCE SYSTEM (HGS)
34-32-01-100-801
CLEANING OF THE ISU LENS 2A A/C with EFVS More often if necessary
34-935
34-32-01-780-801 PRESSURE CHECK OF THE
2A A/C with EFVS
34-931 INFRARED SENSOR UNIT (ISU)
34-32-05-100-801 CLEANING OF THE INFRARED
2A A/C with EFVS More often if necessary
34-936 WINDOW (IRW)
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
35-20 PASSENGER OXYGEN SYSTEM
GENERAL VISUAL INSPECTION OF

35-20-00-210-801 THE PASSENGER OXYGEN MASKS,
2 A+
35-208 PORTABLE OXYGEN MASKS AND
SMOKE MASKS
1B See 5-40
35-200 PASSENGER OXYGEN SYSTEM
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
36-10 DISTRIBUTION / BLEED AIR
A/C with P/N

36-10-29-280-801 SPECIAL DETAILED INSPECTION OF At each engine 2
FGFB721551300D2
36-110 THE ENGINE 2 BLEED AIR HP PIPE removal for MPI
pipe
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 38 : WATER - WASTE
Scheduled
task number
38-00 GENERAL
38-00-00-610-801
SERVICING OF THE WATER SYSTEM 2 A+
38-106
38-10 POTABLE WATER SYSTEM
38-10-00-670-801 STERILIZATION OF THE POTABLE

1 A+ More often if necessary
38-104 WATER SYSTEM
38-30 WASTE WATER DISPOSAL SYSTEM
38-30-00-720-801 FUNCTIONAL TEST OF THE WASTE

1B
30-700 WATER DRAIN ANTI-ICING SYSTEM
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 45 : CENTRAL MAINTENANCE SYSTEM (CMS)
Scheduled
task number
45-90 DATA LOADING
INTEGRITY CHECK OF SOFTWARE IN Monthly (with a non

45-92-00-700-801-01
AVIONICS MODULES - CHECK ALL cumulative tolerance Before SB F900EX-304
45-403 MODULES of 10 days)
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
52-00 GENERAL
52-00-00-200-801 INSPECTION / CHECK OF THE DOORS

1C
53-022 SEALS
LUBRICATION OF THE VISIBLE DOOR
52-00-00-640-801
HINGES AND PASSENGER DOOR 1A
52-000 STOPS
52-10 PASSENGER DOOR
52-10-00-610-801 SERVICING OF THE PASSENGER

4 A+
52-103 DOOR
LUBRICATION OF THE ROLLERS OF
52-10-00-640-801
THE PASSENGER DOOR LOWER 2C
52-109 MECHANISM
1C
52-20 EMERGENCY EXIT DOOR
52-20-00-610-801 SERVICING OF THE EMERGENCY

2 A+ See 5-40
52-205 EXIT DOOR
52-20-00-710-801
EMERGENCY EXIT DOOR 1B
52-201 UNLOCKING FROM OUTSIDE
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
task number
52-30 BAGGAGE COMPARTMENT DOOR
52-30-00-610-801 SERVICING OF THE BAGGAGE

2 A+
52-304 COMPARTMENT DOOR
1C See 5-40
52-302 BAGGAGE COMPARTMENT DOOR
52-40 SERVICE DOORS

Z
52-410 THE SERVICE DOORS
52-41-07-610-801 SERVICING OF THE NLG WELL
Z
52-411 CEILING DOOR
52-50 INTERNAL ACCESSES
52-53-00-610-801 SERVICING OF THE CABIN / BAGGAGE

2 A+
52-500 COMPARTMENT DOOR
52-55-00-610-801
SERVICING OF THE S-DUCT DOOR Z
52-501
52-60 SERVICING COMPARTMENT DOOR
52-60-09-610-801 SERVICING OF THE MECHANIC'S

4 A+
52-400 SERVICING COMPARTMENT DOOR
52-70 DOOR INDICATING
52-70-00-710-802 OPERATIONAL TEST OF THE DOOR

4 A+
52-701 INDICATING SYSTEM
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
05-10 CHAPTER 53 : FUSELAGE
Scheduled
task number
53-00 GENERAL
INSPECTION OF THE FUSELAGE

53-00-00-200-801-01
EXTERIOR - GENERAL VISUAL Z
53-000 INSPECTION
53-00-00-200-801-02 INSPECTION OF THE FUSELAGE
1C
53-000 EXTERIOR - DETAILED INSPECTION
INSPECTION OF THE FUSELAGE SKIN
53-00-00-200-803-01 At 11250 FC then
- FRAME 4 TO FRAME 30 - GENERAL See 5-40
53-025 VISUAL INSPECTION every 3750 FC
53-00-00-200-803-02 At 11250 FC then
- FRAME 4 TO FRAME 30 - DETAILED See 5-40
53-025 INSPECTION IN SPECIFIC AREAS every 3750 FC
53-10 T12 SECTION AND NOSE CONE
53-10-00-200-808
INSPECTION OF THE NLG BAY 1 A+
53-021
53-10-00-200-810-01 At 7500 FC then
- FRAME 0 TO FRAME 4 - GENERAL See 5-40
53-024 VISUAL INSPECTION every 3750 FC
53-10-00-200-810-02 At 11250 FC then
- FRAME 0 TO FRAME 4 - DETAILED See 5-40
53-024 INSPECTION IN SPECIFIC AREAS every 3750 FC
Z
53-003 THE FLIGHT COMPARTMENT
Effectivity: ALL
page 1 / 5
FALCON 900EX EASY
Scheduled
task number
DETAILED INSPECTION OF THE
53-10-00-220-801 Specific RVSM
STATIC PRESSURE PROBE AND OF Z
53-026 THE FUSELAGE SKIN IN PROBE AREA requirement
1C
53-004 FLIGHT COMPARTMENT
53-10-01-250-801 EDDY CURRENT INSPECTION OF THE
2 C then every 1 C
53-032 FRAME 0 STIFFENER TIP
SPECIAL DETAILED INSPECTION OF
53-10-03-250-801
THE UPPER PASSENGER DOOR 3 C then every 1 C See 5-40
53-031 FRAME EDGING
INSPECTION OF THE LOWER
53-10-39-220-801
SECTION OF THE COCKPIT 1C
53-501 WINDSHIELD / WINDOW FRAMES
53-10-39-220-802
COCKPIT WINDSHIELD / WINDOW 3 C then every 1 C
53-037 FRAMES
Z
53-001 THE NOSE CONE AREA
53-11-00-220-801 DETAILED INSPECTION OF THE NOSE
1C
53-002 CONE AREA
53-11-00-760-801 CHECK OF THE NOSE CONE
2 A+
53-408 ELECTRICAL BONDING
53-11-21-960-801 REPLACEMENT OF THE NOSE CONE Can be performed during C-Check prior to
Every 7500 FC
53-404 SEAL 7500 FC
53-30 T34 UPPER SECTION

Z
53-006 THE PASSENGER CABIN
Effectivity: ALL
page 2 / 5
FALCON 900EX EASY
Scheduled
task number
53-30-00-220-801-01
PASSENGER CABIN - UNDER THE 1C
53-007 FLOOR
53-30-00-220-801-02
PASSENGER CABIN - ABOVE THE 2C
53-007 FLOOR
EDDY CURRENT INSPECTION OF THE
53-30-00-250-801 PASSENGER CABIN SKIN PANEL
1C See 5-40
53-028 AROUND EMERGENCY EXIT DOOR
ROUNDED ANGLES
EDDY CURRENT INSPECTION OF THE
53-30-00-250-802
SKIN PANELS AROUND CABIN 2 C then every 1 C See 5-40
53-027 WINDOW CUT-OUTS
53-40 T34 LOWER SECTION
53-40-00-200-804
INSPECTION OF THE MLG BAYS 1 A+
53-019
53-40-00-210-802
THE FUSELAGE LOWER SECTION Z
53-009 AREAS
1C
53-010 FUSELAGE LOWER SECTION AREAS
53-40-00-220-802
FUSELAGE STRUCTURAL FUEL 1C
53-008 TANKS
53-41-00-220-801 DETAILED INSPECTION OF THE WING
Z
57-006 ROOT UPPER BOLT RECESSES
53-41-00-220-802 DETAILED INSPECTION OF THE WING
1C See 5-40
53-023 ROOT LOWER BOLT RECESSES
Effectivity: ALL
page 3 / 5
FALCON 900EX EASY
Scheduled
task number
RENEWAL OF THE TEMPORARY
53-41-00-620-802
PROTECTION OF THE WING ROOT 1C
57-007 BOLT RECESSES
53-41-01-640-801 LUBRICATION OF THE WING TO
1C
57-002 FUSELAGE CONNECTING ROD
53-50 T5 SECTION

53-50-00-210-804
THE MECHANIC'S SERVICING 1 A+
53-014 COMPARTMENT
Z
53-012 THE BAGGAGE COMPARTMENT
2 A+
53-016 THE APU AREA
1C
53-013 BAGGAGE COMPARTMENT
53-50-00-220-805
MECHANIC'S SERVICING 1C
53-015 COMPARTMENT
53-50-30-250-802 EDDY-CURRENT INSPECTION OF THE
2 C then every 1 C
53-036 REAR EDGE OF BEAMS AT FRAME 30
53-60 T34 BODY FAIRINGS
53-60-00-760-801 CHECK OF THE FUSELAGE VENTRAL

4 A+
53-505 FAIRING ELECTRICAL BONDING
Effectivity: ALL
page 4 / 5
FALCON 900EX EASY
Scheduled
task number
53-80 DRAINING
CHECK OF THE FUSELAGE

53-80-00-200-801
CONDENSATION AND STREAM 2 A+
51-004 WATER DRAINS
53-80-09-710-801 OPERATIONAL TEST OF THE "CIRCLE In high humidity environment, check at "2A
1C
51-005 SEAL" AUTOMATIC DRAINS +" inspection
Effectivity: ALL
page 5 / 5
FALCON 900EX EASY
05-10 CHAPTER 54 : NACELLES AND PYLONS
Scheduled
task number
54-00 GENERAL

54-00-00-210-810 May be performed during an engine
THE ENGINE 1 AND 3 NACELLES AND 2A
54-000 PYLONS inspection without exceeding a 2A interval
54-00-00-210-811 GENERAL VISUAL INSPECTION OF May be performed during an engine
2A
54-002 THE ENGINE 2 NACELLE inspection without exceeding a 2A interval
54-00-00-220-801 May be performed during an engine removal
ENGINE 1 AND 3 NACELLES AND Every 3750 FC
54-001 PYLONS prior to 3750 FC.
54-00-00-220-802 DETAILED INSPECTION OF THE May be performed during an engine removal
Every 3750 FC
54-003 ENGINE 2 NACELLE prior to 3750 FC.
54-10 COWLINGS
54-11-00-610-801 SERVICING OF THE ENGINE

2A
54-100 COWLINGS
54-11-00-760-801 CHECK OF THE ENGINE COWLING
2 A+
54-116 ELECTRICAL BONDING
54-40 CENTRAL ENGINE AIR INTAKE / S-DUCT

1A
54-007 THE ENGINE 2 S-DUCT
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 55 : STABILIZERS
Scheduled
task number
55-00 GENERAL

Not to exceed 4000 FH (See 5-40 MP
55-00-00-210-801 THE HORIZONTAL AND VERTICAL
Z 27-003 : ATA 100 number - MP
55-000 STABILIZERS AND OF ENGINE 2 AIR
INTAKE AND S-DUCT 27-00-00-220-801 ATA AMTOSS number)
55-00-00-220-801 HORIZONTAL AND VERTICAL
1C
55-001 STABILIZERS AND OF ENGINE 2 AIR
INTAKE AND S-DUCT
CHECK OF THE STABILIZER
55-00-00-760-801
MOVABLE SURFACE ELECTRICAL Z
55-005 BONDING
ULTRASONIC INSPECTION OF THE

55-10-00-270-801 At (4 C or 11250 FC)
HORIZONTAL STABILIZER HINGE See 5-40
55-002 FITTINGS then every 1 C
GREASING OF THE HORIZONTAL
55-10-00-640-802
STABILIZER FRONT TORQUE LINK Z
27-403 AND ACTUATOR UPPER HINGE
55-10-03-640-801 LUBRICATION OF THE SPRING-
Z
55-100 LOADED FAIRING MECHANISM
DIMENSIONAL CHECK OF
55-10-31-220-801
HORIZONTAL STABILIZER REAR 1C See 5-40
55-501 HINGE BUSHINGS
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
task number
55-10-33-640-801 LUBRICATION OF THE HORIZONTAL
1A
27-400 STABILIZER REAR HINGE PINS
55-10-39-220-801 At 11250 FC then
HORIZONTAL STABILIZER ACTUATOR See 5-40
55-003 ATTACHMENT FITTINGS AND PINS every 3750 FC
55-20 ELEVATORS
55-20-03-640-801 LUBRICATION OF THE ELEVATORS

2C
55-200 BEARINGS
55-20-03-640-802 LUBRICATION OF THE ELEVATOR
1A
27-300 CONTROL SURFACE HINGES
55-20-05-640-801 LUBRICATION OF THE ELEVATOR
2A
27-402 CONTROL BEARINGS AND U-JOINTS
55-30 VERTICAL STABILIZER
ULTRASONIC INSPECTION OF THE

55-30-00-270-801 At (4 C or 11250 FC)
VERTICAL STABILIZER / STUB See 5-40
55-004 ATTACHMENTS then every 1 C
55-40 RUDDER
55-40-05-640-801 LUBRICATION OF THE RUDDER

2C
55-400 BEARINGS
55-40-05-640-802 LUBRICATION OF THE RUDDER
1A
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
05-10 CHAPTER 56 : WINDOWS
Scheduled
task number
56-10 COCKPIT WINDSHIELDS / WINDOWS
56-10-09-640-801 LUBRICATION OF THE OPENING

2 A+
56-100 WINDOW MECHANISM
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 57 : WINGS
Scheduled
task number
57-00 GENERAL
Not to exceed 4000 FH (See 5-40 MP

Z 27-003 : ATA 100 number - MP
57-000 THE WINGS
27-00-00-220-801 ATA AMTOSS number)
1C
57-001 WINGS
57-00-00-760-801 CHECK OF THE WING MOVABLE
Z
57-012 SURFACE ELECTRICAL BONDING
57-10 WING STRUCTURE
57-10-00-290-801 BORESCOPE INSPECTION OF THE

1C
57-003 WING TANKS
57-10-01-210-801 GENERAL VISUAL INSPECTION OF At 11250 FC then
See 5-40
57-008 THE WING LOWER PANELS every 3750 FC
DETAILED INSPECTION OF THE WING
57-10-14-220-801 At 11250 FC then
FRONT SPAR FROM ROOT TO RIB 17 See 5-40
57-060 EXCEPT RIB 6 TO 9 every 7500 FC
57-10-14-220-802 DETAILED INSPECTION OF THE WING At 11250 FC then
See 5-40
57-070 FRONT SPAR FROM RIB 6 TO 9 every 3750 FC
See 5-40
57-090 REAR SPAR 1 FROM ROOT TO 3 every 3750 FC
See 5-40
57-080 REAR SPAR 2 FROM RIB 3 TO RIB 17 every 7500 FC
Effectivity: ALL
page 1 / 3
FALCON 900EX EASY
Scheduled
task number
EDDY-CURRENT INSPECTION OF THE
57-10-15-250-801 At 11250 FC then
RIB 8 REAR WING SPAR SPLICE See 5-40
57-005 PLATE every 3750 FC
57-40 FIXED LEADING EDGE AND SLATS
57-45-25-270-801 EDDY CURRENT INSPECTION OF

3 C then every 2 C
57-540 SLAT TRACKS
57-50 FIXED TRAILING EDGE AND FLAPS
57-55-00-700-801 CHECK OF THE FLAP LATERAL

1C
57-606 CLEARANCE
57-55-07-220-801 PROTECTION ON INBOARD /
1C
57-600 OUTBOARD FLAP JUNCTION FAIRING
FRICTION AREAS
1C
57-601 THE FOREFLAP BRACKETS
57-55-21-250-801 EDDY-CURRENT INSPECTION OF THE
1C
57-607 FLAP TRACKS 2 AND 5
57-60 AILERONS
57-60-05-640-801 PRESSURE LUBRICATION OF THE

1C
57-700 AILERON BEARINGS
57-60-05-640-802 LUBRICATION OF THE AILERON
1A
Effectivity: ALL
page 2 / 3
FALCON 900EX EASY
Scheduled
task number
57-70 AIRBRAKES AND SPOILERS
57-70-03-640-801 LUBRICATION OF THE AIRBRAKE

2 A+
27-600 HINGES
Effectivity: ALL
page 3 / 3
FALCON 900EX EASY
Scheduled
task number
71-20 MOUNTS
No tolerance
71-20-02-250-801 SPECIAL DETAILED INSPECTION OF At 11250 FC then See 5-40
54-004 THE ENGINE 1 AND 3 FRONT MOUNTS every 3750 FC May be performed during engine removal
prior to 11,250 FC then every 3750 FC.
No tolerance
71-20-07-250-801 SPECIAL DETAILED INSPECTION OF At 11250 FC then See 5-40
54-005 THE ENGINE 1 AND 3 REAR MOUNTS every 3750 FC May be performed during engine removal
prior to 11,250 FC then every 3750 FC.
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 73 : ENGINE FUEL AND CONTROL
Scheduled
task number
73-20 CONTROLLING
OPERATIONAL TEST OF THE ENGINE

73-20-01-710-802
1 DIGITAL ELECTRONIC COMPUTER 1 B
76-300 (DEEC 1) ST-BY POWER SUPPLY
73-30 INDICATING
A/C with SB
F900EX-311 (or M5288)
73-30-02-710-801 OPERATIONAL TEST OF THE FUEL
2B even with SB
73-301 FILTER CLOGGING DETECTION
F900EX-296 complied
with
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 76 : ENGINE CONTROLS
Scheduled
task number
76-10 POWER CONTROL
76-10-00-220-801 CHECK OF THE THROTTLE LEVERS

2A
76-100 FOR FRICTION POINTS
76-10-00-220-802 MEASUREMENT OF THE THROTTLE At each engine
76-102 LEVER OPERATING FORCES Removal/Installation
76-10-21-640-802 LUBRICATION OF THE TELEFLEX
1C
76-101 CONTROL CABLE BALL-JOINTS
76-10-25-640-801 GREASING OF THE THROTTLE
2C
76-114 CONTROL TORSION TUBE
76-10-33-820-801 CHECK OF THE THROTTLE CONTROL
1C
76-103 CABLE TENSION
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-10 CHAPTER 77 : ENGINE INDICATING
Scheduled
task number
77-10 POWER
77-11-00-710-801 OPERATIONAL TEST OF THE "ENG 2

1B See 5-40
77-100 FAIL" WARNING INDICATION
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
task number
78-30 THRUST REVERSER

2A
78-300 THE THRUST REVERSER
78-30-00-220-801 DETAILED INSPECTION OF THE During engine
78-303 THRUST REVERSER Removal for MPI
FUNCTIONAL TEST OF THE THRUST
78-30-00-720-801
REVERSER SYSTEM WITH ENGINE 1C
78-301 SHUT DOWN
GREASING OF THE THRUST A/C with (P/N
78-31-00-640-802-01
REVERSER DOOR HINGE BOLTS - A/C 1 A NAS6307U22D or
78-302 WITH NON-PLATED BOLTS P/N NAS6307U23D)
GREASING OF THE THRUST A/C with (P/N
78-31-00-640-802-02
REVERSER DOOR HINGE BOLTS - A/C 1 C NAS6307C22D or
78-302 WITH CHROME-PLATED BOLTS P/N NAS6307C23D)
GREASING OF THE LINK ROD HINGE
78-31-00-640-803-01 A/C with P/N
BOLTS AND DOOR LATCH HOOKS - A/ Z
78-304 C WITH NON-PLATED BOLTS NAS6305U17D
GREASING OF THE LINK ROD HINGE
78-31-00-640-803-02 A/C with P/N
BOLTS AND DOOR LATCH HOOKS - A/ 1 C
78-304 C WITH CHROME-PLATED BOLTS NAS6305C17D
78-32-00-760-801 TEST OF THE GROUND / FLIGHT
1B See 5-40
78-316 RELAY AND TRCU INPUT CIRCUIT
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-20-00
COMPONENT MAINTENANCE OPERATIONS
1. GENERAL
This section lists all work to be performed on these items and establishes their maintenance schedule.
The operations to be performed on these items of equipment when they are removed from the aircraft may
consist of special maintenance operations, functional tests or major overhaul.
The description of operations to be performed on the items of equipment (and list of required equipment) is
to be found in the "Maintenance Manual" (Maintenance Procedures) for maintenance operations which may
be performed on the aircraft and for maintenance operations which may be performed in the vicinity of the
aircraft (without returning the items of equipment to a specialized workshop).
2. SCHEDULED MAINTENANCE OPERATIONS
A. Components Governed by Number of Flying Hours, Landings or Flight Cycles

These components shall undergo maintenance operations when they reach the indicated number of Flying
Hours, Landings or Flight Cycles, or, if close to reaching this limit, at time of a scheduled aircraft inspection.
The length of time in service, for a particular component, is the time accrued during use on different aircraft.
NOTE: The number of landings is the sum of the actual landings + any possible touch and go.
B. Components Governed by Calendar Time

Scheduled maintenance operations on these components must be performed in accordance with
calendar time schedule only, without taking the flying hours or landings into consideration.
C. Components Governed by several parameters

Scheduled maintenance of these components must be performed when the first of these limits is reached.
D. Tolerance of Scheduled Maintenance Operations
A non cumulative tolerance of 3% of the recommended maintenance interval may be used for all
Components unless otherwise specified. There is no tolerance on life limits i.e. replacement/discard.
3. TIME BASE
The time base to be taken into account in order to determine the removal date of equipment depends on the
nature of these items. Unless otherwise specified in this section (05-20) the following instructions apply:
A. Components with calendar scheduled maintenance

For all components the threshold of the first inspection is registered in the Aircraft Inspection Handbook,
or in the component logbooks.
In case of component exchange, the time base will be the date of installation on aircraft for a new or
overhauled component, or the date of the last scheduled maintenance for a used component.
B. Components with life limit / replacement

The date of origin is the date of manufacture marked on the component identification plate, or registered
in the Aircraft Inspection Handbook, or in the component logbooks.
Effectivity: ALL
05-20-00
page 1 / 4
FALCON 900EX EASY
4. UTILIZATION OF COMPONENT MAINTENANCE TABLE
A. The maintenance of the components in accordance with the above paragraphs is listed in a table set out
as follows:
• Column 1: Scheduled maintenance task number:
• An operation number (14 digits), the first 12 digits being the AMM procedures number. In this case,
only the operation codes listed have to be performed at the required interval.
• Column 2: Task title: Description of the operation in accordance with the AMM.
• Column 3: Interval: Interval at which the task has to be performed and repeated.
The interval can be:
• D: Day
• M: Month
• Y: Year
• FH: Flying Hour
• FC: Flight Cycle
• LDG: Landing
• Column 4: Component Functional Index (CFI): Index that allows hyperlink navigation throughout the
maintenance documentation and for electrical component it is also the electrical index.
• Column 5: Effectivity: May be for example:
• Blank: the task is applicable to all component associated to this CFI.
• List of Part Numbers: The task is applicable only to the listed P/Ns. Note: A P/N in the list may not
be applicable to your aircraft. Refer to the IPC for this information.
• With Mxxx, Without Mxxx, with SBxxx, Without SB xxxx: the task is applicable to any aircraft on
which modification or SB is or is not embodied.
• A/C xxx to xxx : the task is applicable to aircraft A/C xxx to xxx included.
• Column 6: Source: Reserved.
• Column 7: Note: Notes or comments related to the procedure/operation or its interval.
The numbered notes are listed in section 05-00-00.
B. Definitions of maintenance type

• OPERATIONAL CHECK: Task to determine if an item is fulfilling its intended purpose. The task does
not require quantitative tolerances.
NOTE: This check is normally performed on the A/C using the installed system.
• FUNCTIONAL CHECK: Quantitative check to determine if one or more functions of an item performs
within specified limits.
NOTE: This check may require supplemental ground support equipment or the removal of an item of
equipment from the aircraft.
• INSPECTION CHECK: A visual inspection required to determine the condition of an item of equipment
or one of its components, unless special techniques or tools are required.
• SERVICING: Servicing operation including: cleaning, lubrication, greasing, conditioning of a
component or an item or equipment.
• CALIBRATION CHECK: Characteristics measurements:
Measuring of component settings and the comparison of these readings with established tolerances;
requires a measuring test bench.
Effectivity: ALL
05-20-00
page 2 / 4
FALCON 900EX EASY
• HYDROSTATIC TESTING: Check by application of a specific test pressure within vessels normally
containing pressurized fluids.
• REPLACEMENT/DISCARD: Replacement/discard of the component.
• RESTORATION: That work necessary to return the component to a specific standard. Since
restoration may vary from cleaning or replacement of single parts up to a complete overhaul, the scope
of each restoration task is described:
• In the title of the task (general description),
• In the overview of the task documented in the AMM (more detailed description).
NOTE: If the scope of the restoration task is not provided, a complete overhaul of the component has
to be performed.
OVERHAUL: Major restoration task with specific impact on the time base considered for the next
scheduled removal of the component (Refer to para. 3. “TIME BASE”).
5. OPERATIONS AFTER RE-INSTALLATION OF COMPONENT ON AIRCRAFT

After re-installation of a component on the aircraft, an operational or functional check of the corresponding
system is to be performed unless otherwise specified in a Removal/Installation procedure.
6. UPDATING OF SECTION 05-20-00
A. New maintenance operation

A new maintenance operation on equipment introduced by a revision or temporary revision of chapter 5
section 05-20-00 will have to be performed when the time at which it is scheduled falls due. Should this
time have gone past, the operation shall be performed at next aircraft inspection (A or Z or B or C).
B. Example:
C. Interval change
If the interval of an operation is changed in a revision, check that the interval between the last time this
operation was performed and now does not exceed the new interval due. If it does, perform the operation
at next aircraft inspection unless otherwise specified in this document.
7. MAINTENANCE OF SAFETY EQUIPMENT

The maintenance of safety equipment (life jackets, life rafts and survival equipment, etc.) is to be performed
in accordance with the regulations of the country in which the aircraft is registered. Most of these items of
equipment constitute "non standard" options which vary according to the type of interior furnishing. Some of
these items can be listed on the section 05-20 but if not refer to SMM.
Effectivity: ALL
05-20-00
page 3 / 4
FALCON 900EX EASY
8. TEFLON HOSES
All aircraft hoses are made of Teflon. Teflon hoses have no life limit.
Effectivity: ALL
05-20-00
page 4 / 4
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
21-20 DISTRIBUTION
RESTORATION OF THE FLOW

21-20-01-350-801-01 L501HN - LH FLOW
LIMITERS (OVERHAUL) - LH FLOW 4500 FH P/N 2742A020100 (1)
[212041] LIMITER (L501HN) LIMITER
RESTORATION OF THE FLOW
21-20-01-350-801-02 R501HN - RH FLOW
LIMITERS (OVERHAUL) - RH FLOW 4500 FH P/N 2742A020100 (1)
[212042] LIMITER (R501HN) LIMITER
RESTORATION OF THE NOSE CONE

21-31-09-350-801-01 VENTILATION FAN (REPLACEMENT 3HQ - NOSE CONE P/N 011479501 or
3000 FH (1)
[212081] OF BEARINGS) - NOSE CONE FAN FAN P/N 011479502
(3HQ)
INSPECTION / CHECK OF THE P/N 2097N010700 or
4HP -
21-32-06-200-801-01 ELECTROPNEUMATIC AND P/N 2097N020700 or
1500 FH ELECTROPNEUMATIC
21-314 [213141] PNEUMATIC VALVES - CLEANING OF P/N 2097N030700 or
ELECTROPNEUMATIC VALVE VALVE
P/N 2097N040801
INSPECTION / CHECK OF THE P/N 2099P010700 or
21-32-06-200-801-02 ELECTROPNEUMATIC AND 5HP - PNEUMATIC P/N 2099P020700 or
1500 FH
21-314 [213142] PNEUMATIC VALVES - CLEANING OF VALVE P/N 2099P030700 or
PNEUMATIC VALVE P/N 2099P040801
Effectivity: ALL
page 1 / 3
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
For valves having
already
INSPECTION / CHECK OF THE P/N 2097N010700 or undergone
ELECTROPNEUMATIC AND 4HP -
21-32-06-200-801-03 P/N 2097N020700 or cleaning, the
PNEUMATIC VALVES - CHECK OF 1500 FH ELECTROPNEUMATIC
21-314 [213143] OVERPRESSURE TIGHTNESS OF P/N 2097N030700 or overpressure
VALVE
ELECTROPNEUMATIC VALVE P/N 2097N040801 check is due at
the next 1500FH.
See 5-40
For valves having
already
INSPECTION / CHECK OF THE P/N 2099P010700 or undergone
ELECTROPNEUMATIC AND
21-32-06-200-801-04 5HP - PNEUMATIC P/N 2099P020700 or cleaning, the
PNEUMATIC VALVES - CHECK OF 1500 FH
21-314 [213144] OVERPRESSURE TIGHTNESS OF VALVE P/N 2099P030700 or overpressure
PNEUMATIC VALVE P/N 2099P040801 check is due at
the next 1500FH.
See 5-40
INSPECTION / CHECK OF THE
ELECTROPNEUMATIC AND 975HP - PNEUMATIC
21-32-06-200-801-05 P/N FGFB722404180 or See 5-40
PNEUMATIC VALVES - CHECK OF 7500 FH VALVE VACUUM
21-314 [213145] OVERPRESSURE RELIEF VALVE P/N FGFB722404190 No tolerance
SUPPLY LINE
VACUUM SUPPLY LINES
FUNCTIONAL TEST OF THE P/N 2097N010700 or
4HP -
21-32-06-720-801-01 ELECTROPNEUMATIC AND P/N 2097N020700 or (1)
4500 FH ELECTROPNEUMATIC
[213121] PNEUMATIC VALVES - P/N 2097N030700 or See 5-40
ELECTROPNEUMATIC VALVE (4HP) VALVE
P/N 2097N040801
FUNCTIONAL TEST OF THE P/N 2099P010700 or
21-32-06-720-801-02 ELECTROPNEUMATIC AND 5HP - PNEUMATIC P/N 2099P020700 or (1)
4500 FH
[213122] PNEUMATIC VALVES - PNEUMATIC VALVE P/N 2099P030700 or See 5-40
VALVE (5HP) P/N 2099P040801
Effectivity: ALL
page 2 / 3
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
FUNCTIONAL TEST OF THE BAGGAGE L508HP - LH
COMPARTMENT NEGATIVE
21-32-37-720-801-01 NEGATIVE
PRESSURE RELIEF VALVES - LH 4000 FH P/N 2827A01 (1)
[213181] NEGATIVE PRESSURE RELIEF VALVE PRESSURE RELIEF
(L508HP) VALVE
FUNCTIONAL TEST OF THE BAGGAGE R508HP - RH
COMPARTMENT NEGATIVE
21-32-37-720-801-02 NEGATIVE
PRESSURE RELIEF VALVES - RH 4000 FH P/N 2827A01 (1)
[213182] NEGATIVE PRESSURE RELIEF VALVE PRESSURE RELIEF
(R508HP) VALVE
21-50 COOLING
RESTORATION OF THE
21-52-05-350-801-01 504HN - P/N 3269B0102 or
TURBOCOOLER (OVERHAUL) - 3000 FH (1)
[215021] TURBOCOOLER (504HN) TURBOCOOLER P/N 3269B0202
P/N TVT107-28H or
P/N TVT107-28H1 or
21-52-21-350-801-01 RESTORATION OF THE TURBOFAN
3000 LDG 23HN - TURBOFAN P/N TVT107-28H2 or (1)
[215091] (OVERHAUL) - TURBOFAN (23HN)
P/N TVT107-28H3 or
P/N TVT107-28H4
21-70 MOISTURE / AIR CONTAMINANT CONTROL
RESTORATION OF THE OZONE

P/N 20425-1 or
21-71-01-350-801-01 CONVERTERS (FUNCTIONAL TEST L517HN - LH OZONE
5000 FH P/N D20425-1 or (1)
[361021] AND CLEANING) - LH OZONE CONVERTER
CONVERTER (L517HN) P/N MHD101
RESTORATION OF THE OZONE
P/N 20425-1 or
21-71-01-350-801-02 CONVERTERS (FUNCTIONAL TEST R517HN - RH OZONE
5000 FH P/N D20425-1 or (1)
[361022] AND CLEANING) - RH OZONE CONVERTER
CONVERTER (R517HN) P/N MHD101
Effectivity: ALL
page 3 / 3
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
24-30 DC GENERATION
P/N 8060-140 or
L1PA - ENGINE 1 P/N 8060-140-1 or
900 FH STARTER- P/N 8060-141 or (1)
RESTORATION OF THE STARTER-
24-31-13-350-801-01 GENERATOR P/N 8060-141-1 or
GENERATORS (OVERHAUL) - ENGINE
[243091] 1 STARTER-GENERATOR (L1PA)
P/N 8060-150
L1PA - ENGINE 1
1200 FH STARTER- P/N 8060-160 (1)
GENERATOR
P/N 8060-140 or
M1PA - ENGINE 2 P/N 8060-140-1 or
900 FH STARTER- P/N 8060-141 or (1)
24-31-13-350-801-02 GENERATOR P/N 8060-141-1 or
[243092] 2 STARTER-GENERATOR (M1PA)
P/N 8060-150
M1PA - ENGINE 2
1200 FH STARTER- P/N 8060-160 (1)
GENERATOR
P/N 8060-140 or
R1PA - ENGINE 3 P/N 8060-140-1 or
900 FH STARTER- P/N 8060-141 or (1)
24-31-13-350-801-03 GENERATOR P/N 8060-141-1 or
[243093] 3 STARTER-GENERATOR (R1PA)
P/N 8060-150
R1PA - ENGINE 3
1200 FH STARTER- P/N 8060-160 (1)
GENERATOR
Effectivity: ALL
page 1 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
P/N 8060-140 or
P/N 8060-140-1 or
21PA - APU STARTER-
RESTORATION OF THE STARTER- 900 APU-H P/N 8060-141 or (1)
24-31-13-350-801-04 GENERATOR
GENERATORS (OVERHAUL) - APU P/N 8060-141-1 or
[243094] STARTER-GENERATOR (21PA) P/N 8060-150
21PA - APU STARTER-
1200 APU-H P/N 8060-160 (1)
GENERATOR
Must be performed
L1PA - ENGINE 1
not earlier than 450
STARTER- P/N 8060-150
CHECK OF THE ENGINE AND APU FH and not later than
GENERATOR
24-31-17-220-801-01 STARTER-GENERATOR BRUSHES - 480 FH
24-330 [243301] ENGINE 1 STARTER-GENERATOR Must be performed
(L1PA) L1PA - ENGINE 1
FH and not later than
GENERATOR
630 FH
Must be performed
M1PA - ENGINE 2
GENERATOR
(M1PA) M1PA - ENGINE 2
GENERATOR
630 FH
Effectivity: ALL
page 2 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
Must be performed
R1PA - ENGINE 3
GENERATOR
(R1PA) R1PA - ENGINE 3
GENERATOR
630 FH
Must be performed
not earlier than 450 21PA - APU STARTER-
P/N 8060-150
APU-H and not later GENERATOR
CHECK OF THE ENGINE AND APU
24-31-17-220-801-04 than 480 APU-H
STARTER-GENERATOR BRUSHES -
24-330 [243304] APU STARTER-GENERATOR (21PA) Must be performed
not earlier than 600 21PA - APU STARTER-
P/N 8060-160
APU-H and not later GENERATOR
than 630 APU-H
CHECK / REPLACEMENT OF P/N 8060-140 or
L1PA - ENGINE 1
24-31-17-220-802-01 STARTER-GENERATOR BRUSHES - 300 FH then every P/N 8060-140-1 or
STARTER-
24-308 [243081] ENGINE 1 STARTER-GENERATOR 150 FH P/N 8060-141 or
(L1PA) GENERATOR
P/N 8060-141-1
M1PA - ENGINE 2
STARTER-
(M1PA) GENERATOR
P/N 8060-141-1
R1PA - ENGINE 3
STARTER-
(R1PA) GENERATOR
P/N 8060-141-1
Effectivity: ALL
page 3 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
P/N 8060-140 or
CHECK / REPLACEMENT OF
24-31-17-220-802-04 300 APU-H then 21PA - APU STARTER- P/N 8060-140-1 or
STARTER-GENERATOR BRUSHES -
24-308 [243084] APU STARTER-GENERATOR (21PA) every 150 APU-H GENERATOR P/N 8060-141 or
P/N 8060-141-1
RESTORATION OF A MAIN NICKEL- 24 M + 2 M L1PE - BATTERY 1 P/N 405CH10
24-32-01-350-801-01
CADMIUM BATTERY (OVERHAUL) -
24-351 [243511] BATTERY 1 (L1PE) 12 M + 1 M L1PE - BATTERY 1 P/N 4076-10
RESTORATION OF A MAIN NICKEL- 24 M + 2 M R1PE - BATTERY 2 P/N 405CH10
24-32-01-350-801-02
CADMIUM BATTERY (OVERHAUL) -
24-351 [243512] BATTERY 2 (R1PE) 12 M + 1 M R1PE - BATTERY 2 P/N 4076-10
(850 FH + 85 FH) or
REGULAR CHECK OF A MAIN NICKEL- L1PE - BATTERY 1 P/N 405CH10
24-32-01-700-801-01 (12 M + 10 %)
CADMIUM BATTERY - BATTERY 1
24-350 [243501] (L1PE) (250 FH + 25 FH) or
L1PE - BATTERY 1 P/N 4076-10
(6 M + 10 %)
(850 FH + 85 FH) or
REGULAR CHECK OF A MAIN NICKEL- R1PE - BATTERY 2 P/N 405CH10
24-32-01-700-801-02 (12 M + 10 %)
CADMIUM BATTERY - BATTERY 2
24-350 [243502] (R1PE) (250 FH + 25 FH) or
R1PE - BATTERY 2 P/N 4076-10
(6 M + 10 %)
(600 FH or 12 M)
24-32-01-700-802-01 REGULAR CHECK OF A MAIN LEAD / then every ((200 FH
L1PE - BATTERY 1 P/N RG380E/44LS
24-352 [243521] ACID BATTERY - BATTERY 1 (L1PE) + 40 FH) or (3 M + 18
D))
(600 FH or 12 M)
24-32-01-700-802-02 REGULAR CHECK OF A MAIN LEAD / then every ((200 FH
R1PE - BATTERY 2 P/N RG380E/44LS
24-352 [243522] ACID BATTERY - BATTERY 2 (R1PE) + 40 FH) or (3 M + 18
D))
24-32-01-960-801-01 DISCARD OF THE MAIN LEAD / ACID
1800 FH or 3 Y L1PE - BATTERY 1 P/N RG380E/44LS (3)
24-354 [243541] BATTERIES - BATTERY 1 (L1PE)
24-32-01-960-801-02 DISCARD OF THE MAIN LEAD / ACID
1800 FH or 3 Y R1PE - BATTERY 2 P/N RG380E/44LS (3)
24-354 [243542] BATTERIES - BATTERY 2 (R1PE)
Effectivity: ALL
page 4 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
SERVICING OF "SAFT" NICKEL-
24-32-09-610-801-01 4FG - STAND-BY P/N 785229 or
CADMIUM STAND-BY BATTERIES - 1 Y + 10 %
24-333 [243331] STAND-BY HORIZON BATTERY (4FG) HORIZON BATTERY P/N 804749
24-32-09-610-801-02 L36FQ - MAU 1 P/N 800864 or
24-333 [243332] MAU 1 BATTERY (L36FQ) BATTERY P/N 804745
24-32-09-610-801-03 R36FQ - MAU 2 P/N 800864 or
24-333 [243333] MAU 2 BATTERY (R36FQ) BATTERY P/N 804745
24-32-09-610-801-04 P/N 800864 or
CADMIUM STAND-BY BATTERIES - DU 1 Y + 10 % 35FV - DU 1 BATTERY
24-333 [243334] 1 BATTERY (35FV) P/N 804745
24-32-09-610-801-05 P/N 800864 or
CADMIUM STAND-BY BATTERIES - DU 1 Y + 10 % 36FV - DU 2 BATTERY
24-333 [243335] 2 BATTERY (36FV) P/N 804745
OPERATIONAL TEST OF
24-32-09-710-802-01 "SECURAPLANE" XL245 TYPE STAND- 4FG - STAND-BY
1Y P/N 100-0540-04
24-335 [243351] BY BATTERIES - STAND-BY HORIZON HORIZON BATTERY
BATTERY (4FG)
OPERATIONAL TEST OF
24-32-09-710-802-02 "SECURAPLANE" XL245 TYPE STAND- L36FQ - MAU 1
1Y P/N 100-0540-06
24-335 [243352] BY BATTERIES - MAU 1 BATTERY BATTERY
(L36FQ)
OPERATIONAL TEST OF
24-32-09-710-802-03 "SECURAPLANE" XL245 TYPE STAND- R36FQ - MAU 2
1Y P/N 100-0540-06
24-335 [243353] BY BATTERIES - MAU 2 BATTERY BATTERY
(R36FQ)
OPERATIONAL TEST OF
24-32-09-710-802-04
"SECURAPLANE" XL245 TYPE STAND- 1Y 35FV - DU 1 BATTERY P/N 100-0540-06
24-335 [243354] BY BATTERIES - DU 1 BATTERY (35FV)
OPERATIONAL TEST OF
24-32-09-710-802-05
"SECURAPLANE" XL245 TYPE STAND- 1Y 36FV - DU 2 BATTERY P/N 100-0540-06
24-335 [243355] BY BATTERIES - DU 2 BATTERY (36FV)
Effectivity: ALL
page 5 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
DISCARD OF "SECURAPLANE" XL245
24-32-09-960-802-01 4FG - STAND-BY
STAND-BY BATTERIES - STAND-BY 4Y P/N 100-0540-04 (4)
[243361] HORIZON BATTERY (4FG) HORIZON BATTERY
24-32-09-960-802-02 L36FQ - MAU 1
STAND-BY BATTERIES - MAU 1 4Y P/N 100-0540-06 (4)
[243362] BATTERY (L36FQ) BATTERY
24-32-09-960-802-03 R36FQ - MAU 2
STAND-BY BATTERIES - MAU 2 4Y P/N 100-0540-06 (4)
[243363] BATTERY (R36FQ) BATTERY
24-32-09-960-802-04
STAND-BY BATTERIES - DU 1 4Y 35FV - DU 1 BATTERY P/N 100-0540-06 (4)
[243364] BATTERY (35FV)
24-32-09-960-802-05
STAND-BY BATTERIES - DU 2 4Y 36FV - DU 2 BATTERY P/N 100-0540-06 (4)
[243365] BATTERY (36FV)
Effectivity: ALL
page 6 / 6
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
25-60 EMERGENCY EQUIPMENT
DISCARD OF THE ELT BATTERY PACK 32RC - EMERGENCY

25-61-13-960-802-01
(ADT 406) - EMERGENCY LOCATOR 5Y LOCATOR P/N 01N65900 (1) - (5)
[256071] TRANSMITTER (32RC) TRANSMITTER
At expiration date P/N ELT90A2560XXX
written on unit or or
DISCARD OF THE ELT BATTERY
after 48 hours of 32RC - EMERGENCY P/N ELT91A2560XXX
25-61-13-960-803-01 PACKS (ELT 90 / 91 OR ELT 96 / 97) -
continuous operating LOCATOR or
[256021] EMERGENCY LOCATOR
TRANSMITTER (32RC) or after a few hours TRANSMITTER P/N ELT96A2560XXX
of intermittent or
operating P/N ELT97A2560XXX
FUNCTIONAL TEST OF THE FDR / CVR
900RK - CVR P/N DK100 or
25-62-01-720-801-01 UNDERWATER LOCATOR BEACONS -
2Y UNDERWATER P/N DK120 or No tolerance
25-630 [256301] CVR UNDERWATER LOCATOR
BEACON (900RK) LOCATOR BEACON P/N ELP-362D
FUNCTIONAL TEST OF THE FDR / CVR
900FZ - FDR P/N DK100 or
25-62-01-720-801-02 UNDERWATER LOCATOR BEACONS -
2Y UNDERWATER P/N DK120 or No tolerance
25-630 [256302] FDR UNDERWATER LOCATOR
BEACON (900FZ) LOCATOR BEACON P/N ELP-362D
DISCARD OF THE BATTERY OF THE
900RK - CVR P/N DK100 or
25-62-05-960-801-01 FDR / CVR UNDERWATER LOCATOR 6 Y or at expiration
UNDERWATER P/N DK120 or
[256311] BEACONS - CVR UNDERWATER date written on unit
LOCATOR BEACON (900RK) LOCATOR BEACON P/N ELP-362D
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
DISCARD OF THE BATTERY OF THE
900FZ - FDR P/N DK100 or
25-62-05-960-801-02 FDR / CVR UNDERWATER LOCATOR 6 Y or at expiration
UNDERWATER P/N DK120 or
[256312] BEACONS - FDR UNDERWATER date written on unit
LOCATOR BEACON (900FZ) LOCATOR BEACON P/N ELP-362D
25-64-17-200-802-01 INSPECTION OF THE CREW LIFE 10ME - CREW LIFE
5Y P/N 63600-505
[256101] VESTS VESTS
25-64-17-200-803-01 INSPECTION OF THE PASSENGER 11ME - PASSENGER
5Y P/N 63600-105
[256201] LIFE VESTS LIFE VESTS
25-64-17-350-802-01 RESTORATION OF THE CREW LIFE 10ME - CREW LIFE
10 Y P/N 63600-505 (1)
[256102] VESTS (OVERHAUL OR DISCARD) VESTS
RESTORATION OF THE PASSENGER
25-64-17-350-803-01 11ME - PASSENGER
LIFE VESTS (OVERHAUL OR 10 Y P/N 63600-105 (1)
[256202] DISCARD) LIFE VESTS
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
26-10 DETECTION
Can be
26-10-00-720-801-01 L2WG - ENGINE 1 FIRE performed at an
PNEUMATIC FIRE DETECTORS - 6Y P/N 36017090040013
26-101 [261011] ENGINE 1 FIRE DETECTOR (L2WG) DETECTOR engine removal
prior to 6 years
Can be
26-10-00-720-801-02 M2WG - ENGINE 2 performed at an
26-101 [261012] ENGINE 2 FIRE DETECTOR (M2WG) FIRE DETECTOR engine removal
prior to 6 years
Can be
26-10-00-720-801-03 R2WG - ENGINE 3 performed at an
26-101 [261013] ENGINE 3 FIRE DETECTOR (R2WG) FIRE DETECTOR engine removal
prior to 6 years
Can be
26-10-00-720-801-04 9WG - APU FIRE performed at an
PNEUMATIC FIRE DETECTORS - APU 6 Y P/N 36018190040009
26-101 [261014] FIRE DETECTOR (9WG) DETECTOR APU removal
prior to 6 years
Effectivity: ALL
page 1 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
26-20 EXTINGUISHING
504WB - APU,
BAGGAGE
1Y+1M P/N 861630
WEIGHING OF THE FIRE COMPARTMENT FIRE
26-20-09-220-801-01 EXTINGUISHERS - APU, BAGGAGE EXTINGUISHER
26-204 [262041] COMPARTMENT FIRE EXTINGUISHER 504WB - APU,
(504WB) BAGGAGE P/N 863470-00 or
18 M
COMPARTMENT FIRE P/N 863470-01
EXTINGUISHER
505WB - ENGINE 1
FIRST-SHOOT,
1Y+1M ENGINE 2 SECOND- P/N 861630
WEIGHING OF THE FIRE SHOOT FIRE
26-20-09-220-801-02 EXTINGUISHERS - ENGINE 1 FIRST- EXTINGUISHER
26-204 [262042] SHOOT, ENGINE 2 SECOND-SHOOT 505WB - ENGINE 1
FIRE EXTINGUISHER (505WB) FIRST-SHOOT,
P/N 863470-00 or
18 M ENGINE 2 SECOND-
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
Effectivity: ALL
page 2 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
506WB - ENGINE 2
FIRST-SHOOT,
P/N 863470-00 or
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
508WB - ENGINE 3
FIRST-SHOOT,
P/N 863470-00 or
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
507WB - ENGINE 2
FIRST-SHOOT,
P/N 863470-00 or
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
Effectivity: ALL
page 3 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
503WB - MSC FIRE
WEIGHING OF THE FIRE 1Y+1M P/N 861630
26-20-09-220-801-06 EXTINGUISHER
EXTINGUISHERS - MSC FIRE
26-204 [262046] EXTINGUISHER (503WB) 503WB - MSC FIRE P/N 863470-00 or
18 M
EXTINGUISHER P/N 863470-01
504WB - APU,
RESTORATION OF THE FIRE BAGGAGE
5Y P/N 861630 (1) - No tolerance
EXTINGUISHERS (HYDROSTATIC COMPARTMENT FIRE
26-20-09-350-801-01 TEST AND PRESSURE GAGE EXTINGUISHER
[262121, 262071] CALIBRATION) - APU, BAGGAGE 504WB - APU,
COMPARTMENT FIRE EXTINGUISHER BAGGAGE P/N 863470-00 or
(504WB) 10 Y (1) - No tolerance
COMPARTMENT FIRE P/N 863470-01
EXTINGUISHER
505WB - ENGINE 1
FIRST-SHOOT,
RESTORATION OF THE FIRE 5Y ENGINE 2 SECOND- P/N 861630 (1) - No tolerance
EXTINGUISHERS (HYDROSTATIC SHOOT FIRE
[262122, 262072] CALIBRATION) - ENGINE 1 FIRST- 505WB - ENGINE 1
SHOOT, ENGINE 2 SECOND-SHOOT FIRST-SHOOT,
FIRE EXTINGUISHER (505WB) P/N 863470-00 or
10 Y ENGINE 2 SECOND- (1) - No tolerance
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
Effectivity: ALL
page 4 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
506WB - ENGINE 2
FIRST-SHOOT,
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
508WB - ENGINE 3
FIRST-SHOOT,
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
507WB - ENGINE 2
FIRST-SHOOT,
P/N 863470-01
SHOOT FIRE
EXTINGUISHER
Effectivity: ALL
page 5 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
RESTORATION OF THE FIRE 503WB - MSC FIRE
EXTINGUISHERS (HYDROSTATIC 5Y P/N 861630 (1) - No tolerance
26-20-09-350-801-06 EXTINGUISHER
TEST AND PRESSURE GAGE
[262126, 262076] CALIBRATION) - MSC FIRE 503WB - MSC FIRE P/N 863470-00 or
10 Y (1) - No tolerance
EXTINGUISHER (503WB) EXTINGUISHER P/N 863470-01
DISCARD OF THE ENGINE SHUTTLE
26-20-12-960-801-01 After each discharge L509WB - ENGINE 1
VALVES - ENGINE 1 SHUTTLE VALVE P/N 861585
[262171] (L509WB) of extinguisher SHUTTLE VALVE
26-20-12-960-801-02 After each discharge R509WB - ENGINE 3
VALVES - ENGINE 3 SHUTTLE VALVE P/N 861585
[262172] (R509WB) of extinguisher SHUTTLE VALVE
26-20-12-960-801-03 After each discharge M509WB1 - ENGINE 2
VALVES - ENGINE 2 LH SHUTTLE P/N 861585
[262173] VALVE (M509WB1) of extinguisher LH SHUTTLE VALVE
26-20-12-960-801-04 After each discharge M509WB2 - ENGINE 2
VALVES - ENGINE 2 RH SHUTTLE P/N 861585
[262174] VALVE (M509WB2) of extinguisher RH SHUTTLE VALVE
L3WB - ENGINE 1
FIRST-SHOOT
DISCARD OF THE FIRE 5Y P/N 861385 (6)
PERCUSSION
EXTINGUISHER PERCUSSION
26-20-13-960-801-01 CARTRIDGE
CARTRIDGES - ENGINE 1 FIRST-
[262052] SHOOT PERCUSSION CARTRIDGE L3WB - ENGINE 1
(L3WB) FIRST-SHOOT
10 Y P/N 862710-00 (6)
PERCUSSION
CARTRIDGE
Effectivity: ALL
page 6 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
R3WB - ENGINE 3
FIRST-SHOOT
PERCUSSION
26-20-13-960-801-02 CARTRIDGE
[262056] SHOOT PERCUSSION CARTRIDGE R3WB - ENGINE 3
(R3WB) FIRST-SHOOT
10 Y P/N 862710-00 (6)
PERCUSSION
CARTRIDGE
L4WB - ENGINE 2
SECOND-SHOOT LH
PERCUSSION
26-20-13-960-801-03 CARTRIDGE
CARTRIDGES - ENGINE 2 SECOND-
[262053] SHOOT LH PERCUSSION CARTRIDGE L4WB - ENGINE 2
(L4WB) SECOND-SHOOT LH
10 Y P/N 862700-00 (6)
PERCUSSION
CARTRIDGE
R4WB - ENGINE 2
SECOND-SHOOT RH
PERCUSSION
26-20-13-960-801-04 CARTRIDGE
[262057] SHOOT RH PERCUSSION CARTRIDGE R4WB - ENGINE 2
(R4WB) SECOND-SHOOT RH
10 Y P/N 862700-00 (6)
PERCUSSION
CARTRIDGE
Effectivity: ALL
page 7 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
L5WB - ENGINE 1
SECOND-SHOOT
PERCUSSION
26-20-13-960-801-05 CARTRIDGE
[262054] SHOOT PERCUSSION CARTRIDGE L5WB - ENGINE 1
(L5WB) SECOND-SHOOT
10 Y P/N 862700-00 (6)
PERCUSSION
CARTRIDGE
R5WB - ENGINE 3
SECOND-SHOOT
PERCUSSION
26-20-13-960-801-06 CARTRIDGE
[262058] SHOOT PERCUSSION CARTRIDGE R5WB - ENGINE 3
(R5WB) SECOND-SHOOT
10 Y P/N 862710-00 (6)
PERCUSSION
CARTRIDGE
L6WB - ENGINE 2
FIRST-SHOOT LH
PERCUSSION
26-20-13-960-801-07 CARTRIDGE
[262055] SHOOT LH PERCUSSION CARTRIDGE L6WB - ENGINE 2
(L6WB) FIRST-SHOOT LH
10 Y P/N 862700-00 (6)
PERCUSSION
CARTRIDGE
Effectivity: ALL
page 8 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
R6WB - ENGINE 2
FIRST-SHOOT RH
PERCUSSION
26-20-13-960-801-08 CARTRIDGE
[262051] SHOOT RH PERCUSSION CARTRIDGE R6WB - ENGINE 2
(R6WB) FIRST-SHOOT RH
10 Y P/N 862700-00 (6)
PERCUSSION
CARTRIDGE
22WB - APU
DISCARD OF THE FIRE 5Y PERCUSSION P/N 861375 (6)
26-20-13-960-801-09 EXTINGUISHER PERCUSSION CARTRIDGE
[252063] CARTRIDGES - APU PERCUSSION 22WB - APU
CARTRIDGE (22WB) 10 Y PERCUSSION P/N 862700-00 (6)
CARTRIDGE
9WB - BAGGAGE
COMPARTMENT
PERCUSSION
26-20-13-960-801-10 CARTRIDGE
CARTRIDGES - BAGGAGE
[262061] COMPARTMENT PERCUSSION 9WB - BAGGAGE
CARTRIDGE (9WB) COMPARTMENT
10 Y P/N 862710-00 (6)
PERCUSSION
CARTRIDGE
8WB - MSC
DISCARD OF THE FIRE 5Y PERCUSSION P/N 861375 (6)
26-20-13-960-801-11 EXTINGUISHER PERCUSSION CARTRIDGE
[262062] CARTRIDGES - MSC PERCUSSION 8WB - MSC
CARTRIDGE (8WB) 10 Y PERCUSSION P/N 862700-00 (6)
CARTRIDGE
Effectivity: ALL
page 9 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
WEIGHING OF THE PORTABLE FIRE
500WB - COCKPIT
26-20-15-720-801-01 EXTINGUISHERS - COCKPIT
18 M PORTABLE FIRE P/N 898052
26-210 [262101] PORTABLE FIRE EXTINGUISHER
(500WB) EXTINGUISHER
501WB - CABIN
26-20-15-720-801-02 EXTINGUISHERS - CABIN FRONT
18 M FRONT PORTABLE P/N 898052
(501WB) FIRE EXTINGUISHER
502WB - CABIN REAR
26-20-15-720-801-03 EXTINGUISHERS - CABIN REAR
18 M PORTABLE FIRE P/N 898052
(502WB) EXTINGUISHER
HYDROSTATIC TEST OF THE
500WB - COCKPIT
26-20-15-790-801-01 PORTABLE FIRE EXTINGUISHERS -
12 Y PORTABLE FIRE P/N 898052 (1)
[262091] COCKPIT PORTABLE FIRE
EXTINGUISHER (500WB) EXTINGUISHER
501WB - CABIN
12 Y FRONT PORTABLE P/N 898052 (1)
[262092] CABIN FRONT PORTABLE FIRE
EXTINGUISHER (501WB) FIRE EXTINGUISHER
502WB - CABIN REAR
12 Y PORTABLE FIRE P/N 898052 (1)
[262093] CABIN REAR PORTABLE FIRE
EXTINGUISHER (502WB) EXTINGUISHER
Effectivity: ALL
page 10 / 10
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
27-10 AILERONS AND SPOILERS
RESTORATION OF THE ROLL TRIM

27-14-01-350-801-01 13CC - ROLL TRIM
ACTUATOR (FUNCTIONAL TEST) - 12 Y P/N 021057-37 (1)
[271141] ROLL TRIM ACTUATOR (13CC) ACTUATOR
RESTORATION OF THE ROLL
EMERGENCY TRIM ACTUATOR 22CC - ROLL
27-14-03-350-801-01
(FUNCTIONAL TEST) - ROLL 12 Y EMERGENCY TRIM P/N 021127-01 (1)
[271161] EMERGENCY TRIM ACTUATOR ACTUATOR
(22CC)
RESTORATION OF THE ROLL MAIN
27-15-05-350-801-01 523CC - ROLL MAIN
AFU (FUNCTIONAL TEST / SERVICING) 12 Y P/N 105124 (1)
[271181] - ROLL MAIN AFU (523CC) AFU
27-15-07-350-801-01 L522CC - LH ROLL P/N 105045-06 or
AUXILIARY AFU (FUNCTIONAL TEST / 12 Y (1)
[271201] SERVICING) - LH ROLL AAFU (L522CC) AAFU P/N 105045-12
27-15-07-350-801-02 AUXILIARY AFU (FUNCTIONAL TEST / R522CC - RH ROLL P/N 105045-06 or
12 Y (1)
[271202] SERVICING) - RH ROLL AAFU AAFU P/N 105045-12
(R522CC)
27-20 RUDDER
RESTORATION OF THE RUDDER

(1)
27-22-01-350-801-01 SERVO-ACTUATOR (FUNCTIONAL 571CC - RUDDER P/N 103103-18 or
4000 FH No torelance
[272151, 272152] TEST) - RUDDER SERVO-ACTUATOR SERVO-ACTUATOR P/N 103103-19
(571CC) See 5-40
Effectivity: ALL
page 1 / 5
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
27-24-01-350-801-01 RESTORATION OF THE YAW TRIM 3CC - YAW TRIM
12 Y P/N 021057-36 (1)
[272141] ACTUATOR (FUNCTIONAL TEST) ACTUATOR
27-25-05-350-801-01 RESTORATION OF THE YAW MAIN 573CC - YAW MAIN
12 Y P/N 105125 (1)
[272101] AFU (FUNCTIONAL TEST / SERVICING) AFU
RESTORATION OF THE YAW
27-25-07-350-801-01
AUXILIARY AFU (FUNCTIONAL TEST / 12 Y 572CC - YAW AAFU P/N 105070-04 (1)
[272121] SERVICING) - YAW AAFU (572CC)
27-30 ELEVATORS
RESTORATION OF THE ELEVATOR

P/N 103129 or
27-32-01-350-801-01 SERVO-ACTUATOR (FUNCTIONAL 522CW - ELEVATOR (1)
10000 FH P/N 103144-04 or
[273171, 273172] TEST) - ELEVATOR SERVO- SERVO-ACTUATOR See 5-40
ACTUATOR (522CW) P/N 103144-06
RESTORATION OF THE PITCH MAIN
27-35-05-350-801-01 524CW - PITCH MAIN P/N 105122-02 or
AFU (FUNCTIONAL TEST / SERVICING) 12 Y (1)
[273141] - PITCH MAIN AFU (524CW) AFU P/N 105122-09
RESTORATION OF THE PITCH
27-35-07-350-802-01
AUXILIARY AFU (FUNCTIONAL TEST / 12 Y 523CW - PITCH AAFU P/N 105045-13 (1)
[273331] SERVICING) - PITCH AAFU (523CW)
P/N 021121-05 or
VISUAL CHECK OF THE HORIZONTAL P/N 021121-06 or
3CF - HORIZONTAL
27-40-01-210-802-01 STABILIZER ACTUATOR - P/N 021121-08 or
3750 FC or 6 Y STABILIZER
27-408 [274081] HORIZONTAL STABILIZER ELECTRIC P/N 021121-09 or
ACTUATOR (3CF) ELECTRIC ACTUATOR
P/N 021121-11 or
P/N 021121-12
Effectivity: ALL
page 2 / 5
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
P/N 021121-05 or
RESTORATION OF THE HORIZONTAL P/N 021121-06 or
3CF - HORIZONTAL
27-40-01-350-801-01 STABILIZER ACTUATOR (FULL P/N 021121-08 or
7500 FC or 12 Y STABILIZER (1)
[274091] DISASSEMBLY, INSPECTION AND P/N 021121-09 or
NDT) ELECTRIC ACTUATOR
P/N 021121-11 or
P/N 021121-12
27-50 FLAPS
RESTORATION OF THE FLAP SCREW L502CG - LH

27-53-01-350-801-01 (1)
JACKS (OVERHAUL) - LH OUTBOARD 4500 LDG OUTBOARD FLAP P/N 1-5319-3
[275151] FLAP SCREW JACK (L502CG) See 5-40
SCREW JACK
RESTORATION OF THE FLAP SCREW
L501CG - LH INBOARD
27-53-01-350-801-02 JACKS (OVERHAUL) - LH INBOARD (1)
3500 LDG FLAP LATERAL P/N 5318-3
[275152] FLAP LATERAL SCREW JACK See 5-40
(L501CG) SCREW JACK
RESTORATION OF THE FLAP SCREW L500CG - LH INBOARD
27-53-01-350-801-03 (1)
JACKS (OVERHAUL) - LH INBOARD 3500 LDG FLAP CENTER P/N 5318-3
[275153] FLAP CENTER SCREW JACK (L500CG) See 5-40
SCREW JACK
RESTORATION OF THE FLAP SCREW R500CG - RH
27-53-01-350-801-04 JACKS (OVERHAUL) - RH INBOARD INBOARD FLAP (1)
3500 LDG P/N 5318-3
[275154] FLAP CENTER SCREW JACK CENTER SCREW See 5-40
(R500CG) JACK
27-53-01-350-801-05 JACKS (OVERHAUL) - RH INBOARD INBOARD FLAP (1)
3500 LDG P/N 5318-3
[275155] FLAP LATERAL SCREW JACK LATERAL SCREW See 5-40
(R501CG) JACK
27-53-01-350-801-06 (1)
JACKS (OVERHAUL) - RH OUTBOARD 4500 LDG OUTBOARD FLAP P/N 2-5319-3
[275156] FLAP SCREW JACK (R502CG) See 5-40
SCREW JACK
Effectivity: ALL
page 3 / 5
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
CHECK OF THE SCREW / NUT PLAY
L502CG - LH
27-53-01-720-803-01 ON FLAP SCREW JACKS (AVIAC) - LH 3000 LDG then every No tolerance
OUTBOARD FLAP P/N 1-5319-3
27-514 [275141] OUTBOARD FLAP SCREW JACK 450 FH See 5-40
(L502CG) SCREW JACK
L501CG - LH INBOARD
FLAP LATERAL P/N 5318-3
27-514 [275142] INBOARD FLAP LATERAL SCREW 450 FH See 5-40
JACK (L501CG) SCREW JACK
L500CG - LH INBOARD
FLAP CENTER P/N 5318-3
27-514 [275143] INBOARD FLAP CENTER SCREW 450 FH See 5-40
JACK (L500CG) SCREW JACK
CHECK OF THE SCREW / NUT PLAY R500CG - RH
27-53-01-720-803-04 ON FLAP SCREW JACKS (AVIAC) - RH 3000 LDG then every INBOARD FLAP No tolerance
P/N 5318-3
27-514 [275144] INBOARD FLAP CENTER SCREW 450 FH CENTER SCREW See 5-40
JACK (R500CG) JACK
CHECK OF THE SCREW / NUT PLAY R501CG - RH
27-53-01-720-803-05 ON FLAP SCREW JACKS (AVIAC) - RH 3000 LDG then every INBOARD FLAP No tolerance
P/N 5318-3
27-514 [275145] INBOARD FLAP LATERAL SCREW 450 FH LATERAL SCREW See 5-40
JACK (R501CG) JACK
R502CG - RH
27-53-01-720-803-06 ON FLAP SCREW JACKS (AVIAC) - RH 3000 LDG then every No tolerance
OUTBOARD FLAP P/N 2-5319-3
27-514 [275146] OUTBOARD FLAP SCREW JACK 450 FH See 5-40
(R502CG) SCREW JACK
DISCARD OF THE FLAP SCREW L502CG - LH
27-53-01-960-801-01
JACKS - LH OUTBOARD FLAP SCREW 16000 LDG OUTBOARD FLAP P/N 1-5319-3
27-513 [275131] JACK (L502CG) SCREW JACK
DISCARD OF THE FLAP SCREW L501CG - LH INBOARD
27-53-01-960-801-02
JACKS - LH INBOARD FLAP LATERAL 15000 LDG FLAP LATERAL P/N 5318-3
27-513 [275132] SCREW JACK (L501CG) SCREW JACK
Effectivity: ALL
page 4 / 5
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
DISCARD OF THE FLAP SCREW L500CG - LH INBOARD
27-53-01-960-801-03
JACKS - LH INBOARD FLAP CENTER 15000 LDG FLAP CENTER P/N 5318-3
27-513 [275133] SCREW JACK (L500CG) SCREW JACK
R500CG - RH
DISCARD OF THE FLAP SCREW
27-53-01-960-801-04 INBOARD FLAP
JACKS - RH INBOARD FLAP CENTER 15000 LDG P/N 5318-3
27-513 [275134] SCREW JACK (R500CG) CENTER SCREW
JACK
R501CG - RH
DISCARD OF THE FLAP SCREW
27-53-01-960-801-05 INBOARD FLAP
JACKS - RH INBOARD FLAP LATERAL 15000 LDG P/N 5318-3
27-513 [275135] SCREW JACK (R501CG) LATERAL SCREW
JACK
DISCARD OF THE FLAP SCREW R502CG - RH
27-53-01-960-801-06
JACKS - RH OUTBOARD FLAP SCREW 16000 LDG OUTBOARD FLAP P/N 2-5319-3
27-513 [275136] JACK (R502CG) SCREW JACK
27-80 SLATS
RESTORATION OF THE OUTBOARD

27-80-01-350-801-01 L3CM - OUTBOARD
SLAT MANIFOLD (INSPECTION) - 12 Y P/N 108143-01 (1)
[278071] OUTBOARD SLAT MANIFOLD (L3CM) SLAT MANIFOLD
FUNCTIONAL TEST OF THE INBOARD
27-80-23-720-801-01 507CM - INBOARD
SLAT VALVE BOX - INBOARD SLAT 12 Y P/N 108117-06
27-810 [278101] VALVE BOX (507CM) SLAT VALVE BOX
Effectivity: ALL
page 5 / 5
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
28-20 DISTRIBUTION
FUNCTIONAL TEST OF THE BP

28-21-14-720-801-01 L32WB - BP 1
MANIFOLD THERMAL EXPANSION 10000 FH P/N L88A31-662-1 (1)
[283061] SYSTEMS - BP 1 MANIFOLD (L32WB) MANIFOLD
FUNCTIONAL TEST OF THE BP P/N L88A31-663 or
28-21-14-720-801-02 M32WB - BP 2
MANIFOLD THERMAL EXPANSION 10000 FH P/N L88A31-692 or (1)
[283062] SYSTEMS - BP 2 MANIFOLD (M32WB) MANIFOLD
P/N L88A31-695
FUNCTIONAL TEST OF THE BP
28-21-14-720-801-03 R32WB - BP 3
MANIFOLD THERMAL EXPANSION 10000 FH P/N L88A31-664-1 (1)
[283063] SYSTEMS - BP 3 MANIFOLD (R32WB) MANIFOLD
SEALING TEST OF THE NON-RETURN

28-70-05-790-801-01 VALVE OF THE PRESSURE REDUCER 500QD - PRESSURE
7500 FH P/N B14DE2080 (1)
[282101] - PRESSURE REDUCING VALVE REDUCING VALVE
(500QD)
RESTORATION OF THE VALVE BOXES
P/N B04BA1004 or
28-70-09-350-801-01 (FILTER CLEANING AND L507QD - LH VALVE
5000 FH P/N B04BA1005 or (1)
[282141] CALIBRATION CHECK) - LH VALVE BOX
BOX (L507QD) P/N B04BA1006
RESTORATION OF THE VALVE BOXES
P/N B04BA1004 or
28-70-09-350-801-02 (FILTER CLEANING AND R507QD - RH VALVE
5000 FH P/N B04BA1005 or (1)
[282142] CALIBRATION CHECK) - RH VALVE BOX
BOX (R507QD) P/N B04BA1006
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
FUNCTIONAL TEST OF THE WING L509QD - LH WING
P/N B06GA1050 or
28-70-13-720-801-01 TANK NEGATIVE PRESSURE RELIEF TANK NEGATIVE
5000 FH P/N B06GA1051 or (1)
[282061] VALVES - LH WING TANK NEGATIVE PRESSURE RELIEF
PRESSURE RELIEF VALVE (L509QD) P/N B06GA1052
VALVE
FUNCTIONAL TEST OF THE WING R509QD - RH WING
P/N B06GA1050 or
28-70-13-720-801-02 TANK NEGATIVE PRESSURE RELIEF TANK NEGATIVE
5000 FH P/N B06GA1051 or (1)
[282062] VALVES - RH WING TANK NEGATIVE PRESSURE RELIEF
PRESSURE RELIEF VALVE (R509QD) P/N B06GA1052
VALVE
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
29-10 PRIMARY HYDRAULIC POWER
RESTORATION OF THE HYDRAULIC

29-11-01-350-801-01 L500ML - HYDRAULIC P/N 42045 or
PUMPS (OVERHAUL) - HYDRAULIC 3000 FH (1)
[291071] PUMP 1 (L500ML) PUMP 1 P/N 4204501
29-11-01-350-801-02 M500ML - HYDRAULIC P/N 42045 or
[291072] PUMP 2 (M500ML) PUMP 2 P/N 4204501
29-11-01-350-801-03 R500ML - HYDRAULIC P/N 42045 or
[291073] PUMP 3 (R500ML) PUMP 3 P/N 4204501
DISCARD OF THE HYDRAULIC PUMP L2DW - HYDRAULIC
29-11-25-960-801-01
PRESSURE SWITCHES - HYDRAULIC 1240 FH PUMP 1 PRESSURE P/N 7G979
[291091] PUMP 1 PRESSURE SWITCH (L2DW) SWITCH
DISCARD OF THE HYDRAULIC PUMP M2DW - HYDRAULIC
29-11-25-960-801-02
[291092] PUMP 2 PRESSURE SWITCH (M2DW) SWITCH
DISCARD OF THE HYDRAULIC PUMP R2DW - HYDRAULIC
29-11-25-960-801-03
[291093] PUMP 3 PRESSURE SWITCH (R2DW) SWITCH
29-20 AUXILIARY HYDRAULIC POWER
CHECK OF THE STANDBY

29-20-03-220-801-01 3ML - STANDBY
ELECTRICAL PUMP MOTOR 5000 FH P/N 42032
29-203 [292031] BRUSHES ELECTRIC PUMP
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
29-20-03-720-801-01 FUNCTIONAL TEST OF THE STANDBY 3ML - STANDBY
5000 FH P/N 42032
29-202 [292021] ELECTRICAL PUMP MOTOR ELECTRIC PUMP
DISCARD OF THE STANDBY PUMP
L4ML - SYSTEM 1
29-20-07-960-801-01 PRESSURE SWITCHES - SYSTEM 1
1240 FH STANDBY PUMP P/N 7G978
[292041] STANDBY PUMP PRESSURE SWITCH
(L4ML) PRESSURE SWITCH
DISCARD OF THE STANDBY PUMP
R4ML - SYSTEM 2
29-20-07-960-801-02 PRESSURE SWITCHES - SYSTEM 2
1240 FH STANDBY PUMP P/N 7G978
[292042] STANDBY PUMP PRESSURE SWITCH
(R4ML) PRESSURE SWITCH
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
30-10 WING ANTI-ICING
FUNCTIONAL TEST OF THE SLAT

30-11-00-720-801-01 (2400 FH or 2000 L501HJ - LH INBOARD P/N 5036-400 or
TELESCOPIC DUCTS - LH INBOARD (8)
30-104 [301041] TELESCOPIC TUBE (L501HJ) FC) then every 1 Y TELESCOPIC TUBE P/N 5036-600
FUNCTIONAL TEST OF THE SLAT
30-11-00-720-801-02 (2400 FH or 2000 R501HJ - RH INBOARD P/N 5036-500 or
TELESCOPIC DUCTS - RH INBOARD (8)
30-104 [301042] TELESCOPIC TUBE (R501HJ) FC) then every 1 Y TELESCOPIC TUBE P/N 5036-700
FUNCTIONAL TEST OF THE SLAT L502HJ - LH
30-11-00-720-801-03 (2400 FH or 2000 P/N 5035-400 or
TELESCOPIC DUCTS - LH OUTBOARD OUTBOARD (8)
30-104 [301043] TELESCOPIC TUBE (L502HJ) FC) then every 1 Y P/N 5035-600
TELESCOPIC TUBE
FUNCTIONAL TEST OF THE SLAT R502HJ - RH
30-11-00-720-801-04 (2400 FH or 2000 P/N 5035-500 or
TELESCOPIC DUCTS - RH OUTBOARD OUTBOARD (8)
30-104 [301044] TELESCOPIC TUBE (R502HJ) FC) then every 1 Y P/N 5035-700
TELESCOPIC TUBE
30-20 ENGINE AIR INTAKE ANTI-ICING
FUNCTIONAL / SEALING TEST OF THE

L3HA - ENGINE 1 AIR
30-20-01-700-801-01 ENGINE AIR INTAKE ANTI-ICING
5000 FH INTAKE ANTI-ICING P/N 6911C020200 (1)
[302041] VALVES - ENGINE 1 AIR INTAKE ANTI-
ICING VALVE (L3HA) VALVE
M3HA - ENGINE 2 AIR
ICING VALVE (M3HA) VALVE
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
R3HA - ENGINE 3 AIR
ICING VALVE (R3HA) VALVE
30-40 WINDOWS, WINDSHIELDS AND DOORS
CHECK OF THE WINDSHIELD WIPER L5MK - LH

30-43-09-220-801-01
MOTOR BRUSHES - LH WINDSHIELD 15000 FH WINDSHIELD WIPER P/N 4267568
30-403 [304031] WIPER MOTOR (L5MK) MOTOR
CHECK OF THE WINDSHIELD WIPER R5MK - RH
30-43-09-220-801-02
MOTOR BRUSHES - RH WINDSHIELD 15000 FH WINDSHIELD WIPER P/N 4267575
30-403 [304032] WIPER MOTOR (R5MK) MOTOR
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
31-30 RECORDERS
15FZ - FDR
31-31-39-710-801-01 OPERATIONAL TEST OF THE FDR P/N 400-10B or
6Y ACCELERATION
31-306 [313061] ACCELERATION CONTACT P/N 400-10W
CONTACT
FUNCTIONAL TEST OF THE CVR 5RK - CVR
31-31-59-720-801-01 P/N 400-10B or
ACCELERATION CONTACT - CVR 6Y ACCELERATION
23-701 [237011] ACCELERATION CONTACT (5RK) P/N 400-10W
CONTACT
31-32-00-970-801-01 DOWNLOAD OF THE QUICK ACCESS Before the card P/N 200-001-001 or
42FZ - QAR (9)
31-931 [319311] RECORDER (QAR) - QAR (42FZ) capacity is full P/N 200-010-1010
REPLACEMENT OF THE QUICK 2Y 42FZ - QAR P/N 200-001-001
31-32-05-960-801-01
ACCESS RECORDER (QAR) BATTERY
31-934 [319341] - QAR BATTERY 10 Y 42FZ - QAR P/N 200-010-1010
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
32-10 MAIN LANDING GEARS (MLG) AND MLG DOORS
32-11-00-220-801-01 DETAILED INSPECTION OF THE MLG P/N D22801500 or Optional see note
6Y L2GF - LH MLG LEG
32-102 [321021] LEGS - LH MLG LEG (L2GF) P/N D22801500-X (10) - (11)
32-11-00-220-801-02 DETAILED INSPECTION OF THE MLG P/N D22802500 or Optional see note
6Y R2GF - RH MLG LEG
32-102 [321022] LEGS - RH MLG LEG (R2GF) P/N D22802500-X (10) - (11)
(1) - (10) - (11)
32-11-00-350-801-01 RESTORATION OF THE MLG LEGS P/N D22801500 or
6000 LDG or 10 Y L2GF - LH MLG LEG No tolerance for
[321051, 321053] (OVERHAUL) - LH MLG LEG (L2GF) P/N D22801500-X
landing limit
(1) - (10) - (11)
32-11-00-350-801-02 RESTORATION OF THE MLG LEGS P/N D22802500 or
6000 LDG or 10 Y R2GF - RH MLG LEG No tolerance for
[321052, 321054] (OVERHAUL) - RH MLG LEG (R2GF) P/N D22802500-X
landing limit
REPLACEMENT OF THE MLG LEGS
32-11-00-960-801-01 P/N D22801500 or
(DISCARD OF LIFE LIMITED PARTS) - 20000 LDG L2GF - LH MLG LEG See 5-40
[321031] LH MLG LEG (L2GF) P/N D22801500-X
REPLACEMENT OF THE MLG LEGS
32-11-00-960-801-02 P/N D22802500 or
(DISCARD OF LIFE LIMITED PARTS) - 20000 LDG R2GF - RH MLG LEG See 5-40
[321032] RH MLG LEG (R2GF) P/N D22802500-X
32-20 NOSE LANDING GEAR (NLG) AND NLG DOORS
32-21-00-220-801-01 DETAILED INSPECTION OF THE NLG P/N D22811500 or Optional see note
6Y 3GF - NLG LEG
32-202 [322021] LEG - NLG LEG (3GF) P/N D22811500-X (10) - (11)
(1) - (10) - (11)
32-21-00-350-801-01 RESTORATION OF THE NLG LEG P/N D22811500 or
6000 LDG or 10 Y 3GF - NLG LEG No tolerance for
[322051, 322052] (OVERHAUL) - NLG LEG (3GF) P/N D22811500-X
landing limit
Effectivity: ALL
page 1 / 4
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
REPLACEMENT OF THE NLG LEG
32-21-00-960-801-01 P/N D22811500 or
(DISCARD OF LIFE LIMITED PARTS) - 20000 LDG 3GF - NLG LEG See 5-40
[322031] NLG LEG (3GF) P/N D22811500-X
(1) - (10) - (11)
32-22-01-350-801-01 RESTORATION OF THE NLG DRAG 11GA - NLG DRAG P/N GA62269 or
6000 LDG or 10 Y No tolerance for
[322111] BRACE YOKE ASSY (OVERHAUL) BRACE P/N GA65181
landing limit
32-40 WHEELS AND BRAKES
Every three tire

changes until 15th L565GC - LH NLG After SB
P/N 5014199-1
and then every tire WHEEL F900EX-231
32-44-01-280-801-01 change
THE NLG WHEELS - LH NLG WHEEL
[324361] (L565GC) Every three tire Before SB
changes until 15th L565GC - LH NLG F900EX-231 -
P/N 5014199
and then every tire WHEEL Seal replacement
change before 400 LDG
Every three tire
changes until 15th R565GC - RH NLG After SB
P/N 5014199-1
and then every tire WHEEL F900EX-231
32-44-01-280-801-02 change
THE NLG WHEELS - RH NLG WHEEL
[324362] (R565GC) Every three tire Before SB
changes until 15th R565GC - RH NLG F900EX-231 -
P/N 5014199
and then every tire WHEEL Seal replacement
change before 400 LDG
Effectivity: ALL
page 2 / 4
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
At the 6th, 12th and (1)
L565GC - LH NLG
15th tire change then P/N 5014199-1 After SB
WHEEL
every 2 tire changes F900EX-231
RESTORATION OF THE NLG WHEELS
32-44-01-350-801-01 (1)
(OVERHAUL) - LH NLG WHEEL
[324491] (L565GC) At the 6th, 12th and Before SB
L565GC - LH NLG
15th tire change then P/N 5014199 F900EX-231 -
WHEEL
every 2 tire changes Seal replacement
before 400 LDG
At the 6th, 12th and (1)
R565GC - RH NLG
15th tire change then P/N 5014199-1 After SB
WHEEL
every 2 tire changes F900EX-231
RESTORATION OF THE NLG WHEELS
32-44-01-350-801-02 (1)
(OVERHAUL) - RH NLG WHEEL
[324492] (R565GC) At the 6th, 12th and Before SB
R565GC - RH NLG
15th tire change then P/N 5014199 F900EX-231 -
WHEEL
every 2 tire changes Seal replacement
before 400 LDG
Every three tire Do not exceed
32-44-09-280-801-01 changes until 15th L540GC - LH MLG 400 landings
THE MLG WHEELS - LH MLG P/N 5014197
[324323] OUTBOARD WHEEL (L540GC) and then every tire OUTBOARD WHEEL between 2 tire
change changes
32-44-09-280-801-02 changes until 15th L535GC - LH MLG 400 landings
THE MLG WHEELS - LH MLG INBOARD P/N 5014197
[324321] WHEEL (L535GC) and then every tire INBOARD WHEEL between 2 tire
change changes
32-44-09-280-801-03 changes until 15th R535GC - RH MLG 400 landings
THE MLG WHEELS - RH MLG INBOARD P/N 5014197
[324323] WHEEL (R535GC) and then every tire INBOARD WHEEL between 2 tire
change changes
Effectivity: ALL
page 3 / 4
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
32-44-09-280-801-04 changes until 15th R540GC - RH MLG 400 landings
THE MLG WHEELS - RH MLG P/N 5014197
[324324] OUTBOARD WHEEL (R540GC) and then every tire OUTBOARD WHEEL between 2 tire
change changes
RESTORATION OF THE MLG WHEELS At the 6th, 12th and
32-44-09-350-801-01 L540GC - LH MLG
(OVERHAUL) - LH MLG OUTBOARD 15th tire change then P/N 5014197 (1)
[324483] WHEEL (L540GC) OUTBOARD WHEEL
every 2 tire changes
32-44-09-350-801-02 L535GC - LH MLG
(OVERHAUL) - LH MLG INBOARD 15th tire change then P/N 5014197 (1)
[324481] WHEEL (L535GC) INBOARD WHEEL
32-44-09-350-801-03 R535GC - RH MLG
(OVERHAUL) - RH MLG INBOARD 15th tire change then P/N 5014197 (1)
[324482] WHEEL (R535GC) INBOARD WHEEL
32-44-09-350-801-04 R540GC - RH MLG
(OVERHAUL) - RH MLG OUTBOARD 15th tire change then P/N 5014197 (1)
[324484] WHEEL (R540GC) OUTBOARD WHEEL
Effectivity: ALL
page 4 / 4
FALCON 900EX EASY
05-20 CHAPTER 33 : LIGHTING
Scheduled
Component
Functional Index
task number
33-50 EMERGENCY LIGHTING

33-50-00-720-801-01
EMERGENCY LIGHTING SYSTEM - 12 M L3LW - EPS 1 P/N D734-02-001
33-501 [335011] EPS 1 (L3LW)
33-50-00-720-801-02
EMERGENCY LIGHTING SYSTEM - 12 M R3LW - EPS 2 P/N D734-02-001
33-501 [335012] EPS 2 (R3LW)
33-50-00-720-801-03
EMERGENCY LIGHTING SYSTEM - 12 M 4LW - EPS 3 P/N D734-02-001
33-501 [335013] EPS 3 (4LW)
Maintenance
SERVICING OF THE EMERGENCY Option 1 :
33-50-33-610-801-01 P/N D734-02-001 and
POWER SUPPLIES (PAGE) - EPS 1 1Y L3LW - EPS 1 Servicing every
33-504 [335041] (L3LW) Maintenance Option 1
year without life
limit
Maintenance
33-50-33-610-801-02 P/N D734-02-001 and
POWER SUPPLIES (PAGE) - EPS 2 1Y R3LW - EPS 2 Servicing every
33-504 [335042] (R3LW) Maintenance Option 1
year without life
limit
Maintenance
33-50-33-610-801-03 P/N D734-02-001 and
POWER SUPPLIES (PAGE) - EPS 3 1Y 4LW - EPS 3 Servicing every
33-504 [335043] (4LW) Maintenance Option 1
year without life
limit
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
Maintenance
DISCARD OF THE EPS BATTERY Option 2 : No
33-50-37-960-802-01 P/N D734-02-001 and
PACKS (PAGE) - EPS 1 (L3LW) 2Y L3LW - EPS 1 servicing required
[335051] BATTERY PACK Maintenance Option 2
but life limit every
2 years
Maintenance
33-50-37-960-802-02 P/N D734-02-001 and
PACKS (PAGE) - EPS 2 (R3LW) 2Y R3LW - EPS 2 servicing required
2 years
Maintenance
33-50-37-960-802-03 P/N D734-02-001 and
PACKS (PAGE) - EPS 3 (4LW) 2Y 4LW - EPS 3 servicing required
2 years
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
34-10 FLIGHT ENVIRONMENT DATA
34-10-00-720-801-01 FUNCTIONAL TEST OF THE AIR DATA P/N HG1153CA01 or Also RVSM
2Y L2FX - ADM 1
34-102 [341021] SYSTEM - ADM 1 P/N HG1153CA03 requirement
34-10-00-720-801-02 FUNCTIONAL TEST OF THE AIR DATA P/N HG1153CA01 or Also RVSM
2Y R2FX - ADM 2
34-102 [341022] SYSTEM - ADM 2 P/N HG1153CA03 requirement
34-20 ATTITUDE AND HEADING

SECONDARY FLIGHT DISPLAY (SFD)
34-23-00-720-801-01 P/N 27100-01-01 or
AND AIR DATA UNIT (ADU) - 2Y 15FG - ADU
34-004 [340041] FUNCTIONAL TEST OF AIR DATA UNIT P/N 27300-01-01
(ADU)
34-40 INDEPENDENT POSITION DETERMINING
CALIBRATION OF THE RADIO 2SA - RADIO

Only for CAT II and CAT
34-42-01-820-801-01 ALTIMETER RECEIVER / ALTIMETER 1
2Y III operation and with P/
34-413 [344131] TRANSMITTER - RADIO ALTIMETER 1 RECEIVER/
RECEIVER/TRANSMITTER (2SA) N 7001840-932
TRANSMITTER
CALIBRATION OF THE RADIO 22SA - RADIO
Only for CAT II and CAT
34-42-01-820-801-02 ALTIMETER RECEIVER / ALTIMETER 2
2Y III operation and with P/
34-413 [] TRANSMITTER - RADIO ALTIMETER 2 RECEIVER/
RECEIVER/TRANSMITTER (22SA) N 7001840-932
TRANSMITTER
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
34-50 DEPENDENT POSITION DETERMINING
Also RVSM
FUNCTIONAL TEST OF THE AIR
requirement
34-54-00-720-802-01 TRAFFIC CONTROL (ATC) SYSTEM L3SH - ATC XPDR 1 P/N 7517400-950 and
2Y Maintenance
34-533 [345331] USING TEST SET ATC-601 - ATC 1 MODULE Maintenance Option 1
SYSTEM Option 1 : Using
test set ATC-601
Also RVSM
requirement
34-54-00-720-802-02 TRAFFIC CONTROL (ATC) SYSTEM R3SH - ATC XPDR 2 P/N 7517400-950 and
2Y Maintenance
34-533 [345332] USING TEST SET ATC-601 - ATC 2 MODULE Maintenance Option 1
test set ATC-601
Also RVSM
requirement
34-54-00-720-803-01 TRAFFIC CONTROL (ATC) SYSTEM L3SH - ATC XPDR 1 P/N 7517400-950 and
2Y Maintenance
34-533 [345331] USING TEST SET IFR 6000 - ATC 1 MODULE Maintenance Option 2
test set IFR6000
Also RVSM
requirement
34-54-00-720-803-02 TRAFFIC CONTROL (ATC) SYSTEM R3SH - ATC XPDR 2 P/N 7517400-950 and
2Y Maintenance
34-533 [345332] USING TEST SET IFR 6000 - ATC 2 MODULE Maintenance Option 2
test set IFR6000
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
35-10 CREW OXYGEN SYSTEM
P/N MC10-12-100 or
RESTORATION OF THE CREW
35-10-05-350-801-01 L502WH - LH PILOT P/N MC10-12-101 or
OXYGEN MASKS (OVERHAUL) - LH 6Y (1) - (13)
[351041] PILOT OXYGEN MASK (L502WH) OXYGEN MASK P/N MC10-12-151 or
P/N MLD20-513
P/N MC10-12-100 or
35-10-05-350-801-02 R502WH - RH PILOT P/N MC10-12-101 or
OXYGEN MASKS (OVERHAUL) - RH 6Y (1) - (13)
[351042] PILOT OXYGEN MASK (R502WH) OXYGEN MASK P/N MC10-12-151 or
P/N MLD20-513
524WH - THIRD CREW
35-10-05-350-801-03 OXYGEN MASKS (OVERHAUL) - THIRD P/N MC10-12-151 or
6Y MEMBER OXYGEN (1) - (13)
[351043] CREW MEMBER OXYGEN MASK P/N MLD20-513
(524WH) MASK
P/N MC10-12-100 or
OPERATIONAL TEST OF THE CREW
35-10-05-710-801-01 L502WH - LH PILOT P/N MC10-12-101 or
OXYGEN MASKS - LH PILOT OXYGEN 1 Y
35-102 [351021] MASK (L502WH) OXYGEN MASK P/N MC10-12-151 or
P/N MLD20-513
P/N MC10-12-100 or
OPERATIONAL TEST OF THE CREW
35-10-05-710-801-02 R502WH - RH PILOT P/N MC10-12-101 or
OXYGEN MASKS - RH PILOT OXYGEN 1 Y
35-102 [351022] MASK (R502WH) OXYGEN MASK P/N MC10-12-151 or
P/N MLD20-513
OPERATIONAL TEST OF THE CREW 524WH - THIRD CREW
35-10-05-710-801-03 P/N MC10-12-151 or
OXYGEN MASKS - THIRD CREW 1Y MEMBER OXYGEN
35-102 [351023] MEMBER MASK (524WH) P/N MLD20-513
MASK
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
35-30 PORTABLE OXYGEN SYSTEM
35-30-01-960-801-01 508WH - EMERGENCY P/N 802300-14 or

DISCARD OF THE SMOKE HOOD 10 Y
[353001] BREATHING DEVICE P/N MR10035N
35-30-05-210-801-01 GENERAL VISUAL INSPECTION OF 537WH - OXYGEN
1Y P/N 894-20330
35-302 [353021] THE PORTABLE OXYGEN BOTTLE BOTTLE AND MASKS
35-30-05-350-801-01 RESTORATION OF THE PORTABLE 537WH - OXYGEN
5Y P/N 894-20330 (1)
[353101] OXYGEN BOTTLE (OVERHAUL) BOTTLE AND MASKS
35-30-09-100-801-01 CLEANING OF THE PORTABLE 537WH - OXYGEN
1 Y or after each use P/N 894-20330
35-301 [353011] OXYGEN MASKS BOTTLE AND MASKS
35-40 OXYGEN STORAGE SYSTEM
HYDROSTATIC TEST OF THE OXYGEN

35-40-01-790-801-01 500WH - OXYGEN P/N 176219-115 or (1)
CYLINDER - OXYGEN CYLINDER 5Y
[350021] (500WH) CYLINDER P/N 176220 No tolerance
35-40-01-960-801-01 DISCARD OF THE OXYGEN CYLINDER 500WH - OXYGEN P/N 176219-115 or
15 Y
[350041] - OXYGEN CYLINDER (500WH) CYLINDER P/N 176220
FUNCTIONAL TEST OF THE OXYGEN
35-40-05-720-801-01 500WH - OXYGEN P/N 176219-115 or
CYLINDER PRESSURE REDUCING 5Y No tolerance
35-003 [350031] VALVE CYLINDER P/N 176220
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
36-10 DISTRIBUTION / BLEED AIR
RESTORATION OF THE BLEED AIR

36-10-33-350-801-01 ARTICULATED PIPES (OVERHAUL) - L510HU - ENGINE 1
5000 FH P/N B45CB1120 (1)
[361091] ENGINE 1 ARTICULATED PIPE ARTICULATED PIPE
(L510HU)
RESTORATION OF THE BLEED AIR
36-10-33-350-801-02 ARTICULATED PIPES (OVERHAUL) - R510HU - ENGINE 3
5000 FH P/N B45CB1120 (1)
[361092] ENGINE 3 ARTICULATED PIPE ARTICULATED PIPE
(R510HU)
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
DISCARD OF THE PASSENGER DOOR (12)

902MC - PASSENGER
52-10-03-960-801-01 PNEUMATIC ACTUATOR - P/N 222900-1M03 or Life limit
5Y DOOR PNEUMATIC
[521321] PASSENGER DOOR PNEUMATIC P/N 222900M02 A/C 082 and
ACTUATOR (902MC) ACTUATOR
above
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
71-20 MOUNTS
Engine
SPECIAL DETAILED INSPECTION OF maintenance
L900EZ1 - ENGINE 1
71-20-05-230-801-01 THE ENGINE 1 AND 3 FRONT MOUNT manual During
3750 FC FRONT MOUNT P/N 3071070-4
[710091] INTERFACES - ENGINE 1 FRONT engine removal
MOUNT UPPER INTERFACE (L900EZ1) UPPER INTERFACE
for MPI/CZI prior
to 3750 FC
Engine
THE ENGINE 1 AND 3 FRONT MOUNT L900EZ2 - ENGINE 1
71-20-05-230-801-02 manual During
INTERFACES - ENGINE 1 FRONT 3750 FC FRONT MOUNT P/N 3071070-4
[710092] MOUNT LOWER INTERFACE engine removal
LOWER INTERFACE
(L900EZ2) for MPI/CZI prior
to 3750 FC
Engine
THE ENGINE 1 AND 3 FRONT MOUNT R900EZ1 - ENGINE 3
71-20-05-230-801-03 manual During
[710093] MOUNT UPPER INTERFACE engine removal
UPPER INTERFACE
(R900EZ1) for MPI/CZI prior
to 3750 FC
Engine
THE ENGINE 1 AND 3 FRONT MOUNT R900EZ2 - ENGINE 3
71-20-05-230-801-04 manual During
[710094] MOUNT LOWER INTERFACE engine removal
LOWER INTERFACE
(R900EZ2) for MPI/CZI prior
to 3750 FC
Effectivity: ALL
page 1 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
THE ENGINE 2 FRONT VIBRATION Can be
M900EZ1 - ENGINE 2
71-20-17-230-801-01 ISOLATORS / REPLACEMENT OF performed at an
5000 FH LH FRONT VIBRATION P/N LM833SA13
71-008 [710081] RUBBER CORES - LH FRONT engine 2 removal
VIBRATION ISOLATOR RUBBER CORE ISOLATOR
prior to 5000 FH
REPLACEMENT
M900EZ2 - ENGINE 2
5000 FH RH FRONT VIBRATION P/N LM833SA13
71-008 [710082] RUBBER CORES - RH FRONT engine 2 removal
VIBRATION ISOLATOR RUBBER CORE ISOLATOR
prior to 5000 FH
REPLACEMENT
M900EZ1 - ENGINE 2
5000 FH LH FRONT VIBRATION P/N LM833SA13
71-008 [710083] RUBBER CORES - LH FRONT engine 2 removal
VIBRATION ISOLATOR METALLIC ISOLATOR
prior to 5000 FH
PART INSPECTION
M900EZ2 - ENGINE 2
5000 FH RH FRONT VIBRATION P/N LM833SA13
71-008 [710084] RUBBER CORES - RH FRONT engine 2 removal
VIBRATION ISOLATOR METALLIC ISOLATOR
prior to 5000 FH
PART INSPECTION
Effectivity: ALL
page 2 / 2
FALCON 900EX EASY
Scheduled
Component
Functional Index
task number
78-30 THRUST REVERSER
P/N
78-31-01-250-801-01 FGFB583701100D3 or
THE THRUST REVERSER DOORS - LH 2000 FC 454FL - LH TR DOOR
78-310 [783101] CLOSE OUT FITTING P/N
FGFB583701200D3
P/N
78-31-01-250-801-02 FGFB583701100D3 or
THE THRUST REVERSER DOORS - RH 2000 FC 454FR - RH TR DOOR
78-310 [783102] CLOSE OUT FITTING P/N
FGFB583701200D3
P/N
78-31-01-250-801-03 FGFB583701100D3 or
THE THRUST REVERSER DOORS - LH 4000 FC 454FL - LH TR DOOR
78-310 [783103] BEAM AND FITTING P/N
FGFB583701200D3
P/N
78-31-01-250-801-04 FGFB583701100D3 or
THE THRUST REVERSER DOORS - RH 4000 FC 454FR - RH TR DOOR
78-310 [783104] BEAM AND FITTING P/N
FGFB583701200D3
Effectivity: ALL
page 1 / 1
FALCON 900EX EASY
05-50-00
UNSCHEDULED MAINTENANCE CHECKS
ATA 100 DESCRIPTION OF NOTE

MAINTENANCE OPERATIONS
PROCEDURE
05-50-00-100-801 CLEANING AFTER

(Refer to TASK ELECTROLYTE SPILLAGE
05-50-00-100-801)
24-315
05-50-00-200-801 CHECK AFTER A TOWING

(Refer to TASK INCIDENT
05-50-00-200-801)
09-101
05-50-00-200-802 CHECK AFTER HAILSTORM

(Refer to TASK
05-50-00-200-802)
51-002
05-50-00-200-803 CHECK AFTER A LIGHTNING

(Refer to TASK STRIKE
05-50-00-200-803)
51-001
05-50-00-200-804 CHECK AFTER A REJECTED

(Refer to TASK TAKE-OFF OR EMERGENCY
05-50-00-200-804) BRAKING
32-407
05-50-00-200-805 CHECK AFTER A FLIGHT IN

(Refer to TASK EXCESSIVE LOAD FACTOR
05-50-00-200-805)
51-000
05-50-00-200-809 INSPECTION AFTER SLAT To be performed after slats/flaps extension at more than Maximum
(Refer to TASK EXTENSION IN OVERSPEED speed for slats/flaps extension as defined in the Airplane Flight
05-50-00-200-809) CONDITION Manual (AFM).
57-505
05-50-00-200-810 INSPECTION AFTER FLAP To be performed after slats/flaps extension at more than Maximum
(Refer to TASK EXTENSION IN OVERSPEED speed for slats/flaps extension as defined in the Airplane Flight
05-50-00-200-810) CONDITION Manual (AFM).
57-605
05-50-00-620-803 SPECIFIC MAINTENANCE FOR If aircraft has been operated and parked under continuously
(Refer to TASK A/C OPERATING IN COLD freezing temperatures for more than 15 flights.
05-50-00-620-803) WEATHER
05-105
Effectivity: ALL
05-50-00
page 1 / 4
FALCON 900EX EASY

PROCEDURE
05-50-00-620-804 PROCEDURE FOR AIRCRAFT To be performed when A/C is operated or parked under freezing
(Refer to TASK PROLONGED OPERATION AT temperature for more than 300 flights hours or 6 months (first limit
05-50-00-620-804) LOW TEMPERATURES reached).
51-055
05-50-00-700-801 CHECK AND

(Refer to TASK DECONTAMINATION OF THE
05-50-00-700-801) AIR CONDITIONING SYSTEM
21-206 AFTER POLLUTION
05-50-00-700-803 CHECK AFTER FIRE Refer to 05-20-26 (shuttle valve replacement)

(Refer to TASK EXTINGUISHER PERCUSSION
05-50-00-700-803)
20-350
05-50-00-700-806 CHECK AFTER LANDING ON A

(Refer to TASK TAR-MACADAM RUNWAY IN
05-50-00-700-806) VERY HOT WEATHER
32-004
05-50-00-700-807 CHECK AFTER LANDING ON A

(Refer to TASK DRY AND DIRTY RUNWAY
05-50-00-700-807)
32-001
05-50-00-700-808 CHECK AFTER HARD / To be performed also after landing at weight beyond Maximum
(Refer to TASK OVERWEIGHT LANDING Landing Weight (MLW) with a vertical speed at touch down greater
05-50-00-700-808) than 360 ft/min.
32-000
05-50-00-730-801 CHECK AFTER INCIDENT ON

(Refer to TASK THE HYDRAULIC SYSTEM
05-50-00-730-801) 1 - Filter clogging
29-002 2 - Pump failure
05-50-00-910-801 AIRCRAFT CHECK FLIGHT A complete check flight is to be made following a C inspection or
(Refer to TASK multiple.
05-50-00-910-801) The complete check flight is made with respect of the relevant
05-500 authorities of the country in which the aircraft is registered.
09-10-00-910-810 DEBOGGING THE AIRCRAFT

(Refer to TASK
09-10-00-910-810)
09-300
10-10-00-200-801 CHECK AFTER PARKING OF

(Refer to TASK THE AIRCRAFT IN HIGH WIND
10-10-00-200-801) CONDITIONS
10-201
Effectivity: ALL
05-50-00
page 2 / 4
FALCON 900EX EASY

PROCEDURE
10-10-00-550-801 STORAGE AND REMOVAL Storage procedure is to be performed when the aircraft does not
(Refer to TASK FROM STORAGE fly for more than 65 days. During the 65 days without storage, the
10-10-00-550-801) daily servicing procedure (see Ground Servicing Manual) must be
20-355 performed at least once at the middle of the period. During
maintenance inspection or completion work period, storage of the
aircraft is not necessary, even if the period exceeds 65 days.
10-20-00-910-802 MOORING THE AIRCRAFT IN

(Refer to TASK CASE OF SNOWFALL
10-20-00-910-802)
10-101
20-30-00-330-801 TEMPORARY REPAIR AFTER

(Refer to TASK MINOR DAMAGE TO A
20-30-00-330-801) COMPOSITE MATERIAL
51-003 COMPONENT
20-31-00-140-801 AIRCRAFT EXTERIOR RINSING It is recommended to perform an aircraft rinsing at the first
(Refer to TASK available time:
20-31-00-140-801) • after flying at low level above sea (airport near the sea),
20-318 • if flight is performed after de-icing,
• after flying in volcanic ash.
20-31-00-910-801 GROUND DE-ICING AND

(Refer to TASK PREVENTIVE ANTI-ICING
20-31-00-910-801)
20-625
20-60-00-370-813 APPLICATION OF THE PAINT To be performed in case of complete paint renewal.

(Refer to TASK SCHEME ON COMPOSITE
20-60-00-370-813) COMPONENTS
20-615
27-50-00-640-803 CLEANING / GREASING OF THE To be performed after flying through sand or volcanic ash.
(Refer to TASK FLAP SCREW JACK
27-50-00-640-803) ACTUATING SCREWS
27-500
28-00-00-910-804 MEASURES TO BE TAKEN

(Refer to TASK AFTER MAINTENANCE
28-00-00-910-804) OPERATIONS IN THE FUEL
28-100 TANKS
28-21-17-790-801 SEALING TEST OF THE APU After each APU removal/installation.

(Refer to TASK FUEL SHUT-OFF VALVE
28-21-17-790-801)
49-001
Effectivity: ALL
05-50-00
page 3 / 4
FALCON 900EX EASY

PROCEDURE
32-32-00-700-801 CHECK AFTER LANDING GEAR

(Refer to TASK EMERGENCY EXTENSION
32-32-00-700-801)
32-002
34-11-01-200-801 CHECK OF THE TOTAL To be performed after flying through sand or volcanic ash.
(Refer to TASK PRESSURE PROBE DRAIN
34-11-01-200-801) HOLES FOR CLOGGING
34-107
53-10-00-220-801 DETAILED INSPECTION OF THE For RVSM requirements. To be performed in case of painting or
(Refer to TASK STATIC PRESSURE PROBE damage in RVSM area, except in case of flaked paint on rivet
53-10-00-220-801) AND OF THE FUSELAGE SKIN heads or locally around the edge of the static probe base.
53-026 IN PROBE AREA
71-00-00-910-802 ENGINE INSPECTION RUN-UP

(Refer to TASK
71-00-00-910-802)
71-003
71-00-00-910-803 END OF INSPECTION RUN-UP

(Refer to TASK
71-00-00-910-803)
71-002
Effectivity: ALL
05-50-00
page 4 / 4

MPD Falcon PDF

Uploaded by

Copyright:

Available Formats

MPD Falcon PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MPD Falcon PDF

Uploaded by

Copyright:

Available Formats

FALCON 900EX EASY

ORIGINAL EDITION MARCH 2011

Scheduled maintenance task number example

24-30-00-710-801 AMTOSS numbering

Scheduled maintenance task number examples

21-32-06-200-801-01 AMTOSS numbering

21-20-01-350-801-01 AMTOSS numbering

32-11-00-350-801-02 AMTOSS numbering

27-53-01-350-802-01 AMTOSS numbering of new task

2. CROSS PROCEDURE REFERENCE TABLE

00-00: MAINTENANCE PLANNING DOCUMENT

00-00-00: MAINTENANCE PLANNING DOCUMENT

05-00-03: LIST OF REVISIONS

05-00-05: INFORMATION TO OPERATORS

05-00-10: TABLE OF MODIFICATIONS

05-10: AIRCRAFT MAINTENANCE OPERATIONS

05-10-00: AIRCRAFT MAINTENANCE OPERATIONS

05-10 CHAPTER 21 : AIR CONDITIONING

05-10 CHAPTER 22 : AUTO FLIGHT

05-10 CHAPTER 23 : COMMUNICATIONS

05-10 CHAPTER 24 : ELECTRICAL POWER

05-10 CHAPTER 25 : EQUIPMENT / FURNISHINGS

05-10 CHAPTER 26 : FIRE PROTECTION

05-10 CHAPTER 27 : FLIGHT CONTROLS

05-10 CHAPTER 28 : FUEL

05-10 CHAPTER 29 : HYDRAULIC POWER

05-10 CHAPTER 30 : ICE AND RAIN PROTECTION

05-10 CHAPTER 31 : INDICATING - RECORDING SYSTEMS

05-10 CHAPTER 32 : LANDING GEAR

05-10 CHAPTER 34 : NAVIGATION

05-10 CHAPTER 35 : OXYGEN

05-10 CHAPTER 36 : PNEUMATIC

05-10 CHAPTER 38 : WATER - WASTE

05-10 CHAPTER 45 : CENTRAL MAINTENANCE SYSTEM (CMS)

05-10 CHAPTER 52 : DOORS

05-10 CHAPTER 53 : FUSELAGE

05-10 CHAPTER 54 : NACELLES AND PYLONS

05-10 CHAPTER 55 : STABILIZERS

05-10 CHAPTER 56 : WINDOWS

05-10 CHAPTER 57 : WINGS

05-10 CHAPTER 71 : POWER PLANT

05-10 CHAPTER 73 : ENGINE FUEL AND CONTROL

05-10 CHAPTER 76 : ENGINE CONTROLS

05-10 CHAPTER 77 : ENGINE INDICATING

05-10 CHAPTER 78 : EXHAUST

05-20: COMPONENT MAINTENANCE OPERATIONS

05-20-00: MAINTENANCE OF COMPONENTS, TIME BETWEEN

05-20 CHAPTER 21 : AIR CONDITIONING

05-20 CHAPTER 24 : ELECTRICAL POWER

05-20 CHAPTER 25 : EQUIPMENT / FURNISHINGS

05-20 CHAPTER 26 : FIRE PROTECTION

05-20 CHAPTER 27 : FLIGHT CONTROLS

05-28 CHAPTER 28 : FUEL

05-29 CHAPTER 29 : HYDRAULIC POWER

05-20 CHAPTER 31 : INDICATING - RECORDING SYSTEMS

05-20 CHAPTER 32 : LANDING GEAR

05-20 CHAPTER 33 : LIGHTING

05-20 CHAPTER 34 : NAVIGATION

05-20 CHAPTER 35 : OXYGEN