Here Is All You Wanted To Know About Draft Survey Calculations

Here Is All You Wanted to Know About
Draft Survey Calculations

Written by Capt Rajeev Jassal on March 10, 2017
Have you seen a truck weighing bridge ? Do you know how it works ?
It weighs the empty weight of the truck and then the loaded weight.
The difference is the weight of the cargo on that truck.
Well draft survey uses a similar principle to measure the cargo

loaded on board ships.
With draft survey we measures the initial weight (displacement) of the
ship and it measures the final weight (displacement) of the ship after
loading. The difference plus all the weights that were taken out (like
ballast) will be the cargo loaded.
The only difference between weight measurement in case of truck and
ship is that for later the calculation is not that simple.
So in this post I will discuss about how to go about measuring the

cargo quantity with draft survey.
1. Why Draft survey ?
On tankers, the measurement of cargo quantity loaded is simple. We

know the density of the cargo and we know the volume. It is easier to
know the weight of the cargo loaded.
But with cargoes like coal, we cannot measure the weight by just
measuring the the height of the hold to which cargo is loaded.
This is because unlike liquids, solid cargoes would not take the shape
of the hold.
Calculating the cargo loaded with draft survey is the most appropriate
way.
But it isn’t only with solid cargoes. Sometimes we have to measure the
cargo quantity of liquids by draft survey. One such cargo is Mollasses
loaded on chemical tankers.
This cargo has air in it and thus the density of this cargo is not
uniform. Calculating the way we calculate the weights for other liquids
will give wrong quantity. Draft survey is the answer in this case too.
So let us see how we need to go about draft survey.
2. Basics of Draft survey
With draft survey calculations, all we want to know is the difference in

ship’s arrival weight (Displacement) and departure weight
(displacement).
Let us say we have these figures
On Arrival
Displacement: 20000 T
Cargo: 0
Ballast: 6000 T
Other weights : 1000 T
On Departure
Displacement: 50000 T
Cargo: ???
Ballast: 500 T
Other weights : 1000 T
The difference in displacement is 30000 T. Out of this 5500 T of

ballast was removed and some cargo was loaded at the port.
It is simple calculation to know the quantity of the cargo loaded which

is 35500 T.
In this simple calculation, it is not difficult to know the ballast and fuel
on board. What we need to know is the displacement of the ship on
arrival and after completion of loading.
Once we know that, we can know the cargo quantity. The easiest way
to calculate the ship’s displacement is by noting down the draft of the
vessel and looking for the displacement for that draft in the trim and
stability booklet.
That is the simplest way of saying it but then there are few corrections
to this which we will discuss.
3. Draft of the vessel
There are two drafts for a vessel.
 Draft at forward and aft perpendiculars and at midship of these two.

This is the draft that is listed in the ship’s trim and stability booklet.
 Drafts at actual draft marks painted on ship side.
So to get the displacement from the trim and stability booklet, we

must get the drafts at the perpendiculars.
What we will get from the visual drafts will not be the drafts at
perpendiculars in most of the cases.
Exclusive Bonus: Download Excel Sheet of Draft Survey Calculation

Let us say we have the visual draft as follows. In draft survey
calculation we call the visual drafts as “Apparent drafts”.
So let us say that the mean of both side of the apparent drafts is
Forward = 6.43 m
Aft = 8.53 m
Midship = 7.42 m
Apparent Trim = 2.1 m
As I said we need to bring these drafts to the perpendiculars.
The formula for correction to the visuals drafts to bring it to the

perpendiculars is
You will find this distances in the Trim and stability book of the ship.
Have a look at these corrections for one of the ship.
As we can see that the distance from forward perpendicular to the
forward draft mark is 9.95 meters.
So the correction to the forward draft would be 9.95 x 2.10 / 155. This
will be equal to 0.135 meters. As the forward perpendiculr is forward
of the draft marks and we have stern trim, this correction will be
negative.
Same way for apparent trim of 2.10 meters, the corrections to the
apparent drafts are
So the drafts at forward and aft perpendiculars and midship will be
6.295 m / 8.653 m / 7.451 m respectively.
Ideally we should now take the midship draft (7.451 m in this case)
and look for the displacement from the trim and stability booklet.
But there can be errors in this drafts and we have to make sure that
draft is correct. These error could be
 Errors in reading few of the visual drafts
 Errors due to Hog or Sag of the vessel
To minimise these errors we finalise the draft of the vessel by having

mean of means draft. This is also called Quarter mean draft.
Mean of means is considered to be the accurate draft of the vessel at

the midship. This is the draft we need to enter in the trim and stability
booklet.
Below is the mean of means draft for our example.
4. Calculating displacement of the ship
Now that we know the draft of the ship, we can open the trim and
stability booklet and check the displacement for this draft.
We may have to interpolate to get the exact displacement.
Here is the relevant page of Trim and stability booklet for this ship.
So
the displacement for our draft of 7.45675 m will be 30702.28.
We have now got the displacement for the actual draft of th vessel. But
there will be few corrections to this displacement. Let us see what
these are.
5. 1st Trim correction
The draft and displacement we got so far is at the mean of aft and
forward perpendicular.
As per Archimedes principle, a floating ship displaces the amount of

water equal to its own weight. And the ship floats at the center of
floatation. So the correct displacement is the displacement
corresponding to the draft at the center of floatation and not at the
mean draft.
The correction applied to the displacement at mean draft to bring it to
the displacement at center of floatation is called the “1st Trim
correction”.
The formula for 1st trim correction is
If you wish to know how this formula arrived, watch this video
As we need the values of TPC and LCF for calculating 1st trim
correction, open the Trim & stability booklet and find these values for
the vessel’s draft. Again we have to do the interpolation to get the
exact values.
Now let us calculate the 1st Trim correction for our example.
In this case it comes out to be 65 T but it can have larger value in
other situations. This 1st trim correction we need to add to
the displacement we got earlier.
Sign of 1st trim correction

This is not so difficult to find. We have the draft at the Midship and we
are applying the correction for change in draft because LCF is not at
the midship.
Now let us say vessel has stern trim and LCF is aft of midship. Which
draft will be more ? The one read at the LCG or at the midship ?
You are right !!! The draft at the LCF will be more. So in this case the
correction need to be added to the midship displacement we have got.
So for sign of 1st trim correction, all we have to see is the location of
LCF with respect to Midship.
So for sign of 1st trim correction, all we have to see is the location of
LCF with respect to Midship. Then by pure logic, we can find out if we
need to add that correction or subtract.
6. 2nd Trim correction
Now there is this another correction. First trim correction was because
LCF was not at the midship. If the LCF was at the midship, there would
not be any 1st trim correction.
The distance of LCF from the midship is given in the trim and stability
booklet. For hydrostatic ship particulars for some ships, the value of
LCF is at zero trim condition. For example see below
Now if the vessel is trimmed, the position of LCF will change slightly
because of change in water plane of the ship.
2nd Trim correction takes care of this change of position of LCF

because of trim of the vessel.
The formula for 2nd trim correction is

To get the value of Dm-Dz, get the value of MCTC for (mean draft
+50 cms) and for (mean draft-50 cms). The difference between these
two values of MCTC will be the value for Dm-Dz.
With this value of Dm-Dz, we will get 2nd Trim correction as 35 T.
The 2nd trim correction is always positive.

But see the hydrosatic particulars of the vessel that I took the data
from. LCF values are given for different trims.
We can interpolate to get the LCF for actual trim of the vessel. In this
case 2nd trim correction will not be applicable.
7. Final Displacement
Once we have 1st trim correction and 2nd trim correction, we need to
apply these to the ship’s displacement.
So the actual displacement with respect to the draft at LCF will be
Displacement at Midship + 1st Trim correction + 2nd Trim correction
In our example this would be 30702.28 + 65 +0 = 30802.28 T
8. Density correction
We have now got the displacement for quarter mean draft. To this
displacement we have applied 1st trim correction and 2nd trim
correction.
We now have vessel’s actual displacement. But this displacement is in

salt water density of 1.025 as most of the hydrostatic tables have the
data for that density.
Now if the water density around the vessel is different than 1.025, the
displacement of the vessel will change.
Why ? As per archimedes principle the ship displaces water equal to its
own weight. If the density of the water is more, ship would displace
less volume of water (less draft). And if density of the water is lesser,
it would need to displace more volume of water (more draft) to have
same weight as of the ship itself.
For draft survey, we need to measure the density of dock water just
before or after reading the visual drafts. The density is measured by
draft survey hydrometer with a sample of dock water drawn from
around the vessel.
The density of dock water changes with depth. So it is important to

know at what depth the sample is drawn. Many take the sample from a
depth that is half the draft of the vessel. Others prefer to take the
sample by running the emergency fire pump.
Now say we have measured the density and we have the dock water
density as 1.01
So how to correct the displacement we calculated so far for density ?
So in our example it will be 30802.28 x 1.01/1.025. That will be equal

to 30351.51.
9. Cargo quantity from initial and final displacement
Apart from calculating the displacement, we need to to know the

existing weights on vessel.
For example we need to know the exact weight of ballast, Fuel oil,
Lube oil, fresh water etc on board on arrival. That is not a difficult
thing to know. But there are some best practices.
First it is easier to measure the quantity if a tank is either completely

full or completely empty. This also removes the ambiguity and
measurement error.
Second, the vessel must not be down by head (negative trim). This is
because it brings ambiguity to the actual quantity of ballast in a tank.
Third, since we need to know the weight of the ballast, we must know
the density of the water in the ballast. We will know the volume from
the sounding table and multiplying with the density will give the weight
in each ballast tank.
Fourth, we need to measure and sound each space on ship and not
assume that it is empty. For example if there is any void spaces, we
must sound these spaces as well.
So now we will know what contributes to the the arrival displacement

of the ship.
Arrival displacement = Lightweight of ship + Ballast + Fuel + Fresh

water + Lube oil + Constants
And among these things we know the quantity of ballast, fuel, lube oil,
and fresh water.
We need to repeat this calculation and measurement of all spaces after

completion of loading.
Departure Displacement = Cargo + Lightweight of ship + Ballast +

Fuel + Fresh water + Lube oil + Constants
Lightweight of the ship and constants will remain same and so these
does not matter. We would know the arrival and departure
displacement from draft survey. All other weights we know by
sounding and measurement. The only known is the cargo loaded. It is
simple mathematics then to know the cargo quantity.
10. Calculating constants on arrival
Calculating constants is not really required if our aim is only to know

the weight of the cargo loaded. This is because the the quantity of
constants will not change.
But calculating the constants on arrival is a good practice. This gives a

fair idea of the correctness of calculation. For example, let us say we
know that constants will be in the range of 200 to 300 tons.
If initial calculations give too high or too low constants, we know
something is wrong somewhere.
We can sometimes get negative constants. This would mean that we

have done some mistake and we must find it and correct it. It may be
that we have wrong drafts, wrong soundings etc. Whatever it is, we
must correct it before loading starts.
Conclusion
Draft survey is widely used for cargo measurement. It is acceptable

way of measuring the cargo quantity.
The calculation however requires practice. It may sometimes be

confusing to seafarers using the draft survey for the first time. This can
lead to the errors in calculations and cargo claims.
We must know the basics of the draft survey. Once we know that draft
survey would not look that difficult.

Here Is All You Wanted To Know About Draft Survey Calculations

Uploaded by

Copyright:

Available Formats

Here Is All You Wanted To Know About Draft Survey Calculations

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Here Is All You Wanted To Know About Draft Survey Calculations

Uploaded by

Copyright:

Available Formats

Here Is All You Wanted to Know About

Draft Survey Calculations

Well draft survey uses a similar principle to measure the cargo

So in this post I will discuss about how to go about measuring the

1. Why Draft survey ?

On tankers, the measurement of cargo quantity loaded is simple. We

So let us see how we need to go about draft survey.

2. Basics of Draft survey

With draft survey calculations, all we want to know is the difference in

Other weights : 1000 T

Other weights : 1000 T

The difference in displacement is 30000 T. Out of this 5500 T of

It is simple calculation to know the quantity of the cargo loaded which

3. Draft of the vessel

There are two drafts for a vessel.

 Draft at forward and aft perpendiculars and at midship of these two.

 Drafts at actual draft marks painted on ship side.

So to get the displacement from the trim and stability booklet, we

Exclusive Bonus: Download Excel Sheet of Draft Survey Calculation

Apparent Trim = 2.1 m

As I said we need to bring these drafts to the perpendiculars.

The formula for correction to the visuals drafts to bring it to the

 Errors in reading few of the visual drafts

 Errors due to Hog or Sag of the vessel

To minimise these errors we finalise the draft of the vessel by having

Mean of means is considered to be the accurate draft of the vessel at

4. Calculating displacement of the ship

We may have to interpolate to get the exact displacement.

5. 1st Trim correction

As per Archimedes principle, a floating ship displaces the amount of

The formula for 1st trim correction is

Sign of 1st trim correction

6. 2nd Trim correction

2nd Trim correction takes care of this change of position of LCF

The formula for 2nd trim correction is

With this value of Dm-Dz, we will get 2nd Trim correction as 35 T.

The 2nd trim correction is always positive.

So the actual displacement with respect to the draft at LCF will be

Displacement at Midship + 1st Trim correction + 2nd Trim correction

In our example this would be 30702.28 + 65 +0 = 30802.28 T

We now have vessel’s actual displacement. But this displacement is in

The density of dock water changes with depth. So it is important to

So how to correct the displacement we calculated so far for density ?

So in our example it will be 30802.28 x 1.01/1.025. That will be equal

9. Cargo quantity from initial and final displacement

Apart from calculating the displacement, we need to to know the

First it is easier to measure the quantity if a tank is either completely

So now we will know what contributes to the the arrival displacement

Arrival displacement = Lightweight of ship + Ballast + Fuel + Fresh

We need to repeat this calculation and measurement of all spaces after

Departure Displacement = Cargo + Lightweight of ship + Ballast +

10. Calculating constants on arrival

Calculating constants is not really required if our aim is only to know

But calculating the constants on arrival is a good practice. This gives a

We can sometimes get negative constants. This would mean that we

Draft survey is widely used for cargo measurement. It is acceptable

The calculation however requires practice. It may sometimes be

You might also like