Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 659 views

    Hilti Concrete Repair

    Uploaded by

    niroshnirosh
    This document provides a method statement for sealing structural cracks with Hilti products CI 060 and CC 412-1. It outlines the surface preparation including cleaning the crack and marking packer points. It then details testing the crack for leaks, injecting the CI 060 resin chemical, and taking core samples to check penetration. The technical sales manager, T.D.Wijitha Kumara, offers to demonstrate the process and can be contacted for any clarification.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Hilti Concrete Repair

    Uploaded by

    niroshnirosh
    659 views4 pages
    This document provides a method statement for sealing structural cracks with Hilti products CI 060 and CC 412-1. It outlines the surface preparation including cleaning the crack and marking packer points. It then details testing the crack for leaks, injecting the CI 060 resin chemical, and taking core samples to check penetration. The technical sales manager, T.D.Wijitha Kumara, offers to demonstrate the process and can be contacted for any clarification.

    Original Description:

    Concrete Repair

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a method statement for sealing structural cracks with Hilti products CI 060 and CC 412-1. It outlines the surface preparation including cleaning the crack and marking packer points. It then details testing the crack for leaks, injecting the CI 060 resin chemical, and taking core samples to check penetration. The technical sales manager, T.D.Wijitha Kumara, offers to demonstrate the process and can be contacted for any clarification.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    659 views4 pages

    Hilti Concrete Repair

    Uploaded by

    niroshnirosh
    This document provides a method statement for sealing structural cracks with Hilti products CI 060 and CC 412-1. It outlines the surface preparation including cleaning the crack and marking packer points. It then details testing the crack for leaks, injecting the CI 060 resin chemical, and taking core samples to check penetration. The technical sales manager, T.D.Wijitha Kumara, offers to demonstrate the process and can be contacted for any clarification.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Hilti Centre,

    No. 207, Nawala Road, Nugegoda, Sri Lanka


    Te. 0114713352, 0114542320
    Fax. 0114723208
    Email. hunterhc@eol.lk

    Method Statement for structural crack sealing with HILTI


    CI 060 and CC 412-1
    Surface Preparation
    • Clean the crack line with wire brush and compressed air to free from dust or any
    other impurities.
    • Mark the non-return valve (packer) points on the crack line as per spacing given
    below

    Crack width Packer spacing


    (mm) (mm)
    0.2 - 0.5 < 150
    0.5 - 1.0 150
    1.0 - 2.0 200
    2.0 - 3.0 250
    > 3.0 300

    • Close the crack line with CC 412-1 crack sealing compound 40mm wide and
    2mm thick by leaving packer points ( Follow the instructions given by the
    supplier for mixing of CC412-1)
    • Fix the packers on points with same crack sealing compound
    • Keep the system for 4 hrs to cure

    Testing of crack line for any leakage


    • Pure water to be injected to the line with the use of empty tube of CI 060 to check
    any leakage from packers and sealing line.
    • If found any leakage, it has to be repaired with same CC 412- 1 sealing compound
    and keep to cure
    • If necessary the line to be checked again
    • Water to be removed from the line and keep for minimum 2 hrs to dry before
    chemical injection
    Chemical Injection
    • Insert CI 060 chemical tubes in a vessel with ice cubes to bring down the
    temperature to increase the pot life time of chemical.
    • Tap the CI 060 injection cartridge lightly on the rear side with a hammer. The
    glass cylinder breaks and releases the hardener. Mix by see-saw motion for app.
    20 motions – Do not shake.
    • Insert the cartridge to the dispenser and remove the seal of cartridge and connect
    the hose provided.
    • Hose to be connected to the packer (bottom most packer) with the cap nut
    provided.
    • Insert the air relief stopper into the next packer above.
    • Inject the CI 060 resin until it appears visibly in the next packer above.
    • Then detach the connection hose from the packer and plug it to next higher
    packer. Repeat this sequence up to the end of the crack.
    • System has to be kept for 7 days for full curing but after 24 hrs, packers can be
    removed and surface can be ground to get smooth surface.

    Proof for chemical penetration


    • At least 82mm dia. core sample has to be taken initially to find out the crack
    depth and similar sample has to be taken after 2 days to find the chemical
    penetration.

    Please see the attachment for technical specifications of product. Sample demonstration
    can be done at your site as per your instructions but necessary scaffolding, working
    platforms etc to be provided by you. For any clarification, please do not hesitate to
    contact undersign.

    Thanking you.
    Yours truly,

    T.D.Wijitha Kumara
    B.Sc.Eng(Hons);CEng;MIE(SL);MSSE;MBA
    Technical Sales Manager
    Hilti – Sri Lanka
    M.(0094) 0717772815, 0773553815
    T (0094)0114713352, 0114542320
    F (0094) 0114723208
    E hunterhc@eol.lk
    E wijithatdwk@yahoo.com

    You might also like