100

NOTES

615 1. ALL DIMENSIONS ARE IN MILLIMETRES UNLESS OTHERWISE

PROPOSED STEEL PARAPET, SEE DRAWING SPECIFIED.
SWAN2-ATK-SBR-XXXX-DR-CB-000210 3000 TYP.
2. THIS DRAWING SHALL BE READ IN CONJUNCTION WITH ALL
500 500 RELEVANT DRAWINGS AND SPECIFICATIONS.

NON STRUCTURAL ST2 MIN. MIN. 3. FASCIA PANEL SHOWN INDICATIVELY. FOR DETAIL REFER
PROPOSED IN-SITU INSITU CONCRETE FILL TO DWG SWAN2-ATK-SBR-XXXX-DR-CB-000900
Millimetres

50
CONCRETE CAPPING TO MATCH TOP OF 4. EXISTING RETAINING WALL THICKNESS SHOWN ARE FROM
BEAM KERB RECORD DRAWINGS. CONTRACTORS TO CONFIRM ACTUAL
2.5% WALL THICKNESS PRIOR TO CONSTRUCTION OF CONCRETE
EDGE BEAM.
NEW KERB LOCATION
5. FOR REINFORCEMENT DETAILS OF TYPICAL CAPPING BEAM
MODIFICATION REFER DRAWING NO.
SWAN2-ATK-SBR-XXXX-DR-CB-1601.
PROPOSED STEEL PARAPET, SEE DRAWING 6. FOR EXTENT OF RETAINING WALL REFER DRAWING NO.
SWAN2-ATK-SBR-XXXX-DR-CB-000210 SWAN2-ATK-SBR-XXXX-DR-CB-000100.

750
10

450 750
7. FOR B* DIMENSION UP TO 215 mm, TYPE 1 CAPPING BEAM IS
APPLICABLE AND FOR B* DIMENSION MORE THAN 215 mm,
0

TYPE 2 CAPPING BEAM IS APPLICABLE.

DO NOT SCALE

POST ANCHORS TO BE 8. FOR EXPANSION JOINT DETAILS REFER DRAWING

850 CAST IN DURING SWAN2-ATK-SBR-XXXX-DR-CB-000901.
EXISTING BRICK CLADDING
CONSTRUCTION OF 9. TYPE 1 DETAIL IS FOR THE LOCATIONS CONTAINING FASICA
CAPPING BEAMS PANELS, WHEREAS TYPE 2 DETAIL IS FOR THE OTHER
LOCATIONS WHERE THERE IS NO FASCIA PANELS.
510 CONTRACTOR TO IDENTIFY THE SAME ON SITE PRIOR TO
CONSTRUCTION.

PROPOSED IN-SITU CONCRETE CAPPING BEAM

12mm EXPANSION JOINT
(REFER NOTE 8)

EXISTING RETAINING WALL

KEY:
PROPOSED CONCRETE CAPPING BEAM

CJ
EXISTING BRICK CLADDING

EXISTING RETAINING CEMENT MORTAR

WALL VERTICAL BARS TO
BE TRIMMED UPTO 50 mm
BELOW THE SOFFIT OF NON STRUCTURAL CONCRETE, ST2
CAPPING BEAM
EXISTING BRICK CLADDING
EXISTING RETAINING EXPANSION JOINT
WALL

ABBREVIATIONS:-
1 DETAIL (TYPE 1 CAPPING BEAM) ELEVATION OF EXPANSION JOINT DETAILS (TYP.)
MIN.
Ø
-
-
MINIMUM
DIAMETER
000601 SCALE 1: 10 TYP. - TYPICAL
SCALE 1:10 (FASCIA PANELS NOT SHOWN FOR CLARITY) CJ - CONSTRUCTION JOINT
(SEE NOTE 9)
PROPOSED STEEL PARAPET, SEE DRAWING
SWAN2-ATK-SBR-XXXX-DR-CB-000210
615 Description

Status Revision Drawn Checked Reviewed Authorised Issue Date

NON STRUCTURAL ST2
INSITU CONCRETE FILL TO
PROPOSED IN-SITU Description
MATCH TOP OF THE KERB
CONCRETE CAPPING BEAM
Status Revision Drawn Checked Reviewed Authorised Issue Date
50

NEW KERB
2.5% Description
LOCATION

Status Revision Drawn Checked Reviewed Authorised Issue Date

Description

Status Revision Drawn Checked Reviewed Authorised Issue Date

450 Description
FIRST ISSUE
Status Revision Drawn Checked Reviewed Authorised Issue Date
S0 P01.4 NN GS --- --- 02/07/19
Drawing Suitability Status

WORK IN PROGRESS S0
850
Epsom Gateway
Ashley Avenue
Epsom
Surrey
KT18 5AL
Tel: +44 (0)1372 726140
Fax: +44 (0)1372 740055
Copyright C Atkins Limited (2017) www.atkinsglobal.com
Client

Project Title
CJ Swanswell Viaduct Refurbishment Design
Phase 2
Drawing Title
EXISTING RETAINING
500
WALL
RETAINING WALL UPSTAND MODIFICATION
EXISTING RETAINING
EXISTING BRICK CLADDING SAFETY, HEALTH AND ENVIRONMENTAL INFORMATION GA, SHEET - 2
WALL VERTICAL BARS TO
BE TRIMMED UPTO 50 mm IN ADDITION TO THE HAZARDS/RISKS NORMALLY ASSOCIATED WITH THE TYPES OF WORK DETAILED ON
THIS DRAWING, NOTE THE FOLLOWING SIGNIFICANT RESIDUAL RISKS
BELOW THE SOFFIT OF
CAPPING BEAM CONSTRUCTION
SERVICES, LIVE TRAFFIC, DEMOLITION AND WORKING AT HEIGHT Drawing Number
MAINTENANCE/CLEANING Project Originator Volume

NONE SWAN2 - ATK - SBR -

2 DETAIL (TYPE 2 CAPPING BEAM)
USE
XXXX - DR - CB - 000602
NONE Location Type Role Number
000601 SCALE 1: 10 DECOMMISSIONING/DEMOLITION
Original Project
(SEE NOTE 9) SERVICES Size: A1 AS
Scale: SHOWN Ref. No: 5166344 Sheet: 2 of Rev: P01.4
This Drawing is saved on ProjectWise. Plotted: 02/07/2019 18:41:58 By: NAIN6314