Professional Documents
Culture Documents
Paper On Plastic To Road
Paper On Plastic To Road
(Volume2, Issue5)
Available online at www.ijarnd.com
ABSTRACT
Plastic waste is one such resource, a major component of solid waste which is abundantly available and disposed
of without proper treatment. There has been an exponential growth in municipal plastic waste disposal especially
in urban areas which deteriorates the beauty of the landscape. Plastic was found to be an effective binder for
bitumen mixes used in flexible pavements. This efficient method helps the pavements to resist higher temperature
by minimizing the formation of cracks and reducing rainwater infiltration which otherwise leads to the
development of potholes. These pavements have shown improved crushing and abrasion values and reduced water
seepage. Plastic roads would be a boon for India’s hot and extremely humid climate, where temperatures
frequently cross 50°C and torrential rains create havoc, leaving most of the roads with big potholes.
Bituminous Concrete (BC) is a composite material mostly used in construction projects like road surfacing,
airports, parking lots etc. It consists of asphalt or bitumen (used as a binder) and mineral aggregate which is
mixed together & laid down in layers then compacted. Now a day, the steady increment in high traffic intensity in
terms of commercial vehicles, and the significant variation in daily and seasonal temperature put us in a
demanding situation to think of some alternatives for the improvisation of the pavement characteristics and quality
by applying some necessary modifications which shall satisfy both the strength as well as economic aspects.
Also considering the environmental approach, due to excessive use of polythenes in the day to day business, the
pollution to the environment is enormous. Since the polythenes are not biodegradable, the need of the current
hour is to use the waste polyethene in some beneficial purposes.
1. INTRODUCTION
Most of the paved roads in our country have granular sub base and base; bituminous base and wearing courses.
Plastic is a very versatile material. Due to the industrial revolution, and its large scale production plastic seemed
to be a cheaper and effective raw material. Today, every vital sector of the economy starting from agriculture to
packaging, automobile, electronics, electrical, building construction, communication sectors has been virtually
revolutionized by the applications of plastics. Plastic is a non-biodegradable material and researchers found that
the material can remain on earth for 4500 years without degradation. Several studies have proven the health hazard
caused by improper disposal of plastic waste. Plastics, a versatile material and a friend to common man become a
problem to the environment after its use. Disposal of a variety of plastic & rubber wastes in an eco-friendly way
is the thrust area of today’s research. Looking forward the scenario of present lifestyle a complete ban on the use
of waste plastic cannot be put, although the waste plastic taking the face of a devil for the present and the future
generation. But the use of waste plastics in road construction is gaining importance these days because plastic
roads perform better than ordinary ones and the plastic waste considered to be a pollution menace, can find its
use. The use of waste plastic for coating the aggregates of the bituminous mix found to improve its performance
characteristics. Recycled polyethene carry bags were shredded into small sizes and is coated on aggregates of the
mix at a specified temperature. Bituminous mixes were prepared with 60/70 bitumen and plastic coated
aggregates/ordinary aggregates with cement as a filler material. The uses of plastic waste help in substantially
improving the abrasion and slip resistance of flexible pavement and also allows to obtain values of splitting tensile
strength satisfied the specified limits while plastic waste content is beyond 30% by weight of mix. If the consistent
mixing time and mixing temperature are not provided for bitumen– modifier mix, modified bitumen cannot exhibit
good performance in situ, thus premature failures will occur. Therefore, there are certain recommended mixing
time, mixing temperature and modifier content for all the polymers with a trademark. This all should be taken in
mind while mixing and laying of roads is to be done using plastic waste. The plastic road would be a boon for
India. In hot and extremely humid climate durable and eco-friendly plastic roads are of greatest advantages. This
will also help in relieving the earth from all type of plastic waste.
2. LITERATURE REVIEW
1. Fransis Hveem (1942) “Optimum quantity of bitumen inroads” who was a project engineer of California
Department of Highways, has developed the Hveemstabilometer in 1927. He did not have any previous
experience on judging, the required mix of its colour, hence he decided to measure various mixture
parameters to find the optimum quantity of bitumen [Vallerga and Lovering 1985]. He had used the surface
area calculation concept, (which was already in use, at that time for the cement concrete mix design), to
estimate the quantity of bitumen actually required.
2. Anzar Hamid Mir (2015) “Plastic waste in pavement construction” studied the visco-elastic nature of
binders and found that the complex modulus & phase angles of the binders, need to be measured, at
temperatures and loading rates which different resemble climatic and loading conditions.
3. Vatsal Patel et al (2014) “Utilization of plastic waste in road” described that the effect of wax in bitumen
can be reduced by adding EVA (Ethyl Vinyl Acetate), aromatic resin and SBS in the waxy bitumen. The
addition of 4% EVA or 6% SBS or 8% resin in waxy bitumen effectively reduces the Susceptibility to high
temperatures, bleeding at high temperature and brittleness at a low temperature of the mixes.
4. Kurmadasu Chandramouli et al (2016) “Plastic waste: its use in the construction of roads ” reported
that asphalt concrete using polyethylene modified binders were more resistant to permanent deformation at
elevated temperature and found improvement in stripping characteristics of the crumb rubber modified mix
as compared to unmodified asphalt mix.
5. Amit P. Gawande (2013)“Economics And Viability Of Plastic Road” evaluated flexural fatigue life of
asphalt concrete modified by 3% crumb rubber as part of aggregated and reported that fatigue life and creep
properties of the polymer modified mixes increased significantly as compared to unmodified asphalt mixes.
6. Justo et al (2002) “Asphalt concrete mixes” at the Centre for Transportation Engineering, of Bangalore
University, used processed plastic bags as an additive in asphalt concrete mixes. The properties of this
modified bitumen were compared to that of ordinary bitumen. It was noted that penetration and ductility
values, of modified bitumen, was decreasing with the increase in the proposrtion of the plastic additive.
7. Sasane Neha .B. et al (2015) “Application of waste plastic as an effective construction material in
flexible pavement” polyethylene as one sort of polymers is used to investigate the potential prospects to
enhance asphalt mixture properties. The objectives also include determining the best type of polyethylene to
be used and its proportion. Two types of polyethylene were added to coat the aggregate High-Density
Polyethylene (HDPE) and Low-Density Polyethylene (LDPE). The results indicated that grinded HDPE
polyethylene modifier provides better engineering properties. The recommended proportion of the modifier
is 12% by the weight of bitumen content. It is found to increase the stability, reduce the density and slightly
increase the air voids and the voids of mineral aggregate.
8. S. Rajasekaran et al (2009) “Reuse of waste plastic coated aggregate” Marshall’s mix design was carried
out by changing the modified bitumen content at constant optimum rubber content and subsequent tests have
been performed to determine the different mix design characteristics and for conventional bitumen (60/70)
also. This has resulted in many improved characteristics when compared with straight run bitumen and that
too at reduced optimum modified binder content (5.67%).
3. OBJECTIVES
1. To prepare the Marshall Stability samples with plastic waste and without plastic waste.
2. To perform Marshall Stability test on the samples prepared.
3. To compare the various properties of the bituminous road and plastic bituminous road.
4. To identify the optimum proportion of waste plastic to be added in the bitumen mix for getting the
required strength.
5. To reduce the disposal problem of plastics.
4. METHODOLOGY
Segregation: Plastic waste collected from various sources is separated from other wastes.
Testing of materials: Tests will be performed on the materials i.e. aggregate and bitumen.
1. Following are the tests to be performed on aggregate:
a) Aggregate impact value test
b) Los Angeles abrasion test
c) Water absorption test
d) Specific gravity test
e) Stripping value test
Preparation of samples: Six Marshall Stability samples will be prepared out of which three will be with
the plastic of varying percentage (5%, 10%, and 15%) and three samples without plastic waste.
Performing Marshall Stability test: Marshall Stability test will be performed on all of the samples
prepared.
5. RESULTS
Following are the tests performed and the results obtained
1. TESTS ON AGGREGATE
Table-1: Results of tests on aggregate
2. TESTS ON BITUMEN
Table-2: Results of tests on bitumen
Sample No. Bitumen content (%) Plastic content (% Marshall Flow value
by weight) stability(kg) (mm)
1 4 0 950 3.1
2 5 0 1170 3.3
3 6 0 1240 3.6
4 4 5 1560 3.9
5 5 10 1720 4.5
6 6 15 1980 5
2000
1980
Stability (kg)
1500 1720
1560 Samples without plastic
1240 waste
1000 1170
950 Samples with plastic
500 waste
0
4 5 6
Bitumen Content(%)
FLOW VALUE
10
5
9
4.5
8 3.9
Flow Value (mm)
7
6
5 Samples with plastic
3.3 3.6 waste
4 3.1
3 Samples without plastic
waste
2
1
0
4 5 6
Bitumen Content (%)
6. CONCLUSION
From the study of the behavior of plastic waste modified BC, we can conclude that the modified mix possesses
improved Marshall Characteristics. It is observed that Marshall Stability value increases with plastic content and
we observed that the Marshall Flow value decreases upon addition of polythene i.e. the resistance to deformations
under heavy wheel loads increases. From all the experiments performed we can conclude that the addition of
plastic waste enhances the various properties of an ordinary bituminous road. Considering these factors we can
assure that we can obtain a more stable and durable mix for the pavements by polymer modifications. This small
investigation not only utilizes beneficially, the waste non-degradable plastics but also provides us an improved
pavement with better strength and longer life period. This study will have a positive impact on the environment
as it will reduce the volume of plastic waste to be disposed of by incineration and land filling. It will not only add
value to plastic waste but will develop a technology, which is eco-friendly.
7. REFERENCES
1. AmitGawande, G.S Zamre, V.C Renge G.R Bharsakalea and SaurabhTayde, utilization of waste plastic
in asphalt of roads, scientific reviews and chemical communication.
2. Dr. Satish Chandra, Shiv Kumar & Rajesh Kumar Anand, “Soil Stabilization with Rice Husk Ash and
line Sludge”, India Highways, Indian Roads Congress, vol33 No. 5, May 2005, pp.87-98
3. Dr. S.S.Verma, “Road from Plastic state.”,ScienceTech Entrepreneur, March 2008 Gianni A.K. Modi,
A.J., “Bio Enzymatic Soil Stabilizers for Construction of Rural Roads”, International Seminar on
Sustainable Development in Road Transport, New Delhi-India 8-10November 2001
4. IRC: SP: 20-2002. “Rural Roads Manual”, Indian Roads Congress
5. Mroueh, U. M., and Wahlstrom, M. (2002). “By-Products and Recycled Materials in Earth Construction
in Finland M an Assessment of Applicability.” Resources, Conservation and Recycling, No. 35,2002,
pp. 117M129
6. Miss Aproova ,use of plastic waste in flexible pavements, international journal of innovative research in
engineering and management
7. Sherwood, P. T. (1995). “Alternative materials in road construction. “Thomas Telford Publications,
London, 1995
8. Tara Sen, Umesh Mishra, “Usage of Industrial Waste Products in Village Road Construction,”
International Journal of Environmental Science and Development, Vol. 1, No. 2, June 2010
9. Vasudevan .R, utilization of waste plastics for flexible pavement, Indian High Ways (Indian Road
Congress), Vol.34, No.7. (July 2006).
10. Wes Heidenreich, “Recycled plastic in highway construction and maintenance.” State Research report
#525,July 1997.