RE 95533/03.

96

Scavenging and Pressure RE

Relief Valve Block SDVB 95533/03.96
Control Elements of the A4VSG and A2P
Brueninghaus Hydromatik Replaces 01.82

The scavenging and pressure relief valve block serves to main- The set pressure value corresponds to the pressure drop be-
tain the feed pressure, to exhaust excess oil and to limit the tween high and low pressure side. This valve type is extremely
operating pressure in a closed hydraulic circuit. compact in relation to its flow capacity.
Both service ports A and B can be pressurised with high or low The SDVB can also be used as a double-acting pressure relief
pressure as required. The high pressure controlled scavenging valve. When used as a relief valve, the supply line to the sca-
spools ensure that upon changeover of the gigh and low pressure venging valve is closed.
sides the scavenging valve is connected to the low pressure By means of independently or direct mounted unloading valves,
side. the pilot valves can be connected externally with the tank or
Pilot operation of the double acting pressure relief valves allows internally with the low pressure side. With this function the SDVB
simple setting, with minimum force, of the required pressure 30 and 50 can serve as a bypass valve. For high dynamic swivel
value for both pressure sides of the circuit. These settings may operations with flushing and pressure relief valve block SDVB,
be carried out independent of one another. On sizes 30 and 50, when changing the high pressure side there will be free flow
remote control is also possible via external pilot oil connections between A and B for a short time. Direct operated valve blocks
(X and Y). When the relief valves are actuated, oil flows from are suitable for this application and are available in sizes 16
the high pressure to the low pressure side. and 30 on request.

Brueninghaus Hydromatik 1
RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

Ordering code
SDVB /
Description
scavenging and pressure relief valve block piloted SDVB

Size
size 16 16
size 30 30
size 50 50

Model (see unit dimensions)

without direct operated flushing valve without pre-load valve N
with direct operated flushing valve without pre-load valve S
with direct operated flushing valve without pre-load valve T*
without direct operated flushing valve with pre-load valve V
with direct operated flushing valve with pre-load valve W
with direct operated flushing valve with pre-load valve Z*
* Model T and Z only for SDVB 16 (in prep.) and SDVB 30

Control type
pilot oil pilot oil unloading
supply drain with / without
internal internal ● 1
internal external ● 2
external internal ● 3
external external ● 4
internal external ● 51)
(de-energised when closed)
internal internal ● 6
with external pilot ports
X-Y (plugged)
internal external ● 71)
(de-energised when open)
1
) both solenoids must be operated simultaneously

Model of port plate

port plate M 33 A
port plate M 42 B
port plate M 48 C
port plate SAE 1 1/2" D
without port plate N

Series
20 30
SDVB 16
Symbols for control type 5 SDVB 30/50
de-energised when closed A open B

Voltages types for control type 5

12 V DC voltage - A closed 1
24 V DC voltage - B open 2
110-R AC voltage 3
220-R AC voltage 4
220-50 AC voltage 5

2 Brueninghaus Hydromatik
 RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

Construction

SDVB 16 pre-load valve if A4VSG mounted

SDVB 30 pre-load valve if A4VSG and A2P directly mounted

SDVB 50 pre-load valve if A4VSG and A2P directly mounted

Brueninghaus Hydromatik 3
RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

Control type (with pre-load valve)

Control Type 1 Control Type 2

K1 Y K1

MB MA MB MA

MSp MSp

B E A B E A

Control Type 3 Control Type 4

K1 Y K1

MB MA MB MA

XA XA

XB XB
MSp MSp

B E A B E A

Control Type 5 Control Type 6 Control Type 7

Y K1 Y K1 Y K1

MB MA MB MA MB MA

XA

XB
MSp MSp MSp

B E A B E A B E A

The types of control shown only apply to size 16.

With the SDVB 30 and 50 there are two X and two Y ports.
Control types for size 30 are same as those for sizes 16 and 50
but without gauge ports MA and MB.

4 Brueninghaus Hydromatik
 RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

Technical data (partly to VDI 3276)

Design: combined scavenging and pressure relief valves Pressure setting range:
controlled by operating pressure Operating pressure: pv min…pv max = 50…400 bar
Scavenging pressure at nominal flow Q NSp: SDVB 16, 30 and 50
Mounting: flange model with O-ring seal (4 fixing holes in are infinitely adjustable. Please state the required pressure
housing) setting for operating pressure and scavenging pressure when
ordering. More details see RE 92100.
Pipe connections and connection sizes: see Unit Dimensions
Fluid temperature range
Weight (kg) ϑ m min…ϑm max = –20° C…+80° C
Size 16 30 50
without subplate 6,5 23 61 Viscosity range νmin…νmax = 10…1000 mm2/s

with subplate 30 68 Nominal flow

Size 16 30 50
Mounting position: optional
Main circuit QN (L/min) 200 600 1200
Direction of flow: from A to B resp. B to A and from A to K1 resp. Scavenging circuit QNSp (L/min) 40 100 200
B to K1

Operating pressure range: pN = 0…400 bar

The pressure measured at port XA/B is only identical to the

pressure in the service line as long as the pressure relief valve
is not actuated. Once the pilot valve has begun to open, the
operating pressure in the main line can be around 15% higher.
It is therefore recommended to measure the operating pressure
direct at MA or MB resp. A or B.

∆p-Q-Characteristics

Operating pressure p = f (Q) Scavenging pressure pSp = f (QSp)

Operating pressure p (bar)

Pressure differential

Size 16
Size 30
Size 50
∆p (bar)

Size 16

Flow Q (L/min) Size 30…50

Size 16

Size 30

Size 50
Flow Q (L/min)
Pressure setting (Operating pressure)
Size 16 30 50
p (bar/Umdr.) approx. 150 105 105

Brueninghaus Hydromatik 5
RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

SDVB 16 Switching pressure

In order to switch both sides of the circuit A and B to the
scavenging valve, a pressure differential between the high
Low pressure pSp (bar)

pressure and low pressure sides is required.

This pressure differential and therefore the switching pressure
on the high pressure side is dependent on the setting on the low
pressure side. With the SDVB 30 and 50, the spring force effect
must also be taken into consideration, since this requires a
pressure increase of around 9 bar until the valve poppet is fully
open (see diagrams on left).

Max. pilot oil volume

QSt max (taken from main circuit)
Size 16 30 50
QSt max (L/min) ≈4 ≈5 ≈6
pHD (bar)
Remote control
To allow the setting of different pressure values for the pressure
relief valves, external pilot oil connections "X" and "Y" are
SDVB 30 and 50
provided for remote control.

Functional variations
The SDVB 16 to 50 may also be used as a double acting pressure
Low pressure pSp (bar)

t
u re f fec relief valve.
e ss ee If only the double acting pressure relief valve function is required,
pr rc
fo the supply line to the scavenging valve is closed or the pressure
i ng ing
ck r setting of the scavenging valve is set higher than that on the
Cr
a Sp relevant low pressure side.

pHD (bar)

Co-ordination with axial piston units

Direct mounting
SDVB Axial piston unit
A4VSG A2P, Series 5
40 71 125 180 250 355 500 750 1000 250 355 500 1000
16 ● ● ● ●
30 ● ● ● ● ● ●
50 ● ● ●

6 Brueninghaus Hydromatik
 RE 95533/03.96
Before finalising your design, please request a certified drawing.
Scavenging and Pressure Relief Valve Block SDVB Subject to revision.

Unit Dimensions Size 16

Control Type 1
85

M14x1.5
209 12 80
O-Ring 22x3
A/B
44.5

ø25
Z
38.5

ø16
M10

ø34

89
129

M22x1.5
Pressure relief valve A
Pressure relief valve B
Model V

12 67 Model W

M14x1.5
Control Type 2; 3; 4; 6
50 100

ø25
10

XA XB
11

1.5 XA (XB)

Control Type 5; 7 221

Y
10

Plug
DIN 43650-AF2-Pg 11
is not included in supply
(see RE 08000)
View Z 112
90
50
C D
22.5

Section C-D
7.5
43.5

65
87

E
B
32.5

A ø9.5
O-Ring 19x2

70

Brueninghaus Hydromatik 7
RE 95533/03.96
Before finalising your design, please request a certified drawing.
Scavenging and Pressure Relief Valve Block SDVB Subject to revision.

Unit Dimensions Size 30

148

Model N (V)

Control Type 1
Model T (Z)
263
51 173
O-Ring 39x3
B A
A/B

ø30
125

Model S (W)
76

51
M16
24 62
137.5
Pressure relief valve A Pressure relief valve B

Control Type 2; 3; 4; 6 26
ø25
225 M14x1.5
XA XB XA YA
YB
60
YA
60

XA/YA XB/YB XA YA

Control Type 5; 7 26
ø25
225 M14x1.5
XA XB XA YA
YB
60

YA
194

Plug
DIN 43650-AF2-Pg 11
is not included in supply
(see RE 08000)

View Z 51
Section A-B Section C-D
33.5
D C pre-load valve
35

110

19
54

M33x2 ø16
8.3

M22x2
ø34
140

8 Brueninghaus Hydromatik
 RE 95533/03.96
Before finalising your design, please request a certified drawing.
Scavenging and Pressure Relief Valve Block SDVB Subject to revision.

Unit Dimensions Size 50

188.5
Control Type 1

378 Model N (V)

142
77 71 216
O-Ring 57x4
40 40 80 MSp
A/B 51
A B MA/MB

91
96

142

ø50
71
Z
97

M24
Model S (W)

92
Pressure relief valve A Pressure relief valve B 32 178

Control Type 2; 3; 4; 6 26
ø25
320 M14x1.5
XA XB XA YA
YB
80
YA 80

XA/YA XB/YB XA YA

Control Type 5; 7 26
ø25
320 M14x1.5
XA XB XA YA
YB
80

YA
214

Plug
DIN 43650-AF2-Pg 11
is not included in supply
(see RE 08000)

View Z

ø25
M14x1.5 Section A-B Section C-D
B MB MSp MA A pre-load valve

40 40
185

C D ø29
21
55
90

M48x2 O-Ring 50.47x2.62

M42x2 ø65
E
20

ø58
MSp
186

Brueninghaus Hydromatik 9
RE 95533/03.96
Before finalising your design, please request a certified drawing.
Scavenging and Pressure Relief Valve Block SDVB Subject to revision.

Subplate

SDVB 16 (M33x2) SDVB 16 (M42x2)

164
164
150
150
92
78

92
78
40

46
60
7

64

7
ø16 ø9 ø16
17

27
35

45
18

20
M33x2
M42x2
ø9 ø47
ø58

SDVB 30 SDVB 50

20 20
20.5
96.8
122

224

72
22.25 22.25
ø140 62 62
ø24 ø30

ø50 M20
50
22

45

M48x2 ø50 ø14

ø56 ø14
ø250

10 Brueninghaus Hydromatik
 RE 95533/03.96
Before finalising your design, please request a certified drawing.
Scavenging and Pressure Relief Valve Block SDVB Subject to revision.

Unit Dimensions
A4VSG with scavenging block SDVB 16

Unit Dimensions Ports

Size A1 A2 A3 MA, MB MSP K1
40 174 144 approx. 364 M14x1,5 M14x1,5 M22x1,5; 14 deep
71 177 166 389 M14x1,5 M14x1,5 M22x1,5; 14 deep
125 196,5 203 442 M14x1,5 M14x1,5 M22x1,5; 14 deep
180 196,5 203 442 M14x1,5 M14x1,5 M22x1,5; 14 deep
250 317 248 448 M14x1,5 M22x1,5 M33x2; 18 deep
355 319 248 455 M14x1,5 M22x1,5 M33x2; 18 deep
500 353 279 487 M14x1,5 M22x1,5 M33x2; 18 deep

Brueninghaus Hydromatik 11
RE 95533/03.96

Scavenging and Pressure Relief Valve Block SDVB

Brueninghaus Hydromatik GmbH, Werk Horb, D–72160 Horb, An den Kelterwiesen 14, Tel. (07451) 920, Telex 765 321, Fax (07451) 8221

12 Brueninghaus Hydromatik