Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
600 views

Simplified Static Force Procedure

1. The document describes a simplified static force procedure (NSCP 2015) for calculating seismic design forces on structures that meet certain regularity requirements. 2. The total design base shear (V) is calculated as 3% of the total seismic dead load (W) multiplied by a seismic coefficient (Ca) and divided by a response modification factor (R) from tables. 3. The total design base shear is distributed vertically to each floor by multiplying the portion of seismic dead load at each floor by the seismic coefficient and dividing by the response modification factor.

Uploaded by

Yuoyung tin
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
600 views

Simplified Static Force Procedure

1. The document describes a simplified static force procedure (NSCP 2015) for calculating seismic design forces on structures that meet certain regularity requirements. 2. The total design base shear (V) is calculated as 3% of the total seismic dead load (W) multiplied by a seismic coefficient (Ca) and divided by a response modification factor (R) from tables. 3. The total design base shear is distributed vertically to each floor by multiplying the portion of seismic dead load at each floor by the seismic coefficient and dividing by the response modification factor.

Uploaded by

Yuoyung tin
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Simplified Static Force

Procedure (NSCP 2015)


Engr. Therence Jade Villanueva
Technological Institute of the Philippines-Quezon City
Civil Engineering Department
Simplified Static Force Procedure
 Structures conforming to Section
208.4.8.1.
 Simplified Design Base Shear

3𝐶𝑎
𝑉= 𝑊
𝑅
Where:
V = Total design base shear
𝐶𝑎 = Seismic Coefficient due to soil profile (Table 208-7)
W = Total Seismic Dead Load
R = Numerical coefficient representative of the inherent over-
strength and global ductility capacity of lateral-force-
resisting systems, as set forth in Table 208-11 or 208-12
 Note: None of the irregularities should be
present:
1. Type 1, 4 or 5 of Table 208-9 (Vertical
Irregularity)
2. Type 1 or 4 of Table 208-10 (Horizontal
Irregularity)
Vertical irregularities Horizontal irregularities
(Table 208-9) (Table 208-10)
1. Stiffness irregularity – soft 1. Torsional irregularity – to be
storey considered when diaphragms
are not flexible
2. Weight (mass) irregularity
2. Re-entrant corner
3. Vertical geometric irregularity
irregularity
3. Diaphragm discontinuity
4. In-plane discontinuity in irregularity
vertical lateral-force- 4. Out-of-plane offsets
resisting element irregularity
irregularity 5. Non-parallel systems
5. Discontinuity in capacity- irregularity
weak storey irregularity

Structural Irregularities
Vertical Distribution of Shear
 The total design base shear shall be
calculated using the following equation:

3𝐶𝑎
𝐹𝑥 = 𝑤𝑖
𝑅
Where:
𝐹𝑥 = Design seismic force applied to level i, n or x
𝐶𝑎 = Seismic Coefficient due to soil profile (Table 208-7)
𝑤𝑖 = portion of W assigned to the level or floor
R = Numerical coefficient representative of the inherent over-
strength and global ductility capacity of lateral-force-
resisting systems, as set forth in Table 208-11 or 208-12
Horizontal Distribution of Shear
 Sum of all Fx or Ft above that storey.

NOTE:
 Horizontal Torsional Moments and
Overturning Effects will not be
considered in the analysis.
Example
Floor DL (kN) Storey height (m) Fx (kN) Vx (kN)
Roof 1000 3 266.6667 0
10th 1200 3 320 266.6667
9th 1200 3 320 586.6667
8th 1200 3 320 906.6667
7th 1200 3 320 1226.667
6th 1200 3 320 1546.667
5th 1200 3 320 1866.667
4th 1200 3 320 2186.667
3rd 1200 3 320 2506.667
2nd 1500 4 400 2826.667
Total 12100 31 3226.667

Design Base Shear (kN)

You might also like