MEASURING INSTRUMENTS

LEARNING OBJECTIVES

After the completion of this unit, students or readers will be able to

understand the following:

 What is the concept and importance of measurement?

 What are electrical instruments?
 How are the electrical instruments classified?
 What are the different types of electrical instruments?
 What are essentials of indicating instruments?
 What is deflecting torque and how it is provided in an indicating instrument?
 What is controlling torque and how it is provided in an indicating instrument?
 What is the importance of damping torque and how it is provided in the
indicating instruments?
 How can we differentiate between indicating and integrating instruments?
 What are moving iron instruments?
 What is the basic principle of operation and constructional details of an
attraction and repulsion-type moving iron instrument?
 What can be the errors that may occur in moving iron instruments and how
these can be minimized or taken care?
 How can a moving iron instrument used as an ammeter or a voltmeter.
 What is a PMMC instrument?
 What is the basic working principle and construction of a PMMC instrument?
 What can be the errors in PMMC instruments and how these can be
minimized?
 How can we differentiate between an ammeter and a voltmeter?
 How can the range of an ammeter or voltmeter extended?
 What are the dynamometer-type instruments?
 Why dynamometer-type instruments are used only as a wattmeter to measure
power and not as a voltmeter or ammeter?
 How a wattmeter measures actual power in AC circuits?
 What different errors may crop in wattmeters and how these can be removed
or compensated?
 What are induction-type wattmeters and how these are different to
dynamometer-type wattmeters?
 What is induction-type energy meter and how it is different to induction-type
wattmeter?
 What type of errors may occur in induction-type energy meters and how these
can be minimised or compensated?
 INTRODUCTION

Electrical measuring instruments are widely used in the modern engineering world
because of their accuracy, convenience and reliability.

These instruments are not only used to measure the electrical quantities but are also
used to measure other non-electrical quantities such as temperature, strain,
deformation, velocity and pressure with the help of transducers.

Thus, all the engineering students must be in acquaintance with these instruments.

Electrical Instruments

In electrical system, there are various electrical quantities, such as current,

voltage, power, energy, frequency, power factor, resistance, inductance, and
capacitance that are required to be measured. To measure these quantities,
various instruments such as ammeter, voltmeter, wattmeter, energy meter,
frequency meter, power factor meter, and ohm meter (or RLC meter) are
used, respectively. These instruments are known as electrical instruments.

The instruments, such as ammeter, voltmeter, energy meter, and megger,

are used to measure electrical quantities are called electrical instruments.

Classification of electrical instruments

The electrical instruments may be broadly classified as follows:

Absolute instruments: The instruments that give the value of the quantity to be
measured in terms of constants of the instrument are called absolute instruments.
Such instruments do not require any previous calibration. The common example of
this type of instrument is tangent galvanometer. The tangent galvanometer gives the
value of current in terms of the tangent of deflection produced by the current, the
radius, and number of turns of wire and the horizontal component of earth’s field.
These instruments are seldom used except in standard laboratories for standardizing
the instruments.
Secondary instruments: The instruments that determine the electrical quantity to
be measured directly in terms of deflection are called secondary instruments. Such
instruments are calibrated with standard instruments that have already been
calibrated before using them. These instruments are generally used in practical life.
The secondary instruments are further classified as follows:
Indicating instruments: The instruments that indicate the
magnitude of electrical quantity being measured instantaneously are
called indicating instruments.

Fig. 9.1 Indicating instruments (a) Ammeter (b) Voltmeter

(c) Wattmeter
In such instruments, a pointer moves over the calibrated scale to
indicate the magnitude of electrical quantity being measured. Ordinary
ammeters, voltmeters, and watt-meters fall into this category (Fig. 9.1).

Integrating instruments: The instruments that add up the electrical

quantity, that is, electrical energy and measure the total energy (in
kWh) in a given period are called integrating instruments.

Fig. 9.2 Integrating instruments (a) Induction type energy

meter (b) Digital energy meter
In such instruments, there are sets of dials or gears that register the
total quantity of electricity or the total amount of electrical energy
supplied to a circuit in a given period. The energy meters fall into this
category (Fig. 9.2).

Recording instruments: The instruments that give a continuous

record of the variations of the electrical quantity being measured are
called recording instruments. These instruments more or less are the
indicating instruments; however, in this case, the moving system
carries an inked pen that rests slightly on a chart or graph wrapped over
a drum moving at a uniform slow speed (Fig. 9.3). The motion of the
drum is in a direction perpendicular to that of the deflection of the pen.
The path traced out indicates the variations in the electrical quantity
being measured during the given period. These instruments are used
when we want to preserve the information that could be obtained later
on. A simple example of these instruments is load curve plotter placed
at the generating stations to plot variation of load at the generating
station with respect to time. The other example is Electrocardiograph
(ECG) that records the heart beats and shows the circulation of blood or
effectiveness of heart (i.e., pumping system) to diagnose heart disease.

Fig. 9.3 Recording instruments (a) Paper wrapped over a drum (b)
Inked pen tracing a graph (c) Graph traced on a paper

Effects utilized in electrical instruments to produce deflecting

torque

The principle of operation of electrical instruments depends upon various

effects produced by electric current and voltage. The various effects and the
electrical instruments in which these effects are utilised for their operation
are mentioned in Table 9.1.

Table 9.1 Effects Utilized in Various Electrical Instruments

 Instruments in which this effect is generally
Effect produced
utilized

(1) Magnetic effect Ammeters and voltmeters

Ammeters, voltmeters, and wattmeters, usua

(2) Electrodynamic effect
lly wattmeters.

Ammeters, voltmeters, wattmeters and energ

(3) Electromagnetic induct
y meters.
ion effect
Usually wattmeters and energy meters.

(4) Electrostatic effect Voltmeters only

(5) Heating or thermal effe

Ammeters and voltmeters
ct

(6) Chemical effect DC ampere-hour meters

Essentials of indicating instruments

In indicating instruments, a pointer moves over the calibrated scale to

indicate the magnitude of electrical quantity being measured. The pointer is
attached to a moving system pivoted in jeweled bearings. The forces or
torques required for satisfactory operation of indicating instruments are as
follows:

Deflecting torque: The deflecting or operating torque (Td) is produced by

making use of any one of the effects such as magnetic, electrodynamic,
and electromagnetic induction. The actual method of torque production
depends upon the type of instrument. The deflecting torque is required to
move the moving system (and hence, the pointer attached to it) from zero
position when the instrument is connected in the circuit to measure the
electrical quantity.
The torque produced by any of the abovementioned effects due to
which moving system moves (or pointer deflects) from its zero position in
an indicating instrument is called deflecting torque.

Controlling torque: The controlling or restoring torque (Tc) opposes the

deflecting torque and increases with the deflection of the moving system.
The pointer is brought to rest at a position where the two opposing
torques (i.e., deflecting torque and controlling torque) are equal. Thus, it
ensures that the deflection of the pointer is according to the magnitude of
electrical quantity being measured. If this torque was not provided, the
pointer would continue to move indefinitely and the deflection shall be
independent of the value of electrical quantity being measured.
The other function of the controlling torque is to bring the pointer
back to zero when the instrument is removed from the circuit or when the
deflecting torque acting in the instrument is removed. If this torque was
not provided, the pointer once deflected would not return to zero position
on removing the deflecting torque. This torque is either obtained by a
spring or by gravity in the indicating instruments.
Thus, in indicating instruments, the torque that brings the pointer
to zero position when the instrument is disconnected from the circuit or
the torque that allows the pointer to deflect in accordance to the
magnitude of electrical quantity is called controlling torque. It always
opposes the deflecting torque.
In spring control, one or two phosphor bronze spiral hair-springs are
attached to the moving spindle. The other ends of the springs are
attached to the fixed body or frame. In this case, the controlling torque
(Tc) is directly proportional to the angle of deflection (θ ), that is, Tc ∞ θ.
In gravity control, a small adjustable weight is attached to the moving
system in such a way that due to gravity, it tries to bring the pointer to
zero position when it is deflected. In this case, the controlling torque (Tc)
is proportional to the sine of angle of deflection (θ ), i.e., Tc ∞ sinθ.

Damping torque: When deflecting torque is applied to the moving system, it

deflects the pointer. While the controlling torque controls the deflection and tries to
stop the pointer at its final position, say at F, as shown in Figure 9.4, where deflection
torque is equal to controlling torque (i.e., Td = Tc). However, due to inertia, the pointer
oscillates around its final position Fbefore coming to rest. These oscillations are
undesirable because it causes delay in taking the reading. Then what to do? In order
to avoid these oscillations and to bring the pointer quickly to its final deflected
position, damping torque is provided. The damping torque opposes the movement
(forward or backward) of the pointer and operates only when the system is moving. In
fact, damping torque acts like a brake on the moving system.

Thus, in indicating instruments, the torque that suppresses the undue

oscillations of the pointer and brings the pointer to its final position
quickly is called damping torque. It always acts opposite to motion.
 Fig. 9.4 Oscillating pointer
Underdamping: When the damping torque provided in an indicating
instrument is such that the pointer oscillates around its final position
for long period, the instrument is called underdamped and the
condition is referred to underdamping (Fig. 9.5). It delays in taking the
reading.

Fig. 9.5 Graphical representation of damping torque

Overdamping: When the damping torque provided in an indicating
instrument is such that the pointer rises slowly and takes sufficient time
to reach its final position, the instrument is called overdamped and the
condition is referred to overdamping (Fig. 9.5). It makes the instrument
sluggish.
Critical damping: When the damping torque provided in an
indicating instrument is such that the pointer rises quickly and obtains
its final position immediately, the instrument is called critically
damped and the condition is referred to critical damping (Fig. 9.5). This
is what we require in indicating instruments.

9.4 METHODS OF PROVIDING CONTROLLING TORQUE

The controlling or restoring or balancing torque is provided in the

indicating instruments by two methods, namely spring control and gravity
control.

9.4.1 Spring Control

In this method, two phosphor bronze spiral hair-springs A and B are

attached to the moving system (spindle) of the indicating instrument as
shown in Figure 9.6(a). However, only one spring is used in moving iron
instruments. In fact, one end of each spring is attached with the spindle and
the other end is attached to some fixed point (may be outer frame or body
of the instrument). The two springs are wound in opposite direction to
compensate for change in temperature. The moving system is statically
balanced in all positions by providing balancing weights as shown in Figure
9.6(a). To adjust the zero of the pointer, an arrangement, called zero
adjuster is provided on the pointer as shown in Figure 9.6(b).
Fig. 9.6 Spring control to provide controlling torque (a) Two springs
attached to the spindle in opposite direction (b) Pointer with zero adjuster

Under ordinary conditions, when instrument is not in use, the two springs
are in their natural position, the controlling torque is zero and the pointer is
at zero position. When the instrument is connected in the circuit, deflecting
torque (Td) deflects the pointer. With the deflection of the pointer, one of
the springs is unwound, while the other gets twisted. The resultant twist in
the springs provides controlling torque (Tc) that is directly proportional to
the angle of deflection θ of the moving system, that is, T ∝ θ. The pointer
comes to the position of rest when controlling torque is equal to deflecting
torque, that is,Tc = Td.

If

Td ∝ I (in the case of permanent magnet moving coil instrument), then

I ∝ θ (since Tc ∝ θ and Td = Tc)

Hence, in spring-controlled instruments (only in which Td ∝ I), scales are

uniform.

Important points for consideration

The spring should have a fairly large number of turns so that the
deformation per unit length is kept small on full-scale deflection. Moreover,
it also ensures that controlling torque is proportional to the angle of
deflection. However, the stress in spring should be limited to such a value
that there is no permanent set in it.

Advantages

1. When controlling torque is provided by spring, the instrument can be placed in

any position.
2. The hair spring has almost negligible weight, and therefore, practically there is
no increase in weight of the moving system.
3. Spring-controlled instruments (only in which Td ∝ I) have uniform scales.

Disadvantages

1. The change in temperature affects the length of spring, and hence, the
controlling torque.
2. Since the springs are very delicate, the accidental stresses may damage them.
3. Due to fatigue, springs deteriorate with time.

9.4.2 Gravity Control

In this method, a small adjustable weight W is attached to the moving

system in such a way that it produces a controlling torque when the moving
system is in deflected position. The controlling torque can be varied by
adjusting the position of the control weight upon the arm as shown
in Figure 9.7(a).

At zero position of the pointer, the control weight W is in the vertical

position, and therefore, no controlling torque is produced. However, under
the action of deflecting torque, the pointer is deflected through an
angle θ from its zero position, as shown in Figure 9.4(a) (dotted position).
Due to gravity, the control weight would try to come back to its original
(i.e., vertical) position and produces controlling torque. Under the
stationary position, controlling torque must be equal to deflecting torque
(i.e., Tc = Td).

Let,

W = control weight,

Fig. 9.7 Gravity control to provide controlling torque (a) Position of

pointer with and without deflection (b) Forces acting on weight at deflected
position
l = distance of control weight from axis of rotation and
θ = angle through which pointer or weight has deflected.
In the deflected position, weight W can be resolved into two components,
that is, W cosθ and W sinθ. Only the component W sinθ provides the
controlling torque.
Tc = Wl sinθ
or

Tc ∝ sinθ (since W and l have fixed values)

If

Td ∝ I, then

I ∝ sinθ (Td = Tc at the position of rest)

Hence, in gravity-controlled instruments, scales are not uniform, but are
crowded in the beginning.

Advantages

1. It is very cheap.
2. It is a very simple method.
3. It is not affected by change in temperature.
4. It is free from fatigue and does not deteriorate with time.
5. The controlling torque can be varied easily.

Disadvantages

1. The instruments in which controlling torque is provided, with gravity control

method, have non-uniform scales.
2. The instrument has to be kept in vertical position.
3. The control weight adds to the weight of the moving system that decreases
torque or weight ratio and reduces the sensitivity of the instrument.

9.5 METHODS OF PROVIDING DAMPING TORQUE

To obtain critical damping (i.e., the value of damping that is sufficient to
enable the point to rise quickly to its deflected position without
overshooting), adjustments are made while designing the instruments.
Damping torque or force can be provided by the following methods.

9.5.1 Air Friction Damping

Two methods of air friction damping are illustrated in Figure

9.8(a) and (b). In the first case, a light aluminium piston, and in the second
case, a vane is attached to the moving system. The piston (or vane) attached
to the spindle moves in an air chamber, having cross-section either circular
or rectangular, closed at one end.

Fig. 9.8 Air friction damping (a) Air friction damping due to movement of
piston in a cylinder (b) Air friction damping due to movement of vane in a
chamber

The clearance between the piston and the sides of the chamber should be
very small and uniform. When the pointer is deflected upscale to read the
quantity to be measured, the piston moves out of the chamber, so that the
pressure in the closed space S falls. The pressure on the open side of the
piston is greater than the closed space that opposes the motion. Thus, the
arrangement restricts the quick movement of the pointer and does not
allow it to overshoot from its final position. However, if the pointer
overshoots slightly, it has to come back. In this case, the piston is pushed
into the air chamber compressing the air in the closed space S. This
increases the pressure in the closed space that restricts the movement of
the piston, and thus, opposes the rapid downward movement of the
pointer. Hence, the necessary damping is produced and pointer comes to
rest at its final position quickly.

9.5.2 Fluid Friction Damping

In this method of damping, light disc or vanes are attached to the spindle of
the moving system and dipped into a pot of damping oil as shown in Figure
9.9(a) and (b). The motion of the moving system is always opposed by the
friction of the damping oil on the vanes. The damping force acting on the
vanes increases with the increase in the speed of the moving system. The
damping force always acts in opposite direction to that of rotation and is
zero when the vanes are stationary.

Fig. 9.9 Fluid friction damping (a) Side view (b) Top view

In this method of damping, no care is required as in the air friction

damping. However, this method is not suitable for portable instruments
because of oil contained in the instrument may leak through it. The other
disadvantages of this method are creeping of oil and the necessity of using
the instrument always in the vertical position.

9.5.3 Eddy Current Damping

In this method of damping, when the sheet of conducting but non-magnetic
material such as copper or aluminum moves in a magnetic field so as to cut
through magnetic lines of force, eddy currents are induced in the sheet and
a force exists between these currents and the magnetic field. This force
always acts in opposite direction to that of the cause producing it, that is,
motion, according to Lenz’s law. This provides necessary damping torque.
The magnitude of damping torque is directly proportional to the speed of
the moving system.

Two methods of eddy current damping are shown in Figure 9.10. In Figure
9.10, a thin aluminum disc, mounted on the spindle carrying the pointer of
the instrument, is allowed to rotate in the air gap of a damping magnet
(permanent); when the spindle rotates, disc cuts through the magnetic lines
of force and eddy currents are induced in it. Thus, a force acts on the disc
that opposes the motion and provides the necessary damping torque.

Fig. 9.10 Eddy-current damping (a) Eddy-current damping for disc (b)
Eddy-current damping in an aluminum former

Figure 9.10(b) shows the 1eddy current damping employed in permanent-

magnet moving coil instruments. The operating coil (coil that produces
deflecting torque) is wound on a thin light aluminium former to which
pointer is attached. When the coil wound on the former moves in the field
of the permanent magnet, eddy currents are induced in the aluminium
former. Thus, a force acts on the former that opposes the motion and
provides the necessary damping.

Differentiation of indicating and integrating instruments is given in Table

9.2.
Table 9.2 Difference Between Indicating and Integrating
Instruments

S.N
Indicating instruments Integrating instruments
o.

These instruments indicate the ma These instruments add up the el

gnitude of ectrical quantity
1
electrical quantity being measured and measure the total quantity i
instantaneously. n a given period.

Controlling torque is provided in t No controlling torque is provide

2
hese instruments. d in these instruments.

These instruments are equipped w In these instruments, damping

3
ith damping torque. torque is not required.

In these instruments, registering In these instruments, registerin

4
mechanism is not required. g mechanism is provided.

Example 9.1

It is found that 10 A current passes through a resistor of 10 Ω value. The

resistor has 5% tolerance. The error in measurement of current can be as
high as 5%. What is the maximum error in the measurement of power
calculated from the measured value of current and the nominal value of
resistor?

(U.P.T.U. Tut.)

Solution:

Power dissipated in the resistor P = I2R

The limiting error in power dissipation = 2 × 5 + 5 = 15%

Hence, power dissipation, P = I2R = 102 × 10 = 1000 W ± 15%, that is, 1000
± 150 W
Thus, the maximum error that crop-up during measuring power while
calculated from the measured value of current and nominal value of resistor
is ± 150 W.

PRACTICE EXERCISES

Short Answer Questions

1. What do you mean by measurements?

2. What do you mean by an instrument? How will you classify them?
3. What do you mean by electrical instruments?
4. How will you classify the instruments on the basis of measurements?
5. What are various types of secondary instruments?
6. What effects are used to obtain deflecting torque in electrical instrument?
7. What are essentials of indicating instruments?
8. What do you mean by deflecting torque?
9. What is controlling torque in indicating instruments?
10. What do you understand by damping torque?
11. How controlling torque is provided in indicating instruments?
12. How damping torque is provided in indicating instruments?

Test Questions

1. Name the electrical quantities need to be measured.

2. Give the various types of electrical measuring instruments with examples.
3. Give one example of an integrating instrument.
4. Give one example of recording-type instrument.
5. What is the maximum value of power factor?
6. Differentiate between indicating and recording-type instruments.
7. Differentiate between indicating and integrating-type instruments.
8. How will you differentiate between indicating and integrating instruments?
Give examples for both.
9. Explain briefly how reading is shown by indicating-, integrating-, and
recording-type instruments. Name each type of instrument also.
10. Explain the role of deflecting and controlling torque in an indicating
instrument.
11. Explain the various methods of providing controlling torque in indicating
instruments.
12. What is the role of damping torque? Explain.
13. What are the various methods for providing damping torque in an instrument?
 9.6 MEASURING ERRORS

Measurement is essentially an act by which a comparison is made between

a given quantity and a quantity of the same kind chosen as a unit of
measurement, that is, standard quantity. To make this comparison, a device
is used called measuring instrument. When an unknown quantity is
measured, the value thus obtained is considered to be a true value but it is
seldom true. There is always some difference between the measured value
and the true or exact value of the unknown quantity.

The difference between the measured value (Am) and the actual or true
value A of the unknown quantity is called absolute error of measurement
(δA).

i.e.,

ε0 = δ A = Am – A
The absolute value of error δA does not indicate precisely the accuracy of
measurement. For example, while measuring the circumference of earth if
the absolute error is 1 cm, it is considered to be negligible; however, if this
error occurs while measuring the circumference of a cricket ball, then it is
quite significant. Therefore, it is preferred to represent the error in terms of
relative error than to represent in absolute form.

9.6.1 Relative Error

The ratio of absolute error to the true value of quantity to be measured is

termed as relative error.

i.e.,

When the absolute error ε0 or δA is negligible, that is, when the difference
between measured value Amand true value A is negligible, then relative
error may be expressed as
The relative error may be represented as a fraction or as a percentage.

i.e.,

9.7 ERRORS COMMON TO ALL TYPES OF INSTRUMENTS

The errors that are common to all types of instruments are given as follows:

1. Temperature error: Apart from room temperature, the rise in temperature

occurs due to the heating effect of current flowing through the operating coil.
This causes the change in resistance of the working coil and resistance of the
other resistors connected in the instrument. Consequently, an erroneous
reading is obtained while measuring an electrical quantity. Such an error is not
serious in the case of ammeters, but it causes serious effect in the case of
voltmeters. This error can be reduced by providing sufficient ventilation and
cooling. This error can be further minimised by providing a series resistance
coil of material having very small temperature co-efficient of resistance and
working coil is made of copper wire.
2. Friction error: When deflecting torque occurs, the spindle of the moving
system pivoted in the jewel bearing rotates and this causes friction; in this
manner, it affects the instrument reading and hence it is called friction error.
This error is more prominent when the deflecting torque is very small. To
minimise this error, a moving system of light weight is designed.
3. Observational error: This error is usually due to misreading of the scale. It
can be minimised by placing parallax mirror with the scale and using it
effectively.

9.8 MOVING IRON INSTRUMENTS

These instruments are quite cheap in cost, simple in construction, and

reasonably accurate at fixed power supply frequency. These instruments
can be used both on AC and DC. Therefore, these are widely used in
laboratories and on switching panels. These instruments are used either as
voltmeter or ammeter only. The pictorial view of these instruments is
shown in Figures 9.11 and 9.12, respectively.

Fig. 9.11 Voltmeter

Fig. 9.12 Ammeter

Moving iron instruments are of two types, namely attraction type and
repulsion type.

9.8.1 Attraction-type Moving Iron Instruments

Principle

The basic principle of an attraction-type moving iron instrument is

illustrated in Figure 9.13. When a soft iron piece (or vane) is placed in the
magnetic field of a current-carrying coil, it is attracted towards the centre of
the coil. This is because the piece tries to occupy a position of minimum
reluctance. Thus, a force of attraction is exerted on the soft iron piece and
deflection in the needle takes place. Hence, the name attraction-type
moving iron instrument.

Fig. 9.13 Attraction type moving-iron instruments

Construction

The sectional view of an attraction-type moving iron instrument is shown

in Figures 9.14 and 9.15. It consists of a stationary hollow cylindrical coil.
An oval-shaped soft iron piece is mounted eccentrically to the spindle to
which a pointer (needle) is attached. The controlling torque is provided by
spring control method while damping torque is provided by air friction, as
shown in Figures 9.14 and 9.15.

Working

When the instrument is connected in the circuit, an operating current (i.e.,

current to be measured in ammeter and current proportional to voltage to
be measured in voltmeter) flows through the stationary coil. A magnetic
field is set up and the soft iron piece is magnetized that is attracted towards
the centre of the coil, as shown in Figure 9.13. Thus, the pointer attached to
the spindle is deflected over the calibrated scale.

If current in the coil is reversed, the direction of magnetic field produced by

the coil will reverse. In turn, this will also reverse the magnetism produced
in the soft iron piece. Hence, the direction of deflecting torque remains
unchanged. Thus, these instruments can be used on DC as well as on AC
system.

Fig. 9.14 Sectional view of attraction type moving iron instrument

Deflecting torque

The deflecting torque Td depends upon the force acting on the soft iron
piece. Let

H = field strength produced by the coil;

m = pole strength of the soft iron piece, and (m ∝ H)

Pulling force acting on the movable iron piece,

F ∝ m × H or F ∝ H2

Now, H ∝ I

F ∝ I2

As deflecting torque, Td ∝ F

Td ∝ I2
The controlling torque Tc is provided by the spiral spring

Tc ∝ θ (where θ is angle of deflection)

In steady position of deflection, Tc = Td

θ ∞ I2 (I is the rms value of current in AC)

Since deflection θ ∝ I2, the scale of such an instrument is non-uniform,

being crowded in the beginning. However, by choosing proper dimensions,
shape and position of soft iron piece (vane), it is possible to design and
construct an instrument with a scale that is very nearly uniform over a
considerable part of its length.
Fig. 9.15 Attraction type moving iron instrument with air friction
damping

9.8.2 Repulsion-type Moving Iron Instruments

Principle

The basic principle of a repulsion-type moving iron instrument is that the

repulsive forces will act between two similarly magnetised iron pieces when
placed near to each other.

Construction

The sectional view of such an instrument is shown in Figure 9.16. It consists

of a fixed cylindrical hollow coil that carries the operating current. Inside
the coil, there are two soft iron pieces (rods or vanes) placed parallel to each
other and along the axis of the coil. One of the rod or vane is fixed and the
other is movable connected to the spindle. A pointer is attached to the
spindle that gives deflection on the scale. The controlling torque is provided
by spring control method, while damping torque is provided by air friction,
as shown in Figure 9.16.
Fig. 9.16 Sectional view of repulsion type moving iron instrument (b) Top
view of repulsion type moving iron instrument

Working

When the instrument is connected in the circuit, the operating current

flows through the coil. A magnetic field is set up along the axis of the coil.
This field magnetises both the iron pieces, and therefore, both the pieces
attain similar polarities. A force of repulsion acts between the two;
therefore, movable piece moves away from the fixed piece. Thus, the
pointer attached to the spindle deflects over the calibrated scale.
If current in the coil is reversed, the direction of magnetic field produced by
the coil is reversed. Although the polarity of the magnetised soft iron pieces
is reversed but still they are magnetised similarly and repel each other.
Hence, the direction of deflecting torque remains unchanged. Thus, these
instruments can be used on DC as well as on AC system.

Deflecting torque

The deflecting torque depends upon the repulsive force acting between the
similarly magnetised iron pieces. Let,

H = field strength produced by the coil;

m1 = pole strength of the fixed iron piece; (m1 ∝ H)

m2 = pole strength of the movable iron piece; (m2 ∝ H)

∴ Repulsive force acting on the movable iron piece,

F ∝ m1m2 or F ∝ H2;
Now,

H∝I

F ∝ I2

As deflecting torque, Td ∝ F
∴

Td ∝ I2
The controlling torque Tc is provided by the spring

Tc ∝ θ (where θ is angle of deflection)

At steady position of deflection, Tc ∝ Td

θ ∝ I2 (I is the rms value of current in AC)

Since deflection θ ∝ I2, and therefore, the scale of such an instrument is

non-uniform, being crowded in the beginning. However, by using tongue-
shaped iron pieces, scale of such instruments can be made almost uniform.

9.8.3 Advantages and Disadvantages of Moving Iron Instruments

Advantages

1. They are cheap in cost, mechanically robust, and simple in construction.

2. They can be used on both AC and DC.
3. They are reasonably accurate.
4. They possess high operating torque.
5. They can withstand overloads momentarily.

Disadvantages

1. They cannot be calibrated with a high degree of precision with DC on account

of the effect of hysteresis in the iron rods or vanes.
2. They have non-uniform scale crowded at the beginning, and therefore, it is
difficult to get accurate readings at this end.
 3. They are not very sensitive.
4. Power consumption is quite high.
5. Errors are introduced due to change in frequency in the case of AC
measurements.

9.8.4 Errors in Moving Iron Instruments

There are two types of errors that occur in moving iron instruments:

Errors with both DC and AC

The following errors may occur in moving iron instruments when these are
used either on DC or AC.

1. Error due to hysteresis: Because of hysteresis in the iron parts of operating

system, the readings are higher for descending value but lower for ascending
values. The errors due to hysteresis are considerably reduced by using Mumetal
or Permalloy that have negligible hysteresis loss.
2. Error due to stray magnetic fields: Since the operating magnetic field of
these instruments is comparatively weak, and therefore, stray fields (fields
other than the operating magnetic field) affect these instruments considerably.
Thus, the stray fields cause serious errors. These errors can be minimised by
using an iron case or a thin iron shield over the working parts.
3. Error due to temperature: In moving iron instruments, the change in
temperature affects mainly the temperature coefficient of spring. With the
change in temperature, stiffness of the spring varies that causes errors.
However, for voltmeters both the temperature co-efficient of spring and
temperature co-efficient of resistance of voltmeter circuit may balance each
other.

However, in the case of shunt connected instruments, it is observed that the

uncompensated instruments tend to read low by approximately 0.2%/ºC
rise in temperature. Temperature compensation may be affected by
connecting a resistor called the swamping resistor in series with the moving
coil. The swamp resistor is made of Manganin combined with copper in the
ratio of 20:1 to 30:1, which is hardly affected by temperature variations.
The total resistance of the moving coil and swamping resistor increases
slightly with a rise in temperature, but only just enough to overcome the
effect of springs and magnets, so that the overall temperature effect is zero.

Errors with AC only

Error due to change in frequency

The change in frequency produces change in impedance of the coil and

change in magnitude of eddy currents. The increase in impedance of the
coil with the increase in frequency causes serious errors in the case of
voltmeters only. However, this error can be eliminated by connecting a
condenser of suitable value in parallel with the swamp resistance ‘r’ of the
instrument. The impedance of the whole circuit of the instrument becomes
independent of frequency if C = L/r2, where C is the capacitance of the
condenser.

Ranges

1. Ammeters: From about 0-20 mA to 0-800, maximum without current

transformer.
2. Voltmeters: From about 0-1V to 0-800 V, maximum without potential
transformer.

9.8.5 Applications of Moving Iron Instruments

The moving iron instruments are used as ammeters and voltmeters only.
These instruments can work on both AC and DC system.

Ammeter

An instrument that is used to measure electric current in an electric circuit

is called an ammeter. An ammeter is connected in series with the circuit or
load whose current is to be measured (Fig. 9.17). The operating coil of the
instrument is to carry the whole of the current to be measured or fraction of
it. When current flows through the operating coil, the desired deflecting
torque is produced. Since an ammeter is connected in series, it should have
low resistance to keep the circuit conditions to be the same. Hence, the
operating coil of an ammeter should have a few turns of thick wire.
Fig. 9.17 Ammeter connected in series
Voltmeter

An instrument that is used to measure potential difference (or voltage)

across the load or between two points in a circuit is called a voltmeter. A
voltmeter is always connected in parallel with the load or portion of the
circuit whose voltage is to be measured (Fig. 9.18). The deflection of the
meter depends upon the current (Iv) flowing through the operating coil that
is proportional to the voltage across the meter (Iv ∞ V). Since a voltmeter is
connected in parallel, it should have high resistance to keep the
circuit2 conditions to be the same. Hence, the operating coil of a voltmeter
should have a large number of turns of thin wire. However, it is not
sufficient, and therefore, a high resistance is connected in series with the
operating coil (Fig. 9.18).

Fig. 9.18 Voltmeter connected in parallel

Example 9.2
A moving iron instrument gives full-scale deflection with 100 V. It has a coil
of 20,000 turns and a resistance of 2,000 Ω. If the instrument is to be used
as an ammeter to give full-scale deflection at 2 A, calculate the necessary
number of turns in the coil.

Solution:

Full-scale deflection current,

In moving iron instruments, the strength of magnetic field (and hence,

deflecting torque) depends upon AT of the operating coil.

∴ Full-scale deflection AT = NI = 20,000 × 0.05 = 1,000 AT

∴ Turns required to

measure

Learning outcome: The magnitude of deflecting torque depends upon the

magnetic strength provided by the operating coil that further depends upon
AT (NI) of the coil (the larger the amount, the smaller is the number of
turns for required flux).

Example 9.3

The coil of a 250 V moving iron voltmeter has a resistance of 500 Ω and an
inductance of 1 H. The current taken by the instrument when placed on 250
V, DC supply is 0.05 A. Determine the percentage error when the
instrument is placed on 250 V, 100 Hz AC supply.

Solution:

Resistance of voltmeter coil, R = 500 Ω

Inductance of voltmeter coil, L = 1 H

Current taken by the instrument when placed on 250 V DC

Idc = 0.05 A

Total ohmic resistance

∴ Series swamp resistance, r = 5,000 − 500 = 4,500 Ω

When the instrument is placed on 250 V, 100 Hz AC

Inductive reactance of the coil, XL = 2πfL = 2π × 100 × 1 = 628.32 Ω

Impedance of the coil,

Current flowing through the coil,

Deflection or voltmeter reading with this

current

Percentage error

Learning outcome: If moving iron instruments are calibrated on DC, they

will not read accurately on AC if some compensation is not provided.
Hence, an error crops in.

Example 9.4

An AC voltmeter with a maximum scale reading of 50 V has an inductance

of 0.09 H and a total resistance of 500 Ω. The coil is wound with copper
wire having a resistance of 50 Ω and the remainder of the voltmeter circuit
consists of nine non-inductive resistances in series with the coil. Find the
capacitance that should be placed across the non-inductive resistor to make
the instrument read correctly both on DC as well as on AC.

Solution:
Total resistance, RE = 500 Ω; coil resistance, RC = 50 Ω

swamp resistance, r = RE – RC = 500 – 50 = 450 Ω; inductance, L = 0.09 H

Capacitance required to be connected in parallel with the swamp resistance

to make the instrument independent of frequency.

Learning outcome: The frequency error in moving iron instruments can be

eliminated by providing a suitable capacitor in parallel with the swamp
resistance.

9.9 PERMANENT MAGNET MOVING COIL INSTRUMENTS

These instruments are very sensitive and accurate. These can be used only
on DC as voltmeter and ammeter. The pictorial view of a voltmeter and
ammeter is shown in Figures 9.19 and 9.20, respectively. The scale of such
instruments is uniform, as shown in the Figure 9.20.

Fig. 9.19 Voltmeter

Fig. 9.20 Ammeter

9.9.1 Principle

The basic principle of permanent magnet-type moving coil instrument is

that when a current-carrying conductor is placed in a magnetic field, a
mechanical force is exerted on the conductor, as shown in Figure 9.21. The
basic principle can also be stated that when a field Fr produced by the
movable current-carrying coil tries to come in line with the main field Fm, a
deflecting torque is developed as shown in Figure 9.22. Due to the
production of deflecting torque, the pointer deflects over the scale.

Fig. 9.21 Force exerted on a current carrying conductor placed in

magnetic field
Fig. 9.22 Torque development by the alignment of two fields

9.9.2 Construction

The simple view of permanent magnet-type moving coil instrument is

shown in Figure 9.23. It consists of a powerful permanent shoe magnet, a
light rectangular coil of many turns of fine wire wound on a light
aluminium former and a cylindrical iron core (a stationary part) inserted
in between the coil sides to reduce reluctance for the magnetic lines of
force. The coil is mounted on the spindle and acts as the moving element.
Two phosphor bronze spiral hair springs are attached to the spindle. The
springs provide the controlling torque as well as they act as incoming and
outgoing leads for the current. Eddy current damping is provided by the
aluminium former over which the operating coil is wound.
Fig. 9.23 (a) Parts of PMMC Instrument (b) Eddy current damping in
PMMC instrument

9.9.3 Working

When the instrument is connected in the circuit, a current flows through

the operating coil mounted on the spindle. Since the coil is placed in the
strong magnetic field of permanent magnets, a force is exerted on the
current-carrying conductors of the coil that produces deflecting torque.
Thus, the pointer attached to the spindle deflects over the calibrated scale.

If current in the coil is reversed, the direction of deflecting torque will also
be reversed because field produced by the permanent magnets does not
change. This will give an opposite direction of rotation. Thus, the
instrument cannot be used on AC, and it can only be used on DC.

9.9.4 Deflecting Torque

The deflecting torque Td depends upon the force acting on the coil sides.

Let

B = flux density in tesla in the air gap;

l = effective length of each coil side in metre;
N = number of turns of the coil;
r = distance in metre between centre of the coil and force;
I = current flowing through the coil in ampere;
Force acting on each coil side,

F = BIlN N
Deflecting torque,

Td = 2Fr = 2BIlNr Nm
Since all other quantities are constant, except I

Td ∝ I
The controlling torque is provided by the springs

Tc ∝ θ (where θ is angle of deflection)

At steady position of deflection,

Tc = Td;

θ∝I
Since deflection θ is proportional to the operating current flowing through
the coil, and therefore, the scale of such instruments is uniform.

9.9.5 Advantages and Disadvantages of Permanent Magnet Moving Coil

Instruments

Advantages

1. These instruments have uniform scale.

2. Very effective; the reliable eddy current damping is provided.
3. No hysteresis loss, as the former is of aluminium.
4. Low power consumption because driving power is small.
5. No effect of stray magnetic field, as working field provided by the permanent
magnets is very strong.
 6. High torque or weight ratio, and therefore, such instruments require small
operating current and are very sensitive.
7. These instruments are very accurate and reliable.

Disadvantages

1. These instruments cannot be used for AC measurements.

2. These are costlier in comparison to moving iron instruments.
3. Friction and temperature might introduce some error.
4. Some errors are also caused due to ageing of control springs and permanent
magnets.

9.9.6 Errors in Permanent Magnet Moving Coil Instruments

The main sources of errors in these instruments are due to the following:

1. Weakening of stiffness of springs due to ageing and rise in temperature.

2. Weakening of field produced by permanent magnet due to ageing and
temperature effects.
3. Change in resistance of the moving coil with temperature.

However, these errors are negligibly small and as such these instruments
are considered to be most accurate for measuring currents and voltages in
DC circuits.

9.9.7 Range

DC Ammeters

1. Without shunt (i.e., instrument alone) 0–5 μA to 0 50 μA

2. Without internal shunts up to 0–200 A
3. With external shunts, up to 0–5000 A

DC Voltmeters

1. Without series resistance or multiplier (i.e., instrument alone) 0–50 mV

2. With series resistance, up to 0–3,000 V

Example 9.5

In a moving coil instrument, the moving coil consists of 300 turns wound
on a former of dimension 3 cm × 2 cm. The flux density in the air gap is
0.05 T. Determine the turning moment on the coil when carrying a current
of 10 mA.

Solution:

Deflecting force, F = BIlN

where

N = 300; l = 0.03 m; B = 0.05 T;

I = 10 × 10–3 A; r = 2/2 = 1 cm = 0.01 m

F = 0.05 × 10 × 10–3 × 0.03 × 300 = 4.5 × 10–3 N

Turning moment on the coil, Td = 2F × r = 2 × 4.5 × 10–3 × 0.01

= 9 × 10–5 Nm
Example 9.6

In a moving coil instrument, the moving coil consists of 100 turns wound
on a square former of length 3 cm. The flux density in the air gap is 0.06 T.
Calculate the turning moment acting on the coil when carrying a current of
12 mA.

(U.P.T.U.)

Solution:

Number of turns on the coil, N = 100

Length of former, l = 3 cm = 0.03 m

Width of former, W = 3 cm = 0.03 m

Radius for the turning,

Field strength, B = 0.06 T

Current flowing through the coil, i = 12 mA = 0.012 A

Turning moment or deflecting torque, Td = 2 Bil N × r

= 2 × 0.06 × 0.012 × 0.03 × 100 × 0.015

= 6.48 × 10–5 Nm
Example 9.7

A moving coil comprises 100 turns of insulate copper wire wound on a

former of length 3 cm and breadth 4 cm. The resistance of the coil is 2,000
Ω. The field strength of the magnets is 0.06 T. The torque exerted by the
control spring is 0.02 × 10–4 kgm/degree. Estimate the deflection of the
instrument when a voltage of 120 V is applied across it.

Solution:

Number of turns of the coil, N = 100

Mean length of the coil, l = 3 cm = 0.03 m

Radius of the coil,

Flux density, B = 0.06 T

Current through the coil,

Deflecting force, F = BIlN = 0.06 × 0.06 × 0.03 × 100 = 0.0108 N

Deflecting torque, Td = 2Fr = 2 × 0.0108 × 0.02 = 4.32 × 10–4 Nm

Controlling torque/degree = 0.02 × 10–4 kgm = 0.02 × 10–4 × 9.81 Nm

Tc/θ = 0.1962 × 10–4 Nm/degree

Now,

∴ Deflection,

Example 9.8

A moving coil instrument has the following data:

number of turns = 100; width of coil = 20 mm; depth of coil = 30 mm;

flux density in the gap = 0.1 Wb/m2

Calculate the deflecting torque when carrying a current of 10 mA. Further,

calculate the deflection if the control spring constant is 2 × 10–6 Nm/degree.

Solution:

Here, N = 100; l = 30 mm = 0.03 m; = 10 mm = 0.01 m

B = 0.1 Wb/m2; I = 10 mA = 10 × 10–3 A

Tc/θ = 2 × 10–6 Nm/degree

Now,

F = BIlN = 0.1 × 10 × 10–3 × 0.03 × 100 = 3 × 10–3 N

Td = 2F × r = 2 × 3 × 10–3 × 0.01 = 0.06 × 10–3 Nm

∴ Deflection,

Example 9.9

A moving coil millivoltmeter has a resistance of 200 Ω and the full-scale

deflection is reached when a potential difference of 100 mV is applied
across the terminals. The moving coil has effective dimensions of 30 mm ×
25 mm and is wound with 100 turns. The flux density of the gap is 0.2
Wb/m2. Determine the control constant of the spring, if the final deflection
is 100°.

(U.P.T.U.)

Solution:

Here, Rm = 200 Ω; V = 100 mV; l = 30 mm = 30 × 10–3 m;

N = 100; B = 0.2 Wb/m2; θ = 100°

Full-scale deflection current,

= 0.5 mA = 0.5 × 10–3 A

Deflecting torque, Td = 2 BilrN = 2 × 0.2 × 0.5 × 10–3 × 30 × 10–3 × 12.5 × 10–
3 × 100
= 75 × 10–7 Nm
Full-scale deflection, θ = 100°

Control constant of spring =

9.10 DIFFERENCE BETWEEN AMMETER AND VOLTMETER

There is no fundamental difference in the operating principles of ammeters

and voltmeters. Both are current operated devices (except electrostatic-type
voltmeters), that is, deflecting torque is produced when current flows
through their operating coils. In an ammeter, the deflecting torque is
produced by current to be measured or by a definite fraction of it, whereas
in a voltmeter, torque is produced by the current proportional to the voltage
to be measured. Thus, the real difference between the two instruments is in
the magnitude of the current producing the deflecting torque. The essential
requirements of a measuring instrument are that its introduction into the
circuit, where measurements are to be made, does not alter the circuit
conditions and the power consumed by them for their operation should be
very small.

An ammeter is connected in series with the circuit whose current is to be

measured. Therefore, it should have a low resistance. On the other hand, a
voltmeter is connected in parallel with the circuit whose voltage is to be
measured, and therefore, it must have high resistance. Thus, we conclude
that the difference is only in the resistance of the instrument; in fact, an
ammeter can be converted into voltmeter by connecting a high resistance in
series with it. Similarly, a voltmeter can be converted into an ammeter by
connecting a shunt across the voltmeter.

Example 9.10

A meter has a full-scale angle of 90° at a current of 1 A. This meter has

perfect square-law response. What is the current when the deflection angle
is 45°? Draw the conclusion.

(U.P.T.U.)
Solution:

Here, I1 = 1 A; θ1 = 90°, θ2 = 45°

Since,

θαI2,

or

Learning outcome: The result shows that when deflection is reduced to

half, the current flowing through the meter is not reduced to half, it is
70.7% of the previous value. In meters that follows the square law, the scale
is not uniform.

Example 9.11

Two voltmeters one with a full-scale reading of 100 V and another with a
full-scale reading of 200 V are connected in series across a 100 V supply.
The internal resistance of both meters is the same. What are the readings?

(U.P.T.U.)

Solution:

Two voltmeters connected in series are shown in Figure 9.24.

Fig. 9.24 Circuit diagram

Let the resistance of each voltmeter be R Ω

Total resistance,

Rt = R + R = 2R
When 100 V is applied across the series combination,

Current,

Potential difference across voltmeter V1 or the reading of voltmeter V1,

Potential difference across voltmeter V2 or the reading of voltmeter V2,

Example 9.12

Two voltmeters have the range 0–400 V. The internal impedances are
30,000 Ω and 20,000 Ω. If they are connected in series and 600 V be
applied across them, what will be their readings?

(U.P.T.U.)
Solution:

Total resistance when the two voltmeters are connected in series, as shown
in Figure 9.25.

Fig. 9.25 Two voltmeters connected in series

Rt = 30,000 + 20,000 = 50,000 Ω
When 600 V is applied across the series combination,

Current,

A Potential difference across voltmeter V1 or the reading of voltmeter V1,

= IR1 = 1.2 × 10–2 × 30,000 = 360 V.

Potential difference across voltmeter V2 or the reading of voltmeter V2,

= IR2 = 1.2 × 10–2 × 20,000 = 240 V.

Example 9.13

Two ammeters, one with a current scale of 10 A and resistance of 0.01 Ω

and the other with a current scale of 15 A and resistance of 0.005 Ω are
connected in parallel. What can be the maximum current carried by this
parallel combination so that no meter reading goes out of the scale?
(U.P.T.U. Dec. 2003)

Fig. 9.26 Two ammeters connected in parallel

Solution:

Two ammeters connected in parallel are shown in Figure 9.26.

Let the current carried by the parallel combination be I ampere.

Maximum current carried by ammeter A1, that is, I1 = 10 A.

Voltage across the combination, say V1 = I1 Rm1 = 10 × 0.01 = 0.1 V.

Then, current carried by the ammeter A2, that is,

This current is more than the current that can be carried by the second
ammeter, and hence, the proposal is wrong. Now, if the current carried by
the second ammeter A2, that is, I2′ = 15 A

Then, voltage across the combination, say V2 = I2′Rm2 = 15 × 0.05 = 0.075 V

Current carried by the ammeter A1,

This current is less than the current that can be carried by the first
ammeter A1, and hence, the proposal is correct. Total maximum value of
current that can be carried by the combination,
 9.11 EXTENSION OF RANGE OF AMMETERS AND VOLTMETERS

The moving coil instruments can carry maximum current of about 50 mA

safely and the potential drop across the moving coil is about 50 mV.
However, in practice, heavy currents and voltages are required to be
measured. Therefore, it becomes necessary that the current and voltage
being measured be reduced and brought within the range of instrument.

There are four common devices used for extending the range of the
instruments, namely shunts, multipliers, current transformers, and
potential transformers. The extension of range of current and potential
transformers is employed for measurement of very high AC currents and
voltages in power system.

1. Shunts: These are used for the extension of range of ammeters. Shunt is a
resistance of small value, just like a strip, as shown in Figure 9.27, having
minimum temperature co-efficient. It is always connected in parallel with the
ammeter whose range is to be extended. The combination is connected in
series with the circuit whose current is to be measured.

Fig. 9.27 Shunts

2. Multipliers: These are used for the extension of range of voltmeters.

Multiplier is a non-inductive high resistance usually carbon resistors, as shown
in Figure 9.28, connected in series with the instrument whose range is to be
extended. The combination is connected across the circuit whose voltage is to
be measured.
 Fig. 9.28 Carbon resistor

9.11.1 Extension of Ammeter Range

The current range of a DC moving coil ammeter is extended by connecting a

shunt RS (low resistance) across the coil, circuit is shown in Figure 9.29.

Let I = current to be measured.

Im = full-scale deflection current of ammeter;

Is = shunt current;

Rm = resistance of ammeter;

Rs = shunt resistance,

From Figure 9.29, we have, I = Im + Is

or

Is = I – Im and Is Rs = Im Rm or (I – Im) Rs = Im Rm
or

IRs = Im (Rm + Rs)

or
Fig. 9.29 Circuit for extension of ammeter range

The ratio of the total current I to be measured to the full-scale deflection

current Im is known as the multiplying power of the shunt or instrument
constant. It may be denoted by N.

From Equation (i), we get

Hence, for measurement of current N times, the current range of

instrument, the shunt resistance should be times the meter

resistance.

Example 9.14

A moving coil ammeter has a full-scale deflection of 50 μA and a coil

resistance of 1,000 Ω. What will be the value of the shunt resistance
required for the instrument to be converted to read a full-scale reading of 1
A?

(U.P.T.U.)

Solution:

Full-scale deflection current, Im = 50 × 10–6 A

Instrument resistance, Rm = 1000 Ω

Total current to be measured, I = 1 A

Value of shunt resistance

required,

Example 9.15

The full-scale deflection current of an ammeter is 1 mA and its internal

resistance is 100 Ω. If this meter is to have full-scale deflection at 5 A, what
is the value of the shunt resistance to be used?

(U.P.T.U.)

Solution:

Full-scale deflection current, Im = 1 mA = 0.001 A

Instrument resistance, Rm = 100 Ω

Total current to be measured, I = 5 A

Shunt current, Is = I − Im= 5 − 0.001 = 4.999 A

Value of shunt resistance,

Example 9.16

Design a multi-range ammeter with ranges of 1 A, 5 A, 25 A, and 125 A

employing individual shunts in each case. A D’Arsonal movement with coil
internal resistance of 730 Ω and a full-scale current of 5 mA is available.

Solution:

Meter resistance, Rm = 730 Ω

Meter current, Im = 5 mA = 0.005

A Shunt current, Is = I − Im
Shunt resistance,

For 1 A range,

For 5 A range,

For 25 A range,

For 125 A range,

9.11.2 Extension of Voltmeter Range

The voltage range of a DC moving coil voltmeter (instrument) is extended

by connecting a multiplier R(high resistance) in series with the coil. The
circuit is shown in Figure 9.30.

Fig. 9.30 Circuit for extension of voltmeter range

Let V = voltage to be measured;

v = voltage across the meter;

Im = full-scale deflection current of voltmeter;

R = resistance in series with the coil to extend the range;

Rm = voltmeter resistance.

From the circuit shown in Figure 9.30, we have V = Im (R + Rm)

or

Required resistance

From the circuit shown in Figure 9.30, we also get

The ratio of voltage to be measured to the voltage across the voltmeter for
which it is actually designed (i.e., V/v) is known as multiplying factor (m).

Hence, for the measurement of voltage, m times the voltage range of the
instrument the series multiplying resistance R should be (m − 1) times the
meter resistance Rm.

Note: The ammeters or voltmeters used in the laboratories, etc., have shunt
(low resistance) or multipliers (high resistance) incorporated in them,
respectively. The scales are graduated and marked after taking into
consideration the multiplying factor or instrument constant so that the
circuit current or voltage be read directly from the scale.

The following are the disadvantages of using shunts and multipliers for
measuring high currents and voltages:

1. In the case of AC measurements, inductance of the coil is also involved due to

which accurate calibrations cannot be done.
2. It is dangerous to measure high voltages because the operator may come in
contact with live leads accidently.
3. Shunts and multipliers do not give a straight line relation between the
instrument current and the current in the shunts and multipliers in AC
measurements.

Example 9.17

The full-scale deflection current of a meter is 1 mA and its internal

resistance is 100 Ω. If this meter is to have full-scale deflection when 100 V
is measured. What should be the value of series resistor?

(U.P.T.U.)

Solution:

Instrument resistance, Rm = 100 Ω

Full-scale deflection current, Im = 1 mA = 1 × 10–3 A

Voltage to be measured, V = 100 V

Value of series resistor,

Example 9.18

The electrical lab of a polytechnic has a 0–200 V range voltmeter with

20,000 Ω/V sensitivity. What modifications needed to extend the range of
meter to 0–2,000 V? What should be the power rating of resistor used?

Solution:
Full-scale deflection voltage, v = 200 V

Resistance of meter, Rm = 20,000 × 200 = 4 × 106 Ω

Meter current,

Voltage to be measured, V = 2,000 V

Voltage across series resistor = 2,000 − 200 = 1,800 V

Resistance of the multiplier

Power rating of the resistor = Im2 R = (50 × 10–6)2 × 36 × 106 = 0.09 W.

Example 9.19

A moving coil instrument has a resistance of 5 Ω and gives a full-scale

deflection of 100 mV. Show how the instrument may be used to measure:

(i) voltage up to 50 V (ii) currents up to 10 A.

(U.P.T.U. 2006-07)

Solution:

Instrument’s resistance, Rm = 5 Ω

Full-scale deflection voltage, v = 100 mV

1. Let R be the resistance to be connected in series for increasing the range of

instrument as a voltmeter to 50 V.
Full-scale deflecting current,

Voltage to be measured,

V = Im (Rm + R)
 or

2. Let RS be the resistance of the shunt to be connected in parallel to increase the

range of instrument as ammeter to measure 10 A.

Full-scale deflection current,

Shunt current, IS = I – Im = 10 – 0.02 = 9.98 A

Now, IsRs = ImRm or

Example 9.20

A moving coil milliammeter gives full-scale deflection with 15 mA and has a

resistance of 5 Ω. Calculate the resistance to be connected in (i) parallel to
enable the instrument to read up to 1A and (ii) series to enable it to read up
to 10 V.

(U.P.T.U. July 2002)

Solution:

Here, Rm = 5 Ω

Full-scale deflection current, Im = 15 mA = 15 × 10−3 A

1. Current to be measured, I = 1 A

Multiplying power of shunt,

Let Rs be the resistance connected in parallel to enable the
instrument to read up to 1 A

2. Voltage to be measured, V = 10 V

Let R be the resistance required to be connected in series for full-

scale deflection with 10 V,
Example 9.21

A moving coil instrument having internal resistance of 50 Ω indicates full-

scale deflection with a current of 10 mA. How can it be made to work as (i)
a voltmeter to read 100 V on full-scale and (ii) an ammeter of 1 A on full-
scale?

(U.P.T.U. June 2001)

Solution:

Instrument resistance, Rm = 50 Ω

Full-scale deflection current, Im = 10 m A = 0.01 A

1. Let R be the resistance required to be connected in series with the instrument

to enable it to read 100 V on full-scale. Then,

2. Let Rs be the resistance required to be connected across the instrument

to enable it to read 1 A on full-scale,

Example 9.22

A moving coil instrument has a resistance of 2 Ω and it reads up to 250 V

when a resistance of 5,000 Ω is connected in series with it. Find the current
range of the instrument when it is used as an ammeter with the coil
connected across a shunt resistance of 2 mΩ.

(U.P.T.U. Feb. 2002)

Solution:
Here, Rm = 2 Ω

Current flowing through the instrument for full-scale deflection,

Shunt resistance, Rs = 2 × 10–3 Ω

Current through shunt resistance,

Current range of instrument = Full-scale deflection current

= Im + Is = 0.04998 + 49.98
= 50.02998 A = say 50 A.

PRACTICE EXERCISES
Short Answer Questions

1. Why electrical instruments are widely used to measure electrical and non-
electrical quantities?
2. What do you mean by moving iron instruments? How are they classified?
3. How deflecting, controlling, and damping torque is produced in attraction-type
moving iron instruments?
4. How deflecting, controlling, and damping torque is produced in repulsion-type
moving iron instruments?
5. Mention some important advantages of moving iron instruments.
6. Mention some important disadvantages of moving iron instruments.
7. What are the causes due to which errors occur in moving iron instruments?
8. What are moving coil instruments? How are these classified?
 9. How deflecting, controlling, and damping torques are produced in
PMMC instruments?
10. Mention some major advantages of PMMC instruments.
11. Mention some major disadvantages of PMMC instruments.
12. What are the major causes of errors in PMMC instruments?
13. Is there any difference between an ammeter and a voltmeter?
14. What should be done to extend the range of an ammeter? Mention some
important mathematical relations?
15. What should be done to extend the range of a voltmeter? Mention some
important mathematical relations.

Test Questions

1. Give construction, principle, and working of an instrument that can measure

both AC and DC.

Or

Explain the principle, construction, and working of moving iron

instruments.
2. Describe with neat sketches the principle, construction, and working of moving
iron repulsion-type instruments.
3. Why the scale of moving iron instruments is not uniform?
4. Describe the working of a moving iron instrument with a neat sketch. Describe
the errors to which such an instrument is subjected to. Explain how these
errors can be minimised.
5. Explain the concept of ammeter and voltmeter and difference between them.
6. Explain the construction, working principle, and uses of moving coil
instrument.

Or

Explain construction and principle of operation of a moving coil-

type ammeter.
7. Give merits and demerits of moving coil and moving iron instruments.
8. Give merits, demerits, sources of error, and applications of moving coil
instruments.
9. Are there any instruments that can be used only for DC? Explain the working
for measuring current and voltage.
10. Describe the construction and working of PMMC instrument. Describe the
method of damping used in these instruments.
 11. Differentiate between moving iron ammeter and permanent magnet moving
coil ammeter.
12. How does current range of a PMMC instrument extended with the help of
shunts? Describe the method of reducing errors due to temperature changes in
shunt connected instruments.
13. A millimetre with a resistance of 10 Ω is connected with a shunt of 0.005 Ω.
What will be current flowing through the instrument if it is connected to a
circuit in which a current of 10 A is flowing?
14. Describe methods of extension of range of an ammeter and a voltmeter.
15. Write short note on shunt and multipliers.
16. Explain the disadvantages of shunts and multipliers when used for extension of
range of AC instruments.

Numericals

1. A moving iron instrument gives full-scale deflection with 250 V. It has a coil of
25,000 turns and a resistance of 2,500 Ω. If the instrument is to be used as an
ammeter to give full-scale deflection of 5 A, calculate the necessary number of
turns in the coil.
(Ans. 500)

2. A 10 V moving iron ammeter has a full-scale deflection of 40 mA on DC circuit.

It reads 0.8% low on 50 Hz AC. Hence, calculate the inductance of the
ammeter.
(Ans. 101.27 mH)

3. A 15 V moving iron voltmeter has a resistance of 500 Ω and inductance of 0.12

H. Assuming that this instrument reads correctly on DC, what will be its
reading on AC at 15 V when the frequency is (i) 25 Hz and (ii) 100 Hz?
(A.M.I.E. Nov. 1994) (Ans. 14.99 V, 14.83 V)

4. The coil of 150 V moving iron voltmeter has a resistance of 500 Ω and an
inductance of 0.75 H. The current taken by the instrument when placed on a
150 V DC supply is 0.05 A. Estimate (i) the alteration of the reading between
DC and AC at 100 Hz and (ii) the capacitance of the capacitor necessary to
eliminate this frequency error.
(Ans. −1.2%, 0.12 μF)
5. In a moving coil instrument, the moving coil consists of 300 turns wound on a
former of dimensions 3 cm × 2 cm. The flux density in the air gap is 0.08 T.
Determine the turning moment on the coil when carrying a current of 15 mA.
(July, 1992) (Ans. 2.16 × 10−4 Nm)

6. In a moving coil instrument, the moving coil consists of 400 turns wound on a
square former of length 2 cm. The flux density in the air gap is 400 lines/cm2.
Calculate moment acting on the coil when carrying a current at 8 mA.
(Ans. 512 × 10−7 Nm)

7. In a moving coil instrument, the moving coil consists of 100 turns wound on a
square former of length 3 cm. The flux density in the air gap is 600 lines/cm2.
Calculate the turning moment acting on the coil when carrying a current of 12
mA.
(Ans. 6.48 × 10−5 Nm)

8. A moving iron instrument has a full-scale angle of 120º at a current of 5 A. This

meter has perfect square-law response. What will be the deflection angle when
the current passing through the meter is 2.5 A? Draw the conclusion.
(Ans. 30°)

9. Two ammeters one with full-scale current of 1 mA and internal resistance of

100 Ω, and the other with a full-scale current of 10 mA and internal resistance
of 25 Ω are in parallel. What is the total current these two meters can carry
without any meter reading getting out of scale?
(U.P.T.U.) (Ans. 5 mA)

10. A moving coil ammeter can read up to 1 A has a resistance of 0.02 Ω. How
could this instrument be adopted to read current up to 100 A?
(Ans. 0.000202 Ω)

11. A milliammeter with a resistance of 5 Ω is connected with a shunt of 0.005 Ω.

What will be the current flowing through the instrument, if it is connected to a
circuit in which a current of 10 A is flowing?
(Ans. 9.99 mA)
12. A moving coil meter has resistance of 10 Ω and gives full-scale deflection when
carrying a current of 50 mA. Show how it can be adopted to measure a current
of 100 A.
(Feb. 1994) (Ans. A shunt of 5 mΩ has to be connected in
parallel with the meter)

13. A milliammeter with a resistance of 5 Ω is connected with a shunt of 0.01 Ω.

What will be the current flowing through the instrument, if it is connected to a
circuit in which a current of 5 A is flowing?
(Ans. 9.98 mA)

14. A moving coil instrument gives a full-scale deflection of 10 mA and potential

difference across its terminals is 100 mV. Calculate series resistance for full-
scale deflection corresponding to 10 V.
(Ans. 990 Ω)

15. A moving coil voltmeter reading up to 20 mV has a resistance of 2 Ω. How this

instrument be adopted to read voltage up to 300 V.
(Ans. 29,998 Ω)

16. A moving coil instrument gives a full-scale defection of 20 mA when a potential

difference of 50 mV is applied. Calculate the series resistance to measure 500 V
on full-scale.
(Ans. 24,997.5 Ω)

17. A PMMC instrument gives full-scale reading of 25 mA when a potential

difference across its terminals is 75 mV. Show how it can be used (a) as an
ammeter for the range of 0-100 A and (b) as a voltmeter for the range of 0-750
V. Further, find the multiplying factor of shunt and voltage amplification.
(Ans. 7.502 × 10−4 Ω; 29997 Ω; 4,000; 10,000)

18. A moving coil ammeter reading up to 1 A has a resistance of 0.02 Ω. How could
this instrument be adopted to read (i) voltage up to 250 V and (ii) current up to
10 A.
(Jan. 1993) (Ans. (i) multiplier: 249.98 Ω; (ii) shunt: 2.22 ×
10−3 Ω)
 19. A moving coil instrument gives full-scale deflection with 15 mA and has a
resistance of 5 Ω. Calculate the resistance to be connected (i) in parallel to
enable the instrument to read up to 1 A and (ii) in series to enable it to read up
to 100 V.
(A.M.I.E. May 1974) (Ans. 0.0761 Ω, 6,661.7 Ω)

20. A moving coil instrument gives full-scale reading at 25 mA when a potential

difference across its terminals is 75 mV. Show how it can be used to measure a

current of 100 A and voltage up to 750 V.

(A.M.I.E. Nov. 1969) (Ans. 0.00075 Ω, 29,997 Ω)

21. A dynamometer-type instrument that gives a maximum reading of 20 mA has a

resistance of 5 Ω. Show how it may be used to measure 400 V and 20 A.

(AMIE, Winter 1995) (Ans. 19,995 Ω, 0.005005 Ω)

9.12 DYNAMOMETER-TYPE INSTRUMENTS

These are known as electrodynamics instruments. These are basically

moving coil instruments. In these instruments, the operating field is
produced by the fixed coil instead of permanent magnet. These instruments
can be used either as ammeter or as voltmeter, but owing to the higher cost
and lower sensitivity of dynamometer ammeters and voltmeters as
compared with moving iron instruments, these are seldom used
commercially as ammeter or voltmeter. However, these are generally used
as wattmeter. Electrodynamic or dynamometer-type wattmeters are very
important because they are commonly employed for measuring power in
AC circuits.3

9.12.1 Dynamometer-type Wattmete3rs

An indicating instrument used to measure power in an electric circuit is

called wattmeter. It measures power in watt or in kW. The pictorial view of
a wattmeter is shown in Figure 9.31.
Fig. 9.31 Wattmeter

Principle

The basic principle of dynamometer-type instruments is that when a

current-carrying moving coil is placed in the magnetic field produced by the
current-carrying fixed coil, a force is exerted on the coil sides of the moving
coil and deflection takes place (Fig. 9.32). In other words, when the field
produced by the current-carrying moving coil (Fr) tries to come in line with
the field produced by the current-carrying fixed coil (Fm), a deflecting
torque is exerted on the moving system and deflection takes place as shown
in Figure 9.33.
Fig. 9.32 Working principle of wattmeter

Fig. 9.33 Working principle of watt-meter

Construction

The dynamometer-type wattmeter essentially consists of two coils called

fixed coil and moving coil. The fixed coil is split into two equal parts that
are placed parallel to each other, as shown in Figure 9.32. The two fixed
coils are air-cored to avoid hysteresis effects when used on AC. The fixed
coil is connected in series with the load and carries the circuit current. It is,
therefore, called current coil.

Fig. 9.34 (a) Constructional features of a wattmeter (b) Circuit diagram of

a wattmeter

The moving coil is pivoted between the two parts of the fixed coil and is
mounted on the spindle. The moving coil is connected in parallel with the
load and carries the current proportional to the voltage applied across the
load. It is, therefore, called potential coil. Generally, a high resistance is
connected in series with the moving coil to limit the current through it. By
limiting the current, the moving coil is made thin and light in weight which
in turn increases the sensitivity of the instrument.
The controlling torque is provided by springs that also serve the additional
purpose of leading current into and out of the moving coil. Air friction
damping (not shown in Fig. 9.34(b)) is employed in such instruments.

Working

When power is required to be measured in a circuit, the instrument is

connected in the circuit as shown in Figure 9.35. The current coil connected
in series with the load carries the load current and the potential coil
connected in parallel with the load carries the current proportional to the
voltage across the load. The fixed coil produces a field Fm (Fig. 9.33) and
moving coil produces a field Fr. This field Frtries to come in line with the
main field Fm, which produces a deflecting torque on the moving coil. Thus,
the pointer attached to the spindle of the moving coil deflects. The
deflection is controlled by the controlling torque produced by the springs.

In the case of AC system, the direction of flow of current is reversed in both

the coils simultaneously in negative half cycle, but the direction of
deflecting torque produced in the moving system remains the same. Hence,
the dynamometer-type wattmeter can be used on DC as well as on AC
supply system.

Fig. 9.35 Circuit diagram of a wattmeter

Deflecting torque

1. In the case of DC system,

Let V = voltage across the load and I = load current
 Current through the fixed coil, I1 ∝ I
Current through the moving coil, I2 ∝ V
Since coils are air-cored, the flux density produced by the fixed coil
is directly proportional to the current I1, i.e., B ∝ I1
Current-carrying moving coil is placed in the flux density produced
by the fixed coil.
∴ Deflecting torque,

Td ∝ BI2 ∝ I1 I2 ∝ IV ∝ Power

Hence, deflecting torque is proportional to power.

2. In the case of AC system,

Let

e = instantaneous voltage across load;

i = instantaneous current through load;
V = rms value of voltage across load;
I = rms value of current through load;
cos ɸ = power factor (lagging) of the load
Now,
e = Vm sin ωt × i = Im sin (ω t – ɸ)

Instantaneous value of current through fixed coil, i1 ∝ i

Instantaneous value of current through moving coil, i2 ∝ e
Due to inertia of the moving system, the deflection will be
proportional to the average torque.
Average deflecting torque, Td ∝ average of (i2 × i1) ∝ average of
(e × i) (9.1)
Now, e × i = Vm sin ωt × Im sin (ω t – ɸ)

Average of (e × i) = Average

of

As the average of over a complete cycle being

sinusoidal quantity is zero.
∴ Average of (e × i) = VI cos ɸ
 Substituting this value in Equation (9.1), we get,
Average deflecting torque, Td ∝ VI cos ɸ ∝ True power
Hence, deflecting torque is proportional to true power in AC
circuits.
The controlling torque is provided by springs,
∴

Tc ∝ θ (where θ is angle of deflection)

In steady position of deflection, Tc = Td or θ ∝ Power

Since deflection θ is proportional to the power to be measured
(consumed by the load) that further depends upon product
of I and V, and therefore, dynamometer-type wattmeters have
uniform scale being crowded in the beginning.
Advantages

1. It can be used on DC as well as AC circuits.

2. It has almost uniform scale.
3. High degree of accuracy can be obtained by careful designing.

Disadvantages

1. At low power factors, the inductances of the potential coil cause serious errors.
2. The reading of the instrument may be affected by stray fields acting on the
moving coil. In order to prevent it, magnetic shielding is provided by enclosing
the instrumental in an iron case.

Errors in Dynamometer-type Wattmeters

The following are the serious errors that may occur in dynamometer-type
wattmeters:

1. Error due to potential coil inductance: The inductance of potential coil is

liable to cause error in the reading of the wattmeter. Because of this error, the
wattmeter gives high reading on lagging power factors and low reading on the
leading power factors. This error can be reduced or compensated by connecting
a capacitor in parallel with a portion of multiplier.
2. Effect due to power loss in potential coil or current coil: Another
possible error in the indicated power may be due to some voltage drop in the
current coil or the current taken by the potential coil. This defect can be
 overcome by having an additional compensating winding that is connected in
series with the potential coil but is so placed that it produces a field in opposite
direction to that of the current coils, as shown in Figure 9.36.

Fig. 9.36 Compensating coil of a wattmeter

3. Error due to eddy currents: The alternating field of current coil induces
eddy currents in the solid metal parts that set up their own magnetic field. This
alters the magnitude and phase of the magnetic field causing deflection. Thus,
the error is introduced in the instrument reading. To reduce this error, the
solid metal parts are removed as far away from the current coil as possible.
4. Error due to stray magnetic field: The dynamometer-type wattmeter has
relatively weak operating field. Therefore, stray fields affect the reading of this
instrument considerably and cause serious errors. Hence, this type of
instruments must be shielded against stray magnetic fields by using iron cases
or providing thin iron shields over the working parts.

Range

1. Current circuit 0–0.25 A to 0–100 A without employing current transformers.

2. Potential circuit 0–5 V to 0–750 V without employing potential transformers.

9.13 INDUCTION-TYPE INSTRUMENTS

Induction-type instruments are used only for AC measurements. These

instruments can be used either as ammeter, voltmeter, or wattmeter.
However, the induction principle finds its widest application as a wattmeter
and energy meter. Induction-type wattmeter is quite suitable to measure
power in an AC circuit where supply voltage and frequency are constant.

9.13.1 Induction-type Wattmeter

Principle

The basic principle of induction-type wattmeter is electromagnetic

induction. When AC flows through two suitably located coils (current coil
and potential coil), they produce rotating magnetic field that is cut by the
metallic disc suspended between the coils; therefore, an emf is induced in
the disc that circulates eddy currents in it. By the interaction of rotating
magnetic field and eddy currents, electromagnetic deflecting torque is
developed that causes the disc to rotate.

Construction

An induction-type wattmeter, as shown in Figure 9.37, has the following

main parts of the operating mechanism:

1. Deflecting mechanism: The deflecting mechanism of the meter consists of

two electromagnets:
1. Series magnet: It consists of a number of U-shaped
laminations of silicon steel staggered together to form a
core. A coil of thick wire having a few turns is wound on
both the legs of U-shaped magnet, as shown in Figure 9.37.
This coil is connected in series with the load. Thus, it is
excited by the circuit current I and is known as current coil.
This magnet is placed below the aluminium disc and
produces the magnetic field ɸse proportional to and in phase
with line current I.
2. Shunt magnet: It consists of a number of M-shaped
laminations of silicon steel assembled together to form a
core. A coil of thin wire having large number of turns in
wound on the central limb of the magnet, as shown
in Figure 9.37. This coil is connected across the load. Thus,
it is excited by the current proportional to the supply
voltage and is known as potential or pressure coil. This
magnet is placed above the aluminium disc.
In order to obtain deflecting torque, current in the pressure
coil must lag behind the supply voltage by 90°. For this,
copper shading band (short circuiting copper ring) is
provided on the central limb of the shunt magnet. The
phase difference of 90° is obtained by adjusting the position
of this shading band. The shading band acts as short-
circuited transformer secondary. Since its resistance is
 negligibly small as compared to its inductance, and
therefore, current circulating in the shading band lags
behind the supply voltage nearly by 90°. Thus, shunt
magnet produces a field ɸsh proportional to applied voltage.
This field is in phase with the current flowing through the
pressure coil Ip, but is in quadrature with the applied
voltage.
2. Deflecting system: It consists of a light aluminium disc mounted on a
vertical spindle. The aluminium disc is positioned in the air gap between the
series and the shunt magnet. The spindle is supported by a cup-shaped
jewelled bearing at the bottom end and has a spring journal bearing at the top
end.

Fig. 9.37 Constructional features of an induction type

energymeter
 3. Controlling torque arrangement: Controlling torque is provided with the
help of two spiral springs placed at the upper and lower side of the spindle
wound in opposite direction, as shown in Figure 9.37.

Tc ∝ θ

4. Damping torque arrangement: A permanent magnet positioned near the

edge of the aluminium disc, as shown in Figure 9.37, is used to provide
necessary damping. When aluminium disc moves in the field of the permanent
magnet, flux is cut and eddy currents are induced in the disc. The direction of
induced currents is such that it opposes the rotation (Lenz’s Law), and thus,
damping torque is produced. Since the induced currents are proportional to the
speed of the disc (N), the damping torque is proportional to the disc speed.
Quick deflection means more damping torque, while slow deflection means
smaller damping torque. The position of braking magnet is adjustable, and
therefore, critical damping can be obtained by adjusting its position.

Working

When wattmeter is connected in the circuit, the current coil carries the load
current and pressure coil carries the current proportional to the supply
voltage. The magnetic field produced by the series magnet (series coil) is in
phase with the line current and the magnetic field produced by the shunt
magnet (pressure coil) is in quadrature with the applied voltage (since the
coil is highly inductive). Thus, a phase difference exists between the fluxes
produced by the two coils. A simplified phasor diagram for an induction-
type wattmeter is shown in Figure 9.38.
Fig. 9.38 Phasor diagram

Let the load current I lags behind the circuit voltage V by an angle ɸ, as
shown in Figure 9.38. Due to shunt magnetic flux, an emf Esh is induced in
the disc; while series magnetic flux produces an emf of Esein the disc. Two
opposite torques are acting in the disc due to ɸsh Ise and fseIsh. The phase angle
between ɸsh and Ise is ɸ and between ɸse and Ish is (180 – ɸ).

∴ Resultant average deflecting torque,

Td ∝ [ɸsh Ise cos ɸ – ɸse Ish cos (180 – ɸ)]

∝ [ɸsh Ise cos ɸ + ɸse Ish cos ɸ]∝ [ɸsh Ise + ɸse Ish] cos ɸsh

where

ɸsh ∝ V; ɸse ∝ I; Ise ∝ I and Ish ∝ V

Td ∝ [VI + IV] cos ɸ ∝ VI cos ɸ

∝ True power of the circuit (P)
As

Td ∝ P and Tc ∝ θ, the wattmeter carries a uniform scale.

Advantages

Induction-type wattmeters have long scale, and they are free from stray
field and have good effective damping.

Disadvantages

1. These are more costly.

2. They can be used only for AC measurements.
3. Change in frequency may cause errors.
4. Sensitive to temperature.

Range

1. Current circuit 0–0.25 A to 0–100 A without employing CTs.

2. Potential circuit 0–5 V to 0–750 V without employing PTs.

9.13.2 Comparison between Dynamometer and Induction-type Wattmeters

The comparison between dynamometer and induction type wattmeters is

given in Table 9.3

Table 9.3 Comparison between Dynamometer and Induction-

Type Wattmeters

S.No. Dynamometer-type Wattmeters Induction-type Wattmeters

1. The instrument can be used on both DC The instrument can be used only on
and AC systems.

2. The instrument can have high degree of The instrument is less accurate. It is
accuracy, if carefully designed. at stated frequency and temperature

3. Power consumption is comparatively low. Power consumption is comparativel

S.No. Dynamometer-type Wattmeters Induction-type Wattmeters

4. Weight of moving system is Weight of moving system is compar

comparatively low.

5. The instrument has uniform scale. The instrument has uniform and lon

6. The instrument has comparatively The instrument has comparatively s

weaker working torque. working torque.

9.13.3 Induction-type Single-phase Energy Meter

Although induction-type instruments can be used as ammeter, voltmeter,

or wattmeter, the induction-type energy meters are more
popular. Induction-type single-phase energy meter is used invariably to
measure the energy consumed in any AC circuit in a prescribed period
where supply voltage and frequency are constant. Energy meter is an
integrating instrument that measures the total quantity of electrical energy
supplied to the circuit in a given period.

Principle

The basic principle of induction-type energy meter is electromagnetic

induction. When AC flows through two suitably located coils (current coil
and potential coil), they produce rotating magnetic field that is cut by the
metallic disc suspended between the coils, and thus, an emf is induced in
the disc that circulates eddy currents in it. By the interaction of rotating
magnetic field and eddy currents, electromagnetic torque is developed that
causes the disc to rotate. This is the same principle that is applied in single-
phase induction motors.

Construction

An induction-type single-phase energy meter, as shown in Figure 9.39, has

the following main parts of the operating mechanism:

1. Driving system: The driving system of the meter consists of two

electromagnets:
1. Series magnet: It consists of a number of U-shaped
laminations of silicon steel staggered together to form a
 core. A coil of thick wire having a few turns is wound on
both the legs of U-shaped magnet, as shown in Figure 9.39.
This coil is connected in series with the load. Thus, it is
excited by the circuit current I and is known as current coil.
This magnet is placed below the aluminium disc and
produces the magnetic field ɸse proportional to and in phase
with line current I.
2. Shunt magnet: It consists of a number of M-shaped
laminations of silicon steel assembled together to form a
core. A coil of thin wire having large number of turns is
wound on the central limb of the magnet, as shown
in Figure 9.39. This coil is connected across the load. Thus,
it is excited by the current proportional to the supply
voltage and is known as potential or pressure coil. This
magnet is placed above the aluminium disc.
In order to obtain deflecting torque, current in the pressure
coil must lag behind the supply voltage by 90°. For this,
copper shading band (short circuiting copper ring) is
provided on the central limb of the shunt magnet. The
phase difference of 90° is obtained by adjusting the position
of this shading band. The shading band acts as short-
circuited transformer secondary. Since its resistance is
negligibly small as compared to its inductance, current
circulating in the shading band lags behind the supply
voltage nearly by 90°. Thus, shunt magnet produces a
field ɸsh proportional to applied voltage. This field is in
phase with the current flowing through the pressure
coil Ip but is in quadrature with the applied voltage.
2. Moving system: It consists of a light aluminium disc mounted on a vertical
spindle. The aluminium disc is positioned in the air gap between the series and
the shunt magnet. The spindle is supported by a cup-shaped jewelled bearing
at the bottom end and has a spring journal bearing at the top end. Since there
is no control spring, the disc makes continuous rotation under the action of
deflecting torque.
3. Braking system: A permanent magnet positioned near the edge of the
aluminium disc, as shown in Figure 9.39, forms the braking system. When
aluminium disc moves in the field of the braking magnet, flux is cut and eddy
currents are induced in the disc. The direction of induced currents is such that
it opposes the rotation (Lenz’s Law), and thus braking torque is produced.
 Since the induced currents are proportional to the speed of the disc (N),
braking torque (TB) is proportional to the disc speed, that is, TB ∝ N
The position of braking magnet is adjustable, and therefore, braking
torque can be adjusted by shifting the magnet to different radial
positions. If the braking magnet is moved towards the centre of the
disc, flux cut by the disc is less. Further, this reduces the induced
current, and thus, the braking torque is reduced. Hence, by the
inward movement of the magnet, braking torque decreases but the
speed of the disc increases and vice versa.

Fig. 9.39 (a) Connection of 1-phase energymeter (b) Connections of

cc and pc in an energymeter

4. Recording mechanism: The function of recording or registering mechanism

is to record continuously a number on the dial that is proportional to the
revolutions made by the moving system. The number of revolutions of the disc
is a measure of the electrical energy passing through the meter.
Working

When the energy meter is connected in the circuit, the current coil carries
the load current and pressure coil carries the current proportional to the
supply voltage. The magnetic field produced by the series magnet (series
coil) is in phase with the line current and the magnetic field produced by
the shunt magnet (pressure coil) is in quadrature with the applied voltage
(since the coil is highly inductive). Thus, a phase difference exists between
the fluxes produced by the two coils. This sets up a rotating field that
interacts with the disc and produces a driving torque, and thus, the disc
starts rotating. The number of revolutions made by the disc depends upon
the energy passing through the meter. The spindle is geared to the
recording mechanism so that electrical energy consumed in the circuit is
directly registered in kWh.

The speed of the disc is adjusted by adjusting the position of the braking
magnet. For example, if the energy meter registers less energy than the
energy actually consumed in the circuit, then the speed of the disc has to be
increased that is obtained by shifting the braking magnet near to the centre
of the disc and vice versa.

Theory

The supply voltage V is applied across the pressure coil. The pressure coil is
highly inductive as it has large number of turns and the reluctance of its
magnetic circuit is very small owing to the presence of short air-gap length.
Thus, the current Ip flowing through the pressure coil is proportional to the
supply voltage and lags behind it by nearly 90°. This current produces a
flux ɸsh that is in phase with Ip and is proportional to applied voltage.

The circuit or load current I flows through the current coil that lags behind
the applied voltage V by an angle ɸ depending upon the power factor (cos ɸ)
of the load. This current produces a flux ɸse that is in phase with I and is
proportional to circuit current, as shown in the phasor diagram (Fig. 9.40).

Esh and Ese are the emfs induced in the disc by the shunt magnetic
flux ɸsh and series magnetic flux ɸse, respectively, and lag behind their
respective fluxes by 90°. The eddy currents Ish and Ise are set up by the
induced emfs and are assumed to be in phase with their respective emfs. All
the quantities are shown vectorially in the phasor diagram shown in Figure
9.40.
Thus, two opposite directed torques are produced due to ɸshIse and ɸseIsh. The
instantaneous value of the net torque is the difference of the two, that is,
(ɸshIse – ɸseIsh). From the phasor diagram, the phase angle
between ɸsh and Ise is ɸ and between ɸse and Ish is (180 – ɸ).

Fig. 9.40 Phasor diagram

Mean driving torque, Td ∝ ɸsh Ise cos ɸ – ɸseIsh cos (180 – ɸ)

or

Td ∝ ɸsh Ise cos ɸ + ɸseIsh cos ɸ

or

Td ∝ (K1VI cos ɸ) + (K2IV cos ɸ)

or
Td ∝ VI cos ɸ (K1 + K2) or Td ∝ VI cos ɸ

or

Td ∝ power (i)

We have seen that braking torque, TB ∝ N, where N is the speed of the

disc. (ii)

For steady speed, the driving torque is equal to the braking torque

Td = TB

From Equations (i) and (ii), we get N ∝ P, where P is power.

Multiplying both sides by time ‘t’, we get

Nt ∝ Pt
Since the product Nt represents the total number of revolutions of the disc
in time t, and the product Ptrepresents the energy passing through the
meter in time t. Thus, number of revolutions of the disc are directly
proportional to electrical energy passing through the meter.

Errors in an induction-type energy meter and their adjustments

The main requirement of an induction-type energy meter is that it should

record the actual energy supplied to the load. However, following are the
errors that may crop up in an energy meter, and to make the correction,
some adjustments are suggested along with the errors:
1. Phase and speed errors: The phase error is introduced because the shunt
magnetic flux does not lag behind the supply voltage by exactly 90° due to
some resistance of the coil and iron losses. The angle of lag is slightly less than
90°. Because of this error, the torque is not zero at zero power factor of the
load, and therefore, energy meter registers some energy even though the actual
energy passing through the meter is zero at zero power factor.
In order to remove this error, the flux produced by the shunt
magnet should be made to lag behind the supply voltage exactly by
90°. This is accomplished by adjusting the position of copper
shading band provided on the central limb of the shunt magnet. An
error on the fast side under these conditions can be eliminated by
bringing the shading band near to the disc and vice versa.
Sometimes, the speed of the disc of an energy meter is either
faster or slower, when tested on a load having moderate power
factor. Therefore, energy meter registers either more or less energy
than the actual energy passing through it and an error is
introduced. In order to remove this error, the radial position of the
braking magnet is adjusted. Movement of the braking magnet, away
from the centre of the disc, increases the braking torque that
decreases the speed of the disc and vice versa.
2. Frictional error: This error is introduced due to friction at the rotor bearing
and in the register mechanism. Because of this error, an unwanted braking
torque acts on the moving system and meter registers less energy than the
actual energy passing through it. This error is compensated by placing two
short circuited bands on the outer limbs of the shunt magnet. These bands
embrace the flux contained in the two outer limbs of the shunt magnet. An emf
is induced and current circulates through them. This causes phase
displacement between the enclosed flux and the main gap flux. As a result of
this, a small driving torque is exerted on the disc solely by the pressure coil that
compensates the frictional torque. The amount of this corrective torque is
adjusted by the variation of the position of the two bands and it should be just
sufficient to overcome the frictional torque, without actually rotating the disc at
no load.
3. Creeping error: The slow but continuous rotation of the energy meter, when
only pressure coil is excited but no current is flowing through the current coil is
called creeping. This error may be due to excessive friction compensation,
excessive voltage supply, stray magnetic field, etc. In order to prevent creeping
on no-load, two holes are drilled in the disc on the opposite side of the spindle
at the same radius. This causes sufficient distortion of the field to prevent
continuous rotation. The disc remains stationary when one of the holes comes
under one of the poles of the shunt magnet.
 4. Temperature error: By the change in temperature, the parameters of the
coils change slightly that introduce a small error in the meter. However, this
error is negligibly small and there is no need to provide any means to eliminate
this error.
5. Frequency error: Since the energy meters are used normally at fixed
frequency, and therefore, they are designed and adjusted to have a minimum
error at declared supply frequency that is normally 50 Hz in India.

9.14 NAME PLATE OF ENERGY METER

The following information is provided by the name plate of a single-phase

energy meter:

1. Voltage
2. Frequency
3. Current
4. Revolutions/kWh
5. Type and its number

Energy meter constant: The number of revolutions made by the disc per
unit (kWh) of energy passing through the energy meter is called energy
meter constant.

9.15 CONNECTIONS OF SINGLE-PHASE ENERGY METER TO SUPPLY POWER TO A

DOMESTIC CONSUMER

The electricity or electrical energy consumed by a consumer is measured

with the help of an energy meter. A supplier gives energy to a consumer
through an energy meter and the load of the consumer is connected to the
meter, as shown in Figure 9.41.
Fig. 9.41 Connections of energymeter to measure electrical energy of a
domestic consumer

The reading of the energy meter is recorded every month (or after two
months as the case may be), the difference between the present reading and
the previous reading shows the energy consumption during the said period.

Example 9.23

A 230 V single-phase energy meter has a constant load current of 20 A at

unity power factor. If the meter disc makes 2,300 revolutions during 2 h,
calculate the meter constant. If the power factor were 0.8 lagging, what
would be the number of revolutions made by the disc in 3 h?

Solution:

Supply voltage, V = 230 V; load current, I = 20 A

Power factor, cos ɸ = 1; time, t = 2 h

Energy supplied = VI cos ɸ × t = 230 × 20 × 1 × 2 = 9,200 Wh = 9.2 kWh

Number of revolutions made by the disc during this period, N = 2,300

If the power factor, cos ɸ = 0.8

Energy supplied = 230 × 20 × 0.8 × 3 = 11,040 Wh = 11.04 kWh

Number of revolutions made by the disc, N = meter constant × energy

supplied
= 250 × 11.04 = 2,760.
Example 9.24
For a 5 A, 230 V energy meter, the number of revolutions per kWh is 480. If
upon test at full load u.p.f., the disc makes 5 revolutions in 32 s, calculate
the percentage error.

Solution:

Supply voltage, V = 230 V; full load current, I = 5A

Energy constant, K = 480 revolutions/kWh

Energy consumed at full load unity p.f. in

32

Number of revolutions required to be made by the disc

N = K × energy supplied = 480 × 0.01022 = 4.9067 revolutions

Actual number of revolutions made by the disc, N′ = 5

Energy meter actually registers more energy than the actual energy passing
through it. Therefore, it causes loss to the consumer and gain to the
supplier.

Example 9.25

The name plate of a single-phase energy meter installed in a house reads

1,200 revolutions/kWh. If 5 lamps of 100 W each and 5 lamps of 60 W each
are operated for 1 h, the disc makes 1,000 revolution. State whether the
meter reads correctly or not.

(Jan. 1995)
Solution:

Energy meter constant, K = 1,200 revolutions/kWh

Energy consumed in 1

Number of revolutions required to be made by the disc

N = K × energy consumed = 1,200 × 0.8 = 960

Actual number of revolutions made by the disc, N′ = 1,000

Hence, the meter reads incorrectly. In this case, the meter is faster and it
records more than the actual energy passing through it.

Example 9.26

A 50 A, 230 V meter on full load test makes 61 revolutions in 37 s. If the

normal disc speed is 500 revolutions/kWh, find the percentage error.

(U.P.T.U. 2005-06)

Solution:

Energy meter constant, K = 500 revolutions/kWh

V = 230 V, I = 50 A; t = 37 s

Actual energy consumed by load

Number of revolutions that should be made by energy meter disc during the
consumption of actual energy = 0.118194 × 500 = 59.1

Actual revolution’s made by the disc = 61. The instrument is reading higher
than the actual.

This error should be subtracted from the measured values.

Example 9.27

An energy meter revolves 10 revolutions of disc for one unit of energy. Find
the number of revolutions made by it during an hour when connected
across load, which takes 20 A at 210V and 0.8 power factor leading. If
energy meter revolves 35 revolutions, find the percentage error.

(U.P.T.U. 2004-05)

Solution:

Meter constant, K = 10 revolutions/kWh

Energy consumed in 1 h

Number of revolutions required to be made by the disc

= K × energy consumed = 10 × 3.36 = 33.6

Number of revolutions made by the disc of energy meter = 35

Energy recorded by the energy meter

Example 9.28

A 230 V single-phase energy meter has a constant load current of 10 A at

unity power factor. If the meter disc makes 1,150 revolution during 2 h,
calculate the meter constant. If the power factor were 0.8, what would be
the number of revolutions made by the disc in the same time?

Solution:

Supply voltage, V = 230 V; load current, I = 10 A; power factor, cos ɸ = 1;

and time, t = 2 h.

Energy supplied = VI cos ɸ × t = 230 × 10 × 1 × 2 = 4,600 Wh = 4.6 kWh

Number of revolutions made by the disc during this period; N = 1,150

If the power factor, cos ɸ = 0.8

Energy supplied = 230 × 10 × 0.8 × 2 = 3,680 Wh = 3.68 kWh

∴
Number of revolutions made by the disc,

N′ = meter constant × energy supplied = 250 × 3.68 = 920.

Example 9.29

A single-phase energy meter has a registration constant of 100

revolutions/kWh. If the meter is connected to a load carrying 20 A at 230 V
and 0.8 power factor for an hour, find the number of revolutions made by
it. If it actually makes 360 revolutions, find the percentage error.

(U.P.T.U. Feb. 2002)

Solution:

Energy consumed in 1

Number of revolutions required to be made if it is correct

= 3.68 × registration constant in revolution/kWh

= 3.68 × 100 = 368.

Number of revolutions actually made = 360

Percentage error

The negative sign shows that the disc of the meter is rotating slow.

9.16 DIFFERENCE BETWEEN WATTMETER AND ENERGY METER

The difference between wattmeter and energy meter are given in Table 9.4.
Table 9.4 Difference between Wattmeter and Energy Meter

S.No. Wattmeter Energy meter

1. It is an indicating instrument. It is an integrating instrument.

2. It measures electric power. It measures electrical energy.

3. It contains graduated scale to measure It contains recording mechanism

electrical quantity at an instant. electrical energy in a given period

4. It has a device that provides controlling It has no controlling torque.

torque.

5. It indicates the power consumed by the It adds- up the energy consumed b

circuit at a particular instant. in a given period.

9.17 DIGITAL MULTIMETER

A digital multimeter (DMM) displays the AC or DC voltages being

measured directly as discrete numerals in the decimal number system.
Numerical readout of DMM is very convenient and it eliminates
observational error. The use of digital multimeters increases the speed with
which the readings can be taken.

The DMM is a versatile and accurate instrument used in laboratories. On

account of developments in the integrated circuits (IC) technology, it has
become possible to reduce the size, power requirements, and cost of digital
multimeters.

The basic function performed by a digital multimeter is an analogue to

digital (A/D) conversion. For example, the voltage value may be changed to
a proportional time interval, which starts and stops a clock oscillator. In
turn, the oscillator output is applied to an electronic counter that is
provided with a readout in terms of voltage. There are many ways of
converting the analogue reading into digital form, but the most common
way is to use ramp voltage. The operating principle of a ramp-type DMM is
simple. A ramp voltage increases linearly from zero to a predetermined
level in a predetermined time interval. The ramp voltage value is
continuously compared with the voltage being measured. At the instant, the
value of ramp voltage becomes equal to that of unknown voltage, a
coincidence circuit called input comparator, generates a pulse that opens
the gate as shown in Figure 9.42. The ramp voltage continues to decrease
till it reaches the ground level. At this instance, another comparator
generates a pulse and closes the gate. The time interval between the
opening and the closing of gate is measured with an electronic time-interval
counter. This count is displayed as a number of digits.

Fig. 9.42 Block diagram of a digital multimeter

Fig. 9.43 Outer view of a digital multimeter

Figure 9.43 shows the pictorial view of a DMM. The main parts on the
panel are as follows:

1. Digital display unit: It displays the reading in digits.

2. ON–OFF switch: It is used to switch ON and OFF the power of battery.
3. Input terminals: There are four sockets; one of them is common to which
black lead is inserted. The other three sockets to which red lead is connected
are: (a) V – for measurement of DC and AC voltage and resistance; (b) A – for
measurement of DC and AC current up to 2 A; and (c) 10A – for measurement
of DC and AC current up to 10 A.
4. Mode switch: For measurement of either DC or AC voltage or current, this
switch is used to select the mode.
5. Range switch: The central switch is used to select the range of quantity
(voltage, current, or resistance) to be measured.
PRACTICE EXERCISES
Short Answer Questions

1. What are dynamometer-type instruments? Why these are used only as

wattmeter?
2. What are dynamometer-type wattmeters? How deflecting, controlling, and
damping torque is provided in such instruments?
3. Mention the main causes of error in dynamometer-type moving coil
wattmeters.
4. What is the basic working principle of induction-type wattmeter? What is its
field of application? Which type of controlling and damping torque is provided
in such instruments?
5. What for single-phase energy meter is used? What is its basic working principle
and field of application? Give some important mathematical relations.
6. What are the prominent errors that may occur in induction-type energy
meters? How these errors can be adjusted or compensated?
7. What do you mean by energy meter constant?

Test Questions

1. In an industry, a voltmeter and ammeter are connected along with a wattmeter.

Will the reading of wattmeter be equal to the reading of voltmeter × reading of
ammeter, support your arguments.
2. Describe the construction and expression for torque for an
electrodynamometer-type wattmeter.

Or

Describe the principle of operation and construction of a

dynamometer-type wattmeter. Why is the scale of such an
instrument uniform?
3. Name and explain the instrument you will use for measuring VI cos θ. Give the
circuit diagram for measuring VI cosθ in three-phase circuit.
4. How can you measure power and power factor in a single-phase circuit? Draw
the circuit diagram and explain.

Or

How can you find the power and power factor of a cooler? Explain
with the help of a circuit diagram.
 5. Discuss merits and demerits of dynamometer-type wattmeter.
6. What are sources of error in a wattmeter? How can they be minimised?
7. What are the merits and demerits of induction-type wattmeter?
8. How you can measure the electricity consumption in houses? Explain the
process and working of the instrument.

Or

What type of meter is installed in housing electricity board? What

and how it measures? What it cannot measure? Explain.
9. What is induction-type watt-hour meter? Explain its construction and working.
10. How wattmeter and energy meter differ?
11. What are the errors in induction-type energy meter and how these can be
adjusted?

Or

Explain sources of error and various adjustments involved in

single-phase induction-type energy meter.

Or

Write a note on friction compensation and creeping error in

induction-type watt-hour meter.
12. Calculate the energy consumed by a heater of 2 kW rating if it works for 10 h.
13. The disc of an energy meter makes 600 revolutions per unit of energy. When a
1,000 W load is connected, the disc rotates at 10.2 rpm. If the load is on for 12
h, how many units are recorded as error?

Numericals

1. A 40 A, 230 V energy meter on full load test makes 60 revolutions in 46 s. If

the normal disc speed is 500 revolutions/kWh, find the percentage error with
proper sign by assuming the load to be purely resistive.
(Ans. +2.08% (fast)) (U.P.T.U. June 2004)

2. A single-phase energy meter has a constant of 1,200 revolutions/kWh. When a

load of 200 W is connected, the disc rotates at 4.2 revolutions/min. If the load
is on for 10 h, how many units are recorded as an error? Further, find
percentage error.
 (Ans. 0.1 kWh (more), 5%)

3. An energy meter is designed to make 100 revolutions of the disc for one unit of
energy. Calculate the number of revolutions made by it when connected to a
load carrying 25 A at 230 V and 0.8 p.f. for an hour. If it actually makes 450
revolutions, find the percentage error and explain it from the consumer point
of view.
(Ans. −2.174% (less))

4. A single-phase energy meter has a constant speed of 1,300 revolutions/kWh.

The disc revolves at 3.5 rpm when a load of 150 W is connected to it. If the load
is on for 11 h, how many units are recorded as error? What is the percentage
error?
(Ans. 0.127 kWh, 7.69%) (U.P.T.U Sep. 2001)

5. A 50 A, 230 V meter on full load test makes 61 revolutions in 37 s. If the normal

disc speed is 500 revolutions/kWh, find the percentage error.
(Ans. 3.223%)

6. For a 5A, 230 V meter, the number of revolutions/kWh is 480. If at unity

power factor, the disc, upon test, makes 10 revolutions in 64 s, calculate the
percentage error.
(Feb. 1994) (Ans. Required revolutions = 9.813; % error = −1.9)

7. A 230 V, single-phase energy meter has a constant load current of 4 A passing

through the meter for 5 H at unity p.f. If the meter disc makes 1,104 revolutions
during this period, what is the constant in revolutions/kWh. If the p.f. is 0.8,
what number of revolutions will the disc make in the same time?
(Ans. 240 revolutions/kWh, 883.2)

8. The name plate of single-phase energy meter installed in a house reads as

4,800 revolutions/kWh. If three lamps of 100 W each are operated for 4 min,
the disc makes 100 revolutions. State whether the meter reads correctly or not.
(Ans. N = 96 revolutions, Incorrect)

9. An energy meter is designed to make 100 revolutions of the disc for one unit of
energy. Calculate the number of revolutions made by it when connected to a
 load carrying 20 A at 230 V and 0.8 p.f. for an hour. If it actually makes 360
revolutions, find the percentage error and explain it from the consumer point
of view.

(Ans. 2.175%)

SUMMARY

1. Measurement: The fixed quantity which is taken as basis is called unit and the
process of comparing the quantity with this unit is termed as measurement.
2. Electrical instruments: The instruments, such as ammeter, voltmeter, energy
meter, and megger are used to measure electrical quantities are called electrical
instruments.
3. Classification of electrical instruments: 1. Absolute instruments 2. Secondary
instruments.
4. Absolute instruments: The instruments that give the value of the quantity to be
measured in terms of constants of the instrument are called absolute
instruments.
5. Secondary instruments: The instruments that determine the electrical quantity
to be measured directly in terms of deflection are called secondary
instruments.
6. Indicating instruments: The instruments that indicate the magnitude of
electrical quantity being measured instantaneously are called indicating
instruments.
7. Integrating instruments: The instruments that add up the electrical quantity,
such as electrical energy and measure the total energy (in kWh) in a given
period are called integrating instruments.
8. Recording instruments: The instruments that give a continuous record of the
variations of the electrical quantity being measured are called recording
instruments.
9. Essentials of indicating instruments: The forces or torques required for
satisfactory operation of indicating instruments are called essentials of
indicating instruments, such as: 1. Deflecting torque 2. Controlling torque 3.
Damping torque.
10. Deflecting torque: The deflecting or operating torque (Td) is produced by
making use of any one of the effects such as magnetic, electrodynamic,
electromagnetic induction etc.
11. Controlling torque: The controlling or restoring torque (Tc) opposes the
deflecting torque and increases with the deflection of the moving system. The
pointer is brought to rest at a position where the two opposing torques (i.e.
deflecting torque and controlling torque) are equal.
12. Damping torque: When deflecting torque is applied to the moving system, it
deflects the pointer. While the controlling torque controls the deflection and
tries to stop the pointer at its final position. But due to inertia the pointer
oscillates around its final position. To bring the pointer at its final position
quickly damping torque is provided. It always acts in opposite direction to
motion.
13. Methods of providing controlling torque: Controlling torque is provided by
(i) Spring control method (Tc ∝ θ ) (ii) Gravity control method (Tc ∝
sin θ ).
14. Methods of providing damping torque: (i) Air friction (ii) Fluid friction (iii)
Eddy currents
15. Errors common to all types of instruments: These error are (i) Temperature
error (ii) Friction error (iii) Observational error.
16. Types of moving iron instruments: (i) Attraction type (ii) Repulsion type.
17. Error in moving iron instruments: These are (i) Error due to hysteresis (ii)
Error due to stray magnetic field (iii) Error due to temperature (iv) Error due
to change in frequency.
18. Application of moving iron instruments: These can be used on AC as well as on
DC.
19. Permanent magnet moving iron instruments (PMMI): It carries a permanent
magnet, a coil wound on a light aluminium former and a pointer.
20. Application of PMMI: Used on DC only.

TEST YOUR PREPARATION

FILL IN THE BLANKS

1. Observational errors are called ________.

2. The deflection in moving iron instrument is proportional to _________.
3. Indicating instruments are _________ slightly less than critically damped.
4. In indicating instruments, controlling torque always opposes the
_______torque.
5. A meter, which measures the discrete value of a quantity, is called _________
instrument.
6. One unit of electrical energy means __________.
7. Wattmeter is an instrument that measures ____________power.
8. The instruments, which indicate electrical quantities at particular instant, are
called ___________ instruments.
9. Example of integrating instrument is __________.
10. Example of indicating instrument is _________ and example of integrating-
type instrument is __________.
11. A wattmeter measures __________ power.
12. In energy meters, controlling torque is provided by __________.
13. The example of an absolute instrument is __________.
14. A tangent galvanometer is __________ instrument.
15. Damping torque __________ the deflecting torque.
16. Damping torque in energy meter is provided by __________.
17. __________ is the part, commonly available in all meters.
18. Cost of gravity control system is __________ than spring control system.
19. Moving iron instruments have __________ scale.
20. The type of instrument is used for both AC and DC is__________.
21. The range of an ammeter can be extended by using __________.
22. PMMC instruments can be used for ________ measurements only.
23. Moving coil instruments have __________ scale.
24. Voltmeters should have__________ resistance.
25. _______ type of instruments can be used for AC as well as DC current and
voltage measurement.
26. The MI instrument has __________ scale.
27. The multiplier is made of __________ material.
28. Ammeters should have __________ internal electrical resistance.
29. The internal resistance of an ammeter is __________.
30. The scale of PMMC instruments is __________.
31. Moving coil (PMMC) instruments can be used for __________.
32. The deflection in moving iron instrument is proportional to __________.
33. An ammeter is always connected in __________ with load.
34. The power consumption in moving coil instruments is typically about____
35. The scale of moving iron-type instruments is _____________.
36. A high torque to weight ratio in an analogue indicating instrument indicates
_____________ friction loss.
37. Swamping resistance is connected in series with the meter in order to
reduce______ errors in shunted ammeters.
38. Moving coil instruments can be used on _________. _________.
39. Voltmeter having high input resistance will be more accurate (yes or no).
40. In moving iron instruments, the deflecting torque is directly proportional to
the ______.
41. In moving iron-type instruments __________ damping cannot be provided.
42. Draw the symbolic representation of a wattmeter.
43. Wattmeter reading P = _______.
44. Wattmeter measures _________ (VI/VI cos θ or VI sin θ)
45. Electrodynamometer-type instruments have uniform or non-uniform scale.
46. A wattmeter measures_________ power.
47. Electrodynamic-type instruments have _________ scale.
48. Energy meters have __________ torque or weight ratio.
49. Creeping is the phenomenon, which occurs in __________.
50. Energy meter is __________ type of instrument.
51. Energy meter measures _________ (VI/VI cos θ or VI sin θ or none)
52. Energy meter in hours measure __________.
53. Energy is given by a product of _________. _________.
54. In relation P = VI cos f. V and I are the values of _________. _______

OBJECTIVE TYPE QUESTIONS

1. The instruments that give the value of the quantity to be measured in terms of
constants of the instrument are called
1. indicating instruments.
2. absolute instruments.
3. secondary instruments.
4. integrating instruments.
2. The instruments that determine the electrical quantity to be measured directly
in terms of deflection are called
0. absolute instruments.
1. integrating instruments.
2. secondary instruments.
3. recording instruments.
3. The instruments that indicate the magnitude of electrical quantity being
measured instantaneously are called
0. integrating instruments.
1. recording instruments.
2. indicating instruments.
3. All of these
4. The deflecting torque in an indicating instrument
0. brings the needle to zero position when instrument is
disconnected.
1. deflects the needle.
2. brings the pointer quickly to its final deflected position.
3. none of these.
5. The controlling torque in an indicating instrument
0. brings the pointer back to zero position when instrument is
disconnected.
 1. controls the deflection and tries to stop the pointer at its
final position where deflecting torque is equal to controlling
torque.
2. reduces the oscillations of the pointer and brings the
pointer quickly to its final position.
3. Both (a) and (b).
6. Damping torque is provided in indicating instruments by
0. air friction.
1. fluid friction.
2. eddy current.
3. All of these
7. Controlling torque is provided in an indicating instrument by
0. air friction.
1. spring or gravity control.
2. fluid friction.
3. eddy currents.
8. Deflecting torque is provided in an indicating instrument by
0. air friction.
1. fluid friction.
2. gravity control.
3. None of these
9. Overdamping will
0. make the pointer to rise quickly to its deflected position without
overshooting.
1. make the pointer slow and lethargic.
2. make the pointer to oscillate about its final position and
take some time to come to rest in its steady position.
3. None of these
10. For better performance, the indicating instruments should be
0. critically damped.
1. overdamped.
2. underdamped.
3. lethargic.
11. Energy meter is
0. an indicating instrument.
1. an integrating instrument.
2. a recording instrument.
3. an absolute instrument.
12. In the instrument provided with spring control
0. Td ∝ I.
 1. Tc ∝ I.
2. Tc ∝ θ.
3. Td ∝ θ.
13. In the instruments provided with gravity control
0. Tc ∝ θ.
1. Td ∝ sinθ.
2. Td ∝ θ.
3. Tc ∝ sinθ
14. Damping torque is provided in
0. indicating instruments.
1. integrating instruments
2. recording instrument.
3. absolute instruments.
15. Eddy current damping cannot be provided in the indicating instruments
0. permanent magnet moving coil instruments.
1. moving iron instruments.
2. indication-type instruments.
3. None of these.
16. The internal resistance of a voltmeter is
0. zero.
1. very small.
2. very high.
3. infinite.
17. The internal resistance of a voltmeter must be very high in order to
0. have maximum loading effect.
1. have more current supplied by the voltage source.
2. unalter the circuit conditions.
3. reduce the current through the meter.
18. The shunt used in the milliammeter
0. will extend the range and increases the resistance.
1. will extend the range and decreases the meter resistance.
2. will decrease the range and meter resistance.
3. will decrease the range and increases the meter resistance.
19. A moving coil (permanent magnet) instrument can be used to measure
0. low frequency AC.
1. high frequency AC.
2. both DC and AC both.
3. DC only.
20. In permanent magnet moving coil instruments, damping torque is provided by
0. air friction.
 1. eddy currents.
2. fluid friction.
3. Either (a), (b), and (c)
21. In permanent magnet moving coil instruments, the scale is
0. uniform.
1. non-uniform.
2. crowded at the end.
3. uniform at the beginning.
22. To extend the range of an ammeter
0. a high resistance is connected in series with it.
1. a low resistance is connected in series with it.
2. a low resistance is connected in parallel with it.
3. a high resistance is connected in parallel with it.
23. To extend the range of a voltmeter,
0. a high resistance is connected in series with it.
1. a low resistance is connected in series with it.
2. a low resistance is connected in parallel with it.
3. a high resistance is connected in parallel with it.
24. The value of the resistance required to extend the range of voltmeter is given by
the relation

0.

1.
2. R = (m – 1) Rm
3. R = (m + 1) Rm
25. The value of the resistance required to extend the range of an ammeter is given
by the relation

0.

1.
2. Rs = (N + 1) Rm
3. Rs = (N – 1) Rm
where N = multiplying power of the shunt.
26. The dynamometer-type wattmeter can be used to measure
0. DC power only.
1. AC power only.
2. neither AC nor DC power.
3. both DC and AC power.
27. The wattmeter
0. has three connections two of which are used at a time.
1. can measure DC power but not 60 c/s AC power.
2. has voltage and current coils to measure the real power.
3. only measures apparent power.
28. The one ‘unit’ of energy measured in AC circuit is equivalent to
0. 1 W
1. 1 kWh
2. 1 Wh
3. 1 kW
29. The steady speed of the disc in an energy meter is achieved when
0. braking torque is zero.
1. braking torque is more than operating torque.
2. braking torque is half of the operating torque.
3. operating torque is equal to braking torque.
30. Creeping is the phenomenon that occurs in
0. ammeter.
1. voltmeter.
2. energy meter.
3. wattmeter.
31. The induction-type single-phase energy meter is
0. an ampere-hour meter.
1. true watt-hour meter.
2. wattmeter.
3. volt-ampere-reactive meter.
32. Two holes are drilled in the disc of energy meter on the opposite side of the
spindle
0. to eliminate creeping on no load.
1. for proper ventilation.
2. to reduce weight of the disc for easy rotation.
3. to increase the deflecting torque.
33. In an induction-type energy meter, the frictional error is compensated by
0. adjusting the opposition of brake magnet.
1. placing short circuiting band on the two side limbs of the
shunt magnet.
2. drilling two holes in the aluminium disc.
3. adjusting the position of short circuiting band on the central
limb of the shunt magnet.

NUMERICALS
1. A 15 V moving iron voltmeter has a resistance of 500 Ω and inductance of 0.12
H. Assuming that this instrument reads correctly on DC, what will be its
reading on AC at 15 V when the frequency is 25 Hz and 100 Hz.
(Ans. 14.99 V, 14.83 V)

2. In a moving coil instrument, the moving coil consists of 100 turns wound on a
square former of length 3 cm. The flux density in the air gap is 600 lines/cm2.
Calculate the turning moment acting on the coil when carrying a current of 12
mA.
(Ans. 6.48 × 10–5 Nm)

3. A moving coil instrument gives full-scale deflection with 15 mA and has a

resistance of 5 Ω. Calculate the resistance to be connected (i) in parallel to
enable the instrument to read up to 1 A and (ii) in series to enable it to read up
to 100 V.
(Ans. 0.0761 Ω, 6,661.7 Ω)

4. A moving coil instrument gives full-scale reading at 25 mA when a potential

difference across its terminals is 75 mV. Show how it can be used to measure a

current of 100 A and voltage up to 750 V.

(Ans. 0.00075 Ω, 29,997 Ω)

5. A dynamometer-type instrument that gives a maximum reading of 20 mA has a

resistance of 5 Ω. Show how it may be used to measure 400 V and 20 A.
(Ans. 19,995 Ω, 0.005005 Ω)

6. A 230 V, single-phase energy meter has a constant load current of 4 A passing

through the meter for 5 H at unity p.f. If the meter disc makes 1,104 revolutions
during this period, what is the constant in revolutions/kWh? If the p.f. is 0.8,
what number of revolutions will the disc make in the same time?
(Ans. 240 revolutions/kWh, 883.2)

7. The name plate of single-phase energy meter installed in a house reads as

4,800 revolutions/kWh. If three lamps of 100 W each are operated for 4 min,
the disc makes 100 revolutions. State whether the meter reads correctly or not.
 (Ans. N = 96 revolutions, incorrect)

VIVA VOCE OR REASONING QUESTIONS

1. Damping torque is different to controlling torque. How?

2. There is no need of controlling torque in the case of integrating instruments.
Why?
3. Damping torque is essential for indicating instruments. Why?
4. In gravity control method, controlling torque is proportional to sine of
deflection angle θ. Why?
5. Damping torque can be provided by eddy currents. How?
6. Eddy current damping is not possible is moving iron instruments. Why?
7. Moving iron instruments can be used both on DC and AC. Why?
8. For general purpose, moving iron voltmeters and ammeters are used. Why?
9. The scale of moving iron instruments is not uniform. Why?
10. The permanent magnet moving coil instruments cannot be used on AC. Why?
11. The voltmeters have very high resistance. Why?

Or

Voltmeters are always connected in parallel to the load and have

very high resistance. Why?
12. The ammeters have very low resistance. Why?

Or

Ammeters are always connected in series with the load and have
very small resistance. Why?
13. To extend the range of an ammeter, shunts (very small resistances) are
connected in parallel to the instrument, why?
14. In dynamometer-type wattmeter, current coil is the fixed coil and potential coil
is moving coil, why not vice versa?
15. The scale of dynamometer-type wattmeter is non uniform. Why?
16. The disc of induction-type energy meter is made of aluminium and not of wood
or iron. Why?
17. No controlling torque is provided in an induction-type energy meter. Why?
18. A copper short circuiting band is provided on the central limb of the shunt
magnet of an induction-type single-phase energy meter. Why?
19. Two short circuiting bands of copper are provided on the side limbs of the
shunt magnet of an induction-type single-phase energy meter. Why?
20. Two holes are provided in the disc of an electromagnetic induction-type energy
meter. Why?
21. If an energy meter indicates more energy than the actual energy consumed,
then the braking magnet is brought near to the axis or away from the axis to
remove the error. Why?

SHORT ANSWER TYPE QUESTIONS

1. What are absolute Instruments?

2. What do you understand by a secondary instrument?
3. How are secondary instruments classified?
4. What is an indicating Instrument?
5. What are recording instruments?
6. What are integrating instruments?
7. What is a deflecting torque?
8. What is the function of controlling torque in indicating instruments?

Or

Why is controlling mechanism provided in indicating instruments?

9. List out the advantages and disadvantages of gravity control when compared to
spring control:
(ii) Cramped scale.
(iii) The instrument should be properly levelled to avoid zero error.
10. What is the necessity of damping torque in indicating instruments?

Or

Why do we require damping torque in an indicating instrument?

11. Why is fluid friction damping not much used nowadays?
12. What are the types of moving iron instrument?
13. Explain the principle of operation of attraction-type moving iron instruments.
14. What is the basic principle of repulsion-type moving iron instruments?
15. What are the advantages of moving iron instruments?
16. List the disadvantages and moving iron instruments.
17. Why is the graduation of moving iron instrument not uniform throughout?
18. Why are iron made of Mumetal employed in moving iron instruments?
19. Why are repulsion-type moving iron instruments more commonly used than
attraction-type one?
20. Why eddy current damping is not used in moving iron?
21. What do you mean by a linear scale and squared scale?
22. What is the difference between an ammeter and a voltmeter?
23. How will you make an ammeter from moving iron instrument?
24. Why should an ammeter have low resistance?
25. How to develop a voltmeter from a moving iron instruments.
26. Why should voltmeter have high resistance?
27. Why do we use a multiplier with a voltmeter?
28. Ammeters and voltmeters are connected in series and parallel, respectively.
Why?
29. What are the two types of moving coil instruments?
30. What is principle of permanent magnet-type moving coil instruments?
31. What are the advantage of PMMC instruments?
32. What are the disadvantages of PMMC instruments?
33. Why permanent magnet moving coil instruments cannot be used for AC
measurements?
34. Compare moving coil instruments with moving iron instruments.
35. What is dynamometer-type wattmeter?
36. Why are dynamometer instruments insensitive?
37. Why is eddy current damping not used in dynamometer-type instruments?
38. Why is dynamometer-type instrument mainly used as a wattmeter?
39. Why dynamometer instruments are not usually used for DC measurement?
40. What are the advantages of dynamometer-type wattmeter?
41. What are the disadvantages of dynamometer-type wattmeter?
42. Why are dynamometer wattmeter always preferred to induction wattmeters for
AC power measurement?
43. What is an energy meter?
44. What is induction-type energy meter?
45. What is the principle of induction-type energy meter?
46. Why the rotating system of the energy meter is made as small as possible?
47. Why is it necessary that the strength of brake magnet should remain constant
during the use of the meter?
48. List the different parts of single-phase induction-type energy meter.
49. Why are of aluminium disc is preferred over copper disc?
50. Why does the rotating disc of an induction-type energy meter carry a small
hole?
51. What is meant by compensating loop with reference to induction-type energy
meter?

TEST QUESTIONS

1. What is the difference between absolute and secondary instruments?

Or

Differentiate between primary and secondary instruments.

2. Classify instruments and clearly differentiate between absolute and secondary
instruments.
(P.T.U.)

3. Differentiate between indicating, recording, and integrating instruments.

4. Differentiate between recording and integrating type of instruments. Give two
examples of each of these.
(P.T.U.)

5. Explain the essentials of indicating instruments.

(P.T.U.)

6. Name different types of torques provided in indicating instruments. Explain

why these torques are required.
7. Describe the following in the case of measuring instruments:
(i) deflecting torque; (ii) controlling torque; and (iii) damping
torque.
(U.P.T.U. Sept. 2003)

8. Discuss common features of indicating instruments.

(U.P.T.U. Feb. 2002)

9. Explain the methods of providing controlling torque in indicating instruments.

(P.T.U.)

10. Describe how controlling torque is obtained by using a spring.

11. Describe how controlling torque is obtained by using gravity control method.
Further, show that in this method, Tc μ sin θ, where θ is the deflection angle.
12. What is the purpose of damping torque is an indicating instrument? How is it
usually provided?
(P.T.U.)
13. Describe the operating principle of measuring instruments. What are the
various torques acting on the moving mechanism of the instruments? How are
these obtained and what are their roles in the operation of the instruments?
(U.P.T.U. Sept. 2001)

14. Explain the methods of providing controlling torque in indicating instruments.

(P.T.U.)

15. Explain different methods of obtaining damping torque in indicating

instruments.
16. Explain why eddy current damping is not possible in moving iron instruments.
17. Compare the spring control and gravity control method of providing
controlling torque in indicating instruments.
18. Describe with neat sketch the principle, construction, and working of moving
iron attraction-type instruments.
19. Describe with neat sketch the principle, construction, and working of moving
iron repulsion-type instrument.

Or

Explain with neat sketch the principle, construction and, working of

a repulsion-type moving iron instrument. Show that deflection θ is
directly proportional to square of the current flowing through the
coil. State the advantages and disadvantages of moving iron
instruments.
20. Explain the principle and construction of attraction-type moving iron
instruments. Discuss their merits and demerits.
(U.P.T.U. Jan. 2003)

21. Explain the principle of operation of one type of moving iron instrument,
showing how it is suitable for use on both AC and DC systems.
(U.P.T.U. July 2002)

22. Explain the principle of operation of a repulsion-type moving iron instrument.

Discuss its merits and demerits.
(U.P.T.U. Feb. 2001)
23. How is deflecting torque produced in a repulsion-type moving iron
instruments? Why is the graduation of the scale not uniform in these
instruments?
(M.Univ. Aug. 1990)

24. Drive the general equation for deflection for a spring-controlled repulsion-type
moving iron instrument.
(P.T.U.)

25. Give advantages and disadvantages of moving iron-type instruments.

(P.T.U.)

26. Discuss different types of errors present with moving iron type of instrument.
(B. Univ. Oct. 87)

27. Compare merits and demerits of moving coil and moving iron instruments.
(U.P.T.U. Feb. 02)

28. Mention the errors in moving iron instruments.

(P.T.U.)

29. Describe with neat sketch a permanent magnet moving coil ammeter and
discuss its errors.
(P.T.U.)

30. Discuss the construction and working of permanent magnet moving coil-type
instrument with the help of a neat sketch. Further, write its advantages of
disadvantages.
(P.T.U.)

31. Explain the difference between moving coil and moving iron instruments with
examples.
(M. Univ. April. 1988)(U.P.T.U. Tut.)

32. Discuss different sources of errors in PMMC instruments

(P.T.U.)
33. Explain the construction of a permanent magnet moving coil instruments with
a neat sketch.
(P.T.U.)

34. Explain why PMMC instruments are used most widely. Enlist their advantages
and disadvantages.
(U.P.T.U. Tut.)

35. With the help of neat labelled diagrams, explain briefly the construction and
principle of operation of permanent magnet moving coil type of indicating
instruments.
(U.P.T.U. June 2001)

36. Derive the expression for torque produced in a moving coil type of instrument
and explain briefly its working.
(U.P.T.U. June 2004)

37. Describe a PMMC instrument in detail. Further, discuss its advantages and
disadvantages.
(U.P.T.U. Sept. 2001)

38. Enlist the advantages and disadvantages of permanent magnet moving coil
(PMMC) instruments.
(U.P.T.U. Sept. 2001)

39. Describe with the aid of a labelled diagram, the constructional details of a
moving coil instrument, and also explain how ‘control’ and ‘damping’ forces are
obtained.
(U.P.T.U. July 2002)

40. What is difference between an ammeter and voltmeter?

(P.T.U.)

41. Explain how will you extend the range of an ammeter.

(P.T.U.)
42. Explain how will you extend the range of a voltmeter.
(P.T.U.)

43. Derive expressions for multiplying powers when the range of a moving coil
instrument is increased both as an ammeter and as a voltmeter.
(P.T.U.)

44. How is the current range of a permanent magnet moving coil instrument
extended with the help of a shunt? Illustrate with an example.
(B. Univ. June 1988) (U.P.T.U. Tut.)

45. Describe with neat sketch the principle, construction, and working of
dynamometer-type wattmeter.
(P.T.U.)

46. Name the two coils of a wattmeter. What is their function? How are they
connected? In a dynamometer wattmeter, which coil is excited by current and
which coil is excited by voltage? Why is it so?
(P.T.U.)

47. Explain why electrodynamometer-type instrument can be used both for AC and
DC measurements. Discuss the main sources of error in such instruments.
48. Explain the working of electrodynamometer type of instruments.
49. Explain the operating principle of an electrodynamic-type wattmeter.
50. Describe the construction and working principle of a dynamometer-type
wattmeter and show how its deflecting force is proportional to the average
value of power.
51. Mention advantages and disadvantages of dynamometer-type wattmeter.
(P.T.U.)

52. With appropriate mathematical derivations, explain the principle of

electrodynamic wattmeter.
53. Discuss the sources of errors in an electrodynamometer-type wattmeter.
(P.T.U.)

54. Explain the working principle of an induction-type wattmeter with the help of a
diagram.
55. Describe the working principle and construction of a single-phase induction-
type wattmeter. Show that deflecting torque is proportional to average power
of the circuit.
56. Describe the constructional details of a single-phase induction-type energy
meter, with the help of a circuit diagram.
(P.T.U.)

57. Describe the principle of induction-type energy meter.

(P.T.U.)

58. Describe with neat sketch the construction and working of single-phase energy
meter.
(P.T.U.)

59. Discuss the construction and working of a single-phase energy meter. What is
friction compensation? How is it provided?
(P.T.U.)

60. Describe the construction of a single-phase induction-type energy meter. Show

that the number of revolutions made by the disc is proportional to the energy
supplied.
61. What do you mean by creeping in an induction-type energy meter? How it can
be avoided?
62. What are the errors in induction-type energy meter?
(P.T.U.)

63. Explain different errors and their compensation in a single-phase energy

meter.
(P.T.U.)

64. Describe the functions of the following in a single-phase induction-type energy

meter.
(i) shunt and series magnets; (ii) moving disc; and (iii) permanent
brake magnet.
65. Explain the sources of errors in single-phase induction-type energy meters.
How are they eliminated?
66. Explain how the following adjustments are made in a single-phase induction-
type energy meter: (i) adjustment for friction compensation and (ii) overload.
 (P.T.U.)

67. Describe a two-element, three-phase energy meter.

(P.T.U.)

68. Describe with neat sketch the principle, construction, and working of a wright
maximum demand indicator and mention its uses.
(P.T.U.)

69. Why maximum demand indicators are used? Give its construction and working
principle.

(P.T.U.)

ANSWERS

Fill in the Blanks

1. random error
2. I2
3. having usually
4. deflecting
5. indicating
6. 1 kWh
7. indicating
8. indicating
9. energy meter
10. ammeter, energy meter
11. true
12. no controlling torque is provided
13. tangent galvanometer
14. absolute
15. does not affect
16. no damping torque is required in energy meter
17. operating mechanism
18. less
19. non-uniform
20. moving iron type
21. a shunt in parallel with operating coil
 22. DC
23. uniform
24. high
25. moving iron
26. non-uniform
27. high resistance
28. low
29. very small
30. uniform
31. DC measurements
32. square of the current passing through it
33. series
34. 25 to 200 μW
35. non-uniform
36. low
37. temperature
38. DC and AC
39. yes
40. I2
41. eddy current

42.
43. VI cos ɸ
44. VI cos θ
45. non-uniform
46. active
47. non-uniform
48. low
49. Induction-type energy meter
50. integrating
51. none
52. VI cos ɸ
53. time and power
54. voltage and current

Objective Type Questions

1. (b)
2. (c)
3. (c)
4. (b)
5. (d)
6. (d)
7. (b)
8. (d)
9. (b)
10. (a)
11. (b)
12. (c)
13. (d)
14. (a)
15. (b)
16. (c)
17. (c)
18. (b)
19. (d)
20. (c)
21. (a)
22. (c)
23. (a)
24. (c)
25. (b)
26. (d)
27. (c)
28. (b)
29. (d)
30. (c)
31. (b)
32. (a)
33. (d)