SAW Components

SAW IF filter
TD-SCDMA

Series/type: B5062
Ordering code: B39960B5062H310
Date: June 16, 2008
Version: 2.0

 EPCOS AG 2008. Reproduction, publication and dissemination of this data sheet, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
 SAW Components B5062
SAW IF filter 96.0 MHz
Data sheet
Application
■ Low-loss IF filter for TD-SCDMA base station
■ Unbalanced or balanced operation possible
■ High stopband suppression
■ Usable passband 20.0 MHz

Features
■ Package size 7.0 x 5.0 x 1.48 mm3
■ Package code QCC12C
■ RoHS compatible
■ Approximate weight 0.25 g
■ Package for Surface Mount Technology (SMT)
■ Ni, gold-plated terminals
■ Electrostatic Sensitive Device (ESD)
■ Filter surface passivated

Pin configuration
■ 10 Input
■ 12 Input ground
■ 4 Output
■ 6 Output ground
■ 1, 2, 7, 8 To be grounded
■ 3, 9 Case ground

Please read cautions and warnings and

important notes at the end of this document. 2 June 16, 2008
 SAW Components B5062
SAW IF filter 96.0 MHz
Data sheet
Characteristics
Temperature range for specification: T = –40 ˚C to +85 ˚C
Terminating source impedance: ZS = 50 Ω and matching network
Termnating load impedance: ZL = 50 Ω and matching network
Group delay aperture: 200 kHz

min. typ. max.

@ 25 ˚C
Nominal frequency fN — 96.0 — MHz

Minimum insertion attenuation αmin — 8.0 9.0 dB

(including matching network)

Passband width
αrel ≤ 1.4 dB B1.4dB 20 21.8 — MHz

Amplitude ripple (p-p) ∆α

fN ± 10.0 MHz — 1.0 1.4 dB

Group delay ripple (p-p) ∆τ

fN ± 10.0 MHz — 100 150 ns

Relative attenuation (relative to αmin) αrel

10.0 MHz ... 68.4 MHz 55 60 — dB
76.8 MHz 40 45 — dB
123.6 MHz ... 162.8 MHz 55 60 — dB
162.8 MHz ... 1.0 GHz 35 50 — dB

Return loss
Input fN ± 10.0 MHz — 7 — dB
Output fN ± 10.0 MHz — 8 — dB

1 dB compression point 12 — — dBm

Input IP3 35 — — dBm

Temperature coefficient of frequency TCf — –78 — ppm/K

Please read cautions and warnings and

important notes at the end of this document. 3 June 16, 2008
 SAW Components B5062
SAW IF filter 96.0 MHz
Data sheet

Matching network to 50 Ω

Ls2 Ls3
Cp1 = 33 pF
Ls2 = 180 nH
Cp1 Cp4
Ls3 = 270 nH
Cp4 = 22 pF

(Element values depend upon board layout and properties)

Maximum ratings
Operable temperature range T –40/+85 ˚C
Storage temperature range Tstg –40/+85 ˚C
DC voltage VDC 5 V
Input Power PIN 12 dBm

Please read cautions and warnings and

important notes at the end of this document. 4 June 16, 2008
 SAW Components B5062
SAW IF filter 96.0 MHz
Data sheet
Transfer function (S21, Narrowband)

Transfer function (S21, Wideband)

Please read cautions and warnings and

important notes at the end of this document. 5 June 16, 2008
 SAW Components B5062
SAW IF filter 96.0 MHz
Data sheet

References

Type B5062

Ordering code B39960B5062H310

Marking and package C61157-A7-A94

Packaging F61074-V8163-Z000

Date codes L_1126

S-parameters

Soldering profile S_6001

RoHS compatible defined as compatible with the following documents:

"DIRECTIVE 2002/95/EC OF THE EUROPEAN PARLIAMENT
AND OF THE COUNCIL of 27 January 2003 on the restriction
of the use of certain hazardous substances in electrical and
electronic equipment. 2005/618/EC from April 18th, 2005,
amending Directive 2002/95/EC of the European Parliament
and of the Council for the purposes of establishing the maxi-
mum concentration values for certain hazardous substances in
electrical and electronic equipment."

For further information please contact your local EPCOS sales office or visit our webpage at
www.epcos.com .

Published by EPCOS AG
Surface Acoustic Wave Components Division
P.O. Box 80 17 09, 81617 Munich, GERMANY
 EPCOS AG 2008. This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or
the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on
the type in question please also contact one of our Sales Offices.

Please read cautions and warnings and

important notes at the end of this document. 6 June 16, 2008
 Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties
described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained
by third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Conse-
quently, we cannot guarantee that all products named in this publication will always be avail-
able. The aforementioned does not apply in the case of individual agreements deviating from
the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the “General Terms of Delivery for Products and Services in the Electrical
Industry” published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIM-
DAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks reg-
istered or pending in Europe and in other countries. Further information will be found on the
Internet at www.epcos.com/trademarks.

7 June 16, 2008