Software Verification: Example Hong Kong Cp-04 Rc-Bm-001

Software Verification
PROGRAM NAME: SAFE

REVISION NO.: 4
EXAMPLE HONG KONG CP-04 RC-BM-001

Flexural and Shear Beam Design
PROBLEM DESCRIPTION
The purpose of this example is to verify slab flexural design in SAFE. The load
level is adjusted for the case corresponding to the following conditions:
 The stress-block extends below the flange but remains within the balanced
condition permitted by Hong Kong CP 2004.
 The average shear stress in the beam is below the maximum shear stress
allowed by Hong Kong CP 2004, requiring design shear reinforcement.
A simple-span, 6-m-long, 300-mm-wide, and 500-mm-deep T beam with a

flange 100 mm thick and 600 mm wide is modeled using SAFE. The beam is
shown in Figure 1. The computational model uses a finite element mesh of frame
elements, automatically generated by SAFE. The maximum element size has
been specified to be 200 mm. The beam is supported by columns without
rotational stiffnesses and with very large vertical stiffness (11020 kN/m).
The beam is loaded with symmetric third-point loading. One dead load case
(DL20) and one live load case (LL80) with only symmetric third-point loads of
magnitudes 20, and 80 kN, respectively, are defined in the model. One load
combinations (COMB80) is defined using the Hong Kong CP 2004 load
combination factors of 1.4 for dead loads and 1.6 for live loads. The model is
analyzed for both of these load cases and the load combinations.
The beam moment and shear force are computed analytically. The total factored
moment and shear force are compared with the SAFE results. These moment and
shear force are identical. After completing the analysis, design is performed
using the Hong Kong CP 2004 code in SAFE and also by hand computation. The
design longitudinal reinforcements are compared in Table 1. The design shear
reinforcements are compared in Table 2.
EXAMPLE HONG KONG CP-04 RC-BM-001 - 1

PROGRAM NAME: SAFE
REVISION NO.: 4
600 mm
75 mm 100 mm
500 mm
75 mm
300 mm
Beam Section
2000 mm 2000 mm 2000 mm
Shear Force
Bending Moment
Figure 1 The Model Beam for Flexural and Shear Design

PROGRAM NAME: SAFE
REVISION NO.: 4
GEOMETRY, PROPERTIES AND LOADING

Clear span, l = 6000 mm
Overall depth, h = 500 mm
Flange Thickness, ds = 100 mm
Width of web, bw = 300 mm
Width of flange, bf = 600 mm
Depth of tensile reinf., dc = 75 mm
Effective depth, d = 425 mm
Depth of comp. reinf., d' = 75 mm
Concrete strength, f' c = 30 MPa

Yield strength of steel, fy = 460 MPa
Concrete unit weight, wc = 0 kN/m3
Modulus of elasticity, Ec = 25105 MPa
Modulus of elasticity, Es = 2108 MPa
Poisson’s ratio, v = 0.2
Dead load, Pd = 20 kN
Live load, Pl = 80 kN
TECHNICAL FEATURES OF SAFE TESTED

 Calculation of flexural and shear reinforcement
 Application of minimum flexural and shear reinforcement
RESULTS COMPARISON
Table 1 shows the comparison of the SAFE total factored moments in the design
strip with the moments obtained by the analytical method. They match exactly
for this problem. Table 1 also shows the comparison of design reinforcements.
Table 1 Comparison of Moments and Flexural Reinforcements
Reinforcement Area (sq-cm)

Moment
Method (kN-m) As+
SAFE 312 20.904
Calculated 312 20.904
A s ,min = 195.00 sq-mm

PROGRAM NAME: SAFE
REVISION NO.: 4
Table 2 Comparison of Shear Reinforcements
Av
Reinforcement Area,
s
(sq-cm/m)
Shear Force (kN) SAFE Calculated
156 6.50 6.50
COMPUTER FILE: Hong Kong CP-04 RC-BM-001.FDB
CONCLUSION
The SAFE results show an approximate comparison with the independent results.

PROGRAM NAME: SAFE
REVISION NO.: 4
HAND CALCULATION
Flexural Design
The following quantities are computed for all the load combinations:
m, steel = 1.15
m, concrete = 1.50
As ,min  0.0013bw h
= 195.00 sq-mm
COMB80
P = (1.4Pd + 1.6Pt) =156 kN
N *l
M*  = 312 kN-m
3
The depth of the compression block is given by:
M
K= = 0.095963 < 0.156
f cu b f d 2
Then the moment arm is computed as:

 K 
z = d 0.5  0.25    0.95d = 373.4254 mm
 0.9 
The depth of the neutral axis is computed as:

1
x= (d − z) = 114.6102 mm
0.45
And the depth of the compression block is given by:
a = 0.9x = 103.1492 mm > hf
The ultimate resistance moment of the flange is given by:
fcu  b f  bw  h f  d  0.5h f  = 150.75 kN-m

0.67
Mf 
c

PROGRAM NAME: SAFE
REVISION NO.: 4
The moment taken by the web is computed as:

M w  M  M f = 161.25 kN-m
and the normalized moment resisted by the web is given by:

Mw
Kw = = 0.0991926 < 0.156
f cu bw d 2
If Kw  0.156 (BS 3.4.4.4), the beam is designed as a singly reinforced concrete
beam. The reinforcement is calculated as the sum of two parts: one to balance
compression in the flange and one to balance compression in the web.
 K 
z  d  0.5  0.25  w   0.95d = 371.3988 mm
 0.9 
Mf Mw
As   = 2090.4 sq-mm
 d  0.5h 
fy fy
z
s f
s
Shear Design
V
v  vmax = 1.2235 MPa
bw d
vmax = min(0.8 fcu , 5 MPa) = 4.38178 MPa
The shear stress carried by the concrete, vc, is calculated as:

1 1
0.79k1k 2  100 As  3  400  4
vc      = 0.3568 MPa
 m  bd   d 
k1 is the enhancement factor for support compression,
and is conservatively taken as 1 .
1 1
f  3  40  3
k2 =  cu  = 1.06266, 1  k2   
 25   25 
m = 1.25
100 As
= 0.15
bd

PROGRAM NAME: SAFE
REVISION NO.: 4
1
 400  4
  =1
 d 
However, the following limitations also apply:
100 As
0.15  3
bd
1
 400  4
  1
 d 
fcu  40 MPa (for calculation purposes only) and As is the area of tension
reinforcement.
Given v, vc, and vmax, the required shear reinforcement is calculated as follows:
If v  (vc + 0.4),
Asv 0.4bw

sv 0.87 f yv
If (vc + 0.4) < v  vmax,

Asv v  vc bw

sv 0.87 f yv
If v > vmax, a failure condition is declared.
(COMB80)
Pd = 20 kN
Pl = 80 kN
V = 156 kN
*
V
 =
*
= 2.0 MPa (sc < *  smax)
bw d
Asv v  vc bw
 = 0.64967sq-mm/mm = 6.50 sq-cm/m
sv 0.87 f yv

Software Verification: Example Hong Kong Cp-04 Rc-Bm-001

Uploaded by

Copyright:

Available Formats

Software Verification: Example Hong Kong Cp-04 Rc-Bm-001

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Software Verification: Example Hong Kong Cp-04 Rc-Bm-001

Uploaded by

Copyright:

Available Formats

Software Verification

PROGRAM NAME: SAFE

EXAMPLE HONG KONG CP-04 RC-BM-001

A simple-span, 6-m-long, 300-mm-wide, and 500-mm-deep T beam with a

EXAMPLE HONG KONG CP-04 RC-BM-001 - 1

2000 mm 2000 mm 2000 mm

Figure 1 The Model Beam for Flexural and Shear Design

EXAMPLE HONG KONG CP-04 RC-BM-001 - 2

GEOMETRY, PROPERTIES AND LOADING

Concrete strength, f' c = 30 MPa

TECHNICAL FEATURES OF SAFE TESTED

Table 1 Comparison of Moments and Flexural Reinforcements

Reinforcement Area (sq-cm)

SAFE 312 20.904

Calculated 312 20.904

A s ,min = 195.00 sq-mm

EXAMPLE HONG KONG CP-04 RC-BM-001 - 3

Table 2 Comparison of Shear Reinforcements

Shear Force (kN) SAFE Calculated

156 6.50 6.50

COMPUTER FILE: Hong Kong CP-04 RC-BM-001.FDB

EXAMPLE HONG KONG CP-04 RC-BM-001 - 4

Then the moment arm is computed as:

The depth of the neutral axis is computed as:

fcu  b f  bw  h f  d  0.5h f  = 150.75 kN-m

EXAMPLE HONG KONG CP-04 RC-BM-001 - 5

The moment taken by the web is computed as:

and the normalized moment resisted by the web is given by:

vmax = min(0.8 fcu , 5 MPa) = 4.38178 MPa

The shear stress carried by the concrete, vc, is calculated as:

EXAMPLE HONG KONG CP-04 RC-BM-001 - 6

If (vc + 0.4) < v  vmax,

EXAMPLE HONG KONG CP-04 RC-BM-001 - 7

You might also like