LC 5296 at
LC 5296 at
www.masibus.com sales@masibus.com
Technical Specifications:
Input Functional
Input Type Thermocouple (E, J, K, T, B, R, S), RTD (Pt100), Control Mode P, PI, PID, and ON/OFF control for Relay-1/SSR
Current, Voltage
Display Range Refer Table-1 Parameter Range
Accuracy ±0.25% of FS ±1 Count Proportional Band 0 to 9999
ADC Resolution 16 bits Integral Time 0 to 1000 seconds
Display Resolution 0.1 / 1.0 °C Derivative Time 0 to 180 seconds
Sampling Rate 4 Samples/Sec Cycle Time SSR: 1 to 60 sec
CJC Error ±2.0 °C Relay: 10 to 300 sec
Sensor open All inputs except 0-5V
Sensor Burnout current 0.25uA Power Supply
RTD excitation current 0.166mA (Approx) Standard 85-260VAC / 125-300VDC
NMRR > 40dB Optional 18-36VDC
CMRR > 120dB Power Consumption 10 VA Approx.
Temp-co < 150ppm/°C Isolation (Withstanding voltage)
Input Impedance > 1MΩ Between primary terminals* and secondary terminals**:
Max Voltage 20VDC At least 1500 V AC for 1 minute
Between primary terminals* and grounding terminal:
At least 1500 V AC for 1 minute
Display & Keys
Between grounding terminal and secondary terminals**:
Process Value 0.56", Red 4-digit At least 1500 V AC for 1 minute
Set Value 0.4", Green 4-digit Between secondary terminals**:
Relay & Communication Discrete LEDs At least 500 V AC for 1 minute
Keys SET1, SET2, Increase, Decrease * Primary terminals indicate power terminals and relay output terminals.
** Secondary terminals indicate analog I/O signal and Communication O/P.
Insulation resistance: 20MΩ or more at 500 V DC between power terminals and
Output grounding terminal
Control
Relay
2A @ 230VAC / 30VDC Physical
Single Change over (C, NO, NC) Dimensions:
Output
SSR 18VDC, 20mA Size 96(W) x 96(H) x 75(D) mm
Options
Voltage 0/1-5V, 0-10V @2KΩ Min. Front Bezel 96 x 96 mm
Current 0/4-20mA @500Ω Max. Panel Cutout 92.5 x 92.5 mm
Depth behind panel 65 mm
Alarm
2 Nos. (Max) Weight 300 gms approx.
Relays 2A @ 230VAC / 30VDC Enclosure Material Molded ABS
Single Change over (C, NO, NC) Enclosure Protection IP20
1 nos. Terminal Cable Size 2.5mm2
SSR
11VDC (10mA)
Retransmission Output
Current 0/4-20mA @500Ω Max. Table-1: Display Range
Voltage 0/1-5V, 0-10V @2KΩ Min. Input Type Range
Accuracy 0.25% of FS E -200 to 1000 ˚C
J -200 to 1200 ˚C
Transmitter Supply 24VDC (±10%) @30mA (Current limited) K -200 to 1372 ˚C
T -200 to 400 ˚C
Communication Output
B 450 to 1820 ˚C
Interface RS485
R 0 to 1768 ˚C
Protocol Modbus-RTU
S 0 to 1768 ˚C
Baud Rate 9600, 19200, 38400
Pt100 -200 to 850 ˚C, -199.0 to 850.0 ˚C
0/1-5V -1999 to 9999
Environmental
0/4-20mA (Ext.250Ω)
Operating temperature 0-55 °C
Storage temperature 0-80 °C
Humidity 20-95% RH non-condensing
Ordering Code
Options
Model Input Auxiliary Power Supply Output
Output-1 Output-2
LC5296-AT 1 E U1 80-265VAC / 125-300VDC 1 Relay-1 + Relay-2 N None N None
2 J U2 18-36VDC 2 SSR + Relay-2 1 4-20mA 1 4-20mA
3 K 2 0-20mA 2 0-20mA
4 T 3 1-5V 3 1-5V
5 B 4 0-5V 4 0-5V
6 R 5 0-10V 5 0-10V
7 S 6 RS485
9 Pt-100
C 1-5V
D 0-5V
E 4-20mA
F 0-20mA
Accessories: Two numbers mounting clamps